Merge branch 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus

* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
  [MIPS] Cobalt: update defconfig
  [MIPS] kgdb: add arch support for the kernel's kgdb core
  [MIPS] kgdb: Remove existing implementation
  [MIPS] TXx9: Kconfig cleanup
  [MIPS] TXx9: Kill unused txx927.h
  [MIPS] TXx9: Support early_printk
  [MIPS] TXx9: Unify serial_txx9 setup
  [MIPS] TXx9: Random cleanup
  [MIPS] TXx9: Make tx4938-specific code more independent
  [MIPS] TXx9: Make tx3927-specific code more independent
  [MIPS] TXx9: Cleanup watchdog
  [MIPS] TXx9: Cleanup restart/halt/power_off
  [MIPS] TXx9: PCI error handling
  [MIPS] TXx9: Add some pci options
  [MIPS] Introduce pcibios_plat_setup
  [MIPS] TXx9: PCI fixes for tx3927/tx4927
  [MIPS] TXx9: Fix JMR3927 irq numbers
  [MIPS] RB532: Flags are unsigned long
  [MIPS] Initialization of Alchemy boards
  [MIPS] tlb-r4k: Nuke broken paranoia error test.

arch/mips/Kconfig

@@ -3,6 +3,7 @@ config MIPS
 	default y
 	select HAVE_IDE
 	select HAVE_OPROFILE
+	select HAVE_ARCH_KGDB
 	# Horrible source of confusion.  Die, die, die ...
 	select EMBEDDED
 	select RTC_LIB
@@ -34,7 +35,6 @@ config BASLER_EXCITE
 	select SYS_HAS_CPU_RM9000
 	select SYS_SUPPORTS_32BIT_KERNEL
 	select SYS_SUPPORTS_BIG_ENDIAN
-	select SYS_SUPPORTS_KGDB
 	help
 	  The eXcite is a smart camera platform manufactured by
 	  Basler Vision Technologies AG.
@@ -280,7 +280,6 @@ config PMC_MSP
 	select SYS_HAS_CPU_MIPS32_R2
 	select SYS_SUPPORTS_32BIT_KERNEL
 	select SYS_SUPPORTS_BIG_ENDIAN
-	select SYS_SUPPORTS_KGDB
 	select IRQ_CPU
 	select SERIAL_8250
 	select SERIAL_8250_CONSOLE
@@ -306,7 +305,6 @@ config PMC_YOSEMITE
 	select SYS_SUPPORTS_64BIT_KERNEL
 	select SYS_SUPPORTS_BIG_ENDIAN
 	select SYS_SUPPORTS_HIGHMEM
-	select SYS_SUPPORTS_KGDB
 	select SYS_SUPPORTS_SMP
 	help
 	  Yosemite is an evaluation board for the RM9000x2 processor
@@ -359,7 +357,6 @@ config SGI_IP27
 	select SYS_HAS_CPU_R10000
 	select SYS_SUPPORTS_64BIT_KERNEL
 	select SYS_SUPPORTS_BIG_ENDIAN
-	select SYS_SUPPORTS_KGDB
 	select SYS_SUPPORTS_NUMA
 	select SYS_SUPPORTS_SMP
 	select GENERIC_HARDIRQS_NO__DO_IRQ
@@ -475,7 +472,6 @@ config SIBYTE_SWARM
 	select SYS_HAS_CPU_SB1
 	select SYS_SUPPORTS_BIG_ENDIAN
 	select SYS_SUPPORTS_HIGHMEM
-	select SYS_SUPPORTS_KGDB
 	select SYS_SUPPORTS_LITTLE_ENDIAN
 	select ZONE_DMA32 if 64BIT
 
@@ -868,7 +864,6 @@ config SOC_PNX8550
 	select SYS_HAS_EARLY_PRINTK
 	select SYS_SUPPORTS_32BIT_KERNEL
 	select GENERIC_HARDIRQS_NO__DO_IRQ
-	select SYS_SUPPORTS_KGDB
 	select GENERIC_GPIO
 
 config SWAP_IO_SPACE

arch/mips/Kconfig.debug

@@ -34,28 +34,6 @@ config SMTC_IDLE_HOOK_DEBUG
 	  arch/mips/kernel/smtc.c.  This debugging option result in significant
 	  overhead so should be disabled in production kernels.
 
-config KGDB
-	bool "Remote GDB kernel debugging"
-	depends on DEBUG_KERNEL && SYS_SUPPORTS_KGDB
-	select DEBUG_INFO
-	help
-	  If you say Y here, it will be possible to remotely debug the MIPS
-	  kernel using gdb. This enlarges your kernel image disk size by
-	  several megabytes and requires a machine with more than 16 MB,
-	  better 32 MB RAM to avoid excessive linking time. This is only
-	  useful for kernel hackers. If unsure, say N.
-
-config SYS_SUPPORTS_KGDB
-	bool
-
-config GDB_CONSOLE
-	bool "Console output to GDB"
-	depends on KGDB
-	help
-	  If you are using GDB for remote debugging over a serial port and
-	  would like kernel messages to be formatted into GDB $O packets so
-	  that GDB prints them as program output, say 'Y'.
-
 config SB1XXX_CORELIS
 	bool "Corelis Debugger"
 	depends on SIBYTE_SB1xxx_SOC

arch/mips/au1000/Kconfig

@@ -134,4 +134,3 @@ config SOC_AU1X00
 	select SYS_HAS_CPU_MIPS32_R1
 	select SYS_SUPPORTS_32BIT_KERNEL
 	select SYS_SUPPORTS_APM_EMULATION
-	select SYS_SUPPORTS_KGDB

arch/mips/au1000/common/Makefile

@@ -9,7 +9,6 @@ obj-y += prom.o irq.o puts.o time.o reset.o \
 	au1xxx_irqmap.o clocks.o platform.o power.o setup.o \
 	sleeper.o cputable.o dma.o dbdma.o gpio.o
 
-obj-$(CONFIG_KGDB)		+= dbg_io.o
 obj-$(CONFIG_PCI)		+= pci.o
 
 EXTRA_CFLAGS += -Werror

arch/mips/au1000/common/dbg_io.c

-#include <linux/types.h>
-
-#include <asm/mach-au1x00/au1000.h>
-
-#ifdef CONFIG_KGDB
-
-/*
- * FIXME the user should be able to select the
- * uart to be used for debugging.
- */
-#define DEBUG_BASE  UART_DEBUG_BASE
-
-#define         UART16550_BAUD_2400             2400
-#define         UART16550_BAUD_4800             4800
-#define         UART16550_BAUD_9600             9600
-#define         UART16550_BAUD_19200            19200
-#define         UART16550_BAUD_38400            38400
-#define         UART16550_BAUD_57600            57600
-#define         UART16550_BAUD_115200           115200
-
-#define         UART16550_PARITY_NONE           0
-#define         UART16550_PARITY_ODD            0x08
-#define         UART16550_PARITY_EVEN           0x18
-#define         UART16550_PARITY_MARK           0x28
-#define         UART16550_PARITY_SPACE          0x38
-
-#define         UART16550_DATA_5BIT             0x0
-#define         UART16550_DATA_6BIT             0x1
-#define         UART16550_DATA_7BIT             0x2
-#define         UART16550_DATA_8BIT             0x3
-
-#define         UART16550_STOP_1BIT             0x0
-#define         UART16550_STOP_2BIT             0x4
-
-
-#define UART_RX		0	/* Receive buffer */
-#define UART_TX		4	/* Transmit buffer */
-#define UART_IER	8	/* Interrupt Enable Register */
-#define UART_IIR	0xC	/* Interrupt ID Register */
-#define UART_FCR	0x10	/* FIFO Control Register */
-#define UART_LCR	0x14	/* Line Control Register */
-#define UART_MCR	0x18	/* Modem Control Register */
-#define UART_LSR	0x1C	/* Line Status Register */
-#define UART_MSR	0x20	/* Modem Status Register */
-#define UART_CLK	0x28	/* Baud Rat4e Clock Divider */
-#define UART_MOD_CNTRL	0x100	/* Module Control */
-
-/* memory-mapped read/write of the port */
-#define UART16550_READ(y)     (au_readl(DEBUG_BASE + y) & 0xff)
-#define UART16550_WRITE(y, z) (au_writel(z & 0xff, DEBUG_BASE + y))
-
-extern unsigned long calc_clock(void);
-
-void debugInit(u32 baud, u8 data, u8 parity, u8 stop)
-{
-	if (UART16550_READ(UART_MOD_CNTRL) != 0x3)
-		UART16550_WRITE(UART_MOD_CNTRL, 3);
-	calc_clock();
-
-	/* disable interrupts */
-	UART16550_WRITE(UART_IER, 0);
-
-	/* set up baud rate */
-	{
-		u32 divisor;
-
-		/* set divisor */
-		divisor = get_au1x00_uart_baud_base() / baud;
-		UART16550_WRITE(UART_CLK, divisor & 0xffff);
-	}
-
-	/* set data format */
-	UART16550_WRITE(UART_LCR, (data | parity | stop));
-}
-
-static int remoteDebugInitialized;
-
-u8 getDebugChar(void)
-{
-	if (!remoteDebugInitialized) {
-		remoteDebugInitialized = 1;
-		debugInit(UART16550_BAUD_115200,
-			  UART16550_DATA_8BIT,
-			  UART16550_PARITY_NONE,
-			  UART16550_STOP_1BIT);
-	}
-
-	while ((UART16550_READ(UART_LSR) & 0x1) == 0);
-	return UART16550_READ(UART_RX);
-}
-
-
-int putDebugChar(u8 byte)
-{
-	if (!remoteDebugInitialized) {
-		remoteDebugInitialized = 1;
-		debugInit(UART16550_BAUD_115200,
-			  UART16550_DATA_8BIT,
-			  UART16550_PARITY_NONE,
-			  UART16550_STOP_1BIT);
-	}
-
-	while ((UART16550_READ(UART_LSR) & 0x40) == 0);
-	UART16550_WRITE(UART_TX, byte);
-
-	return 1;
-}
-
-#endif

arch/mips/au1000/db1x00/init.c

@@ -57,6 +57,6 @@ void __init prom_init(void)
 	if (!memsize_str)
 		memsize = 0x04000000;
 	else
-		memsize = strict_strtol(memsize_str, 0, NULL);
+		strict_strtol(memsize_str, 0, &memsize);
 	add_memory_region(0, memsize, BOOT_MEM_RAM);
 }

arch/mips/au1000/mtx-1/init.c

@@ -55,6 +55,6 @@ void __init prom_init(void)
 	if (!memsize_str)
 		memsize = 0x04000000;
 	else
-		memsize = strict_strtol(memsize_str, 0, NULL);
+		strict_strtol(memsize_str, 0, &memsize);
 	add_memory_region(0, memsize, BOOT_MEM_RAM);
 }

arch/mips/au1000/pb1000/init.c

@@ -52,6 +52,6 @@ void __init prom_init(void)
 	if (!memsize_str)
 		memsize = 0x04000000;
 	else
-		memsize = strict_strtol(memsize_str, 0, NULL);
+		strict_strtol(memsize_str, 0, &memsize);
 	add_memory_region(0, memsize, BOOT_MEM_RAM);
 }

arch/mips/au1000/pb1100/init.c

@@ -54,7 +54,7 @@ void __init prom_init(void)
 	if (!memsize_str)
 		memsize = 0x04000000;
 	else
-		memsize = strict_strtol(memsize_str, 0, NULL);
+		strict_strtol(memsize_str, 0, &memsize);
 
 	add_memory_region(0, memsize, BOOT_MEM_RAM);
 }

arch/mips/au1000/pb1200/init.c

@@ -53,6 +53,6 @@ void __init prom_init(void)
 	if (!memsize_str)
 		memsize = 0x08000000;
 	else
-		memsize = strict_strtol(memsize_str, 0, NULL);
+		strict_strtol(memsize_str, 0, &memsize);
 	add_memory_region(0, memsize, BOOT_MEM_RAM);
 }

arch/mips/au1000/pb1500/init.c

@@ -53,6 +53,6 @@ void __init prom_init(void)
 	if (!memsize_str)
 		memsize = 0x04000000;
 	else
-		memsize = strict_strtol(memsize_str, 0, NULL);
+		strict_strtol(memsize_str, 0, &memsize);
 	add_memory_region(0, memsize, BOOT_MEM_RAM);
 }

arch/mips/au1000/pb1550/init.c

@@ -53,6 +53,6 @@ void __init prom_init(void)
 	if (!memsize_str)
 		memsize = 0x08000000;
 	else
-		memsize = strict_strtol(memsize_str, 0, NULL);
+		strict_strtol(memsize_str, 0, &memsize);
 	add_memory_region(0, memsize, BOOT_MEM_RAM);
 }

arch/mips/au1000/xxs1500/init.c

@@ -53,6 +53,6 @@ void __init prom_init(void)
 	if (!memsize_str)
 		memsize = 0x04000000;
 	else
-		memsize = strict_strtol(memsize_str, 0, NULL);
+		strict_strtol(memsize_str, 0, &memsize);
 	add_memory_region(0, memsize, BOOT_MEM_RAM);
 }

arch/mips/basler/excite/Makefile

@@ -5,5 +5,4 @@
 obj-$(CONFIG_BASLER_EXCITE)	+= excite_irq.o excite_prom.o excite_setup.o \
 				   excite_device.o excite_procfs.o
 
-obj-$(CONFIG_KGDB)		+= excite_dbg_io.o
 obj-m				+= excite_iodev.o

arch/mips/basler/excite/excite_dbg_io.c

-/*
- *  Copyright (C) 2004 by Basler Vision Technologies AG
- *  Author: Thomas Koeller <thomas.koeller@baslerweb.com>
- *
- *  This program is free software; you can redistribute it and/or modify
- *  it under the terms of the GNU General Public License as published by
- *  the Free Software Foundation; either version 2 of the License, or
- *  (at your option) any later version.
- *
- *  This program is distributed in the hope that it will be useful,
- *  but WITHOUT ANY WARRANTY; without even the implied warranty of
- *  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *  GNU General Public License for more details.
- *
- *  You should have received a copy of the GNU General Public License
- *  along with this program; if not, write to the Free Software
- *  Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
- */
-
-#include <linux/linkage.h>
-#include <linux/init.h>
-#include <linux/kernel.h>
-#include <asm/gdb-stub.h>
-#include <asm/rm9k-ocd.h>
-#include <excite.h>
-
-#if defined(CONFIG_SERIAL_8250) && CONFIG_SERIAL_8250_NR_UARTS > 1
-#error Debug port used by serial driver
-#endif
-
-#define UART_CLK		25000000
-#define BASE_BAUD		(UART_CLK / 16)
-#define REGISTER_BASE_0		0x0208UL
-#define REGISTER_BASE_1		0x0238UL
-
-#define REGISTER_BASE_DBG	REGISTER_BASE_1
-
-#define CPRR	0x0004
-#define UACFG	0x0200
-#define UAINTS	0x0204
-#define UARBR	(REGISTER_BASE_DBG + 0x0000)
-#define UATHR	(REGISTER_BASE_DBG + 0x0004)
-#define UADLL	(REGISTER_BASE_DBG + 0x0008)
-#define UAIER	(REGISTER_BASE_DBG + 0x000c)
-#define UADLH	(REGISTER_BASE_DBG + 0x0010)
-#define UAIIR	(REGISTER_BASE_DBG + 0x0014)
-#define UAFCR	(REGISTER_BASE_DBG + 0x0018)
-#define UALCR	(REGISTER_BASE_DBG + 0x001c)
-#define UAMCR	(REGISTER_BASE_DBG + 0x0020)
-#define UALSR	(REGISTER_BASE_DBG + 0x0024)
-#define UAMSR	(REGISTER_BASE_DBG + 0x0028)
-#define UASCR	(REGISTER_BASE_DBG + 0x002c)
-
-#define	PARITY_NONE	0
-#define	PARITY_ODD	0x08
-#define	PARITY_EVEN	0x18
-#define	PARITY_MARK	0x28
-#define	PARITY_SPACE	0x38
-
-#define	DATA_5BIT	0x0
-#define	DATA_6BIT	0x1
-#define	DATA_7BIT	0x2
-#define	DATA_8BIT	0x3
-
-#define	STOP_1BIT	0x0
-#define	STOP_2BIT	0x4
-
-#define BAUD_DBG	57600
-#define	PARITY_DBG	PARITY_NONE
-#define	DATA_DBG	DATA_8BIT
-#define	STOP_DBG	STOP_1BIT
-
-/* Initialize the serial port for KGDB debugging */
-void __init excite_kgdb_init(void)
-{
-	const u32 divisor = BASE_BAUD / BAUD_DBG;
-
-	/* Take the UART out of reset */
-	titan_writel(0x00ff1cff, CPRR);
-	titan_writel(0x00000000, UACFG);
-	titan_writel(0x00000002, UACFG);
-
-	titan_writel(0x0, UALCR);
-	titan_writel(0x0, UAIER);
-
-	/* Disable FIFOs */
-	titan_writel(0x00, UAFCR);
-
-	titan_writel(0x80, UALCR);
-	titan_writel(divisor & 0xff, UADLL);
-	titan_writel((divisor & 0xff00) >> 8, UADLH);
-	titan_writel(0x0, UALCR);
-
-	titan_writel(DATA_DBG | PARITY_DBG | STOP_DBG, UALCR);
-
-	/* Enable receiver interrupt */
-	titan_readl(UARBR);
-	titan_writel(0x1, UAIER);
-}
-
-int getDebugChar(void)
-{
-	while (!(titan_readl(UALSR) & 0x1));
-	return titan_readl(UARBR);
-}
-
-int putDebugChar(int data)
-{
-	while (!(titan_readl(UALSR) & 0x20));
-	titan_writel(data, UATHR);
-	return 1;
-}
-
-/* KGDB interrupt handler */
-asmlinkage void excite_kgdb_inthdl(void)
-{
-	if (unlikely(
-		((titan_readl(UAIIR) & 0x7) == 4)
-		&& ((titan_readl(UARBR) & 0xff) == 0x3)))
-			set_async_breakpoint(&regs->cp0_epc);
-}

arch/mips/basler/excite/excite_irq.c

@@ -50,10 +50,6 @@ void __init arch_init_irq(void)
 	mips_cpu_irq_init();
 	rm7k_cpu_irq_init();
 	rm9k_cpu_irq_init();
-
-#ifdef CONFIG_KGDB
-	excite_kgdb_init();
-#endif
 }
 
 asmlinkage void plat_irq_dispatch(void)
@@ -90,9 +86,6 @@ asmlinkage void plat_irq_dispatch(void)
 	msgint	    = msgintflags & msgintmask & (0x1 << (TITAN_MSGINT % 0x20));
 	if ((pending & (1 << TITAN_IRQ)) && msgint) {
 		ocd_writel(msgint, INTP0Clear0 + (TITAN_MSGINT / 0x20 * 0x10));
-#if defined(CONFIG_KGDB)
-		excite_kgdb_inthdl();
-#endif
 		do_IRQ(TITAN_IRQ);
 		return;
 	}

arch/mips/basler/excite/excite_setup.c

@@ -95,13 +95,13 @@ static int __init excite_init_console(void)
 	/* Take the DUART out of reset */
 	titan_writel(0x00ff1cff, CPRR);
 
-#if defined(CONFIG_KGDB) || (CONFIG_SERIAL_8250_NR_UARTS > 1)
+#if (CONFIG_SERIAL_8250_NR_UARTS > 1)
 	/* Enable both ports */
 	titan_writel(MASK_SER0 | MASK_SER1, UACFG);
 #else
 	/* Enable port #0 only */
 	titan_writel(MASK_SER0, UACFG);
-#endif	/* defined(CONFIG_KGDB) */
+#endif
 
  	/*
 	 * Set up serial port #0. Do not use autodetection; the result is

arch/mips/configs/db1000_defconfig

@@ -1092,7 +1092,6 @@ CONFIG_ENABLE_MUST_CHECK=y
 CONFIG_LOG_BUF_SHIFT=14
 CONFIG_CROSSCOMPILE=y
 CONFIG_CMDLINE=""
-CONFIG_SYS_SUPPORTS_KGDB=y
 
 #
 # Security options

arch/mips/configs/db1100_defconfig

@@ -1092,7 +1092,6 @@ CONFIG_ENABLE_MUST_CHECK=y
 CONFIG_LOG_BUF_SHIFT=14
 CONFIG_CROSSCOMPILE=y
 CONFIG_CMDLINE=""
-CONFIG_SYS_SUPPORTS_KGDB=y
 
 #
 # Security options

arch/mips/configs/db1200_defconfig

@@ -1174,7 +1174,6 @@ CONFIG_ENABLE_MUST_CHECK=y
 CONFIG_LOG_BUF_SHIFT=14
 CONFIG_CROSSCOMPILE=y
 CONFIG_CMDLINE="mem=48M"
-CONFIG_SYS_SUPPORTS_KGDB=y
 
 #
 # Security options

arch/mips/configs/db1500_defconfig

@@ -1392,7 +1392,6 @@ CONFIG_ENABLE_MUST_CHECK=y
 CONFIG_LOG_BUF_SHIFT=14
 CONFIG_CROSSCOMPILE=y
 CONFIG_CMDLINE=""
-CONFIG_SYS_SUPPORTS_KGDB=y
 
 #
 # Security options

arch/mips/configs/db1550_defconfig

@@ -1209,7 +1209,6 @@ CONFIG_ENABLE_MUST_CHECK=y
 CONFIG_LOG_BUF_SHIFT=14
 CONFIG_CROSSCOMPILE=y
 CONFIG_CMDLINE=""
-CONFIG_SYS_SUPPORTS_KGDB=y
 
 #
 # Security options

arch/mips/configs/excite_defconfig

@@ -1269,7 +1269,6 @@ CONFIG_ENABLE_MUST_CHECK=y
 CONFIG_LOG_BUF_SHIFT=14
 CONFIG_CROSSCOMPILE=y
 CONFIG_CMDLINE=""
-CONFIG_SYS_SUPPORTS_KGDB=y
 
 #
 # Security options

arch/mips/configs/ip27_defconfig

@@ -943,7 +943,6 @@ CONFIG_ENABLE_MUST_CHECK=y
 # CONFIG_DEBUG_KERNEL is not set
 CONFIG_CROSSCOMPILE=y
 CONFIG_CMDLINE=""
-CONFIG_SYS_SUPPORTS_KGDB=y
 
 #
 # Security options

arch/mips/configs/msp71xx_defconfig

@@ -1415,8 +1415,6 @@ CONFIG_FORCED_INLINING=y
 CONFIG_CROSSCOMPILE=y
 CONFIG_CMDLINE=""
 # CONFIG_DEBUG_STACK_USAGE is not set
-# CONFIG_KGDB is not set
-CONFIG_SYS_SUPPORTS_KGDB=y
 # CONFIG_RUNTIME_DEBUG is not set
 # CONFIG_MIPS_UNCACHED is not set
 

arch/mips/configs/mtx1_defconfig

@@ -3020,7 +3020,6 @@ CONFIG_MAGIC_SYSRQ=y
 # CONFIG_DEBUG_KERNEL is not set
 CONFIG_CROSSCOMPILE=y
 CONFIG_CMDLINE=""
-CONFIG_SYS_SUPPORTS_KGDB=y
 
 #
 # Security options

arch/mips/configs/pb1100_defconfig

@@ -1085,7 +1085,6 @@ CONFIG_ENABLE_MUST_CHECK=y
 CONFIG_LOG_BUF_SHIFT=14
 CONFIG_CROSSCOMPILE=y
 CONFIG_CMDLINE=""
-CONFIG_SYS_SUPPORTS_KGDB=y
 
 #
 # Security options

arch/mips/configs/pb1500_defconfig

@@ -1202,7 +1202,6 @@ CONFIG_ENABLE_MUST_CHECK=y
 CONFIG_LOG_BUF_SHIFT=14
 CONFIG_CROSSCOMPILE=y
 CONFIG_CMDLINE=""
-CONFIG_SYS_SUPPORTS_KGDB=y
 
 #
 # Security options

arch/mips/configs/pb1550_defconfig

@@ -1195,7 +1195,6 @@ CONFIG_ENABLE_MUST_CHECK=y
 CONFIG_LOG_BUF_SHIFT=14
 CONFIG_CROSSCOMPILE=y
 CONFIG_CMDLINE=""
-CONFIG_SYS_SUPPORTS_KGDB=y
 
 #
 # Security options

arch/mips/configs/pnx8550-jbs_defconfig

@@ -1216,10 +1216,8 @@ CONFIG_DEBUG_MUTEXES=y
 CONFIG_FORCED_INLINING=y
 # CONFIG_RCU_TORTURE_TEST is not set
 CONFIG_CROSSCOMPILE=y
-CONFIG_CMDLINE="console=ttyS1,38400n8 kgdb=ttyS0 root=/dev/nfs ip=bootp"
+CONFIG_CMDLINE="console=ttyS1,38400n8 root=/dev/nfs ip=bootp"
 # CONFIG_DEBUG_STACK_USAGE is not set
-# CONFIG_KGDB is not set
-CONFIG_SYS_SUPPORTS_KGDB=y
 # CONFIG_RUNTIME_DEBUG is not set
 
 #

arch/mips/configs/pnx8550-stb810_defconfig

@@ -1206,10 +1206,8 @@ CONFIG_DEBUG_SLAB=y
 CONFIG_FORCED_INLINING=y
 # CONFIG_RCU_TORTURE_TEST is not set
 CONFIG_CROSSCOMPILE=y
-CONFIG_CMDLINE="console=ttyS1,38400n8 kgdb=ttyS0 root=/dev/nfs ip=bootp"
+CONFIG_CMDLINE="console=ttyS1,38400n8 root=/dev/nfs ip=bootp"
 # CONFIG_DEBUG_STACK_USAGE is not set
-# CONFIG_KGDB is not set
-CONFIG_SYS_SUPPORTS_KGDB=y
 # CONFIG_RUNTIME_DEBUG is not set
 
 #

arch/mips/configs/rbtx49xx_defconfig

@@ -742,7 +742,6 @@ CONFIG_DEBUG_FS=y
 # CONFIG_DEBUG_KERNEL is not set
 # CONFIG_SAMPLES is not set
 CONFIG_CMDLINE=""
-CONFIG_SYS_SUPPORTS_KGDB=y
 
 #
 # Security options

arch/mips/configs/sb1250-swarm_defconfig

@@ -963,7 +963,6 @@ CONFIG_ENABLE_MUST_CHECK=y
 # CONFIG_DEBUG_KERNEL is not set
 # CONFIG_SAMPLES is not set
 CONFIG_CMDLINE=""
-CONFIG_SYS_SUPPORTS_KGDB=y
 # CONFIG_SB1XXX_CORELIS is not set
 
 #

arch/mips/configs/yosemite_defconfig

@@ -827,8 +827,6 @@ CONFIG_FORCED_INLINING=y
 CONFIG_CROSSCOMPILE=y
 CONFIG_CMDLINE=""
 # CONFIG_DEBUG_STACK_USAGE is not set
-# CONFIG_KGDB is not set
-CONFIG_SYS_SUPPORTS_KGDB=y
 # CONFIG_RUNTIME_DEBUG is not set
 
 #

arch/mips/emma2rh/markeins/platform.c

@@ -34,7 +34,6 @@
 #include <asm/bcache.h>
 #include <asm/irq.h>
 #include <asm/reboot.h>
-#include <asm/gdb-stub.h>
 #include <asm/traps.h>
 #include <asm/debug.h>
 

arch/mips/emma2rh/markeins/setup.c

@@ -41,7 +41,6 @@
 #include <asm/bcache.h>
 #include <asm/irq.h>
 #include <asm/reboot.h>
-#include <asm/gdb-stub.h>
 #include <asm/traps.h>
 #include <asm/debug.h>
 

arch/mips/kernel/Makefile

@@ -71,7 +71,7 @@ obj-$(CONFIG_MIPS32_COMPAT)	+= linux32.o ptrace32.o signal32.o
 obj-$(CONFIG_MIPS32_N32)	+= binfmt_elfn32.o scall64-n32.o signal_n32.o
 obj-$(CONFIG_MIPS32_O32)	+= binfmt_elfo32.o scall64-o32.o
 
-obj-$(CONFIG_KGDB)		+= gdb-low.o gdb-stub.o
+obj-$(CONFIG_KGDB)		+= kgdb.o
 obj-$(CONFIG_PROC_FS)		+= proc.o
 
 obj-$(CONFIG_64BIT)		+= cpu-bugs64.o

arch/mips/kernel/gdb-low.S

-/*
- * gdb-low.S contains the low-level trap handler for the GDB stub.
- *
- * Copyright (C) 1995 Andreas Busse
- */
-#include <linux/sys.h>
-
-#include <asm/asm.h>
-#include <asm/errno.h>
-#include <asm/irqflags.h>
-#include <asm/mipsregs.h>
-#include <asm/regdef.h>
-#include <asm/stackframe.h>
-#include <asm/gdb-stub.h>
-
-#ifdef CONFIG_32BIT
-#define DMFC0	mfc0
-#define DMTC0	mtc0
-#define LDC1	lwc1
-#define SDC1	lwc1
-#endif
-#ifdef CONFIG_64BIT
-#define DMFC0	dmfc0
-#define DMTC0	dmtc0
-#define LDC1	ldc1
-#define SDC1	ldc1
-#endif
-
-/*
- * [jsun] We reserves about 2x GDB_FR_SIZE in stack.  The lower (addressed)
- * part is used to store registers and passed to exception handler.
- * The upper part is reserved for "call func" feature where gdb client
- * saves some of the regs, setups call frame and passes args.
- *
- * A trace shows about 200 bytes are used to store about half of all regs.
- * The rest should be big enough for frame setup and passing args.
- */
-
-/*
- * The low level trap handler
- */
-		.align 	5
-		NESTED(trap_low, GDB_FR_SIZE, sp)
-		.set	noat
-		.set 	noreorder
-
-		mfc0	k0, CP0_STATUS
-		sll	k0, 3     		/* extract cu0 bit */
-		bltz	k0, 1f
-		move	k1, sp
-
-		/*
-		 * Called from user mode, go somewhere else.
-		 */
-		mfc0	k0, CP0_CAUSE
-		andi	k0, k0, 0x7c
-#ifdef CONFIG_64BIT
-		dsll	k0, k0, 1
-#endif
-		PTR_L	k1, saved_vectors(k0)
-		jr	k1
-		nop
-1:
-		move	k0, sp
-		PTR_SUBU sp, k1, GDB_FR_SIZE*2	# see comment above
-		LONG_S	k0, GDB_FR_REG29(sp)
-		LONG_S	$2, GDB_FR_REG2(sp)
-
-/*
- * First save the CP0 and special registers
- */
-
-		mfc0	v0, CP0_STATUS
-		LONG_S	v0, GDB_FR_STATUS(sp)
-		mfc0	v0, CP0_CAUSE
-		LONG_S	v0, GDB_FR_CAUSE(sp)
-		DMFC0	v0, CP0_EPC
-		LONG_S	v0, GDB_FR_EPC(sp)
-		DMFC0	v0, CP0_BADVADDR
-		LONG_S	v0, GDB_FR_BADVADDR(sp)
-		mfhi	v0
-		LONG_S	v0, GDB_FR_HI(sp)
-		mflo	v0
-		LONG_S	v0, GDB_FR_LO(sp)
-
-/*
- * Now the integer registers
- */
-
-		LONG_S	zero, GDB_FR_REG0(sp)		/* I know... */
-		LONG_S	$1, GDB_FR_REG1(sp)
-		/* v0 already saved */
-		LONG_S	$3, GDB_FR_REG3(sp)
-		LONG_S	$4, GDB_FR_REG4(sp)
-		LONG_S	$5, GDB_FR_REG5(sp)
-		LONG_S	$6, GDB_FR_REG6(sp)
-		LONG_S	$7, GDB_FR_REG7(sp)
-		LONG_S	$8, GDB_FR_REG8(sp)
-		LONG_S	$9, GDB_FR_REG9(sp)
-		LONG_S	$10, GDB_FR_REG10(sp)
-		LONG_S	$11, GDB_FR_REG11(sp)
-		LONG_S	$12, GDB_FR_REG12(sp)
-		LONG_S	$13, GDB_FR_REG13(sp)
-		LONG_S	$14, GDB_FR_REG14(sp)
-		LONG_S	$15, GDB_FR_REG15(sp)
-		LONG_S	$16, GDB_FR_REG16(sp)
-		LONG_S	$17, GDB_FR_REG17(sp)
-		LONG_S	$18, GDB_FR_REG18(sp)
-		LONG_S	$19, GDB_FR_REG19(sp)
-		LONG_S	$20, GDB_FR_REG20(sp)
-		LONG_S	$21, GDB_FR_REG21(sp)
-		LONG_S	$22, GDB_FR_REG22(sp)
-		LONG_S	$23, GDB_FR_REG23(sp)
-		LONG_S	$24, GDB_FR_REG24(sp)
-		LONG_S	$25, GDB_FR_REG25(sp)
-		LONG_S	$26, GDB_FR_REG26(sp)
-		LONG_S	$27, GDB_FR_REG27(sp)
-		LONG_S	$28, GDB_FR_REG28(sp)
-		/* sp already saved */
-		LONG_S	$30, GDB_FR_REG30(sp)
-		LONG_S	$31, GDB_FR_REG31(sp)
-
-		CLI				/* disable interrupts */
-		TRACE_IRQS_OFF
-
-/*
- * Followed by the floating point registers
- */
-		mfc0	v0, CP0_STATUS		/* FPU enabled? */
-		srl	v0, v0, 16
-		andi	v0, v0, (ST0_CU1 >> 16)
-
-		beqz	v0,2f			/* disabled, skip */
-		 nop
-
-		SDC1	$0, GDB_FR_FPR0(sp)
-		SDC1	$1, GDB_FR_FPR1(sp)
-		SDC1	$2, GDB_FR_FPR2(sp)
-		SDC1	$3, GDB_FR_FPR3(sp)
-		SDC1	$4, GDB_FR_FPR4(sp)
-		SDC1	$5, GDB_FR_FPR5(sp)
-		SDC1	$6, GDB_FR_FPR6(sp)
-		SDC1	$7, GDB_FR_FPR7(sp)
-		SDC1	$8, GDB_FR_FPR8(sp)
-		SDC1	$9, GDB_FR_FPR9(sp)
-		SDC1	$10, GDB_FR_FPR10(sp)
-		SDC1	$11, GDB_FR_FPR11(sp)
-		SDC1	$12, GDB_FR_FPR12(sp)
-		SDC1	$13, GDB_FR_FPR13(sp)
-		SDC1	$14, GDB_FR_FPR14(sp)
-		SDC1	$15, GDB_FR_FPR15(sp)
-		SDC1	$16, GDB_FR_FPR16(sp)
-		SDC1	$17, GDB_FR_FPR17(sp)
-		SDC1	$18, GDB_FR_FPR18(sp)
-		SDC1	$19, GDB_FR_FPR19(sp)
-		SDC1	$20, GDB_FR_FPR20(sp)
-		SDC1	$21, GDB_FR_FPR21(sp)
-		SDC1	$22, GDB_FR_FPR22(sp)
-		SDC1	$23, GDB_FR_FPR23(sp)
-		SDC1	$24, GDB_FR_FPR24(sp)
-		SDC1	$25, GDB_FR_FPR25(sp)
-		SDC1	$26, GDB_FR_FPR26(sp)
-		SDC1	$27, GDB_FR_FPR27(sp)
-		SDC1	$28, GDB_FR_FPR28(sp)
-		SDC1	$29, GDB_FR_FPR29(sp)
-		SDC1	$30, GDB_FR_FPR30(sp)
-		SDC1	$31, GDB_FR_FPR31(sp)
-
-/*
- * FPU control registers
- */
-
-		cfc1	v0, CP1_STATUS
-		LONG_S	v0, GDB_FR_FSR(sp)
-		cfc1	v0, CP1_REVISION
-		LONG_S	v0, GDB_FR_FIR(sp)
-
-/*
- * Current stack frame ptr
- */
-
-2:
-		LONG_S	sp, GDB_FR_FRP(sp)
-
-/*
- * CP0 registers (R4000/R4400 unused registers skipped)
- */
-
-		mfc0	v0, CP0_INDEX
-		LONG_S	v0, GDB_FR_CP0_INDEX(sp)
-		mfc0	v0, CP0_RANDOM
-		LONG_S	v0, GDB_FR_CP0_RANDOM(sp)
-		DMFC0	v0, CP0_ENTRYLO0
-		LONG_S	v0, GDB_FR_CP0_ENTRYLO0(sp)
-		DMFC0	v0, CP0_ENTRYLO1
-		LONG_S	v0, GDB_FR_CP0_ENTRYLO1(sp)
-		DMFC0	v0, CP0_CONTEXT
-		LONG_S	v0, GDB_FR_CP0_CONTEXT(sp)
-		mfc0	v0, CP0_PAGEMASK
-		LONG_S	v0, GDB_FR_CP0_PAGEMASK(sp)
-		mfc0	v0, CP0_WIRED
-		LONG_S	v0, GDB_FR_CP0_WIRED(sp)
-		DMFC0	v0, CP0_ENTRYHI
-		LONG_S	v0, GDB_FR_CP0_ENTRYHI(sp)
-		mfc0	v0, CP0_PRID
-		LONG_S	v0, GDB_FR_CP0_PRID(sp)
-
-		.set	at
-
-/*
- * Continue with the higher level handler
- */
-
-		move	a0,sp
-
-		jal	handle_exception
-		 nop
-
-/*
- * Restore all writable registers, in reverse order
- */
-
-		.set	noat
-
-		LONG_L	v0, GDB_FR_CP0_ENTRYHI(sp)
-		LONG_L	v1, GDB_FR_CP0_WIRED(sp)
-		DMTC0	v0, CP0_ENTRYHI
-		mtc0	v1, CP0_WIRED
-		LONG_L	v0, GDB_FR_CP0_PAGEMASK(sp)
-		LONG_L	v1, GDB_FR_CP0_ENTRYLO1(sp)
-		mtc0	v0, CP0_PAGEMASK
-		DMTC0	v1, CP0_ENTRYLO1
-		LONG_L	v0, GDB_FR_CP0_ENTRYLO0(sp)
-		LONG_L	v1, GDB_FR_CP0_INDEX(sp)
-		DMTC0	v0, CP0_ENTRYLO0
-		LONG_L	v0, GDB_FR_CP0_CONTEXT(sp)
-		mtc0	v1, CP0_INDEX
-		DMTC0	v0, CP0_CONTEXT
-
-
-/*
- * Next, the floating point registers
- */
-		mfc0	v0, CP0_STATUS		/* check if the FPU is enabled */
-		srl	v0, v0, 16
-		andi	v0, v0, (ST0_CU1 >> 16)
-
-		beqz	v0, 3f			/* disabled, skip */
-		 nop
-
-		LDC1	$31, GDB_FR_FPR31(sp)
-		LDC1	$30, GDB_FR_FPR30(sp)
-		LDC1	$29, GDB_FR_FPR29(sp)
-		LDC1	$28, GDB_FR_FPR28(sp)
-		LDC1	$27, GDB_FR_FPR27(sp)
-		LDC1	$26, GDB_FR_FPR26(sp)
-		LDC1	$25, GDB_FR_FPR25(sp)
-		LDC1	$24, GDB_FR_FPR24(sp)
-		LDC1	$23, GDB_FR_FPR23(sp)
-		LDC1	$22, GDB_FR_FPR22(sp)
-		LDC1	$21, GDB_FR_FPR21(sp)
-		LDC1	$20, GDB_FR_FPR20(sp)
-		LDC1	$19, GDB_FR_FPR19(sp)
-		LDC1	$18, GDB_FR_FPR18(sp)
-		LDC1	$17, GDB_FR_FPR17(sp)
-		LDC1	$16, GDB_FR_FPR16(sp)
-		LDC1	$15, GDB_FR_FPR15(sp)
-		LDC1	$14, GDB_FR_FPR14(sp)
-		LDC1	$13, GDB_FR_FPR13(sp)
-		LDC1	$12, GDB_FR_FPR12(sp)
-		LDC1	$11, GDB_FR_FPR11(sp)
-		LDC1	$10, GDB_FR_FPR10(sp)
-		LDC1	$9, GDB_FR_FPR9(sp)
-		LDC1	$8, GDB_FR_FPR8(sp)
-		LDC1	$7, GDB_FR_FPR7(sp)
-		LDC1	$6, GDB_FR_FPR6(sp)
-		LDC1	$5, GDB_FR_FPR5(sp)
-		LDC1	$4, GDB_FR_FPR4(sp)
-		LDC1	$3, GDB_FR_FPR3(sp)
-		LDC1	$2, GDB_FR_FPR2(sp)
-		LDC1	$1, GDB_FR_FPR1(sp)
-		LDC1	$0, GDB_FR_FPR0(sp)
-
-/*
- * Now the CP0 and integer registers
- */
-
-3:
-#ifdef CONFIG_MIPS_MT_SMTC
-		/* Read-modify write of Status must be atomic */
-		mfc0	t2, CP0_TCSTATUS
-		ori	t1, t2, TCSTATUS_IXMT
-		mtc0	t1, CP0_TCSTATUS
-		andi	t2, t2, TCSTATUS_IXMT
-		_ehb
-		DMT	9				# dmt	t1
-		jal	mips_ihb
-		nop
-#endif /* CONFIG_MIPS_MT_SMTC */
-		mfc0	t0, CP0_STATUS
-		ori	t0, 0x1f
-		xori	t0, 0x1f
-		mtc0	t0, CP0_STATUS
-#ifdef CONFIG_MIPS_MT_SMTC
-        	andi    t1, t1, VPECONTROL_TE
-        	beqz    t1, 9f
-		nop
-        	EMT					# emt
-9:
-		mfc0	t1, CP0_TCSTATUS
-		xori	t1, t1, TCSTATUS_IXMT
-		or	t1, t1, t2
-		mtc0	t1, CP0_TCSTATUS
-		_ehb
-#endif /* CONFIG_MIPS_MT_SMTC */
-		LONG_L	v0, GDB_FR_STATUS(sp)
-		LONG_L	v1, GDB_FR_EPC(sp)
-		mtc0	v0, CP0_STATUS
-		DMTC0	v1, CP0_EPC
-		LONG_L	v0, GDB_FR_HI(sp)
-		LONG_L	v1, GDB_FR_LO(sp)
-		mthi	v0
-		mtlo	v1
-		LONG_L	$31, GDB_FR_REG31(sp)
-		LONG_L	$30, GDB_FR_REG30(sp)
-		LONG_L	$28, GDB_FR_REG28(sp)
-		LONG_L	$27, GDB_FR_REG27(sp)
-		LONG_L	$26, GDB_FR_REG26(sp)
-		LONG_L	$25, GDB_FR_REG25(sp)
-		LONG_L	$24, GDB_FR_REG24(sp)
-		LONG_L	$23, GDB_FR_REG23(sp)
-		LONG_L	$22, GDB_FR_REG22(sp)
-		LONG_L	$21, GDB_FR_REG21(sp)
-		LONG_L	$20, GDB_FR_REG20(sp)
-		LONG_L	$19, GDB_FR_REG19(sp)
-		LONG_L	$18, GDB_FR_REG18(sp)
-		LONG_L	$17, GDB_FR_REG17(sp)
-		LONG_L	$16, GDB_FR_REG16(sp)
-		LONG_L	$15, GDB_FR_REG15(sp)
-		LONG_L	$14, GDB_FR_REG14(sp)
-		LONG_L	$13, GDB_FR_REG13(sp)
-		LONG_L	$12, GDB_FR_REG12(sp)
-		LONG_L	$11, GDB_FR_REG11(sp)
-		LONG_L	$10, GDB_FR_REG10(sp)
-		LONG_L	$9, GDB_FR_REG9(sp)
-		LONG_L	$8, GDB_FR_REG8(sp)
-		LONG_L	$7, GDB_FR_REG7(sp)
-		LONG_L	$6, GDB_FR_REG6(sp)
-		LONG_L	$5, GDB_FR_REG5(sp)
-		LONG_L	$4, GDB_FR_REG4(sp)
-		LONG_L	$3, GDB_FR_REG3(sp)
-		LONG_L	$2, GDB_FR_REG2(sp)
-		LONG_L	$1, GDB_FR_REG1(sp)
-#if defined(CONFIG_CPU_R3000) || defined(CONFIG_CPU_TX39XX)
-		LONG_L	k0, GDB_FR_EPC(sp)
-		LONG_L	$29, GDB_FR_REG29(sp)		/* Deallocate stack */
-		jr	k0
-		rfe
-#else
-		LONG_L	sp, GDB_FR_REG29(sp)		/* Deallocate stack */
-
-		.set	mips3
-		eret
-		.set	mips0
-#endif
-		.set	at
-		.set	reorder
-		END(trap_low)
-
-LEAF(kgdb_read_byte)
-4:		lb	t0, (a0)
-		sb	t0, (a1)
-		li	v0, 0
-		jr	ra
-		.section __ex_table,"a"
-		PTR	4b, kgdbfault
-		.previous
-		END(kgdb_read_byte)
-
-LEAF(kgdb_write_byte)
-5:		sb	a0, (a1)
-		li	v0, 0
-		jr	ra
-		.section __ex_table,"a"
-		PTR	5b, kgdbfault
-		.previous
-		END(kgdb_write_byte)
-
-		.type	kgdbfault@function
-		.ent	kgdbfault
-
-kgdbfault:	li	v0, -EFAULT
-		jr	ra
-		.end	kgdbfault

arch/mips/kernel/irq.c

@@ -21,11 +21,16 @@
 #include <linux/sched.h>
 #include <linux/seq_file.h>
 #include <linux/kallsyms.h>
+#include <linux/kgdb.h>
 
 #include <asm/atomic.h>
 #include <asm/system.h>
 #include <asm/uaccess.h>
 
+#ifdef CONFIG_KGDB
+int kgdb_early_setup;
+#endif
+
 static unsigned long irq_map[NR_IRQS / BITS_PER_LONG];
 
 int allocate_irqno(void)
@@ -126,33 +131,22 @@ asmlinkage void spurious_interrupt(void)
 	atomic_inc(&irq_err_count);
 }
 
-#ifdef CONFIG_KGDB
-extern void breakpoint(void);
-extern void set_debug_traps(void);
-
-static int kgdb_flag = 1;
-static int __init nokgdb(char *str)
-{
-	kgdb_flag = 0;
-	return 1;
-}
-__setup("nokgdb", nokgdb);
-#endif
-
 void __init init_IRQ(void)
 {
 	int i;
 
+#ifdef CONFIG_KGDB
+	if (kgdb_early_setup)
+		return;
+#endif
+
 	for (i = 0; i < NR_IRQS; i++)
 		set_irq_noprobe(i);
 
 	arch_init_irq();
 
 #ifdef CONFIG_KGDB
-	if (kgdb_flag) {
-		printk("Wait for gdb client connection ...\n");
-		set_debug_traps();
-		breakpoint();
-	}
+	if (!kgdb_early_setup)
+		kgdb_early_setup = 1;
 #endif
 }

arch/mips/kernel/kgdb.c

+/*
+ *  Originally written by Glenn Engel, Lake Stevens Instrument Division
+ *
+ *  Contributed by HP Systems
+ *
+ *  Modified for Linux/MIPS (and MIPS in general) by Andreas Busse
+ *  Send complaints, suggestions etc. to <andy@waldorf-gmbh.de>
+ *
+ *  Copyright (C) 1995 Andreas Busse
+ *
+ *  Copyright (C) 2003 MontaVista Software Inc.
+ *  Author: Jun Sun, jsun@mvista.com or jsun@junsun.net
+ *
+ *  Copyright (C) 2004-2005 MontaVista Software Inc.
+ *  Author: Manish Lachwani, mlachwani@mvista.com or manish@koffee-break.com
+ *
+ *  Copyright (C) 2007-2008 Wind River Systems, Inc.
+ *  Author/Maintainer: Jason Wessel, jason.wessel@windriver.com
+ *
+ *  This file is licensed under the terms of the GNU General Public License
+ *  version 2. This program is licensed "as is" without any warranty of any
+ *  kind, whether express or implied.
+ */
+
+#include <linux/ptrace.h>		/* for linux pt_regs struct */
+#include <linux/kgdb.h>
+#include <linux/kdebug.h>
+#include <linux/sched.h>
+#include <asm/inst.h>
+#include <asm/fpu.h>
+#include <asm/cacheflush.h>
+#include <asm/processor.h>
+#include <asm/sigcontext.h>
+
+static struct hard_trap_info {
+	unsigned char tt;	/* Trap type code for MIPS R3xxx and R4xxx */
+	unsigned char signo;	/* Signal that we map this trap into */
+} hard_trap_info[] = {
+	{ 6, SIGBUS },		/* instruction bus error */
+	{ 7, SIGBUS },		/* data bus error */
+	{ 9, SIGTRAP },		/* break */
+/*	{ 11, SIGILL },	*/	/* CPU unusable */
+	{ 12, SIGFPE },		/* overflow */
+	{ 13, SIGTRAP },	/* trap */
+	{ 14, SIGSEGV },	/* virtual instruction cache coherency */
+	{ 15, SIGFPE },		/* floating point exception */
+	{ 23, SIGSEGV },	/* watch */
+	{ 31, SIGSEGV },	/* virtual data cache coherency */
+	{ 0, 0}			/* Must be last */
+};
+
+void arch_kgdb_breakpoint(void)
+{
+	__asm__ __volatile__(
+		".globl breakinst\n\t"
+		".set\tnoreorder\n\t"
+		"nop\n"
+		"breakinst:\tbreak\n\t"
+		"nop\n\t"
+		".set\treorder");
+}
+
+static void kgdb_call_nmi_hook(void *ignored)
+{
+	kgdb_nmicallback(raw_smp_processor_id(), (void *)0);
+}
+
+void kgdb_roundup_cpus(unsigned long flags)
+{
+	local_irq_enable();
+	smp_call_function(kgdb_call_nmi_hook, NULL, NULL);
+	local_irq_disable();
+}
+
+static int compute_signal(int tt)
+{
+	struct hard_trap_info *ht;
+
+	for (ht = hard_trap_info; ht->tt && ht->signo; ht++)
+		if (ht->tt == tt)
+			return ht->signo;
+
+	return SIGHUP;		/* default for things we don't know about */
+}
+
+void pt_regs_to_gdb_regs(unsigned long *gdb_regs, struct pt_regs *regs)
+{
+	int reg;
+
+#if (KGDB_GDB_REG_SIZE == 32)
+	u32 *ptr = (u32 *)gdb_regs;
+#else
+	u64 *ptr = (u64 *)gdb_regs;
+#endif
+
+	for (reg = 0; reg < 32; reg++)
+		*(ptr++) = regs->regs[reg];
+
+	*(ptr++) = regs->cp0_status;
+	*(ptr++) = regs->lo;
+	*(ptr++) = regs->hi;
+	*(ptr++) = regs->cp0_badvaddr;
+	*(ptr++) = regs->cp0_cause;
+	*(ptr++) = regs->cp0_epc;
+
+	/* FP REGS */
+	if (!(current && (regs->cp0_status & ST0_CU1)))
+		return;
+
+	save_fp(current);
+	for (reg = 0; reg < 32; reg++)
+		*(ptr++) = current->thread.fpu.fpr[reg];
+}
+
+void gdb_regs_to_pt_regs(unsigned long *gdb_regs, struct pt_regs *regs)
+{
+	int reg;
+
+#if (KGDB_GDB_REG_SIZE == 32)
+	const u32 *ptr = (u32 *)gdb_regs;
+#else
+	const u64 *ptr = (u64 *)gdb_regs;
+#endif
+
+	for (reg = 0; reg < 32; reg++)
+		regs->regs[reg] = *(ptr++);
+
+	regs->cp0_status = *(ptr++);
+	regs->lo = *(ptr++);
+	regs->hi = *(ptr++);
+	regs->cp0_badvaddr = *(ptr++);
+	regs->cp0_cause = *(ptr++);
+	regs->cp0_epc = *(ptr++);
+
+	/* FP REGS from current */
+	if (!(current && (regs->cp0_status & ST0_CU1)))
+		return;
+
+	for (reg = 0; reg < 32; reg++)
+		current->thread.fpu.fpr[reg] = *(ptr++);
+	restore_fp(current);
+}
+
+/*
+ * Similar to regs_to_gdb_regs() except that process is sleeping and so
+ * we may not be able to get all the info.
+ */
+void sleeping_thread_to_gdb_regs(unsigned long *gdb_regs, struct task_struct *p)
+{
+	int reg;
+	struct thread_info *ti = task_thread_info(p);
+	unsigned long ksp = (unsigned long)ti + THREAD_SIZE - 32;
+	struct pt_regs *regs = (struct pt_regs *)ksp - 1;
+#if (KGDB_GDB_REG_SIZE == 32)
+	u32 *ptr = (u32 *)gdb_regs;
+#else
+	u64 *ptr = (u64 *)gdb_regs;
+#endif
+
+	for (reg = 0; reg < 16; reg++)
+		*(ptr++) = regs->regs[reg];
+
+	/* S0 - S7 */
+	for (reg = 16; reg < 24; reg++)
+		*(ptr++) = regs->regs[reg];
+
+	for (reg = 24; reg < 28; reg++)
+		*(ptr++) = 0;
+
+	/* GP, SP, FP, RA */
+	for (reg = 28; reg < 32; reg++)
+		*(ptr++) = regs->regs[reg];
+
+	*(ptr++) = regs->cp0_status;
+	*(ptr++) = regs->lo;
+	*(ptr++) = regs->hi;
+	*(ptr++) = regs->cp0_badvaddr;
+	*(ptr++) = regs->cp0_cause;
+	*(ptr++) = regs->cp0_epc;
+}
+
+/*
+ * Calls linux_debug_hook before the kernel dies. If KGDB is enabled,
+ * then try to fall into the debugger
+ */
+static int kgdb_mips_notify(struct notifier_block *self, unsigned long cmd,
+			    void *ptr)
+{
+	struct die_args *args = (struct die_args *)ptr;
+	struct pt_regs *regs = args->regs;
+	int trap = (regs->cp0_cause & 0x7c) >> 2;
+
+	if (fixup_exception(regs))
+		return NOTIFY_DONE;
+
+	/* Userpace events, ignore. */
+	if (user_mode(regs))
+		return NOTIFY_DONE;
+
+	if (atomic_read(&kgdb_active) != -1)
+		kgdb_nmicallback(smp_processor_id(), regs);
+
+	if (kgdb_handle_exception(trap, compute_signal(trap), 0, regs))
+		return NOTIFY_DONE;
+
+	if (atomic_read(&kgdb_setting_breakpoint))
+		if ((trap == 9) && (regs->cp0_epc == (unsigned long)breakinst))
+			regs->cp0_epc += 4;
+
+	/* In SMP mode, __flush_cache_all does IPI */
+	local_irq_enable();
+	__flush_cache_all();
+
+	return NOTIFY_STOP;
+}
+
+static struct notifier_block kgdb_notifier = {
+	.notifier_call = kgdb_mips_notify,
+};
+
+/*
+ * Handle the 's' and 'c' commands
+ */
+int kgdb_arch_handle_exception(int vector, int signo, int err_code,
+			       char *remcom_in_buffer, char *remcom_out_buffer,
+			       struct pt_regs *regs)
+{
+	char *ptr;
+	unsigned long address;
+	int cpu = smp_processor_id();
+
+	switch (remcom_in_buffer[0]) {
+	case 's':
+	case 'c':
+		/* handle the optional parameter */
+		ptr = &remcom_in_buffer[1];
+		if (kgdb_hex2long(&ptr, &address))
+			regs->cp0_epc = address;
+
+		atomic_set(&kgdb_cpu_doing_single_step, -1);
+		if (remcom_in_buffer[0] == 's')
+			if (kgdb_contthread)
+				atomic_set(&kgdb_cpu_doing_single_step, cpu);
+
+		return 0;
+	}
+
+	return -1;
+}
+
+struct kgdb_arch arch_kgdb_ops;
+
+/*
+ * We use kgdb_early_setup so that functions we need to call now don't
+ * cause trouble when called again later.
+ */
+int kgdb_arch_init(void)
+{
+	union mips_instruction insn = {
+		.r_format = {
+			.opcode = spec_op,
+			.func   = break_op,
+		}
+	};
+	memcpy(arch_kgdb_ops.gdb_bpt_instr, insn.byte, BREAK_INSTR_SIZE);
+
+	register_die_notifier(&kgdb_notifier);
+
+	return 0;
+}
+
+/*
+ *	kgdb_arch_exit - Perform any architecture specific uninitalization.
+ *
+ *	This function will handle the uninitalization of any architecture
+ *	specific callbacks, for dynamic registration and unregistration.
+ */
+void kgdb_arch_exit(void)
+{
+	unregister_die_notifier(&kgdb_notifier);
+}

arch/mips/kernel/traps.c

@@ -23,6 +23,8 @@
 #include <linux/bootmem.h>
 #include <linux/interrupt.h>
 #include <linux/ptrace.h>
+#include <linux/kgdb.h>
+#include <linux/kdebug.h>
 
 #include <asm/bootinfo.h>
 #include <asm/branch.h>
@@ -425,6 +427,10 @@ asmlinkage void do_be(struct pt_regs *regs)
 	printk(KERN_ALERT "%s bus error, epc == %0*lx, ra == %0*lx\n",
 	       data ? "Data" : "Instruction",
 	       field, regs->cp0_epc, field, regs->regs[31]);
+	if (notify_die(DIE_OOPS, "bus error", regs, SIGBUS, 0, 0)
+	    == NOTIFY_STOP)
+		return;
+
 	die_if_kernel("Oops", regs);
 	force_sig(SIGBUS, current);
 }
@@ -623,6 +629,9 @@ asmlinkage void do_fpe(struct pt_regs *regs, unsigned long fcr31)
 {
 	siginfo_t info;
 
+	if (notify_die(DIE_FP, "FP exception", regs, SIGFPE, 0, 0)
+	    == NOTIFY_STOP)
+		return;
 	die_if_kernel("FP exception in kernel code", regs);
 
 	if (fcr31 & FPU_CSR_UNI_X) {
@@ -682,6 +691,9 @@ static void do_trap_or_bp(struct pt_regs *regs, unsigned int code,
 	siginfo_t info;
 	char b[40];
 
+	if (notify_die(DIE_TRAP, str, regs, code, 0, 0) == NOTIFY_STOP)
+		return;
+
 	/*
 	 * A short test says that IRIX 5.3 sends SIGTRAP for all trap
 	 * insns, even for trap and break codes that indicate arithmetic
@@ -762,6 +774,10 @@ asmlinkage void do_ri(struct pt_regs *regs)
 	unsigned int opcode = 0;
 	int status = -1;
 
+	if (notify_die(DIE_RI, "RI Fault", regs, SIGSEGV, 0, 0)
+	    == NOTIFY_STOP)
+		return;
+
 	die_if_kernel("Reserved instruction in kernel code", regs);
 
 	if (unlikely(compute_return_epc(regs) < 0))
@@ -1537,6 +1553,11 @@ void __init trap_init(void)
 	extern char except_vec4;
 	unsigned long i;
 
+#if defined(CONFIG_KGDB)
+	if (kgdb_early_setup)
+		return;	/* Already done */
+#endif
+
 	if (cpu_has_veic || cpu_has_vint)
 		ebase = (unsigned long) alloc_bootmem_low_pages(0x200 + VECTORSPACING*64);
 	else

arch/mips/mm/tlb-r3k.c

@@ -246,10 +246,6 @@ void __init add_wired_entry(unsigned long entrylo0, unsigned long entrylo1,
 		old_pagemask = read_c0_pagemask();
 		w = read_c0_wired();
 		write_c0_wired(w + 1);
-		if (read_c0_wired() != w + 1) {
-			printk("[tlbwired] No WIRED reg?\n");
-			return;
-		}
 		write_c0_index(w << 8);
 		write_c0_pagemask(pagemask);
 		write_c0_entryhi(entryhi);

arch/mips/mti-malta/Makefile

@@ -13,7 +13,6 @@ obj-y				:= malta-amon.o malta-cmdline.o \
 
 obj-$(CONFIG_EARLY_PRINTK)	+= malta-console.o
 obj-$(CONFIG_PCI)		+= malta-pci.o
-obj-$(CONFIG_KGDB)		+= malta-kgdb.o
 
 # FIXME FIXME FIXME
 obj-$(CONFIG_MIPS_MT_SMTC)	+= malta_smtc.o

arch/mips/mti-malta/malta-init.c

@@ -37,15 +37,6 @@
 
 #include <asm/mips-boards/malta.h>
 
-#ifdef CONFIG_KGDB
-extern int rs_kgdb_hook(int, int);
-extern int rs_putDebugChar(char);
-extern char rs_getDebugChar(void);
-extern int saa9730_kgdb_hook(int);
-extern int saa9730_putDebugChar(char);
-extern char saa9730_getDebugChar(void);
-#endif
-
 int prom_argc;
 int *_prom_argv, *_prom_envp;
 
@@ -173,51 +164,6 @@ static void __init console_config(void)
 }
 #endif
 
-#ifdef CONFIG_KGDB
-void __init kgdb_config(void)
-{
-	extern int (*generic_putDebugChar)(char);
-	extern char (*generic_getDebugChar)(void);
-	char *argptr;
-	int line, speed;
-
-	argptr = prom_getcmdline();
-	if ((argptr = strstr(argptr, "kgdb=ttyS")) != NULL) {
-		argptr += strlen("kgdb=ttyS");
-		if (*argptr != '0' && *argptr != '1')
-			printk("KGDB: Unknown serial line /dev/ttyS%c, "
-			       "falling back to /dev/ttyS1\n", *argptr);
-		line = *argptr == '0' ? 0 : 1;
-		printk("KGDB: Using serial line /dev/ttyS%d for session\n", line);
-
-		speed = 0;
-		if (*++argptr == ',')
-		{
-			int c;
-			while ((c = *++argptr) && ('0' <= c && c <= '9'))
-				speed = speed * 10 + c - '0';
-		}
-		{
-			speed = rs_kgdb_hook(line, speed);
-			generic_putDebugChar = rs_putDebugChar;
-			generic_getDebugChar = rs_getDebugChar;
-		}
-
-		pr_info("KGDB: Using serial line /dev/ttyS%d at %d for "
-		        "session, please connect your debugger\n",
-		        line ? 1 : 0, speed);
-
-		{
-			char *s;
-			for (s = "Please connect GDB to this port\r\n"; *s; )
-				generic_putDebugChar(*s++);
-		}
-
-		/* Breakpoint is invoked after interrupts are initialised */
-	}
-}
-#endif
-
 static void __init mips_nmi_setup(void)
 {
 	void *base;

arch/mips/mti-malta/malta-kgdb.c

-/*
- * Carsten Langgaard, carstenl@mips.com
- * Copyright (C) 2000 MIPS Technologies, Inc.  All rights reserved.
- *
- *  This program is free software; you can distribute it and/or modify it
- *  under the terms of the GNU General Public License (Version 2) as
- *  published by the Free Software Foundation.
- *
- *  This program is distributed in the hope it will be useful, but WITHOUT
- *  ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
- *  FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License
- *  for more details.
- *
- *  You should have received a copy of the GNU General Public License along
- *  with this program; if not, write to the Free Software Foundation, Inc.,
- *  59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
- *
- * This is the interface to the remote debugger stub.
- */
-#include <linux/types.h>
-#include <linux/serial.h>
-#include <linux/serialP.h>
-#include <linux/serial_reg.h>
-
-#include <asm/serial.h>
-#include <asm/io.h>
-
-static struct serial_state rs_table[] = {
-	SERIAL_PORT_DFNS	/* Defined in serial.h */
-};
-
-static struct async_struct kdb_port_info = {0};
-
-int (*generic_putDebugChar)(char);
-char (*generic_getDebugChar)(void);
-
-static __inline__ unsigned int serial_in(struct async_struct *info, int offset)
-{
-	return inb(info->port + offset);
-}
-
-static __inline__ void serial_out(struct async_struct *info, int offset,
-				int value)
-{
-	outb(value, info->port+offset);
-}
-
-int rs_kgdb_hook(int tty_no, int speed) {
-	int t;
-	struct serial_state *ser = &rs_table[tty_no];
-
-	kdb_port_info.state = ser;
-	kdb_port_info.magic = SERIAL_MAGIC;
-	kdb_port_info.port = ser->port;
-	kdb_port_info.flags = ser->flags;
-
-	/*
-	 * Clear all interrupts
-	 */
-	serial_in(&kdb_port_info, UART_LSR);
-	serial_in(&kdb_port_info, UART_RX);
-	serial_in(&kdb_port_info, UART_IIR);
-	serial_in(&kdb_port_info, UART_MSR);
-
-	/*
-	 * Now, initialize the UART
-	 */
-	serial_out(&kdb_port_info, UART_LCR, UART_LCR_WLEN8);	/* reset DLAB */
-	if (kdb_port_info.flags & ASYNC_FOURPORT) {
-		kdb_port_info.MCR = UART_MCR_DTR | UART_MCR_RTS;
-		t = UART_MCR_DTR | UART_MCR_OUT1;
-	} else {
-		kdb_port_info.MCR
-			= UART_MCR_DTR | UART_MCR_RTS | UART_MCR_OUT2;
-		t = UART_MCR_DTR | UART_MCR_RTS;
-	}
-
-	kdb_port_info.MCR = t;		/* no interrupts, please */
-	serial_out(&kdb_port_info, UART_MCR, kdb_port_info.MCR);
-
-	/*
-	 * and set the speed of the serial port
-	 */
-	if (speed == 0)
-		speed = 9600;
-
-	t = kdb_port_info.state->baud_base / speed;
-	/* set DLAB */
-	serial_out(&kdb_port_info, UART_LCR, UART_LCR_WLEN8 | UART_LCR_DLAB);
-	serial_out(&kdb_port_info, UART_DLL, t & 0xff);/* LS of divisor */
-	serial_out(&kdb_port_info, UART_DLM, t >> 8);  /* MS of divisor */
-	/* reset DLAB */
-	serial_out(&kdb_port_info, UART_LCR, UART_LCR_WLEN8);
-
-	return speed;
-}
-
-int putDebugChar(char c)
-{
-	return generic_putDebugChar(c);
-}
-
-char getDebugChar(void)
-{
-	return generic_getDebugChar();
-}
-
-int rs_putDebugChar(char c)
-{
-
-	if (!kdb_port_info.state) { 	/* need to init device first */
-		return 0;
-	}
-
-	while ((serial_in(&kdb_port_info, UART_LSR) & UART_LSR_THRE) == 0)
-		;
-
-	serial_out(&kdb_port_info, UART_TX, c);
-
-	return 1;
-}
-
-char rs_getDebugChar(void)
-{
-	if (!kdb_port_info.state) { 	/* need to init device first */
-		return 0;
-	}
-
-	while (!(serial_in(&kdb_port_info, UART_LSR) & 1))
-		;
-
-	return serial_in(&kdb_port_info, UART_RX);
-}

arch/mips/mti-malta/malta-setup.c

@@ -199,10 +199,6 @@ void __init plat_mem_setup(void)
 	 */
 	enable_dma(4);
 
-#ifdef CONFIG_KGDB
-	kgdb_config();
-#endif
-
 #ifdef CONFIG_DMA_COHERENT
 	if (mips_revision_sconid != MIPS_REVISION_SCON_BONITO)
 		panic("Hardware DMA cache coherency not supported");

arch/mips/nxp/pnx8550/common/Makefile

@@ -24,6 +24,5 @@
 
 obj-y := setup.o prom.o int.o reset.o time.o proc.o platform.o
 obj-$(CONFIG_PCI) += pci.o
-obj-$(CONFIG_KGDB) += gdb_hook.o
 
 EXTRA_CFLAGS += -Werror

arch/mips/nxp/pnx8550/common/gdb_hook.c

-/*
- * Carsten Langgaard, carstenl@mips.com
- * Copyright (C) 2000 MIPS Technologies, Inc.  All rights reserved.
- *
- * ########################################################################
- *
- *  This program is free software; you can distribute it and/or modify it
- *  under the terms of the GNU General Public License (Version 2) as
- *  published by the Free Software Foundation.
- *
- *  This program is distributed in the hope it will be useful, but WITHOUT
- *  ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
- *  FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License
- *  for more details.
- *
- *  You should have received a copy of the GNU General Public License along
- *  with this program; if not, write to the Free Software Foundation, Inc.,
- *  59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
- *
- * ########################################################################
- *
- * This is the interface to the remote debugger stub.
- *
- */
-#include <linux/types.h>
-#include <linux/serial.h>
-#include <linux/serialP.h>
-#include <linux/serial_reg.h>
-#include <linux/serial_ip3106.h>
-
-#include <asm/serial.h>
-#include <asm/io.h>
-
-#include <uart.h>
-
-static struct serial_state rs_table[IP3106_NR_PORTS] = {
-};
-static struct async_struct kdb_port_info = {0};
-
-void rs_kgdb_hook(int tty_no)
-{
-	struct serial_state *ser = &rs_table[tty_no];
-
-	kdb_port_info.state = ser;
-	kdb_port_info.magic = SERIAL_MAGIC;
-	kdb_port_info.port  = tty_no;
-	kdb_port_info.flags = ser->flags;
-
-	/*
-	 * Clear all interrupts
-	 */
-	/* Clear all the transmitter FIFO counters (pointer and status) */
-	ip3106_lcr(UART_BASE, tty_no) |= IP3106_UART_LCR_TX_RST;
-	/* Clear all the receiver FIFO counters (pointer and status) */
-	ip3106_lcr(UART_BASE, tty_no) |= IP3106_UART_LCR_RX_RST;
-	/* Clear all interrupts */
-	ip3106_iclr(UART_BASE, tty_no) = IP3106_UART_INT_ALLRX |
-		IP3106_UART_INT_ALLTX;
-
-	/*
-	 * Now, initialize the UART
-	 */
-	ip3106_lcr(UART_BASE, tty_no) = IP3106_UART_LCR_8BIT;
-	ip3106_baud(UART_BASE, tty_no) = 5; // 38400 Baud
-}
-
-int putDebugChar(char c)
-{
-	/* Wait until FIFO not full */
-	while (((ip3106_fifo(UART_BASE, kdb_port_info.port) & IP3106_UART_FIFO_TXFIFO) >> 16) >= 16)
-		;
-	/* Send one char */
-	ip3106_fifo(UART_BASE, kdb_port_info.port) = c;
-
-	return 1;
-}
-
-char getDebugChar(void)
-{
-	char ch;
-
-	/* Wait until there is a char in the FIFO */
-	while (!((ip3106_fifo(UART_BASE, kdb_port_info.port) &
-					IP3106_UART_FIFO_RXFIFO) >> 8))
-		;
-	/* Read one char */
-	ch = ip3106_fifo(UART_BASE, kdb_port_info.port) &
-		IP3106_UART_FIFO_RBRTHR;
-	/* Advance the RX FIFO read pointer */
-	ip3106_lcr(UART_BASE, kdb_port_info.port) |= IP3106_UART_LCR_RX_NEXT;
-	return (ch);
-}
-
-void rs_disable_debug_interrupts(void)
-{
-	ip3106_ien(UART_BASE, kdb_port_info.port) = 0; /* Disable all interrupts */
-}
-
-void rs_enable_debug_interrupts(void)
-{
-	/* Clear all the transmitter FIFO counters (pointer and status) */
-	ip3106_lcr(UART_BASE, kdb_port_info.port) |= IP3106_UART_LCR_TX_RST;
-	/* Clear all the receiver FIFO counters (pointer and status) */
-	ip3106_lcr(UART_BASE, kdb_port_info.port) |= IP3106_UART_LCR_RX_RST;
-	/* Clear all interrupts */
-	ip3106_iclr(UART_BASE, kdb_port_info.port) = IP3106_UART_INT_ALLRX |
-		IP3106_UART_INT_ALLTX;
-	ip3106_ien(UART_BASE, kdb_port_info.port)  = IP3106_UART_INT_ALLRX; /* Enable RX interrupts */
-}

arch/mips/nxp/pnx8550/common/int.c

@@ -34,7 +34,6 @@
 #include <linux/module.h>
 
 #include <asm/io.h>
-#include <asm/gdb-stub.h>
 #include <int.h>
 #include <uart.h>
 

arch/mips/nxp/pnx8550/common/proc.c

@@ -22,7 +22,6 @@
 #include <linux/random.h>
 
 #include <asm/io.h>
-#include <asm/gdb-stub.h>
 #include <int.h>
 #include <uart.h>
 

arch/mips/nxp/pnx8550/common/setup.c

@@ -47,7 +47,6 @@ extern void pnx8550_machine_halt(void);
 extern void pnx8550_machine_power_off(void);
 extern struct resource ioport_resource;
 extern struct resource iomem_resource;
-extern void rs_kgdb_hook(int tty_no);
 extern char *prom_getcmdline(void);
 
 struct resource standard_io_resources[] = {
@@ -142,16 +141,5 @@ void __init plat_mem_setup(void)
 		ip3106_baud(UART_BASE, pnx8550_console_port) = 5;
 	}
 
-#ifdef CONFIG_KGDB
-	argptr = prom_getcmdline();
-	if ((argptr = strstr(argptr, "kgdb=ttyS")) != NULL) {
-		int line;
-		argptr += strlen("kgdb=ttyS");
-		line = *argptr == '0' ? 0 : 1;
-		rs_kgdb_hook(line);
-		pr_info("KGDB: Using ttyS%i for session, "
-		        "please connect your debugger\n", line ? 1 : 0);
-	}
-#endif
 	return;
 }

arch/mips/pci/ops-tx3927.c

@@ -37,45 +37,48 @@
 #include <linux/pci.h>
 #include <linux/kernel.h>
 #include <linux/init.h>
+#include <linux/interrupt.h>
 
 #include <asm/addrspace.h>
+#include <asm/txx9irq.h>
+#include <asm/txx9/pci.h>
 #include <asm/txx9/tx3927.h>
 
-static inline int mkaddr(unsigned char bus, unsigned char dev_fn,
-	unsigned char where)
+static int mkaddr(struct pci_bus *bus, unsigned char devfn, unsigned char where)
 {
-	if (bus == 0 && dev_fn >= PCI_DEVFN(TX3927_PCIC_MAX_DEVNU, 0))
-		return PCIBIOS_DEVICE_NOT_FOUND;
-
-	tx3927_pcicptr->ica = ((bus & 0xff) << 0x10) |
-	                      ((dev_fn & 0xff) << 0x08) |
-	                      (where & 0xfc);
+	if (bus->parent == NULL &&
+	    devfn >= PCI_DEVFN(TX3927_PCIC_MAX_DEVNU, 0))
+		return -1;
+	tx3927_pcicptr->ica =
+		((bus->number & 0xff) << 0x10) |
+		((devfn & 0xff) << 0x08) |
+		(where & 0xfc) | (bus->parent ? 1 : 0);
 
 	/* clear M_ABORT and Disable M_ABORT Int. */
 	tx3927_pcicptr->pcistat |= PCI_STATUS_REC_MASTER_ABORT;
 	tx3927_pcicptr->pcistatim &= ~PCI_STATUS_REC_MASTER_ABORT;
-
-	return PCIBIOS_SUCCESSFUL;
+	return 0;
 }
 
 static inline int check_abort(void)
 {
-	if (tx3927_pcicptr->pcistat & PCI_STATUS_REC_MASTER_ABORT)
+	if (tx3927_pcicptr->pcistat & PCI_STATUS_REC_MASTER_ABORT) {
 		tx3927_pcicptr->pcistat |= PCI_STATUS_REC_MASTER_ABORT;
 		tx3927_pcicptr->pcistatim |= PCI_STATUS_REC_MASTER_ABORT;
+		/* flush write buffer */
+		iob();
 		return PCIBIOS_DEVICE_NOT_FOUND;
-
+	}
 	return PCIBIOS_SUCCESSFUL;
 }
 
 static int tx3927_pci_read_config(struct pci_bus *bus, unsigned int devfn,
 	int where, int size, u32 * val)
 {
-	int ret;
-
-	ret = mkaddr(bus->number, devfn, where);
-	if (ret)
-		return ret;
+	if (mkaddr(bus, devfn, where)) {
+		*val = 0xffffffff;
+		return PCIBIOS_DEVICE_NOT_FOUND;
+	}
 
 	switch (size) {
 	case 1:
@@ -97,11 +100,8 @@ static int tx3927_pci_read_config(struct pci_bus *bus, unsigned int devfn,
 static int tx3927_pci_write_config(struct pci_bus *bus, unsigned int devfn,
 	int where, int size, u32 val)
 {
-	int ret;
-
-	ret = mkaddr(bus->number, devfn, where);
-	if (ret)
-		return ret;
+	if (mkaddr(bus, devfn, where))
+		return PCIBIOS_DEVICE_NOT_FOUND;
 
 	switch (size) {
 	case 1:
@@ -117,11 +117,6 @@ static int tx3927_pci_write_config(struct pci_bus *bus, unsigned int devfn,
 		tx3927_pcicptr->icd = cpu_to_le32(val);
 	}
 
-	if (tx3927_pcicptr->pcistat & PCI_STATUS_REC_MASTER_ABORT)
-		tx3927_pcicptr->pcistat |= PCI_STATUS_REC_MASTER_ABORT;
-		tx3927_pcicptr->pcistatim |= PCI_STATUS_REC_MASTER_ABORT;
-		return PCIBIOS_DEVICE_NOT_FOUND;
-
 	return check_abort();
 }
 
@@ -202,3 +197,34 @@ void __init tx3927_pcic_setup(struct pci_controller *channel,
 		PCI_COMMAND_PARITY | PCI_COMMAND_SERR;
 	local_irq_restore(flags);
 }
+
+static irqreturn_t tx3927_pcierr_interrupt(int irq, void *dev_id)
+{
+	struct pt_regs *regs = get_irq_regs();
+
+	if (txx9_pci_err_action != TXX9_PCI_ERR_IGNORE) {
+		printk(KERN_WARNING "PCI error interrupt at 0x%08lx.\n",
+		       regs->cp0_epc);
+		printk(KERN_WARNING "pcistat:%02x, lbstat:%04lx\n",
+		       tx3927_pcicptr->pcistat, tx3927_pcicptr->lbstat);
+	}
+	if (txx9_pci_err_action != TXX9_PCI_ERR_PANIC) {
+		/* clear all pci errors */
+		tx3927_pcicptr->pcistat |= TX3927_PCIC_PCISTATIM_ALL;
+		tx3927_pcicptr->istat = TX3927_PCIC_IIM_ALL;
+		tx3927_pcicptr->tstat = TX3927_PCIC_TIM_ALL;
+		tx3927_pcicptr->lbstat = TX3927_PCIC_LBIM_ALL;
+		return IRQ_HANDLED;
+	}
+	console_verbose();
+	panic("PCI error.");
+}
+
+void __init tx3927_setup_pcierr_irq(void)
+{
+	if (request_irq(TXX9_IRQ_BASE + TX3927_IR_PCI,
+			tx3927_pcierr_interrupt,
+			IRQF_DISABLED, "PCI error",
+			(void *)TX3927_PCIC_REG))
+		printk(KERN_WARNING "Failed to request irq for PCIERR\n");
+}

arch/mips/pci/ops-tx4927.c

@@ -16,6 +16,8 @@
  * option) any later version.
  */
 #include <linux/kernel.h>
+#include <linux/interrupt.h>
+#include <asm/txx9/pci.h>
 #include <asm/txx9/tx4927pcic.h>
 
 static struct {
@@ -85,6 +87,8 @@ static int check_abort(struct tx4927_pcic_reg __iomem *pcicptr)
 		__raw_writel((__raw_readl(&pcicptr->pcistatus) & 0x0000ffff)
 			     | (PCI_STATUS_REC_MASTER_ABORT << 16),
 			     &pcicptr->pcistatus);
+		/* flush write buffer */
+		iob();
 		code = PCIBIOS_DEVICE_NOT_FOUND;
 	}
 	return code;
@@ -192,6 +196,28 @@ static struct {
 	.gbwc = 0xfe0,	/* 4064 GBUSCLK for CCFG.GTOT=0b11 */
 };
 
+char *__devinit tx4927_pcibios_setup(char *str)
+{
+	unsigned long val;
+
+	if (!strncmp(str, "trdyto=", 7)) {
+		if (strict_strtoul(str + 7, 0, &val) == 0)
+			tx4927_pci_opts.trdyto = val;
+		return NULL;
+	}
+	if (!strncmp(str, "retryto=", 8)) {
+		if (strict_strtoul(str + 8, 0, &val) == 0)
+			tx4927_pci_opts.retryto = val;
+		return NULL;
+	}
+	if (!strncmp(str, "gbwc=", 5)) {
+		if (strict_strtoul(str + 5, 0, &val) == 0)
+			tx4927_pci_opts.gbwc = val;
+		return NULL;
+	}
+	return str;
+}
+
 void __init tx4927_pcic_setup(struct tx4927_pcic_reg __iomem *pcicptr,
 			      struct pci_controller *channel, int extarb)
 {
@@ -406,3 +432,95 @@ void tx4927_report_pcic_status(void)
 			tx4927_report_pcic_status1(pcicptrs[i].pcicptr);
 	}
 }
+
+static void tx4927_dump_pcic_settings1(struct tx4927_pcic_reg __iomem *pcicptr)
+{
+	int i;
+	__u32 __iomem *preg = (__u32 __iomem *)pcicptr;
+
+	printk(KERN_INFO "tx4927 pcic (0x%p) settings:", pcicptr);
+	for (i = 0; i < sizeof(struct tx4927_pcic_reg); i += 4, preg++) {
+		if (i % 32 == 0) {
+			printk(KERN_CONT "\n");
+			printk(KERN_INFO "%04x:", i);
+		}
+		/* skip registers with side-effects */
+		if (i == offsetof(struct tx4927_pcic_reg, g2pintack)
+		    || i == offsetof(struct tx4927_pcic_reg, g2pspc)
+		    || i == offsetof(struct tx4927_pcic_reg, g2pcfgadrs)
+		    || i == offsetof(struct tx4927_pcic_reg, g2pcfgdata)) {
+			printk(KERN_CONT " XXXXXXXX");
+			continue;
+		}
+		printk(KERN_CONT " %08x", __raw_readl(preg));
+	}
+	printk(KERN_CONT "\n");
+}
+
+void tx4927_dump_pcic_settings(void)
+{
+	int i;
+
+	for (i = 0; i < ARRAY_SIZE(pcicptrs); i++) {
+		if (pcicptrs[i].pcicptr)
+			tx4927_dump_pcic_settings1(pcicptrs[i].pcicptr);
+	}
+}
+
+irqreturn_t tx4927_pcierr_interrupt(int irq, void *dev_id)
+{
+	struct pt_regs *regs = get_irq_regs();
+	struct tx4927_pcic_reg __iomem *pcicptr =
+		(struct tx4927_pcic_reg __iomem *)(unsigned long)dev_id;
+
+	if (txx9_pci_err_action != TXX9_PCI_ERR_IGNORE) {
+		printk(KERN_WARNING "PCIERR interrupt at 0x%0*lx\n",
+		       (int)(2 * sizeof(unsigned long)), regs->cp0_epc);
+		tx4927_report_pcic_status1(pcicptr);
+	}
+	if (txx9_pci_err_action != TXX9_PCI_ERR_PANIC) {
+		/* clear all pci errors */
+		__raw_writel((__raw_readl(&pcicptr->pcistatus) & 0x0000ffff)
+			     | (TX4927_PCIC_PCISTATUS_ALL << 16),
+			     &pcicptr->pcistatus);
+		__raw_writel(TX4927_PCIC_G2PSTATUS_ALL, &pcicptr->g2pstatus);
+		__raw_writel(TX4927_PCIC_PBASTATUS_ALL, &pcicptr->pbastatus);
+		__raw_writel(TX4927_PCIC_PCICSTATUS_ALL, &pcicptr->pcicstatus);
+		return IRQ_HANDLED;
+	}
+	console_verbose();
+	tx4927_dump_pcic_settings1(pcicptr);
+	panic("PCI error.");
+}
+
+#ifdef CONFIG_TOSHIBA_FPCIB0
+static void __init tx4927_quirk_slc90e66_bridge(struct pci_dev *dev)
+{
+	struct tx4927_pcic_reg __iomem *pcicptr = pci_bus_to_pcicptr(dev->bus);
+
+	if (!pcicptr)
+		return;
+	if (__raw_readl(&pcicptr->pbacfg) & TX4927_PCIC_PBACFG_PBAEN) {
+		/* Reset Bus Arbiter */
+		__raw_writel(TX4927_PCIC_PBACFG_RPBA, &pcicptr->pbacfg);
+		/*
+		 * swap reqBP and reqXP (raise priority of SLC90E66).
+		 * SLC90E66(PCI-ISA bridge) is connected to REQ2 on
+		 * PCI Backplane board.
+		 */
+		__raw_writel(0x72543610, &pcicptr->pbareqport);
+		__raw_writel(0, &pcicptr->pbabm);
+		/* Use Fixed ParkMaster (required by SLC90E66) */
+		__raw_writel(TX4927_PCIC_PBACFG_FIXPA, &pcicptr->pbacfg);
+		/* Enable Bus Arbiter */
+		__raw_writel(TX4927_PCIC_PBACFG_FIXPA |
+			     TX4927_PCIC_PBACFG_PBAEN,
+			     &pcicptr->pbacfg);
+		printk(KERN_INFO "PCI: Use Fixed Park Master (REQPORT %08x)\n",
+		       __raw_readl(&pcicptr->pbareqport));
+	}
+}
+#define PCI_DEVICE_ID_EFAR_SLC90E66_0 0x9460
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_EFAR, PCI_DEVICE_ID_EFAR_SLC90E66_0,
+	tx4927_quirk_slc90e66_bridge);
+#endif

arch/mips/pci/pci-tx4927.c

@@ -15,6 +15,7 @@
 #include <linux/init.h>
 #include <linux/pci.h>
 #include <linux/kernel.h>
+#include <linux/interrupt.h>
 #include <asm/txx9/generic.h>
 #include <asm/txx9/tx4927.h>
 
@@ -81,3 +82,12 @@ int __init tx4927_pciclk66_setup(void)
 		pciclk = -1;
 	return pciclk;
 }
+
+void __init tx4927_setup_pcierr_irq(void)
+{
+	if (request_irq(TXX9_IRQ_BASE + TX4927_IR_PCIERR,
+			tx4927_pcierr_interrupt,
+			IRQF_DISABLED, "PCI error",
+			(void *)TX4927_PCIC_REG))
+		printk(KERN_WARNING "Failed to request irq for PCIERR\n");
+}

arch/mips/pci/pci-tx4938.c

@@ -15,6 +15,7 @@
 #include <linux/init.h>
 #include <linux/pci.h>
 #include <linux/kernel.h>
+#include <linux/interrupt.h>
 #include <asm/txx9/generic.h>
 #include <asm/txx9/tx4938.h>
 
@@ -132,3 +133,12 @@ int tx4938_pcic1_map_irq(const struct pci_dev *dev, u8 slot)
 	}
 	return -1;
 }
+
+void __init tx4938_setup_pcierr_irq(void)
+{
+	if (request_irq(TXX9_IRQ_BASE + TX4938_IR_PCIERR,
+			tx4927_pcierr_interrupt,
+			IRQF_DISABLED, "PCI error",
+			(void *)TX4927_PCIC_REG))
+		printk(KERN_WARNING "Failed to request irq for PCIERR\n");
+}

arch/mips/pci/pci.c

@@ -328,7 +328,11 @@ EXPORT_SYMBOL(PCIBIOS_MIN_IO);
 EXPORT_SYMBOL(PCIBIOS_MIN_MEM);
 #endif
 
-char *pcibios_setup(char *str)
+char * (*pcibios_plat_setup)(char *str) __devinitdata;
+
+char *__devinit pcibios_setup(char *str)
 {
+	if (pcibios_plat_setup)
+		return pcibios_plat_setup(str);
 	return str;
 }

arch/mips/pmc-sierra/msp71xx/msp_serial.c

@@ -38,68 +38,6 @@
 #include <msp_int.h>
 #include <msp_regs.h>
 
-#ifdef CONFIG_KGDB
-/*
- * kgdb uses serial port 1 so the console can remain on port 0.
- * To use port 0 change the definition to read as follows:
- * #define DEBUG_PORT_BASE KSEG1ADDR(MSP_UART0_BASE)
- */
-#define DEBUG_PORT_BASE KSEG1ADDR(MSP_UART1_BASE)
-
-int putDebugChar(char c)
-{
-	volatile uint32_t *uart = (volatile uint32_t *)DEBUG_PORT_BASE;
-	uint32_t val = (uint32_t)c;
-
-	local_irq_disable();
-	while( !(uart[5] & 0x20) ); /* Wait for TXRDY */
-	uart[0] = val;
-	while( !(uart[5] & 0x20) ); /* Wait for TXRDY */
-	local_irq_enable();
-
-	return 1;
-}
-
-char getDebugChar(void)
-{
-	volatile uint32_t *uart = (volatile uint32_t *)DEBUG_PORT_BASE;
-	uint32_t val;
-
-	while( !(uart[5] & 0x01) ); /* Wait for RXRDY */
-	val = uart[0];
-
-	return (char)val;
-}
-
-void initDebugPort(unsigned int uartclk, unsigned int baudrate)
-{
-	unsigned int baud_divisor = (uartclk + 8 * baudrate)/(16 * baudrate);
-
-	/* Enable FIFOs */
-	writeb(UART_FCR_ENABLE_FIFO | UART_FCR_CLEAR_RCVR |
-			UART_FCR_CLEAR_XMIT | UART_FCR_TRIGGER_4,
-		(char *)DEBUG_PORT_BASE + (UART_FCR * 4));
-
-	/* Select brtc divisor */
-	writeb(UART_LCR_DLAB, (char *)DEBUG_PORT_BASE + (UART_LCR * 4));
-
-	/* Store divisor lsb */
-	writeb(baud_divisor, (char *)DEBUG_PORT_BASE + (UART_TX * 4));
-
-	/* Store divisor msb */
-	writeb(baud_divisor >> 8, (char *)DEBUG_PORT_BASE + (UART_IER * 4));
-
-	/* Set 8N1 mode */
-	writeb(UART_LCR_WLEN8, (char *)DEBUG_PORT_BASE + (UART_LCR * 4));
-
-	/* Disable flow control */
-	writeb(0, (char *)DEBUG_PORT_BASE + (UART_MCR * 4));
-
-	/* Disable receive interrupt(!) */
-	writeb(0, (char *)DEBUG_PORT_BASE + (UART_IER * 4));
-}
-#endif
-
 void __init msp_serial_setup(void)
 {
 	char    *s;
@@ -139,17 +77,6 @@ void __init msp_serial_setup(void)
 		case MACH_MSP7120_FPGA:
 			/* Enable UART1 on MSP4200 and MSP7120 */
 			*GPIO_CFG2_REG = 0x00002299;
-
-#ifdef CONFIG_KGDB
-			/* Initialize UART1 for kgdb since PMON doesn't */
-			if( DEBUG_PORT_BASE == KSEG1ADDR(MSP_UART1_BASE) ) {
-				if( mips_machtype == MACH_MSP4200_FPGA
-				 || mips_machtype == MACH_MSP7120_FPGA )
-					initDebugPort(uartclk, 19200);
-				else
-					initDebugPort(uartclk, 57600);
-			}
-#endif
 			break;
 
 		default:

arch/mips/pmc-sierra/yosemite/Makefile

@@ -4,7 +4,6 @@
 
 obj-y    += irq.o prom.o py-console.o setup.o
 
-obj-$(CONFIG_KGDB)		+= dbg_io.o
 obj-$(CONFIG_SMP)		+= smp.o
 
 EXTRA_CFLAGS += -Werror

arch/mips/pmc-sierra/yosemite/dbg_io.c

-/*
- * Copyright 2003 PMC-Sierra
- * Author: Manish Lachwani (lachwani@pmc-sierra.com)
- *
- *  This program is free software; you can redistribute  it and/or modify it
- *  under  the terms of  the GNU General  Public License as published by the
- *  Free Software Foundation;  either version 2 of the  License, or (at your
- *  option) any later version.
- *
- *  THIS  SOFTWARE  IS PROVIDED   ``AS  IS'' AND   ANY  EXPRESS OR IMPLIED
- *  WARRANTIES,   INCLUDING, BUT NOT  LIMITED  TO, THE IMPLIED WARRANTIES OF
- *  MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.  IN
- *  NO  EVENT  SHALL   THE AUTHOR  BE    LIABLE FOR ANY   DIRECT, INDIRECT,
- *  INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
- *  NOT LIMITED   TO, PROCUREMENT OF  SUBSTITUTE GOODS  OR SERVICES; LOSS OF
- *  USE, DATA,  OR PROFITS; OR  BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
- *  ANY THEORY OF LIABILITY, WHETHER IN  CONTRACT, STRICT LIABILITY, OR TORT
- *  (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
- *  THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- *  You should have received a copy of the  GNU General Public License along
- *  with this program; if not, write  to the Free Software Foundation, Inc.,
- *  675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-/*
- * Support for KGDB for the Yosemite board. We make use of single serial
- * port to be used for KGDB as well as console. The second serial port
- * seems to be having a problem. Single IRQ is allocated for both the
- * ports. Hence, the interrupt routing code needs to figure out whether
- * the interrupt came from channel A or B.
- */
-
-#include <asm/serial.h>
-
-/*
- * Baud rate, Parity, Data and Stop bit settings for the
- * serial port on the Yosemite. Note that the Early printk
- * patch has been added. So, we should be all set to go
- */
-#define	YOSEMITE_BAUD_2400	2400
-#define	YOSEMITE_BAUD_4800	4800
-#define	YOSEMITE_BAUD_9600	9600
-#define	YOSEMITE_BAUD_19200	19200
-#define	YOSEMITE_BAUD_38400	38400
-#define	YOSEMITE_BAUD_57600	57600
-#define	YOSEMITE_BAUD_115200	115200
-
-#define	YOSEMITE_PARITY_NONE	0
-#define	YOSEMITE_PARITY_ODD	0x08
-#define	YOSEMITE_PARITY_EVEN	0x18
-#define	YOSEMITE_PARITY_MARK	0x28
-#define	YOSEMITE_PARITY_SPACE	0x38
-
-#define	YOSEMITE_DATA_5BIT	0x0
-#define	YOSEMITE_DATA_6BIT	0x1
-#define	YOSEMITE_DATA_7BIT	0x2
-#define	YOSEMITE_DATA_8BIT	0x3
-
-#define	YOSEMITE_STOP_1BIT	0x0
-#define	YOSEMITE_STOP_2BIT	0x4
-
-/* This is crucial */
-#define	SERIAL_REG_OFS		0x1
-
-#define	SERIAL_RCV_BUFFER	0x0
-#define	SERIAL_TRANS_HOLD	0x0
-#define	SERIAL_SEND_BUFFER	0x0
-#define	SERIAL_INTR_ENABLE	(1 * SERIAL_REG_OFS)
-#define	SERIAL_INTR_ID		(2 * SERIAL_REG_OFS)
-#define	SERIAL_DATA_FORMAT	(3 * SERIAL_REG_OFS)
-#define	SERIAL_LINE_CONTROL	(3 * SERIAL_REG_OFS)
-#define	SERIAL_MODEM_CONTROL	(4 * SERIAL_REG_OFS)
-#define	SERIAL_RS232_OUTPUT	(4 * SERIAL_REG_OFS)
-#define	SERIAL_LINE_STATUS	(5 * SERIAL_REG_OFS)
-#define	SERIAL_MODEM_STATUS	(6 * SERIAL_REG_OFS)
-#define	SERIAL_RS232_INPUT	(6 * SERIAL_REG_OFS)
-#define	SERIAL_SCRATCH_PAD	(7 * SERIAL_REG_OFS)
-
-#define	SERIAL_DIVISOR_LSB	(0 * SERIAL_REG_OFS)
-#define	SERIAL_DIVISOR_MSB	(1 * SERIAL_REG_OFS)
-
-/*
- * Functions to READ and WRITE to serial port 0
- */
-#define	SERIAL_READ(ofs)		(*((volatile unsigned char*)	\
-					(TITAN_SERIAL_BASE + ofs)))
-
-#define	SERIAL_WRITE(ofs, val)		((*((volatile unsigned char*)	\
-					(TITAN_SERIAL_BASE + ofs))) = val)
-
-/*
- * Functions to READ and WRITE to serial port 1
- */
-#define	SERIAL_READ_1(ofs)		(*((volatile unsigned char*)	\
-					(TITAN_SERIAL_BASE_1 + ofs)))
-
-#define	SERIAL_WRITE_1(ofs, val)	((*((volatile unsigned char*)	\
-					(TITAN_SERIAL_BASE_1 + ofs))) = val)
-
-/*
- * Second serial port initialization
- */
-void init_second_port(void)
-{
-	/* Disable Interrupts */
-	SERIAL_WRITE_1(SERIAL_LINE_CONTROL, 0x0);
-	SERIAL_WRITE_1(SERIAL_INTR_ENABLE, 0x0);
-
-	{
-		unsigned int divisor;
-
-		SERIAL_WRITE_1(SERIAL_LINE_CONTROL, 0x80);
-		divisor = TITAN_SERIAL_BASE_BAUD / YOSEMITE_BAUD_115200;
-		SERIAL_WRITE_1(SERIAL_DIVISOR_LSB, divisor & 0xff);
-
-		SERIAL_WRITE_1(SERIAL_DIVISOR_MSB,
-			       (divisor & 0xff00) >> 8);
-		SERIAL_WRITE_1(SERIAL_LINE_CONTROL, 0x0);
-	}
-
-	SERIAL_WRITE_1(SERIAL_DATA_FORMAT, YOSEMITE_DATA_8BIT |
-		       YOSEMITE_PARITY_NONE | YOSEMITE_STOP_1BIT);
-
-	/* Enable Interrupts */
-	SERIAL_WRITE_1(SERIAL_INTR_ENABLE, 0xf);
-}
-
-/* Initialize the serial port for KGDB debugging */
-void debugInit(unsigned int baud, unsigned char data, unsigned char parity,
-	       unsigned char stop)
-{
-	/* Disable Interrupts */
-	SERIAL_WRITE(SERIAL_LINE_CONTROL, 0x0);
-	SERIAL_WRITE(SERIAL_INTR_ENABLE, 0x0);
-
-	{
-		unsigned int divisor;
-
-		SERIAL_WRITE(SERIAL_LINE_CONTROL, 0x80);
-
-		divisor = TITAN_SERIAL_BASE_BAUD / baud;
-		SERIAL_WRITE(SERIAL_DIVISOR_LSB, divisor & 0xff);
-
-		SERIAL_WRITE(SERIAL_DIVISOR_MSB, (divisor & 0xff00) >> 8);
-		SERIAL_WRITE(SERIAL_LINE_CONTROL, 0x0);
-	}
-
-	SERIAL_WRITE(SERIAL_DATA_FORMAT, data | parity | stop);
-}
-
-static int remoteDebugInitialized = 0;
-
-unsigned char getDebugChar(void)
-{
-	if (!remoteDebugInitialized) {
-		remoteDebugInitialized = 1;
-		debugInit(YOSEMITE_BAUD_115200,
-			  YOSEMITE_DATA_8BIT,
-			  YOSEMITE_PARITY_NONE, YOSEMITE_STOP_1BIT);
-	}
-
-	while ((SERIAL_READ(SERIAL_LINE_STATUS) & 0x1) == 0);
-	return SERIAL_READ(SERIAL_RCV_BUFFER);
-}
-
-int putDebugChar(unsigned char byte)
-{
-	if (!remoteDebugInitialized) {
-		remoteDebugInitialized = 1;
-		debugInit(YOSEMITE_BAUD_115200,
-			  YOSEMITE_DATA_8BIT,
-			  YOSEMITE_PARITY_NONE, YOSEMITE_STOP_1BIT);
-	}
-
-	while ((SERIAL_READ(SERIAL_LINE_STATUS) & 0x20) == 0);
-	SERIAL_WRITE(SERIAL_SEND_BUFFER, byte);
-
-	return 1;
-}

arch/mips/pmc-sierra/yosemite/irq.c

@@ -141,10 +141,6 @@ asmlinkage void plat_irq_dispatch(void)
 	}
 }
 
-#ifdef CONFIG_KGDB
-extern void init_second_port(void);
-#endif
-
 /*
  * Initialize the next level interrupt handler
  */
@@ -156,11 +152,6 @@ void __init arch_init_irq(void)
 	rm7k_cpu_irq_init();
 	rm9k_cpu_irq_init();
 
-#ifdef CONFIG_KGDB
-	/* At this point, initialize the second serial port */
-	init_second_port();
-#endif
-
 #ifdef CONFIG_GDB_CONSOLE
 	register_gdb_console();
 #endif

arch/mips/rb532/gpio.c

@@ -64,7 +64,8 @@ static struct resource rb532_dev3_ctl_res[] = {
 
 void set_434_reg(unsigned reg_offs, unsigned bit, unsigned len, unsigned val)
 {
-	unsigned flags, data;
+	unsigned long flags;
+	unsigned data;
 	unsigned i = 0;
 
 	spin_lock_irqsave(&dev3.lock, flags);
@@ -90,7 +91,7 @@ EXPORT_SYMBOL(get_434_reg);
 
 void set_latch_u5(unsigned char or_mask, unsigned char nand_mask)
 {
-	unsigned flags;
+	unsigned long flags;
 
 	spin_lock_irqsave(&dev3.lock, flags);
 

arch/mips/rb532/time.c

@@ -49,8 +49,8 @@ static unsigned long __init cal_r4koff(void)
 
 void __init plat_time_init(void)
 {
-	unsigned int est_freq, flags;
-	unsigned long r4k_offset;
+	unsigned int est_freq;
+	unsigned long flags, r4k_offset;
 
 	local_irq_save(flags);
 

arch/mips/sgi-ip22/ip22-setup.c

@@ -20,7 +20,6 @@
 #include <asm/irq.h>
 #include <asm/reboot.h>
 #include <asm/time.h>
-#include <asm/gdb-stub.h>
 #include <asm/io.h>
 #include <asm/traps.h>
 #include <asm/sgialib.h>
@@ -81,30 +80,6 @@ void __init plat_mem_setup(void)
 		add_preferred_console("arc", 0, NULL);
 	}
 
-#ifdef CONFIG_KGDB
-	{
-	char *kgdb_ttyd = prom_getcmdline();
-
-	if ((kgdb_ttyd = strstr(kgdb_ttyd, "kgdb=ttyd")) != NULL) {
-		int line;
-		kgdb_ttyd += strlen("kgdb=ttyd");
-		if (*kgdb_ttyd != '1' && *kgdb_ttyd != '2')
-			printk(KERN_INFO "KGDB: Uknown serial line /dev/ttyd%c"
-			       ", falling back to /dev/ttyd1\n", *kgdb_ttyd);
-		line = *kgdb_ttyd == '2' ? 0 : 1;
-		printk(KERN_INFO "KGDB: Using serial line /dev/ttyd%d for "
-		       "session\n", line ? 1 : 2);
-		rs_kgdb_hook(line);
-
-		printk(KERN_INFO "KGDB: Using serial line /dev/ttyd%d for "
-		       "session, please connect your debugger\n", line ? 1:2);
-
-		kgdb_enabled = 1;
-		/* Breakpoints and stuff are in sgi_irq_setup() */
-	}
-	}
-#endif
-
 #if defined(CONFIG_VT) && defined(CONFIG_SGI_NEWPORT_CONSOLE)
 	{
 		ULONG *gfxinfo;

arch/mips/sgi-ip27/Makefile

@@ -7,7 +7,6 @@ obj-y	:= ip27-berr.o ip27-irq.o ip27-init.o ip27-klconfig.o ip27-klnuma.o \
 	   ip27-xtalk.o
 
 obj-$(CONFIG_EARLY_PRINTK)	+= ip27-console.o
-obj-$(CONFIG_KGDB)		+= ip27-dbgio.o
 obj-$(CONFIG_SMP)		+= ip27-smp.o
 
 EXTRA_CFLAGS += -Werror

arch/mips/sgi-ip27/ip27-dbgio.c

-/*
- *  This program is free software; you can redistribute  it and/or modify it
- *  under  the terms of  the GNU General  Public License as published by the
- *  Free Software Foundation;  either version 2 of the  License, or (at your
- *  option) any later version.
- *
- *  THIS  SOFTWARE  IS PROVIDED   ``AS  IS'' AND   ANY  EXPRESS OR IMPLIED
- *  WARRANTIES,   INCLUDING, BUT NOT  LIMITED  TO, THE IMPLIED WARRANTIES OF
- *  MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.  IN
- *  NO  EVENT  SHALL   THE AUTHOR  BE    LIABLE FOR ANY   DIRECT, INDIRECT,
- *  INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
- *  NOT LIMITED   TO, PROCUREMENT OF  SUBSTITUTE GOODS  OR SERVICES; LOSS OF
- *  USE, DATA,  OR PROFITS; OR  BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
- *  ANY THEORY OF LIABILITY, WHETHER IN  CONTRACT, STRICT LIABILITY, OR TORT
- *  (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
- *  THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- *  You should have received a copy of the  GNU General Public License along
- *  with this program; if not, write  to the Free Software Foundation, Inc.,
- *  675 Mass Ave, Cambridge, MA 02139, USA.
- *
- * Copyright 2004 Ralf Baechle <ralf@linux-mips.org>
- */
-#include <asm/sn/addrs.h>
-#include <asm/sn/sn0/hub.h>
-#include <asm/sn/klconfig.h>
-#include <asm/sn/ioc3.h>
-#include <asm/sn/sn_private.h>
-
-#include <linux/serial.h>
-#include <linux/serial_core.h>
-#include <linux/serial_reg.h>
-
-#define IOC3_CLK        (22000000 / 3)
-#define IOC3_FLAGS      (0)
-
-static inline struct ioc3_uartregs *console_uart(void)
-{
-	struct ioc3 *ioc3;
-
-	ioc3 = (struct ioc3 *)KL_CONFIG_CH_CONS_INFO(get_nasid())->memory_base;
-
-	return &ioc3->sregs.uarta;
-}
-
-unsigned char getDebugChar(void)
-{
-	struct ioc3_uartregs *uart = console_uart();
-
-	while ((uart->iu_lsr & UART_LSR_DR) == 0);
-	return uart->iu_rbr;
-}
-
-void putDebugChar(unsigned char c)
-{
-	struct ioc3_uartregs *uart = console_uart();
-
-	while ((uart->iu_lsr & UART_LSR_THRE) == 0);
-	uart->iu_thr = c;
-}

arch/mips/sibyte/bcm1480/irq.c

@@ -57,30 +57,6 @@ static void bcm1480_set_affinity(unsigned int irq, cpumask_t mask);
 extern unsigned long ht_eoi_space;
 #endif
 
-#ifdef CONFIG_KGDB
-#include <asm/gdb-stub.h>
-extern void breakpoint(void);
-static int kgdb_irq;
-#ifdef CONFIG_GDB_CONSOLE
-extern void register_gdb_console(void);
-#endif
-
-/* kgdb is on when configured.  Pass "nokgdb" kernel arg to turn it off */
-static int kgdb_flag = 1;
-static int __init nokgdb(char *str)
-{
-	kgdb_flag = 0;
-	return 1;
-}
-__setup("nokgdb", nokgdb);
-
-/* Default to UART1 */
-int kgdb_port = 1;
-#ifdef CONFIG_SERIAL_SB1250_DUART
-extern char sb1250_duart_present[];
-#endif
-#endif
-
 static struct irq_chip bcm1480_irq_type = {
 	.name = "BCM1480-IMR",
 	.ack = ack_bcm1480_irq,
@@ -355,61 +331,10 @@ void __init arch_init_irq(void)
 	 * does its own management of IP7.
 	 */
 
-#ifdef CONFIG_KGDB
-	imask |= STATUSF_IP6;
-#endif
 	/* Enable necessary IPs, disable the rest */
 	change_c0_status(ST0_IM, imask);
-
-#ifdef CONFIG_KGDB
-	if (kgdb_flag) {
-		kgdb_irq = K_BCM1480_INT_UART_0 + kgdb_port;
-
-#ifdef CONFIG_SERIAL_SB1250_DUART
-		sb1250_duart_present[kgdb_port] = 0;
-#endif
-		/* Setup uart 1 settings, mapper */
-		/* QQQ FIXME */
-		__raw_writeq(M_DUART_IMR_BRK, IOADDR(A_DUART_IMRREG(kgdb_port)));
-
-		__raw_writeq(IMR_IP6_VAL,
-			     IOADDR(A_BCM1480_IMR_REGISTER(0, R_BCM1480_IMR_INTERRUPT_MAP_BASE_H) +
-			     (kgdb_irq << 3)));
-		bcm1480_unmask_irq(0, kgdb_irq);
-
-#ifdef CONFIG_GDB_CONSOLE
-		register_gdb_console();
-#endif
-		printk("Waiting for GDB on UART port %d\n", kgdb_port);
-		set_debug_traps();
-		breakpoint();
-	}
-#endif
-}
-
-#ifdef CONFIG_KGDB
-
-#include <linux/delay.h>
-
-#define duart_out(reg, val)     csr_out32(val, IOADDR(A_DUART_CHANREG(kgdb_port, reg)))
-#define duart_in(reg)           csr_in32(IOADDR(A_DUART_CHANREG(kgdb_port, reg)))
-
-static void bcm1480_kgdb_interrupt(void)
-{
-	/*
-	 * Clear break-change status (allow some time for the remote
-	 * host to stop the break, since we would see another
-	 * interrupt on the end-of-break too)
-	 */
-	kstat.irqs[smp_processor_id()][kgdb_irq]++;
-	mdelay(500);
-	duart_out(R_DUART_CMD, V_DUART_MISC_CMD_RESET_BREAK_INT |
-				M_DUART_RX_EN | M_DUART_TX_EN);
-	set_async_breakpoint(&get_irq_regs()->cp0_epc);
 }
 
-#endif 	/* CONFIG_KGDB */
-
 extern void bcm1480_mailbox_interrupt(void);
 
 static inline void dispatch_ip2(void)
@@ -462,11 +387,6 @@ asmlinkage void plat_irq_dispatch(void)
 		bcm1480_mailbox_interrupt();
 #endif
 
-#ifdef CONFIG_KGDB
-	else if (pending & CAUSEF_IP6)
-		bcm1480_kgdb_interrupt();		/* KGDB (uart 1) */
-#endif
-
 	else if (pending & CAUSEF_IP2)
 		dispatch_ip2();
 }

arch/mips/sibyte/cfe/setup.c

@@ -59,10 +59,6 @@ int cfe_cons_handle;
 extern unsigned long initrd_start, initrd_end;
 #endif
 
-#ifdef CONFIG_KGDB
-extern int kgdb_port;
-#endif
-
 static void __noreturn cfe_linux_exit(void *arg)
 {
 	int warm = *(int *)arg;
@@ -246,9 +242,6 @@ void __init prom_init(void)
 	int argc = fw_arg0;
 	char **envp = (char **) fw_arg2;
 	int *prom_vec = (int *) fw_arg3;
-#ifdef CONFIG_KGDB
-	char *arg;
-#endif
 
 	_machine_restart   = cfe_linux_restart;
 	_machine_halt      = cfe_linux_halt;
@@ -309,13 +302,6 @@ void __init prom_init(void)
 		}
 	}
 
-#ifdef CONFIG_KGDB
-	if ((arg = strstr(arcs_cmdline, "kgdb=duart")) != NULL)
-		kgdb_port = (arg[10] == '0') ? 0 : 1;
-	else
-		kgdb_port = 1;
-#endif
-
 #ifdef CONFIG_BLK_DEV_INITRD
 	{
 		char *ptr;

arch/mips/sibyte/sb1250/irq.c

@@ -57,16 +57,6 @@ static void sb1250_set_affinity(unsigned int irq, cpumask_t mask);
 extern unsigned long ldt_eoi_space;
 #endif
 
-#ifdef CONFIG_KGDB
-static int kgdb_irq;
-
-/* Default to UART1 */
-int kgdb_port = 1;
-#ifdef CONFIG_SERIAL_SB1250_DUART
-extern char sb1250_duart_present[];
-#endif
-#endif
-
 static struct irq_chip sb1250_irq_type = {
 	.name = "SB1250-IMR",
 	.ack = ack_sb1250_irq,
@@ -313,55 +303,10 @@ void __init arch_init_irq(void)
 	 * does its own management of IP7.
 	 */
 
-#ifdef CONFIG_KGDB
-	imask |= STATUSF_IP6;
-#endif
 	/* Enable necessary IPs, disable the rest */
 	change_c0_status(ST0_IM, imask);
-
-#ifdef CONFIG_KGDB
-	if (kgdb_flag) {
-		kgdb_irq = K_INT_UART_0 + kgdb_port;
-
-#ifdef CONFIG_SERIAL_SB1250_DUART
-		sb1250_duart_present[kgdb_port] = 0;
-#endif
-		/* Setup uart 1 settings, mapper */
-		__raw_writeq(M_DUART_IMR_BRK,
-			     IOADDR(A_DUART_IMRREG(kgdb_port)));
-
-		__raw_writeq(IMR_IP6_VAL,
-			     IOADDR(A_IMR_REGISTER(0,
-						   R_IMR_INTERRUPT_MAP_BASE) +
-				    (kgdb_irq << 3)));
-		sb1250_unmask_irq(0, kgdb_irq);
-	}
-#endif
-}
-
-#ifdef CONFIG_KGDB
-
-#include <linux/delay.h>
-
-#define duart_out(reg, val)     csr_out32(val, IOADDR(A_DUART_CHANREG(kgdb_port, reg)))
-#define duart_in(reg)           csr_in32(IOADDR(A_DUART_CHANREG(kgdb_port, reg)))
-
-static void sb1250_kgdb_interrupt(void)
-{
-	/*
-	 * Clear break-change status (allow some time for the remote
-	 * host to stop the break, since we would see another
-	 * interrupt on the end-of-break too)
-	 */
-	kstat_this_cpu.irqs[kgdb_irq]++;
-	mdelay(500);
-	duart_out(R_DUART_CMD, V_DUART_MISC_CMD_RESET_BREAK_INT |
-				M_DUART_RX_EN | M_DUART_TX_EN);
-	set_async_breakpoint(&get_irq_regs()->cp0_epc);
 }
 
-#endif 	/* CONFIG_KGDB */
-
 extern void sb1250_mailbox_interrupt(void);
 
 static inline void dispatch_ip2(void)
@@ -407,11 +352,6 @@ asmlinkage void plat_irq_dispatch(void)
 		sb1250_mailbox_interrupt();
 #endif
 
-#ifdef CONFIG_KGDB
-	else if (pending & CAUSEF_IP6)			/* KGDB (uart 1) */
-		sb1250_kgdb_interrupt();
-#endif
-
 	else if (pending & CAUSEF_IP2)
 		dispatch_ip2();
 	else

arch/mips/sibyte/swarm/Makefile

 obj-y				:= setup.o rtc_xicor1241.o rtc_m41t81.o
 
 obj-$(CONFIG_I2C_BOARDINFO)	+= swarm-i2c.o
-obj-$(CONFIG_KGDB)		+= dbg_io.o

arch/mips/sibyte/swarm/dbg_io.c

-/*
- * kgdb debug routines for SiByte boards.
- *
- * Copyright (C) 2001 MontaVista Software Inc.
- * Author: Jun Sun, jsun@mvista.com or jsun@junsun.net
- *
- * This program is free software; you can redistribute  it and/or modify it
- * under  the terms of  the GNU General  Public License as published by the
- * Free Software Foundation;  either version 2 of the  License, or (at your
- * option) any later version.
- *
- */
-
-/* -------------------- BEGINNING OF CONFIG --------------------- */
-
-#include <linux/delay.h>
-#include <asm/io.h>
-#include <asm/sibyte/sb1250.h>
-#include <asm/sibyte/sb1250_regs.h>
-#include <asm/sibyte/sb1250_uart.h>
-#include <asm/sibyte/sb1250_int.h>
-#include <asm/addrspace.h>
-
-/*
- * We use the second serial port for kgdb traffic.
- * 	115200, 8, N, 1.
- */
-
-#define	BAUD_RATE		115200
-#define	CLK_DIVISOR		V_DUART_BAUD_RATE(BAUD_RATE)
-#define	DATA_BITS		V_DUART_BITS_PER_CHAR_8		/* or 7    */
-#define	PARITY			V_DUART_PARITY_MODE_NONE	/* or even */
-#define	STOP_BITS		M_DUART_STOP_BIT_LEN_1		/* or 2    */
-
-static int duart_initialized = 0;	/* 0: need to be init'ed by kgdb */
-
-/* -------------------- END OF CONFIG --------------------- */
-extern int kgdb_port;
-
-#define	duart_out(reg, val)	csr_out32(val, IOADDR(A_DUART_CHANREG(kgdb_port, reg)))
-#define duart_in(reg)		csr_in32(IOADDR(A_DUART_CHANREG(kgdb_port, reg)))
-
-void putDebugChar(unsigned char c);
-unsigned char getDebugChar(void);
-static void
-duart_init(int clk_divisor, int data, int parity, int stop)
-{
-	duart_out(R_DUART_MODE_REG_1, data | parity);
-	duart_out(R_DUART_MODE_REG_2, stop);
-	duart_out(R_DUART_CLK_SEL, clk_divisor);
-
-	duart_out(R_DUART_CMD, M_DUART_RX_EN | M_DUART_TX_EN);	/* enable rx and tx */
-}
-
-void
-putDebugChar(unsigned char c)
-{
-	if (!duart_initialized) {
-		duart_initialized = 1;
-		duart_init(CLK_DIVISOR, DATA_BITS, PARITY, STOP_BITS);
-	}
-	while ((duart_in(R_DUART_STATUS) & M_DUART_TX_RDY) == 0);
-	duart_out(R_DUART_TX_HOLD, c);
-}
-
-unsigned char
-getDebugChar(void)
-{
-	if (!duart_initialized) {
-		duart_initialized = 1;
-		duart_init(CLK_DIVISOR, DATA_BITS, PARITY, STOP_BITS);
-	}
-	while ((duart_in(R_DUART_STATUS) & M_DUART_RX_RDY) == 0) ;
-	return duart_in(R_DUART_RX_HOLD);
-}
-

arch/mips/txx9/Kconfig

+config MACH_TX39XX
+	bool
+	select MACH_TXX9
+	select SYS_HAS_CPU_TX39XX
+
+config MACH_TX49XX
+	bool
+	select MACH_TXX9
+	select CEVT_R4K
+	select CSRC_R4K
+	select IRQ_CPU
+	select SYS_HAS_CPU_TX49XX
+	select SYS_SUPPORTS_64BIT_KERNEL
+
+config MACH_TXX9
+	bool
+	select DMA_NONCOHERENT
+	select SWAP_IO_SPACE
+	select SYS_HAS_EARLY_PRINTK
+	select SYS_SUPPORTS_32BIT_KERNEL
+	select SYS_SUPPORTS_LITTLE_ENDIAN
+	select SYS_SUPPORTS_BIG_ENDIAN
+	select GENERIC_HARDIRQS_NO__DO_IRQ
+
 config TOSHIBA_JMR3927
 	bool "Toshiba JMR-TX3927 board"
 	depends on MACH_TX39XX
@@ -24,68 +48,37 @@ config TOSHIBA_RBTX4938
 config SOC_TX3927
 	bool
 	select CEVT_TXX9
-	select DMA_NONCOHERENT
 	select HAS_TXX9_SERIAL
 	select HW_HAS_PCI
 	select IRQ_TXX9
-	select SWAP_IO_SPACE
-	select SYS_HAS_CPU_TX39XX
-	select SYS_SUPPORTS_32BIT_KERNEL
-	select SYS_SUPPORTS_LITTLE_ENDIAN
-	select SYS_SUPPORTS_BIG_ENDIAN
-	select GENERIC_HARDIRQS_NO__DO_IRQ
 	select GPIO_TXX9
 
 config SOC_TX4927
 	bool
-	select CEVT_R4K
-	select CSRC_R4K
 	select CEVT_TXX9
-	select DMA_NONCOHERENT
 	select HAS_TXX9_SERIAL
 	select HW_HAS_PCI
-	select IRQ_CPU
 	select IRQ_TXX9
 	select PCI_TX4927
-	select SWAP_IO_SPACE
-	select SYS_HAS_CPU_TX49XX
-	select SYS_SUPPORTS_32BIT_KERNEL
-	select SYS_SUPPORTS_64BIT_KERNEL
-	select SYS_SUPPORTS_LITTLE_ENDIAN
-	select SYS_SUPPORTS_BIG_ENDIAN
-	select SYS_SUPPORTS_KGDB
-	select GENERIC_HARDIRQS_NO__DO_IRQ
 	select GPIO_TXX9
 
 config SOC_TX4938
 	bool
-	select CEVT_R4K
-	select CSRC_R4K
 	select CEVT_TXX9
-	select DMA_NONCOHERENT
 	select HAS_TXX9_SERIAL
 	select HW_HAS_PCI
-	select IRQ_CPU
 	select IRQ_TXX9
 	select PCI_TX4927
-	select SWAP_IO_SPACE
-	select SYS_HAS_CPU_TX49XX
-	select SYS_SUPPORTS_32BIT_KERNEL
-	select SYS_SUPPORTS_64BIT_KERNEL
-	select SYS_SUPPORTS_LITTLE_ENDIAN
-	select SYS_SUPPORTS_BIG_ENDIAN
-	select SYS_SUPPORTS_KGDB
-	select GENERIC_HARDIRQS_NO__DO_IRQ
 	select GPIO_TXX9
 
 config TOSHIBA_FPCIB0
 	bool "FPCIB0 Backplane Support"
-	depends on PCI && (MACH_TX39XX || MACH_TX49XX)
+	depends on PCI && MACH_TXX9
 	select I8259
 
 config PICMG_PCI_BACKPLANE_DEFAULT
 	bool "Support for PICMG PCI Backplane"
-	depends on PCI && (MACH_TX39XX || MACH_TX49XX)
+	depends on PCI && MACH_TXX9
 	default y if !TOSHIBA_FPCIB0
 
 if TOSHIBA_RBTX4938

arch/mips/txx9/generic/Makefile

@@ -4,9 +4,9 @@
 
 obj-y	+= setup.o
 obj-$(CONFIG_PCI)	+= pci.o
+obj-$(CONFIG_SOC_TX3927)	+= setup_tx3927.o irq_tx3927.o
 obj-$(CONFIG_SOC_TX4927)	+= mem_tx4927.o setup_tx4927.o irq_tx4927.o
 obj-$(CONFIG_SOC_TX4938)	+= mem_tx4927.o setup_tx4938.o irq_tx4938.o
 obj-$(CONFIG_TOSHIBA_FPCIB0)	+= smsc_fdc37m81x.o
-obj-$(CONFIG_KGDB)	+= dbgio.o
 
 EXTRA_CFLAGS += -Werror

arch/mips/txx9/generic/dbgio.c

-/*
- * linux/arch/mips/tx4938/common/dbgio.c
- *
- * kgdb interface for gdb
- *
- * Author: MontaVista Software, Inc.
- *         source@mvista.com
- *
- * Copyright 2005 MontaVista Software Inc.
- *
- *  This program is free software; you can redistribute it and/or modify it
- *  under the terms of the GNU General Public License as published by the
- *  Free Software Foundation; either version 2 of the License, or (at your
- *  option) any later version.
- *
- *  THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
- *  WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
- *  MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
- *  IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
- *  INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
- *  BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
- *  OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
- *  ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR
- *  TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE
- *  USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- *  You should have received a copy of the GNU General Public License along
- *  with this program; if not, write to the Free Software Foundation, Inc.,
- *  675 Mass Ave, Cambridge, MA 02139, USA.
- *
- * Support for TX4938 in 2.6 - Hiroshi DOYU <Hiroshi_DOYU@montavista.co.jp>
- */
-
-#include <linux/types>
-
-extern u8 txx9_sio_kdbg_rd(void);
-extern int txx9_sio_kdbg_wr( u8 ch );
-
-u8 getDebugChar(void)
-{
-	return (txx9_sio_kdbg_rd());
-}
-
-int putDebugChar(u8 byte)
-{
-	return (txx9_sio_kdbg_wr(byte));
-}
-

arch/mips/txx9/generic/irq_tx3927.c

+/*
+ * Common tx3927 irq handler
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright 2001 MontaVista Software Inc.
+ * Copyright (C) 2000-2001 Toshiba Corporation
+ */
+#include <linux/init.h>
+#include <asm/txx9irq.h>
+#include <asm/txx9/tx3927.h>
+
+void __init tx3927_irq_init(void)
+{
+	int i;
+
+	txx9_irq_init(TX3927_IRC_REG);
+	/* raise priority for timers, sio */
+	for (i = 0; i < TX3927_NR_TMR; i++)
+		txx9_irq_set_pri(TX3927_IR_TMR(i), 6);
+	for (i = 0; i < TX3927_NR_SIO; i++)
+		txx9_irq_set_pri(TX3927_IR_SIO(i), 7);
+}

arch/mips/txx9/generic/pci.c

@@ -386,3 +386,39 @@ int __init pcibios_map_irq(const struct pci_dev *dev, u8 slot, u8 pin)
 {
 	return txx9_board_vec->pci_map_irq(dev, slot, pin);
 }
+
+char * (*txx9_board_pcibios_setup)(char *str) __devinitdata;
+
+char *__devinit txx9_pcibios_setup(char *str)
+{
+	if (txx9_board_pcibios_setup && !txx9_board_pcibios_setup(str))
+		return NULL;
+	if (!strcmp(str, "picmg")) {
+		/* PICMG compliant backplane (TOSHIBA JMB-PICMG-ATX
+		   (5V or 3.3V), JMB-PICMG-L2 (5V only), etc.) */
+		txx9_pci_option |= TXX9_PCI_OPT_PICMG;
+		return NULL;
+	} else if (!strcmp(str, "nopicmg")) {
+		/* non-PICMG compliant backplane (TOSHIBA
+		   RBHBK4100,RBHBK4200, Interface PCM-PCM05, etc.) */
+		txx9_pci_option &= ~TXX9_PCI_OPT_PICMG;
+		return NULL;
+	} else if (!strncmp(str, "clk=", 4)) {
+		char *val = str + 4;
+		txx9_pci_option &= ~TXX9_PCI_OPT_CLK_MASK;
+		if (strcmp(val, "33") == 0)
+			txx9_pci_option |= TXX9_PCI_OPT_CLK_33;
+		else if (strcmp(val, "66") == 0)
+			txx9_pci_option |= TXX9_PCI_OPT_CLK_66;
+		else /* "auto" */
+			txx9_pci_option |= TXX9_PCI_OPT_CLK_AUTO;
+		return NULL;
+	} else if (!strncmp(str, "err=", 4)) {
+		if (!strcmp(str + 4, "panic"))
+			txx9_pci_err_action = TXX9_PCI_ERR_PANIC;
+		else if (!strcmp(str + 4, "ignore"))
+			txx9_pci_err_action = TXX9_PCI_ERR_IGNORE;
+		return NULL;
+	}
+	return str;
+}

arch/mips/txx9/jmr3927/Makefile

@@ -3,6 +3,5 @@
 #
 
 obj-y	+= prom.o irq.o setup.o
-obj-$(CONFIG_KGDB)	+= kgdb_io.o
 
 EXTRA_CFLAGS += -Werror

arch/mips/txx9/rbtx4927/prom.c

@@ -38,4 +38,5 @@ void __init rbtx4927_prom_init(void)
 {
 	prom_init_cmdline();
 	add_memory_region(0, tx4927_get_mem_size(), BOOT_MEM_RAM);
+	txx9_sio_putchar_init(TX4927_SIO_REG(0) & 0xfffffffffULL);
 }

arch/mips/txx9/rbtx4938/prom.c

@@ -22,4 +22,5 @@ void __init rbtx4938_prom_init(void)
 	prom_init_cmdline();
 #endif
 	add_memory_region(0, tx4938_get_mem_size(), BOOT_MEM_RAM);
+	txx9_sio_putchar_init(TX4938_SIO_REG(0) & 0xfffffffffULL);
 }