Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-next

drivers/net/ethernet/intel/e1000e/netdev.c

@@ -6238,7 +6238,8 @@ static int __devinit e1000_probe(struct pci_dev *pdev,
 	}
 
 	if (hw->phy.ops.check_reset_block && hw->phy.ops.check_reset_block(hw))
-		e_info("PHY reset is blocked due to SOL/IDER session.\n");
+		dev_info(&pdev->dev,
+			 "PHY reset is blocked due to SOL/IDER session.\n");
 
 	/* Set initial default active device features */
 	netdev->features = (NETIF_F_SG |
@@ -6288,7 +6289,7 @@ static int __devinit e1000_probe(struct pci_dev *pdev,
 		if (e1000_validate_nvm_checksum(&adapter->hw) >= 0)
 			break;
 		if (i == 2) {
-			e_err("The NVM Checksum Is Not Valid\n");
+			dev_err(&pdev->dev, "The NVM Checksum Is Not Valid\n");
 			err = -EIO;
 			goto err_eeprom;
 		}
@@ -6298,13 +6299,15 @@ static int __devinit e1000_probe(struct pci_dev *pdev,
 
 	/* copy the MAC address */
 	if (e1000e_read_mac_addr(&adapter->hw))
-		e_err("NVM Read Error while reading MAC address\n");
+		dev_err(&pdev->dev,
+			"NVM Read Error while reading MAC address\n");
 
 	memcpy(netdev->dev_addr, adapter->hw.mac.addr, netdev->addr_len);
 	memcpy(netdev->perm_addr, adapter->hw.mac.addr, netdev->addr_len);
 
 	if (!is_valid_ether_addr(netdev->perm_addr)) {
-		e_err("Invalid MAC Address: %pM\n", netdev->perm_addr);
+		dev_err(&pdev->dev, "Invalid MAC Address: %pM\n",
+			netdev->perm_addr);
 		err = -EIO;
 		goto err_eeprom;
 	}

drivers/net/ethernet/intel/e1000e/param.c

@@ -199,16 +199,19 @@ static int __devinit e1000_validate_option(unsigned int *value,
 	case enable_option:
 		switch (*value) {
 		case OPTION_ENABLED:
-			e_info("%s Enabled\n", opt->name);
+			dev_info(&adapter->pdev->dev, "%s Enabled\n",
+				 opt->name);
 			return 0;
 		case OPTION_DISABLED:
-			e_info("%s Disabled\n", opt->name);
+			dev_info(&adapter->pdev->dev, "%s Disabled\n",
+				 opt->name);
 			return 0;
 		}
 		break;
 	case range_option:
 		if (*value >= opt->arg.r.min && *value <= opt->arg.r.max) {
-			e_info("%s set to %i\n", opt->name, *value);
+			dev_info(&adapter->pdev->dev, "%s set to %i\n",
+				 opt->name, *value);
 			return 0;
 		}
 		break;
@@ -220,7 +223,8 @@ static int __devinit e1000_validate_option(unsigned int *value,
 			ent = &opt->arg.l.p[i];
 			if (*value == ent->i) {
 				if (ent->str[0] != '\0')
-					e_info("%s\n", ent->str);
+					dev_info(&adapter->pdev->dev, "%s\n",
+						 ent->str);
 				return 0;
 			}
 		}
@@ -230,8 +234,8 @@ static int __devinit e1000_validate_option(unsigned int *value,
 		BUG();
 	}
 
-	e_info("Invalid %s value specified (%i) %s\n", opt->name, *value,
-	       opt->err);
+	dev_info(&adapter->pdev->dev, "Invalid %s value specified (%i) %s\n",
+		 opt->name, *value, opt->err);
 	*value = opt->def;
 	return -1;
 }
@@ -251,8 +255,10 @@ void __devinit e1000e_check_options(struct e1000_adapter *adapter)
 	int bd = adapter->bd_number;
 
 	if (bd >= E1000_MAX_NIC) {
-		e_notice("Warning: no configuration for board #%i\n", bd);
-		e_notice("Using defaults for all values\n");
+		dev_notice(&adapter->pdev->dev,
+			   "Warning: no configuration for board #%i\n", bd);
+		dev_notice(&adapter->pdev->dev,
+			   "Using defaults for all values\n");
 	}
 
 	{ /* Transmit Interrupt Delay */
@@ -366,26 +372,31 @@ void __devinit e1000e_check_options(struct e1000_adapter *adapter)
 			 * default values
 			 */
 			if (adapter->itr > 4)
-				e_info("%s set to default %d\n", opt.name,
+				dev_info(&adapter->pdev->dev,
+					 "%s set to default %d\n", opt.name,
 					 adapter->itr);
 		}
 
 		adapter->itr_setting = adapter->itr;
 		switch (adapter->itr) {
 		case 0:
-			e_info("%s turned off\n", opt.name);
+			dev_info(&adapter->pdev->dev, "%s turned off\n",
+				 opt.name);
 			break;
 		case 1:
-			e_info("%s set to dynamic mode\n", opt.name);
+			dev_info(&adapter->pdev->dev,
+				 "%s set to dynamic mode\n", opt.name);
 			adapter->itr = 20000;
 			break;
 		case 3:
-			e_info("%s set to dynamic conservative mode\n",
+			dev_info(&adapter->pdev->dev,
+				 "%s set to dynamic conservative mode\n",
 				 opt.name);
 			adapter->itr = 20000;
 			break;
 		case 4:
-			e_info("%s set to simplified (2000-8000 ints) mode\n",
+			dev_info(&adapter->pdev->dev,
+				 "%s set to simplified (2000-8000 ints) mode\n",
 				 opt.name);
 			break;
 		default:

drivers/net/ethernet/intel/ixgbe/Makefile

@@ -34,11 +34,11 @@ obj-$(CONFIG_IXGBE) += ixgbe.o
 
 ixgbe-objs := ixgbe_main.o ixgbe_common.o ixgbe_ethtool.o \
               ixgbe_82599.o ixgbe_82598.o ixgbe_phy.o ixgbe_sriov.o \
-              ixgbe_mbx.o ixgbe_x540.o ixgbe_sysfs.o ixgbe_lib.o
+              ixgbe_mbx.o ixgbe_x540.o ixgbe_lib.o
 
 ixgbe-$(CONFIG_IXGBE_DCB) +=  ixgbe_dcb.o ixgbe_dcb_82598.o \
                               ixgbe_dcb_82599.o ixgbe_dcb_nl.o
 
 ixgbe-$(CONFIG_IXGBE_PTP) += ixgbe_ptp.o
-
+ixgbe-$(CONFIG_IXGBE_HWMON) += ixgbe_sysfs.o
 ixgbe-$(CONFIG_FCOE:m=y) += ixgbe_fcoe.o

drivers/net/ethernet/intel/ixgbe/ixgbe.h

@@ -561,6 +561,7 @@ struct ixgbe_adapter {
 	spinlock_t tmreg_lock;
 	struct cyclecounter cc;
 	struct timecounter tc;
+	int rx_hwtstamp_filter;
 	u32 base_incval;
 	u32 cycle_speed;
 #endif /* CONFIG_IXGBE_PTP */
@@ -718,6 +719,7 @@ extern void ixgbe_ptp_overflow_check(struct ixgbe_adapter *adapter);
 extern void ixgbe_ptp_tx_hwtstamp(struct ixgbe_q_vector *q_vector,
 				  struct sk_buff *skb);
 extern void ixgbe_ptp_rx_hwtstamp(struct ixgbe_q_vector *q_vector,
+				  union ixgbe_adv_rx_desc *rx_desc,
 				  struct sk_buff *skb);
 extern int ixgbe_ptp_hwtstamp_ioctl(struct ixgbe_adapter *adapter,
 				    struct ifreq *ifr, int cmd);

drivers/net/ethernet/intel/ixgbe/ixgbe_main.c

@@ -790,12 +790,10 @@ static bool ixgbe_clean_tx_irq(struct ixgbe_q_vector *q_vector,
 		total_packets += tx_buffer->gso_segs;
 
 #ifdef CONFIG_IXGBE_PTP
-		if (unlikely(tx_buffer->tx_flags &
-			     IXGBE_TX_FLAGS_TSTAMP))
-			ixgbe_ptp_tx_hwtstamp(q_vector,
-					      tx_buffer->skb);
-
+		if (unlikely(tx_buffer->tx_flags & IXGBE_TX_FLAGS_TSTAMP))
+			ixgbe_ptp_tx_hwtstamp(q_vector, tx_buffer->skb);
 #endif
+
 		/* free the skb */
 		dev_kfree_skb_any(tx_buffer->skb);
 
@@ -1399,8 +1397,7 @@ static void ixgbe_process_skb_fields(struct ixgbe_ring *rx_ring,
 	ixgbe_rx_checksum(rx_ring, rx_desc, skb);
 
 #ifdef CONFIG_IXGBE_PTP
-	if (ixgbe_test_staterr(rx_desc, IXGBE_RXDADV_STAT_TS))
-		ixgbe_ptp_rx_hwtstamp(rx_ring->q_vector, skb);
+	ixgbe_ptp_rx_hwtstamp(rx_ring->q_vector, rx_desc, skb);
 #endif
 
 	if ((dev->features & NETIF_F_HW_VLAN_RX) &&

drivers/net/ethernet/intel/ixgbe/ixgbe_ptp.c

@@ -26,6 +26,7 @@
 *******************************************************************************/
 #include "ixgbe.h"
 #include <linux/export.h>
+#include <linux/ptp_classify.h>
 
 /*
  * The 82599 and the X540 do not have true 64bit nanosecond scale
@@ -100,6 +101,10 @@
 #define NSECS_PER_SEC 1000000000ULL
 #endif
 
+static struct sock_filter ptp_filter[] = {
+	PTP_FILTER
+};
+
 /**
  * ixgbe_ptp_read - read raw cycle counter (to be used by time counter)
  * @cc - the cyclecounter structure
@@ -307,14 +312,15 @@ void ixgbe_ptp_check_pps_event(struct ixgbe_adapter *adapter, u32 eicr)
 	    !(adapter->flags2 & IXGBE_FLAG2_PTP_PPS_ENABLED))
 		return;
 
+	if (unlikely(eicr & IXGBE_EICR_TIMESYNC)) {
 		switch (hw->mac.type) {
 		case ixgbe_mac_X540:
-		if (eicr & IXGBE_EICR_TIMESYNC)
 			ptp_clock_event(adapter->ptp_clock, &event);
 			break;
 		default:
 			break;
 		}
+	}
 }
 
 /**
@@ -424,6 +430,68 @@ void ixgbe_ptp_overflow_check(struct ixgbe_adapter *adapter)
 	}
 }
 
+/**
+ * ixgbe_ptp_match - determine if this skb matches a ptp packet
+ * @skb: pointer to the skb
+ * @hwtstamp: pointer to the hwtstamp_config to check
+ *
+ * Determine whether the skb should have been timestamped, assuming the
+ * hwtstamp was set via the hwtstamp ioctl. Returns non-zero when the packet
+ * should have a timestamp waiting in the registers, and 0 otherwise.
+ *
+ * V1 packets have to check the version type to determine whether they are
+ * correct. However, we can't directly access the data because it might be
+ * fragmented in the SKB, in paged memory. In order to work around this, we
+ * use skb_copy_bits which will properly copy the data whether it is in the
+ * paged memory fragments or not. We have to copy the IP header as well as the
+ * message type.
+ */
+static int ixgbe_ptp_match(struct sk_buff *skb, int rx_filter)
+{
+	struct iphdr iph;
+	u8 msgtype;
+	unsigned int type, offset;
+
+	if (rx_filter == HWTSTAMP_FILTER_NONE)
+		return 0;
+
+	type = sk_run_filter(skb, ptp_filter);
+
+	if (likely(rx_filter == HWTSTAMP_FILTER_PTP_V2_EVENT))
+		return type & PTP_CLASS_V2;
+
+	/* For the remaining cases actually check message type */
+	switch (type) {
+	case PTP_CLASS_V1_IPV4:
+		skb_copy_bits(skb, OFF_IHL, &iph, sizeof(iph));
+		offset = ETH_HLEN + (iph.ihl << 2) + UDP_HLEN + OFF_PTP_CONTROL;
+		break;
+	case PTP_CLASS_V1_IPV6:
+		offset = OFF_PTP6 + OFF_PTP_CONTROL;
+		break;
+	default:
+		/* other cases invalid or handled above */
+		return 0;
+	}
+
+	/* Make sure our buffer is long enough */
+	if (skb->len < offset)
+		return 0;
+
+	skb_copy_bits(skb, offset, &msgtype, sizeof(msgtype));
+
+	switch (rx_filter) {
+	case HWTSTAMP_FILTER_PTP_V1_L4_SYNC:
+		return (msgtype == IXGBE_RXMTRL_V1_SYNC_MSG);
+		break;
+	case HWTSTAMP_FILTER_PTP_V1_L4_DELAY_REQ:
+		return (msgtype == IXGBE_RXMTRL_V1_DELAY_REQ_MSG);
+		break;
+	default:
+		return 0;
+	}
+}
+
 /**
  * ixgbe_ptp_tx_hwtstamp - utility function which checks for TX time stamp
  * @q_vector: structure containing interrupt and ring information
@@ -473,6 +541,7 @@ void ixgbe_ptp_tx_hwtstamp(struct ixgbe_q_vector *q_vector,
 /**
  * ixgbe_ptp_rx_hwtstamp - utility function which checks for RX time stamp
  * @q_vector: structure containing interrupt and ring information
+ * @rx_desc: the rx descriptor
  * @skb: particular skb to send timestamp with
  *
  * if the timestamp is valid, we convert it into the timecounter ns
@@ -480,6 +549,7 @@ void ixgbe_ptp_tx_hwtstamp(struct ixgbe_q_vector *q_vector,
  * is passed up the network stack
  */
 void ixgbe_ptp_rx_hwtstamp(struct ixgbe_q_vector *q_vector,
+			   union ixgbe_adv_rx_desc *rx_desc,
 			   struct sk_buff *skb)
 {
 	struct ixgbe_adapter *adapter;
@@ -497,21 +567,33 @@ void ixgbe_ptp_rx_hwtstamp(struct ixgbe_q_vector *q_vector,
 	hw = &adapter->hw;
 
 	tsyncrxctl = IXGBE_READ_REG(hw, IXGBE_TSYNCRXCTL);
+
+	/* Check if we have a valid timestamp and make sure the skb should
+	 * have been timestamped */
+	if (likely(!(tsyncrxctl & IXGBE_TSYNCRXCTL_VALID) ||
+		   !ixgbe_ptp_match(skb, adapter->rx_hwtstamp_filter)))
+		return;
+
+	/*
+	 * Always read the registers, in order to clear a possible fault
+	 * because of stagnant RX timestamp values for a packet that never
+	 * reached the queue.
+	 */
 	regval |= (u64)IXGBE_READ_REG(hw, IXGBE_RXSTMPL);
 	regval |= (u64)IXGBE_READ_REG(hw, IXGBE_RXSTMPH) << 32;
 
 	/*
-	 * If this bit is set, then the RX registers contain the time stamp. No
-	 * other packet will be time stamped until we read these registers, so
-	 * read the registers to make them available again. Because only one
-	 * packet can be time stamped at a time, we know that the register
-	 * values must belong to this one here and therefore we don't need to
-	 * compare any of the additional attributes stored for it.
+	 * If the timestamp bit is set in the packet's descriptor, we know the
+	 * timestamp belongs to this packet. No other packet can be
+	 * timestamped until the registers for timestamping have been read.
+	 * Therefor only one packet with this bit can be in the queue at a
+	 * time, and the rx timestamp values that were in the registers belong
+	 * to this packet.
 	 *
 	 * If nothing went wrong, then it should have a skb_shared_tx that we
 	 * can turn into a skb_shared_hwtstamps.
 	 */
-	if (!(tsyncrxctl & IXGBE_TSYNCRXCTL_VALID))
+	if (unlikely(!ixgbe_test_staterr(rx_desc, IXGBE_RXDADV_STAT_TS)))
 		return;
 
 	spin_lock_irqsave(&adapter->tmreg_lock, flags);
@@ -539,6 +621,11 @@ void ixgbe_ptp_rx_hwtstamp(struct ixgbe_q_vector *q_vector,
  * type has to be specified. Matching the kind of event packet is
  * not supported, with the exception of "all V2 events regardless of
  * level 2 or 4".
+ *
+ * Since hardware always timestamps Path delay packets when timestamping V2
+ * packets, regardless of the type specified in the register, only use V2
+ * Event mode. This more accurately tells the user what the hardware is going
+ * to do anyways.
  */
 int ixgbe_ptp_hwtstamp_ioctl(struct ixgbe_adapter *adapter,
 			     struct ifreq *ifr, int cmd)
@@ -582,41 +669,30 @@ int ixgbe_ptp_hwtstamp_ioctl(struct ixgbe_adapter *adapter,
 		tsync_rx_mtrl = IXGBE_RXMTRL_V1_DELAY_REQ_MSG;
 		is_l4 = true;
 		break;
+	case HWTSTAMP_FILTER_PTP_V2_EVENT:
+	case HWTSTAMP_FILTER_PTP_V2_L2_EVENT:
+	case HWTSTAMP_FILTER_PTP_V2_L4_EVENT:
 	case HWTSTAMP_FILTER_PTP_V2_SYNC:
 	case HWTSTAMP_FILTER_PTP_V2_L2_SYNC:
 	case HWTSTAMP_FILTER_PTP_V2_L4_SYNC:
-		tsync_rx_ctl |= IXGBE_TSYNCRXCTL_TYPE_L2_L4_V2;
-		tsync_rx_mtrl = IXGBE_RXMTRL_V2_SYNC_MSG;
-		is_l2 = true;
-		is_l4 = true;
-		config.rx_filter = HWTSTAMP_FILTER_SOME;
-		break;
 	case HWTSTAMP_FILTER_PTP_V2_DELAY_REQ:
 	case HWTSTAMP_FILTER_PTP_V2_L2_DELAY_REQ:
 	case HWTSTAMP_FILTER_PTP_V2_L4_DELAY_REQ:
-		tsync_rx_ctl |= IXGBE_TSYNCRXCTL_TYPE_L2_L4_V2;
-		tsync_rx_mtrl = IXGBE_RXMTRL_V2_DELAY_REQ_MSG;
-		is_l2 = true;
-		is_l4 = true;
-		config.rx_filter = HWTSTAMP_FILTER_SOME;
-		break;
-	case HWTSTAMP_FILTER_PTP_V2_L4_EVENT:
-	case HWTSTAMP_FILTER_PTP_V2_L2_EVENT:
-	case HWTSTAMP_FILTER_PTP_V2_EVENT:
 		tsync_rx_ctl |= IXGBE_TSYNCRXCTL_TYPE_EVENT_V2;
-		config.rx_filter = HWTSTAMP_FILTER_PTP_V2_EVENT;
 		is_l2 = true;
 		is_l4 = true;
+		config.rx_filter = HWTSTAMP_FILTER_PTP_V2_EVENT;
 		break;
 	case HWTSTAMP_FILTER_PTP_V1_L4_EVENT:
 	case HWTSTAMP_FILTER_ALL:
 	default:
 		/*
-		 * register RXMTRL must be set, therefore it is not
-		 * possible to time stamp both V1 Sync and Delay_Req messages
-		 * and hardware does not support timestamping all packets
-		 * => return error
+		 * register RXMTRL must be set in order to do V1 packets,
+		 * therefore it is not possible to time stamp both V1 Sync and
+		 * Delay_Req messages and hardware does not support
+		 * timestamping all packets => return error
 		 */
+		config.rx_filter = HWTSTAMP_FILTER_NONE;
 		return -ERANGE;
 	}
 
@@ -626,6 +702,9 @@ int ixgbe_ptp_hwtstamp_ioctl(struct ixgbe_adapter *adapter,
 		return 0;
 	}
 
+	/* Store filter value for later use */
+	adapter->rx_hwtstamp_filter = config.rx_filter;
+
 	/* define ethertype filter for timestamped packets */
 	if (is_l2)
 		IXGBE_WRITE_REG(hw, IXGBE_ETQF(3),
@@ -861,6 +940,10 @@ void ixgbe_ptp_init(struct ixgbe_adapter *adapter)
 		return;
 	}
 
+	/* initialize the ptp filter */
+	if (ptp_filter_init(ptp_filter, ARRAY_SIZE(ptp_filter)))
+		e_dev_warn("ptp_filter_init failed\n");
+
 	spin_lock_init(&adapter->tmreg_lock);
 
 	ixgbe_ptp_start_cyclecounter(adapter);

drivers/net/ethernet/intel/ixgbe/ixgbe_sysfs.c

@@ -37,7 +37,6 @@
 #include <linux/netdevice.h>
 #include <linux/hwmon.h>
 
-#ifdef CONFIG_IXGBE_HWMON
 /* hwmon callback functions */
 static ssize_t ixgbe_hwmon_show_location(struct device *dev,
 					 struct device_attribute *attr,
@@ -241,5 +240,4 @@ int ixgbe_sysfs_init(struct ixgbe_adapter *adapter)
 exit:
 	return rc;
 }
-#endif /* CONFIG_IXGBE_HWMON */
 

drivers/net/ethernet/intel/ixgbe/ixgbe_type.h

@@ -2419,7 +2419,7 @@ typedef u32 ixgbe_physical_layer;
  */
 
 /* BitTimes (BT) conversion */
-#define IXGBE_BT2KB(BT) ((BT + 1023) / (8 * 1024))
+#define IXGBE_BT2KB(BT) ((BT + (8 * 1024 - 1)) / (8 * 1024))
 #define IXGBE_B2BT(BT) (BT * 8)
 
 /* Calculate Delay to respond to PFC */
@@ -2450,24 +2450,31 @@ typedef u32 ixgbe_physical_layer;
 #define IXGBE_PCI_DELAY	10000
 
 /* Calculate X540 delay value in bit times */
-#define IXGBE_FILL_RATE (36 / 25)
-
-#define IXGBE_DV_X540(LINK, TC) (IXGBE_FILL_RATE * \
-				 (IXGBE_B2BT(LINK) + IXGBE_PFC_D + \
+#define IXGBE_DV_X540(_max_frame_link, _max_frame_tc) \
+			((36 * \
+			  (IXGBE_B2BT(_max_frame_link) + \
+			   IXGBE_PFC_D + \
 			   (2 * IXGBE_CABLE_DC) + \
 			   (2 * IXGBE_ID_X540) + \
-				 IXGBE_HD + IXGBE_B2BT(TC)))
+			   IXGBE_HD) / 25 + 1) + \
+			 2 * IXGBE_B2BT(_max_frame_tc))
 
 /* Calculate 82599, 82598 delay value in bit times */
-#define IXGBE_DV(LINK, TC) (IXGBE_FILL_RATE * \
-			    (IXGBE_B2BT(LINK) + IXGBE_PFC_D + \
-			    (2 * IXGBE_CABLE_DC) + (2 * IXGBE_ID) + \
-			    IXGBE_HD + IXGBE_B2BT(TC)))
+#define IXGBE_DV(_max_frame_link, _max_frame_tc) \
+			((36 * \
+			  (IXGBE_B2BT(_max_frame_link) + \
+			   IXGBE_PFC_D + \
+			   (2 * IXGBE_CABLE_DC) + \
+			   (2 * IXGBE_ID) + \
+			   IXGBE_HD) / 25 + 1) + \
+			 2 * IXGBE_B2BT(_max_frame_tc))
 
 /* Calculate low threshold delay values */
-#define IXGBE_LOW_DV_X540(TC) (2 * IXGBE_B2BT(TC) + \
-			       (IXGBE_FILL_RATE * IXGBE_PCI_DELAY))
-#define IXGBE_LOW_DV(TC)      (2 * IXGBE_LOW_DV_X540(TC))
+#define IXGBE_LOW_DV_X540(_max_frame_tc) \
+			(2 * IXGBE_B2BT(_max_frame_tc) + \
+			(36 * IXGBE_PCI_DELAY / 25) + 1)
+#define IXGBE_LOW_DV(_max_frame_tc) \
+			(2 * IXGBE_LOW_DV_X540(_max_frame_tc))
 
 /* Software ATR hash keys */
 #define IXGBE_ATR_BUCKET_HASH_KEY    0x3DAD14E2