Commit 8a68a509 authored by Hans de Goede's avatar Hans de Goede Committed by Mark Brown

ASoC: rt5651: Add support for active-high jack detect

Some boards use a jack-receptacle with a switch which reports the
jack-inserted status as active-high, rather then the standard active-low
reporting most jacks use.

This commit adds support for it. This is activated by a boolean
"realtek,jack-detect-not-inverted" device-property. The not-inverted
in the device-property name, rather then active-high, was chosen to keep
the device-property naming consistent with the rt5640 codec driver.
Signed-off-by: default avatarHans de Goede <hdegoede@redhat.com>
Signed-off-by: default avatarMark Brown <broonie@kernel.org>
parent f68c2a68
......@@ -22,6 +22,11 @@ Optional properties:
2: Use JD1_2 pin for jack-detect
3: Use JD2 pin for jack-detect
- realtek,jack-detect-not-inverted
bool. Normal jack-detect switches give an inverted (active-low) signal,
set this bool in the rare case you've a jack-detect switch which is not
inverted.
- realtek,over-current-threshold-microamp
u32, micbias over-current detection threshold in µA, valid values are
600, 1500 and 2000µA.
......
......@@ -1645,6 +1645,9 @@ static bool rt5651_jack_inserted(struct snd_soc_component *component)
break;
}
if (rt5651->jd_active_high)
return val != 0;
else
return val == 0;
}
......@@ -1868,20 +1871,47 @@ static void rt5651_enable_jack_detect(struct snd_soc_component *component,
case RT5651_JD1_1:
snd_soc_component_update_bits(component, RT5651_JD_CTRL2,
RT5651_JD_TRG_SEL_MASK, RT5651_JD_TRG_SEL_JD1_1);
snd_soc_component_update_bits(component, RT5651_IRQ_CTRL1,
RT5651_JD1_1_IRQ_EN, RT5651_JD1_1_IRQ_EN);
/* active-low is normal, set inv flag for active-high */
if (rt5651->jd_active_high)
snd_soc_component_update_bits(component,
RT5651_IRQ_CTRL1,
RT5651_JD1_1_IRQ_EN | RT5651_JD1_1_INV,
RT5651_JD1_1_IRQ_EN | RT5651_JD1_1_INV);
else
snd_soc_component_update_bits(component,
RT5651_IRQ_CTRL1,
RT5651_JD1_1_IRQ_EN | RT5651_JD1_1_INV,
RT5651_JD1_1_IRQ_EN);
break;
case RT5651_JD1_2:
snd_soc_component_update_bits(component, RT5651_JD_CTRL2,
RT5651_JD_TRG_SEL_MASK, RT5651_JD_TRG_SEL_JD1_2);
snd_soc_component_update_bits(component, RT5651_IRQ_CTRL1,
RT5651_JD1_2_IRQ_EN, RT5651_JD1_2_IRQ_EN);
/* active-low is normal, set inv flag for active-high */
if (rt5651->jd_active_high)
snd_soc_component_update_bits(component,
RT5651_IRQ_CTRL1,
RT5651_JD1_2_IRQ_EN | RT5651_JD1_2_INV,
RT5651_JD1_2_IRQ_EN | RT5651_JD1_2_INV);
else
snd_soc_component_update_bits(component,
RT5651_IRQ_CTRL1,
RT5651_JD1_2_IRQ_EN | RT5651_JD1_2_INV,
RT5651_JD1_2_IRQ_EN);
break;
case RT5651_JD2:
snd_soc_component_update_bits(component, RT5651_JD_CTRL2,
RT5651_JD_TRG_SEL_MASK, RT5651_JD_TRG_SEL_JD2);
snd_soc_component_update_bits(component, RT5651_IRQ_CTRL1,
RT5651_JD2_IRQ_EN, RT5651_JD2_IRQ_EN);
/* active-low is normal, set inv flag for active-high */
if (rt5651->jd_active_high)
snd_soc_component_update_bits(component,
RT5651_IRQ_CTRL1,
RT5651_JD2_IRQ_EN | RT5651_JD2_INV,
RT5651_JD2_IRQ_EN | RT5651_JD2_INV);
else
snd_soc_component_update_bits(component,
RT5651_IRQ_CTRL1,
RT5651_JD2_IRQ_EN | RT5651_JD2_INV,
RT5651_JD2_IRQ_EN);
break;
default:
dev_err(component->dev, "Currently only JD1_1 / JD1_2 / JD2 are supported\n");
......@@ -1986,6 +2016,9 @@ static void rt5651_apply_properties(struct snd_soc_component *component)
"realtek,jack-detect-source", &val) == 0)
rt5651->jd_src = val;
if (device_property_read_bool(component->dev, "realtek,jack-detect-not-inverted"))
rt5651->jd_active_high = true;
/*
* Testing on various boards has shown that good defaults for the OVCD
* threshold and scale-factor are 2000µA and 0.75. For an effective
......
......@@ -2083,6 +2083,7 @@ struct rt5651_priv {
int release_count;
int poll_count;
unsigned int jd_src;
bool jd_active_high;
unsigned int ovcd_th;
unsigned int ovcd_sf;
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment