ARM: dts: armada388-clearfog: move I2C nodes

Move the I2C nodes over to use the label form to reference the I2C
controllers, rather than replicating the device node path.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>

arch/arm/boot/dts/armada-388-clearfog.dtsi

@@ -92,7 +92,62 @@ fixed-link {
 				};
 			};
 
-			i2c@11000 {
+			sata@a8000 {
+				/* pinctrl? */
+				status = "okay";
+			};
+
+			sata@e0000 {
+				/* pinctrl? */
+				status = "okay";
+			};
+
+			sdhci@d8000 {
+				bus-width = <4>;
+				cd-gpios = <&gpio0 20 GPIO_ACTIVE_LOW>;
+				no-1-8-v;
+				pinctrl-0 = <&microsom_sdhci_pins
+					     &clearfog_sdhci_cd_pins>;
+				pinctrl-names = "default";
+				status = "okay";
+				vmmc = <&reg_3p3v>;
+				wp-inverted;
+			};
+
+			serial@12100 {
+				/* mikrobus uart */
+				pinctrl-0 = <&mikro_uart_pins>;
+				pinctrl-names = "default";
+				status = "okay";
+			};
+
+			usb@58000 {
+				/* CON3, nearest  power. */
+				status = "okay";
+			};
+
+			usb3@f8000 {
+				/* CON7 */
+				status = "okay";
+			};
+		};
+
+		pcie-controller {
+			status = "okay";
+			/*
+			 * The two PCIe units are accessible through
+			 * the mini-PCIe connectors on the board.
+			 */
+			pcie@2,0 {
+				/* Port 1, Lane 0. CON3, nearest power. */
+				reset-gpios = <&expander0 1 GPIO_ACTIVE_LOW>;
+				status = "okay";
+			};
+		};
+	};
+};
+
+&i2c0 {
 	/* Is there anything on this? */
 	clock-frequency = <100000>;
 	pinctrl-0 = <&i2c0_pins>;
@@ -121,10 +176,8 @@ i2c@11000 {
 	expander0: gpio-expander@20 {
 		/*
 		 * This is how it should be:
-					 * compatible = "onnn,pca9655",
-					 *	 "nxp,pca9555";
-					 * but you can't do this because of
-					 * the way I2C works.
+		 * compatible = "onnn,pca9655", "nxp,pca9555";
+		 * but you can't do this because of the way I2C works.
 		 */
 		compatible = "nxp,pca9555";
 		gpio-controller;
@@ -198,78 +251,20 @@ mikrobus_adc: mcp3021@4c {
 	};
 
 	/* Also something at 0x64 */
-			};
+};
 
-			i2c@11100 {
+&i2c1 {
 	/*
 	 * Routed to SFP, mikrobus, and PCIe.
-				 * SFP limits this to 100kHz, and requires
-				 *  an AT24C01A/02/04 with address pins tied
-				 *  low, which takes addresses 0x50 and 0x51.
-				 * Mikrobus doesn't specify beyond an I2C
-				 *  bus being present.
-				 * PCIe uses ARP to assign addresses, or
-				 *  0x63-0x64.
+	 * SFP limits this to 100kHz, and requires an AT24C01A/02/04 with
+	 *  address pins tied low, which takes addresses 0x50 and 0x51.
+	 * Mikrobus doesn't specify beyond an I2C bus being present.
+	 * PCIe uses ARP to assign addresses, or 0x63-0x64.
 	 */
 	clock-frequency = <100000>;
 	pinctrl-0 = <&clearfog_i2c1_pins>;
 	pinctrl-names = "default";
 	status = "okay";
-			};
-
-			sata@a8000 {
-				/* pinctrl? */
-				status = "okay";
-			};
-
-			sata@e0000 {
-				/* pinctrl? */
-				status = "okay";
-			};
-
-			sdhci@d8000 {
-				bus-width = <4>;
-				cd-gpios = <&gpio0 20 GPIO_ACTIVE_LOW>;
-				no-1-8-v;
-				pinctrl-0 = <&microsom_sdhci_pins
-					     &clearfog_sdhci_cd_pins>;
-				pinctrl-names = "default";
-				status = "okay";
-				vmmc = <&reg_3p3v>;
-				wp-inverted;
-			};
-
-			serial@12100 {
-				/* mikrobus uart */
-				pinctrl-0 = <&mikro_uart_pins>;
-				pinctrl-names = "default";
-				status = "okay";
-			};
-
-			usb@58000 {
-				/* CON3, nearest  power. */
-				status = "okay";
-			};
-
-			usb3@f8000 {
-				/* CON7 */
-				status = "okay";
-			};
-		};
-
-		pcie-controller {
-			status = "okay";
-			/*
-			 * The two PCIe units are accessible through
-			 * the mini-PCIe connectors on the board.
-			 */
-			pcie@2,0 {
-				/* Port 1, Lane 0. CON3, nearest power. */
-				reset-gpios = <&expander0 1 GPIO_ACTIVE_LOW>;
-				status = "okay";
-			};
-		};
-	};
 };
 
 &pinctrl {