Skip to content

L
linux
Commit 8148c17b authored by Linus Torvalds's avatar Linus Torvalds
Browse files
Options

Merge tag 'gpio-v5.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio 

Pull gpio updates from Linus Walleij:
 "This is the bulk of the GPIO changes for the v5.2 kernel cycle. A bit
  later than usual because I was ironing out my own mistakes. I'm
  holding some stuff back for the next kernel as a result, and this
  should be a healthy and well tested batch.

  Core changes:

   - The gpiolib MMIO driver has been enhanced to handle two direction
     registers, i.e. one register to set lines as input and one register
     to set lines as output. It turns out some silicon engineer thinks
     the ability to configure a line as input and output at the same
     time makes sense, this can be debated but includes a lot of analog
     electronics reasoning, and the registers are there and need to be
     handled consistently. Unsurprisingly, we enforce the lines to be
     either inputs or outputs in such schemes.

   - Send in the proper argument value to .set_config() dispatched to
     the pin control subsystem. Nobody used it before, now someone does,
     so fix it to work as expected.

   - The ACPI gpiolib portions can now handle pin bias setting (pull up
     or pull down). This has been in the ACPI spec for years and we
     finally have it properly integrated with Linux GPIOs. It was based
     on an observation from Andy Schevchenko that Thomas Petazzoni's
     changes to the core for biasing the PCA950x GPIO expander actually
     happen to fit hand-in-glove with what the ACPI core needed. Such
     nice synergies happen sometimes.

  New drivers:

   - A new driver for the Mellanox BlueField GPIO controller. This is
     using 64bit MMIO registers and can configure lines as inputs and
     outputs at the same time and after improving the MMIO library we
     handle it just fine. Interesting.

   - A new IXP4xx proper gpiochip driver with hierarchical interrupts
     should be coming in from the ARM SoC tree as well.

  Driver enhancements:

   - The PCA053x driver handles the CAT9554 GPIO expander.

   - The PCA053x driver handles the NXP PCAL6416 GPIO expander.

   - Wake-up support on PCA053x GPIO lines.

   - OMAP now does a nice asynchronous IRQ handling on wake-ups by
     letting everything wake up on edges, and this makes runtime PM work
     as expected too.

  Misc:

   - Several cleanups such as devres fixes.

   - Get rid of some languager comstructs that cause problems when
     compiling with LLVMs clang.

   - Documentation review and update"

* tag 'gpio-v5.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (85 commits)
  gpio: Update documentation
  docs: gpio: convert docs to ReST and rename to *.rst
  gpio: sch: Remove write-only core_base
  gpio: pxa: Make two symbols static
  gpiolib: acpi: Respect pin bias setting
  gpiolib: acpi: Add acpi_gpio_update_gpiod_lookup_flags() helper
  gpiolib: acpi: Set pin value, based on bias, more accurately
  gpiolib: acpi: Change type of dflags
  gpiolib: Introduce GPIO_LOOKUP_FLAGS_DEFAULT
  gpiolib: Make use of enum gpio_lookup_flags consistent
  gpiolib: Indent entry values of enum gpio_lookup_flags
  gpio: pca953x: add support for pca6416
  dt-bindings: gpio: pca953x: document the nxp,pca6416
  gpio: pca953x: add pcal6416 to the of_device_id table
  gpio: gpio-omap: Remove conditional pm_runtime handling for GPIO interrupts
  gpio: gpio-omap: configure edge detection for level IRQs for idle wakeup
  tracing: stop making gpio tracing configurable
  gpio: pca953x: Configure wake-up path when wake-up is enabled
  gpio: of: Optimize quirk checks
  gpio: mmio: Drop bgpio_dir_inverted
  ...
parents 6fe567df 0fbee1df
Hide whitespace changes
Inline Side-by-side
Showing with 1052 additions and 1012 deletions
Documentation/devicetree/bindings/gpio/gpio-pca953x.txt
View file @ 8148c17b
......@@ -2,6 +2,7 @@
Required properties:
- compatible: Has to contain one of the following:
nxp,pca6416
nxp,pca9505
nxp,pca9534
nxp,pca9535
......@@ -30,6 +31,7 @@ Required properties:
ti,tca6424
ti,tca9539
ti,tca9554
onnn,cat9554
onnn,pca9654
exar,xra1202
- gpio-controller: if used as gpio expander.
......
Documentation/driver-api/gpio/driver.rst
View file @ 8148c17b
================================
GPIO Descriptor Driver Interface
================================
=====================
GPIO Driver Interface
=====================
This document serves as a guide for GPIO chip drivers writers. Note that it
describes the new descriptor-based interface. For a description of the
deprecated integer-based GPIO interface please refer to gpio-legacy.txt.
This document serves as a guide for writers of GPIO chip drivers.
Each GPIO controller driver needs to include the following header, which defines
the structures used to define a GPIO driver:
......@@ -15,32 +13,49 @@ the structures used to define a GPIO driver:
Internal Representation of GPIOs
================================
Inside a GPIO driver, individual GPIOs are identified by their hardware number,
which is a unique number between 0 and n, n being the number of GPIOs managed by
the chip. This number is purely internal: the hardware number of a particular
GPIO descriptor is never made visible outside of the driver.
On top of this internal number, each GPIO also need to have a global number in
the integer GPIO namespace so that it can be used with the legacy GPIO
A GPIO chip handles one or more GPIO lines. To be considered a GPIO chip, the
lines must conform to the definition: General Purpose Input/Output. If the
line is not general purpose, it is not GPIO and should not be handled by a
GPIO chip. The use case is the indicative: certain lines in a system may be
called GPIO but serve a very particular purpose thus not meeting the criteria
of a general purpose I/O. On the other hand a LED driver line may be used as a
GPIO and should therefore still be handled by a GPIO chip driver.
Inside a GPIO driver, individual GPIO lines are identified by their hardware
number, sometime also referred to as ``offset``, which is a unique number
between 0 and n-1, n being the number of GPIOs managed by the chip.
The hardware GPIO number should be something intuitive to the hardware, for
example if a system uses a memory-mapped set of I/O-registers where 32 GPIO
lines are handled by one bit per line in a 32-bit register, it makes sense to
use hardware offsets 0..31 for these, corresponding to bits 0..31 in the
register.
This number is purely internal: the hardware number of a particular GPIO
line is never made visible outside of the driver.
On top of this internal number, each GPIO line also needs to have a global
number in the integer GPIO namespace so that it can be used with the legacy GPIO
interface. Each chip must thus have a "base" number (which can be automatically
assigned), and for each GPIO the global number will be (base + hardware number).
Although the integer representation is considered deprecated, it still has many
users and thus needs to be maintained.
assigned), and for each GPIO line the global number will be (base + hardware
number). Although the integer representation is considered deprecated, it still
has many users and thus needs to be maintained.
So for example one platform could use numbers 32-159 for GPIOs, with a
So for example one platform could use global numbers 32-159 for GPIOs, with a
controller defining 128 GPIOs at a "base" of 32 ; while another platform uses
numbers 0..63 with one set of GPIO controllers, 64-79 with another type of GPIO
controller, and on one particular board 80-95 with an FPGA. The numbers need not
be contiguous; either of those platforms could also use numbers 2000-2063 to
identify GPIOs in a bank of I2C GPIO expanders.
global numbers 0..63 with one set of GPIO controllers, 64-79 with another type
of GPIO controller, and on one particular board 80-95 with an FPGA. The legacy
numbers need not be contiguous; either of those platforms could also use numbers
2000-2063 to identify GPIO lines in a bank of I2C GPIO expanders.
Controller Drivers: gpio_chip
=============================
In the gpiolib framework each GPIO controller is packaged as a "struct
gpio_chip" (see linux/gpio/driver.h for its complete definition) with members
common to each controller of that type:
gpio_chip" (see <linux/gpio/driver.h> for its complete definition) with members
common to each controller of that type, these should be assigned by the
driver code:
- methods to establish GPIO line direction
- methods used to access GPIO line values
......@@ -48,12 +63,12 @@ common to each controller of that type:
- method to return the IRQ number associated to a given GPIO line
- flag saying whether calls to its methods may sleep
- optional line names array to identify lines
- optional debugfs dump method (showing extra state like pullup config)
- optional debugfs dump method (showing extra state information)
- optional base number (will be automatically assigned if omitted)
- optional label for diagnostics and GPIO chip mapping using platform data
The code implementing a gpio_chip should support multiple instances of the
controller, possibly using the driver model. That code will configure each
controller, preferably using the driver model. That code will configure each
gpio_chip and issue ``gpiochip_add[_data]()`` or ``devm_gpiochip_add_data()``.
Removing a GPIO controller should be rare; use ``[devm_]gpiochip_remove()``
when it is unavoidable.
......@@ -62,24 +77,28 @@ Often a gpio_chip is part of an instance-specific structure with states not
exposed by the GPIO interfaces, such as addressing, power management, and more.
Chips such as audio codecs will have complex non-GPIO states.
Any debugfs dump method should normally ignore signals which haven't been
requested as GPIOs. They can use gpiochip_is_requested(), which returns either
NULL or the label associated with that GPIO when it was requested.
Any debugfs dump method should normally ignore lines which haven't been
requested. They can use gpiochip_is_requested(), which returns either
NULL or the label associated with that GPIO line when it was requested.
RT_FULL: the GPIO driver should not use spinlock_t or any sleepable APIs
(like PM runtime) in its gpio_chip implementation (.get/.set and direction
control callbacks) if it is expected to call GPIO APIs from atomic context
on -RT (inside hard IRQ handlers and similar contexts). Normally this should
not be required.
Realtime considerations: the GPIO driver should not use spinlock_t or any
sleepable APIs (like PM runtime) in its gpio_chip implementation (.get/.set
and direction control callbacks) if it is expected to call GPIO APIs from
atomic context on realtime kernels (inside hard IRQ handlers and similar
contexts). Normally this should not be required.
GPIO electrical configuration
-----------------------------
GPIOs can be configured for several electrical modes of operation by using the
.set_config() callback. Currently this API supports setting debouncing and
single-ended modes (open drain/open source). These settings are described
below.
GPIO lines can be configured for several electrical modes of operation by using
the .set_config() callback. Currently this API supports setting:
- Debouncing
- Single-ended modes (open drain/open source)
- Pull up and pull down resistor enablement
These settings are described below.
The .set_config() callback uses the same enumerators and configuration
semantics as the generic pin control drivers. This is not a coincidence: it is
......@@ -94,8 +113,8 @@ description needs to provide "GPIO ranges" mapping the GPIO line offsets to pin
numbers on the pin controller so they can properly cross-reference each other.
GPIOs with debounce support
---------------------------
GPIO lines with debounce support
--------------------------------
Debouncing is a configuration set to a pin indicating that it is connected to
a mechanical switch or button, or similar that may bounce. Bouncing means the
......@@ -111,8 +130,8 @@ a certain number of milliseconds for debouncing, or just "on/off" if that time
is not configurable.
GPIOs with open drain/source support
------------------------------------
GPIO lines with open drain/source support
-----------------------------------------
Open drain (CMOS) or open collector (TTL) means the line is not actively driven
high: instead you provide the drain/collector as output, so when the transistor
......@@ -132,13 +151,13 @@ This configuration is normally used as a way to achieve one of two things:
- Level-shifting: to reach a logical level higher than that of the silicon
where the output resides.
- inverse wire-OR on an I/O line, for example a GPIO line, making it possible
- Inverse wire-OR on an I/O line, for example a GPIO line, making it possible
for any driving stage on the line to drive it low even if any other output
to the same line is simultaneously driving it high. A special case of this
is driving the SCL and SDA lines of an I2C bus, which is by definition a
wire-OR bus.
Both usecases require that the line be equipped with a pull-up resistor. This
Both use cases require that the line be equipped with a pull-up resistor. This
resistor will make the line tend to high level unless one of the transistors on
the rail actively pulls it down.
......@@ -208,27 +227,91 @@ For open source configuration the same principle is used, just that instead
of actively driving the line low, it is set to input.
GPIO lines with pull up/down resistor support
---------------------------------------------
A GPIO line can support pull-up/down using the .set_config() callback. This
means that a pull up or pull-down resistor is available on the output of the
GPIO line, and this resistor is software controlled.
In discrete designs, a pull-up or pull-down resistor is simply soldered on
the circuit board. This is not something we deal or model in software. The
most you will think about these lines is that they will very likely be
configured as open drain or open source (see the section above).
The .set_config() callback can only turn pull up or down on and off, and will
no have any semantic knowledge about the resistance used. It will only say
switch a bit in a register enabling or disabling pull-up or pull-down.
If the GPIO line supports shunting in different resistance values for the
pull-up or pull-down resistor, the GPIO chip callback .set_config() will not
suffice. For these complex use cases, a combined GPIO chip and pin controller
need to be implemented, as the pin config interface of a pin controller
supports more versatile control over electrical properties and can handle
different pull-up or pull-down resistance values.
GPIO drivers providing IRQs
---------------------------
===========================
It is custom that GPIO drivers (GPIO chips) are also providing interrupts,
most often cascaded off a parent interrupt controller, and in some special
cases the GPIO logic is melded with a SoC's primary interrupt controller.
The IRQ portions of the GPIO block are implemented using an irqchip, using
The IRQ portions of the GPIO block are implemented using an irq_chip, using
the header <linux/irq.h>. So basically such a driver is utilizing two sub-
systems simultaneously: gpio and irq.
RT_FULL: a realtime compliant GPIO driver should not use spinlock_t or any
sleepable APIs (like PM runtime) as part of its irq_chip implementation.
It is legal for any IRQ consumer to request an IRQ from any irqchip even if it
is a combined GPIO+IRQ driver. The basic premise is that gpio_chip and
irq_chip are orthogonal, and offering their services independent of each
other.
* spinlock_t should be replaced with raw_spinlock_t [1].
* If sleepable APIs have to be used, these can be done from the .irq_bus_lock()
gpiod_to_irq() is just a convenience function to figure out the IRQ for a
certain GPIO line and should not be relied upon to have been called before
the IRQ is used.
Always prepare the hardware and make it ready for action in respective
callbacks from the GPIO and irq_chip APIs. Do not rely on gpiod_to_irq() having
been called first.
We can divide GPIO irqchips in two broad categories:
- CASCADED INTERRUPT CHIPS: this means that the GPIO chip has one common
interrupt output line, which is triggered by any enabled GPIO line on that
chip. The interrupt output line will then be routed to an parent interrupt
controller one level up, in the most simple case the systems primary
interrupt controller. This is modeled by an irqchip that will inspect bits
inside the GPIO controller to figure out which line fired it. The irqchip
part of the driver needs to inspect registers to figure this out and it
will likely also need to acknowledge that it is handling the interrupt
by clearing some bit (sometime implicitly, by just reading a status
register) and it will often need to set up the configuration such as
edge sensitivity (rising or falling edge, or high/low level interrupt for
example).
- HIERARCHICAL INTERRUPT CHIPS: this means that each GPIO line has a dedicated
irq line to a parent interrupt controller one level up. There is no need
to inquire the GPIO hardware to figure out which line has figured, but it
may still be necessary to acknowledge the interrupt and set up the
configuration such as edge sensitivity.
Realtime considerations: a realtime compliant GPIO driver should not use
spinlock_t or any sleepable APIs (like PM runtime) as part of its irqchip
implementation.
- spinlock_t should be replaced with raw_spinlock_t [1].
- If sleepable APIs have to be used, these can be done from the .irq_bus_lock()
and .irq_bus_unlock() callbacks, as these are the only slowpath callbacks
on an irqchip. Create the callbacks if needed [2].
GPIO irqchips usually fall in one of two categories:
* CHAINED GPIO irqchips: these are usually the type that is embedded on
Cascaded GPIO irqchips
----------------------
Cascaded GPIO irqchips usually fall in one of three categories:
- CHAINED CASCADED GPIO IRQCHIPS: these are usually the type that is embedded on
an SoC. This means that there is a fast IRQ flow handler for the GPIOs that
gets called in a chain from the parent IRQ handler, most typically the
system interrupt controller. This means that the GPIO irqchip handler will
......@@ -245,16 +328,19 @@ GPIO irqchips usually fall in one of two categories:
struct gpio_chip, as everything happens directly in the callbacks: no
slow bus traffic like I2C can be used.
RT_FULL: Note, chained IRQ handlers will not be forced threaded on -RT.
As result, spinlock_t or any sleepable APIs (like PM runtime) can't be used
in chained IRQ handler.
If required (and if it can't be converted to the nested threaded GPIO irqchip)
a chained IRQ handler can be converted to generic irq handler and this way
it will be a threaded IRQ handler on -RT and a hard IRQ handler on non-RT
(for example, see [3]).
Know W/A: The generic_handle_irq() is expected to be called with IRQ disabled,
Realtime considerations: Note that chained IRQ handlers will not be forced
threaded on -RT. As a result, spinlock_t or any sleepable APIs (like PM
runtime) can't be used in a chained IRQ handler.
If required (and if it can't be converted to the nested threaded GPIO irqchip,
see below) a chained IRQ handler can be converted to generic irq handler and
this way it will become a threaded IRQ handler on -RT and a hard IRQ handler
on non-RT (for example, see [3]).
The generic_handle_irq() is expected to be called with IRQ disabled,
so the IRQ core will complain if it is called from an IRQ handler which is
forced to a thread. The "fake?" raw lock can be used to W/A this problem::
forced to a thread. The "fake?" raw lock can be used to work around this
problem::
raw_spinlock_t wa_lock;
static irqreturn_t omap_gpio_irq_handler(int irq, void *gpiobank)
......@@ -263,7 +349,7 @@ GPIO irqchips usually fall in one of two categories:
generic_handle_irq(irq_find_mapping(bank->chip.irq.domain, bit));
raw_spin_unlock_irqrestore(&bank->wa_lock, wa_lock_flags);
* GENERIC CHAINED GPIO irqchips: these are the same as "CHAINED GPIO irqchips",
- GENERIC CHAINED GPIO IRQCHIPS: these are the same as "CHAINED GPIO irqchips",
but chained IRQ handlers are not used. Instead GPIO IRQs dispatching is
performed by generic IRQ handler which is configured using request_irq().
The GPIO irqchip will then end up calling something like this sequence in
......@@ -273,16 +359,19 @@ GPIO irqchips usually fall in one of two categories:
for each detected GPIO IRQ
generic_handle_irq(...);
RT_FULL: Such kind of handlers will be forced threaded on -RT, as result IRQ
core will complain that generic_handle_irq() is called with IRQ enabled and
the same W/A as for "CHAINED GPIO irqchips" can be applied.
Realtime considerations: this kind of handlers will be forced threaded on -RT,
and as result the IRQ core will complain that generic_handle_irq() is called
with IRQ enabled and the same work around as for "CHAINED GPIO irqchips" can
be applied.
- NESTED THREADED GPIO IRQCHIPS: these are off-chip GPIO expanders and any
other GPIO irqchip residing on the other side of a sleeping bus such as I2C
or SPI.
* NESTED THREADED GPIO irqchips: these are off-chip GPIO expanders and any
other GPIO irqchip residing on the other side of a sleeping bus. Of course
such drivers that need slow bus traffic to read out IRQ status and similar,
traffic which may in turn incur other IRQs to happen, cannot be handled
in a quick IRQ handler with IRQs disabled. Instead they need to spawn a
thread and then mask the parent IRQ line until the interrupt is handled
Of course such drivers that need slow bus traffic to read out IRQ status and
similar, traffic which may in turn incur other IRQs to happen, cannot be
handled in a quick IRQ handler with IRQs disabled. Instead they need to spawn
a thread and then mask the parent IRQ line until the interrupt is handled
by the driver. The hallmark of this driver is to call something like
this in its interrupt handler::
......@@ -294,36 +383,46 @@ GPIO irqchips usually fall in one of two categories:
flag on struct gpio_chip to true, indicating that this chip may sleep
when accessing the GPIOs.
These kinds of irqchips are inherently realtime tolerant as they are
already set up to handle sleeping contexts.
Infrastructure helpers for GPIO irqchips
----------------------------------------
To help out in handling the set-up and management of GPIO irqchips and the
associated irqdomain and resource allocation callbacks, the gpiolib has
some helpers that can be enabled by selecting the GPIOLIB_IRQCHIP Kconfig
symbol:
* gpiochip_irqchip_add(): adds a chained irqchip to a gpiochip. It will pass
the struct gpio_chip* for the chip to all IRQ callbacks, so the callbacks
need to embed the gpio_chip in its state container and obtain a pointer
to the container using container_of().
- gpiochip_irqchip_add(): adds a chained cascaded irqchip to a gpiochip. It
will pass the struct gpio_chip* for the chip to all IRQ callbacks, so the
callbacks need to embed the gpio_chip in its state container and obtain a
pointer to the container using container_of().
(See Documentation/driver-model/design-patterns.txt)
* gpiochip_irqchip_add_nested(): adds a nested irqchip to a gpiochip.
- gpiochip_irqchip_add_nested(): adds a nested cascaded irqchip to a gpiochip,
as discussed above regarding different types of cascaded irqchips. The
cascaded irq has to be handled by a threaded interrupt handler.
Apart from that it works exactly like the chained irqchip.
* gpiochip_set_chained_irqchip(): sets up a chained irq handler for a
- gpiochip_set_chained_irqchip(): sets up a chained cascaded irq handler for a
gpio_chip from a parent IRQ and passes the struct gpio_chip* as handler
data. (Notice handler data, since the irqchip data is likely used by the
parent irqchip!).
data. Notice that we pass is as the handler data, since the irqchip data is
likely used by the parent irqchip.
* gpiochip_set_nested_irqchip(): sets up a nested irq handler for a
- gpiochip_set_nested_irqchip(): sets up a nested cascaded irq handler for a
gpio_chip from a parent IRQ. As the parent IRQ has usually been
explicitly requested by the driver, this does very little more than
mark all the child IRQs as having the other IRQ as parent.
If there is a need to exclude certain GPIOs from the IRQ domain, you can
set .irq.need_valid_mask of the gpiochip before gpiochip_add_data() is
called. This allocates an .irq.valid_mask with as many bits set as there
are GPIOs in the chip. Drivers can exclude GPIOs by clearing bits from this
mask. The mask must be filled in before gpiochip_irqchip_add() or
gpiochip_irqchip_add_nested() is called.
If there is a need to exclude certain GPIO lines from the IRQ domain handled by
these helpers, we can set .irq.need_valid_mask of the gpiochip before
[devm_]gpiochip_add_data() is called. This allocates an .irq.valid_mask with as
many bits set as there are GPIO lines in the chip, each bit representing line
0..n-1. Drivers can exclude GPIO lines by clearing bits from this mask. The mask
must be filled in before gpiochip_irqchip_add() or gpiochip_irqchip_add_nested()
is called.
To use the helpers please keep the following in mind:
......@@ -333,33 +432,24 @@ To use the helpers please keep the following in mind:
- Nominally set all handlers to handle_bad_irq() in the setup call and pass
handle_bad_irq() as flow handler parameter in gpiochip_irqchip_add() if it is
expected for GPIO driver that irqchip .set_type() callback have to be called
before using/enabling GPIO IRQ. Then set the handler to handle_level_irq()
and/or handle_edge_irq() in the irqchip .set_type() callback depending on
what your controller supports.
expected for GPIO driver that irqchip .set_type() callback will be called
before using/enabling each GPIO IRQ. Then set the handler to
handle_level_irq() and/or handle_edge_irq() in the irqchip .set_type()
callback depending on what your controller supports and what is requested
by the consumer.
It is legal for any IRQ consumer to request an IRQ from any irqchip no matter
if that is a combined GPIO+IRQ driver. The basic premise is that gpio_chip and
irq_chip are orthogonal, and offering their services independent of each
other.
gpiod_to_irq() is just a convenience function to figure out the IRQ for a
certain GPIO line and should not be relied upon to have been called before
the IRQ is used.
So always prepare the hardware and make it ready for action in respective
callbacks from the GPIO and irqchip APIs. Do not rely on gpiod_to_irq() having
been called first.
Locking IRQ usage
-----------------
This orthogonality leads to ambiguities that we need to solve: if there is
competition inside the subsystem which side is using the resource (a certain
GPIO line and register for example) it needs to deny certain operations and
keep track of usage inside of the gpiolib subsystem. This is why the API
below exists.
Since GPIO and irq_chip are orthogonal, we can get conflicts between different
use cases. For example a GPIO line used for IRQs should be an input line,
it does not make sense to fire interrupts on an output GPIO.
If there is competition inside the subsystem which side is using the
resource (a certain GPIO line and register for example) it needs to deny
certain operations and keep track of usage inside of the gpiolib subsystem.
Locking IRQ usage
-----------------
Input GPIOs can be used as IRQ signals. When this happens, a driver is requested
to mark the GPIO as being used as an IRQ::
......@@ -380,9 +470,15 @@ assigned.
Disabling and enabling IRQs
---------------------------
In some (fringe) use cases, a driver may be using a GPIO line as input for IRQs,
but occasionally switch that line over to drive output and then back to being
an input with interrupts again. This happens on things like CEC (Consumer
Electronics Control).
When a GPIO is used as an IRQ signal, then gpiolib also needs to know if
the IRQ is enabled or disabled. In order to inform gpiolib about this,
a driver should call::
the irqchip driver should call::
void gpiochip_disable_irq(struct gpio_chip *chip, unsigned int offset)
......@@ -398,40 +494,45 @@ irqchip.
When using the gpiolib irqchip helpers, these callbacks are automatically
assigned.
Real-Time compliance for GPIO IRQ chips
---------------------------------------
Any provider of irqchips needs to be carefully tailored to support Real Time
Any provider of irqchips needs to be carefully tailored to support Real-Time
preemption. It is desirable that all irqchips in the GPIO subsystem keep this
in mind and do the proper testing to assure they are real time-enabled.
So, pay attention on above " RT_FULL:" notes, please.
The following is a checklist to follow when preparing a driver for real
time-compliance:
- ensure spinlock_t is not used as part irq_chip implementation;
- ensure that sleepable APIs are not used as part irq_chip implementation.
So, pay attention on above realtime considerations in the documentation.
The following is a checklist to follow when preparing a driver for real-time
compliance:
- ensure spinlock_t is not used as part irq_chip implementation
- ensure that sleepable APIs are not used as part irq_chip implementation
If sleepable APIs have to be used, these can be done from the .irq_bus_lock()
and .irq_bus_unlock() callbacks;
and .irq_bus_unlock() callbacks
- Chained GPIO irqchips: ensure spinlock_t or any sleepable APIs are not used
from chained IRQ handler;
from the chained IRQ handler
- Generic chained GPIO irqchips: take care about generic_handle_irq() calls and
apply corresponding W/A;
- Chained GPIO irqchips: get rid of chained IRQ handler and use generic irq
handler if possible :)
- regmap_mmio: Sry, but you are in trouble :( if MMIO regmap is used as for
GPIO IRQ chip implementation;
- Test your driver with the appropriate in-kernel real time test cases for both
level and edge IRQs.
apply corresponding work-around
- Chained GPIO irqchips: get rid of the chained IRQ handler and use generic irq
handler if possible
- regmap_mmio: it is possible to disable internal locking in regmap by setting
.disable_locking and handling the locking in the GPIO driver
- Test your driver with the appropriate in-kernel real-time test cases for both
level and edge IRQs
* [1] http://www.spinics.net/lists/linux-omap/msg120425.html
* [2] https://lkml.org/lkml/2015/9/25/494
* [3] https://lkml.org/lkml/2015/9/25/495
Requesting self-owned GPIO pins
-------------------------------
===============================
Sometimes it is useful to allow a GPIO chip driver to request its own GPIO
descriptors through the gpiolib API. Using gpio_request() for this purpose
does not help since it pins the module to the kernel forever (it calls
try_module_get()). A GPIO driver can use the following functions instead
to request and free descriptors without being pinned to the kernel forever::
descriptors through the gpiolib API. A GPIO driver can use the following
functions to request and free descriptors::
struct gpio_desc *gpiochip_request_own_desc(struct gpio_desc *desc,
u16 hwnum,
......@@ -446,7 +547,3 @@ gpiochip_free_own_desc().
These functions must be used with care since they do not affect module use
count. Do not use the functions to request gpio descriptors not owned by the
calling driver.
* [1] http://www.spinics.net/lists/linux-omap/msg120425.html
* [2] https://lkml.org/lkml/2015/9/25/494
* [3] https://lkml.org/lkml/2015/9/25/495
Documentation/gpio/index.rst 0 → 100644
View file @ 8148c17b
:orphan:
====
gpio
====
.. toctree::
:maxdepth: 1
sysfs
.. only:: subproject and html
Indices
=======
* :ref:`genindex`
Documentation/gpio/sysfs.txt → Documentation/gpio/sysfs.rst
View file @ 8148c17b
GPIO Sysfs Interface for Userspace
==================================
THIS ABI IS DEPRECATED, THE ABI DOCUMENTATION HAS BEEN MOVED TO
Documentation/ABI/obsolete/sysfs-gpio AND NEW USERSPACE CONSUMERS
ARE SUPPOSED TO USE THE CHARACTER DEVICE ABI. THIS OLD SYSFS ABI WILL
NOT BE DEVELOPED (NO NEW FEATURES), IT WILL JUST BE MAINTAINED.
.. warning::
THIS ABI IS DEPRECATED, THE ABI DOCUMENTATION HAS BEEN MOVED TO
Documentation/ABI/obsolete/sysfs-gpio AND NEW USERSPACE CONSUMERS
ARE SUPPOSED TO USE THE CHARACTER DEVICE ABI. THIS OLD SYSFS ABI WILL
NOT BE DEVELOPED (NO NEW FEATURES), IT WILL JUST BE MAINTAINED.
Refer to the examples in tools/gpio/* for an introduction to the new
character device ABI. Also see the userspace header in
......@@ -51,13 +53,15 @@ The control interfaces are write-only:
/sys/class/gpio/
"export" ... Userspace may ask the kernel to export control of
"export" ...
Userspace may ask the kernel to export control of
a GPIO to userspace by writing its number to this file.
Example: "echo 19 > export" will create a "gpio19" node
for GPIO #19, if that's not requested by kernel code.
"unexport" ... Reverses the effect of exporting to userspace.
"unexport" ...
Reverses the effect of exporting to userspace.
Example: "echo 19 > unexport" will remove a "gpio19"
node exported using the "export" file.
......@@ -67,7 +71,8 @@ and have the following read/write attributes:
/sys/class/gpio/gpioN/
"direction" ... reads as either "in" or "out". This value may
"direction" ...
reads as either "in" or "out". This value may
normally be written. Writing as "out" defaults to
initializing the value as low. To ensure glitch free
operation, values "low" and "high" may be written to
......@@ -78,7 +83,8 @@ and have the following read/write attributes:
it was exported by kernel code that didn't explicitly
allow userspace to reconfigure this GPIO's direction.
"value" ... reads as either 0 (low) or 1 (high). If the GPIO
"value" ...
reads as either 0 (low) or 1 (high). If the GPIO
is configured as an output, this value may be written;
any nonzero value is treated as high.
......@@ -92,14 +98,16 @@ and have the following read/write attributes:
file and read the new value or close the file and re-open it
to read the value.
"edge" ... reads as either "none", "rising", "falling", or
"edge" ...
reads as either "none", "rising", "falling", or
"both". Write these strings to select the signal edge(s)
that will make poll(2) on the "value" file return.
This file exists only if the pin can be configured as an
interrupt generating input pin.
"active_low" ... reads as either 0 (false) or 1 (true). Write
"active_low" ...
reads as either 0 (false) or 1 (true). Write
any nonzero value to invert the value attribute both
for reading and writing. Existing and subsequent
poll(2) support configuration via the edge attribute
......@@ -112,11 +120,14 @@ read-only attributes:
/sys/class/gpio/gpiochipN/
"base" ... same as N, the first GPIO managed by this chip
"base" ...
same as N, the first GPIO managed by this chip
"label" ... provided for diagnostics (not always unique)
"label" ...
provided for diagnostics (not always unique)
"ngpio" ... how many GPIOs this manages (N to N + ngpio - 1)
"ngpio" ...
how many GPIOs this manages (N to N + ngpio - 1)
Board documentation should in most cases cover what GPIOs are used for
what purposes. However, those numbers are not always stable; GPIOs on
......@@ -129,7 +140,7 @@ the correct GPIO number to use for a given signal.
Exporting from Kernel code
--------------------------
Kernel code can explicitly manage exports of GPIOs which have already been
requested using gpio_request():
requested using gpio_request()::
/* export the GPIO to userspace */
int gpiod_export(struct gpio_desc *desc, bool direction_may_change);
......
arch/arm/configs/aspeed_g4_defconfig
View file @ 8148c17b
......@@ -247,7 +247,6 @@ CONFIG_PANIC_TIMEOUT=-1
# CONFIG_SCHED_DEBUG is not set
CONFIG_SCHED_STACK_END_CHECK=y
CONFIG_FUNCTION_TRACER=y
# CONFIG_TRACING_EVENTS_GPIO is not set
# CONFIG_RUNTIME_TESTING_MENU is not set
CONFIG_DEBUG_WX=y
CONFIG_DEBUG_USER=y
......
arch/arm/configs/aspeed_g5_defconfig
View file @ 8148c17b
......@@ -247,7 +247,6 @@ CONFIG_PANIC_TIMEOUT=-1
# CONFIG_SCHED_DEBUG is not set
CONFIG_SCHED_STACK_END_CHECK=y
CONFIG_FUNCTION_TRACER=y
# CONFIG_TRACING_EVENTS_GPIO is not set
# CONFIG_RUNTIME_TESTING_MENU is not set
CONFIG_DEBUG_WX=y
CONFIG_DEBUG_USER=y
......
drivers/gpio/Kconfig
View file @ 8148c17b
......@@ -26,12 +26,12 @@ config GPIOLIB_FASTPATH_LIMIT
range 32 512
default 512
help
This adjusts the point at which certain APIs will switch from
using a stack allocated buffer to a dynamically allocated buffer.
This adjusts the point at which certain APIs will switch from
using a stack allocated buffer to a dynamically allocated buffer.
You shouldn't need to change this unless you really need to
optimize either stack space or performance. Change this carefully
since setting an incorrect value could cause stack corruption.
You shouldn't need to change this unless you really need to
optimize either stack space or performance. Change this carefully
since setting an incorrect value could cause stack corruption.
config OF_GPIO
def_bool y
......@@ -319,7 +319,7 @@ config GPIO_MENZ127
depends on MCB
select GPIO_GENERIC
help
Say yes here to support the MEN 16Z127 GPIO Controller
Say yes here to support the MEN 16Z127 GPIO Controller
config GPIO_MM_LANTIQ
bool "Lantiq Memory mapped GPIOs"
......@@ -329,20 +329,6 @@ config GPIO_MM_LANTIQ
(EBU) found on Lantiq SoCs. The gpios are output only as they are
created by attaching a 16bit latch to the bus.
config GPIO_MOCKUP
tristate "GPIO Testing Driver"
depends on GPIOLIB && SYSFS
select GPIO_SYSFS
select GPIOLIB_IRQCHIP
select IRQ_SIM
help
This enables GPIO Testing driver, which provides a way to test GPIO
subsystem through sysfs(or char device) and debugfs. GPIO_SYSFS
must be selected for this test.
User could use it through the script in
tools/testing/selftests/gpio/gpio-mockup.sh. Reference the usage in
it.
config GPIO_MPC5200
def_bool y
depends on PPC_MPC52xx
......@@ -861,11 +847,11 @@ config GPIO_MAX732X
Input and Output (designed by 'P'). The combinations are listed
below:
8 bits: max7319 (8I), max7320 (8O), max7321 (8P),
max7322 (4I4O), max7323 (4P4O)
8 bits: max7319 (8I), max7320 (8O), max7321 (8P),
max7322 (4I4O), max7323 (4P4O)
16 bits: max7324 (8I8O), max7325 (8P8O),
max7326 (4I12O), max7327 (4P12O)
16 bits: max7324 (8I8O), max7325 (8P8O),
max7326 (4I12O), max7327 (4P12O)
Board setup code must specify the model to use, and the start
number for these GPIOs.
......@@ -892,17 +878,17 @@ config GPIO_PCA953X
SMBus I/O expanders, made mostly by NXP or TI. Compatible
models include:
4 bits: pca9536, pca9537
4 bits: pca9536, pca9537
8 bits: max7310, max7315, pca6107, pca9534, pca9538, pca9554,
pca9556, pca9557, pca9574, tca6408, tca9554, xra1202
8 bits: max7310, max7315, pca6107, pca9534, pca9538, pca9554,
pca9556, pca9557, pca9574, tca6408, tca9554, xra1202
16 bits: max7312, max7313, pca9535, pca9539, pca9555, pca9575,
tca6416
16 bits: max7312, max7313, pca9535, pca9539, pca9555, pca9575,
tca6416
24 bits: tca6424
24 bits: tca6424
40 bits: pca9505, pca9698
40 bits: pca9505, pca9698
config GPIO_PCA953X_IRQ
bool "Interrupt controller support for PCA953x"
......@@ -924,7 +910,7 @@ config GPIO_PCF857X
8 bits: pcf8574, pcf8574a, pca8574, pca8574a,
pca9670, pca9672, pca9674, pca9674a,
max7328, max7329
max7328, max7329
16 bits: pcf8575, pcf8575c, pca8575,
pca9671, pca9673, pca9675
......@@ -1046,9 +1032,9 @@ config HTC_EGPIO
bool "HTC EGPIO support"
depends on GPIOLIB && ARM
help
This driver supports the CPLD egpio chip present on
several HTC phones. It provides basic support for input
pins, output pins, and irqs.
This driver supports the CPLD egpio chip present on
several HTC phones. It provides basic support for input
pins, output pins, and irqs.
config GPIO_JANZ_TTL
tristate "Janz VMOD-TTL Digital IO Module"
......@@ -1084,7 +1070,7 @@ config GPIO_LP873X
on LP873X PMICs.
This driver can also be built as a module. If so, the module will be
called gpio-lp873x.
called gpio-lp873x.
config GPIO_LP87565
tristate "TI LP87565 GPIO"
......@@ -1315,6 +1301,13 @@ config GPIO_MERRIFIELD
help
Say Y here to support Intel Merrifield GPIO.
config GPIO_MLXBF
tristate "Mellanox BlueField SoC GPIO"
depends on (MELLANOX_PLATFORM && ARM64 && ACPI) || (64BIT && COMPILE_TEST)
select GPIO_GENERIC
help
Say Y here if you want GPIO support on Mellanox BlueField SoC.
config GPIO_ML_IOH
tristate "OKI SEMICONDUCTOR ML7213 IOH GPIO support"
depends on X86 || COMPILE_TEST
......@@ -1435,10 +1428,22 @@ config GPIO_VIPERBOARD
Say yes here to access the GPIO signals of Nano River
Technologies Viperboard. There are two GPIO chips on the
board: gpioa and gpiob.
See viperboard API specification and Nano
River Tech's viperboard.h for detailed meaning
of the module parameters.
See viperboard API specification and Nano
River Tech's viperboard.h for detailed meaning
of the module parameters.
endmenu
config GPIO_MOCKUP
tristate "GPIO Testing Driver"
depends on GPIOLIB
select IRQ_SIM
help
This enables GPIO Testing driver, which provides a way to test GPIO
subsystem through sysfs(or char device) and debugfs. GPIO_SYSFS
must be selected for this test.
User could use it through the script in
tools/testing/selftests/gpio/gpio-mockup.sh. Reference the usage in
it.
endif
drivers/gpio/Makefile
View file @ 8148c17b
......@@ -85,6 +85,7 @@ obj-$(CONFIG_GPIO_MENZ127) += gpio-menz127.o
obj-$(CONFIG_GPIO_MERRIFIELD) += gpio-merrifield.o
obj-$(CONFIG_GPIO_MC33880) += gpio-mc33880.o
obj-$(CONFIG_GPIO_MC9S08DZ60) += gpio-mc9s08dz60.o
obj-$(CONFIG_GPIO_MLXBF) += gpio-mlxbf.o
obj-$(CONFIG_GPIO_ML_IOH) += gpio-ml-ioh.o
obj-$(CONFIG_GPIO_MM_LANTIQ) += gpio-mm-lantiq.o
obj-$(CONFIG_GPIO_MOCKUP) += gpio-mockup.o
......
drivers/gpio/gpio-74x164.c
View file @ 8148c17b
// SPDX-License-Identifier: GPL-2.0-only
/*
* 74Hx164 - Generic serial-in/parallel-out 8-bits shift register GPIO driver
*
* Copyright (C) 2010 Gabor Juhos <juhosg@openwrt.org>
* Copyright (C) 2010 Miguel Gaio <miguel.gaio@efixo.com>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
#include <linux/init.h>
#include <linux/mutex.h>
#include <linux/spi/spi.h>
#include <linux/gpio/driver.h>
#include <linux/gpio/consumer.h>
#include <linux/slab.h>
#include <linux/gpio/driver.h>
#include <linux/module.h>
#include <linux/mutex.h>
#include <linux/property.h>
#include <linux/slab.h>
#include <linux/spi/spi.h>
#define GEN_74X164_NUMBER_GPIOS 8
......@@ -116,10 +113,9 @@ static int gen_74x164_probe(struct spi_device *spi)
if (ret < 0)
return ret;
if (of_property_read_u32(spi->dev.of_node, "registers-number",
&nregs)) {
dev_err(&spi->dev,
"Missing registers-number property in the DT.\n");
ret = device_property_read_u32(&spi->dev, "registers-number", &nregs);
if (ret) {
dev_err(&spi->dev, "Missing 'registers-number' property.\n");
return -EINVAL;
}
......
drivers/gpio/gpio-74xx-mmio.c
View file @ 8148c17b
......@@ -106,7 +106,6 @@ static int mmio_74xx_dir_out(struct gpio_chip *gc, unsigned int gpio, int val)
static int mmio_74xx_gpio_probe(struct platform_device *pdev)
{
struct mmio_74xx_gpio_priv *priv;
struct resource *res;
void __iomem *dat;
int err;
......@@ -116,8 +115,7 @@ static int mmio_74xx_gpio_probe(struct platform_device *pdev)
priv->flags = (uintptr_t)of_device_get_match_data(&pdev->dev);
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
dat = devm_ioremap_resource(&pdev->dev, res);
dat = devm_platform_ioremap_resource(pdev, 0);
if (IS_ERR(dat))
return PTR_ERR(dat);
......
drivers/gpio/gpio-amdpt.c
View file @ 8148c17b
......@@ -78,7 +78,6 @@ static int pt_gpio_probe(struct platform_device *pdev)
struct acpi_device *acpi_dev;
acpi_handle handle = ACPI_HANDLE(dev);
struct pt_gpio_chip *pt_gpio;
struct resource *res_mem;
int ret = 0;
if (acpi_bus_get_device(handle, &acpi_dev)) {
......@@ -90,12 +89,7 @@ static int pt_gpio_probe(struct platform_device *pdev)
if (!pt_gpio)
return -ENOMEM;
res_mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
if (!res_mem) {
dev_err(&pdev->dev, "Failed to get MMIO resource for PT GPIO.\n");
return -EINVAL;
}
pt_gpio->reg_base = devm_ioremap_resource(dev, res_mem);
pt_gpio->reg_base = devm_platform_ioremap_resource(pdev, 0);
if (IS_ERR(pt_gpio->reg_base)) {
dev_err(&pdev->dev, "Failed to map MMIO resource for PT GPIO.\n");
return PTR_ERR(pt_gpio->reg_base);
......
drivers/gpio/gpio-aspeed.c
View file @ 8148c17b
......@@ -1156,15 +1156,13 @@ static int __init aspeed_gpio_probe(struct platform_device *pdev)
{
const struct of_device_id *gpio_id;
struct aspeed_gpio *gpio;
struct resource *res;
int rc, i, banks;
gpio = devm_kzalloc(&pdev->dev, sizeof(*gpio), GFP_KERNEL);
if (!gpio)
return -ENOMEM;
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
gpio->base = devm_ioremap_resource(&pdev->dev, res);
gpio->base = devm_platform_ioremap_resource(pdev, 0);
if (IS_ERR(gpio->base))
return PTR_ERR(gpio->base);
......
drivers/gpio/gpio-bcm-kona.c
View file @ 8148c17b
......@@ -568,7 +568,6 @@ static int bcm_kona_gpio_probe(struct platform_device *pdev)
{
struct device *dev = &pdev->dev;
const struct of_device_id *match;
struct resource *res;
struct bcm_kona_gpio_bank *bank;
struct bcm_kona_gpio *kona_gpio;
struct gpio_chip *chip;
......@@ -618,8 +617,7 @@ static int bcm_kona_gpio_probe(struct platform_device *pdev)
return -ENXIO;
}
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
kona_gpio->reg_base = devm_ioremap_resource(dev, res);
kona_gpio->reg_base = devm_platform_ioremap_resource(pdev, 0);
if (IS_ERR(kona_gpio->reg_base)) {
ret = -ENXIO;
goto err_irq_domain;
......
drivers/gpio/gpio-cadence.c
View file @ 8148c17b
......@@ -148,7 +148,6 @@ static struct irq_chip cdns_gpio_irqchip = {
static int cdns_gpio_probe(struct platform_device *pdev)
{
struct cdns_gpio_chip *cgpio;
struct resource *res;
int ret, irq;
u32 dir_prev;
u32 num_gpios = 32;
......@@ -157,8 +156,7 @@ static int cdns_gpio_probe(struct platform_device *pdev)
if (!cgpio)
return -ENOMEM;
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
cgpio->regs = devm_ioremap_resource(&pdev->dev, res);
cgpio->regs = devm_platform_ioremap_resource(pdev, 0);
if (IS_ERR(cgpio->regs))
return PTR_ERR(cgpio->regs);
......
drivers/gpio/gpio-clps711x.c
View file @ 8148c17b
......@@ -19,7 +19,6 @@ static int clps711x_gpio_probe(struct platform_device *pdev)
struct device_node *np = pdev->dev.of_node;
void __iomem *dat, *dir;
struct gpio_chip *gc;
struct resource *res;
int err, id;
if (!np)
......@@ -33,13 +32,11 @@ static int clps711x_gpio_probe(struct platform_device *pdev)
if (!gc)
return -ENOMEM;
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
dat = devm_ioremap_resource(&pdev->dev, res);
dat = devm_platform_ioremap_resource(pdev, 0);
if (IS_ERR(dat))
return PTR_ERR(dat);
res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
dir = devm_ioremap_resource(&pdev->dev, res);
dir = devm_platform_ioremap_resource(pdev, 1);
if (IS_ERR(dir))
return PTR_ERR(dir);
......
drivers/gpio/gpio-dwapb.c
View file @ 8148c17b
......@@ -655,7 +655,6 @@ MODULE_DEVICE_TABLE(acpi, dwapb_acpi_match);
static int dwapb_gpio_probe(struct platform_device *pdev)
{
unsigned int i;
struct resource *res;
struct dwapb_gpio *gpio;
int err;
struct device *dev = &pdev->dev;
......@@ -688,8 +687,7 @@ static int dwapb_gpio_probe(struct platform_device *pdev)
if (!gpio->ports)
return -ENOMEM;
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
gpio->regs = devm_ioremap_resource(&pdev->dev, res);
gpio->regs = devm_platform_ioremap_resource(pdev, 0);
if (IS_ERR(gpio->regs))
return PTR_ERR(gpio->regs);
......
drivers/gpio/gpio-ftgpio010.c
View file @ 8148c17b
......@@ -225,7 +225,6 @@ static int ftgpio_gpio_set_config(struct gpio_chip *gc, unsigned int offset,
static int ftgpio_gpio_probe(struct platform_device *pdev)
{
struct device *dev = &pdev->dev;
struct resource *res;
struct ftgpio_gpio *g;
int irq;
int ret;
......@@ -236,8 +235,7 @@ static int ftgpio_gpio_probe(struct platform_device *pdev)
g->dev = dev;
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
g->base = devm_ioremap_resource(dev, res);
g->base = devm_platform_ioremap_resource(pdev, 0);
if (IS_ERR(g->base))
return PTR_ERR(g->base);
......
drivers/gpio/gpio-hlwd.c
View file @ 8148c17b
......@@ -208,7 +208,6 @@ static int hlwd_gpio_irq_set_type(struct irq_data *data, unsigned int flow_type)
static int hlwd_gpio_probe(struct platform_device *pdev)
{
struct hlwd_gpio *hlwd;
struct resource *regs_resource;
u32 ngpios;
int res;
......@@ -216,8 +215,7 @@ static int hlwd_gpio_probe(struct platform_device *pdev)
if (!hlwd)
return -ENOMEM;
regs_resource = platform_get_resource(pdev, IORESOURCE_MEM, 0);
hlwd->regs = devm_ioremap_resource(&pdev->dev, regs_resource);
hlwd->regs = devm_platform_ioremap_resource(pdev, 0);
if (IS_ERR(hlwd->regs))
return PTR_ERR(hlwd->regs);
......
drivers/gpio/gpio-iop.c
View file @ 8148c17b
......@@ -21,7 +21,6 @@
static int iop3xx_gpio_probe(struct platform_device *pdev)
{
struct resource *res;
struct gpio_chip *gc;
void __iomem *base;
int err;
......@@ -30,8 +29,7 @@ static int iop3xx_gpio_probe(struct platform_device *pdev)
if (!gc)
return -ENOMEM;
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
base = devm_ioremap_resource(&pdev->dev, res);
base = devm_platform_ioremap_resource(pdev, 0);
if (IS_ERR(base))
return PTR_ERR(base);
......
drivers/gpio/gpio-janz-ttl.c
View file @ 8148c17b
......@@ -147,7 +147,6 @@ static int ttl_probe(struct platform_device *pdev)
struct device *dev = &pdev->dev;
struct ttl_module *mod;
struct gpio_chip *gpio;
struct resource *res;
int ret;
pdata = dev_get_platdata(&pdev->dev);
......@@ -164,8 +163,7 @@ static int ttl_probe(struct platform_device *pdev)
spin_lock_init(&mod->lock);
/* get access to the MODULbus registers for this module */
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
mod->regs = devm_ioremap_resource(dev, res);
mod->regs = devm_platform_ioremap_resource(pdev, 0);
if (IS_ERR(mod->regs))
return PTR_ERR(mod->regs);
......
drivers/gpio/gpio-loongson1.c
View file @ 8148c17b
......@@ -47,15 +47,13 @@ static int ls1x_gpio_probe(struct platform_device *pdev)
{
struct device *dev = &pdev->dev;
struct gpio_chip *gc;
struct resource *res;
int ret;
gc = devm_kzalloc(dev, sizeof(*gc), GFP_KERNEL);
if (!gc)
return -ENOMEM;
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
gpio_reg_base = devm_ioremap_resource(dev, res);
gpio_reg_base = devm_platform_ioremap_resource(pdev, 0);
if (IS_ERR(gpio_reg_base))
return PTR_ERR(gpio_reg_base);
......
drivers/gpio/gpio-lpc18xx.c
View file @ 8148c17b
......@@ -340,10 +340,7 @@ static int lpc18xx_gpio_probe(struct platform_device *pdev)
index = of_property_match_string(dev->of_node, "reg-names", "gpio");
if (index < 0) {
/* To support backward compatibility take the first resource */
struct resource *res;
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
gc->base = devm_ioremap_resource(dev, res);
gc->base = devm_platform_ioremap_resource(pdev, 0);
} else {
struct resource res;
......
drivers/gpio/gpio-mb86s7x.c
View file @ 8148c17b
......@@ -146,7 +146,6 @@ static void mb86s70_gpio_set(struct gpio_chip *gc, unsigned gpio, int value)
static int mb86s70_gpio_probe(struct platform_device *pdev)
{
struct mb86s70_gpio_chip *gchip;
struct resource *res;
int ret;
gchip = devm_kzalloc(&pdev->dev, sizeof(*gchip), GFP_KERNEL);
......@@ -155,8 +154,7 @@ static int mb86s70_gpio_probe(struct platform_device *pdev)
platform_set_drvdata(pdev, gchip);
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
gchip->base = devm_ioremap_resource(&pdev->dev, res);
gchip->base = devm_platform_ioremap_resource(pdev, 0);
if (IS_ERR(gchip->base))
return PTR_ERR(gchip->base);
......
drivers/gpio/gpio-mlxbf.c 0 → 100644
View file @ 8148c17b
// SPDX-License-Identifier: GPL-2.0
#include <linux/acpi.h>
#include <linux/bitops.h>
#include <linux/device.h>
#include <linux/gpio/driver.h>
#include <linux/io.h>
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/platform_device.h>
#include <linux/pm.h>
#include <linux/resource.h>
#include <linux/types.h>
/* Number of pins on BlueField */
#define MLXBF_GPIO_NR 54
/* Pad Electrical Controls. */
#define MLXBF_GPIO_PAD_CONTROL_FIRST_WORD 0x0700
#define MLXBF_GPIO_PAD_CONTROL_1_FIRST_WORD 0x0708
#define MLXBF_GPIO_PAD_CONTROL_2_FIRST_WORD 0x0710
#define MLXBF_GPIO_PAD_CONTROL_3_FIRST_WORD 0x0718
#define MLXBF_GPIO_PIN_DIR_I 0x1040
#define MLXBF_GPIO_PIN_DIR_O 0x1048
#define MLXBF_GPIO_PIN_STATE 0x1000
#define MLXBF_GPIO_SCRATCHPAD 0x20
#ifdef CONFIG_PM
struct mlxbf_gpio_context_save_regs {
u64 scratchpad;
u64 pad_control[MLXBF_GPIO_NR];
u64 pin_dir_i;
u64 pin_dir_o;
};
#endif
/* Device state structure. */
struct mlxbf_gpio_state {
struct gpio_chip gc;
/* Memory Address */
void __iomem *base;
#ifdef CONFIG_PM
struct mlxbf_gpio_context_save_regs csave_regs;
#endif
};
static int mlxbf_gpio_probe(struct platform_device *pdev)
{
struct mlxbf_gpio_state *gs;
struct device *dev = &pdev->dev;
struct gpio_chip *gc;
int ret;
gs = devm_kzalloc(&pdev->dev, sizeof(*gs), GFP_KERNEL);
if (!gs)
return -ENOMEM;
gs->base = devm_platform_ioremap_resource(pdev, 0);
if (IS_ERR(gs->base))
return PTR_ERR(gs->base);
gc = &gs->gc;
ret = bgpio_init(gc, dev, 8,
gs->base + MLXBF_GPIO_PIN_STATE,
NULL,
NULL,
gs->base + MLXBF_GPIO_PIN_DIR_O,
gs->base + MLXBF_GPIO_PIN_DIR_I,
0);
if (ret)
return -ENODEV;
gc->owner = THIS_MODULE;
gc->ngpio = MLXBF_GPIO_NR;
ret = devm_gpiochip_add_data(dev, &gs->gc, gs);
if (ret) {
dev_err(&pdev->dev, "Failed adding memory mapped gpiochip\n");
return ret;
}
platform_set_drvdata(pdev, gs);
dev_info(&pdev->dev, "registered Mellanox BlueField GPIO");
return 0;
}
#ifdef CONFIG_PM
static int mlxbf_gpio_suspend(struct platform_device *pdev, pm_message_t state)
{
struct mlxbf_gpio_state *gs = platform_get_drvdata(pdev);
gs->csave_regs.scratchpad = readq(gs->base + MLXBF_GPIO_SCRATCHPAD);
gs->csave_regs.pad_control[0] =
readq(gs->base + MLXBF_GPIO_PAD_CONTROL_FIRST_WORD);
gs->csave_regs.pad_control[1] =
readq(gs->base + MLXBF_GPIO_PAD_CONTROL_1_FIRST_WORD);
gs->csave_regs.pad_control[2] =
readq(gs->base + MLXBF_GPIO_PAD_CONTROL_2_FIRST_WORD);
gs->csave_regs.pad_control[3] =
readq(gs->base + MLXBF_GPIO_PAD_CONTROL_3_FIRST_WORD);
gs->csave_regs.pin_dir_i = readq(gs->base + MLXBF_GPIO_PIN_DIR_I);
gs->csave_regs.pin_dir_o = readq(gs->base + MLXBF_GPIO_PIN_DIR_O);
return 0;
}
static int mlxbf_gpio_resume(struct platform_device *pdev)
{
struct mlxbf_gpio_state *gs = platform_get_drvdata(pdev);
writeq(gs->csave_regs.scratchpad, gs->base + MLXBF_GPIO_SCRATCHPAD);
writeq(gs->csave_regs.pad_control[0],
gs->base + MLXBF_GPIO_PAD_CONTROL_FIRST_WORD);
writeq(gs->csave_regs.pad_control[1],
gs->base + MLXBF_GPIO_PAD_CONTROL_1_FIRST_WORD);
writeq(gs->csave_regs.pad_control[2],
gs->base + MLXBF_GPIO_PAD_CONTROL_2_FIRST_WORD);
writeq(gs->csave_regs.pad_control[3],
gs->base + MLXBF_GPIO_PAD_CONTROL_3_FIRST_WORD);
writeq(gs->csave_regs.pin_dir_i, gs->base + MLXBF_GPIO_PIN_DIR_I);
writeq(gs->csave_regs.pin_dir_o, gs->base + MLXBF_GPIO_PIN_DIR_O);
return 0;
}
#endif
static const struct acpi_device_id mlxbf_gpio_acpi_match[] = {
{ "MLNXBF02", 0 },
{}
};
MODULE_DEVICE_TABLE(acpi, mlxbf_gpio_acpi_match);
static struct platform_driver mlxbf_gpio_driver = {
.driver = {
.name = "mlxbf_gpio",
.acpi_match_table = ACPI_PTR(mlxbf_gpio_acpi_match),
},
.probe = mlxbf_gpio_probe,
#ifdef CONFIG_PM
.suspend = mlxbf_gpio_suspend,
.resume = mlxbf_gpio_resume,
#endif
};
module_platform_driver(mlxbf_gpio_driver);
MODULE_DESCRIPTION("Mellanox BlueField GPIO Driver");
MODULE_AUTHOR("Mellanox Technologies");
MODULE_LICENSE("GPL");
drivers/gpio/gpio-mmio.c
View file @ 8148c17b
......@@ -134,17 +134,6 @@ static int bgpio_get_set(struct gpio_chip *gc, unsigned int gpio)
unsigned long pinmask = bgpio_line2mask(gc, gpio);
bool dir = !!(gc->bgpio_dir & pinmask);
/*
* If the direction is OUT we read the value from the SET
* register, and if the direction is IN we read the value
* from the DAT register.
*
* If the direction bits are inverted, naturally this gets
* inverted too.
*/
if (gc->bgpio_dir_inverted)
dir = !dir;
if (dir)
return !!(gc->read_reg(gc->reg_set) & pinmask);
else
......@@ -164,14 +153,8 @@ static int bgpio_get_set_multiple(struct gpio_chip *gc, unsigned long *mask,
/* Make sure we first clear any bits that are zero when we read the register */
*bits &= ~*mask;
/* Exploit the fact that we know which directions are set */
if (gc->bgpio_dir_inverted) {
set_mask = *mask & ~gc->bgpio_dir;
get_mask = *mask & gc->bgpio_dir;
} else {
set_mask = *mask & gc->bgpio_dir;
get_mask = *mask & ~gc->bgpio_dir;
}
set_mask = *mask & gc->bgpio_dir;
get_mask = *mask & ~gc->bgpio_dir;
if (set_mask)
*bits |= gc->read_reg(gc->reg_set) & set_mask;
......@@ -372,11 +355,12 @@ static int bgpio_dir_in(struct gpio_chip *gc, unsigned int gpio)
spin_lock_irqsave(&gc->bgpio_lock, flags);
if (gc->bgpio_dir_inverted)
gc->bgpio_dir |= bgpio_line2mask(gc, gpio);
else
gc->bgpio_dir &= ~bgpio_line2mask(gc, gpio);
gc->write_reg(gc->reg_dir, gc->bgpio_dir);
gc->bgpio_dir &= ~bgpio_line2mask(gc, gpio);
if (gc->reg_dir_in)
gc->write_reg(gc->reg_dir_in, ~gc->bgpio_dir);
if (gc->reg_dir_out)
gc->write_reg(gc->reg_dir_out, gc->bgpio_dir);
spin_unlock_irqrestore(&gc->bgpio_lock, flags);
......@@ -385,11 +369,16 @@ static int bgpio_dir_in(struct gpio_chip *gc, unsigned int gpio)
static int bgpio_get_dir(struct gpio_chip *gc, unsigned int gpio)
{
/* Return 0 if output, 1 of input */
if (gc->bgpio_dir_inverted)
return !!(gc->read_reg(gc->reg_dir) & bgpio_line2mask(gc, gpio));
else
return !(gc->read_reg(gc->reg_dir) & bgpio_line2mask(gc, gpio));
/* Return 0 if output, 1 if input */
if (gc->bgpio_dir_unreadable)
return !(gc->bgpio_dir & bgpio_line2mask(gc, gpio));
if (gc->reg_dir_out)
return !(gc->read_reg(gc->reg_dir_out) & bgpio_line2mask(gc, gpio));
if (gc->reg_dir_in)
return !!(gc->read_reg(gc->reg_dir_in) & bgpio_line2mask(gc, gpio));
/* This should not happen */
return 1;
}
static int bgpio_dir_out(struct gpio_chip *gc, unsigned int gpio, int val)
......@@ -400,11 +389,12 @@ static int bgpio_dir_out(struct gpio_chip *gc, unsigned int gpio, int val)
spin_lock_irqsave(&gc->bgpio_lock, flags);
if (gc->bgpio_dir_inverted)
gc->bgpio_dir &= ~bgpio_line2mask(gc, gpio);
else
gc->bgpio_dir |= bgpio_line2mask(gc, gpio);
gc->write_reg(gc->reg_dir, gc->bgpio_dir);
gc->bgpio_dir |= bgpio_line2mask(gc, gpio);
if (gc->reg_dir_in)
gc->write_reg(gc->reg_dir_in, ~gc->bgpio_dir);
if (gc->reg_dir_out)
gc->write_reg(gc->reg_dir_out, gc->bgpio_dir);
spin_unlock_irqrestore(&gc->bgpio_lock, flags);
......@@ -537,19 +527,12 @@ static int bgpio_setup_direction(struct gpio_chip *gc,
void __iomem *dirin,
unsigned long flags)
{
if (dirout && dirin) {
return -EINVAL;
} else if (dirout) {
gc->reg_dir = dirout;
gc->direction_output = bgpio_dir_out;
gc->direction_input = bgpio_dir_in;
gc->get_direction = bgpio_get_dir;
} else if (dirin) {
gc->reg_dir = dirin;
if (dirout || dirin) {
gc->reg_dir_out = dirout;
gc->reg_dir_in = dirin;
gc->direction_output = bgpio_dir_out;
gc->direction_input = bgpio_dir_in;
gc->get_direction = bgpio_get_dir;
gc->bgpio_dir_inverted = true;
} else {
if (flags & BGPIOF_NO_OUTPUT)
gc->direction_output = bgpio_dir_out_err;
......@@ -588,11 +571,11 @@ static int bgpio_request(struct gpio_chip *chip, unsigned gpio_pin)
* @dirout: MMIO address for the register to set the line as OUTPUT. It is assumed
* that setting a line to 1 in this register will turn that line into an
* output line. Conversely, setting the line to 0 will turn that line into
* an input. Either this or @dirin can be defined, but never both.
* an input.
* @dirin: MMIO address for the register to set this line as INPUT. It is assumed
* that setting a line to 1 in this register will turn that line into an
* input line. Conversely, setting the line to 0 will turn that line into
* an output. Either this or @dirout can be defined, but never both.
* an output.
* @flags: Different flags that will affect the behaviour of the device, such as
* endianness etc.
*/
......@@ -634,8 +617,28 @@ int bgpio_init(struct gpio_chip *gc, struct device *dev,
if (gc->set == bgpio_set_set &&
!(flags & BGPIOF_UNREADABLE_REG_SET))
gc->bgpio_data = gc->read_reg(gc->reg_set);
if (gc->reg_dir && !(flags & BGPIOF_UNREADABLE_REG_DIR))
gc->bgpio_dir = gc->read_reg(gc->reg_dir);
if (flags & BGPIOF_UNREADABLE_REG_DIR)
gc->bgpio_dir_unreadable = true;
/*
* Inspect hardware to find initial direction setting.
*/
if ((gc->reg_dir_out || gc->reg_dir_in) &&
!(flags & BGPIOF_UNREADABLE_REG_DIR)) {
if (gc->reg_dir_out)
gc->bgpio_dir = gc->read_reg(gc->reg_dir_out);
else if (gc->reg_dir_in)
gc->bgpio_dir = ~gc->read_reg(gc->reg_dir_in);
/*
* If we have two direction registers, synchronise
* input setting to output setting, the library
* can not handle a line being input and output at
* the same time.
*/
if (gc->reg_dir_out && gc->reg_dir_in)
gc->write_reg(gc->reg_dir_in, ~gc->bgpio_dir);
}
return ret;
}
......
drivers/gpio/gpio-mt7621.c
View file @ 8148c17b
......@@ -293,7 +293,6 @@ mediatek_gpio_bank_probe(struct device *dev,
static int
mediatek_gpio_probe(struct platform_device *pdev)
{
struct resource *res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
struct device *dev = &pdev->dev;
struct device_node *np = dev->of_node;
struct mtk *mtk;
......@@ -304,7 +303,7 @@ mediatek_gpio_probe(struct platform_device *pdev)
if (!mtk)
return -ENOMEM;
mtk->base = devm_ioremap_resource(dev, res);
mtk->base = devm_platform_ioremap_resource(pdev, 0);
if (IS_ERR(mtk->base))
return PTR_ERR(mtk->base);
......
drivers/gpio/gpio-mvebu.c
View file @ 8148c17b
......@@ -1038,11 +1038,9 @@ static const struct regmap_config mvebu_gpio_regmap_config = {
static int mvebu_gpio_probe_raw(struct platform_device *pdev,
struct mvebu_gpio_chip *mvchip)
{
struct resource *res;
void __iomem *base;
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
base = devm_ioremap_resource(&pdev->dev, res);
base = devm_platform_ioremap_resource(pdev, 0);
if (IS_ERR(base))
return PTR_ERR(base);
......@@ -1062,8 +1060,7 @@ static int mvebu_gpio_probe_raw(struct platform_device *pdev,
* per-CPU registers
*/
if (mvchip->soc_variant == MVEBU_GPIO_SOC_VARIANT_ARMADAXP) {
res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
base = devm_ioremap_resource(&pdev->dev, res);
base = devm_platform_ioremap_resource(pdev, 1);
if (IS_ERR(base))
return PTR_ERR(base);
......
drivers/gpio/gpio-mxc.c
View file @ 8148c17b
......@@ -411,7 +411,6 @@ static int mxc_gpio_probe(struct platform_device *pdev)
{
struct device_node *np = pdev->dev.of_node;
struct mxc_gpio_port *port;
struct resource *iores;
int irq_base;
int err;
......@@ -423,8 +422,7 @@ static int mxc_gpio_probe(struct platform_device *pdev)
port->dev = &pdev->dev;
iores = platform_get_resource(pdev, IORESOURCE_MEM, 0);
port->base = devm_ioremap_resource(&pdev->dev, iores);
port->base = devm_platform_ioremap_resource(pdev, 0);
if (IS_ERR(port->base))
return PTR_ERR(port->base);
......
drivers/gpio/gpio-octeon.c
View file @ 8148c17b
......@@ -82,7 +82,6 @@ static int octeon_gpio_probe(struct platform_device *pdev)
{
struct octeon_gpio *gpio;
struct gpio_chip *chip;
struct resource *res_mem;
void __iomem *reg_base;
int err = 0;
......@@ -91,8 +90,7 @@ static int octeon_gpio_probe(struct platform_device *pdev)
return -ENOMEM;
chip = &gpio->chip;
res_mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
reg_base = devm_ioremap_resource(&pdev->dev, res_mem);
reg_base = devm_platform_ioremap_resource(pdev, 0);
if (IS_ERR(reg_base))
return PTR_ERR(reg_base);
......
drivers/gpio/gpio-omap.c
View file @ 8148c17b
......@@ -31,8 +31,6 @@
#define OMAP4_GPIO_DEBOUNCINGTIME_MASK 0xFF
#define OMAP_GPIO_QUIRK_IDLE_REMOVE_TRIGGER BIT(2)
struct gpio_regs {
u32 irqenable1;
u32 irqenable2;
......@@ -48,13 +46,6 @@ struct gpio_regs {
u32 debounce_en;
};
struct gpio_bank;
struct gpio_omap_funcs {
void (*idle_enable_level_quirk)(struct gpio_bank *bank);
void (*idle_disable_level_quirk)(struct gpio_bank *bank);
};
struct gpio_bank {
struct list_head node;
void __iomem *base;
......@@ -62,7 +53,6 @@ struct gpio_bank {
u32 non_wakeup_gpios;
u32 enabled_non_wakeup_gpios;
struct gpio_regs context;
struct gpio_omap_funcs funcs;
u32 saved_datain;
u32 level_mask;
u32 toggle_mask;
......@@ -83,8 +73,6 @@ struct gpio_bank {
int stride;
u32 width;
int context_loss_count;
bool workaround_enabled;
u32 quirks;
void (*set_dataout)(struct gpio_bank *bank, unsigned gpio, int enable);
void (*set_dataout_multiple)(struct gpio_bank *bank,
......@@ -353,6 +341,22 @@ static void omap_clear_gpio_debounce(struct gpio_bank *bank, unsigned offset)
}
}
/*
* Off mode wake-up capable GPIOs in bank(s) that are in the wakeup domain.
* See TRM section for GPIO for "Wake-Up Generation" for the list of GPIOs
* in wakeup domain. If bank->non_wakeup_gpios is not configured, assume none
* are capable waking up the system from off mode.
*/
static bool omap_gpio_is_off_wakeup_capable(struct gpio_bank *bank, u32 gpio_mask)
{
u32 no_wake = bank->non_wakeup_gpios;
if (no_wake)
return !!(~no_wake & gpio_mask);
return false;
}
static inline void omap_set_gpio_trigger(struct gpio_bank *bank, int gpio,
unsigned trigger)
{
......@@ -363,10 +367,16 @@ static inline void omap_set_gpio_trigger(struct gpio_bank *bank, int gpio,
trigger & IRQ_TYPE_LEVEL_LOW);
omap_gpio_rmw(base, bank->regs->leveldetect1, gpio_bit,
trigger & IRQ_TYPE_LEVEL_HIGH);
/*
* We need the edge detection enabled for to allow the GPIO block
* to be woken from idle state. Set the appropriate edge detection
* in addition to the level detection.
*/
omap_gpio_rmw(base, bank->regs->risingdetect, gpio_bit,
trigger & IRQ_TYPE_EDGE_RISING);
trigger & (IRQ_TYPE_EDGE_RISING | IRQ_TYPE_LEVEL_HIGH));
omap_gpio_rmw(base, bank->regs->fallingdetect, gpio_bit,
trigger & IRQ_TYPE_EDGE_FALLING);
trigger & (IRQ_TYPE_EDGE_FALLING | IRQ_TYPE_LEVEL_LOW));
bank->context.leveldetect0 =
readl_relaxed(bank->base + bank->regs->leveldetect0);
......@@ -384,13 +394,7 @@ static inline void omap_set_gpio_trigger(struct gpio_bank *bank, int gpio,
}
/* This part needs to be executed always for OMAP{34xx, 44xx} */
if (!bank->regs->irqctrl) {
/* On omap24xx proceed only when valid GPIO bit is set */
if (bank->non_wakeup_gpios) {
if (!(bank->non_wakeup_gpios & gpio_bit))
goto exit;
}
if (!bank->regs->irqctrl && !omap_gpio_is_off_wakeup_capable(bank, gpio)) {
/*
* Log the edge gpio and manually trigger the IRQ
* after resume if the input level changes
......@@ -403,7 +407,6 @@ static inline void omap_set_gpio_trigger(struct gpio_bank *bank, int gpio,
bank->enabled_non_wakeup_gpios &= ~gpio_bit;
}
exit:
bank->level_mask =
readl_relaxed(bank->base + bank->regs->leveldetect0) |
readl_relaxed(bank->base + bank->regs->leveldetect1);
......@@ -896,44 +899,6 @@ static void omap_gpio_unmask_irq(struct irq_data *d)
raw_spin_unlock_irqrestore(&bank->lock, flags);
}
/*
* Only edges can generate a wakeup event to the PRCM.
*
* Therefore, ensure any wake-up capable GPIOs have
* edge-detection enabled before going idle to ensure a wakeup
* to the PRCM is generated on a GPIO transition. (c.f. 34xx
* NDA TRM 25.5.3.1)
*
* The normal values will be restored upon ->runtime_resume()
* by writing back the values saved in bank->context.
*/
static void __maybe_unused
omap2_gpio_enable_level_quirk(struct gpio_bank *bank)
{
u32 wake_low, wake_hi;
/* Enable additional edge detection for level gpios for idle */
wake_low = bank->context.leveldetect0 & bank->context.wake_en;
if (wake_low)
writel_relaxed(wake_low | bank->context.fallingdetect,
bank->base + bank->regs->fallingdetect);
wake_hi = bank->context.leveldetect1 & bank->context.wake_en;
if (wake_hi)
writel_relaxed(wake_hi | bank->context.risingdetect,
bank->base + bank->regs->risingdetect);
}
static void __maybe_unused
omap2_gpio_disable_level_quirk(struct gpio_bank *bank)
{
/* Disable edge detection for level gpios after idle */
writel_relaxed(bank->context.fallingdetect,
bank->base + bank->regs->fallingdetect);
writel_relaxed(bank->context.risingdetect,
bank->base + bank->regs->risingdetect);
}
/*---------------------------------------------------------------------*/
static int omap_mpuio_suspend_noirq(struct device *dev)
......@@ -1251,203 +1216,70 @@ static int omap_gpio_chip_init(struct gpio_bank *bank, struct irq_chip *irqc)
return ret;
}
static void omap_gpio_idle(struct gpio_bank *bank, bool may_lose_context);
static void omap_gpio_unidle(struct gpio_bank *bank);
static int gpio_omap_cpu_notifier(struct notifier_block *nb,
unsigned long cmd, void *v)
static void omap_gpio_init_context(struct gpio_bank *p)
{
struct gpio_bank *bank;
unsigned long flags;
struct omap_gpio_reg_offs *regs = p->regs;
void __iomem *base = p->base;
bank = container_of(nb, struct gpio_bank, nb);
p->context.ctrl = readl_relaxed(base + regs->ctrl);
p->context.oe = readl_relaxed(base + regs->direction);
p->context.wake_en = readl_relaxed(base + regs->wkup_en);
p->context.leveldetect0 = readl_relaxed(base + regs->leveldetect0);
p->context.leveldetect1 = readl_relaxed(base + regs->leveldetect1);
p->context.risingdetect = readl_relaxed(base + regs->risingdetect);
p->context.fallingdetect = readl_relaxed(base + regs->fallingdetect);
p->context.irqenable1 = readl_relaxed(base + regs->irqenable);
p->context.irqenable2 = readl_relaxed(base + regs->irqenable2);
raw_spin_lock_irqsave(&bank->lock, flags);
switch (cmd) {
case CPU_CLUSTER_PM_ENTER:
if (bank->is_suspended)
break;
omap_gpio_idle(bank, true);
break;
case CPU_CLUSTER_PM_ENTER_FAILED:
case CPU_CLUSTER_PM_EXIT:
if (bank->is_suspended)
break;
omap_gpio_unidle(bank);
break;
}
raw_spin_unlock_irqrestore(&bank->lock, flags);
if (regs->set_dataout && p->regs->clr_dataout)
p->context.dataout = readl_relaxed(base + regs->set_dataout);
else
p->context.dataout = readl_relaxed(base + regs->dataout);
return NOTIFY_OK;
p->context_valid = true;
}
static const struct of_device_id omap_gpio_match[];
static int omap_gpio_probe(struct platform_device *pdev)
static void omap_gpio_restore_context(struct gpio_bank *bank)
{
struct device *dev = &pdev->dev;
struct device_node *node = dev->of_node;
const struct of_device_id *match;
const struct omap_gpio_platform_data *pdata;
struct resource *res;
struct gpio_bank *bank;
struct irq_chip *irqc;
int ret;
match = of_match_device(of_match_ptr(omap_gpio_match), dev);
pdata = match ? match->data : dev_get_platdata(dev);
if (!pdata)
return -EINVAL;
bank = devm_kzalloc(dev, sizeof(*bank), GFP_KERNEL);
if (!bank)
return -ENOMEM;
irqc = devm_kzalloc(dev, sizeof(*irqc), GFP_KERNEL);
if (!irqc)
return -ENOMEM;
irqc->irq_startup = omap_gpio_irq_startup,
irqc->irq_shutdown = omap_gpio_irq_shutdown,
irqc->irq_ack = omap_gpio_ack_irq,
irqc->irq_mask = omap_gpio_mask_irq,
irqc->irq_unmask = omap_gpio_unmask_irq,
irqc->irq_set_type = omap_gpio_irq_type,
irqc->irq_set_wake = omap_gpio_wake_enable,
irqc->irq_bus_lock = omap_gpio_irq_bus_lock,
irqc->irq_bus_sync_unlock = gpio_irq_bus_sync_unlock,
irqc->name = dev_name(&pdev->dev);
irqc->flags = IRQCHIP_MASK_ON_SUSPEND;
irqc->parent_device = dev;
bank->irq = platform_get_irq(pdev, 0);
if (bank->irq <= 0) {
if (!bank->irq)
bank->irq = -ENXIO;
if (bank->irq != -EPROBE_DEFER)
dev_err(dev,
"can't get irq resource ret=%d\n", bank->irq);
return bank->irq;
}
bank->chip.parent = dev;
bank->chip.owner = THIS_MODULE;
bank->dbck_flag = pdata->dbck_flag;
bank->quirks = pdata->quirks;
bank->stride = pdata->bank_stride;
bank->width = pdata->bank_width;
bank->is_mpuio = pdata->is_mpuio;
bank->non_wakeup_gpios = pdata->non_wakeup_gpios;
bank->regs = pdata->regs;
#ifdef CONFIG_OF_GPIO
bank->chip.of_node = of_node_get(node);
#endif
if (node) {
if (!of_property_read_bool(node, "ti,gpio-always-on"))
bank->loses_context = true;
} else {
bank->loses_context = pdata->loses_context;
if (bank->loses_context)
bank->get_context_loss_count =
pdata->get_context_loss_count;
}
if (bank->regs->set_dataout && bank->regs->clr_dataout) {
bank->set_dataout = omap_set_gpio_dataout_reg;
bank->set_dataout_multiple = omap_set_gpio_dataout_reg_multiple;
} else {
bank->set_dataout = omap_set_gpio_dataout_mask;
bank->set_dataout_multiple =
omap_set_gpio_dataout_mask_multiple;
}
if (bank->quirks & OMAP_GPIO_QUIRK_IDLE_REMOVE_TRIGGER) {
bank->funcs.idle_enable_level_quirk =
omap2_gpio_enable_level_quirk;
bank->funcs.idle_disable_level_quirk =
omap2_gpio_disable_level_quirk;
}
raw_spin_lock_init(&bank->lock);
raw_spin_lock_init(&bank->wa_lock);
/* Static mapping, never released */
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
bank->base = devm_ioremap_resource(dev, res);
if (IS_ERR(bank->base)) {
return PTR_ERR(bank->base);
}
if (bank->dbck_flag) {
bank->dbck = devm_clk_get(dev, "dbclk");
if (IS_ERR(bank->dbck)) {
dev_err(dev,
"Could not get gpio dbck. Disable debounce\n");
bank->dbck_flag = false;
} else {
clk_prepare(bank->dbck);
}
}
platform_set_drvdata(pdev, bank);
pm_runtime_enable(dev);
pm_runtime_get_sync(dev);
if (bank->is_mpuio)
omap_mpuio_init(bank);
omap_gpio_mod_init(bank);
ret = omap_gpio_chip_init(bank, irqc);
if (ret) {
pm_runtime_put_sync(dev);
pm_runtime_disable(dev);
if (bank->dbck_flag)
clk_unprepare(bank->dbck);
return ret;
}
omap_gpio_show_rev(bank);
writel_relaxed(bank->context.wake_en,
bank->base + bank->regs->wkup_en);
writel_relaxed(bank->context.ctrl, bank->base + bank->regs->ctrl);
writel_relaxed(bank->context.leveldetect0,
bank->base + bank->regs->leveldetect0);
writel_relaxed(bank->context.leveldetect1,
bank->base + bank->regs->leveldetect1);
writel_relaxed(bank->context.risingdetect,
bank->base + bank->regs->risingdetect);
writel_relaxed(bank->context.fallingdetect,
bank->base + bank->regs->fallingdetect);
if (bank->regs->set_dataout && bank->regs->clr_dataout)
writel_relaxed(bank->context.dataout,
bank->base + bank->regs->set_dataout);
else
writel_relaxed(bank->context.dataout,
bank->base + bank->regs->dataout);
writel_relaxed(bank->context.oe, bank->base + bank->regs->direction);
if (bank->funcs.idle_enable_level_quirk &&
bank->funcs.idle_disable_level_quirk) {
bank->nb.notifier_call = gpio_omap_cpu_notifier;
cpu_pm_register_notifier(&bank->nb);
if (bank->dbck_enable_mask) {
writel_relaxed(bank->context.debounce, bank->base +
bank->regs->debounce);
writel_relaxed(bank->context.debounce_en,
bank->base + bank->regs->debounce_en);
}
pm_runtime_put(dev);
return 0;
}
static int omap_gpio_remove(struct platform_device *pdev)
{
struct gpio_bank *bank = platform_get_drvdata(pdev);
if (bank->nb.notifier_call)
cpu_pm_unregister_notifier(&bank->nb);
list_del(&bank->node);
gpiochip_remove(&bank->chip);
pm_runtime_disable(&pdev->dev);
if (bank->dbck_flag)
clk_unprepare(bank->dbck);
return 0;
writel_relaxed(bank->context.irqenable1,
bank->base + bank->regs->irqenable);
writel_relaxed(bank->context.irqenable2,
bank->base + bank->regs->irqenable2);
}
static void omap_gpio_restore_context(struct gpio_bank *bank);
static void omap_gpio_idle(struct gpio_bank *bank, bool may_lose_context)
{
struct device *dev = bank->chip.parent;
u32 l1 = 0, l2 = 0;
void __iomem *base = bank->base;
u32 nowake;
if (bank->funcs.idle_enable_level_quirk)
bank->funcs.idle_enable_level_quirk(bank);
bank->saved_datain = readl_relaxed(base + bank->regs->datain);
if (!bank->enabled_non_wakeup_gpios)
goto update_gpio_context_count;
......@@ -1456,22 +1288,15 @@ static void omap_gpio_idle(struct gpio_bank *bank, bool may_lose_context)
goto update_gpio_context_count;
/*
* If going to OFF, remove triggering for all
* If going to OFF, remove triggering for all wkup domain
* non-wakeup GPIOs. Otherwise spurious IRQs will be
* generated. See OMAP2420 Errata item 1.101.
*/
bank->saved_datain = readl_relaxed(bank->base +
bank->regs->datain);
l1 = bank->context.fallingdetect;
l2 = bank->context.risingdetect;
l1 &= ~bank->enabled_non_wakeup_gpios;
l2 &= ~bank->enabled_non_wakeup_gpios;
writel_relaxed(l1, bank->base + bank->regs->fallingdetect);
writel_relaxed(l2, bank->base + bank->regs->risingdetect);
bank->workaround_enabled = true;
if (!bank->loses_context && bank->enabled_non_wakeup_gpios) {
nowake = bank->enabled_non_wakeup_gpios;
omap_gpio_rmw(base, bank->regs->fallingdetect, nowake, ~nowake);
omap_gpio_rmw(base, bank->regs->risingdetect, nowake, ~nowake);
}
update_gpio_context_count:
if (bank->get_context_loss_count)
......@@ -1481,8 +1306,6 @@ static void omap_gpio_idle(struct gpio_bank *bank, bool may_lose_context)
omap_gpio_dbck_disable(bank);
}
static void omap_gpio_init_context(struct gpio_bank *p);
static void omap_gpio_unidle(struct gpio_bank *bank)
{
struct device *dev = bank->chip.parent;
......@@ -1504,9 +1327,6 @@ static void omap_gpio_unidle(struct gpio_bank *bank)
omap_gpio_dbck_enable(bank);
if (bank->funcs.idle_disable_level_quirk)
bank->funcs.idle_disable_level_quirk(bank);
if (bank->loses_context) {
if (!bank->get_context_loss_count) {
omap_gpio_restore_context(bank);
......@@ -1518,11 +1338,14 @@ static void omap_gpio_unidle(struct gpio_bank *bank)
return;
}
}
} else {
/* Restore changes done for OMAP2420 errata 1.101 */
writel_relaxed(bank->context.fallingdetect,
bank->base + bank->regs->fallingdetect);
writel_relaxed(bank->context.risingdetect,
bank->base + bank->regs->risingdetect);
}
if (!bank->workaround_enabled)
return;
l = readl_relaxed(bank->base + bank->regs->datain);
/*
......@@ -1572,117 +1395,35 @@ static void omap_gpio_unidle(struct gpio_bank *bank)
writel_relaxed(old0, bank->base + bank->regs->leveldetect0);
writel_relaxed(old1, bank->base + bank->regs->leveldetect1);
}
bank->workaround_enabled = false;
}
static void omap_gpio_init_context(struct gpio_bank *p)
static int gpio_omap_cpu_notifier(struct notifier_block *nb,
unsigned long cmd, void *v)
{
struct omap_gpio_reg_offs *regs = p->regs;
void __iomem *base = p->base;
p->context.ctrl = readl_relaxed(base + regs->ctrl);
p->context.oe = readl_relaxed(base + regs->direction);
p->context.wake_en = readl_relaxed(base + regs->wkup_en);
p->context.leveldetect0 = readl_relaxed(base + regs->leveldetect0);
p->context.leveldetect1 = readl_relaxed(base + regs->leveldetect1);
p->context.risingdetect = readl_relaxed(base + regs->risingdetect);
p->context.fallingdetect = readl_relaxed(base + regs->fallingdetect);
p->context.irqenable1 = readl_relaxed(base + regs->irqenable);
p->context.irqenable2 = readl_relaxed(base + regs->irqenable2);
if (regs->set_dataout && p->regs->clr_dataout)
p->context.dataout = readl_relaxed(base + regs->set_dataout);
else
p->context.dataout = readl_relaxed(base + regs->dataout);
p->context_valid = true;
}
static void omap_gpio_restore_context(struct gpio_bank *bank)
{
writel_relaxed(bank->context.wake_en,
bank->base + bank->regs->wkup_en);
writel_relaxed(bank->context.ctrl, bank->base + bank->regs->ctrl);
writel_relaxed(bank->context.leveldetect0,
bank->base + bank->regs->leveldetect0);
writel_relaxed(bank->context.leveldetect1,
bank->base + bank->regs->leveldetect1);
writel_relaxed(bank->context.risingdetect,
bank->base + bank->regs->risingdetect);
writel_relaxed(bank->context.fallingdetect,
bank->base + bank->regs->fallingdetect);
if (bank->regs->set_dataout && bank->regs->clr_dataout)
writel_relaxed(bank->context.dataout,
bank->base + bank->regs->set_dataout);
else
writel_relaxed(bank->context.dataout,
bank->base + bank->regs->dataout);
writel_relaxed(bank->context.oe, bank->base + bank->regs->direction);
if (bank->dbck_enable_mask) {
writel_relaxed(bank->context.debounce, bank->base +
bank->regs->debounce);
writel_relaxed(bank->context.debounce_en,
bank->base + bank->regs->debounce_en);
}
writel_relaxed(bank->context.irqenable1,
bank->base + bank->regs->irqenable);
writel_relaxed(bank->context.irqenable2,
bank->base + bank->regs->irqenable2);
}
static int __maybe_unused omap_gpio_runtime_suspend(struct device *dev)
{
struct gpio_bank *bank = dev_get_drvdata(dev);
struct gpio_bank *bank;
unsigned long flags;
int error = 0;
raw_spin_lock_irqsave(&bank->lock, flags);
/* Must be idled only by CPU_CLUSTER_PM_ENTER? */
if (bank->irq_usage) {
error = -EBUSY;
goto unlock;
}
omap_gpio_idle(bank, true);
bank->is_suspended = true;
unlock:
raw_spin_unlock_irqrestore(&bank->lock, flags);
return error;
}
static int __maybe_unused omap_gpio_runtime_resume(struct device *dev)
{
struct gpio_bank *bank = dev_get_drvdata(dev);
unsigned long flags;
int error = 0;
bank = container_of(nb, struct gpio_bank, nb);
raw_spin_lock_irqsave(&bank->lock, flags);
/* Must be unidled only by CPU_CLUSTER_PM_ENTER? */
if (bank->irq_usage) {
error = -EBUSY;
goto unlock;
switch (cmd) {
case CPU_CLUSTER_PM_ENTER:
if (bank->is_suspended)
break;
omap_gpio_idle(bank, true);
break;
case CPU_CLUSTER_PM_ENTER_FAILED:
case CPU_CLUSTER_PM_EXIT:
if (bank->is_suspended)
break;
omap_gpio_unidle(bank);
break;
}
omap_gpio_unidle(bank);
bank->is_suspended = false;
unlock:
raw_spin_unlock_irqrestore(&bank->lock, flags);
return error;
return NOTIFY_OK;
}
#ifdef CONFIG_ARCH_OMAP2PLUS
static const struct dev_pm_ops gpio_pm_ops = {
SET_RUNTIME_PM_OPS(omap_gpio_runtime_suspend, omap_gpio_runtime_resume,
NULL)
};
#else
static const struct dev_pm_ops gpio_pm_ops;
#endif /* CONFIG_ARCH_OMAP2PLUS */
#if defined(CONFIG_OF)
static struct omap_gpio_reg_offs omap2_gpio_regs = {
.revision = OMAP24XX_GPIO_REVISION,
.direction = OMAP24XX_GPIO_OE,
......@@ -1729,11 +1470,6 @@ static struct omap_gpio_reg_offs omap4_gpio_regs = {
.fallingdetect = OMAP4_GPIO_FALLINGDETECT,
};
/*
* Note that omap2 does not currently support idle modes with context loss so
* no need to add OMAP_GPIO_QUIRK_IDLE_REMOVE_TRIGGER quirk flag to save
* and restore context.
*/
static const struct omap_gpio_platform_data omap2_pdata = {
.regs = &omap2_gpio_regs,
.bank_width = 32,
......@@ -1744,14 +1480,12 @@ static const struct omap_gpio_platform_data omap3_pdata = {
.regs = &omap2_gpio_regs,
.bank_width = 32,
.dbck_flag = true,
.quirks = OMAP_GPIO_QUIRK_IDLE_REMOVE_TRIGGER,
};
static const struct omap_gpio_platform_data omap4_pdata = {
.regs = &omap4_gpio_regs,
.bank_width = 32,
.dbck_flag = true,
.quirks = OMAP_GPIO_QUIRK_IDLE_REMOVE_TRIGGER,
};
static const struct of_device_id omap_gpio_match[] = {
......@@ -1770,15 +1504,187 @@ static const struct of_device_id omap_gpio_match[] = {
{ },
};
MODULE_DEVICE_TABLE(of, omap_gpio_match);
static int omap_gpio_probe(struct platform_device *pdev)
{
struct device *dev = &pdev->dev;
struct device_node *node = dev->of_node;
const struct of_device_id *match;
const struct omap_gpio_platform_data *pdata;
struct gpio_bank *bank;
struct irq_chip *irqc;
int ret;
match = of_match_device(of_match_ptr(omap_gpio_match), dev);
pdata = match ? match->data : dev_get_platdata(dev);
if (!pdata)
return -EINVAL;
bank = devm_kzalloc(dev, sizeof(*bank), GFP_KERNEL);
if (!bank)
return -ENOMEM;
irqc = devm_kzalloc(dev, sizeof(*irqc), GFP_KERNEL);
if (!irqc)
return -ENOMEM;
irqc->irq_startup = omap_gpio_irq_startup,
irqc->irq_shutdown = omap_gpio_irq_shutdown,
irqc->irq_ack = omap_gpio_ack_irq,
irqc->irq_mask = omap_gpio_mask_irq,
irqc->irq_unmask = omap_gpio_unmask_irq,
irqc->irq_set_type = omap_gpio_irq_type,
irqc->irq_set_wake = omap_gpio_wake_enable,
irqc->irq_bus_lock = omap_gpio_irq_bus_lock,
irqc->irq_bus_sync_unlock = gpio_irq_bus_sync_unlock,
irqc->name = dev_name(&pdev->dev);
irqc->flags = IRQCHIP_MASK_ON_SUSPEND;
irqc->parent_device = dev;
bank->irq = platform_get_irq(pdev, 0);
if (bank->irq <= 0) {
if (!bank->irq)
bank->irq = -ENXIO;
if (bank->irq != -EPROBE_DEFER)
dev_err(dev,
"can't get irq resource ret=%d\n", bank->irq);
return bank->irq;
}
bank->chip.parent = dev;
bank->chip.owner = THIS_MODULE;
bank->dbck_flag = pdata->dbck_flag;
bank->stride = pdata->bank_stride;
bank->width = pdata->bank_width;
bank->is_mpuio = pdata->is_mpuio;
bank->non_wakeup_gpios = pdata->non_wakeup_gpios;
bank->regs = pdata->regs;
#ifdef CONFIG_OF_GPIO
bank->chip.of_node = of_node_get(node);
#endif
if (node) {
if (!of_property_read_bool(node, "ti,gpio-always-on"))
bank->loses_context = true;
} else {
bank->loses_context = pdata->loses_context;
if (bank->loses_context)
bank->get_context_loss_count =
pdata->get_context_loss_count;
}
if (bank->regs->set_dataout && bank->regs->clr_dataout) {
bank->set_dataout = omap_set_gpio_dataout_reg;
bank->set_dataout_multiple = omap_set_gpio_dataout_reg_multiple;
} else {
bank->set_dataout = omap_set_gpio_dataout_mask;
bank->set_dataout_multiple =
omap_set_gpio_dataout_mask_multiple;
}
raw_spin_lock_init(&bank->lock);
raw_spin_lock_init(&bank->wa_lock);
/* Static mapping, never released */
bank->base = devm_platform_ioremap_resource(pdev, 0);
if (IS_ERR(bank->base)) {
return PTR_ERR(bank->base);
}
if (bank->dbck_flag) {
bank->dbck = devm_clk_get(dev, "dbclk");
if (IS_ERR(bank->dbck)) {
dev_err(dev,
"Could not get gpio dbck. Disable debounce\n");
bank->dbck_flag = false;
} else {
clk_prepare(bank->dbck);
}
}
platform_set_drvdata(pdev, bank);
pm_runtime_enable(dev);
pm_runtime_get_sync(dev);
if (bank->is_mpuio)
omap_mpuio_init(bank);
omap_gpio_mod_init(bank);
ret = omap_gpio_chip_init(bank, irqc);
if (ret) {
pm_runtime_put_sync(dev);
pm_runtime_disable(dev);
if (bank->dbck_flag)
clk_unprepare(bank->dbck);
return ret;
}
omap_gpio_show_rev(bank);
bank->nb.notifier_call = gpio_omap_cpu_notifier;
cpu_pm_register_notifier(&bank->nb);
pm_runtime_put(dev);
return 0;
}
static int omap_gpio_remove(struct platform_device *pdev)
{
struct gpio_bank *bank = platform_get_drvdata(pdev);
cpu_pm_unregister_notifier(&bank->nb);
list_del(&bank->node);
gpiochip_remove(&bank->chip);
pm_runtime_disable(&pdev->dev);
if (bank->dbck_flag)
clk_unprepare(bank->dbck);
return 0;
}
static int __maybe_unused omap_gpio_runtime_suspend(struct device *dev)
{
struct gpio_bank *bank = dev_get_drvdata(dev);
unsigned long flags;
raw_spin_lock_irqsave(&bank->lock, flags);
omap_gpio_idle(bank, true);
bank->is_suspended = true;
raw_spin_unlock_irqrestore(&bank->lock, flags);
return 0;
}
static int __maybe_unused omap_gpio_runtime_resume(struct device *dev)
{
struct gpio_bank *bank = dev_get_drvdata(dev);
unsigned long flags;
raw_spin_lock_irqsave(&bank->lock, flags);
omap_gpio_unidle(bank);
bank->is_suspended = false;
raw_spin_unlock_irqrestore(&bank->lock, flags);
return 0;
}
static const struct dev_pm_ops gpio_pm_ops = {
SET_RUNTIME_PM_OPS(omap_gpio_runtime_suspend, omap_gpio_runtime_resume,
NULL)
};
static struct platform_driver omap_gpio_driver = {
.probe = omap_gpio_probe,
.remove = omap_gpio_remove,
.driver = {
.name = "omap_gpio",
.pm = &gpio_pm_ops,
.of_match_table = of_match_ptr(omap_gpio_match),
.of_match_table = omap_gpio_match,
},
};
......
drivers/gpio/gpio-pca953x.c
View file @ 8148c17b
......@@ -73,6 +73,7 @@
#define PCA_CHIP_TYPE(x) ((x) & PCA_TYPE_MASK)
static const struct i2c_device_id pca953x_id[] = {
{ "pca6416", 16 | PCA953X_TYPE | PCA_INT, },
{ "pca9505", 40 | PCA953X_TYPE | PCA_INT, },
{ "pca9534", 8 | PCA953X_TYPE | PCA_INT, },
{ "pca9535", 16 | PCA953X_TYPE | PCA_INT, },
......@@ -153,6 +154,7 @@ struct pca953x_chip {
u8 irq_trig_fall[MAX_BANK];
struct irq_chip irq_chip;
#endif
atomic_t wakeup_path;
struct i2c_client *client;
struct gpio_chip gpio_chip;
......@@ -581,6 +583,11 @@ static int pca953x_irq_set_wake(struct irq_data *d, unsigned int on)
struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
struct pca953x_chip *chip = gpiochip_get_data(gc);
if (on)
atomic_inc(&chip->wakeup_path);
else
atomic_dec(&chip->wakeup_path);
return irq_set_irq_wake(chip->client->irq, on);
}
......@@ -1100,7 +1107,10 @@ static int pca953x_suspend(struct device *dev)
regcache_cache_only(chip->regmap, true);
regulator_disable(chip->regulator);
if (atomic_read(&chip->wakeup_path))
device_set_wakeup_path(dev);
else
regulator_disable(chip->regulator);
return 0;
}
......@@ -1110,10 +1120,12 @@ static int pca953x_resume(struct device *dev)
struct pca953x_chip *chip = dev_get_drvdata(dev);
int ret;
ret = regulator_enable(chip->regulator);
if (ret != 0) {
dev_err(dev, "Failed to enable regulator: %d\n", ret);
return 0;
if (!atomic_read(&chip->wakeup_path)) {
ret = regulator_enable(chip->regulator);
if (ret != 0) {
dev_err(dev, "Failed to enable regulator: %d\n", ret);
return 0;
}
}
regcache_cache_only(chip->regmap, false);
......@@ -1137,6 +1149,7 @@ static int pca953x_resume(struct device *dev)
#define OF_957X(__nrgpio, __int) (void *)(__nrgpio | PCA957X_TYPE | __int)
static const struct of_device_id pca953x_dt_ids[] = {
{ .compatible = "nxp,pca6416", .data = OF_953X(16, PCA_INT), },
{ .compatible = "nxp,pca9505", .data = OF_953X(40, PCA_INT), },
{ .compatible = "nxp,pca9534", .data = OF_953X( 8, PCA_INT), },
{ .compatible = "nxp,pca9535", .data = OF_953X(16, PCA_INT), },
......@@ -1152,6 +1165,7 @@ static const struct of_device_id pca953x_dt_ids[] = {
{ .compatible = "nxp,pca9575", .data = OF_957X(16, PCA_INT), },
{ .compatible = "nxp,pca9698", .data = OF_953X(40, 0), },
{ .compatible = "nxp,pcal6416", .data = OF_953X(16, PCA_LATCH_INT), },
{ .compatible = "nxp,pcal6524", .data = OF_953X(24, PCA_LATCH_INT), },
{ .compatible = "nxp,pcal9555a", .data = OF_953X(16, PCA_LATCH_INT), },
......@@ -1167,6 +1181,7 @@ static const struct of_device_id pca953x_dt_ids[] = {
{ .compatible = "ti,tca6416", .data = OF_953X(16, PCA_INT), },
{ .compatible = "ti,tca6424", .data = OF_953X(24, PCA_INT), },
{ .compatible = "onnn,cat9554", .data = OF_953X( 8, PCA_INT), },
{ .compatible = "onnn,pca9654", .data = OF_953X( 8, PCA_INT), },
{ .compatible = "exar,xra1202", .data = OF_953X( 8, 0), },
......
drivers/gpio/gpio-pxa.c
View file @ 8148c17b
......@@ -577,7 +577,7 @@ static int pxa_irq_domain_map(struct irq_domain *d, unsigned int irq,
return 0;
}
const struct irq_domain_ops pxa_irq_domain_ops = {
static const struct irq_domain_ops pxa_irq_domain_ops = {
.map = pxa_irq_domain_map,
.xlate = irq_domain_xlate_twocell,
};
......@@ -622,7 +622,6 @@ static int pxa_gpio_probe(struct platform_device *pdev)
{
struct pxa_gpio_chip *pchip;
struct pxa_gpio_bank *c;
struct resource *res;
struct clk *clk;
struct pxa_gpio_platform_data *info;
void __iomem *gpio_reg_base;
......@@ -665,11 +664,8 @@ static int pxa_gpio_probe(struct platform_device *pdev)
pchip->irq0 = irq0;
pchip->irq1 = irq1;
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
if (!res)
return -EINVAL;
gpio_reg_base = devm_ioremap(&pdev->dev, res->start,
resource_size(res));
gpio_reg_base = devm_platform_ioremap_resource(pdev, 0);
if (!gpio_reg_base)
return -EINVAL;
......@@ -816,7 +812,7 @@ static void pxa_gpio_resume(void)
#define pxa_gpio_resume NULL
#endif
struct syscore_ops pxa_gpio_syscore_ops = {
static struct syscore_ops pxa_gpio_syscore_ops = {
.suspend = pxa_gpio_suspend,
.resume = pxa_gpio_resume,
};
......
drivers/gpio/gpio-rcar.c
View file @ 8148c17b
......@@ -430,7 +430,7 @@ static int gpio_rcar_parse_dt(struct gpio_rcar_priv *p, unsigned int *npins)
static int gpio_rcar_probe(struct platform_device *pdev)
{
struct gpio_rcar_priv *p;
struct resource *io, *irq;
struct resource *irq;
struct gpio_chip *gpio_chip;
struct irq_chip *irq_chip;
struct device *dev = &pdev->dev;
......@@ -461,8 +461,7 @@ static int gpio_rcar_probe(struct platform_device *pdev)
goto err0;
}
io = platform_get_resource(pdev, IORESOURCE_MEM, 0);
p->base = devm_ioremap_resource(dev, io);
p->base = devm_platform_ioremap_resource(pdev, 0);
if (IS_ERR(p->base)) {
ret = PTR_ERR(p->base);
goto err0;
......
drivers/gpio/gpio-sch.c
View file @ 8148c17b
......@@ -23,7 +23,6 @@ struct sch_gpio {
struct gpio_chip chip;
spinlock_t lock;
unsigned short iobase;
unsigned short core_base;
unsigned short resume_base;
};
......@@ -166,7 +165,6 @@ static int sch_gpio_probe(struct platform_device *pdev)
switch (pdev->id) {
case PCI_DEVICE_ID_INTEL_SCH_LPC:
sch->core_base = 0;
sch->resume_base = 10;
sch->chip.ngpio = 14;
......@@ -185,19 +183,16 @@ static int sch_gpio_probe(struct platform_device *pdev)
break;
case PCI_DEVICE_ID_INTEL_ITC_LPC:
sch->core_base = 0;
sch->resume_base = 5;
sch->chip.ngpio = 14;
break;
case PCI_DEVICE_ID_INTEL_CENTERTON_ILB:
sch->core_base = 0;
sch->resume_base = 21;
sch->chip.ngpio = 30;
break;
case PCI_DEVICE_ID_INTEL_QUARK_X1000_ILB:
sch->core_base = 0;
sch->resume_base = 2;
sch->chip.ngpio = 8;
break;
......
drivers/gpio/gpio-spear-spics.c
View file @ 8148c17b
......@@ -122,15 +122,13 @@ static int spics_gpio_probe(struct platform_device *pdev)
{
struct device_node *np = pdev->dev.of_node;
struct spear_spics *spics;
struct resource *res;
int ret;
spics = devm_kzalloc(&pdev->dev, sizeof(*spics), GFP_KERNEL);
if (!spics)
return -ENOMEM;
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
spics->base = devm_ioremap_resource(&pdev->dev, res);
spics->base = devm_platform_ioremap_resource(pdev, 0);
if (IS_ERR(spics->base))
return PTR_ERR(spics->base);
......
drivers/gpio/gpio-sprd.c
View file @ 8148c17b
......@@ -219,7 +219,6 @@ static int sprd_gpio_probe(struct platform_device *pdev)
{
struct gpio_irq_chip *irq;
struct sprd_gpio *sprd_gpio;
struct resource *res;
int ret;
sprd_gpio = devm_kzalloc(&pdev->dev, sizeof(*sprd_gpio), GFP_KERNEL);
......@@ -232,8 +231,7 @@ static int sprd_gpio_probe(struct platform_device *pdev)
return sprd_gpio->irq;
}
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
sprd_gpio->base = devm_ioremap_resource(&pdev->dev, res);
sprd_gpio->base = devm_platform_ioremap_resource(pdev, 0);
if (IS_ERR(sprd_gpio->base))
return PTR_ERR(sprd_gpio->base);
......
drivers/gpio/gpio-sta2x11.c
View file @ 8148c17b
......@@ -360,7 +360,6 @@ static int gsta_probe(struct platform_device *dev)
struct pci_dev *pdev;
struct sta2x11_gpio_pdata *gpio_pdata;
struct gsta_gpio *chip;
struct resource *res;
pdev = *(struct pci_dev **)dev_get_platdata(&dev->dev);
gpio_pdata = dev_get_platdata(&pdev->dev);
......@@ -369,13 +368,11 @@ static int gsta_probe(struct platform_device *dev)
dev_err(&dev->dev, "no gpio config\n");
pr_debug("gpio config: %p\n", gpio_pdata);
res = platform_get_resource(dev, IORESOURCE_MEM, 0);
chip = devm_kzalloc(&dev->dev, sizeof(*chip), GFP_KERNEL);
if (!chip)
return -ENOMEM;
chip->dev = &dev->dev;
chip->reg_base = devm_ioremap_resource(&dev->dev, res);
chip->reg_base = devm_platform_ioremap_resource(dev, 0);
if (IS_ERR(chip->reg_base))
return PTR_ERR(chip->reg_base);
......
drivers/gpio/gpio-stp-xway.c
View file @ 8148c17b
......@@ -210,7 +210,6 @@ static int xway_stp_hw_init(struct xway_stp *chip)
static int xway_stp_probe(struct platform_device *pdev)
{
struct resource *res;
u32 shadow, groups, dsl, phy;
struct xway_stp *chip;
struct clk *clk;
......@@ -220,8 +219,7 @@ static int xway_stp_probe(struct platform_device *pdev)
if (!chip)
return -ENOMEM;
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
chip->virt = devm_ioremap_resource(&pdev->dev, res);
chip->virt = devm_platform_ioremap_resource(pdev, 0);
if (IS_ERR(chip->virt))
return PTR_ERR(chip->virt);
......
drivers/gpio/gpio-tb10x.c
View file @ 8148c17b
......@@ -120,7 +120,6 @@ static irqreturn_t tb10x_gpio_irq_cascade(int irq, void *data)
static int tb10x_gpio_probe(struct platform_device *pdev)
{
struct tb10x_gpio *tb10x_gpio;
struct resource *mem;
struct device *dev = &pdev->dev;
struct device_node *np = dev->of_node;
int ret = -EBUSY;
......@@ -136,8 +135,7 @@ static int tb10x_gpio_probe(struct platform_device *pdev)
if (tb10x_gpio == NULL)
return -ENOMEM;
mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
tb10x_gpio->base = devm_ioremap_resource(dev, mem);
