ARM: dts: sbc-t54: add support for sbc-t54 with cm-t54

Add support for CM-T54 CoM and SBC-T54 board:

http://compulab.co.il/products/computer-on-modules/cm-t54/
http://compulab.co.il/products/sbcs/sbc-t54/

SBC-T54 is a single board computer based on OMAP5432 CPU.
It is implemented with a CM-T54 CoM providing most of the functions,
and SB-T54 carrier board providing connectors and several additional
functions.

Added basic support for:

* PMIC
* LED
* MMC/SD
* eMMC
* USB
* I2C1/4
* SB-T54 and CM-T54 EEPROMs
* RTC
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
[tony@atomide.com: updated for Makefile sorting]
Signed-off-by: Tony Lindgren <tony@atomide.com>

arch/arm/boot/dts/Makefile

@@ -287,7 +287,9 @@ dtb-$(CONFIG_ARCH_OMAP4) += omap4-duovero-parlor.dtb \
 	omap4-var-som.dtb
 dtb-$(CONFIG_SOC_AM43XX) += am43x-epos-evm.dtb \
 	am437x-gp-evm.dtb
-dtb-$(CONFIG_SOC_OMAP5) += omap5-uevm.dtb
+dtb-$(CONFIG_SOC_OMAP5) += omap5-cm-t54.dtb \
+	omap5-sbc-t54.dtb \
+	omap5-uevm.dtb
 dtb-$(CONFIG_SOC_DRA7XX) += dra7-evm.dtb
 dtb-$(CONFIG_ARCH_ORION5X) += orion5x-lacie-ethernet-disk-mini-v2.dtb
 dtb-$(CONFIG_ARCH_PRIMA2) += prima2-evb.dtb

