Commit 93cffffa authored by Bjorn Helgaas's avatar Bjorn Helgaas Committed by Linus Torvalds

[PATCH] PCI: do VIA IRQ fixup always, not just in PIC mode

At least some VIA chipsets require the fixup even in IO-APIC mode.

This was found and debugged with the patient assistance of Stian
Jordet <liste@jordet.nu> on an Asus CUV266-DLS motherboard.
Signed-off-by: default avatarBjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: default avatarGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: default avatarAndrew Morton <akpm@osdl.org>
Signed-off-by: default avatarLinus Torvalds <torvalds@osdl.org>
parent a86d1f43
......@@ -459,17 +459,6 @@ DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_8131_APIC,
#endif /* CONFIG_X86_IO_APIC */
/*
* Via 686A/B: The PCI_INTERRUPT_LINE register for the on-chip
* devices, USB0/1, AC97, MC97, and ACPI, has an unusual feature:
* when written, it makes an internal connection to the PIC.
* For these devices, this register is defined to be 4 bits wide.
* Normally this is fine. However for IO-APIC motherboards, or
* non-x86 architectures (yes Via exists on PPC among other places),
* we must mask the PCI_INTERRUPT_LINE value versus 0xf to get
* interrupts delivered properly.
*/
/*
* FIXME: it is questionable that quirk_via_acpi
* is needed. It shows up as an ISA bridge, and does not
......@@ -492,28 +481,30 @@ static void __devinit quirk_via_acpi(struct pci_dev *d)
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C586_3, quirk_via_acpi );
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C686_4, quirk_via_acpi );
static void quirk_via_irqpic(struct pci_dev *dev)
/*
* Via 686A/B: The PCI_INTERRUPT_LINE register for the on-chip
* devices, USB0/1, AC97, MC97, and ACPI, has an unusual feature:
* when written, it makes an internal connection to the PIC.
* For these devices, this register is defined to be 4 bits wide.
* Normally this is fine. However for IO-APIC motherboards, or
* non-x86 architectures (yes Via exists on PPC among other places),
* we must mask the PCI_INTERRUPT_LINE value versus 0xf to get
* interrupts delivered properly.
*/
static void quirk_via_irq(struct pci_dev *dev)
{
u8 irq, new_irq;
#ifdef CONFIG_X86_IO_APIC
if (nr_ioapics && !skip_ioapic_setup)
return;
#endif
#ifdef CONFIG_ACPI
if (acpi_irq_model != ACPI_IRQ_MODEL_PIC)
return;
#endif
new_irq = dev->irq & 0xf;
pci_read_config_byte(dev, PCI_INTERRUPT_LINE, &irq);
if (new_irq != irq) {
printk(KERN_INFO "PCI: Via PIC IRQ fixup for %s, from %d to %d\n",
printk(KERN_INFO "PCI: Via IRQ fixup for %s, from %d to %d\n",
pci_name(dev), irq, new_irq);
udelay(15); /* unknown if delay really needed */
pci_write_config_byte(dev, PCI_INTERRUPT_LINE, new_irq);
}
}
DECLARE_PCI_FIXUP_ENABLE(PCI_VENDOR_ID_VIA, PCI_ANY_ID, quirk_via_irqpic);
DECLARE_PCI_FIXUP_ENABLE(PCI_VENDOR_ID_VIA, PCI_ANY_ID, quirk_via_irq);
/*
* PIIX3 USB: We have to disable USB interrupts that are
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment