[PATCH] Merged hid-lgff.c and hid-lg3d.c

Here is a patch wich moves hid-lg3d.c into hid-lgff.c. This allows to
share the init code.
A side-effect of this merge is that rumble pads are now handled the same
way joysticks are. Instead of having one timer per effect, executing
only when needed, we have one timer executing at regular intervals going
over each effect.

drivers/usb/input/Config.help

@@ -30,10 +30,13 @@ CONFIG_HID_FF
 
   If unsure, say N.
 
-CONFIG_LOGITECH_RUMBLE
-  Say Y here if you have a Logitech WingMan Cordless rumble pad and if you
-  want to enable force feedback. Note: if you say N here, this device will
-  still be supported, but without force feedback.
+CONFIG_LOGITECH_FF
+  Say Y here if you have one of these devices:
+  - Logitech WingMan Cordless RumblePad
+  - Logitech WingMan Force 3D
+  and if you want to enable force feedback for them.
+  Note: if you say N here, this device will still be supported, but without
+  force feedback.
 
 CONFIG_HID_PID
   Say Y here if you have a PID-compliant joystick and wish to enable force

drivers/usb/input/Config.in

@@ -11,8 +11,7 @@ fi
 dep_mbool '    HID input layer support' CONFIG_USB_HIDINPUT $CONFIG_INPUT $CONFIG_USB_HID
 dep_mbool '      Force feedback support (EXPERIMENTAL)' CONFIG_HID_FF $CONFIG_USB_HIDINPUT $CONFIG_EXPERIMENTAL
 dep_mbool '        PID Devices' CONFIG_HID_PID $CONFIG_USB_HID $CONFIG_HID_FF
-dep_mbool '        Logitech RumblePad support' CONFIG_LOGITECH_RUMBLE $CONFIG_USB_HID $CONFIG_HID_FF
-dep_mbool '        Logitech WingMan Force 3D support' CONFIG_LOGITECH_3D $CONFIG_USB_HID $CONFIG_HID_FF
+dep_mbool '        Logitech WingMan *3D support' CONFIG_LOGITECH_FF $CONFIG_USB_HID $CONFIG_HID_FF
 dep_mbool '    /dev/hiddev raw HID device support' CONFIG_USB_HIDDEV $CONFIG_USB_HID
 
 if [ "$CONFIG_USB_HID" != "y" ]; then

drivers/usb/input/Makefile

@@ -16,12 +16,9 @@ endif
 ifeq ($(CONFIG_HID_PID),y)
 	hid-objs	+= pid.o
 endif
-ifeq ($(CONFIG_LOGITECH_RUMBLE),y)
+ifeq ($(CONFIG_LOGITECH_FF),y)
 	hid-objs	+= hid-lgff.o
 endif
-ifeq ($(CONFIG_LOGITECH_3D),y)
-	hid-objs	+= hid-lg3dff.o
-endif
 ifeq ($(CONFIG_HID_FF),y)
 	hid-objs	+= hid-ff.o
 endif

drivers/usb/input/hid-ff.c

 /*
- * $Id: hid-ff.c,v 1.3 2002/06/09 11:06:38 jdeneux Exp $
+ * $Id: hid-ff.c,v 1.2 2002/04/18 22:02:47 jdeneux Exp $
  *
  *  Force feedback support for hid devices.
  *  Not all hid devices use the same protocol. For example, some use PID,
@@ -44,17 +44,15 @@ extern int hid_pid_init(struct hid_device* hid);
  * devices, you need to add the USB vendor and product ids here.
  */
 struct hid_ff_initializer {
-	__u16 idVendor;
-	__u16 idProduct;
+	u16 idVendor;
+	u16 idProduct;
 	int (*init)(struct hid_device*);
 };
 
 static struct hid_ff_initializer inits[] = {
-#ifdef CONFIG_LOGITECH_RUMBLE
+#ifdef CONFIG_LOGITECH_FF
 	{0x46d, 0xc211, hid_lgff_init},
-#endif
-#ifdef CONFIG_LOGITECH_3D
-	{0x46d, 0xc283, hid_lg3d_init},
+	{0x46d, 0xc283, hid_lgff_init},
 #endif
 #ifdef CONFIG_HID_PID
 	{0x45e, 0x001b, hid_pid_init},