Commit a80a0bbe authored by Marc Zyngier's avatar Marc Zyngier Committed by Linus Torvalds

gpio: add interrupt handling capability to max732x

Most of the GPIO expanders supported by the max732x driver have interrupt
generation capability by reporting changes on input pins through an INT#
pin.  This patch implements the irq_chip functionnality (edge detection
only).
Signed-off-by: default avatarMarc Zyngier <maz@misterjones.org>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Jebediah Huang <jebediah.huang@gmail.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: default avatarAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: default avatarLinus Torvalds <torvalds@linux-foundation.org>
parent 0af62f4d
......@@ -139,6 +139,13 @@ config GPIO_MAX732X
Board setup code must specify the model to use, and the start
number for these GPIOs.
config GPIO_MAX732X_IRQ
bool "Interrupt controller support for MAX732x"
depends on GPIO_MAX732X=y && GENERIC_HARDIRQS
help
Say yes here to enable the max732x to be used as an interrupt
controller. It requires the driver to be built in the kernel.
config GPIO_PCA953X
tristate "PCA953x, PCA955x, TCA64xx, and MAX7310 I/O ports"
depends on I2C
......
......@@ -17,7 +17,8 @@
#include <linux/slab.h>
#include <linux/string.h>
#include <linux/gpio.h>
#include <linux/interrupt.h>
#include <linux/irq.h>
#include <linux/i2c.h>
#include <linux/i2c/max732x.h>
......@@ -31,7 +32,8 @@
* - Open Drain I/O
*
* designated by 'O', 'I' and 'P' individually according to MAXIM's
* datasheets.
* datasheets. 'I' and 'P' ports are interrupt capables, some with
* a dedicated interrupt mask.
*
* There are two groups of I/O ports, each group usually includes
* up to 8 I/O ports, and is accessed by a specific I2C address:
......@@ -44,7 +46,8 @@
*
* Within each group of ports, there are five known combinations of
* I/O ports: 4I4O, 4P4O, 8I, 8P, 8O, see the definitions below for
* the detailed organization of these ports.
* the detailed organization of these ports. Only Goup A is interrupt
* capable.
*
* GPIO numbers start from 'gpio_base + 0' to 'gpio_base + 8/16',
* and GPIOs from GROUP_A are numbered before those from GROUP_B
......@@ -68,16 +71,47 @@
#define GROUP_A(x) ((x) & 0xffff) /* I2C Addr: 0b'110xxxx */
#define GROUP_B(x) ((x) << 16) /* I2C Addr: 0b'101xxxx */
#define INT_NONE 0x0 /* No interrupt capability */
#define INT_NO_MASK 0x1 /* Has interrupts, no mask */
#define INT_INDEP_MASK 0x2 /* Has interrupts, independent mask */
#define INT_MERGED_MASK 0x3 /* Has interrupts, merged mask */
#define INT_CAPS(x) (((uint64_t)(x)) << 32)
enum {
MAX7319,
MAX7320,
MAX7321,
MAX7322,
MAX7323,
MAX7324,
MAX7325,
MAX7326,
MAX7327,
};
static uint64_t max732x_features[] = {
[MAX7319] = GROUP_A(IO_8I) | INT_CAPS(INT_MERGED_MASK),
[MAX7320] = GROUP_B(IO_8O),
[MAX7321] = GROUP_A(IO_8P) | INT_CAPS(INT_NO_MASK),
[MAX7322] = GROUP_A(IO_4I4O) | INT_CAPS(INT_MERGED_MASK),
[MAX7323] = GROUP_A(IO_4P4O) | INT_CAPS(INT_INDEP_MASK),
[MAX7324] = GROUP_A(IO_8I) | GROUP_B(IO_8O) | INT_CAPS(INT_MERGED_MASK),
[MAX7325] = GROUP_A(IO_8P) | GROUP_B(IO_8O) | INT_CAPS(INT_NO_MASK),
[MAX7326] = GROUP_A(IO_4I4O) | GROUP_B(IO_8O) | INT_CAPS(INT_MERGED_MASK),
[MAX7327] = GROUP_A(IO_4P4O) | GROUP_B(IO_8O) | INT_CAPS(INT_NO_MASK),
};
static const struct i2c_device_id max732x_id[] = {
{ "max7319", GROUP_A(IO_8I) },
{ "max7320", GROUP_B(IO_8O) },
{ "max7321", GROUP_A(IO_8P) },
{ "max7322", GROUP_A(IO_4I4O) },
{ "max7323", GROUP_A(IO_4P4O) },
{ "max7324", GROUP_A(IO_8I) | GROUP_B(IO_8O) },
{ "max7325", GROUP_A(IO_8P) | GROUP_B(IO_8O) },
{ "max7326", GROUP_A(IO_4I4O) | GROUP_B(IO_8O) },
{ "max7327", GROUP_A(IO_4P4O) | GROUP_B(IO_8O) },
{ "max7319", MAX7319 },
{ "max7320", MAX7320 },
{ "max7321", MAX7321 },
{ "max7322", MAX7322 },
{ "max7323", MAX7323 },
{ "max7324", MAX7324 },
{ "max7325", MAX7325 },
{ "max7326", MAX7326 },
{ "max7327", MAX7327 },
{ },
};
MODULE_DEVICE_TABLE(i2c, max732x_id);
......@@ -96,9 +130,19 @@ struct max732x_chip {
struct mutex lock;
uint8_t reg_out[2];
#ifdef CONFIG_GPIO_MAX732X_IRQ
struct mutex irq_lock;
int irq_base;
uint8_t irq_mask;
uint8_t irq_mask_cur;
uint8_t irq_trig_raise;
uint8_t irq_trig_fall;
uint8_t irq_features;
#endif
};
static int max732x_write(struct max732x_chip *chip, int group_a, uint8_t val)
static int max732x_writeb(struct max732x_chip *chip, int group_a, uint8_t val)
{
struct i2c_client *client;
int ret;
......@@ -113,7 +157,7 @@ static int max732x_write(struct max732x_chip *chip, int group_a, uint8_t val)
return 0;
}
static int max732x_read(struct max732x_chip *chip, int group_a, uint8_t *val)
static int max732x_readb(struct max732x_chip *chip, int group_a, uint8_t *val)
{
struct i2c_client *client;
int ret;
......@@ -142,7 +186,7 @@ static int max732x_gpio_get_value(struct gpio_chip *gc, unsigned off)
chip = container_of(gc, struct max732x_chip, gpio_chip);
ret = max732x_read(chip, is_group_a(chip, off), &reg_val);
ret = max732x_readb(chip, is_group_a(chip, off), &reg_val);
if (ret < 0)
return 0;
......@@ -162,7 +206,7 @@ static void max732x_gpio_set_value(struct gpio_chip *gc, unsigned off, int val)
reg_out = (off > 7) ? chip->reg_out[1] : chip->reg_out[0];
reg_out = (val) ? reg_out | mask : reg_out & ~mask;
ret = max732x_write(chip, is_group_a(chip, off), reg_out);
ret = max732x_writeb(chip, is_group_a(chip, off), reg_out);
if (ret < 0)
goto out;
......@@ -209,12 +253,278 @@ static int max732x_gpio_direction_output(struct gpio_chip *gc,
return 0;
}
#ifdef CONFIG_GPIO_MAX732X_IRQ
static int max732x_writew(struct max732x_chip *chip, uint16_t val)
{
int ret;
val = cpu_to_le16(val);
ret = i2c_master_send(chip->client_group_a, (char *)&val, 2);
if (ret < 0) {
dev_err(&chip->client_group_a->dev, "failed writing\n");
return ret;
}
return 0;
}
static int max732x_readw(struct max732x_chip *chip, uint16_t *val)
{
int ret;
ret = i2c_master_recv(chip->client_group_a, (char *)val, 2);
if (ret < 0) {
dev_err(&chip->client_group_a->dev, "failed reading\n");
return ret;
}
*val = le16_to_cpu(*val);
return 0;
}
static void max732x_irq_update_mask(struct max732x_chip *chip)
{
uint16_t msg;
if (chip->irq_mask == chip->irq_mask_cur)
return;
chip->irq_mask = chip->irq_mask_cur;
if (chip->irq_features == INT_NO_MASK)
return;
mutex_lock(&chip->lock);
switch (chip->irq_features) {
case INT_INDEP_MASK:
msg = (chip->irq_mask << 8) | chip->reg_out[0];
max732x_writew(chip, msg);
break;
case INT_MERGED_MASK:
msg = chip->irq_mask | chip->reg_out[0];
max732x_writeb(chip, 1, (uint8_t)msg);
break;
}
mutex_unlock(&chip->lock);
}
static int max732x_gpio_to_irq(struct gpio_chip *gc, unsigned off)
{
struct max732x_chip *chip;
chip = container_of(gc, struct max732x_chip, gpio_chip);
return chip->irq_base + off;
}
static void max732x_irq_mask(unsigned int irq)
{
struct max732x_chip *chip = get_irq_chip_data(irq);
chip->irq_mask_cur &= ~(1 << (irq - chip->irq_base));
}
static void max732x_irq_unmask(unsigned int irq)
{
struct max732x_chip *chip = get_irq_chip_data(irq);
chip->irq_mask_cur |= 1 << (irq - chip->irq_base);
}
static void max732x_irq_bus_lock(unsigned int irq)
{
struct max732x_chip *chip = get_irq_chip_data(irq);
mutex_lock(&chip->irq_lock);
chip->irq_mask_cur = chip->irq_mask;
}
static void max732x_irq_bus_sync_unlock(unsigned int irq)
{
struct max732x_chip *chip = get_irq_chip_data(irq);
max732x_irq_update_mask(chip);
mutex_unlock(&chip->irq_lock);
}
static int max732x_irq_set_type(unsigned int irq, unsigned int type)
{
struct max732x_chip *chip = get_irq_chip_data(irq);
uint16_t off = irq - chip->irq_base;
uint16_t mask = 1 << off;
if (!(mask & chip->dir_input)) {
dev_dbg(&chip->client->dev, "%s port %d is output only\n",
chip->client->name, off);
return -EACCES;
}
if (!(type & IRQ_TYPE_EDGE_BOTH)) {
dev_err(&chip->client->dev, "irq %d: unsupported type %d\n",
irq, type);
return -EINVAL;
}
if (type & IRQ_TYPE_EDGE_FALLING)
chip->irq_trig_fall |= mask;
else
chip->irq_trig_fall &= ~mask;
if (type & IRQ_TYPE_EDGE_RISING)
chip->irq_trig_raise |= mask;
else
chip->irq_trig_raise &= ~mask;
return max732x_gpio_direction_input(&chip->gpio_chip, off);
}
static struct irq_chip max732x_irq_chip = {
.name = "max732x",
.mask = max732x_irq_mask,
.unmask = max732x_irq_unmask,
.bus_lock = max732x_irq_bus_lock,
.bus_sync_unlock = max732x_irq_bus_sync_unlock,
.set_type = max732x_irq_set_type,
};
static uint8_t max732x_irq_pending(struct max732x_chip *chip)
{
uint8_t cur_stat;
uint8_t old_stat;
uint8_t trigger;
uint8_t pending;
uint16_t status;
int ret;
ret = max732x_readw(chip, &status);
if (ret)
return 0;
trigger = status >> 8;
trigger &= chip->irq_mask;
if (!trigger)
return 0;
cur_stat = status & 0xFF;
cur_stat &= chip->irq_mask;
old_stat = cur_stat ^ trigger;
pending = (old_stat & chip->irq_trig_fall) |
(cur_stat & chip->irq_trig_raise);
pending &= trigger;
return pending;
}
static irqreturn_t max732x_irq_handler(int irq, void *devid)
{
struct max732x_chip *chip = devid;
uint8_t pending;
uint8_t level;
pending = max732x_irq_pending(chip);
if (!pending)
return IRQ_HANDLED;
do {
level = __ffs(pending);
handle_nested_irq(level + chip->irq_base);
pending &= ~(1 << level);
} while (pending);
return IRQ_HANDLED;
}
static int max732x_irq_setup(struct max732x_chip *chip,
const struct i2c_device_id *id)
{
struct i2c_client *client = chip->client;
struct max732x_platform_data *pdata = client->dev.platform_data;
int has_irq = max732x_features[id->driver_data] >> 32;
int ret;
if (pdata->irq_base && has_irq != INT_NONE) {
int lvl;
chip->irq_base = pdata->irq_base;
chip->irq_features = has_irq;
mutex_init(&chip->irq_lock);
for (lvl = 0; lvl < chip->gpio_chip.ngpio; lvl++) {
int irq = lvl + chip->irq_base;
if (!(chip->dir_input & (1 << lvl)))
continue;
set_irq_chip_data(irq, chip);
set_irq_chip_and_handler(irq, &max732x_irq_chip,
handle_edge_irq);
set_irq_nested_thread(irq, 1);
#ifdef CONFIG_ARM
set_irq_flags(irq, IRQF_VALID);
#else
set_irq_noprobe(irq);
#endif
}
ret = request_threaded_irq(client->irq,
NULL,
max732x_irq_handler,
IRQF_TRIGGER_FALLING | IRQF_ONESHOT,
dev_name(&client->dev), chip);
if (ret) {
dev_err(&client->dev, "failed to request irq %d\n",
client->irq);
goto out_failed;
}
chip->gpio_chip.to_irq = max732x_gpio_to_irq;
}
return 0;
out_failed:
chip->irq_base = 0;
return ret;
}
static void max732x_irq_teardown(struct max732x_chip *chip)
{
if (chip->irq_base)
free_irq(chip->client->irq, chip);
}
#else /* CONFIG_GPIO_MAX732X_IRQ */
static int max732x_irq_setup(struct max732x_chip *chip,
const struct i2c_device_id *id)
{
struct i2c_client *client = chip->client;
struct max732x_platform_data *pdata = client->dev.platform_data;
int has_irq = max732x_features[id->driver_data] >> 32;
if (pdata->irq_base && has_irq != INT_NONE)
dev_warn(&client->dev, "interrupt support not compiled in\n");
return 0;
}
static void max732x_irq_teardown(struct max732x_chip *chip)
{
}
#endif
static int __devinit max732x_setup_gpio(struct max732x_chip *chip,
const struct i2c_device_id *id,
unsigned gpio_start)
{
struct gpio_chip *gc = &chip->gpio_chip;
uint32_t id_data = id->driver_data;
uint32_t id_data = (uint32_t)max732x_features[id->driver_data];
int i, port = 0;
for (i = 0; i < 16; i++, id_data >>= 2) {
......@@ -306,9 +616,13 @@ static int __devinit max732x_probe(struct i2c_client *client,
mutex_init(&chip->lock);
max732x_read(chip, is_group_a(chip, 0), &chip->reg_out[0]);
max732x_readb(chip, is_group_a(chip, 0), &chip->reg_out[0]);
if (nr_port > 7)
max732x_read(chip, is_group_a(chip, 8), &chip->reg_out[1]);
max732x_readb(chip, is_group_a(chip, 8), &chip->reg_out[1]);
ret = max732x_irq_setup(chip, id);
if (ret)
goto out_failed;
ret = gpiochip_add(&chip->gpio_chip);
if (ret)
......@@ -325,6 +639,7 @@ static int __devinit max732x_probe(struct i2c_client *client,
return 0;
out_failed:
max732x_irq_teardown(chip);
kfree(chip);
return ret;
}
......@@ -352,6 +667,8 @@ static int __devexit max732x_remove(struct i2c_client *client)
return ret;
}
max732x_irq_teardown(chip);
/* unregister any dummy i2c_client */
if (chip->client_dummy)
i2c_unregister_device(chip->client_dummy);
......
......@@ -7,6 +7,9 @@ struct max732x_platform_data {
/* number of the first GPIO */
unsigned gpio_base;
/* interrupt base */
int irq_base;
void *context; /* param to setup/teardown */
int (*setup)(struct i2c_client *client,
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment