Commit 88b613e6 authored by Steffen Trumtrar's avatar Steffen Trumtrar Committed by Thierry Reding

pwm: add pca9685 driver

Add pwm driver for the NXP pca9685 16 channel pwm-led controller.

The driver is really barebones at this stage. E.g. the OE' pin and
therefore the corresponding registers are not supported.
The driver was tested on a HW where this pin is tied to GND.
Signed-off-by: default avatarSteffen Trumtrar <s.trumtrar@pengutronix.de>
[thierry.reding@gmail.com: style and whitespace cleanups]
Signed-off-by: default avatarThierry Reding <thierry.reding@gmail.com>
parent 8796f9c5
NXP PCA9685 16-channel 12-bit PWM LED controller
================================================
Required properties:
- compatible: "nxp,pca9685-pwm"
- #pwm-cells: should be 2. The first cell specifies the per-chip index
of the PWM to use and the second cell is the period in nanoseconds.
The index 16 is the ALLCALL channel, that sets all PWM channels at the same
time.
Optional properties:
- invert (bool): boolean to enable inverted logic
- open-drain (bool): boolean to configure outputs with open-drain structure;
if omitted use totem-pole structure
Example:
For LEDs that are directly connected to the PCA, the following setting is
applicable:
pca: pca@41 {
compatible = "nxp,pca9685-pwm";
#pwm-cells = <2>;
reg = <0x41>;
invert;
open-drain;
};
...@@ -97,6 +97,15 @@ config PWM_MXS ...@@ -97,6 +97,15 @@ config PWM_MXS
To compile this driver as a module, choose M here: the module To compile this driver as a module, choose M here: the module
will be called pwm-mxs. will be called pwm-mxs.
config PWM_PCA9685
tristate "NXP PCA9685 PWM driver"
depends on OF && REGMAP_I2C
help
Generic PWM framework driver for NXP PCA9685 LED controller.
To compile this driver as a module, choose M here: the module
will be called pwm-pca9685.
config PWM_PUV3 config PWM_PUV3
tristate "PKUnity NetBook-0916 PWM support" tristate "PKUnity NetBook-0916 PWM support"
depends on ARCH_PUV3 depends on ARCH_PUV3
......
...@@ -6,6 +6,7 @@ obj-$(CONFIG_PWM_IMX) += pwm-imx.o ...@@ -6,6 +6,7 @@ obj-$(CONFIG_PWM_IMX) += pwm-imx.o
obj-$(CONFIG_PWM_JZ4740) += pwm-jz4740.o obj-$(CONFIG_PWM_JZ4740) += pwm-jz4740.o
obj-$(CONFIG_PWM_LPC32XX) += pwm-lpc32xx.o obj-$(CONFIG_PWM_LPC32XX) += pwm-lpc32xx.o
obj-$(CONFIG_PWM_MXS) += pwm-mxs.o obj-$(CONFIG_PWM_MXS) += pwm-mxs.o
obj-$(CONFIG_PWM_PCA9685) += pwm-pca9685.o
obj-$(CONFIG_PWM_PUV3) += pwm-puv3.o obj-$(CONFIG_PWM_PUV3) += pwm-puv3.o
obj-$(CONFIG_PWM_PXA) += pwm-pxa.o obj-$(CONFIG_PWM_PXA) += pwm-pxa.o
obj-$(CONFIG_PWM_SAMSUNG) += pwm-samsung.o obj-$(CONFIG_PWM_SAMSUNG) += pwm-samsung.o
......
/*
* Driver for PCA9685 16-channel 12-bit PWM LED controller
*
* Copyright (C) 2013 Steffen Trumtrar <s.trumtrar@pengutronix.de>
*
* based on the pwm-twl-led.c driver
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License version 2 as published by
* the Free Software Foundation.
*
* This program is distributed in the hope that it will be useful, but WITHOUT
* ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
* FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
* more details.
*
* You should have received a copy of the GNU General Public License along with
* this program. If not, see <http://www.gnu.org/licenses/>.
*/
#include <linux/i2c.h>
#include <linux/module.h>
#include <linux/platform_device.h>
#include <linux/pwm.h>
#include <linux/regmap.h>
#include <linux/slab.h>
#define PCA9685_MODE1 0x00
#define PCA9685_MODE2 0x01
#define PCA9685_SUBADDR1 0x02
#define PCA9685_SUBADDR2 0x03
#define PCA9685_SUBADDR3 0x04
#define PCA9685_ALLCALLADDR 0x05
#define PCA9685_LEDX_ON_L 0x06
#define PCA9685_LEDX_ON_H 0x07
#define PCA9685_LEDX_OFF_L 0x08
#define PCA9685_LEDX_OFF_H 0x09
#define PCA9685_ALL_LED_ON_L 0xFA
#define PCA9685_ALL_LED_ON_H 0xFB
#define PCA9685_ALL_LED_OFF_L 0xFC
#define PCA9685_ALL_LED_OFF_H 0xFD
#define PCA9685_PRESCALE 0xFE
#define PCA9685_NUMREGS 0xFF
#define PCA9685_MAXCHAN 0x10
#define LED_FULL (1 << 4)
#define MODE1_SLEEP (1 << 4)
#define MODE2_INVRT (1 << 4)
#define MODE2_OUTDRV (1 << 2)
#define LED_N_ON_H(N) (PCA9685_LEDX_ON_H + (4 * (N)))
#define LED_N_ON_L(N) (PCA9685_LEDX_ON_L + (4 * (N)))
#define LED_N_OFF_H(N) (PCA9685_LEDX_OFF_H + (4 * (N)))
#define LED_N_OFF_L(N) (PCA9685_LEDX_OFF_L + (4 * (N)))
struct pca9685 {
struct pwm_chip chip;
struct regmap *regmap;
int active_cnt;
};
static inline struct pca9685 *to_pca(struct pwm_chip *chip)
{
return container_of(chip, struct pca9685, chip);
}
static int pca9685_pwm_config(struct pwm_chip *chip, struct pwm_device *pwm,
int duty_ns, int period_ns)
{
struct pca9685 *pca = to_pca(chip);
unsigned long long duty;
unsigned int reg;
if (duty_ns < 1) {
if (pwm->hwpwm >= PCA9685_MAXCHAN)
reg = PCA9685_ALL_LED_OFF_H;
else
reg = LED_N_OFF_H(pwm->hwpwm);
regmap_write(pca->regmap, reg, LED_FULL);
return 0;
}
if (duty_ns == period_ns) {
if (pwm->hwpwm >= PCA9685_MAXCHAN)
reg = PCA9685_ALL_LED_ON_H;
else
reg = LED_N_ON_H(pwm->hwpwm);
regmap_write(pca->regmap, reg, LED_FULL);
return 0;
}
duty = 4096 * (unsigned long long)duty_ns;
duty = DIV_ROUND_UP_ULL(duty, period_ns);
if (pwm->hwpwm >= PCA9685_MAXCHAN)
reg = PCA9685_ALL_LED_OFF_L;
else
reg = LED_N_OFF_L(pwm->hwpwm);
regmap_write(pca->regmap, reg, (int)duty & 0xff);
if (pwm->hwpwm >= PCA9685_MAXCHAN)
reg = PCA9685_ALL_LED_OFF_H;
else
reg = LED_N_OFF_H(pwm->hwpwm);
regmap_write(pca->regmap, reg, ((int)duty >> 8) & 0xf);
return 0;
}
static int pca9685_pwm_enable(struct pwm_chip *chip, struct pwm_device *pwm)
{
struct pca9685 *pca = to_pca(chip);
unsigned int reg;
/*
* The PWM subsystem does not support a pre-delay.
* So, set the ON-timeout to 0
*/
if (pwm->hwpwm >= PCA9685_MAXCHAN)
reg = PCA9685_ALL_LED_ON_L;
else
reg = LED_N_ON_L(pwm->hwpwm);
regmap_write(pca->regmap, reg, 0);
if (pwm->hwpwm >= PCA9685_MAXCHAN)
reg = PCA9685_ALL_LED_ON_H;
else
reg = LED_N_ON_H(pwm->hwpwm);
regmap_write(pca->regmap, reg, 0);
/*
* Clear the full-off bit.
* It has precedence over the others and must be off.
*/
if (pwm->hwpwm >= PCA9685_MAXCHAN)
reg = PCA9685_ALL_LED_OFF_H;
else
reg = LED_N_OFF_H(pwm->hwpwm);
regmap_update_bits(pca->regmap, reg, LED_FULL, 0x0);
return 0;
}
static void pca9685_pwm_disable(struct pwm_chip *chip, struct pwm_device *pwm)
{
struct pca9685 *pca = to_pca(chip);
unsigned int reg;
if (pwm->hwpwm >= PCA9685_MAXCHAN)
reg = PCA9685_ALL_LED_OFF_H;
else
reg = LED_N_OFF_H(pwm->hwpwm);
regmap_write(pca->regmap, reg, LED_FULL);
/* Clear the LED_OFF counter. */
if (pwm->hwpwm >= PCA9685_MAXCHAN)
reg = PCA9685_ALL_LED_OFF_L;
else
reg = LED_N_OFF_L(pwm->hwpwm);
regmap_write(pca->regmap, reg, 0x0);
}
static int pca9685_pwm_request(struct pwm_chip *chip, struct pwm_device *pwm)
{
struct pca9685 *pca = to_pca(chip);
if (pca->active_cnt++ == 0)
return regmap_update_bits(pca->regmap, PCA9685_MODE1,
MODE1_SLEEP, 0x0);
return 0;
}
static void pca9685_pwm_free(struct pwm_chip *chip, struct pwm_device *pwm)
{
struct pca9685 *pca = to_pca(chip);
if (--pca->active_cnt == 0)
regmap_update_bits(pca->regmap, PCA9685_MODE1, MODE1_SLEEP,
0x1);
}
static const struct pwm_ops pca9685_pwm_ops = {
.enable = pca9685_pwm_enable,
.disable = pca9685_pwm_disable,
.config = pca9685_pwm_config,
.request = pca9685_pwm_request,
.free = pca9685_pwm_free,
};
static struct regmap_config pca9685_regmap_i2c_config = {
.reg_bits = 8,
.val_bits = 8,
.max_register = PCA9685_NUMREGS,
.cache_type = REGCACHE_NONE,
};
static int pca9685_pwm_probe(struct i2c_client *client,
const struct i2c_device_id *id)
{
struct device_node *np = client->dev.of_node;
struct pca9685 *pca;
int ret;
int mode2;
pca = devm_kzalloc(&client->dev, sizeof(*pca), GFP_KERNEL);
if (!pca)
return -ENOMEM;
pca->regmap = devm_regmap_init_i2c(client, &pca9685_regmap_i2c_config);
if (IS_ERR(pca->regmap)) {
ret = PTR_ERR(pca->regmap);
dev_err(&client->dev, "Failed to initialize register map: %d\n",
ret);
return ret;
}
i2c_set_clientdata(client, pca);
regmap_read(pca->regmap, PCA9685_MODE2, &mode2);
if (of_property_read_bool(np, "invert"))
mode2 |= MODE2_INVRT;
else
mode2 &= ~MODE2_INVRT;
if (of_property_read_bool(np, "open-drain"))
mode2 &= ~MODE2_OUTDRV;
else
mode2 |= MODE2_OUTDRV;
regmap_write(pca->regmap, PCA9685_MODE2, mode2);
/* clear all "full off" bits */
regmap_write(pca->regmap, PCA9685_ALL_LED_OFF_L, 0);
regmap_write(pca->regmap, PCA9685_ALL_LED_OFF_H, 0);
pca->chip.ops = &pca9685_pwm_ops;
/* add an extra channel for ALL_LED */
pca->chip.npwm = PCA9685_MAXCHAN + 1;
pca->chip.dev = &client->dev;
pca->chip.base = -1;
pca->chip.can_sleep = true;
return pwmchip_add(&pca->chip);
}
static int pca9685_pwm_remove(struct i2c_client *client)
{
struct pca9685 *pca = i2c_get_clientdata(client);
regmap_update_bits(pca->regmap, PCA9685_MODE1, MODE1_SLEEP, 0x1);
return pwmchip_remove(&pca->chip);
}
static const struct i2c_device_id pca9685_id[] = {
{ "pca9685", 0 },
{ /* sentinel */ },
};
MODULE_DEVICE_TABLE(i2c, pca9685_id);
static const struct of_device_id pca9685_dt_ids[] = {
{ .compatible = "nxp,pca9685-pwm", },
{ /* sentinel */ }
};
MODULE_DEVICE_TABLE(of, pca9685_dt_ids);
static struct i2c_driver pca9685_i2c_driver = {
.driver = {
.name = "pca9685-pwm",
.owner = THIS_MODULE,
.of_match_table = pca9685_dt_ids,
},
.probe = pca9685_pwm_probe,
.remove = pca9685_pwm_remove,
.id_table = pca9685_id,
};
module_i2c_driver(pca9685_i2c_driver);
MODULE_AUTHOR("Steffen Trumtrar <s.trumtrar@pengutronix.de>");
MODULE_DESCRIPTION("PWM driver for PCA9685");
MODULE_LICENSE("GPL");
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment