Merge tag 'armsoc-for-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC fixes from Olof Johansson:
 "Another week, another small batch of fixes.

  Most of these make zynq, socfpga and sunxi platforms work a bit
  better:

   - due to new requirements for regulators, DWMMC on socfpga broke past
     v3.17
   - SMP spinup fix for socfpga
   - a few DT fixes for zynq
   - another option (FIXED_REGULATOR) for sunxi is needed that used to
     be selected by other options but no longer is.
   - a couple of small DT fixes for at91
   - ...and a couple for i.MX"

* tag 'armsoc-for-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  ARM: dts: imx28-evk: Let i2c0 run at 100kHz
  ARM: i.MX6: Fix "emi" clock name typo
  ARM: multi_v7_defconfig: enable CONFIG_MMC_DW_ROCKCHIP
  ARM: sunxi_defconfig: enable CONFIG_REGULATOR_FIXED_VOLTAGE
  ARM: dts: socfpga: Add a 3.3V fixed regulator node
  ARM: dts: socfpga: Fix SD card detect
  ARM: dts: socfpga: rename gpio nodes
  ARM: at91/dt: sam9263: fix PLLB frequencies
  power: reset: at91-reset: fix power down register
  MAINTAINERS: add atmel ssc driver maintainer entry
  arm: socfpga: fix fetching cpu1start_addr for SMP
  ARM: zynq: DT: trivial: Fix mc node
  ARM: zynq: DT: Add cadence watchdog node
  ARM: zynq: DT: Add missing reference for memory-controller
  ARM: zynq: DT: Add missing reference for ADC
  ARM: zynq: DT: Add missing address for L2 pl310
  ARM: zynq: DT: Remove 222 MHz OPP
  ARM: zynq: DT: Fix GEM register area size

MAINTAINERS

@@ -1749,6 +1749,13 @@ M:	Nicolas Ferre <nicolas.ferre@atmel.com>
 S:	Supported
 F:	drivers/spi/spi-atmel.*
 
+ATMEL SSC DRIVER
+M:	Bo Shen <voice.shen@atmel.com>
+L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
+S:	Supported
+F:	drivers/misc/atmel-ssc.c
+F:	include/linux/atmel-ssc.h
+
 ATMEL Timer Counter (TC) AND CLOCKSOURCE DRIVERS
 M:	Nicolas Ferre <nicolas.ferre@atmel.com>
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)

arch/arm/boot/dts/at91sam9263.dtsi

@@ -122,9 +122,10 @@ pllb: pllbck {
 					interrupts-extended = <&pmc AT91_PMC_LOCKB>;
 					clocks = <&main>;
 					reg = <1>;
-					atmel,clk-input-range = <1000000 5000000>;
+					atmel,clk-input-range = <1000000 32000000>;
 					#atmel,pll-clk-output-range-cells = <4>;
-					atmel,pll-clk-output-ranges = <70000000 130000000 1 1>;
+					atmel,pll-clk-output-ranges = <80000000 200000000 0 1>,
+								<190000000 240000000 2 1>;
 				};
 
 				mck: masterck {

arch/arm/boot/dts/imx28-evk.dts

@@ -193,7 +193,6 @@ lradc@80050000 {
 			i2c0: i2c@80058000 {
 				pinctrl-names = "default";
 				pinctrl-0 = <&i2c0_pins_a>;
-				clock-frequency = <400000>;
 				status = "okay";
 
 				sgtl5000: codec@0a {

arch/arm/boot/dts/socfpga.dtsi

@@ -547,7 +547,7 @@ i2c3: i2c@ffc07000 {
 			status = "disabled";
 		};
 
-		gpio@ff708000 {
+		gpio0: gpio@ff708000 {
 			#address-cells = <1>;
 			#size-cells = <0>;
 			compatible = "snps,dw-apb-gpio";
@@ -555,7 +555,7 @@ gpio@ff708000 {
 			clocks = <&per_base_clk>;
 			status = "disabled";
 
-			gpio0: gpio-controller@0 {
+			porta: gpio-controller@0 {
 				compatible = "snps,dw-apb-gpio-port";
 				gpio-controller;
 				#gpio-cells = <2>;
@@ -567,7 +567,7 @@ gpio0: gpio-controller@0 {
 			};
 		};
 
