ath9k: use correct OTP register offsets for AR9550

Accessing the OTP memory on AR9950 causes a data bus
like this:

  Data bus error, epc == 801f7774, ra == 801f7774
  Oops[#1]:
  CPU: 0 PID: 1 Comm: swapper Not tainted 3.10.0-rc3 #592
  task: 87c28000 ti: 87c22000 task.ti: 87c22000
  $ 0   : 00000000 00000061 deadc0de 00000000
  $ 4   : b8115f18 00015f18 00000007 00000004
  $ 8   : 00000001 7c7c3c7c 7c7c7c7c 7c7c7c7c
  $12   : 7c7c3c7c 80320a68 00000000 7c7c7c3c
  $16   : 87cd8010 00015f18 00000007 00000000
  $20   : 00000064 00000004 87c23c7c 8035210c
  $24   : 00000000 801f3674
  $28   : 87c22000 87c23b48 00000001 801f7774
  Hi    : 00000000
  Lo    : 00000064
  epc   : 801f7774 ath9k_hw_wait+0x58/0xb0
      Not tainted
  ra    : 801f7774 ath9k_hw_wait+0x58/0xb0
  Status: 1000cc03 KERNEL EXL IE
  Cause : 4080801c
  PrId  : 00019750 (MIPS 74Kc)
  Modules linked in:
  Process swapper (pid: 1, threadinfo=87c22000, task=87c28000, ts=00000000)
  Stack : 0000000f 00000061 00002710 8006240c 00000001 87cd8010 87c23bb0 87cd8010
          00000000 00000004 00000003 80210c7c 000000b3 67fa8000 0000032a 000006fe
          000003e8 00000002 00000028 87c23bf0 000003ff 80210d24 803e5630 80210e28
          00000000 00000007 87cd8010 00007044 00000004 00000061 000003ff 000001ff
          87c26000 87cd8010 00000220 87cd8bb8 80210000 8020fcf4 87c22000 87c23c08
          ...
  Call Trace:
  [<801f7774>] ath9k_hw_wait+0x58/0xb0
  [<80210c7c>] ar9300_otp_read_word+0x80/0xd4
  [<80210d24>] ar9300_read_otp+0x54/0xb0
  [<8020fcf4>] ar9300_check_eeprom_header+0x1c/0x40
  [<80210fe4>] ath9k_hw_ar9300_fill_eeprom+0x118/0x39c
  [<80206650>] ath9k_hw_eeprom_init+0x74/0xb4
  [<801f96d0>] ath9k_hw_init+0x7ec/0x96c
  [<801e65ec>] ath9k_init_device+0x340/0x758
  [<801f35d0>] ath_ahb_probe+0x21c/0x2c0
  [<801c041c>] driver_probe_device+0xc0/0x1e4
  [<801c05ac>] __driver_attach+0x6c/0xa4
  [<801bea08>] bus_for_each_dev+0x64/0xa8
  [<801bfa40>] bus_add_driver+0xcc/0x24c
  [<801c0954>] driver_register+0xbc/0x17c
  [<803f8fc0>] ath9k_init+0x5c/0x88
  [<800608fc>] do_one_initcall+0xec/0x1a0
  [<803e6a68>] kernel_init_freeable+0x13c/0x200
  [<80309cdc>] kernel_init+0x1c/0xe4
  [<80062450>] ret_from_kernel_thread+0x10/0x18

On the AR9550, the OTP registers are located at
the same address as on the AR9340. Use the correct
values to avoid the error.

Cc: stable@vger.kernel.org  # 3.6+
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

drivers/net/wireless/ath/ath9k/ar9003_eeprom.h

@@ -68,13 +68,16 @@
 #define AR9300_BASE_ADDR 0x3ff
 #define AR9300_BASE_ADDR_512 0x1ff
 
-#define AR9300_OTP_BASE			(AR_SREV_9340(ah) ? 0x30000 : 0x14000)
-#define AR9300_OTP_STATUS		(AR_SREV_9340(ah) ? 0x30018 : 0x15f18)
+#define AR9300_OTP_BASE \
+		((AR_SREV_9340(ah) || AR_SREV_9550(ah)) ? 0x30000 : 0x14000)
+#define AR9300_OTP_STATUS \
+		((AR_SREV_9340(ah) || AR_SREV_9550(ah)) ? 0x30018 : 0x15f18)
 #define AR9300_OTP_STATUS_TYPE		0x7
 #define AR9300_OTP_STATUS_VALID		0x4
 #define AR9300_OTP_STATUS_ACCESS_BUSY	0x2
 #define AR9300_OTP_STATUS_SM_BUSY	0x1
-#define AR9300_OTP_READ_DATA		(AR_SREV_9340(ah) ? 0x3001c : 0x15f1c)
+#define AR9300_OTP_READ_DATA \
+		((AR_SREV_9340(ah) || AR_SREV_9550(ah)) ? 0x3001c : 0x15f1c)
 
 enum targetPowerHTRates {
 	HT_TARGET_RATE_0_8_16,