arch/arm/boot/dts/omap5-cm-t54.dts

+/*
+ * Support for CompuLab CM-T54
+ */
+/dts-v1/;
+
+#include "omap5.dtsi"
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+/ {
+	model = "CompuLab CM-T54";
+	compatible = "compulab,omap5-cm-t54", "ti,omap5";
+
+	memory {
+		device_type = "memory";
+		reg = <0x80000000 0x7F000000>; /* 2048 MB */
+	};
+
+	vmmcsd_fixed: fixed-regulator-mmcsd {
+		compatible = "regulator-fixed";
+		regulator-name = "vmmcsd_fixed";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	/* HS USB Host PHY on PORT 2 */
+	hsusb2_phy: hsusb2_phy {
+		compatible = "usb-nop-xceiv";
+		reset-gpios = <&gpio3 12 GPIO_ACTIVE_LOW>; /* gpio3_76 HUB_RESET */
+	};
+
+	/* HS USB Host PHY on PORT 3 */
+	hsusb3_phy: hsusb3_phy {
+		compatible = "usb-nop-xceiv";
+		reset-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>; /* gpio3_83 ETH_RESET */
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		led@1 {
+			label = "Heartbeat";
+			gpios = <&gpio3 16 GPIO_ACTIVE_HIGH>; /* gpio3_80 ACT_LED */
+			linux,default-trigger = "heartbeat";
+			default-state = "off";
+		};
+	};
+};
+
+&omap5_pmx_core {
+	pinctrl-names = "default";
+	pinctrl-0 = <
+			&led_gpio_pins
+			&usbhost_pins
+	>;
+
+	led_gpio_pins: pinmux_led_gpio_pins {
+		pinctrl-single,pins = <
+			OMAP5_CORE_IOPAD(0x28b0, PIN_OUTPUT | MUX_MODE6) /* hsi2_caflag.gpio3_80 */
+		>;
+	};
+
+	i2c1_pins: pinmux_i2c1_pins {
+		pinctrl-single,pins = <
+			OMAP5_CORE_IOPAD(0x29f2, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_pmic_scl */
+			OMAP5_CORE_IOPAD(0x29f4, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_pmic_sda */
+		>;
+	};
+
+	mmc1_pins: pinmux_mmc1_pins {
+		pinctrl-single,pins = <
+			OMAP5_CORE_IOPAD(0x29e2, PIN_INPUT_PULLUP | MUX_MODE0) /* sdcard_clk */
+			OMAP5_CORE_IOPAD(0x29e4, PIN_INPUT_PULLUP | MUX_MODE0) /* sdcard_cmd */
+			OMAP5_CORE_IOPAD(0x29e6, PIN_INPUT_PULLUP | MUX_MODE0) /* sdcard_data2 */
+			OMAP5_CORE_IOPAD(0x29e8, PIN_INPUT_PULLUP | MUX_MODE0) /* sdcard_data3 */
+			OMAP5_CORE_IOPAD(0x29ea, PIN_INPUT_PULLUP | MUX_MODE0) /* sdcard_data0 */
+			OMAP5_CORE_IOPAD(0x29ec, PIN_INPUT_PULLUP | MUX_MODE0) /* sdcard_data1 */
+		>;
+	};
+
+	mmc2_pins: pinmux_mmc2_pins {
+		pinctrl-single,pins = <
+			OMAP5_CORE_IOPAD(0x2840, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_clk */
+			OMAP5_CORE_IOPAD(0x2842, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_cmd */
+			OMAP5_CORE_IOPAD(0x2844, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_data0 */
+			OMAP5_CORE_IOPAD(0x2846, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_data1 */
+			OMAP5_CORE_IOPAD(0x2848, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_data2 */
+			OMAP5_CORE_IOPAD(0x284a, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_data3 */
+			OMAP5_CORE_IOPAD(0x284c, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_data4 */
+			OMAP5_CORE_IOPAD(0x284e, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_data5 */
+			OMAP5_CORE_IOPAD(0x2850, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_data6 */
+			OMAP5_CORE_IOPAD(0x2852, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_data7 */
+		>;
+	};
+
+	usbhost_pins: pinmux_usbhost_pins {
+		pinctrl-single,pins = <
+			OMAP5_CORE_IOPAD(0x28c4, PIN_INPUT | MUX_MODE0)  /* usbb2_hsic_strobe */
+			OMAP5_CORE_IOPAD(0x28c6, PIN_INPUT | MUX_MODE0)  /* usbb2_hsic_data */
+
+			OMAP5_CORE_IOPAD(0x29dc, PIN_INPUT | MUX_MODE0)  /* usbb3_hsic_strobe */
+			OMAP5_CORE_IOPAD(0x29de, PIN_INPUT | MUX_MODE0)  /* usbb3_hsic_data */
+
+			OMAP5_CORE_IOPAD(0x28a8, PIN_OUTPUT | MUX_MODE6) /* hsi2_caready.gpio3_76 */
+			OMAP5_CORE_IOPAD(0x28b6, PIN_OUTPUT | MUX_MODE6) /* hsi2_acdata.gpio3_83 */
+		>;
+	};
+};
+
+&mmc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc1_pins>;
+	vmmc-supply = <&ldo9_reg>;
+	bus-width = <4>;
+};
+
+&mmc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc2_pins>;
+	vmmc-supply = <&vmmcsd_fixed>;
+	bus-width = <8>;
+	ti,non-removable;
+};
+
+&mmc4 {
+	status = "disabled";
+};
+
+&mmc5 {
+	status = "disabled";
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins>;
+
+	clock-frequency = <400000>;
+
+	at24@50 {
+		compatible = "at24,24c02";
+		pagesize = <16>;
+		reg = <0x50>;
+	};
+
+	palmas: palmas@48 {
+		compatible = "ti,palmas";
+		interrupts = <GIC_SPI 7 IRQ_TYPE_NONE>; /* IRQ_SYS_1N */
+		interrupt-parent = <&gic>;
+		reg = <0x48>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		ti,system-power-controller;
+
+		extcon_usb3: palmas_usb {
+			compatible = "ti,palmas-usb-vid";
+			ti,enable-vbus-detection;
+			ti,enable-id-detection;
+			ti,wakeup;
+		};
+
+		rtc {
+			compatible = "ti,palmas-rtc";
+			interrupt-parent = <&palmas>;
+			interrupts = <8 IRQ_TYPE_NONE>;
+		};
+
+		palmas_pmic {
+			compatible = "ti,palmas-pmic";
+			interrupt-parent = <&palmas>;
+			interrupts = <14 IRQ_TYPE_NONE>;
+			interrupt-name = "short-irq";
+
+			ti,ldo6-vibrator;
+
+			regulators {
+				smps123_reg: smps123 {
+					/* VDD_OPP_MPU */
+					regulator-name = "smps123";
+					regulator-min-microvolt = < 600000>;
+					regulator-max-microvolt = <1500000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				smps45_reg: smps45 {
+					/* VDD_OPP_MM */
+					regulator-name = "smps45";
+					regulator-min-microvolt = < 600000>;
+					regulator-max-microvolt = <1310000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				smps6_reg: smps6 {
+					/* VDD_DDR3 - over VDD_SMPS6 */
+					regulator-name = "smps6";
+					regulator-min-microvolt = <1500000>;
+					regulator-max-microvolt = <1500000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				smps7_reg: smps7 {
+					/* VDDS_1v8_OMAP over VDDS_1v8_MAIN */
+					regulator-name = "smps7";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				smps8_reg: smps8 {
+					/* VDD_OPP_CORE */
+					regulator-name = "smps8";
+					regulator-min-microvolt = < 600000>;
+					regulator-max-microvolt = <1310000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				smps9_reg: smps9 {
+					/* VDDA_2v1_AUD over VDD_2v1 */
+					regulator-name = "smps9";
+					regulator-min-microvolt = <3300000>;
+					regulator-max-microvolt = <3300000>;
+					ti,smps-range = <0x80>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				smps10_out2_reg: smps10_out2 {
+					/* VBUS_5V_OTG */
+					regulator-name = "smps10_out2";
+					regulator-min-microvolt = <5000000>;
+					regulator-max-microvolt = <5000000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				smps10_out1_reg: smps10_out1 {
+					/* VBUS_5V_OTG */
+					regulator-name = "smps10_out1";
+					regulator-min-microvolt = <5000000>;
+					regulator-max-microvolt = <5000000>;
+				};
+
+				ldo1_reg: ldo1 {
+					/* VDDAPHY_CAM: vdda_csiport */
+					regulator-name = "ldo1";
+					regulator-min-microvolt = <1500000>;
+					regulator-max-microvolt = <1800000>;
+				};
+
+				ldo2_reg: ldo2 {
+					/* VDD_3V3_WLAN */
+					regulator-name = "ldo2";
+					regulator-min-microvolt = <3300000>;
+					regulator-max-microvolt = <3300000>;
+					regulator-boot-on;
+				};
+
+				ldo3_reg: ldo3 {
+					/* VCC_1V5_AUD */
+					regulator-name = "ldo3";
+					regulator-min-microvolt = <1500000>;
+					regulator-max-microvolt = <1500000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				ldo4_reg: ldo4 {
+					/* VDDAPHY_DISP: vdda_dsiport/hdmi */
+					regulator-name = "ldo4";
+					regulator-min-microvolt = <1500000>;
+					regulator-max-microvolt = <1800000>;
+				};
+
+				ldo5_reg: ldo5 {
+					/* VDDA_1V8_PHY: usb/sata/hdmi.. */
+					regulator-name = "ldo5";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				ldo6_reg: ldo6 {
+					/* VDDS_1V2_WKUP: hsic/ldo_emu_wkup */
+					regulator-name = "ldo6";
+					regulator-min-microvolt = <1200000>;
+					regulator-max-microvolt = <1200000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				ldo7_reg: ldo7 {
+					/* VDD_VPP: vpp1 */
+					regulator-name = "ldo7";
+					regulator-min-microvolt = <2000000>;
+					regulator-max-microvolt = <2000000>;
+					/* Only for efuse reprograming! */
+					status = "disabled";
+				};
+
+				ldo8_reg: ldo8 {
+					/* VDD_3v0: Does not go anywhere */
+					regulator-name = "ldo8";
+					regulator-min-microvolt = <3000000>;
+					regulator-max-microvolt = <3000000>;
+					regulator-boot-on;
+					/* Unused */
+					status = "disabled";
+				};
+
+				ldo9_reg: ldo9 {
+					/* VCC_DV_SDIO: vdds_sdcard */
+					regulator-name = "ldo9";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <3000000>;
+					regulator-boot-on;
+				};
+
+				ldoln_reg: ldoln {
+					/* VDDA_1v8_REF: vdds_osc/mm_l4per.. */
+					regulator-name = "ldoln";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				ldousb_reg: ldousb {
+					/* VDDA_3V_USB: VDDA_USBHS33 */
+					regulator-name = "ldousb";
+					regulator-min-microvolt = <3250000>;
+					regulator-max-microvolt = <3250000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				regen3_reg: regen3 {
+					/* REGEN3 controls LDO9 supply to card */
+					regulator-name = "regen3";
+					regulator-always-on;
+					regulator-boot-on;
+				};
+			};
+		};
+	};
+};
+
+&usbhshost {
+	port2-mode = "ehci-hsic";
+	port3-mode = "ehci-hsic";
+};
+
+&usbhsehci {
+	phys = <0 &hsusb2_phy &hsusb3_phy>;
+};
+
+&cpu0 {
+	cpu0-supply = <&smps123_reg>;
+};

arch/arm/boot/dts/omap5-sbc-t54.dts

+/*
+ * Suppport for CompuLab SBC-T54 with CM-T54
+ */
+
+#include "omap5-cm-t54.dts"
+
+/ {
+	model = "CompuLab SBC-T54 with CM-T54";
+	compatible = "compulab,omap5-sbc-t54", "compulab,omap5-cm-t54", "ti,omap5";
+};
+
+&omap5_pmx_core {
+	i2c4_pins: pinmux_i2c4_pins {
+		pinctrl-single,pins = <
+			OMAP5_CORE_IOPAD(0x28f8, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c4_scl */
+			OMAP5_CORE_IOPAD(0x28fa, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c4_sda */
+		>;
+	};
+
+	mmc1_aux_pins: pinmux_mmc1_aux_pins {
+		pinctrl-single,pins = <
+			OMAP5_CORE_IOPAD(0x2974, PIN_INPUT_PULLUP | MUX_MODE6) /* gpio8_228 */
+			OMAP5_CORE_IOPAD(0x2976, PIN_INPUT_PULLUP | MUX_MODE6) /* gpio8_229 */
+		>;
+	};
+};
+
+&mmc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <
+		&mmc1_pins
+		&mmc1_aux_pins
+	>;
+	cd-inverted;
+	wp-inverted;
+	cd-gpios = <&gpio8 4 GPIO_ACTIVE_LOW>; /* gpio8_228 */
+	wp-gpios = <&gpio8 5 GPIO_ACTIVE_LOW>; /* gpio8_229 */
+};
+
+&i2c4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c4_pins>;
+
+	clock-frequency = <400000>;
+
+	at24@50 {
+		compatible = "at24,24c02";
+		pagesize = <16>;
+		reg = <0x50>;
+	};
+};