tb10x_gpio->base = devm_platform_ioremap_resource(pdev, 0);
if (IS_ERR(tb10x_gpio->base))
return PTR_ERR(tb10x_gpio->base);
......
drivers/gpio/gpio-tegra.c
View file @ 8148c17b
......@@ -569,7 +569,6 @@ static const struct dev_pm_ops tegra_gpio_pm_ops = {
static int tegra_gpio_probe(struct platform_device *pdev)
{
struct tegra_gpio_info *tgi;
struct resource *res;
struct tegra_gpio_bank *bank;
unsigned int gpio, i, j;
int ret;
......@@ -645,8 +644,7 @@ static int tegra_gpio_probe(struct platform_device *pdev)
bank->tgi = tgi;
}
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
tgi->regs = devm_ioremap_resource(&pdev->dev, res);
tgi->regs = devm_platform_ioremap_resource(pdev, 0);
if (IS_ERR(tgi->regs))
return PTR_ERR(tgi->regs);
......
drivers/gpio/gpio-timberdale.c
View file @ 8148c17b
......@@ -229,7 +229,6 @@ static int timbgpio_probe(struct platform_device *pdev)
struct device *dev = &pdev->dev;
struct gpio_chip *gc;
struct timbgpio *tgpio;
struct resource *iomem;
struct timbgpio_platform_data *pdata = dev_get_platdata(&pdev->dev);
int irq = platform_get_irq(pdev, 0);
......@@ -246,8 +245,7 @@ static int timbgpio_probe(struct platform_device *pdev)
spin_lock_init(&tgpio->lock);
iomem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
tgpio->membase = devm_ioremap_resource(dev, iomem);
tgpio->membase = devm_platform_ioremap_resource(pdev, 0);
if (IS_ERR(tgpio->membase))
return PTR_ERR(tgpio->membase);
......
drivers/gpio/gpio-ts4800.c
View file @ 8148c17b
......@@ -23,7 +23,6 @@ static int ts4800_gpio_probe(struct platform_device *pdev)
{
struct device_node *node;
struct gpio_chip *chip;
struct resource *res;
void __iomem *base_addr;
int retval;
u32 ngpios;
......@@ -32,8 +31,7 @@ static int ts4800_gpio_probe(struct platform_device *pdev)
if (!chip)
return -ENOMEM;
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
base_addr = devm_ioremap_resource(&pdev->dev, res);
base_addr = devm_platform_ioremap_resource(pdev, 0);
if (IS_ERR(base_addr))
return PTR_ERR(base_addr);
......
drivers/gpio/gpio-uniphier.c
View file @ 8148c17b
......@@ -346,7 +346,6 @@ static int uniphier_gpio_probe(struct platform_device *pdev)
struct uniphier_gpio_priv *priv;
struct gpio_chip *chip;
struct irq_chip *irq_chip;
struct resource *regs;
unsigned int nregs;
u32 ngpios;
int ret;
......@@ -370,8 +369,7 @@ static int uniphier_gpio_probe(struct platform_device *pdev)
if (!priv)
return -ENOMEM;
regs = platform_get_resource(pdev, IORESOURCE_MEM, 0);
priv->regs = devm_ioremap_resource(dev, regs);
priv->regs = devm_platform_ioremap_resource(pdev, 0);
if (IS_ERR(priv->regs))
return PTR_ERR(priv->regs);
......
drivers/gpio/gpio-vf610.c
View file @ 8148c17b
......@@ -29,6 +29,7 @@ struct fsl_gpio_soc_data {
struct vf610_gpio_port {
struct gpio_chip gc;
struct irq_chip ic;
void __iomem *base;
void __iomem *gpio_base;
const struct fsl_gpio_soc_data *sdata;
......@@ -60,8 +61,6 @@ struct vf610_gpio_port {
#define PORT_INT_EITHER_EDGE 0xb
#define PORT_INT_LOGIC_ONE 0xc
static struct irq_chip vf610_gpio_irq_chip;
static const struct fsl_gpio_soc_data imx_data = {
.have_paddr = true,
};
......@@ -86,28 +85,24 @@ static int vf610_gpio_get(struct gpio_chip *gc, unsigned int gpio)
{
struct vf610_gpio_port *port = gpiochip_get_data(gc);
unsigned long mask = BIT(gpio);
void __iomem *addr;
unsigned long offset = GPIO_PDIR;
if (port->sdata && port->sdata->have_paddr) {
mask &= vf610_gpio_readl(port->gpio_base + GPIO_PDDR);
addr = mask ? port->gpio_base + GPIO_PDOR :
port->gpio_base + GPIO_PDIR;
return !!(vf610_gpio_readl(addr) & BIT(gpio));
} else {
return !!(vf610_gpio_readl(port->gpio_base + GPIO_PDIR)
& BIT(gpio));
if (mask)
offset = GPIO_PDOR;
}
return !!(vf610_gpio_readl(port->gpio_base + offset) & BIT(gpio));
}
static void vf610_gpio_set(struct gpio_chip *gc, unsigned int gpio, int val)
{
struct vf610_gpio_port *port = gpiochip_get_data(gc);
unsigned long mask = BIT(gpio);
unsigned long offset = val ? GPIO_PSOR : GPIO_PCOR;
if (val)
vf610_gpio_writel(mask, port->gpio_base + GPIO_PSOR);
else
vf610_gpio_writel(mask, port->gpio_base + GPIO_PCOR);
vf610_gpio_writel(mask, port->gpio_base + offset);
}
static int vf610_gpio_direction_input(struct gpio_chip *chip, unsigned gpio)
......@@ -237,37 +232,31 @@ static int vf610_gpio_irq_set_wake(struct irq_data *d, u32 enable)
return 0;
}
static struct irq_chip vf610_gpio_irq_chip = {
.name = "gpio-vf610",
.irq_ack = vf610_gpio_irq_ack,
.irq_mask = vf610_gpio_irq_mask,
.irq_unmask = vf610_gpio_irq_unmask,
.irq_set_type = vf610_gpio_irq_set_type,
.irq_set_wake = vf610_gpio_irq_set_wake,
};
static void vf610_gpio_disable_clk(void *data)
{
clk_disable_unprepare(data);
}
static int vf610_gpio_probe(struct platform_device *pdev)
{
struct device *dev = &pdev->dev;
struct device_node *np = dev->of_node;
struct vf610_gpio_port *port;
struct resource *iores;
struct gpio_chip *gc;
struct irq_chip *ic;
int i;
int ret;
port = devm_kzalloc(&pdev->dev, sizeof(*port), GFP_KERNEL);
port = devm_kzalloc(dev, sizeof(*port), GFP_KERNEL);
if (!port)
return -ENOMEM;
port->sdata = of_device_get_match_data(dev);
iores = platform_get_resource(pdev, IORESOURCE_MEM, 0);
port->base = devm_ioremap_resource(dev, iores);
port->base = devm_platform_ioremap_resource(pdev, 0);
if (IS_ERR(port->base))
return PTR_ERR(port->base);
iores = platform_get_resource(pdev, IORESOURCE_MEM, 1);
port->gpio_base = devm_ioremap_resource(dev, iores);
port->gpio_base = devm_platform_ioremap_resource(pdev, 1);
if (IS_ERR(port->gpio_base))
return PTR_ERR(port->gpio_base);
......@@ -275,11 +264,15 @@ static int vf610_gpio_probe(struct platform_device *pdev)
if (port->irq < 0)
return port->irq;
port->clk_port = devm_clk_get(&pdev->dev, "port");
port->clk_port = devm_clk_get(dev, "port");
if (!IS_ERR(port->clk_port)) {
ret = clk_prepare_enable(port->clk_port);
if (ret)
return ret;
ret = devm_add_action_or_reset(dev, vf610_gpio_disable_clk,
port->clk_port);
if (ret)
return ret;
} else if (port->clk_port == ERR_PTR(-EPROBE_DEFER)) {
/*
* Percolate deferrals, for anything else,
......@@ -288,20 +281,19 @@ static int vf610_gpio_probe(struct platform_device *pdev)
return PTR_ERR(port->clk_port);
}
port->clk_gpio = devm_clk_get(&pdev->dev, "gpio");
port->clk_gpio = devm_clk_get(dev, "gpio");
if (!IS_ERR(port->clk_gpio)) {
ret = clk_prepare_enable(port->clk_gpio);
if (ret) {
clk_disable_unprepare(port->clk_port);
if (ret)
return ret;
ret = devm_add_action_or_reset(dev, vf610_gpio_disable_clk,
port->clk_gpio);
if (ret)
return ret;
}
} else if (port->clk_gpio == ERR_PTR(-EPROBE_DEFER)) {
clk_disable_unprepare(port->clk_port);
return PTR_ERR(port->clk_gpio);
}
platform_set_drvdata(pdev, port);
gc = &port->gc;
gc->of_node = np;
gc->parent = dev;
......@@ -316,7 +308,15 @@ static int vf610_gpio_probe(struct platform_device *pdev)
gc->direction_output = vf610_gpio_direction_output;
gc->set = vf610_gpio_set;
ret = gpiochip_add_data(gc, port);
ic = &port->ic;
ic->name = "gpio-vf610";
ic->irq_ack = vf610_gpio_irq_ack;
ic->irq_mask = vf610_gpio_irq_mask;
ic->irq_unmask = vf610_gpio_irq_unmask;
ic->irq_set_type = vf610_gpio_irq_set_type;
ic->irq_set_wake = vf610_gpio_irq_set_wake;
ret = devm_gpiochip_add_data(dev, gc, port);
if (ret < 0)
return ret;
......@@ -327,39 +327,23 @@ static int vf610_gpio_probe(struct platform_device *pdev)
/* Clear the interrupt status register for all GPIO's */
vf610_gpio_writel(~0, port->base + PORT_ISFR);
ret = gpiochip_irqchip_add(gc, &vf610_gpio_irq_chip, 0,
handle_edge_irq, IRQ_TYPE_NONE);
ret = gpiochip_irqchip_add(gc, ic, 0, handle_edge_irq, IRQ_TYPE_NONE);
if (ret) {
dev_err(dev, "failed to add irqchip\n");
gpiochip_remove(gc);
return ret;
}
gpiochip_set_chained_irqchip(gc, &vf610_gpio_irq_chip, port->irq,
gpiochip_set_chained_irqchip(gc, ic, port->irq,
vf610_gpio_irq_handler);
return 0;
}
static int vf610_gpio_remove(struct platform_device *pdev)
{
struct vf610_gpio_port *port = platform_get_drvdata(pdev);
gpiochip_remove(&port->gc);
if (!IS_ERR(port->clk_port))
clk_disable_unprepare(port->clk_port);
if (!IS_ERR(port->clk_gpio))
clk_disable_unprepare(port->clk_gpio);
return 0;
}
static struct platform_driver vf610_gpio_driver = {
.driver = {
.name = "gpio-vf610",
.of_match_table = vf610_gpio_dt_ids,
},
.probe = vf610_gpio_probe,
.remove = vf610_gpio_remove,
};
builtin_platform_driver(vf610_gpio_driver);
drivers/gpio/gpio-xgene-sb.c
View file @ 8148c17b
......@@ -229,7 +229,6 @@ static int xgene_gpio_sb_probe(struct platform_device *pdev)
{
struct xgene_gpio_sb *priv;
int ret;
struct resource *res;
void __iomem *regs;
struct irq_domain *parent_domain = NULL;
u32 val32;
......@@ -238,8 +237,7 @@ static int xgene_gpio_sb_probe(struct platform_device *pdev)
if (!priv)
return -ENOMEM;
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
regs = devm_ioremap_resource(&pdev->dev, res);
regs = devm_platform_ioremap_resource(pdev, 0);
if (IS_ERR(regs))
return PTR_ERR(regs);
......
drivers/gpio/gpio-xlp.c
View file @ 8148c17b
......@@ -290,22 +290,17 @@ MODULE_DEVICE_TABLE(of, xlp_gpio_of_ids);
static int xlp_gpio_probe(struct platform_device *pdev)
{
struct gpio_chip *gc;
struct resource *iores;
struct xlp_gpio_priv *priv;
void __iomem *gpio_base;
int irq_base, irq, err;
int ngpio;
u32 soc_type;
iores = platform_get_resource(pdev, IORESOURCE_MEM, 0);
if (!iores)
return -ENODEV;
priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL);
if (!priv)
return -ENOMEM;
gpio_base = devm_ioremap_resource(&pdev->dev, iores);
gpio_base = devm_platform_ioremap_resource(pdev, 0);
if (IS_ERR(gpio_base))
return PTR_ERR(gpio_base);
......
drivers/gpio/gpio-zx.c
View file @ 8148c17b
......@@ -218,15 +218,13 @@ static int zx_gpio_probe(struct platform_device *pdev)
{
struct device *dev = &pdev->dev;
struct zx_gpio *chip;
struct resource *res;
int irq, id, ret;
chip = devm_kzalloc(dev, sizeof(*chip), GFP_KERNEL);
if (!chip)
return -ENOMEM;
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
chip->base = devm_ioremap_resource(dev, res);
chip->base = devm_platform_ioremap_resource(pdev, 0);
if (IS_ERR(chip->base))
return PTR_ERR(chip->base);
......
drivers/gpio/gpio-zynq.c
View file @ 8148c17b
......@@ -834,7 +834,6 @@ static int zynq_gpio_probe(struct platform_device *pdev)
int ret, bank_num;
struct zynq_gpio *gpio;
struct gpio_chip *chip;
struct resource *res;
const struct of_device_id *match;
gpio = devm_kzalloc(&pdev->dev, sizeof(*gpio), GFP_KERNEL);
......@@ -849,8 +848,7 @@ static int zynq_gpio_probe(struct platform_device *pdev)
gpio->p_data = match->data;
platform_set_drvdata(pdev, gpio);
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
gpio->base_addr = devm_ioremap_resource(&pdev->dev, res);
gpio->base_addr = devm_platform_ioremap_resource(pdev, 0);
if (IS_ERR(gpio->base_addr))
return PTR_ERR(gpio->base_addr);
......
drivers/gpio/gpiolib-acpi.c
View file @ 8148c17b
......@@ -24,13 +24,13 @@
*
* @node: list-entry of the events list of the struct acpi_gpio_chip
* @handle: handle of ACPI method to execute when the IRQ triggers
* @handler: irq_handler to pass to request_irq when requesting the IRQ
* @pin: GPIO pin number on the gpio_chip
* @irq: Linux IRQ number for the event, for request_ / free_irq
* @irqflags: flags to pass to request_irq when requesting the IRQ
* @handler: handler function to pass to request_irq() when requesting the IRQ
* @pin: GPIO pin number on the struct gpio_chip
* @irq: Linux IRQ number for the event, for request_irq() / free_irq()
* @irqflags: flags to pass to request_irq() when requesting the IRQ
* @irq_is_wake: If the ACPI flags indicate the IRQ is a wakeup source
* @irq_requested:True if request_irq has been done
* @desc: gpio_desc for the GPIO pin for this event
* @irq_requested:True if request_irq() has been done
* @desc: struct gpio_desc for the GPIO pin for this event
*/
struct acpi_gpio_event {
struct list_head node;
......@@ -65,10 +65,10 @@ struct acpi_gpio_chip {
};
/*
* For gpiochips which call acpi_gpiochip_request_interrupts() before late_init
* For GPIO chips which call acpi_gpiochip_request_interrupts() before late_init
* (so builtin drivers) we register the ACPI GpioInt IRQ handlers from a
* late_initcall_sync handler, so that other builtin drivers can register their
* OpRegions before the event handlers can run. This list contains gpiochips
* late_initcall_sync() handler, so that other builtin drivers can register their
* OpRegions before the event handlers can run. This list contains GPIO chips
* for which the acpi_gpiochip_request_irqs() call has been deferred.
*/
static DEFINE_MUTEX(acpi_gpio_deferred_req_irqs_lock);
......@@ -90,7 +90,7 @@ static int acpi_gpiochip_find(struct gpio_chip *gc, void *data)
*
* Return: GPIO descriptor to use with Linux generic GPIO API, or ERR_PTR
* error value. Specifically returns %-EPROBE_DEFER if the referenced GPIO
* controller does not have gpiochip registered at the moment. This is to
* controller does not have GPIO chip registered at the moment. This is to
* support probe deferral.
*/
static struct gpio_desc *acpi_get_gpiod(char *path, int pin)
......@@ -287,9 +287,9 @@ static acpi_status acpi_gpiochip_alloc_event(struct acpi_resource *ares,
*
* ACPI5 platforms can use GPIO signaled ACPI events. These GPIO interrupts are
* handled by ACPI event methods which need to be called from the GPIO
* chip's interrupt handler. acpi_gpiochip_request_interrupts finds out which
* gpio pins have acpi event methods and assigns interrupt handlers that calls
* the acpi event methods for those pins.
* chip's interrupt handler. acpi_gpiochip_request_interrupts() finds out which
* GPIO pins have ACPI event methods and assigns interrupt handlers that calls
* the ACPI event methods for those pins.
*/
void acpi_gpiochip_request_interrupts(struct gpio_chip *chip)
{
......@@ -444,8 +444,6 @@ static bool acpi_get_driver_gpio_data(struct acpi_device *adev,
static enum gpiod_flags
acpi_gpio_to_gpiod_flags(const struct acpi_resource_gpio *agpio)
{
bool pull_up = agpio->pin_config == ACPI_PIN_CONFIG_PULLUP;
switch (agpio->io_restriction) {
case ACPI_IO_RESTRICT_INPUT:
return GPIOD_IN;
......@@ -454,16 +452,26 @@ acpi_gpio_to_gpiod_flags(const struct acpi_resource_gpio *agpio)
* ACPI GPIO resources don't contain an initial value for the
* GPIO. Therefore we deduce that value from the pull field
* instead. If the pin is pulled up we assume default to be
* high, otherwise low.
* high, if it is pulled down we assume default to be low,
* otherwise we leave pin untouched.
*/
return pull_up ? GPIOD_OUT_HIGH : GPIOD_OUT_LOW;
switch (agpio->pin_config) {
case ACPI_PIN_CONFIG_PULLUP:
return GPIOD_OUT_HIGH;
case ACPI_PIN_CONFIG_PULLDOWN:
return GPIOD_OUT_LOW;
default:
break;
}
default:
/*
* Assume that the BIOS has configured the direction and pull
* accordingly.
*/
return GPIOD_ASIS;
break;
}
/*
* Assume that the BIOS has configured the direction and pull
* accordingly.
*/
return GPIOD_ASIS;
}
static int
......@@ -517,6 +525,26 @@ acpi_gpio_update_gpiod_flags(enum gpiod_flags *flags, struct acpi_gpio_info *inf
return ret;
}
int acpi_gpio_update_gpiod_lookup_flags(unsigned long *lookupflags,
struct acpi_gpio_info *info)
{
switch (info->pin_config) {
case ACPI_PIN_CONFIG_PULLUP:
*lookupflags |= GPIO_PULL_UP;
break;
case ACPI_PIN_CONFIG_PULLDOWN:
*lookupflags |= GPIO_PULL_DOWN;
break;
default:
break;
}
if (info->polarity == GPIO_ACTIVE_LOW)
*lookupflags |= GPIO_ACTIVE_LOW;
return 0;
}
struct acpi_gpio_lookup {
struct acpi_gpio_info info;
int index;
......@@ -550,6 +578,7 @@ static int acpi_populate_gpio_lookup(struct acpi_resource *ares, void *data)
lookup->desc = acpi_get_gpiod(agpio->resource_source.string_ptr,
agpio->pin_table[pin_index]);
lookup->info.pin_config = agpio->pin_config;
lookup->info.gpioint = gpioint;
/*
......@@ -653,7 +682,7 @@ static int acpi_gpio_property_lookup(struct fwnode_handle *fwnode,
* that case @index is used to select the GPIO entry in the property value
* (in case of multiple).
*
* If the GPIO cannot be translated or there is an error an ERR_PTR is
* If the GPIO cannot be translated or there is an error, an ERR_PTR is
* returned.
*
* Note: if the GPIO resource has multiple entries in the pin list, this
......@@ -696,7 +725,7 @@ struct gpio_desc *acpi_find_gpio(struct device *dev,
const char *con_id,
unsigned int idx,
enum gpiod_flags *dflags,
enum gpio_lookup_flags *lookupflags)
unsigned long *lookupflags)
{
struct acpi_device *adev = ACPI_COMPANION(dev);
struct acpi_gpio_info info;
......@@ -737,10 +766,8 @@ struct gpio_desc *acpi_find_gpio(struct device *dev,
return ERR_PTR(-ENOENT);
}
if (info.polarity == GPIO_ACTIVE_LOW)
*lookupflags |= GPIO_ACTIVE_LOW;
acpi_gpio_update_gpiod_flags(dflags, &info);
acpi_gpio_update_gpiod_lookup_flags(lookupflags, &info);
return desc;
}
......@@ -751,10 +778,13 @@ struct gpio_desc *acpi_find_gpio(struct device *dev,
* @index: index of GpioIo/GpioInt resource (starting from %0)
* @info: info pointer to fill in (optional)
*
* If @fwnode is an ACPI device object, call %acpi_get_gpiod_by_index() for it.
* Otherwise (ie. it is a data-only non-device object), use the property-based
* If @fwnode is an ACPI device object, call acpi_get_gpiod_by_index() for it.
* Otherwise (i.e. it is a data-only non-device object), use the property-based
* GPIO lookup to get to the GPIO resource with the relevant information and use
* that to obtain the GPIO descriptor to return.
*
* If the GPIO cannot be translated or there is an error an ERR_PTR is
* returned.
*/
struct gpio_desc *acpi_node_get_gpiod(struct fwnode_handle *fwnode,
const char *propname, int index,
......@@ -816,6 +846,7 @@ int acpi_dev_gpio_irq_get(struct acpi_device *adev, int index)
return PTR_ERR(desc);
if (info.gpioint && idx++ == index) {
unsigned long lflags = GPIO_LOOKUP_FLAGS_DEFAULT;
char label[32];
int irq;
......@@ -827,7 +858,7 @@ int acpi_dev_gpio_irq_get(struct acpi_device *adev, int index)
return irq;
snprintf(label, sizeof(label), "GpioInt() %d", index);
ret = gpiod_configure_flags(desc, label, 0, info.flags);
ret = gpiod_configure_flags(desc, label, lflags, info.flags);
if (ret < 0)
return ret;
......@@ -992,16 +1023,19 @@ static void acpi_gpiochip_free_regions(struct acpi_gpio_chip *achip)
}
}
static struct gpio_desc *acpi_gpiochip_parse_own_gpio(
struct acpi_gpio_chip *achip, struct fwnode_handle *fwnode,
const char **name, unsigned int *lflags, unsigned int *dflags)
static struct gpio_desc *
acpi_gpiochip_parse_own_gpio(struct acpi_gpio_chip *achip,
struct fwnode_handle *fwnode,
const char **name,
unsigned long *lflags,
enum gpiod_flags *dflags)
{
struct gpio_chip *chip = achip->chip;
struct gpio_desc *desc;
u32 gpios[2];
int ret;
*lflags = 0;
*lflags = GPIO_LOOKUP_FLAGS_DEFAULT;
*dflags = 0;
*name = NULL;
......@@ -1037,7 +1071,8 @@ static void acpi_gpiochip_scan_gpios(struct acpi_gpio_chip *achip)
struct fwnode_handle *fwnode;
device_for_each_child_node(chip->parent, fwnode) {
unsigned int lflags, dflags;
unsigned long lflags;
enum gpiod_flags dflags;
struct gpio_desc *desc;
const char *name;
int ret;
......@@ -1158,11 +1193,13 @@ static int acpi_find_gpio_count(struct acpi_resource *ares, void *data)
}
/**
* acpi_gpio_count - return the number of GPIOs associated with a
* device / function or -ENOENT if no GPIO has been
* assigned to the requested function.
* @dev: GPIO consumer, can be NULL for system-global GPIOs
* acpi_gpio_count - count the GPIOs associated with a device / function
* @dev: GPIO consumer, can be %NULL for system-global GPIOs
* @con_id: function within the GPIO consumer
*
* Return:
* The number of GPIOs associated with a device / function or %-ENOENT,
* if no GPIO has been assigned to the requested function.
*/
int acpi_gpio_count(struct device *dev, const char *con_id)
{
......
drivers/gpio/gpiolib-of.c
View file @ 8148c17b
......@@ -86,9 +86,9 @@ static void of_gpio_flags_quirks(struct device_node *np,
if (IS_ENABLED(CONFIG_REGULATOR) &&
(of_device_is_compatible(np, "regulator-fixed") ||
of_device_is_compatible(np, "reg-fixed-voltage") ||
(of_device_is_compatible(np, "regulator-gpio") &&
!(strcmp(propname, "enable-gpio") &&
strcmp(propname, "enable-gpios"))))) {
(!(strcmp(propname, "enable-gpio") &&
strcmp(propname, "enable-gpios")) &&
of_device_is_compatible(np, "regulator-gpio")))) {
/*
* The regulator GPIO handles are specified such that the
* presence or absence of "enable-active-high" solely controls
......@@ -119,9 +119,8 @@ static void of_gpio_flags_quirks(struct device_node *np,
* property named "cs-gpios" we need to inspect the child node
* to determine if the flags should have inverted semantics.
*/
if (IS_ENABLED(CONFIG_SPI_MASTER) &&
of_property_read_bool(np, "cs-gpios") &&
!strcmp(propname, "cs-gpios")) {
if (IS_ENABLED(CONFIG_SPI_MASTER) && !strcmp(propname, "cs-gpios") &&
of_property_read_bool(np, "cs-gpios")) {
struct device_node *child;
u32 cs;
int ret;
......@@ -288,8 +287,7 @@ static struct gpio_desc *of_find_regulator_gpio(struct device *dev, const char *
}
struct gpio_desc *of_find_gpio(struct device *dev, const char *con_id,
unsigned int idx,
enum gpio_lookup_flags *flags)
unsigned int idx, unsigned long *flags)
{
char prop_name[32]; /* 32 is max size of property name */
enum of_gpio_flags of_flags;
......@@ -362,8 +360,8 @@ struct gpio_desc *of_find_gpio(struct device *dev, const char *con_id,
* @chip: GPIO chip whose hog is parsed
* @idx: Index of the GPIO to parse
* @name: GPIO line name
* @lflags: gpio_lookup_flags - returned from of_find_gpio() or
* of_parse_own_gpio()
* @lflags: bitmask of gpio_lookup_flags GPIO_* values - returned from
* of_find_gpio() or of_parse_own_gpio()
* @dflags: gpiod_flags - optional GPIO initialization flags
*
* Returns GPIO descriptor to use with Linux GPIO API, or one of the errno
......@@ -372,7 +370,7 @@ struct gpio_desc *of_find_gpio(struct device *dev, const char *con_id,
static struct gpio_desc *of_parse_own_gpio(struct device_node *np,
struct gpio_chip *chip,
unsigned int idx, const char **name,
enum gpio_lookup_flags *lflags,
unsigned long *lflags,
enum gpiod_flags *dflags)
{
struct device_node *chip_np;
......@@ -388,7 +386,7 @@ static struct gpio_desc *of_parse_own_gpio(struct device_node *np,
return ERR_PTR(-EINVAL);
xlate_flags = 0;
*lflags = 0;
*lflags = GPIO_LOOKUP_FLAGS_DEFAULT;
*dflags = 0;
ret = of_property_read_u32(chip_np, "#gpio-cells", &tmp);
......@@ -445,7 +443,7 @@ static int of_gpiochip_scan_gpios(struct gpio_chip *chip)
struct gpio_desc *desc = NULL;
struct device_node *np;
const char *name;
enum gpio_lookup_flags lflags;
unsigned long lflags;
enum gpiod_flags dflags;
unsigned int i;
int ret;
......
drivers/gpio/gpiolib.c
View file @ 8148c17b
......@@ -2519,6 +2519,7 @@ struct gpio_desc *gpiochip_request_own_desc(struct gpio_chip *chip, u16 hwnum,
const char *label,
enum gpiod_flags flags)
{
unsigned long lflags = GPIO_LOOKUP_FLAGS_DEFAULT;
struct gpio_desc *desc = gpiochip_get_desc(chip, hwnum);
int err;
......@@ -2531,7 +2532,7 @@ struct gpio_desc *gpiochip_request_own_desc(struct gpio_chip *chip, u16 hwnum,
if (err < 0)
return ERR_PTR(err);
err = gpiod_configure_flags(desc, label, 0, flags);
err = gpiod_configure_flags(desc, label, lflags, flags);
if (err) {
chip_err(chip, "setup of own GPIO %s failed\n", label);
gpiod_free_commit(desc);
......@@ -2569,8 +2570,20 @@ EXPORT_SYMBOL_GPL(gpiochip_free_own_desc);
static int gpio_set_config(struct gpio_chip *gc, unsigned offset,
enum pin_config_param mode)
{
unsigned long config = { PIN_CONF_PACKED(mode, 0) };
unsigned long config;
unsigned arg;
switch (mode) {
case PIN_CONFIG_BIAS_PULL_DOWN:
case PIN_CONFIG_BIAS_PULL_UP:
arg = 1;
break;
default:
arg = 0;
}
config = PIN_CONF_PACKED(mode, arg);
return gc->set_config ? gc->set_config(gc, offset, config) : -ENOTSUPP;
}
......@@ -3915,8 +3928,7 @@ static struct gpiod_lookup_table *gpiod_find_lookup_table(struct device *dev)
}
static struct gpio_desc *gpiod_find(struct device *dev, const char *con_id,
unsigned int idx,
enum gpio_lookup_flags *flags)
unsigned int idx, unsigned long *flags)
{
struct gpio_desc *desc = ERR_PTR(-ENOENT);
struct gpiod_lookup_table *table;
......@@ -4072,8 +4084,8 @@ EXPORT_SYMBOL_GPL(gpiod_get_optional);
* gpiod_configure_flags - helper function to configure a given GPIO
* @desc: gpio whose value will be assigned
* @con_id: function within the GPIO consumer
* @lflags: gpio_lookup_flags - returned from of_find_gpio() or
* of_get_gpio_hog()
* @lflags: bitmask of gpio_lookup_flags GPIO_* values - returned from
* of_find_gpio() or of_get_gpio_hog()
* @dflags: gpiod_flags - optional GPIO initialization flags
*
* Return 0 on success, -ENOENT if no GPIO has been assigned to the
......@@ -4155,9 +4167,9 @@ struct gpio_desc *__must_check gpiod_get_index(struct device *dev,
unsigned int idx,
enum gpiod_flags flags)
{
unsigned long lookupflags = GPIO_LOOKUP_FLAGS_DEFAULT;
struct gpio_desc *desc = NULL;
int status;
enum gpio_lookup_flags lookupflags = 0;
/* Maybe we have a device name, maybe not */
const char *devname = dev ? dev_name(dev) : "?";
......@@ -4242,8 +4254,8 @@ struct gpio_desc *gpiod_get_from_of_node(struct device_node *node,
enum gpiod_flags dflags,
const char *label)
{
unsigned long lflags = GPIO_LOOKUP_FLAGS_DEFAULT;
struct gpio_desc *desc;
unsigned long lflags = 0;
enum of_gpio_flags flags;
bool active_low = false;
bool single_ended = false;
......@@ -4321,8 +4333,8 @@ struct gpio_desc *fwnode_get_named_gpiod(struct fwnode_handle *fwnode,
enum gpiod_flags dflags,
const char *label)
{
unsigned long lflags = GPIO_LOOKUP_FLAGS_DEFAULT;
struct gpio_desc *desc = ERR_PTR(-ENODEV);
unsigned long lflags = 0;
int ret;
if (!fwnode)
......@@ -4342,9 +4354,7 @@ struct gpio_desc *fwnode_get_named_gpiod(struct fwnode_handle *fwnode,
return desc;
acpi_gpio_update_gpiod_flags(&dflags, &info);
if (info.polarity == GPIO_ACTIVE_LOW)
lflags |= GPIO_ACTIVE_LOW;
acpi_gpio_update_gpiod_lookup_flags(&lflags, &info);
}
/* Currently only ACPI takes this path */
......@@ -4395,8 +4405,8 @@ EXPORT_SYMBOL_GPL(gpiod_get_index_optional);
* gpiod_hog - Hog the specified GPIO desc given the provided flags
* @desc: gpio whose value will be assigned
* @name: gpio line name
* @lflags: gpio_lookup_flags - returned from of_find_gpio() or
* of_get_gpio_hog()
* @lflags: bitmask of gpio_lookup_flags GPIO_* values - returned from
* of_find_gpio() or of_get_gpio_hog()
* @dflags: gpiod_flags - optional GPIO initialization flags
*/
int gpiod_hog(struct gpio_desc *desc, const char *name,
......@@ -4449,8 +4459,6 @@ int gpiod_hog(struct gpio_desc *desc, const char *name,
/**
* gpiochip_free_hogs - Scan gpio-controller chip and release GPIO hog
* @chip: gpio chip to act on
*
* This is only used by of_gpiochip_remove to free hogged gpios
*/
static void gpiochip_free_hogs(struct gpio_chip *chip)
{
......@@ -4620,7 +4628,8 @@ EXPORT_SYMBOL_GPL(gpiod_get_array_optional);
*/
void gpiod_put(struct gpio_desc *desc)
{
gpiod_free(desc);
if (desc)
gpiod_free(desc);
}
EXPORT_SYMBOL_GPL(gpiod_put);
......
drivers/gpio/gpiolib.h
View file @ 8148c17b
......@@ -17,7 +17,6 @@
#include <linux/cdev.h>
enum of_gpio_flags;
enum gpio_lookup_flags;
struct acpi_device;
/**
......@@ -75,6 +74,7 @@ struct gpio_device {
* @adev: reference to ACPI device which consumes GPIO resource
* @flags: GPIO initialization flags
* @gpioint: if %true this GPIO is of type GpioInt otherwise type is GpioIo
* @pin_config: pin bias as provided by ACPI
* @polarity: interrupt polarity as provided by ACPI
* @triggering: triggering type as provided by ACPI
* @quirks: Linux specific quirks as provided by struct acpi_gpio_mapping
......@@ -83,6 +83,7 @@ struct acpi_gpio_info {
struct acpi_device *adev;
enum gpiod_flags flags;
bool gpioint;
int pin_config;
int polarity;
int triggering;
unsigned int quirks;
......@@ -95,7 +96,7 @@ static __maybe_unused const char * const gpio_suffixes[] = { "gpios", "gpio" };
struct gpio_desc *of_find_gpio(struct device *dev,
const char *con_id,
unsigned int idx,
enum gpio_lookup_flags *flags);
unsigned long *lookupflags);
struct gpio_desc *of_get_named_gpiod_flags(struct device_node *np,
const char *list_name, int index, enum of_gpio_flags *flags);
int of_gpiochip_add(struct gpio_chip *gc);
......@@ -104,7 +105,7 @@ void of_gpiochip_remove(struct gpio_chip *gc);
static inline struct gpio_desc *of_find_gpio(struct device *dev,
const char *con_id,
unsigned int idx,
enum gpio_lookup_flags *flags)
unsigned long *lookupflags)
{
return ERR_PTR(-ENOENT);
}
......@@ -126,12 +127,14 @@ void acpi_gpiochip_free_interrupts(struct gpio_chip *chip);
int acpi_gpio_update_gpiod_flags(enum gpiod_flags *flags,
struct acpi_gpio_info *info);
int acpi_gpio_update_gpiod_lookup_flags(unsigned long *lookupflags,
struct acpi_gpio_info *info);
struct gpio_desc *acpi_find_gpio(struct device *dev,
const char *con_id,
unsigned int idx,
enum gpiod_flags *dflags,
enum gpio_lookup_flags *lookupflags);
unsigned long *lookupflags);
struct gpio_desc *acpi_node_get_gpiod(struct fwnode_handle *fwnode,
const char *propname, int index,
struct acpi_gpio_info *info);
......@@ -154,11 +157,17 @@ acpi_gpio_update_gpiod_flags(enum gpiod_flags *flags, struct acpi_gpio_info *inf
{
return 0;
}
static inline int
acpi_gpio_update_gpiod_lookup_flags(unsigned long *lookupflags,
struct acpi_gpio_info *info)
{
return 0;
}
static inline struct gpio_desc *
acpi_find_gpio(struct device *dev, const char *con_id,
unsigned int idx, enum gpiod_flags *dflags,
enum gpio_lookup_flags *lookupflags)
unsigned long *lookupflags)
{
return ERR_PTR(-ENOENT);
}
......
drivers/pinctrl/pinctrl-mcp23s08.c
View file @ 8148c17b
......@@ -655,115 +655,6 @@ static int mcp23s08_irqchip_setup(struct mcp23s08 *mcp)
/*----------------------------------------------------------------------*/
#ifdef CONFIG_DEBUG_FS
#include <linux/seq_file.h>
/*
* This compares the chip's registers with the register
* cache and corrects any incorrectly set register. This
* can be used to fix state for MCP23xxx, that temporary
* lost its power supply.
*/
#define MCP23S08_CONFIG_REGS 7
static int __check_mcp23s08_reg_cache(struct mcp23s08 *mcp)
{
int cached[MCP23S08_CONFIG_REGS];
int err = 0, i;
/* read cached config registers */
for (i = 0; i < MCP23S08_CONFIG_REGS; i++) {
err = mcp_read(mcp, i, &cached[i]);
if (err)
goto out;
}
regcache_cache_bypass(mcp->regmap, true);
for (i = 0; i < MCP23S08_CONFIG_REGS; i++) {
int uncached;
err = mcp_read(mcp, i, &uncached);
if (err)
goto out;
if (uncached != cached[i]) {
dev_err(mcp->dev, "restoring reg 0x%02x from 0x%04x to 0x%04x (power-loss?)\n",
i, uncached, cached[i]);
mcp_write(mcp, i, cached[i]);
}
}
out:
if (err)
dev_err(mcp->dev, "read error: reg=%02x, err=%d", i, err);
regcache_cache_bypass(mcp->regmap, false);
return err;
}
/*
* This shows more info than the generic gpio dump code:
* pullups, deglitching, open drain drive.
*/
static void mcp23s08_dbg_show(struct seq_file *s, struct gpio_chip *chip)
{
struct mcp23s08 *mcp;
char bank;
int t;
unsigned mask;
int iodir, gpio, gppu;
mcp = gpiochip_get_data(chip);
/* NOTE: we only handle one bank for now ... */
bank = '0' + ((mcp->addr >> 1) & 0x7);
mutex_lock(&mcp->lock);
t = __check_mcp23s08_reg_cache(mcp);
if (t) {
seq_printf(s, " I/O Error\n");
goto done;
}
t = mcp_read(mcp, MCP_IODIR, &iodir);
if (t) {
seq_printf(s, " I/O Error\n");
goto done;
}
t = mcp_read(mcp, MCP_GPIO, &gpio);
if (t) {
seq_printf(s, " I/O Error\n");
goto done;
}
t = mcp_read(mcp, MCP_GPPU, &gppu);
if (t) {
seq_printf(s, " I/O Error\n");
goto done;
}
for (t = 0, mask = BIT(0); t < chip->ngpio; t++, mask <<= 1) {
const char *label;
label = gpiochip_is_requested(chip, t);
if (!label)
continue;
seq_printf(s, " gpio-%-3d P%c.%d (%-12s) %s %s %s\n",
chip->base + t, bank, t, label,
(iodir & mask) ? "in " : "out",
(gpio & mask) ? "hi" : "lo",
(gppu & mask) ? "up" : " ");
/* NOTE: ignoring the irq-related registers */
}
done:
mutex_unlock(&mcp->lock);
}
#else
#define mcp23s08_dbg_show NULL
#endif
/*----------------------------------------------------------------------*/
static int mcp23s08_probe_one(struct mcp23s08 *mcp, struct device *dev,
void *data, unsigned addr, unsigned type,
unsigned int base, int cs)
......@@ -784,7 +675,6 @@ static int mcp23s08_probe_one(struct mcp23s08 *mcp, struct device *dev,
mcp->chip.get = mcp23s08_get;
mcp->chip.direction_output = mcp23s08_direction_output;
mcp->chip.set = mcp23s08_set;
mcp->chip.dbg_show = mcp23s08_dbg_show;
#ifdef CONFIG_OF_GPIO
mcp->chip.of_gpio_n_cells = 2;
mcp->chip.of_node = dev->of_node;
......
include/linux/gpio/driver.h
View file @ 8148c17b
......@@ -227,9 +227,10 @@ struct gpio_irq_chip {
* @reg_dat: data (in) register for generic GPIO
* @reg_set: output set register (out=high) for generic GPIO
* @reg_clr: output clear register (out=low) for generic GPIO
* @reg_dir: direction setting register for generic GPIO
* @bgpio_dir_inverted: indicates that the direction register is inverted
* (gpiolib private state variable)
* @reg_dir_out: direction out setting register for generic GPIO
* @reg_dir_in: direction in setting register for generic GPIO
* @bgpio_dir_unreadable: indicates that the direction register(s) cannot
* be read and we need to rely on out internal state tracking.
* @bgpio_bits: number of register bits used for a generic GPIO i.e.
* <register width> * 8
* @bgpio_lock: used to lock chip->bgpio_data. Also, this is needed to keep
......@@ -237,7 +238,8 @@ struct gpio_irq_chip {
* @bgpio_data: shadowed data register for generic GPIO to clear/set bits
* safely.
* @bgpio_dir: shadowed direction register for generic GPIO to clear/set
* direction safely.
* direction safely. A "1" in this word means the line is set as
* output.
*
* A gpio_chip can help platforms abstract various sources of GPIOs so
* they can all be accessed through a common programing interface.
......@@ -298,8 +300,9 @@ struct gpio_chip {
void __iomem *reg_dat;
void __iomem *reg_set;
void __iomem *reg_clr;
void __iomem *reg_dir;
bool bgpio_dir_inverted;
void __iomem *reg_dir_out;
void __iomem *reg_dir_in;
bool bgpio_dir_unreadable;
int bgpio_bits;
spinlock_t bgpio_lock;
unsigned long bgpio_data;
......
include/linux/gpio/machine.h
View file @ 8148c17b
......@@ -6,14 +6,16 @@
#include <linux/list.h>
enum gpio_lookup_flags {
GPIO_ACTIVE_HIGH = (0 << 0),
GPIO_ACTIVE_LOW = (1 << 0),
GPIO_OPEN_DRAIN = (1 << 1),
GPIO_OPEN_SOURCE = (1 << 2),
GPIO_PERSISTENT = (0 << 3),
GPIO_TRANSITORY = (1 << 3),
GPIO_PULL_UP = (1 << 4),
GPIO_PULL_DOWN = (1 << 5),
GPIO_ACTIVE_HIGH = (0 << 0),
GPIO_ACTIVE_LOW = (1 << 0),
GPIO_OPEN_DRAIN = (1 << 1),
GPIO_OPEN_SOURCE = (1 << 2),
GPIO_PERSISTENT = (0 << 3),
GPIO_TRANSITORY = (1 << 3),
GPIO_PULL_UP = (1 << 4),
GPIO_PULL_DOWN = (1 << 5),
GPIO_LOOKUP_FLAGS_DEFAULT = GPIO_ACTIVE_HIGH | GPIO_PERSISTENT,
};
/**
......@@ -22,7 +24,7 @@ enum gpio_lookup_flags {
* @chip_hwnum: hardware number (i.e. relative to the chip) of the GPIO
* @con_id: name of the GPIO from the device's point of view
* @idx: index of the GPIO in case several GPIOs share the same name
* @flags: mask of GPIO_* values
* @flags: bitmask of gpio_lookup_flags GPIO_* values
*
* gpiod_lookup is a lookup table for associating GPIOs to specific devices and
* functions using platform data.
......@@ -32,7 +34,7 @@ struct gpiod_lookup {
u16 chip_hwnum;
const char *con_id;
unsigned int idx;
enum gpio_lookup_flags flags;
unsigned long flags;
};
struct gpiod_lookup_table {
......@@ -46,7 +48,7 @@ struct gpiod_lookup_table {
* @chip_label: name of the chip the GPIO belongs to
* @chip_hwnum: hardware number (i.e. relative to the chip) of the GPIO
* @line_name: consumer name for the hogged line
* @lflags: mask of GPIO lookup flags
* @lflags: bitmask of gpio_lookup_flags GPIO_* values
* @dflags: GPIO flags used to specify the direction and value
*/
struct gpiod_hog {
......@@ -54,7 +56,7 @@ struct gpiod_hog {
const char *chip_label;
u16 chip_hwnum;
const char *line_name;
enum gpio_lookup_flags lflags;
unsigned long lflags;
int dflags;
};
......
include/linux/platform_data/gpio-omap.h
View file @ 8148c17b
......@@ -200,8 +200,6 @@ struct omap_gpio_platform_data {
bool is_mpuio; /* whether the bank is of type MPUIO */
u32 non_wakeup_gpios;
u32 quirks; /* Version specific quirks mask */
struct omap_gpio_reg_offs *regs;
/* Return context loss count due to PM states changing */
......
include/trace/events/gpio.h
View file @ 8148c17b
......@@ -2,10 +2,6 @@
#undef TRACE_SYSTEM
#define TRACE_SYSTEM gpio
#ifndef CONFIG_TRACING_EVENTS_GPIO
#define NOTRACE
#endif
#if !defined(_TRACE_GPIO_H) || defined(TRACE_HEADER_MULTI_READ)
#define _TRACE_GPIO_H
......
kernel/trace/Kconfig
View file @ 8148c17b
......@@ -774,13 +774,6 @@ config TRACE_EVAL_MAP_FILE
If unsure, say N
config TRACING_EVENTS_GPIO
bool "Trace gpio events"
depends on GPIOLIB
default y
help
Enable tracing events for gpio subsystem
config GCOV_PROFILE_FTRACE
bool "Enable GCOV profiling on ftrace subsystem"
depends on GCOV_KERNEL
......
Markdown is supported
0% or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment
GitLab Nexedi Edition | About GitLab | About Nexedi | 沪ICP备2021021310号-2 | 沪ICP备2021021310号-7