Commit a2b95646 authored by Rob Herring's avatar Rob Herring

dt-bindings: arm: l2x0: Convert L2 cache to json-schema

Convert the ARM L2 cache controller binding to json-schema.
Signed-off-by: default avatarRob Herring <robh@kernel.org>
parent 42e45a94
* ARM L2 Cache Controller
ARM cores often have a separate L2C210/L2C220/L2C310 (also known as PL210/PL220/
PL310 and variants) based level 2 cache controller. All these various implementations
of the L2 cache controller have compatible programming models (Note 1).
Some of the properties that are just prefixed "cache-*" are taken from section
3.7.3 of the Devicetree Specification which can be found at:
https://www.devicetree.org/specifications/
The ARM L2 cache representation in the device tree should be done as follows:
Required properties:
- compatible : should be one of:
"arm,pl310-cache"
"arm,l220-cache"
"arm,l210-cache"
"bcm,bcm11351-a2-pl310-cache": DEPRECATED by "brcm,bcm11351-a2-pl310-cache"
"brcm,bcm11351-a2-pl310-cache": For Broadcom bcm11351 chipset where an
offset needs to be added to the address before passing down to the L2
cache controller
"marvell,aurora-system-cache": Marvell Controller designed to be
compatible with the ARM one, with system cache mode (meaning
maintenance operations on L1 are broadcasted to the L2 and L2
performs the same operation).
"marvell,aurora-outer-cache": Marvell Controller designed to be
compatible with the ARM one with outer cache mode.
"marvell,tauros3-cache": Marvell Tauros3 cache controller, compatible
with arm,pl310-cache controller.
- cache-unified : Specifies the cache is a unified cache.
- cache-level : Should be set to 2 for a level 2 cache.
- reg : Physical base address and size of cache controller's memory mapped
registers.
Optional properties:
- arm,data-latency : Cycles of latency for Data RAM accesses. Specifies 3 cells of
read, write and setup latencies. Minimum valid values are 1. Controllers
without setup latency control should use a value of 0.
- arm,tag-latency : Cycles of latency for Tag RAM accesses. Specifies 3 cells of
read, write and setup latencies. Controllers without setup latency control
should use 0. Controllers without separate read and write Tag RAM latency
values should only use the first cell.
- arm,dirty-latency : Cycles of latency for Dirty RAMs. This is a single cell.
- arm,filter-ranges : <start length> Starting address and length of window to
filter. Addresses in the filter window are directed to the M1 port. Other
addresses will go to the M0 port.
- arm,io-coherent : indicates that the system is operating in an hardware
I/O coherent mode. Valid only when the arm,pl310-cache compatible
string is used.
- interrupts : 1 combined interrupt.
- cache-size : specifies the size in bytes of the cache
- cache-sets : specifies the number of associativity sets of the cache
- cache-block-size : specifies the size in bytes of a cache block
- cache-line-size : specifies the size in bytes of a line in the cache,
if this is not specified, the line size is assumed to be equal to the
cache block size
- cache-id-part: cache id part number to be used if it is not present
on hardware
- wt-override: If present then L2 is forced to Write through mode
- arm,double-linefill : Override double linefill enable setting. Enable if
non-zero, disable if zero.
- arm,double-linefill-incr : Override double linefill on INCR read. Enable
if non-zero, disable if zero.
- arm,double-linefill-wrap : Override double linefill on WRAP read. Enable
if non-zero, disable if zero.
- arm,prefetch-drop : Override prefetch drop enable setting. Enable if non-zero,
disable if zero.
- arm,prefetch-offset : Override prefetch offset value. Valid values are
0-7, 15, 23, and 31.
- arm,shared-override : The default behavior of the L220 or PL310 cache
controllers with respect to the shareable attribute is to transform "normal
memory non-cacheable transactions" into "cacheable no allocate" (for reads)
or "write through no write allocate" (for writes).
On systems where this may cause DMA buffer corruption, this property must be
specified to indicate that such transforms are precluded.
- arm,parity-enable : enable parity checking on the L2 cache (L220 or PL310).
- arm,parity-disable : disable parity checking on the L2 cache (L220 or PL310).
- arm,outer-sync-disable : disable the outer sync operation on the L2 cache.
Some core tiles, especially ARM PB11MPCore have a faulty L220 cache that
will randomly hang unless outer sync operations are disabled.
- prefetch-data : Data prefetch. Value: <0> (forcibly disable), <1>
(forcibly enable), property absent (retain settings set by firmware)
- prefetch-instr : Instruction prefetch. Value: <0> (forcibly disable),
<1> (forcibly enable), property absent (retain settings set by
firmware)
- arm,dynamic-clock-gating : L2 dynamic clock gating. Value: <0> (forcibly
disable), <1> (forcibly enable), property absent (OS specific behavior,
preferably retain firmware settings)
- arm,standby-mode: L2 standby mode enable. Value <0> (forcibly disable),
<1> (forcibly enable), property absent (OS specific behavior,
preferably retain firmware settings)
- arm,early-bresp-disable : Disable the CA9 optimization Early BRESP (PL310)
- arm,full-line-zero-disable : Disable the CA9 optimization Full line of zero
write (PL310)
Example:
L2: cache-controller {
compatible = "arm,pl310-cache";
reg = <0xfff12000 0x1000>;
arm,data-latency = <1 1 1>;
arm,tag-latency = <2 2 2>;
arm,filter-ranges = <0x80000000 0x8000000>;
cache-unified;
cache-level = <2>;
interrupts = <45>;
};
Note 1: The description in this document doesn't apply to integrated L2
cache controllers as found in e.g. Cortex-A15/A7/A57/A53. These
integrated L2 controllers are assumed to be all preconfigured by
early secure boot code. Thus no need to deal with their configuration
in the kernel at all.
# SPDX-License-Identifier: GPL-2.0
%YAML 1.2
---
$id: http://devicetree.org/schemas/arm/l2c2x0.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#
title: ARM L2 Cache Controller
maintainers:
- Rob Herring <robh@kernel.org>
description: |+
ARM cores often have a separate L2C210/L2C220/L2C310 (also known as PL210/
PL220/PL310 and variants) based level 2 cache controller. All these various
implementations of the L2 cache controller have compatible programming
models (Note 1). Some of the properties that are just prefixed "cache-*" are
taken from section 3.7.3 of the Devicetree Specification which can be found
at:
https://www.devicetree.org/specifications/
Note 1: The description in this document doesn't apply to integrated L2
cache controllers as found in e.g. Cortex-A15/A7/A57/A53. These
integrated L2 controllers are assumed to be all preconfigured by
early secure boot code. Thus no need to deal with their configuration
in the kernel at all.
allOf:
- $ref: /schemas/cache-controller.yaml#
properties:
compatible:
enum:
- arm,pl310-cache
- arm,l220-cache
- arm,l210-cache
# DEPRECATED by "brcm,bcm11351-a2-pl310-cache"
- bcm,bcm11351-a2-pl310-cache
# For Broadcom bcm11351 chipset where an
# offset needs to be added to the address before passing down to the L2
# cache controller
- brcm,bcm11351-a2-pl310-cache
# Marvell Controller designed to be
# compatible with the ARM one, with system cache mode (meaning
# maintenance operations on L1 are broadcasted to the L2 and L2
# performs the same operation).
- marvell,aurora-system-cache
# Marvell Controller designed to be
# compatible with the ARM one with outer cache mode.
- marvell,aurora-outer-cache
# Marvell Tauros3 cache controller, compatible
# with arm,pl310-cache controller.
- marvell,tauros3-cache
cache-level:
const: 2
cache-unified: true
cache-size: true
cache-sets: true
cache-block-size: true
cache-line-size: true
reg:
maxItems: 1
arm,data-latency:
description: Cycles of latency for Data RAM accesses. Specifies 3 cells of
read, write and setup latencies. Minimum valid values are 1. Controllers
without setup latency control should use a value of 0.
allOf:
- $ref: /schemas/types.yaml#/definitions/uint32-array
- minItems: 2
maxItems: 3
items:
minimum: 0
maximum: 8
arm,tag-latency:
description: Cycles of latency for Tag RAM accesses. Specifies 3 cells of
read, write and setup latencies. Controllers without setup latency control
should use 0. Controllers without separate read and write Tag RAM latency
values should only use the first cell.
allOf:
- $ref: /schemas/types.yaml#/definitions/uint32-array
- minItems: 1
maxItems: 3
items:
minimum: 0
maximum: 8
arm,dirty-latency:
description: Cycles of latency for Dirty RAMs. This is a single cell.
allOf:
- $ref: /schemas/types.yaml#/definitions/uint32
- minimum: 1
maximum: 8
arm,filter-ranges:
description: <start length> Starting address and length of window to
filter. Addresses in the filter window are directed to the M1 port. Other
addresses will go to the M0 port.
allOf:
- $ref: /schemas/types.yaml#/definitions/uint32-array
- items:
minItems: 2
maxItems: 2
arm,io-coherent:
description: indicates that the system is operating in an hardware
I/O coherent mode. Valid only when the arm,pl310-cache compatible
string is used.
type: boolean
interrupts:
# Either a single combined interrupt or up to 9 individual interrupts
minItems: 1
maxItems: 9
cache-id-part:
description: cache id part number to be used if it is not present
on hardware
$ref: /schemas/types.yaml#/definitions/uint32
wt-override:
description: If present then L2 is forced to Write through mode
type: boolean
arm,double-linefill:
description: Override double linefill enable setting. Enable if
non-zero, disable if zero.
allOf:
- $ref: /schemas/types.yaml#/definitions/uint32
- enum: [ 0, 1 ]
arm,double-linefill-incr:
description: Override double linefill on INCR read. Enable
if non-zero, disable if zero.
allOf:
- $ref: /schemas/types.yaml#/definitions/uint32
- enum: [ 0, 1 ]
arm,double-linefill-wrap:
description: Override double linefill on WRAP read. Enable
if non-zero, disable if zero.
allOf:
- $ref: /schemas/types.yaml#/definitions/uint32
- enum: [ 0, 1 ]
arm,prefetch-drop:
description: Override prefetch drop enable setting. Enable if non-zero,
disable if zero.
allOf:
- $ref: /schemas/types.yaml#/definitions/uint32
- enum: [ 0, 1 ]
arm,prefetch-offset:
description: Override prefetch offset value.
allOf:
- $ref: /schemas/types.yaml#/definitions/uint32
- enum: [ 0, 1, 2, 3, 4, 5, 6, 7, 15, 23, 31 ]
arm,shared-override:
description: The default behavior of the L220 or PL310 cache
controllers with respect to the shareable attribute is to transform "normal
memory non-cacheable transactions" into "cacheable no allocate" (for reads)
or "write through no write allocate" (for writes).
On systems where this may cause DMA buffer corruption, this property must
be specified to indicate that such transforms are precluded.
type: boolean
arm,parity-enable:
description: enable parity checking on the L2 cache (L220 or PL310).
type: boolean
arm,parity-disable:
description: disable parity checking on the L2 cache (L220 or PL310).
type: boolean
arm,outer-sync-disable:
description: disable the outer sync operation on the L2 cache.
Some core tiles, especially ARM PB11MPCore have a faulty L220 cache that
will randomly hang unless outer sync operations are disabled.
type: boolean
prefetch-data:
description: |
Data prefetch. Value: <0> (forcibly disable), <1>
(forcibly enable), property absent (retain settings set by firmware)
allOf:
- $ref: /schemas/types.yaml#/definitions/uint32
- enum: [ 0, 1 ]
prefetch-instr:
description: |
Instruction prefetch. Value: <0> (forcibly disable),
<1> (forcibly enable), property absent (retain settings set by
firmware)
allOf:
- $ref: /schemas/types.yaml#/definitions/uint32
- enum: [ 0, 1 ]
arm,dynamic-clock-gating:
description: |
L2 dynamic clock gating. Value: <0> (forcibly
disable), <1> (forcibly enable), property absent (OS specific behavior,
preferably retain firmware settings)
allOf:
- $ref: /schemas/types.yaml#/definitions/uint32
- enum: [ 0, 1 ]
arm,standby-mode:
description: L2 standby mode enable. Value <0> (forcibly disable),
<1> (forcibly enable), property absent (OS specific behavior,
preferably retain firmware settings)
allOf:
- $ref: /schemas/types.yaml#/definitions/uint32
- enum: [ 0, 1 ]
arm,early-bresp-disable:
description: Disable the CA9 optimization Early BRESP (PL310)
type: boolean
arm,full-line-zero-disable:
description: Disable the CA9 optimization Full line of zero
write (PL310)
type: boolean
required:
- compatible
- cache-unified
- reg
additionalProperties: false
examples:
- |
cache-controller@fff12000 {
compatible = "arm,pl310-cache";
reg = <0xfff12000 0x1000>;
arm,data-latency = <1 1 1>;
arm,tag-latency = <2 2 2>;
arm,filter-ranges = <0x80000000 0x8000000>;
cache-unified;
cache-level = <2>;
interrupts = <45>;
};
...
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment