Merge branch 'topic/oss-fix' into for-linus

Documentation/sound/oss/CS4232

-To configure the Crystal CS423x sound chip and activate its DSP functions,
-modules may be loaded in this order:
-  
-	modprobe sound
-	insmod ad1848
-	insmod uart401
-	insmod cs4232 io=* irq=* dma=* dma2=*
-  
-This is the meaning of the parameters:
-  
-	io--I/O address of the Windows Sound System (normally 0x534)
-	irq--IRQ of this device
-	dma and dma2--DMA channels (DMA2 may be 0)
-  
-On some cards, the board attempts to do non-PnP setup, and fails.  If you
-have problems, use Linux' PnP facilities. 
-  
-To get MIDI facilities add
-  
-	insmod opl3 io=*
-  
-where "io" is the I/O address of the OPL3 synthesizer. This will be shown
-in /proc/sys/pnp and is normally 0x388.

Documentation/sound/oss/Introduction

@@ -80,7 +80,7 @@ Notes:
     additional features.
 
 2.  The commercial OSS driver may be obtained from the site:
-    http://www/opensound.com.  This may be used for cards that
+    http://www.opensound.com.  This may be used for cards that
     are unsupported by the kernel driver, or may be used
     by other operating systems.  
 

sound/oss/ad1848.c

@@ -280,7 +280,7 @@ static void wait_for_calibration(ad1848_info * devc)
 	while (timeout > 0 && (ad_read(devc, 11) & 0x20))
 		timeout--;
 	if (ad_read(devc, 11) & 0x20)
-		if ( (devc->model != MD_1845) || (devc->model != MD_1845_SSCAPE))
+		if ((devc->model != MD_1845) && (devc->model != MD_1845_SSCAPE))
 			printk(KERN_WARNING "ad1848: Auto calibration timed out(3).\n");
 }
 
@@ -2107,7 +2107,7 @@ int ad1848_control(int cmd, int arg)
 	switch (cmd)
 	{
 		case AD1848_SET_XTAL:	/* Change clock frequency of AD1845 (only ) */
-			if (devc->model != MD_1845 || devc->model != MD_1845_SSCAPE)
+			if (devc->model != MD_1845 && devc->model != MD_1845_SSCAPE)
 				return -EINVAL;
 			spin_lock_irqsave(&devc->lock,flags);
 			ad_enter_MCE(devc);

sound/oss/dmabuf.c

@@ -439,7 +439,7 @@ int DMAbuf_sync(int dev)
 			DMAbuf_launch_output(dev, dmap);
 		adev->dmap_out->flags |= DMA_SYNCING;
 		adev->dmap_out->underrun_count = 0;
-		while (!signal_pending(current) && n++ <= adev->dmap_out->nbufs && 
+		while (!signal_pending(current) && n++ < adev->dmap_out->nbufs &&
 		       adev->dmap_out->qlen && adev->dmap_out->underrun_count == 0) {
 			long t = dmabuf_timeout(dmap);
 			spin_unlock_irqrestore(&dmap->lock,flags);

sound/oss/pas2_card.c

@@ -156,9 +156,7 @@ static int __init config_pas_hw(struct address_info *hw_config)
 						 * 0x80
 						 */ , 0xB88);
 
-	pas_write(0x80
-		  | joystick?0x40:0
-		  ,0xF388);
+	pas_write(0x80 | (joystick ? 0x40 : 0), 0xF388);
 
 	if (pas_irq < 0 || pas_irq > 15)
 	{

sound/oss/pss.c

@@ -457,10 +457,9 @@ static void pss_mixer_reset(pss_confdata *devc)
 	}
 }
 
-static int set_volume_mono(unsigned __user *p, int *aleft)
+static int set_volume_mono(unsigned __user *p, unsigned int *aleft)
 {
-	int left;
-	unsigned volume;
+	unsigned int left, volume;
 	if (get_user(volume, p))
 		return -EFAULT;
 	
@@ -471,10 +470,11 @@ static int set_volume_mono(unsigned __user *p, int *aleft)
 	return 0;
 }
 
-static int set_volume_stereo(unsigned __user *p, int *aleft, int *aright)
+static int set_volume_stereo(unsigned __user *p,
+			     unsigned int *aleft,
+			     unsigned int *aright)
 {
-	int left, right;
-	unsigned volume;
+	unsigned int left, right, volume;
 	if (get_user(volume, p))
 		return -EFAULT;
 

sound/oss/sequencer.c

@@ -212,7 +212,6 @@ int sequencer_write(int dev, struct file *file, const char __user *buf, int coun
 {
 	unsigned char event_rec[EV_SZ], ev_code;
 	int p = 0, c, ev_size;
-	int err;
 	int mode = translate_mode(file);
 
 	dev = dev >> 4;
@@ -285,7 +284,7 @@ int sequencer_write(int dev, struct file *file, const char __user *buf, int coun
 		{
 			if (!midi_opened[event_rec[2]])
 			{
-				int mode;
+				int err, mode;
 				int dev = event_rec[2];
 
 				if (dev >= max_mididev || midi_devs[dev]==NULL)