Merge branch 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging

* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
  hwmon: (sysfs-interface) Update tempX_type attribute to be more generic
  hwmon: (adm1031) Fix coding style issues
  hwmon: (it87) Add IT8728F support
  hwmon: (coretemp) Add missing section annotations
  hwmon: (lm90) Add range check to set_update_interval
  hwmon: (lm63) Support extended lookup table of LM96163
  hwmon: (lm63) Expose automatic fan speed control lookup table
  hwmon: (lm63) Fix incorrect comment about I2C address
  hwmon: (lm63) LM64 has a dedicated pin for tachometer
  hwmon: (lm63) Add sensor type attribute for external sensor on LM96163
  hwmon: (lm63) Add support for update_interval sysfs attribute
  hwmon: (lm63) Add support for writing the external critical temperature
  hwmon: (lm63) Add support for unsigned upper temperature limits
  hwmon: (lm63) Add support for LM96163
  hwmon: (lm63) Add support for external temperature offset register
  hwmon: (lm63) Fix checkpatch errors
  hwmon: (max1111) Change sysfs interface to in[0-3]_input in millivolts

Documentation/hwmon/it87

@@ -26,6 +26,10 @@ Supported chips:
     Prefix: 'it8721'
     Addresses scanned: from Super I/O config space (8 I/O ports)
     Datasheet: Not publicly available
+  * IT8728F
+    Prefix: 'it8728'
+    Addresses scanned: from Super I/O config space (8 I/O ports)
+    Datasheet: Not publicly available
   * SiS950   [clone of IT8705F]
     Prefix: 'it87'
     Addresses scanned: from Super I/O config space (8 I/O ports)
@@ -71,7 +75,7 @@ Description
 -----------
 
 This driver implements support for the IT8705F, IT8712F, IT8716F,
-IT8718F, IT8720F, IT8721F, IT8726F, IT8758E and SiS950 chips.
+IT8718F, IT8720F, IT8721F, IT8726F, IT8728F, IT8758E and SiS950 chips.
 
 These chips are 'Super I/O chips', supporting floppy disks, infrared ports,
 joysticks and other miscellaneous stuff. For hardware monitoring, they
@@ -105,6 +109,9 @@ The IT8726F is just bit enhanced IT8716F with additional hardware
 for AMD power sequencing. Therefore the chip will appear as IT8716F
 to userspace applications.
 
+The IT8728F is considered compatible with the IT8721F, until a datasheet
+becomes available (hopefully.)
+
 Temperatures are measured in degrees Celsius. An alarm is triggered once
 when the Overtemperature Shutdown limit is crossed.
 
@@ -121,8 +128,8 @@ alarm is triggered if the voltage has crossed a programmable minimum or
 maximum limit. Note that minimum in this case always means 'closest to
 zero'; this is important for negative voltage measurements. All voltage
 inputs can measure voltages between 0 and 4.08 volts, with a resolution of
-0.016 volt (except IT8721F/IT8758E: 0.012 volt.) The battery voltage in8 does
-not have limit registers.
+0.016 volt (except IT8721F/IT8758E and IT8728F: 0.012 volt.) The battery
+voltage in8 does not have limit registers.
 
 On the IT8721F/IT8758E, some voltage inputs are internal and scaled inside
 the chip (in7, in8 and optionally in3). The driver handles this transparently

Documentation/hwmon/lm63

@@ -12,6 +12,11 @@ Supported chips:
     Addresses scanned: I2C 0x18 and 0x4e
     Datasheet: Publicly available at the National Semiconductor website
                http://www.national.com/pf/LM/LM64.html
+  * National Semiconductor LM96163
+    Prefix: 'lm96163'
+    Addresses scanned: I2C 0x4c
+    Datasheet: Publicly available at the National Semiconductor website
+               http://www.national.com/pf/LM/LM96163.html
 
 Author: Jean Delvare <khali@linux-fr.org>
 
@@ -49,16 +54,24 @@ value for measuring the speed of the fan. It can measure fan speeds down to
 Note that the pin used for fan monitoring is shared with an alert out
 function. Depending on how the board designer wanted to use the chip, fan
 speed monitoring will or will not be possible. The proper chip configuration
-is left to the BIOS, and the driver will blindly trust it.
+is left to the BIOS, and the driver will blindly trust it. Only the original
+LM63 suffers from this limitation, the LM64 and LM96163 have separate pins
+for fan monitoring and alert out. On the LM64, monitoring is always enabled;
+on the LM96163 it can be disabled.
 
 A PWM output can be used to control the speed of the fan. The LM63 has two
 PWM modes: manual and automatic. Automatic mode is not fully implemented yet
 (you cannot define your custom PWM/temperature curve), and mode change isn't
 supported either.
 
-The lm63 driver will not update its values more frequently than every
-second; reading them more often will do no harm, but will return 'old'
-values.
+The lm63 driver will not update its values more frequently than configured with
+the update_interval sysfs attribute; reading them more often will do no harm,
+but will return 'old' values. Values in the automatic fan control lookup table
+(attributes pwm1_auto_*) have their own independent lifetime of 5 seconds.
 
 The LM64 is effectively an LM63 with GPIO lines. The driver does not
 support these GPIO lines at present.
+
+The LM96163 is an enhanced version of LM63 with improved temperature accuracy
+and better PWM resolution. For LM96163, the external temperature sensor type is
+configurable as CPU embedded diode(1) or 3904 transistor(2).

Documentation/hwmon/sysfs-interface

@@ -304,7 +304,7 @@ value (fastest fan speed) wins.
 temp[1-*]_type	Sensor type selection.
 		Integers 1 to 6
 		RW
-		1: PII/Celeron Diode
+		1: CPU embedded diode
 		2: 3904 transistor
 		3: thermal diode
 		4: thermistor

drivers/hwmon/Kconfig

@@ -474,8 +474,8 @@ config SENSORS_IT87
 	select HWMON_VID
 	help
 	  If you say yes here you get support for ITE IT8705F, IT8712F,
-	  IT8716F, IT8718F, IT8720F, IT8721F, IT8726F and IT8758E sensor
-	  chips, and the SiS960 clone.
+	  IT8716F, IT8718F, IT8720F, IT8721F, IT8726F, IT8728F and IT8758E
+	  sensor chips, and the SiS960 clone.
 
 	  This driver can also be built as a module.  If so, the module
 	  will be called it87.
@@ -515,11 +515,11 @@ config SENSORS_LINEAGE
 	  will be called lineage-pem.
 
 config SENSORS_LM63
-	tristate "National Semiconductor LM63 and LM64"
+	tristate "National Semiconductor LM63 and compatibles"
 	depends on I2C
 	help
 	  If you say yes here you get support for the National
-	  Semiconductor LM63 and LM64 remote diode digital temperature
+	  Semiconductor LM63, LM64, and LM96163 remote diode digital temperature
 	  sensors with integrated fan control.  Such chips are found
 	  on the Tyan S4882 (Thunder K8QS Pro) motherboard, among
 	  others.

drivers/hwmon/adm1031.c

@@ -155,7 +155,8 @@ adm1031_write_value(struct i2c_client *client, u8 reg, unsigned int value)
 #define TEMP_OFFSET_FROM_REG(val)	TEMP_FROM_REG((val) < 0 ? \
 						      (val) | 0x70 : (val))
 
-#define FAN_FROM_REG(reg, div)		((reg) ? (11250 * 60) / ((reg) * (div)) : 0)
+#define FAN_FROM_REG(reg, div)		((reg) ? \
+					 (11250 * 60) / ((reg) * (div)) : 0)
 
 static int FAN_TO_REG(int reg, int div)
 {
@@ -174,8 +175,8 @@ static int FAN_TO_REG(int reg, int div)
 	(((reg) & 0x1F) | (((val) << 5) & 0xe0))
 
 #define AUTO_TEMP_MIN_TO_REG(val, reg)	\
-	((((val)/500) & 0xf8)|((reg) & 0x7))
-#define AUTO_TEMP_RANGE_FROM_REG(reg)	(5000 * (1<< ((reg)&0x7)))
+	((((val) / 500) & 0xf8) | ((reg) & 0x7))
+#define AUTO_TEMP_RANGE_FROM_REG(reg)	(5000 * (1 << ((reg) & 0x7)))
 #define AUTO_TEMP_MIN_FROM_REG(reg)	(1000 * ((((reg) >> 3) & 0x1f) << 2))
 
 #define AUTO_TEMP_MIN_FROM_REG_DEG(reg)	((((reg) >> 3) & 0x1f) << 2)
@@ -202,7 +203,7 @@ static int AUTO_TEMP_MAX_TO_REG(int val, int reg, int pwm)
 
 /* FAN auto control */
 #define GET_FAN_AUTO_BITFIELD(data, idx)	\
-	(*(data)->chan_select_table)[FAN_CHAN_FROM_REG((data)->conf1)][idx%2]
+	(*(data)->chan_select_table)[FAN_CHAN_FROM_REG((data)->conf1)][idx % 2]
 
 /* The tables below contains the possible values for the auto fan
  * control bitfields. the index in the table is the register value.
@@ -230,7 +231,7 @@ static const auto_chan_table_t auto_channel_select_table_adm1030 = {
  */
 static int
 get_fan_auto_nearest(struct adm1031_data *data,
-		     int chan, u8 val, u8 reg, u8 * new_reg)
+		     int chan, u8 val, u8 reg, u8 *new_reg)
 {
 	int i;
 	int first_match = -1, exact_match = -1;
@@ -258,13 +259,13 @@ get_fan_auto_nearest(struct adm1031_data *data,
 		}
 	}
 
-	if (exact_match >= 0) {
+	if (exact_match >= 0)
 		*new_reg = exact_match;
-	} else if (first_match >= 0) {
+	else if (first_match >= 0)
 		*new_reg = first_match;
-	} else {
+	else
 		return -EINVAL;
-	}
+
 	return 0;
 }
 
@@ -283,23 +284,28 @@ set_fan_auto_channel(struct device *dev, struct device_attribute *attr,
 	struct i2c_client *client = to_i2c_client(dev);
 	struct adm1031_data *data = i2c_get_clientdata(client);
 	int nr = to_sensor_dev_attr(attr)->index;
-	int val = simple_strtol(buf, NULL, 10);
+	long val;
 	u8 reg;
 	int ret;
 	u8 old_fan_mode;
 
+	ret = kstrtol(buf, 10, &val);
+	if (ret)
+		return ret;
+
 	old_fan_mode = data->conf1;
 
 	mutex_lock(&data->update_lock);
 
-	if ((ret = get_fan_auto_nearest(data, nr, val, data->conf1, &reg))) {
+	ret = get_fan_auto_nearest(data, nr, val, data->conf1, &reg);
+	if (ret) {
 		mutex_unlock(&data->update_lock);
 		return ret;
 	}
 	data->conf1 = FAN_CHAN_TO_REG(reg, data->conf1);
 	if ((data->conf1 & ADM1031_CONF1_AUTO_MODE) ^
 	    (old_fan_mode & ADM1031_CONF1_AUTO_MODE)) {
-		if (data->conf1 & ADM1031_CONF1_AUTO_MODE){
+		if (data->conf1 & ADM1031_CONF1_AUTO_MODE) {
 			/* Switch to Auto Fan Mode
 			 * Save PWM registers
 			 * Set PWM registers to 33% Both */
@@ -350,7 +356,12 @@ set_auto_temp_min(struct device *dev, struct device_attribute *attr,
 	struct i2c_client *client = to_i2c_client(dev);
 	struct adm1031_data *data = i2c_get_clientdata(client);
 	int nr = to_sensor_dev_attr(attr)->index;
-	int val = simple_strtol(buf, NULL, 10);
+	long val;
+	int ret;
+
+	ret = kstrtol(buf, 10, &val);
+	if (ret)
+		return ret;
 
 	mutex_lock(&data->update_lock);
 	data->auto_temp[nr] = AUTO_TEMP_MIN_TO_REG(val, data->auto_temp[nr]);
@@ -374,10 +385,16 @@ set_auto_temp_max(struct device *dev, struct device_attribute *attr,
 	struct i2c_client *client = to_i2c_client(dev);
 	struct adm1031_data *data = i2c_get_clientdata(client);
 	int nr = to_sensor_dev_attr(attr)->index;
-	int val = simple_strtol(buf, NULL, 10);
+	long val;
+	int ret;
+
+	ret = kstrtol(buf, 10, &val);
+	if (ret)
+		return ret;
 
 	mutex_lock(&data->update_lock);
-	data->temp_max[nr] = AUTO_TEMP_MAX_TO_REG(val, data->auto_temp[nr], data->pwm[nr]);
+	data->temp_max[nr] = AUTO_TEMP_MAX_TO_REG(val, data->auto_temp[nr],
+						  data->pwm[nr]);
 	adm1031_write_value(client, ADM1031_REG_AUTO_TEMP(nr),
 			    data->temp_max[nr]);
 	mutex_unlock(&data->update_lock);
@@ -410,8 +427,12 @@ static ssize_t set_pwm(struct device *dev, struct device_attribute *attr,
 	struct i2c_client *client = to_i2c_client(dev);
 	struct adm1031_data *data = i2c_get_clientdata(client);
 	int nr = to_sensor_dev_attr(attr)->index;
-	int val = simple_strtol(buf, NULL, 10);
-	int reg;
+	long val;
+	int ret, reg;
+
+	ret = kstrtol(buf, 10, &val);
+	if (ret)
+		return ret;
 
 	mutex_lock(&data->update_lock);
 	if ((data->conf1 & ADM1031_CONF1_AUTO_MODE) &&
@@ -449,7 +470,11 @@ static int trust_fan_readings(struct adm1031_data *data, int chan)
 
 	if (data->conf1 & ADM1031_CONF1_AUTO_MODE) {
 		switch (data->conf1 & 0x60) {
-		case 0x00:	/* remote temp1 controls fan1 remote temp2 controls fan2 */
+		case 0x00:
+			/*
+			 * remote temp1 controls fan1,
+			 * remote temp2 controls fan2
+			 */
 			res = data->temp[chan+1] >=
 			    AUTO_TEMP_MIN_FROM_REG_DEG(data->auto_temp[chan+1]);
 			break;
@@ -515,7 +540,12 @@ static ssize_t set_fan_min(struct device *dev, struct device_attribute *attr,
 	struct i2c_client *client = to_i2c_client(dev);
 	struct adm1031_data *data = i2c_get_clientdata(client);
 	int nr = to_sensor_dev_attr(attr)->index;
-	int val = simple_strtol(buf, NULL, 10);
+	long val;
+	int ret;
+
+	ret = kstrtol(buf, 10, &val);
+	if (ret)
+		return ret;
 
 	mutex_lock(&data->update_lock);
 	if (val) {
@@ -534,10 +564,15 @@ static ssize_t set_fan_div(struct device *dev, struct device_attribute *attr,
 	struct i2c_client *client = to_i2c_client(dev);
 	struct adm1031_data *data = i2c_get_clientdata(client);
 	int nr = to_sensor_dev_attr(attr)->index;
-	int val = simple_strtol(buf, NULL, 10);
+	long val;
 	u8 tmp;
 	int old_div;
 	int new_min;
+	int ret;
+
+	ret = kstrtol(buf, 10, &val);
+	if (ret)
+		return ret;
 
 	tmp = val == 8 ? 0xc0 :
 	      val == 4 ? 0x80 :
@@ -631,9 +666,13 @@ static ssize_t set_temp_offset(struct device *dev,
 	struct i2c_client *client = to_i2c_client(dev);
 	struct adm1031_data *data = i2c_get_clientdata(client);
 	int nr = to_sensor_dev_attr(attr)->index;
-	int val;
+	long val;
+	int ret;
+
+	ret = kstrtol(buf, 10, &val);
+	if (ret)
+		return ret;
 
-	val = simple_strtol(buf, NULL, 10);
 	val = SENSORS_LIMIT(val, -15000, 15000);
 	mutex_lock(&data->update_lock);
 	data->temp_offset[nr] = TEMP_OFFSET_TO_REG(val);
@@ -648,9 +687,13 @@ static ssize_t set_temp_min(struct device *dev, struct device_attribute *attr,
 	struct i2c_client *client = to_i2c_client(dev);
 	struct adm1031_data *data = i2c_get_clientdata(client);
 	int nr = to_sensor_dev_attr(attr)->index;
-	int val;
+	long val;
+	int ret;
+
+	ret = kstrtol(buf, 10, &val);
+	if (ret)
+		return ret;
 
-	val = simple_strtol(buf, NULL, 10);
 	val = SENSORS_LIMIT(val, -55000, nr == 0 ? 127750 : 127875);
 	mutex_lock(&data->update_lock);
 	data->temp_min[nr] = TEMP_TO_REG(val);
@@ -665,9 +708,13 @@ static ssize_t set_temp_max(struct device *dev, struct device_attribute *attr,
 	struct i2c_client *client = to_i2c_client(dev);
 	struct adm1031_data *data = i2c_get_clientdata(client);
 	int nr = to_sensor_dev_attr(attr)->index;
-	int val;
+	long val;
+	int ret;
+
+	ret = kstrtol(buf, 10, &val);
+	if (ret)
+		return ret;
 
-	val = simple_strtol(buf, NULL, 10);
 	val = SENSORS_LIMIT(val, -55000, nr == 0 ? 127750 : 127875);
 	mutex_lock(&data->update_lock);
 	data->temp_max[nr] = TEMP_TO_REG(val);
@@ -682,9 +729,13 @@ static ssize_t set_temp_crit(struct device *dev, struct device_attribute *attr,
 	struct i2c_client *client = to_i2c_client(dev);
 	struct adm1031_data *data = i2c_get_clientdata(client);
 	int nr = to_sensor_dev_attr(attr)->index;
-	int val;
+	long val;
+	int ret;
+
+	ret = kstrtol(buf, 10, &val);
+	if (ret)
+		return ret;
 
-	val = simple_strtol(buf, NULL, 10);
 	val = SENSORS_LIMIT(val, -55000, nr == 0 ? 127750 : 127875);
 	mutex_lock(&data->update_lock);
 	data->temp_crit[nr] = TEMP_TO_REG(val);
@@ -711,7 +762,8 @@ temp_reg(2);
 temp_reg(3);
 
 /* Alarms */
-static ssize_t show_alarms(struct device *dev, struct device_attribute *attr, char *buf)
+static ssize_t show_alarms(struct device *dev, struct device_attribute *attr,
+			   char *buf)
 {
 	struct adm1031_data *data = adm1031_update_device(dev);
 	return sprintf(buf, "%d\n", data->alarm);
@@ -919,12 +971,13 @@ static int adm1031_probe(struct i2c_client *client,
 	adm1031_init_client(client);
 
 	/* Register sysfs hooks */
-	if ((err = sysfs_create_group(&client->dev.kobj, &adm1031_group)))
+	err = sysfs_create_group(&client->dev.kobj, &adm1031_group);
+	if (err)
 		goto exit_free;
 
 	if (data->chip_type == adm1031) {
-		if ((err = sysfs_create_group(&client->dev.kobj,
-						&adm1031_group_opt)))
+		err = sysfs_create_group(&client->dev.kobj, &adm1031_group_opt);
+		if (err)
 			goto exit_remove;
 	}
 
@@ -970,14 +1023,13 @@ static void adm1031_init_client(struct i2c_client *client)
 	}
 	/* Initialize the ADM1031 chip (enables fan speed reading ) */
 	read_val = adm1031_read_value(client, ADM1031_REG_CONF2);
-	if ((read_val | mask) != read_val) {
+	if ((read_val | mask) != read_val)
 		adm1031_write_value(client, ADM1031_REG_CONF2, read_val | mask);
-	}
 
 	read_val = adm1031_read_value(client, ADM1031_REG_CONF1);
 	if ((read_val | ADM1031_CONF1_MONITOR_ENABLE) != read_val) {
-	    adm1031_write_value(client, ADM1031_REG_CONF1, read_val |
-				ADM1031_CONF1_MONITOR_ENABLE);
+		adm1031_write_value(client, ADM1031_REG_CONF1,
+				    read_val | ADM1031_CONF1_MONITOR_ENABLE);
 	}
 
 	/* Read the chip's update rate */
@@ -1024,8 +1076,7 @@ static struct adm1031_data *adm1031_update_device(struct device *dev)
 				/* oldh is actually newer */
 				if (newh != oldh)
 					dev_warn(&client->dev,
-						 "Remote temperature may be "
-						 "wrong.\n");
+					  "Remote temperature may be wrong.\n");
 #endif
 			}
 			data->temp[chan] = newh;
@@ -1052,22 +1103,24 @@ static struct adm1031_data *adm1031_update_device(struct device *dev)
 		data->conf2 = adm1031_read_value(client, ADM1031_REG_CONF2);
 
 		data->alarm = adm1031_read_value(client, ADM1031_REG_STATUS(0))
-			     | (adm1031_read_value(client, ADM1031_REG_STATUS(1))
-				<< 8);
-		if (data->chip_type == adm1030) {
+		    | (adm1031_read_value(client, ADM1031_REG_STATUS(1)) << 8);
+		if (data->chip_type == adm1030)
 			data->alarm &= 0xc0ff;
-		}
 
-		for (chan=0; chan<(data->chip_type == adm1030 ? 1 : 2); chan++) {
+		for (chan = 0; chan < (data->chip_type == adm1030 ? 1 : 2);
+		     chan++) {
 			data->fan_div[chan] =
-			    adm1031_read_value(client, ADM1031_REG_FAN_DIV(chan));
+			    adm1031_read_value(client,
+					       ADM1031_REG_FAN_DIV(chan));
 			data->fan_min[chan] =
-			    adm1031_read_value(client, ADM1031_REG_FAN_MIN(chan));
+			    adm1031_read_value(client,
+					       ADM1031_REG_FAN_MIN(chan));
 			data->fan[chan] =
-			    adm1031_read_value(client, ADM1031_REG_FAN_SPEED(chan));
+			    adm1031_read_value(client,
+					       ADM1031_REG_FAN_SPEED(chan));
 			data->pwm[chan] =
-			    0xf & (adm1031_read_value(client, ADM1031_REG_PWM) >>
-				   (4*chan));
+			  (adm1031_read_value(client,
+					ADM1031_REG_PWM) >> (4 * chan)) & 0x0f;
 		}
 		data->last_updated = jiffies;
 		data->valid = 1;

drivers/hwmon/coretemp.c

@@ -190,7 +190,8 @@ static ssize_t show_temp(struct device *dev,
 	return tdata->valid ? sprintf(buf, "%d\n", tdata->temp) : -EAGAIN;
 }
 
-static int adjust_tjmax(struct cpuinfo_x86 *c, u32 id, struct device *dev)
+static int __cpuinit adjust_tjmax(struct cpuinfo_x86 *c, u32 id,
+				  struct device *dev)
 {
 	/* The 100C is default for both mobile and non mobile CPUs */
 
@@ -284,7 +285,8 @@ static int adjust_tjmax(struct cpuinfo_x86 *c, u32 id, struct device *dev)
 	return tjmax;
 }
 
-static int get_tjmax(struct cpuinfo_x86 *c, u32 id, struct device *dev)
+static int __cpuinit get_tjmax(struct cpuinfo_x86 *c, u32 id,
+			       struct device *dev)
 {
 	int err;
 	u32 eax, edx;
@@ -323,7 +325,8 @@ static int get_tjmax(struct cpuinfo_x86 *c, u32 id, struct device *dev)
 	return adjust_tjmax(c, id, dev);
 }
 
-static int create_name_attr(struct platform_data *pdata, struct device *dev)
+static int __devinit create_name_attr(struct platform_data *pdata,
+				      struct device *dev)
 {
 	sysfs_attr_init(&pdata->name_attr.attr);
 	pdata->name_attr.attr.name = "name";
@@ -332,8 +335,8 @@ static int create_name_attr(struct platform_data *pdata, struct device *dev)
 	return device_create_file(dev, &pdata->name_attr);
 }
 
-static int create_core_attrs(struct temp_data *tdata, struct device *dev,
-				int attr_no)
+static int __cpuinit create_core_attrs(struct temp_data *tdata,
+				       struct device *dev, int attr_no)
 {
 	int err, i;
 	static ssize_t (*const rd_ptr[TOTAL_ATTRS]) (struct device *dev,
@@ -383,7 +386,7 @@ static int __cpuinit chk_ucode_version(unsigned int cpu)
 	return 0;
 }
 
-static struct platform_device *coretemp_get_pdev(unsigned int cpu)
+static struct platform_device __cpuinit *coretemp_get_pdev(unsigned int cpu)
 {
 	u16 phys_proc_id = TO_PHYS_ID(cpu);
 	struct pdev_entry *p;
@@ -400,7 +403,8 @@ static struct platform_device *coretemp_get_pdev(unsigned int cpu)
 	return NULL;
 }
 
-static struct temp_data *init_temp_data(unsigned int cpu, int pkg_flag)
+static struct temp_data __cpuinit *init_temp_data(unsigned int cpu,
+						  int pkg_flag)
 {
 	struct temp_data *tdata;
 
@@ -418,7 +422,7 @@ static struct temp_data *init_temp_data(unsigned int cpu, int pkg_flag)
 	return tdata;
 }
 
-static int create_core_data(struct platform_device *pdev,
+static int __cpuinit create_core_data(struct platform_device *pdev,
 				unsigned int cpu, int pkg_flag)
 {
 	struct temp_data *tdata;
@@ -489,7 +493,7 @@ static int create_core_data(struct platform_device *pdev,
 	return err;
 }
 
-static void coretemp_add_core(unsigned int cpu, int pkg_flag)
+static void __cpuinit coretemp_add_core(unsigned int cpu, int pkg_flag)
 {
 	struct platform_device *pdev = coretemp_get_pdev(cpu);
 	int err;
@@ -618,7 +622,7 @@ static int __cpuinit coretemp_device_add(unsigned int cpu)
 	return err;
 }
 
-static void coretemp_device_remove(unsigned int cpu)
+static void __cpuinit coretemp_device_remove(unsigned int cpu)
 {
 	struct pdev_entry *p, *n;
 	u16 phys_proc_id = TO_PHYS_ID(cpu);
@@ -634,7 +638,7 @@ static void coretemp_device_remove(unsigned int cpu)
 	mutex_unlock(&pdev_list_mutex);
 }
 
-static bool is_any_core_online(struct platform_data *pdata)
+static bool __cpuinit is_any_core_online(struct platform_data *pdata)
 {
 	int i;
 

drivers/hwmon/it87.c

@@ -17,6 +17,7 @@
  *            IT8720F  Super I/O chip w/LPC interface
  *            IT8721F  Super I/O chip w/LPC interface
  *            IT8726F  Super I/O chip w/LPC interface
+ *            IT8728F  Super I/O chip w/LPC interface
  *            IT8758E  Super I/O chip w/LPC interface
  *            Sis950   A clone of the IT8705F
  *
@@ -58,7 +59,7 @@
 
 #define DRVNAME "it87"
 
-enum chips { it87, it8712, it8716, it8718, it8720, it8721 };
+enum chips { it87, it8712, it8716, it8718, it8720, it8721, it8728 };
 
 static unsigned short force_id;
 module_param(force_id, ushort, 0);
@@ -135,6 +136,7 @@ static inline void superio_exit(void)
 #define IT8720F_DEVID 0x8720
 #define IT8721F_DEVID 0x8721
 #define IT8726F_DEVID 0x8726
+#define IT8728F_DEVID 0x8728
 #define IT87_ACT_REG  0x30
 #define IT87_BASE_REG 0x60
 
@@ -274,11 +276,31 @@ struct it87_data {
 	s8 auto_temp[3][5];	/* [nr][0] is point1_temp_hyst */
 };
 
+static inline int has_12mv_adc(const struct it87_data *data)
+{
+	/*
+	 * IT8721F and later have a 12 mV ADC, also with internal scaling
+	 * on selected inputs.
+	 */
+	return data->type == it8721
+	    || data->type == it8728;
+}
+
+static inline int has_newer_autopwm(const struct it87_data *data)
+{
+	/*
+	 * IT8721F and later have separate registers for the temperature
+	 * mapping and the manual duty cycle.
+	 */
+	return data->type == it8721
+	    || data->type == it8728;
+}
+
 static u8 in_to_reg(const struct it87_data *data, int nr, long val)
 {
 	long lsb;
 
-	if (data->type == it8721) {
+	if (has_12mv_adc(data)) {
 		if (data->in_scaled & (1 << nr))
 			lsb = 24;
 		else
@@ -292,7 +314,7 @@ static u8 in_to_reg(const struct it87_data *data, int nr, long val)
 
 static int in_from_reg(const struct it87_data *data, int nr, int val)
 {
-	if (data->type == it8721) {
+	if (has_12mv_adc(data)) {
 		if (data->in_scaled & (1 << nr))
 			return val * 24;
 		else
@@ -329,7 +351,7 @@ static inline u16 FAN16_TO_REG(long rpm)
 
 static u8 pwm_to_reg(const struct it87_data *data, long val)
 {
-	if (data->type == it8721)
+	if (has_newer_autopwm(data))
 		return val;
 	else
 		return val >> 1;
@@ -337,7 +359,7 @@ static u8 pwm_to_reg(const struct it87_data *data, long val)
 
 static int pwm_from_reg(const struct it87_data *data, u8 reg)
 {
-	if (data->type == it8721)
+	if (has_newer_autopwm(data))
 		return reg;
 	else
 		return (reg & 0x7f) << 1;
@@ -374,7 +396,8 @@ static inline int has_16bit_fans(const struct it87_data *data)
 	    || data->type == it8716
 	    || data->type == it8718
 	    || data->type == it8720
-	    || data->type == it8721;
+	    || data->type == it8721
+	    || data->type == it8728;
 }
 
 static inline int has_old_autopwm(const struct it87_data *data)
@@ -842,7 +865,7 @@ static ssize_t set_pwm_enable(struct device *dev,
 				 data->fan_main_ctrl);
 	} else {
 		if (val == 1)				/* Manual mode */
-			data->pwm_ctrl[nr] = data->type == it8721 ?
+			data->pwm_ctrl[nr] = has_newer_autopwm(data) ?
 					     data->pwm_temp_map[nr] :
 					     data->pwm_duty[nr];
 		else					/* Automatic mode */
@@ -870,7 +893,7 @@ static ssize_t set_pwm(struct device *dev, struct device_attribute *attr,
 		return -EINVAL;
 
 	mutex_lock(&data->update_lock);
-	if (data->type == it8721) {
+	if (has_newer_autopwm(data)) {
 		/* If we are in automatic mode, the PWM duty cycle register
 		 * is read-only so we can't write the value */
 		if (data->pwm_ctrl[nr] & 0x80) {
@@ -1311,7 +1334,7 @@ static ssize_t show_label(struct device *dev, struct device_attribute *attr,
 	struct it87_data *data = dev_get_drvdata(dev);
 	int nr = to_sensor_dev_attr(attr)->index;
 
-	return sprintf(buf, "%s\n", data->type == it8721 ? labels_it8721[nr]
+	return sprintf(buf, "%s\n", has_12mv_adc(data) ? labels_it8721[nr]
 						       : labels[nr]);
 }
 static SENSOR_DEVICE_ATTR(in3_label, S_IRUGO, show_label, NULL, 0);
@@ -1605,6 +1628,9 @@ static int __init it87_find(unsigned short *address,
 	case IT8721F_DEVID:
 		sio_data->type = it8721;
 		break;
+	case IT8728F_DEVID:
+		sio_data->type = it8728;
+		break;
 	case 0xffff:	/* No device at all */
 		goto exit;
 	default:
@@ -1646,8 +1672,11 @@ static int __init it87_find(unsigned short *address,
 		superio_select(GPIO);
 
 		reg = superio_inb(IT87_SIO_GPIO3_REG);
-		if (sio_data->type == it8721) {
-			/* The IT8721F/IT8758E doesn't have VID pins at all */
+		if (sio_data->type == it8721 || sio_data->type == it8728) {
+			/*
+			 * The IT8721F/IT8758E doesn't have VID pins at all,
+			 * not sure about the IT8728F.
+			 */
 			sio_data->skip_vid = 1;
 		} else {
 			/* We need at least 4 VID pins */
@@ -1692,7 +1721,8 @@ static int __init it87_find(unsigned short *address,
 		}
 		if (reg & (1 << 0))
 			sio_data->internal |= (1 << 0);
-		if ((reg & (1 << 1)) || sio_data->type == it8721)
+		if ((reg & (1 << 1)) || sio_data->type == it8721 ||
+		    sio_data->type == it8728)
 			sio_data->internal |= (1 << 1);
 
 		sio_data->beep_pin = superio_inb(IT87_SIO_BEEP_PIN_REG) & 0x3f;
@@ -1770,6 +1800,7 @@ static int __devinit it87_probe(struct platform_device *pdev)
 		"it8718",
 		"it8720",
 		"it8721",
+		"it8728",
 	};
 
 	res = platform_get_resource(pdev, IORESOURCE_IO, 0);
@@ -1807,7 +1838,7 @@ static int __devinit it87_probe(struct platform_device *pdev)
 	enable_pwm_interface = it87_check_pwm(dev);
 
 	/* Starting with IT8721F, we handle scaling of internal voltages */
-	if (data->type == it8721) {
+	if (has_12mv_adc(data)) {
 		if (sio_data->internal & (1 << 0))
 			data->in_scaled |= (1 << 3);	/* in3 is AVCC */
 		if (sio_data->internal & (1 << 1))
@@ -2093,7 +2124,7 @@ static void __devinit it87_init_device(struct platform_device *pdev)
 static void it87_update_pwm_ctrl(struct it87_data *data, int nr)
 {
 	data->pwm_ctrl[nr] = it87_read_value(data, IT87_REG_PWM(nr));
-	if (data->type == it8721) {
+	if (has_newer_autopwm(data)) {
 		data->pwm_temp_map[nr] = data->pwm_ctrl[nr] & 0x03;
 		data->pwm_duty[nr] = it87_read_value(data,
 						     IT87_REG_PWM_DUTY(nr));

drivers/hwmon/lm63.c

@@ -47,10 +47,14 @@
 #include <linux/err.h>
 #include <linux/mutex.h>
 #include <linux/sysfs.h>
+#include <linux/types.h>
 
 /*
  * Addresses to scan
- * Address is fully defined internally and cannot be changed.
+ * Address is fully defined internally and cannot be changed except for
+ * LM64 which has one pin dedicated to address selection.
+ * LM63 and LM96163 have address 0x4c.
+ * LM64 can have address 0x18 or 0x4e.
  */
 
 static const unsigned short normal_i2c[] = { 0x18, 0x4c, 0x4e, I2C_CLIENT_END };
@@ -60,6 +64,7 @@ static const unsigned short normal_i2c[] = { 0x18, 0x4c, 0x4e, I2C_CLIENT_END };
  */
 
 #define LM63_REG_CONFIG1		0x03
+#define LM63_REG_CONVRATE		0x04
 #define LM63_REG_CONFIG2		0xBF
 #define LM63_REG_CONFIG_FAN		0x4A
 
@@ -70,6 +75,9 @@ static const unsigned short normal_i2c[] = { 0x18, 0x4c, 0x4e, I2C_CLIENT_END };
 
 #define LM63_REG_PWM_VALUE		0x4C
 #define LM63_REG_PWM_FREQ		0x4D
+#define LM63_REG_LUT_TEMP_HYST		0x4F
+#define LM63_REG_LUT_TEMP(nr)		(0x50 + 2 * (nr))
+#define LM63_REG_LUT_PWM(nr)		(0x51 + 2 * (nr))
 
 #define LM63_REG_LOCAL_TEMP		0x00
 #define LM63_REG_LOCAL_HIGH		0x05
@@ -91,6 +99,16 @@ static const unsigned short normal_i2c[] = { 0x18, 0x4c, 0x4e, I2C_CLIENT_END };
 #define LM63_REG_MAN_ID			0xFE
 #define LM63_REG_CHIP_ID		0xFF
 
+#define LM96163_REG_TRUTHERM		0x30
+#define LM96163_REG_REMOTE_TEMP_U_MSB	0x31
+#define LM96163_REG_REMOTE_TEMP_U_LSB	0x32
+#define LM96163_REG_CONFIG_ENHANCED	0x45
+
+#define LM63_MAX_CONVRATE		9
+
+#define LM63_MAX_CONVRATE_HZ		32
+#define LM96163_MAX_CONVRATE_HZ		26
+
 /*
  * Conversions and various macros
  * For tachometer counts, the LM63 uses 16-bit values.
@@ -112,15 +130,24 @@ static const unsigned short normal_i2c[] = { 0x18, 0x4c, 0x4e, I2C_CLIENT_END };
 				 (val) >= 127000 ? 127 : \
 				 (val) < 0 ? ((val) - 500) / 1000 : \
 				 ((val) + 500) / 1000)
+#define TEMP8U_TO_REG(val)	((val) <= 0 ? 0 : \
+				 (val) >= 255000 ? 255 : \
+				 ((val) + 500) / 1000)
 #define TEMP11_FROM_REG(reg)	((reg) / 32 * 125)
 #define TEMP11_TO_REG(val)	((val) <= -128000 ? 0x8000 : \
 				 (val) >= 127875 ? 0x7FE0 : \
 				 (val) < 0 ? ((val) - 62) / 125 * 32 : \
 				 ((val) + 62) / 125 * 32)
+#define TEMP11U_TO_REG(val)	((val) <= 0 ? 0 : \
+				 (val) >= 255875 ? 0xFFE0 : \
+				 ((val) + 62) / 125 * 32)
 #define HYST_TO_REG(val)	((val) <= 0 ? 0 : \
 				 (val) >= 127000 ? 127 : \
 				 ((val) + 500) / 1000)
 
+#define UPDATE_INTERVAL(max, rate) \
+			((1000 << (LM63_MAX_CONVRATE - (rate))) / (max))
+
 /*
  * Functions declaration
  */
@@ -134,7 +161,7 @@ static struct lm63_data *lm63_update_device(struct device *dev);
 static int lm63_detect(struct i2c_client *client, struct i2c_board_info *info);
 static void lm63_init_client(struct i2c_client *client);
 
-enum chips { lm63, lm64 };
+enum chips { lm63, lm64, lm96163 };
 
 /*
  * Driver data (common to all clients)
@@ -143,6 +170,7 @@ enum chips { lm63, lm64 };
 static const struct i2c_device_id lm63_id[] = {
 	{ "lm63", lm63 },
 	{ "lm64", lm64 },
+	{ "lm96163", lm96163 },
 	{ }
 };
 MODULE_DEVICE_TABLE(i2c, lm63_id);
@@ -167,26 +195,53 @@ struct lm63_data {
 	struct device *hwmon_dev;
 	struct mutex update_lock;
 	char valid; /* zero until following fields are valid */
+	char lut_valid; /* zero until lut fields are valid */
 	unsigned long last_updated; /* in jiffies */
-	int kind;
+	unsigned long lut_last_updated; /* in jiffies */
+	enum chips kind;
 	int temp2_offset;
 
+	int update_interval;	/* in milliseconds */
+	int max_convrate_hz;
+	int lut_size;		/* 8 or 12 */
+
 	/* registers values */
 	u8 config, config_fan;
 	u16 fan[2];	/* 0: input
 			   1: low limit */
 	u8 pwm1_freq;
-	u8 pwm1_value;
-	s8 temp8[3];	/* 0: local input
+	u8 pwm1[13];	/* 0: current output
+			   1-12: lookup table */
+	s8 temp8[15];	/* 0: local input
 			   1: local high limit
-			   2: remote critical limit */
-	s16 temp11[3];	/* 0: remote input
+			   2: remote critical limit
+			   3-14: lookup table */
+	s16 temp11[4];	/* 0: remote input
 			   1: remote low limit
-			   2: remote high limit */
+			   2: remote high limit
+			   3: remote offset */
+	u16 temp11u;	/* remote input (unsigned) */
 	u8 temp2_crit_hyst;
+	u8 lut_temp_hyst;
 	u8 alarms;
+	bool pwm_highres;
+	bool lut_temp_highres;
+	bool remote_unsigned; /* true if unsigned remote upper limits */
+	bool trutherm;
 };
 
+static inline int temp8_from_reg(struct lm63_data *data, int nr)
+{
+	if (data->remote_unsigned)
+		return TEMP8_FROM_REG((u8)data->temp8[nr]);
+	return TEMP8_FROM_REG(data->temp8[nr]);
+}
+
+static inline int lut_temp_from_reg(struct lm63_data *data, int nr)
+{
+	return data->temp8[nr] * (data->lut_temp_highres ? 500 : 1000);
+}
+
 /*
  * Sysfs callback functions and files
  */
@@ -204,7 +259,12 @@ static ssize_t set_fan(struct device *dev, struct device_attribute *dummy,
 {
 	struct i2c_client *client = to_i2c_client(dev);
 	struct lm63_data *data = i2c_get_clientdata(client);
-	unsigned long val = simple_strtoul(buf, NULL, 10);
+	unsigned long val;
+	int err;
+
+	err = kstrtoul(buf, 10, &val);
+	if (err)
+		return err;
 
 	mutex_lock(&data->update_lock);
 	data->fan[1] = FAN_TO_REG(val);
@@ -216,13 +276,22 @@ static ssize_t set_fan(struct device *dev, struct device_attribute *dummy,
 	return count;
 }
 
-static ssize_t show_pwm1(struct device *dev, struct device_attribute *dummy,
+static ssize_t show_pwm1(struct device *dev, struct device_attribute *devattr,
 			 char *buf)
 {
+	struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr);
 	struct lm63_data *data = lm63_update_device(dev);
-	return sprintf(buf, "%d\n", data->pwm1_value >= 2 * data->pwm1_freq ?
-		       255 : (data->pwm1_value * 255 + data->pwm1_freq) /
-		       (2 * data->pwm1_freq));
+	int nr = attr->index;
+	int pwm;
+
+	if (data->pwm_highres)
+		pwm = data->pwm1[nr];
+	else
+		pwm = data->pwm1[nr] >= 2 * data->pwm1_freq ?
+		       255 : (data->pwm1[nr] * 255 + data->pwm1_freq) /
+		       (2 * data->pwm1_freq);
+
+	return sprintf(buf, "%d\n", pwm);
 }
 
 static ssize_t set_pwm1(struct device *dev, struct device_attribute *dummy,
@@ -231,22 +300,26 @@ static ssize_t set_pwm1(struct device *dev, struct device_attribute *dummy,
 	struct i2c_client *client = to_i2c_client(dev);
 	struct lm63_data *data = i2c_get_clientdata(client);
 	unsigned long val;
+	int err;
 
 	if (!(data->config_fan & 0x20)) /* register is read-only */
 		return -EPERM;
 
-	val = simple_strtoul(buf, NULL, 10);
+	err = kstrtoul(buf, 10, &val);
+	if (err)
+		return err;
+
+	val = SENSORS_LIMIT(val, 0, 255);
 	mutex_lock(&data->update_lock);
-	data->pwm1_value = val <= 0 ? 0 :
-			   val >= 255 ? 2 * data->pwm1_freq :
+	data->pwm1[0] = data->pwm_highres ? val :
 			(val * data->pwm1_freq * 2 + 127) / 255;
-	i2c_smbus_write_byte_data(client, LM63_REG_PWM_VALUE, data->pwm1_value);
+	i2c_smbus_write_byte_data(client, LM63_REG_PWM_VALUE, data->pwm1[0]);
 	mutex_unlock(&data->update_lock);
 	return count;
 }
 
-static ssize_t show_pwm1_enable(struct device *dev, struct device_attribute *dummy,
-				char *buf)
+static ssize_t show_pwm1_enable(struct device *dev,
+				struct device_attribute *dummy, char *buf)
 {
 	struct lm63_data *data = lm63_update_device(dev);
 	return sprintf(buf, "%d\n", data->config_fan & 0x20 ? 1 : 2);
@@ -273,21 +346,47 @@ static ssize_t show_remote_temp8(struct device *dev,
 {
 	struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr);
 	struct lm63_data *data = lm63_update_device(dev);
-	return sprintf(buf, "%d\n", TEMP8_FROM_REG(data->temp8[attr->index])
+	return sprintf(buf, "%d\n", temp8_from_reg(data, attr->index)
 		       + data->temp2_offset);
 }
 
-static ssize_t set_local_temp8(struct device *dev,
-			       struct device_attribute *dummy,
+static ssize_t show_lut_temp(struct device *dev,
+			      struct device_attribute *devattr,
+			      char *buf)
+{
+	struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr);
+	struct lm63_data *data = lm63_update_device(dev);
+	return sprintf(buf, "%d\n", lut_temp_from_reg(data, attr->index)
+		       + data->temp2_offset);
+}
+
+static ssize_t set_temp8(struct device *dev, struct device_attribute *devattr,
 			 const char *buf, size_t count)
 {
+	struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr);
 	struct i2c_client *client = to_i2c_client(dev);
 	struct lm63_data *data = i2c_get_clientdata(client);
-	long val = simple_strtol(buf, NULL, 10);
+	int nr = attr->index;
+	int reg = nr == 2 ? LM63_REG_REMOTE_TCRIT : LM63_REG_LOCAL_HIGH;
+	long val;
+	int err;
+	int temp;
+
+	err = kstrtol(buf, 10, &val);
+	if (err)
+		return err;
 
 	mutex_lock(&data->update_lock);
-	data->temp8[1] = TEMP8_TO_REG(val);
-	i2c_smbus_write_byte_data(client, LM63_REG_LOCAL_HIGH, data->temp8[1]);
+	if (nr == 2) {
+		if (data->remote_unsigned)
+			temp = TEMP8U_TO_REG(val - data->temp2_offset);
+		else
+			temp = TEMP8_TO_REG(val - data->temp2_offset);
+	} else {
+		temp = TEMP8_TO_REG(val);
+	}
+	data->temp8[nr] = temp;
+	i2c_smbus_write_byte_data(client, reg, temp);
 	mutex_unlock(&data->update_lock);
 	return count;
 }
@@ -297,28 +396,56 @@ static ssize_t show_temp11(struct device *dev, struct device_attribute *devattr,
 {
 	struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr);
 	struct lm63_data *data = lm63_update_device(dev);
-	return sprintf(buf, "%d\n", TEMP11_FROM_REG(data->temp11[attr->index])
-		       + data->temp2_offset);
+	int nr = attr->index;
+	int temp;
+
+	if (!nr) {
+		/*
+		 * Use unsigned temperature unless its value is zero.
+		 * If it is zero, use signed temperature.
+		 */
+		if (data->temp11u)
+			temp = TEMP11_FROM_REG(data->temp11u);
+		else
+			temp = TEMP11_FROM_REG(data->temp11[nr]);
+	} else {
+		if (data->remote_unsigned && nr == 2)
+			temp = TEMP11_FROM_REG((u16)data->temp11[nr]);
+		else
+			temp = TEMP11_FROM_REG(data->temp11[nr]);
+	}
+	return sprintf(buf, "%d\n", temp + data->temp2_offset);
 }
 
 static ssize_t set_temp11(struct device *dev, struct device_attribute *devattr,
 			  const char *buf, size_t count)
 {
-	static const u8 reg[4] = {
+	static const u8 reg[6] = {
 		LM63_REG_REMOTE_LOW_MSB,
 		LM63_REG_REMOTE_LOW_LSB,
 		LM63_REG_REMOTE_HIGH_MSB,
 		LM63_REG_REMOTE_HIGH_LSB,
+		LM63_REG_REMOTE_OFFSET_MSB,
+		LM63_REG_REMOTE_OFFSET_LSB,
 	};
 
 	struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr);
 	struct i2c_client *client = to_i2c_client(dev);
 	struct lm63_data *data = i2c_get_clientdata(client);
-	long val = simple_strtol(buf, NULL, 10);
+	long val;
+	int err;
 	int nr = attr->index;
 
+	err = kstrtol(buf, 10, &val);
+	if (err)
+		return err;
+
 	mutex_lock(&data->update_lock);
+	if (data->remote_unsigned && nr == 2)
+		data->temp11[nr] = TEMP11U_TO_REG(val - data->temp2_offset);
+	else
 		data->temp11[nr] = TEMP11_TO_REG(val - data->temp2_offset);
+
 	i2c_smbus_write_byte_data(client, reg[(nr - 1) * 2],
 				  data->temp11[nr] >> 8);
 	i2c_smbus_write_byte_data(client, reg[(nr - 1) * 2 + 1],
@@ -327,35 +454,143 @@ static ssize_t set_temp11(struct device *dev, struct device_attribute *devattr,
 	return count;
 }
 
-/* Hysteresis register holds a relative value, while we want to present
-   an absolute to user-space */
-static ssize_t show_temp2_crit_hyst(struct device *dev, struct device_attribute *dummy,
-				    char *buf)
+/*
+ * Hysteresis register holds a relative value, while we want to present
+ * an absolute to user-space
+ */
+static ssize_t show_temp2_crit_hyst(struct device *dev,
+				    struct device_attribute *dummy, char *buf)
 {
 	struct lm63_data *data = lm63_update_device(dev);
-	return sprintf(buf, "%d\n", TEMP8_FROM_REG(data->temp8[2])
+	return sprintf(buf, "%d\n", temp8_from_reg(data, 2)
 		       + data->temp2_offset
 		       - TEMP8_FROM_REG(data->temp2_crit_hyst));
 }
 
-/* And now the other way around, user-space provides an absolute
-   hysteresis value and we have to store a relative one */
-static ssize_t set_temp2_crit_hyst(struct device *dev, struct device_attribute *dummy,
+static ssize_t show_lut_temp_hyst(struct device *dev,
+				  struct device_attribute *devattr, char *buf)
+{
+	struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr);
+	struct lm63_data *data = lm63_update_device(dev);
+
+	return sprintf(buf, "%d\n", lut_temp_from_reg(data, attr->index)
+		       + data->temp2_offset
+		       - TEMP8_FROM_REG(data->lut_temp_hyst));
+}
+
+/*
+ * And now the other way around, user-space provides an absolute
+ * hysteresis value and we have to store a relative one
+ */
+static ssize_t set_temp2_crit_hyst(struct device *dev,
+				   struct device_attribute *dummy,
 				   const char *buf, size_t count)
 {
 	struct i2c_client *client = to_i2c_client(dev);
 	struct lm63_data *data = i2c_get_clientdata(client);
-	long val = simple_strtol(buf, NULL, 10);
+	long val;
+	int err;
 	long hyst;
 
+	err = kstrtol(buf, 10, &val);
+	if (err)
+		return err;
+
 	mutex_lock(&data->update_lock);
-	hyst = TEMP8_FROM_REG(data->temp8[2]) + data->temp2_offset - val;
+	hyst = temp8_from_reg(data, 2) + data->temp2_offset - val;
 	i2c_smbus_write_byte_data(client, LM63_REG_REMOTE_TCRIT_HYST,
 				  HYST_TO_REG(hyst));
 	mutex_unlock(&data->update_lock);
 	return count;
 }
 
+/*
+ * Set conversion rate.
+ * client->update_lock must be held when calling this function.
+ */
+static void lm63_set_convrate(struct i2c_client *client, struct lm63_data *data,
+			      unsigned int interval)
+{
+	int i;
+	unsigned int update_interval;
+
+	/* Shift calculations to avoid rounding errors */
+	interval <<= 6;
+
+	/* find the nearest update rate */
+	update_interval = (1 << (LM63_MAX_CONVRATE + 6)) * 1000
+	  / data->max_convrate_hz;
+	for (i = 0; i < LM63_MAX_CONVRATE; i++, update_interval >>= 1)
+		if (interval >= update_interval * 3 / 4)
+			break;
+
+	i2c_smbus_write_byte_data(client, LM63_REG_CONVRATE, i);
+	data->update_interval = UPDATE_INTERVAL(data->max_convrate_hz, i);
+}
+
+static ssize_t show_update_interval(struct device *dev,
+				    struct device_attribute *attr, char *buf)
+{
+	struct lm63_data *data = dev_get_drvdata(dev);
+
+	return sprintf(buf, "%u\n", data->update_interval);
+}
+
+static ssize_t set_update_interval(struct device *dev,
+				   struct device_attribute *attr,
+				   const char *buf, size_t count)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct lm63_data *data = i2c_get_clientdata(client);
+	unsigned long val;
+	int err;
+
+	err = kstrtoul(buf, 10, &val);
+	if (err)
+		return err;
+
+	mutex_lock(&data->update_lock);
+	lm63_set_convrate(client, data, SENSORS_LIMIT(val, 0, 100000));
+	mutex_unlock(&data->update_lock);
+
+	return count;
+}
+
+static ssize_t show_type(struct device *dev, struct device_attribute *attr,
+			 char *buf)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct lm63_data *data = i2c_get_clientdata(client);
+
+	return sprintf(buf, data->trutherm ? "1\n" : "2\n");
+}
+
+static ssize_t set_type(struct device *dev, struct device_attribute *attr,
+			const char *buf, size_t count)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct lm63_data *data = i2c_get_clientdata(client);
+	unsigned long val;
+	int ret;
+	u8 reg;
+
+	ret = kstrtoul(buf, 10, &val);
+	if (ret < 0)
+		return ret;
+	if (val != 1 && val != 2)
+		return -EINVAL;
+
+	mutex_lock(&data->update_lock);
+	data->trutherm = val == 1;
+	reg = i2c_smbus_read_byte_data(client, LM96163_REG_TRUTHERM) & ~0x02;
+	i2c_smbus_write_byte_data(client, LM96163_REG_TRUTHERM,
+				  reg | (data->trutherm ? 0x02 : 0x00));
+	data->valid = 0;
+	mutex_unlock(&data->update_lock);
+
+	return count;
+}
+
 static ssize_t show_alarms(struct device *dev, struct device_attribute *dummy,
 			   char *buf)
 {
@@ -377,27 +612,87 @@ static SENSOR_DEVICE_ATTR(fan1_input, S_IRUGO, show_fan, NULL, 0);
 static SENSOR_DEVICE_ATTR(fan1_min, S_IWUSR | S_IRUGO, show_fan,
 	set_fan, 1);
 
-static DEVICE_ATTR(pwm1, S_IWUSR | S_IRUGO, show_pwm1, set_pwm1);
+static SENSOR_DEVICE_ATTR(pwm1, S_IWUSR | S_IRUGO, show_pwm1, set_pwm1, 0);
 static DEVICE_ATTR(pwm1_enable, S_IRUGO, show_pwm1_enable, NULL);
+static SENSOR_DEVICE_ATTR(pwm1_auto_point1_pwm, S_IRUGO, show_pwm1, NULL, 1);
+static SENSOR_DEVICE_ATTR(pwm1_auto_point1_temp, S_IRUGO,
+	show_lut_temp, NULL, 3);
+static SENSOR_DEVICE_ATTR(pwm1_auto_point1_temp_hyst, S_IRUGO,
+	show_lut_temp_hyst, NULL, 3);
+static SENSOR_DEVICE_ATTR(pwm1_auto_point2_pwm, S_IRUGO, show_pwm1, NULL, 2);
+static SENSOR_DEVICE_ATTR(pwm1_auto_point2_temp, S_IRUGO,
+	show_lut_temp, NULL, 4);
+static SENSOR_DEVICE_ATTR(pwm1_auto_point2_temp_hyst, S_IRUGO,
+	show_lut_temp_hyst, NULL, 4);
+static SENSOR_DEVICE_ATTR(pwm1_auto_point3_pwm, S_IRUGO, show_pwm1, NULL, 3);
+static SENSOR_DEVICE_ATTR(pwm1_auto_point3_temp, S_IRUGO,
+	show_lut_temp, NULL, 5);
+static SENSOR_DEVICE_ATTR(pwm1_auto_point3_temp_hyst, S_IRUGO,
+	show_lut_temp_hyst, NULL, 5);
+static SENSOR_DEVICE_ATTR(pwm1_auto_point4_pwm, S_IRUGO, show_pwm1, NULL, 4);
+static SENSOR_DEVICE_ATTR(pwm1_auto_point4_temp, S_IRUGO,
+	show_lut_temp, NULL, 6);
+static SENSOR_DEVICE_ATTR(pwm1_auto_point4_temp_hyst, S_IRUGO,
+	show_lut_temp_hyst, NULL, 6);
+static SENSOR_DEVICE_ATTR(pwm1_auto_point5_pwm, S_IRUGO, show_pwm1, NULL, 5);
+static SENSOR_DEVICE_ATTR(pwm1_auto_point5_temp, S_IRUGO,
+	show_lut_temp, NULL, 7);
+static SENSOR_DEVICE_ATTR(pwm1_auto_point5_temp_hyst, S_IRUGO,
+	show_lut_temp_hyst, NULL, 7);
+static SENSOR_DEVICE_ATTR(pwm1_auto_point6_pwm, S_IRUGO, show_pwm1, NULL, 6);
+static SENSOR_DEVICE_ATTR(pwm1_auto_point6_temp, S_IRUGO,
+	show_lut_temp, NULL, 8);
+static SENSOR_DEVICE_ATTR(pwm1_auto_point6_temp_hyst, S_IRUGO,
+	show_lut_temp_hyst, NULL, 8);
+static SENSOR_DEVICE_ATTR(pwm1_auto_point7_pwm, S_IRUGO, show_pwm1, NULL, 7);
+static SENSOR_DEVICE_ATTR(pwm1_auto_point7_temp, S_IRUGO,
+	show_lut_temp, NULL, 9);
+static SENSOR_DEVICE_ATTR(pwm1_auto_point7_temp_hyst, S_IRUGO,
+	show_lut_temp_hyst, NULL, 9);
+static SENSOR_DEVICE_ATTR(pwm1_auto_point8_pwm, S_IRUGO, show_pwm1, NULL, 8);
+static SENSOR_DEVICE_ATTR(pwm1_auto_point8_temp, S_IRUGO,
+	show_lut_temp, NULL, 10);
+static SENSOR_DEVICE_ATTR(pwm1_auto_point8_temp_hyst, S_IRUGO,
+	show_lut_temp_hyst, NULL, 10);
+static SENSOR_DEVICE_ATTR(pwm1_auto_point9_pwm, S_IRUGO, show_pwm1, NULL, 9);
+static SENSOR_DEVICE_ATTR(pwm1_auto_point9_temp, S_IRUGO,
+	show_lut_temp, NULL, 11);
+static SENSOR_DEVICE_ATTR(pwm1_auto_point9_temp_hyst, S_IRUGO,
+	show_lut_temp_hyst, NULL, 11);
+static SENSOR_DEVICE_ATTR(pwm1_auto_point10_pwm, S_IRUGO, show_pwm1, NULL, 10);
+static SENSOR_DEVICE_ATTR(pwm1_auto_point10_temp, S_IRUGO,
+	show_lut_temp, NULL, 12);
+static SENSOR_DEVICE_ATTR(pwm1_auto_point10_temp_hyst, S_IRUGO,
+	show_lut_temp_hyst, NULL, 12);
+static SENSOR_DEVICE_ATTR(pwm1_auto_point11_pwm, S_IRUGO, show_pwm1, NULL, 11);
+static SENSOR_DEVICE_ATTR(pwm1_auto_point11_temp, S_IRUGO,
+	show_lut_temp, NULL, 13);
+static SENSOR_DEVICE_ATTR(pwm1_auto_point11_temp_hyst, S_IRUGO,
+	show_lut_temp_hyst, NULL, 13);
+static SENSOR_DEVICE_ATTR(pwm1_auto_point12_pwm, S_IRUGO, show_pwm1, NULL, 12);
+static SENSOR_DEVICE_ATTR(pwm1_auto_point12_temp, S_IRUGO,
+	show_lut_temp, NULL, 14);
+static SENSOR_DEVICE_ATTR(pwm1_auto_point12_temp_hyst, S_IRUGO,
+	show_lut_temp_hyst, NULL, 14);
 
 static SENSOR_DEVICE_ATTR(temp1_input, S_IRUGO, show_local_temp8, NULL, 0);
 static SENSOR_DEVICE_ATTR(temp1_max, S_IWUSR | S_IRUGO, show_local_temp8,
-	set_local_temp8, 1);
+	set_temp8, 1);
 
 static SENSOR_DEVICE_ATTR(temp2_input, S_IRUGO, show_temp11, NULL, 0);
 static SENSOR_DEVICE_ATTR(temp2_min, S_IWUSR | S_IRUGO, show_temp11,
 	set_temp11, 1);
 static SENSOR_DEVICE_ATTR(temp2_max, S_IWUSR | S_IRUGO, show_temp11,
 	set_temp11, 2);
-/*
- * On LM63, temp2_crit can be set only once, which should be job
- * of the bootloader.
- */
+static SENSOR_DEVICE_ATTR(temp2_offset, S_IWUSR | S_IRUGO, show_temp11,
+	set_temp11, 3);
 static SENSOR_DEVICE_ATTR(temp2_crit, S_IRUGO, show_remote_temp8,
-	NULL, 2);
+	set_temp8, 2);
 static DEVICE_ATTR(temp2_crit_hyst, S_IWUSR | S_IRUGO, show_temp2_crit_hyst,
 	set_temp2_crit_hyst);
 
+static DEVICE_ATTR(temp2_type, S_IWUSR | S_IRUGO, show_type, set_type);
+
 /* Individual alarm files */
 static SENSOR_DEVICE_ATTR(fan1_min_alarm, S_IRUGO, show_alarm, NULL, 0);
 static SENSOR_DEVICE_ATTR(temp2_crit_alarm, S_IRUGO, show_alarm, NULL, 1);
@@ -408,14 +703,43 @@ static SENSOR_DEVICE_ATTR(temp1_max_alarm, S_IRUGO, show_alarm, NULL, 6);
 /* Raw alarm file for compatibility */
 static DEVICE_ATTR(alarms, S_IRUGO, show_alarms, NULL);
 
+static DEVICE_ATTR(update_interval, S_IRUGO | S_IWUSR, show_update_interval,
+		   set_update_interval);
+
 static struct attribute *lm63_attributes[] = {
-	&dev_attr_pwm1.attr,
+	&sensor_dev_attr_pwm1.dev_attr.attr,
 	&dev_attr_pwm1_enable.attr,
+	&sensor_dev_attr_pwm1_auto_point1_pwm.dev_attr.attr,
+	&sensor_dev_attr_pwm1_auto_point1_temp.dev_attr.attr,
+	&sensor_dev_attr_pwm1_auto_point1_temp_hyst.dev_attr.attr,
+	&sensor_dev_attr_pwm1_auto_point2_pwm.dev_attr.attr,
+	&sensor_dev_attr_pwm1_auto_point2_temp.dev_attr.attr,
+	&sensor_dev_attr_pwm1_auto_point2_temp_hyst.dev_attr.attr,
+	&sensor_dev_attr_pwm1_auto_point3_pwm.dev_attr.attr,
+	&sensor_dev_attr_pwm1_auto_point3_temp.dev_attr.attr,
+	&sensor_dev_attr_pwm1_auto_point3_temp_hyst.dev_attr.attr,
+	&sensor_dev_attr_pwm1_auto_point4_pwm.dev_attr.attr,
+	&sensor_dev_attr_pwm1_auto_point4_temp.dev_attr.attr,
+	&sensor_dev_attr_pwm1_auto_point4_temp_hyst.dev_attr.attr,
+	&sensor_dev_attr_pwm1_auto_point5_pwm.dev_attr.attr,
+	&sensor_dev_attr_pwm1_auto_point5_temp.dev_attr.attr,
+	&sensor_dev_attr_pwm1_auto_point5_temp_hyst.dev_attr.attr,
+	&sensor_dev_attr_pwm1_auto_point6_pwm.dev_attr.attr,
+	&sensor_dev_attr_pwm1_auto_point6_temp.dev_attr.attr,
+	&sensor_dev_attr_pwm1_auto_point6_temp_hyst.dev_attr.attr,
+	&sensor_dev_attr_pwm1_auto_point7_pwm.dev_attr.attr,
+	&sensor_dev_attr_pwm1_auto_point7_temp.dev_attr.attr,
+	&sensor_dev_attr_pwm1_auto_point7_temp_hyst.dev_attr.attr,
+	&sensor_dev_attr_pwm1_auto_point8_pwm.dev_attr.attr,
+	&sensor_dev_attr_pwm1_auto_point8_temp.dev_attr.attr,
+	&sensor_dev_attr_pwm1_auto_point8_temp_hyst.dev_attr.attr,
+
 	&sensor_dev_attr_temp1_input.dev_attr.attr,
 	&sensor_dev_attr_temp2_input.dev_attr.attr,
 	&sensor_dev_attr_temp2_min.dev_attr.attr,
 	&sensor_dev_attr_temp1_max.dev_attr.attr,
 	&sensor_dev_attr_temp2_max.dev_attr.attr,
+	&sensor_dev_attr_temp2_offset.dev_attr.attr,
 	&sensor_dev_attr_temp2_crit.dev_attr.attr,
 	&dev_attr_temp2_crit_hyst.attr,
 
@@ -425,10 +749,54 @@ static struct attribute *lm63_attributes[] = {
 	&sensor_dev_attr_temp2_max_alarm.dev_attr.attr,
 	&sensor_dev_attr_temp1_max_alarm.dev_attr.attr,
 	&dev_attr_alarms.attr,
+	&dev_attr_update_interval.attr,
+	NULL
+};
+
+static struct attribute *lm63_attributes_extra_lut[] = {
+	&sensor_dev_attr_pwm1_auto_point9_pwm.dev_attr.attr,
+	&sensor_dev_attr_pwm1_auto_point9_temp.dev_attr.attr,
+	&sensor_dev_attr_pwm1_auto_point9_temp_hyst.dev_attr.attr,
+	&sensor_dev_attr_pwm1_auto_point10_pwm.dev_attr.attr,
+	&sensor_dev_attr_pwm1_auto_point10_temp.dev_attr.attr,
+	&sensor_dev_attr_pwm1_auto_point10_temp_hyst.dev_attr.attr,
+	&sensor_dev_attr_pwm1_auto_point11_pwm.dev_attr.attr,
+	&sensor_dev_attr_pwm1_auto_point11_temp.dev_attr.attr,
+	&sensor_dev_attr_pwm1_auto_point11_temp_hyst.dev_attr.attr,
+	&sensor_dev_attr_pwm1_auto_point12_pwm.dev_attr.attr,
+	&sensor_dev_attr_pwm1_auto_point12_temp.dev_attr.attr,
+	&sensor_dev_attr_pwm1_auto_point12_temp_hyst.dev_attr.attr,
 	NULL
 };
 
+static const struct attribute_group lm63_group_extra_lut = {
+	.attrs = lm63_attributes_extra_lut,
+};
+
+/*
+ * On LM63, temp2_crit can be set only once, which should be job
+ * of the bootloader.
+ * On LM64, temp2_crit can always be set.
+ * On LM96163, temp2_crit can be set if bit 1 of the configuration
+ * register is true.
+ */
+static umode_t lm63_attribute_mode(struct kobject *kobj,
+				   struct attribute *attr, int index)
+{
+	struct device *dev = container_of(kobj, struct device, kobj);
+	struct i2c_client *client = to_i2c_client(dev);
+	struct lm63_data *data = i2c_get_clientdata(client);
+
+	if (attr == &sensor_dev_attr_temp2_crit.dev_attr.attr
+	    && (data->kind == lm64 ||
+		(data->kind == lm96163 && (data->config & 0x02))))
+		return attr->mode | S_IWUSR;
+
+	return attr->mode;
+}
+
 static const struct attribute_group lm63_group = {
+	.is_visible = lm63_attribute_mode,
 	.attrs = lm63_attributes,
 };
 
@@ -487,6 +855,8 @@ static int lm63_detect(struct i2c_client *new_client,
 		strlcpy(info->type, "lm63", I2C_NAME_SIZE);
 	else if (chip_id == 0x51 && (address == 0x18 || address == 0x4e))
 		strlcpy(info->type, "lm64", I2C_NAME_SIZE);
+	else if (chip_id == 0x49 && address == 0x4c)
+		strlcpy(info->type, "lm96163", I2C_NAME_SIZE);
 	else
 		return -ENODEV;
 
@@ -518,12 +888,24 @@ static int lm63_probe(struct i2c_client *new_client,
 	lm63_init_client(new_client);
 
 	/* Register sysfs hooks */
-	if ((err = sysfs_create_group(&new_client->dev.kobj,
-				      &lm63_group)))
+	err = sysfs_create_group(&new_client->dev.kobj, &lm63_group);
+	if (err)
 		goto exit_free;
 	if (data->config & 0x04) { /* tachometer enabled */
-		if ((err = sysfs_create_group(&new_client->dev.kobj,
-					      &lm63_group_fan1)))
+		err = sysfs_create_group(&new_client->dev.kobj,
+					 &lm63_group_fan1);
+		if (err)
+			goto exit_remove_files;
+	}
+	if (data->kind == lm96163) {
+		err = device_create_file(&new_client->dev,
+					 &dev_attr_temp2_type);
+		if (err)
+			goto exit_remove_files;
+
+		err = sysfs_create_group(&new_client->dev.kobj,
+					 &lm63_group_extra_lut);
+		if (err)
 			goto exit_remove_files;
 	}
 
@@ -538,17 +920,25 @@ static int lm63_probe(struct i2c_client *new_client,
 exit_remove_files:
 	sysfs_remove_group(&new_client->dev.kobj, &lm63_group);
 	sysfs_remove_group(&new_client->dev.kobj, &lm63_group_fan1);
+	if (data->kind == lm96163) {
+		device_remove_file(&new_client->dev, &dev_attr_temp2_type);
+		sysfs_remove_group(&new_client->dev.kobj,
+				   &lm63_group_extra_lut);
+	}
 exit_free:
 	kfree(data);
 exit:
 	return err;
 }
 
-/* Idealy we shouldn't have to initialize anything, since the BIOS
-   should have taken care of everything */
+/*
+ * Ideally we shouldn't have to initialize anything, since the BIOS
+ * should have taken care of everything
+ */
 static void lm63_init_client(struct i2c_client *client)
 {
 	struct lm63_data *data = i2c_get_clientdata(client);
+	u8 convrate;
 
 	data->config = i2c_smbus_read_byte_data(client, LM63_REG_CONFIG1);
 	data->config_fan = i2c_smbus_read_byte_data(client,
@@ -561,13 +951,54 @@ static void lm63_init_client(struct i2c_client *client)
 		i2c_smbus_write_byte_data(client, LM63_REG_CONFIG1,
 					  data->config);
 	}
+	/* Tachometer is always enabled on LM64 */
+	if (data->kind == lm64)
+		data->config |= 0x04;
 
 	/* We may need pwm1_freq before ever updating the client data */
 	data->pwm1_freq = i2c_smbus_read_byte_data(client, LM63_REG_PWM_FREQ);
 	if (data->pwm1_freq == 0)
 		data->pwm1_freq = 1;
 
+	switch (data->kind) {
+	case lm63:
+	case lm64:
+		data->max_convrate_hz = LM63_MAX_CONVRATE_HZ;
+		data->lut_size = 8;
+		break;
+	case lm96163:
+		data->max_convrate_hz = LM96163_MAX_CONVRATE_HZ;
+		data->lut_size = 12;
+		data->trutherm
+		  = i2c_smbus_read_byte_data(client,
+					     LM96163_REG_TRUTHERM) & 0x02;
+		break;
+	}
+	convrate = i2c_smbus_read_byte_data(client, LM63_REG_CONVRATE);
+	if (unlikely(convrate > LM63_MAX_CONVRATE))
+		convrate = LM63_MAX_CONVRATE;
+	data->update_interval = UPDATE_INTERVAL(data->max_convrate_hz,
+						convrate);
+
+	/*
+	 * For LM96163, check if high resolution PWM
+	 * and unsigned temperature format is enabled.
+	 */
+	if (data->kind == lm96163) {
+		u8 config_enhanced
+		  = i2c_smbus_read_byte_data(client,
+					     LM96163_REG_CONFIG_ENHANCED);
+		if (config_enhanced & 0x20)
+			data->lut_temp_highres = true;
+		if ((config_enhanced & 0x10)
+		    && !(data->config_fan & 0x08) && data->pwm1_freq == 8)
+			data->pwm_highres = true;
+		if (config_enhanced & 0x08)
+			data->remote_unsigned = true;
+	}
+
 	/* Show some debug info about the LM63 configuration */
+	if (data->kind == lm63)
 		dev_dbg(&client->dev, "Alert/tach pin configured for %s\n",
 			(data->config & 0x04) ? "tachometer input" :
 			"alert output");
@@ -586,6 +1017,10 @@ static int lm63_remove(struct i2c_client *client)
 	hwmon_device_unregister(data->hwmon_dev);
 	sysfs_remove_group(&client->dev.kobj, &lm63_group);
 	sysfs_remove_group(&client->dev.kobj, &lm63_group_fan1);
+	if (data->kind == lm96163) {
+		device_remove_file(&client->dev, &dev_attr_temp2_type);
+		sysfs_remove_group(&client->dev.kobj, &lm63_group_extra_lut);
+	}
 
 	kfree(data);
 	return 0;
@@ -595,10 +1030,15 @@ static struct lm63_data *lm63_update_device(struct device *dev)
 {
 	struct i2c_client *client = to_i2c_client(dev);
 	struct lm63_data *data = i2c_get_clientdata(client);
+	unsigned long next_update;
+	int i;
 
 	mutex_lock(&data->update_lock);
 
-	if (time_after(jiffies, data->last_updated + HZ) || !data->valid) {
+	next_update = data->last_updated
+	  + msecs_to_jiffies(data->update_interval) + 1;
+
+	if (time_after(jiffies, next_update) || !data->valid) {
 		if (data->config & 0x04) { /* tachometer enabled  */
 			/* order matters for fan1_input */
 			data->fan[0] = i2c_smbus_read_byte_data(client,
@@ -615,7 +1055,7 @@ static struct lm63_data *lm63_update_device(struct device *dev)
 				  LM63_REG_PWM_FREQ);
 		if (data->pwm1_freq == 0)
 			data->pwm1_freq = 1;
-		data->pwm1_value = i2c_smbus_read_byte_data(client,
+		data->pwm1[0] = i2c_smbus_read_byte_data(client,
 				LM63_REG_PWM_VALUE);
 
 		data->temp8[0] = i2c_smbus_read_byte_data(client,
@@ -636,6 +1076,17 @@ static struct lm63_data *lm63_update_device(struct device *dev)
 				  LM63_REG_REMOTE_HIGH_MSB) << 8)
 				| i2c_smbus_read_byte_data(client,
 				  LM63_REG_REMOTE_HIGH_LSB);
+		data->temp11[3] = (i2c_smbus_read_byte_data(client,
+				  LM63_REG_REMOTE_OFFSET_MSB) << 8)
+				| i2c_smbus_read_byte_data(client,
+				  LM63_REG_REMOTE_OFFSET_LSB);
+
+		if (data->kind == lm96163)
+			data->temp11u = (i2c_smbus_read_byte_data(client,
+					LM96163_REG_REMOTE_TEMP_U_MSB) << 8)
+				      | i2c_smbus_read_byte_data(client,
+					LM96163_REG_REMOTE_TEMP_U_LSB);
+
 		data->temp8[2] = i2c_smbus_read_byte_data(client,
 				 LM63_REG_REMOTE_TCRIT);
 		data->temp2_crit_hyst = i2c_smbus_read_byte_data(client,
@@ -648,6 +1099,21 @@ static struct lm63_data *lm63_update_device(struct device *dev)
 		data->valid = 1;
 	}
 
+	if (time_after(jiffies, data->lut_last_updated + 5 * HZ) ||
+	    !data->lut_valid) {
+		for (i = 0; i < data->lut_size; i++) {
+			data->pwm1[1 + i] = i2c_smbus_read_byte_data(client,
+					    LM63_REG_LUT_PWM(i));
+			data->temp8[3 + i] = i2c_smbus_read_byte_data(client,
+					     LM63_REG_LUT_TEMP(i));
+		}
+		data->lut_temp_hyst = i2c_smbus_read_byte_data(client,
+				      LM63_REG_LUT_TEMP_HYST);
+
+		data->lut_last_updated = jiffies;
+		data->lut_valid = 1;
+	}
+
 	mutex_unlock(&data->update_lock);
 
 	return data;

drivers/hwmon/lm90.c

@@ -917,7 +917,7 @@ static ssize_t set_update_interval(struct device *dev,
 		return err;
 
 	mutex_lock(&data->update_lock);
-	lm90_set_convrate(client, data, val);
+	lm90_set_convrate(client, data, SENSORS_LIMIT(val, 0, 100000));
 	mutex_unlock(&data->update_lock);
 
 	return count;

drivers/hwmon/max1111.c

@@ -106,11 +106,14 @@ static ssize_t show_adc(struct device *dev,
 	if (ret < 0)
 		return ret;
 
-	return sprintf(buf, "%d\n", ret);
+	/* assume the reference voltage to be 2.048V, with an 8-bit sample,
+	 * the LSB weight is 8mV
+	 */
+	return sprintf(buf, "%d\n", ret * 8);
 }
 
 #define MAX1111_ADC_ATTR(_id)		\
-	SENSOR_DEVICE_ATTR(adc##_id##_in, S_IRUGO, show_adc, NULL, _id)
+	SENSOR_DEVICE_ATTR(in##_id##_input, S_IRUGO, show_adc, NULL, _id)
 
 static DEVICE_ATTR(name, S_IRUGO, show_name, NULL);
 static MAX1111_ADC_ATTR(0);
@@ -120,10 +123,10 @@ static MAX1111_ADC_ATTR(3);
 
 static struct attribute *max1111_attributes[] = {
 	&dev_attr_name.attr,
-	&sensor_dev_attr_adc0_in.dev_attr.attr,
-	&sensor_dev_attr_adc1_in.dev_attr.attr,
-	&sensor_dev_attr_adc2_in.dev_attr.attr,
-	&sensor_dev_attr_adc3_in.dev_attr.attr,
+	&sensor_dev_attr_in0_input.dev_attr.attr,
+	&sensor_dev_attr_in1_input.dev_attr.attr,
+	&sensor_dev_attr_in2_input.dev_attr.attr,
+	&sensor_dev_attr_in3_input.dev_attr.attr,
 	NULL,
 };