-		gpio@ff709000 {
+		gpio1: gpio@ff709000 {
 			#address-cells = <1>;
 			#size-cells = <0>;
 			compatible = "snps,dw-apb-gpio";
@@ -575,7 +575,7 @@ gpio@ff709000 {
 			clocks = <&per_base_clk>;
 			status = "disabled";
 
-			gpio1: gpio-controller@0 {
+			portb: gpio-controller@0 {
 				compatible = "snps,dw-apb-gpio-port";
 				gpio-controller;
 				#gpio-cells = <2>;
@@ -587,7 +587,7 @@ gpio1: gpio-controller@0 {
 			};
 		};
 
-		gpio@ff70a000 {
+		gpio2: gpio@ff70a000 {
 			#address-cells = <1>;
 			#size-cells = <0>;
 			compatible = "snps,dw-apb-gpio";
@@ -595,7 +595,7 @@ gpio@ff70a000 {
 			clocks = <&per_base_clk>;
 			status = "disabled";
 
-			gpio2: gpio-controller@0 {
+			portc: gpio-controller@0 {
 				compatible = "snps,dw-apb-gpio-port";
 				gpio-controller;
 				#gpio-cells = <2>;

arch/arm/boot/dts/socfpga_arria5.dtsi

@@ -29,7 +29,7 @@ osc1 {
 			};
 		};
 
-		dwmmc0@ff704000 {
+		mmc0: dwmmc0@ff704000 {
 			num-slots = <1>;
 			broken-cd;
 			bus-width = <4>;

arch/arm/boot/dts/socfpga_arria5_socdk.dts

@@ -37,6 +37,13 @@ aliases {
 		*/
 		ethernet0 = &gmac1;
 	};
+
+	regulator_3_3v: 3-3-v-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "3.3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
 };
 
 &gmac1 {
@@ -68,6 +75,11 @@ rtc@68 {
 	};
 };
 
+&mmc0 {
+	vmmc-supply = <&regulator_3_3v>;
+	vqmmc-supply = <&regulator_3_3v>;
+};
+
 &usb1 {
 	status = "okay";
 };

arch/arm/boot/dts/socfpga_cyclone5_socdk.dts

@@ -37,6 +37,13 @@ aliases {
 		 */
 		ethernet0 = &gmac1;
 	};
+
+	regulator_3_3v: 3-3-v-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "3.3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
 };
 
 &gmac1 {
@@ -53,6 +60,10 @@ &gmac1 {
 	rxc-skew-ps = <2000>;
 };
 
+&gpio1 {
+	status = "okay";
+};
+
 &i2c0 {
 	status = "okay";
 
@@ -69,7 +80,9 @@ rtc@68 {
 };
 
 &mmc0 {
-	cd-gpios = <&gpio1 18 0>;
+	cd-gpios = <&portb 18 0>;
+	vmmc-supply = <&regulator_3_3v>;
+	vqmmc-supply = <&regulator_3_3v>;
 };
 
 &usb1 {

arch/arm/boot/dts/socfpga_cyclone5_sockit.dts

@@ -37,6 +37,13 @@ aliases {
 		 */
 		ethernet0 = &gmac1;
 	};
+
+	regulator_3_3v: vcc3p3-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC3P3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
 };
 
 &gmac1 {
@@ -53,6 +60,11 @@ &gmac1 {
 	rxc-skew-ps = <2000>;
 };
 
+&mmc0 {
+	vmmc-supply = <&regulator_3_3v>;
+	vqmmc-supply = <&regulator_3_3v>;
+};
+
 &usb1 {
 	status = "okay";
 };

arch/arm/boot/dts/zynq-7000.dtsi

@@ -30,7 +30,6 @@ cpu@0 {
 				/* kHz    uV */
 				666667  1000000
 				333334  1000000
-				222223  1000000
 			>;
 		};
 
@@ -65,7 +64,7 @@ amba {
 		interrupt-parent = <&intc>;
 		ranges;
 
-		adc@f8007100 {
+		adc: adc@f8007100 {
 			compatible = "xlnx,zynq-xadc-1.00.a";
 			reg = <0xf8007100 0x20>;
 			interrupts = <0 7 4>;
@@ -137,7 +136,7 @@ intc: interrupt-controller@f8f01000 {
 			      <0xF8F00100 0x100>;
 		};
 
-		L2: cache-controller {
+		L2: cache-controller@f8f02000 {
 			compatible = "arm,pl310-cache";
 			reg = <0xF8F02000 0x1000>;
 			arm,data-latency = <3 2 2>;
@@ -146,10 +145,10 @@ L2: cache-controller {
 			cache-level = <2>;
 		};
 
-		memory-controller@f8006000 {
+		mc: memory-controller@f8006000 {
 			compatible = "xlnx,zynq-ddrc-a05";
 			reg = <0xf8006000 0x1000>;
-		} ;
+		};
 
 		uart0: serial@e0000000 {
 			compatible = "xlnx,xuartps", "cdns,uart-r1p8";
@@ -195,7 +194,7 @@ spi1: spi@e0007000 {
 
 		gem0: ethernet@e000b000 {
 			compatible = "cdns,gem";
-			reg = <0xe000b000 0x4000>;
+			reg = <0xe000b000 0x1000>;
 			status = "disabled";
 			interrupts = <0 22 4>;
 			clocks = <&clkc 30>, <&clkc 30>, <&clkc 13>;
@@ -206,7 +205,7 @@ gem0: ethernet@e000b000 {
 
 		gem1: ethernet@e000c000 {
 			compatible = "cdns,gem";
-			reg = <0xe000c000 0x4000>;
+			reg = <0xe000c000 0x1000>;
 			status = "disabled";
 			interrupts = <0 45 4>;
 			clocks = <&clkc 31>, <&clkc 31>, <&clkc 14>;
@@ -315,5 +314,16 @@ scutimer: timer@f8f00600 {
 			reg = <0xf8f00600 0x20>;
 			clocks = <&clkc 4>;
 		};
+
+		watchdog0: watchdog@f8005000 {
+			clocks = <&clkc 45>;
+			compatible = "xlnx,zynq-wdt-r1p2";
+			device_type = "watchdog";
+			interrupt-parent = <&intc>;
+			interrupts = <0 9 1>;
+			reg = <0xf8005000 0x1000>;
+			reset = <0>;
+			timeout-sec = <10>;
+		};
 	};
 };

arch/arm/configs/multi_v7_defconfig

@@ -354,6 +354,7 @@ CONFIG_MMC_MVSDIO=y
 CONFIG_MMC_SUNXI=y
 CONFIG_MMC_DW=y
 CONFIG_MMC_DW_EXYNOS=y
+CONFIG_MMC_DW_ROCKCHIP=y
 CONFIG_NEW_LEDS=y
 CONFIG_LEDS_CLASS=y
 CONFIG_LEDS_GPIO=y

arch/arm/configs/sunxi_defconfig

@@ -76,6 +76,7 @@ CONFIG_WATCHDOG=y
 CONFIG_SUNXI_WATCHDOG=y
 CONFIG_MFD_AXP20X=y
 CONFIG_REGULATOR=y
+CONFIG_REGULATOR_FIXED_VOLTAGE=y
 CONFIG_REGULATOR_GPIO=y
 CONFIG_USB=y
 CONFIG_USB_EHCI_HCD=y

arch/arm/mach-imx/clk-imx6q.c

@@ -50,8 +50,8 @@ static const char *pcie_axi_sels[]	= { "axi", "ahb", };
 static const char *ssi_sels[]		= { "pll3_pfd2_508m", "pll3_pfd3_454m", "pll4_audio_div", };
 static const char *usdhc_sels[]	= { "pll2_pfd2_396m", "pll2_pfd0_352m", };
 static const char *enfc_sels[]	= { "pll2_pfd0_352m", "pll2_bus", "pll3_usb_otg", "pll2_pfd2_396m", };
-static const char *emi_sels[]		= { "pll2_pfd2_396m", "pll3_usb_otg", "axi", "pll2_pfd0_352m", };
-static const char *emi_slow_sels[]      = { "axi", "pll3_usb_otg", "pll2_pfd2_396m", "pll2_pfd0_352m", };
+static const char *eim_sels[]		= { "pll2_pfd2_396m", "pll3_usb_otg", "axi", "pll2_pfd0_352m", };
+static const char *eim_slow_sels[]      = { "axi", "pll3_usb_otg", "pll2_pfd2_396m", "pll2_pfd0_352m", };
 static const char *vdo_axi_sels[]	= { "axi", "ahb", };
 static const char *vpu_axi_sels[]	= { "axi", "pll2_pfd2_396m", "pll2_pfd0_352m", };
 static const char *cko1_sels[]	= { "pll3_usb_otg", "pll2_bus", "pll1_sys", "pll5_video_div",
@@ -302,8 +302,8 @@ static void __init imx6q_clocks_init(struct device_node *ccm_node)
 	clk[IMX6QDL_CLK_USDHC3_SEL]       = imx_clk_fixup_mux("usdhc3_sel", base + 0x1c, 18, 1, usdhc_sels,        ARRAY_SIZE(usdhc_sels), imx_cscmr1_fixup);
 	clk[IMX6QDL_CLK_USDHC4_SEL]       = imx_clk_fixup_mux("usdhc4_sel", base + 0x1c, 19, 1, usdhc_sels,        ARRAY_SIZE(usdhc_sels), imx_cscmr1_fixup);
 	clk[IMX6QDL_CLK_ENFC_SEL]         = imx_clk_mux("enfc_sel",         base + 0x2c, 16, 2, enfc_sels,         ARRAY_SIZE(enfc_sels));
-	clk[IMX6QDL_CLK_EMI_SEL]          = imx_clk_fixup_mux("emi_sel",      base + 0x1c, 27, 2, emi_sels,        ARRAY_SIZE(emi_sels), imx_cscmr1_fixup);
-	clk[IMX6QDL_CLK_EMI_SLOW_SEL]     = imx_clk_fixup_mux("emi_slow_sel", base + 0x1c, 29, 2, emi_slow_sels,   ARRAY_SIZE(emi_slow_sels), imx_cscmr1_fixup);
+	clk[IMX6QDL_CLK_EIM_SEL]          = imx_clk_fixup_mux("eim_sel",      base + 0x1c, 27, 2, eim_sels,        ARRAY_SIZE(eim_sels), imx_cscmr1_fixup);
+	clk[IMX6QDL_CLK_EIM_SLOW_SEL]     = imx_clk_fixup_mux("eim_slow_sel", base + 0x1c, 29, 2, eim_slow_sels,   ARRAY_SIZE(eim_slow_sels), imx_cscmr1_fixup);
 	clk[IMX6QDL_CLK_VDO_AXI_SEL]      = imx_clk_mux("vdo_axi_sel",      base + 0x18, 11, 1, vdo_axi_sels,      ARRAY_SIZE(vdo_axi_sels));
 	clk[IMX6QDL_CLK_VPU_AXI_SEL]      = imx_clk_mux("vpu_axi_sel",      base + 0x18, 14, 2, vpu_axi_sels,      ARRAY_SIZE(vpu_axi_sels));
 	clk[IMX6QDL_CLK_CKO1_SEL]         = imx_clk_mux("cko1_sel",         base + 0x60, 0,  4, cko1_sels,         ARRAY_SIZE(cko1_sels));
@@ -354,8 +354,8 @@ static void __init imx6q_clocks_init(struct device_node *ccm_node)
 	clk[IMX6QDL_CLK_USDHC4_PODF]      = imx_clk_divider("usdhc4_podf",      "usdhc4_sel",        base + 0x24, 22, 3);
 	clk[IMX6QDL_CLK_ENFC_PRED]        = imx_clk_divider("enfc_pred",        "enfc_sel",          base + 0x2c, 18, 3);
 	clk[IMX6QDL_CLK_ENFC_PODF]        = imx_clk_divider("enfc_podf",        "enfc_pred",         base + 0x2c, 21, 6);
-	clk[IMX6QDL_CLK_EMI_PODF]         = imx_clk_fixup_divider("emi_podf",   "emi_sel",           base + 0x1c, 20, 3, imx_cscmr1_fixup);
-	clk[IMX6QDL_CLK_EMI_SLOW_PODF]    = imx_clk_fixup_divider("emi_slow_podf", "emi_slow_sel",   base + 0x1c, 23, 3, imx_cscmr1_fixup);
+	clk[IMX6QDL_CLK_EIM_PODF]         = imx_clk_fixup_divider("eim_podf",   "eim_sel",           base + 0x1c, 20, 3, imx_cscmr1_fixup);
+	clk[IMX6QDL_CLK_EIM_SLOW_PODF]    = imx_clk_fixup_divider("eim_slow_podf", "eim_slow_sel",   base + 0x1c, 23, 3, imx_cscmr1_fixup);
 	clk[IMX6QDL_CLK_VPU_AXI_PODF]     = imx_clk_divider("vpu_axi_podf",     "vpu_axi_sel",       base + 0x24, 25, 3);
 	clk[IMX6QDL_CLK_CKO1_PODF]        = imx_clk_divider("cko1_podf",        "cko1_sel",          base + 0x60, 4,  3);
 	clk[IMX6QDL_CLK_CKO2_PODF]        = imx_clk_divider("cko2_podf",        "cko2_sel",          base + 0x60, 21, 3);
@@ -456,7 +456,7 @@ static void __init imx6q_clocks_init(struct device_node *ccm_node)
 	clk[IMX6QDL_CLK_USDHC2]       = imx_clk_gate2("usdhc2",        "usdhc2_podf",       base + 0x80, 4);
 	clk[IMX6QDL_CLK_USDHC3]       = imx_clk_gate2("usdhc3",        "usdhc3_podf",       base + 0x80, 6);
 	clk[IMX6QDL_CLK_USDHC4]       = imx_clk_gate2("usdhc4",        "usdhc4_podf",       base + 0x80, 8);
-	clk[IMX6QDL_CLK_EIM_SLOW]     = imx_clk_gate2("eim_slow",      "emi_slow_podf",     base + 0x80, 10);
+	clk[IMX6QDL_CLK_EIM_SLOW]     = imx_clk_gate2("eim_slow",      "eim_slow_podf",     base + 0x80, 10);
 	clk[IMX6QDL_CLK_VDO_AXI]      = imx_clk_gate2("vdo_axi",       "vdo_axi_sel",       base + 0x80, 12);
 	clk[IMX6QDL_CLK_VPU_AXI]      = imx_clk_gate2("vpu_axi",       "vpu_axi_podf",      base + 0x80, 14);
 	clk[IMX6QDL_CLK_CKO1]         = imx_clk_gate("cko1",           "cko1_podf",         base + 0x60, 7);

arch/arm/mach-socfpga/core.h

@@ -40,7 +40,7 @@ extern void __iomem *rst_manager_base_addr;
 extern struct smp_operations socfpga_smp_ops;
 extern char secondary_trampoline, secondary_trampoline_end;
 
-extern unsigned long cpu1start_addr;
+extern unsigned long socfpga_cpu1start_addr;
 
 #define SOCFPGA_SCU_VIRT_BASE   0xfffec000
 

arch/arm/mach-socfpga/headsmp.S

@@ -9,21 +9,26 @@
  */
 #include <linux/linkage.h>
 #include <linux/init.h>
+#include <asm/memory.h>
 
 	.arch	armv7-a
 
 ENTRY(secondary_trampoline)
-	movw	r2, #:lower16:cpu1start_addr
-	movt  r2, #:upper16:cpu1start_addr
-
-	/* The socfpga VT cannot handle a 0xC0000000 page offset when loading
-		the cpu1start_addr, we bit clear it. Tested on HW and VT. */
-	bic	r2, r2, #0x40000000
-
-	ldr	r0, [r2]
-	ldr	r1, [r0]
-	bx	r1
+	/* CPU1 will always fetch from 0x0 when it is brought out of reset.
+	 * Thus, we can just subtract the PAGE_OFFSET to get the physical
+	 * address of &cpu1start_addr. This would not work for platforms
+	 * where the physical memory does not start at 0x0.
+	 */
+	adr	r0, 1f
+	ldmia	r0, {r1, r2}
+	sub	r2, r2, #PAGE_OFFSET
+	ldr	r3, [r2]
+	ldr	r4, [r3]
+	bx	r4
 
+	.align
+1:	.long	.
+	.long	socfpga_cpu1start_addr
 ENTRY(secondary_trampoline_end)
 
 ENTRY(socfpga_secondary_startup)

arch/arm/mach-socfpga/platsmp.c

@@ -33,11 +33,11 @@ static int socfpga_boot_secondary(unsigned int cpu, struct task_struct *idle)
 {
 	int trampoline_size = &secondary_trampoline_end - &secondary_trampoline;
 
-	if (cpu1start_addr) {
+	if (socfpga_cpu1start_addr) {
 		memcpy(phys_to_virt(0), &secondary_trampoline, trampoline_size);
 
 		__raw_writel(virt_to_phys(socfpga_secondary_startup),
-			(sys_manager_base_addr + (cpu1start_addr & 0x000000ff)));
+			(sys_manager_base_addr + (socfpga_cpu1start_addr & 0x000000ff)));
 
 		flush_cache_all();
 		smp_wmb();

arch/arm/mach-socfpga/socfpga.c

@@ -29,7 +29,7 @@
 void __iomem *socfpga_scu_base_addr = ((void __iomem *)(SOCFPGA_SCU_VIRT_BASE));
 void __iomem *sys_manager_base_addr;
 void __iomem *rst_manager_base_addr;
-unsigned long cpu1start_addr;
+unsigned long socfpga_cpu1start_addr;
 
 static struct map_desc scu_io_desc __initdata = {
 	.virtual	= SOCFPGA_SCU_VIRT_BASE,
@@ -70,7 +70,7 @@ void __init socfpga_sysmgr_init(void)
 	np = of_find_compatible_node(NULL, NULL, "altr,sys-mgr");
 
 	if (of_property_read_u32(np, "cpu1-start-addr",
-			(u32 *) &cpu1start_addr))
+			(u32 *) &socfpga_cpu1start_addr))
 		pr_err("SMP: Need cpu1-start-addr in device tree.\n");
 
 	sys_manager_base_addr = of_iomap(np, 0);

drivers/power/reset/at91-reset.c

@@ -100,11 +100,11 @@ static void at91sam9g45_restart(enum reboot_mode mode, const char *cmd)
 		/* Disable SDRAM0 accesses */
 		"1:	str	%3, [%0, #" __stringify(AT91_DDRSDRC_RTR) "]\n\t"
 		/* Power down SDRAM0 */
-		"	str	%4, [%0, #" __stringify(AT91_DDRSDRC_RTR) "]\n\t"
+		"	str	%4, [%0, #" __stringify(AT91_DDRSDRC_LPR) "]\n\t"
 		/* Disable SDRAM1 accesses */
 		"	strne	%3, [%1, #" __stringify(AT91_DDRSDRC_RTR) "]\n\t"
 		/* Power down SDRAM1 */
-		"	strne	%4, [%1, #" __stringify(AT91_DDRSDRC_RTR) "]\n\t"
+		"	strne	%4, [%1, #" __stringify(AT91_DDRSDRC_LPR) "]\n\t"
 		/* Reset CPU */
 		"	str	%5, [%2, #" __stringify(AT91_RSTC_CR) "]\n\t"
 

include/dt-bindings/clock/imx6qdl-clock.h

@@ -62,8 +62,8 @@
 #define IMX6QDL_CLK_USDHC3_SEL			50
 #define IMX6QDL_CLK_USDHC4_SEL			51
 #define IMX6QDL_CLK_ENFC_SEL			52
-#define IMX6QDL_CLK_EMI_SEL			53
-#define IMX6QDL_CLK_EMI_SLOW_SEL		54
+#define IMX6QDL_CLK_EIM_SEL			53
+#define IMX6QDL_CLK_EIM_SLOW_SEL		54
 #define IMX6QDL_CLK_VDO_AXI_SEL			55
 #define IMX6QDL_CLK_VPU_AXI_SEL			56
 #define IMX6QDL_CLK_CKO1_SEL			57
@@ -106,8 +106,8 @@
 #define IMX6QDL_CLK_USDHC4_PODF			94
 #define IMX6QDL_CLK_ENFC_PRED			95
 #define IMX6QDL_CLK_ENFC_PODF			96
-#define IMX6QDL_CLK_EMI_PODF			97
-#define IMX6QDL_CLK_EMI_SLOW_PODF		98
+#define IMX6QDL_CLK_EIM_PODF			97
+#define IMX6QDL_CLK_EIM_SLOW_PODF		98
 #define IMX6QDL_CLK_VPU_AXI_PODF		99
 #define IMX6QDL_CLK_CKO1_PODF			100
 #define IMX6QDL_CLK_AXI				101