Skip to content

L
linux
Commit b2bc415b authored by Christian Daudt's avatar Christian Daudt Committed by David Woodhouse
Browse files
Options

mtd: remove bcmring NAND driver 

This driver is being removed as part of the cleanup of the bcmring
SoC from mainline as it is no longer maintained.
Signed-off-by: default avatarChristian Daudt <csd@broadcom.com>
Reviewed-by: default avatarJiandong Zheng <jdzheng@broadcom.com>
Acked-by: default avatarWill Deacon <will.deacon@arm.com>
Signed-off-by: default avatarArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: default avatarDavid Woodhouse <David.Woodhouse@intel.com>
parent 5ca7f415
Expand all Show whitespace changes
Inline Side-by-side
Showing with 0 additions and 1255 deletions
MAINTAINERS
View file @ b2bc415b
...@@ -665,15 +665,6 @@ L: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers) ...@@ -665,15 +665,6 @@ L: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
S: Maintained S: Maintained
F: arch/arm/mach-bcmring F: arch/arm/mach-bcmring
ARM/BCMRING MTD NAND DRIVER
M: Jiandong Zheng <jdzheng@broadcom.com>
M: Scott Branden <sbranden@broadcom.com>
L: linux-mtd@lists.infradead.org
S: Maintained
F: drivers/mtd/nand/bcm_umi_nand.c
F: drivers/mtd/nand/bcm_umi_bch.c
F: drivers/mtd/nand/nand_bcm_umi.h
ARM/CALXEDA HIGHBANK ARCHITECTURE ARM/CALXEDA HIGHBANK ARCHITECTURE
M: Rob Herring <rob.herring@calxeda.com> M: Rob Herring <rob.herring@calxeda.com>
L: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers) L: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
......
drivers/mtd/nand/Kconfig
View file @ b2bc415b
...@@ -258,22 +258,6 @@ config MTD_NAND_S3C2410_CLKSTOP ...@@ -258,22 +258,6 @@ config MTD_NAND_S3C2410_CLKSTOP
when the is NAND chip selected or released, but will save when the is NAND chip selected or released, but will save
approximately 5mA of power when there is nothing happening. approximately 5mA of power when there is nothing happening.
config MTD_NAND_BCM_UMI
tristate "NAND Flash support for BCM Reference Boards"
depends on ARCH_BCMRING
help
This enables the NAND flash controller on the BCM UMI block.
No board specific support is done by this driver, each board
must advertise a platform_device for the driver to attach.
config MTD_NAND_BCM_UMI_HWCS
bool "BCM UMI NAND Hardware CS"
depends on MTD_NAND_BCM_UMI
help
Enable the use of the BCM UMI block's internal CS using NAND.
This should only be used if you know the external NAND CS can toggle.
config MTD_NAND_DISKONCHIP config MTD_NAND_DISKONCHIP
tristate "DiskOnChip 2000, Millennium and Millennium Plus (NAND reimplementation) (EXPERIMENTAL)" tristate "DiskOnChip 2000, Millennium and Millennium Plus (NAND reimplementation) (EXPERIMENTAL)"
depends on EXPERIMENTAL depends on EXPERIMENTAL
......
drivers/mtd/nand/Makefile
View file @ b2bc415b
...@@ -48,7 +48,6 @@ obj-$(CONFIG_MTD_NAND_SOCRATES) += socrates_nand.o ...@@ -48,7 +48,6 @@ obj-$(CONFIG_MTD_NAND_SOCRATES) += socrates_nand.o
obj-$(CONFIG_MTD_NAND_TXX9NDFMC) += txx9ndfmc.o obj-$(CONFIG_MTD_NAND_TXX9NDFMC) += txx9ndfmc.o
obj-$(CONFIG_MTD_NAND_NUC900) += nuc900_nand.o obj-$(CONFIG_MTD_NAND_NUC900) += nuc900_nand.o
obj-$(CONFIG_MTD_NAND_NOMADIK) += nomadik_nand.o obj-$(CONFIG_MTD_NAND_NOMADIK) += nomadik_nand.o
obj-$(CONFIG_MTD_NAND_BCM_UMI) += bcm_umi_nand.o nand_bcm_umi.o
obj-$(CONFIG_MTD_NAND_MPC5121_NFC) += mpc5121_nfc.o obj-$(CONFIG_MTD_NAND_MPC5121_NFC) += mpc5121_nfc.o
obj-$(CONFIG_MTD_NAND_RICOH) += r852.o obj-$(CONFIG_MTD_NAND_RICOH) += r852.o
obj-$(CONFIG_MTD_NAND_JZ4740) += jz4740_nand.o obj-$(CONFIG_MTD_NAND_JZ4740) += jz4740_nand.o
......
drivers/mtd/nand/bcm_umi_bch.c deleted 100644 → 0
View file @ 5ca7f415
/*****************************************************************************
* Copyright 2004 - 2009 Broadcom Corporation. All rights reserved.
*
* Unless you and Broadcom execute a separate written software license
* agreement governing use of this software, this software is licensed to you
* under the terms of the GNU General Public License version 2, available at
* http://www.broadcom.com/licenses/GPLv2.php (the "GPL").
*
* Notwithstanding the above, under no circumstances may you combine this
* software in any way with any other Broadcom software provided under a
* license other than the GPL, without Broadcom's express prior written
* consent.
*****************************************************************************/
/* ---- Include Files ---------------------------------------------------- */
#include "nand_bcm_umi.h"
/* ---- External Variable Declarations ----------------------------------- */
/* ---- External Function Prototypes ------------------------------------- */
/* ---- Public Variables ------------------------------------------------- */
/* ---- Private Constants and Types -------------------------------------- */
/* ---- Private Function Prototypes -------------------------------------- */
static int bcm_umi_bch_read_page_hwecc(struct mtd_info *mtd,
struct nand_chip *chip, uint8_t *buf, int oob_required, int page);
static int bcm_umi_bch_write_page_hwecc(struct mtd_info *mtd,
struct nand_chip *chip, const uint8_t *buf, int oob_required);
/* ---- Private Variables ------------------------------------------------ */
/*
** nand_hw_eccoob
** New oob placement block for use with hardware ecc generation.
*/
static struct nand_ecclayout nand_hw_eccoob_512 = {
/* Reserve 5 for BI indicator */
.oobfree = {
#if (NAND_ECC_NUM_BYTES > 3)
{.offset = 0, .length = 2}
#else
{.offset = 0, .length = 5},
{.offset = 6, .length = 7}
#endif
}
};
/*
** We treat the OOB for a 2K page as if it were 4 512 byte oobs,
** except the BI is at byte 0.
*/
static struct nand_ecclayout nand_hw_eccoob_2048 = {
/* Reserve 0 as BI indicator */
.oobfree = {
#if (NAND_ECC_NUM_BYTES > 10)
{.offset = 1, .length = 2},
#elif (NAND_ECC_NUM_BYTES > 7)
{.offset = 1, .length = 5},
{.offset = 16, .length = 6},
{.offset = 32, .length = 6},
{.offset = 48, .length = 6}
#else
{.offset = 1, .length = 8},
{.offset = 16, .length = 9},
{.offset = 32, .length = 9},
{.offset = 48, .length = 9}
#endif
}
};
/* We treat the OOB for a 4K page as if it were 8 512 byte oobs,
* except the BI is at byte 0. */
static struct nand_ecclayout nand_hw_eccoob_4096 = {
/* Reserve 0 as BI indicator */
.oobfree = {
#if (NAND_ECC_NUM_BYTES > 10)
{.offset = 1, .length = 2},
{.offset = 16, .length = 3},
{.offset = 32, .length = 3},
{.offset = 48, .length = 3},
{.offset = 64, .length = 3},
{.offset = 80, .length = 3},
{.offset = 96, .length = 3},
{.offset = 112, .length = 3}
#else
{.offset = 1, .length = 5},
{.offset = 16, .length = 6},
{.offset = 32, .length = 6},
{.offset = 48, .length = 6},
{.offset = 64, .length = 6},
{.offset = 80, .length = 6},
{.offset = 96, .length = 6},
{.offset = 112, .length = 6}
#endif
}
};
/* ---- Private Functions ------------------------------------------------ */
/* ==== Public Functions ================================================= */
/****************************************************************************
*
* bcm_umi_bch_read_page_hwecc - hardware ecc based page read function
* @mtd: mtd info structure
* @chip: nand chip info structure
* @buf: buffer to store read data
* @oob_required: caller expects OOB data read to chip->oob_poi
*
***************************************************************************/
static int bcm_umi_bch_read_page_hwecc(struct mtd_info *mtd,
struct nand_chip *chip, uint8_t * buf,
int oob_required, int page)
{
int sectorIdx = 0;
int eccsize = chip->ecc.size;
int eccsteps = chip->ecc.steps;
uint8_t *datap = buf;
uint8_t eccCalc[NAND_ECC_NUM_BYTES];
int sectorOobSize = mtd->oobsize / eccsteps;
int stat;
unsigned int max_bitflips = 0;
for (sectorIdx = 0; sectorIdx < eccsteps;
sectorIdx++, datap += eccsize) {
if (sectorIdx > 0) {
/* Seek to page location within sector */
chip->cmdfunc(mtd, NAND_CMD_RNDOUT, sectorIdx * eccsize,
-1);
}
/* Enable hardware ECC before reading the buf */
nand_bcm_umi_bch_enable_read_hwecc();
/* Read in data */
bcm_umi_nand_read_buf(mtd, datap, eccsize);
/* Pause hardware ECC after reading the buf */
nand_bcm_umi_bch_pause_read_ecc_calc();
/* Read the OOB ECC */
chip->cmdfunc(mtd, NAND_CMD_RNDOUT,
mtd->writesize + sectorIdx * sectorOobSize, -1);
nand_bcm_umi_bch_read_oobEcc(mtd->writesize, eccCalc,
NAND_ECC_NUM_BYTES,
chip->oob_poi +
sectorIdx * sectorOobSize);
/* Correct any ECC detected errors */
stat =
nand_bcm_umi_bch_correct_page(datap, eccCalc,
NAND_ECC_NUM_BYTES);
/* Update Stats */
if (stat < 0) {
#if defined(NAND_BCM_UMI_DEBUG)
printk(KERN_WARNING "%s uncorr_err sectorIdx=%d\n",
__func__, sectorIdx);
printk(KERN_WARNING "%s data %*ph\n",
__func__, 8, datap);
printk(KERN_WARNING "%s ecc %*ph\n",
__func__, 13, eccCalc);
BUG();
#endif
mtd->ecc_stats.failed++;
} else {
#if defined(NAND_BCM_UMI_DEBUG)
if (stat > 0) {
printk(KERN_INFO
"%s %d correctable_errors detected\n",
__func__, stat);
}
#endif
mtd->ecc_stats.corrected += stat;
max_bitflips = max_t(unsigned int, max_bitflips, stat);
}
}
return max_bitflips;
}
/****************************************************************************
*
* bcm_umi_bch_write_page_hwecc - hardware ecc based page write function
* @mtd: mtd info structure
* @chip: nand chip info structure
* @buf: data buffer
* @oob_required: must write chip->oob_poi to OOB
*
***************************************************************************/
static int bcm_umi_bch_write_page_hwecc(struct mtd_info *mtd,
struct nand_chip *chip, const uint8_t *buf, int oob_required)
{
int sectorIdx = 0;
int eccsize = chip->ecc.size;
int eccsteps = chip->ecc.steps;
const uint8_t *datap = buf;
uint8_t *oobp = chip->oob_poi;
int sectorOobSize = mtd->oobsize / eccsteps;
for (sectorIdx = 0; sectorIdx < eccsteps;
sectorIdx++, datap += eccsize, oobp += sectorOobSize) {
/* Enable hardware ECC before writing the buf */
nand_bcm_umi_bch_enable_write_hwecc();
bcm_umi_nand_write_buf(mtd, datap, eccsize);
nand_bcm_umi_bch_write_oobEcc(mtd->writesize, oobp,
NAND_ECC_NUM_BYTES);
}
bcm_umi_nand_write_buf(mtd, chip->oob_poi, mtd->oobsize);
return 0;
}
drivers/mtd/nand/bcm_umi_nand.c deleted 100644 → 0
View file @ 5ca7f415
This diff is collapsed.
drivers/mtd/nand/nand_bcm_umi.c deleted 100644 → 0
View file @ 5ca7f415
/*****************************************************************************
* Copyright 2004 - 2009 Broadcom Corporation. All rights reserved.
*
* Unless you and Broadcom execute a separate written software license
* agreement governing use of this software, this software is licensed to you
* under the terms of the GNU General Public License version 2, available at
* http://www.broadcom.com/licenses/GPLv2.php (the "GPL").
*
* Notwithstanding the above, under no circumstances may you combine this
* software in any way with any other Broadcom software provided under a
* license other than the GPL, without Broadcom's express prior written
* consent.
*****************************************************************************/
/* ---- Include Files ---------------------------------------------------- */
#include <mach/reg_umi.h>
#include "nand_bcm_umi.h"
#ifdef BOOT0_BUILD
#include <uart.h>
#endif
/* ---- External Variable Declarations ----------------------------------- */
/* ---- External Function Prototypes ------------------------------------- */
/* ---- Public Variables ------------------------------------------------- */
/* ---- Private Constants and Types -------------------------------------- */
/* ---- Private Function Prototypes -------------------------------------- */
/* ---- Private Variables ------------------------------------------------ */
/* ---- Private Functions ------------------------------------------------ */
#if NAND_ECC_BCH
/****************************************************************************
* nand_bch_ecc_flip_bit - Routine to flip an errored bit
*
* PURPOSE:
* This is a helper routine that flips the bit (0 -> 1 or 1 -> 0) of the
* errored bit specified
*
* PARAMETERS:
* datap - Container that holds the 512 byte data
* errorLocation - Location of the bit that needs to be flipped
*
* RETURNS:
* None
****************************************************************************/
static void nand_bcm_umi_bch_ecc_flip_bit(uint8_t *datap, int errorLocation)
{
int locWithinAByte = (errorLocation & REG_UMI_BCH_ERR_LOC_BYTE) >> 0;
int locWithinAWord = (errorLocation & REG_UMI_BCH_ERR_LOC_WORD) >> 3;
int locWithinAPage = (errorLocation & REG_UMI_BCH_ERR_LOC_PAGE) >> 5;
uint8_t errorByte = 0;
uint8_t byteMask = 1 << locWithinAByte;
/* BCH uses big endian, need to change the location
* bits to little endian */
locWithinAWord = 3 - locWithinAWord;
errorByte = datap[locWithinAPage * sizeof(uint32_t) + locWithinAWord];
#ifdef BOOT0_BUILD
puthexs("\nECC Correct Offset: ",
locWithinAPage * sizeof(uint32_t) + locWithinAWord);
puthexs(" errorByte:", errorByte);
puthex8(" Bit: ", locWithinAByte);
#endif
if (errorByte & byteMask) {
/* bit needs to be cleared */
errorByte &= ~byteMask;
} else {
/* bit needs to be set */
errorByte |= byteMask;
}
/* write back the value with the fixed bit */
datap[locWithinAPage * sizeof(uint32_t) + locWithinAWord] = errorByte;
}
/****************************************************************************
* nand_correct_page_bch - Routine to correct bit errors when reading NAND
*
* PURPOSE:
* This routine reads the BCH registers to determine if there are any bit
* errors during the read of the last 512 bytes of data + ECC bytes. If
* errors exists, the routine fixes it.
*
* PARAMETERS:
* datap - Container that holds the 512 byte data
*
* RETURNS:
* 0 or greater = Number of errors corrected
* (No errors are found or errors have been fixed)
* -1 = Error(s) cannot be fixed
****************************************************************************/
int nand_bcm_umi_bch_correct_page(uint8_t *datap, uint8_t *readEccData,
int numEccBytes)
{
int numErrors;
int errorLocation;
int idx;
uint32_t regValue;
/* wait for read ECC to be valid */
regValue = nand_bcm_umi_bch_poll_read_ecc_calc();
/*
* read the control status register to determine if there
* are error'ed bits
* see if errors are correctible
*/
if ((regValue & REG_UMI_BCH_CTRL_STATUS_UNCORR_ERR) > 0) {
int i;
for (i = 0; i < numEccBytes; i++) {
if (readEccData[i] != 0xff) {
/* errors cannot be fixed, return -1 */
return -1;
}
}
/* If ECC is unprogrammed then we can't correct,
* assume everything OK */
return 0;
}
if ((regValue & REG_UMI_BCH_CTRL_STATUS_CORR_ERR) == 0) {
/* no errors */
return 0;
}
/*
* Fix errored bits by doing the following:
* 1. Read the number of errors in the control and status register
* 2. Read the error location registers that corresponds to the number
* of errors reported
* 3. Invert the bit in the data
*/
numErrors = (regValue & REG_UMI_BCH_CTRL_STATUS_NB_CORR_ERROR) >> 20;
for (idx = 0; idx < numErrors; idx++) {
errorLocation =
REG_UMI_BCH_ERR_LOC_ADDR(idx) & REG_UMI_BCH_ERR_LOC_MASK;
/* Flip bit */
nand_bcm_umi_bch_ecc_flip_bit(datap, errorLocation);
}
/* Errors corrected */
return numErrors;
}
#endif
drivers/mtd/nand/nand_bcm_umi.h deleted 100644 → 0
View file @ 5ca7f415
/*****************************************************************************
* Copyright 2003 - 2009 Broadcom Corporation. All rights reserved.
*
* Unless you and Broadcom execute a separate written software license
* agreement governing use of this software, this software is licensed to you
* under the terms of the GNU General Public License version 2, available at
* http://www.broadcom.com/licenses/GPLv2.php (the "GPL").
*
* Notwithstanding the above, under no circumstances may you combine this
* software in any way with any other Broadcom software provided under a
* license other than the GPL, without Broadcom's express prior written
* consent.
*****************************************************************************/
#ifndef NAND_BCM_UMI_H
#define NAND_BCM_UMI_H
/* ---- Include Files ---------------------------------------------------- */
#include <mach/reg_umi.h>
#include <mach/reg_nand.h>
#include <cfg_global.h>
/* ---- Constants and Types ---------------------------------------------- */
#if (CFG_GLOBAL_CHIP_FAMILY == CFG_GLOBAL_CHIP_FAMILY_BCMRING)
#define NAND_ECC_BCH (CFG_GLOBAL_CHIP_REV > 0xA0)
#else
#define NAND_ECC_BCH 0
#endif
#define CFG_GLOBAL_NAND_ECC_BCH_NUM_BYTES 13
#if NAND_ECC_BCH
#ifdef BOOT0_BUILD
#define NAND_ECC_NUM_BYTES 13
#else
#define NAND_ECC_NUM_BYTES CFG_GLOBAL_NAND_ECC_BCH_NUM_BYTES
#endif
#else
#define NAND_ECC_NUM_BYTES 3
#endif
#define NAND_DATA_ACCESS_SIZE 512
/* ---- Variable Externs ------------------------------------------ */
/* ---- Function Prototypes --------------------------------------- */
int nand_bcm_umi_bch_correct_page(uint8_t *datap, uint8_t *readEccData,
int numEccBytes);
/* Check in device is ready */
static inline int nand_bcm_umi_dev_ready(void)
{
return REG_UMI_NAND_RCSR & REG_UMI_NAND_RCSR_RDY;
}
/* Wait until device is ready */
static inline void nand_bcm_umi_wait_till_ready(void)
{
while (nand_bcm_umi_dev_ready() == 0)
;
}
/* Enable Hamming ECC */
static inline void nand_bcm_umi_hamming_enable_hwecc(void)
{
/* disable and reset ECC, 512 byte page */
REG_UMI_NAND_ECC_CSR &= ~(REG_UMI_NAND_ECC_CSR_ECC_ENABLE |
REG_UMI_NAND_ECC_CSR_256BYTE);
/* enable ECC */
REG_UMI_NAND_ECC_CSR |= REG_UMI_NAND_ECC_CSR_ECC_ENABLE;
}
#if NAND_ECC_BCH
/* BCH ECC specifics */
#define ECC_BITS_PER_CORRECTABLE_BIT 13
/* Enable BCH Read ECC */
static inline void nand_bcm_umi_bch_enable_read_hwecc(void)
{
/* disable and reset ECC */
REG_UMI_BCH_CTRL_STATUS = REG_UMI_BCH_CTRL_STATUS_RD_ECC_VALID;
/* Turn on ECC */
REG_UMI_BCH_CTRL_STATUS = REG_UMI_BCH_CTRL_STATUS_ECC_RD_EN;
}
/* Enable BCH Write ECC */
static inline void nand_bcm_umi_bch_enable_write_hwecc(void)
{
/* disable and reset ECC */
REG_UMI_BCH_CTRL_STATUS = REG_UMI_BCH_CTRL_STATUS_WR_ECC_VALID;
/* Turn on ECC */
REG_UMI_BCH_CTRL_STATUS = REG_UMI_BCH_CTRL_STATUS_ECC_WR_EN;
}
/* Config number of BCH ECC bytes */
static inline void nand_bcm_umi_bch_config_ecc(uint8_t numEccBytes)
{
uint32_t nValue;
uint32_t tValue;
uint32_t kValue;
uint32_t numBits = numEccBytes * 8;
/* disable and reset ECC */
REG_UMI_BCH_CTRL_STATUS =
REG_UMI_BCH_CTRL_STATUS_WR_ECC_VALID |
REG_UMI_BCH_CTRL_STATUS_RD_ECC_VALID;
/* Every correctible bit requires 13 ECC bits */
tValue = (uint32_t) (numBits / ECC_BITS_PER_CORRECTABLE_BIT);
/* Total data in number of bits for generating and computing BCH ECC */
nValue = (NAND_DATA_ACCESS_SIZE + numEccBytes) * 8;
/* K parameter is used internally. K = N - (T * 13) */
kValue = nValue - (tValue * ECC_BITS_PER_CORRECTABLE_BIT);
/* Write the settings */
REG_UMI_BCH_N = nValue;
REG_UMI_BCH_T = tValue;
REG_UMI_BCH_K = kValue;
}
/* Pause during ECC read calculation to skip bytes in OOB */
static inline void nand_bcm_umi_bch_pause_read_ecc_calc(void)
{
REG_UMI_BCH_CTRL_STATUS =
REG_UMI_BCH_CTRL_STATUS_ECC_RD_EN |
REG_UMI_BCH_CTRL_STATUS_PAUSE_ECC_DEC;
}
/* Resume during ECC read calculation after skipping bytes in OOB */
static inline void nand_bcm_umi_bch_resume_read_ecc_calc(void)
{
REG_UMI_BCH_CTRL_STATUS = REG_UMI_BCH_CTRL_STATUS_ECC_RD_EN;
}
/* Poll read ECC calc to check when hardware completes */
static inline uint32_t nand_bcm_umi_bch_poll_read_ecc_calc(void)
{
uint32_t regVal;
do {
/* wait for ECC to be valid */
regVal = REG_UMI_BCH_CTRL_STATUS;
} while ((regVal & REG_UMI_BCH_CTRL_STATUS_RD_ECC_VALID) == 0);
return regVal;
}
/* Poll write ECC calc to check when hardware completes */
static inline void nand_bcm_umi_bch_poll_write_ecc_calc(void)
{
/* wait for ECC to be valid */
while ((REG_UMI_BCH_CTRL_STATUS & REG_UMI_BCH_CTRL_STATUS_WR_ECC_VALID)
== 0)
;
}
/* Read the OOB and ECC, for kernel write OOB to a buffer */
#if defined(__KERNEL__) && !defined(STANDALONE)
static inline void nand_bcm_umi_bch_read_oobEcc(uint32_t pageSize,
uint8_t *eccCalc, int numEccBytes, uint8_t *oobp)
#else
static inline void nand_bcm_umi_bch_read_oobEcc(uint32_t pageSize,
uint8_t *eccCalc, int numEccBytes)
#endif
{
int eccPos = 0;
int numToRead = 16; /* There are 16 bytes per sector in the OOB */
/* ECC is already paused when this function is called */
if (pageSize != NAND_DATA_ACCESS_SIZE) {
/* skip BI */
#if defined(__KERNEL__) && !defined(STANDALONE)
*oobp++ = REG_NAND_DATA8;
#else
REG_NAND_DATA8;
#endif
numToRead--;
}
while (numToRead > numEccBytes) {
/* skip free oob region */
#if defined(__KERNEL__) && !defined(STANDALONE)
*oobp++ = REG_NAND_DATA8;
#else
REG_NAND_DATA8;
#endif
numToRead--;
}
if (pageSize == NAND_DATA_ACCESS_SIZE) {
/* read ECC bytes before BI */
nand_bcm_umi_bch_resume_read_ecc_calc();
while (numToRead > 11) {
#if defined(__KERNEL__) && !defined(STANDALONE)
*oobp = REG_NAND_DATA8;
eccCalc[eccPos++] = *oobp;
oobp++;
#else
eccCalc[eccPos++] = REG_NAND_DATA8;
#endif
numToRead--;
}
nand_bcm_umi_bch_pause_read_ecc_calc();
if (numToRead == 11) {
/* read BI */
#if defined(__KERNEL__) && !defined(STANDALONE)
*oobp++ = REG_NAND_DATA8;
#else
REG_NAND_DATA8;
#endif
numToRead--;
}
}
/* read ECC bytes */
nand_bcm_umi_bch_resume_read_ecc_calc();
while (numToRead) {
#if defined(__KERNEL__) && !defined(STANDALONE)
*oobp = REG_NAND_DATA8;
eccCalc[eccPos++] = *oobp;
oobp++;
#else
eccCalc[eccPos++] = REG_NAND_DATA8;
#endif
numToRead--;
}
}
/* Helper function to write ECC */
static inline void NAND_BCM_UMI_ECC_WRITE(int numEccBytes, int eccBytePos,
uint8_t *oobp, uint8_t eccVal)
{
if (eccBytePos <= numEccBytes)
*oobp = eccVal;
}
/* Write OOB with ECC */
static inline void nand_bcm_umi_bch_write_oobEcc(uint32_t pageSize,
uint8_t *oobp, int numEccBytes)
{
uint32_t eccVal = 0xffffffff;
/* wait for write ECC to be valid */
nand_bcm_umi_bch_poll_write_ecc_calc();
/*
** Get the hardware ecc from the 32-bit result registers.
** Read after 512 byte accesses. Format B3B2B1B0
** where B3 = ecc3, etc.
*/
if (pageSize == NAND_DATA_ACCESS_SIZE) {
/* Now fill in the ECC bytes */
if (numEccBytes >= 13)
eccVal = REG_UMI_BCH_WR_ECC_3;
/* Usually we skip CM in oob[0,1] */
NAND_BCM_UMI_ECC_WRITE(numEccBytes, 15, &oobp[0],
(eccVal >> 16) & 0xff);
NAND_BCM_UMI_ECC_WRITE(numEccBytes, 14, &oobp[1],
(eccVal >> 8) & 0xff);
/* Write ECC in oob[2,3,4] */
NAND_BCM_UMI_ECC_WRITE(numEccBytes, 13, &oobp[2],
eccVal & 0xff); /* ECC 12 */
if (numEccBytes >= 9)
eccVal = REG_UMI_BCH_WR_ECC_2;
NAND_BCM_UMI_ECC_WRITE(numEccBytes, 12, &oobp[3],
(eccVal >> 24) & 0xff); /* ECC11 */
NAND_BCM_UMI_ECC_WRITE(numEccBytes, 11, &oobp[4],
(eccVal >> 16) & 0xff); /* ECC10 */
/* Always Skip BI in oob[5] */
} else {
/* Always Skip BI in oob[0] */
/* Now fill in the ECC bytes */
if (numEccBytes >= 13)
eccVal = REG_UMI_BCH_WR_ECC_3;
/* Usually skip CM in oob[1,2] */
NAND_BCM_UMI_ECC_WRITE(numEccBytes, 15, &oobp[1],
(eccVal >> 16) & 0xff);
NAND_BCM_UMI_ECC_WRITE(numEccBytes, 14, &oobp[2],
(eccVal >> 8) & 0xff);
/* Write ECC in oob[3-15] */
NAND_BCM_UMI_ECC_WRITE(numEccBytes, 13, &oobp[3],
eccVal & 0xff); /* ECC12 */
if (numEccBytes >= 9)
eccVal = REG_UMI_BCH_WR_ECC_2;
NAND_BCM_UMI_ECC_WRITE(numEccBytes, 12, &oobp[4],
(eccVal >> 24) & 0xff); /* ECC11 */
NAND_BCM_UMI_ECC_WRITE(numEccBytes, 11, &oobp[5],
(eccVal >> 16) & 0xff); /* ECC10 */
}
/* Fill in the remainder of ECC locations */
NAND_BCM_UMI_ECC_WRITE(numEccBytes, 10, &oobp[6],
(eccVal >> 8) & 0xff); /* ECC9 */
NAND_BCM_UMI_ECC_WRITE(numEccBytes, 9, &oobp[7],
eccVal & 0xff); /* ECC8 */
if (numEccBytes >= 5)
eccVal = REG_UMI_BCH_WR_ECC_1;
NAND_BCM_UMI_ECC_WRITE(numEccBytes, 8, &oobp[8],
(eccVal >> 24) & 0xff); /* ECC7 */
NAND_BCM_UMI_ECC_WRITE(numEccBytes, 7, &oobp[9],
(eccVal >> 16) & 0xff); /* ECC6 */
NAND_BCM_UMI_ECC_WRITE(numEccBytes, 6, &oobp[10],
(eccVal >> 8) & 0xff); /* ECC5 */
NAND_BCM_UMI_ECC_WRITE(numEccBytes, 5, &oobp[11],
eccVal & 0xff); /* ECC4 */
if (numEccBytes >= 1)
eccVal = REG_UMI_BCH_WR_ECC_0;
NAND_BCM_UMI_ECC_WRITE(numEccBytes, 4, &oobp[12],
(eccVal >> 24) & 0xff); /* ECC3 */
NAND_BCM_UMI_ECC_WRITE(numEccBytes, 3, &oobp[13],
(eccVal >> 16) & 0xff); /* ECC2 */
NAND_BCM_UMI_ECC_WRITE(numEccBytes, 2, &oobp[14],
(eccVal >> 8) & 0xff); /* ECC1 */
NAND_BCM_UMI_ECC_WRITE(numEccBytes, 1, &oobp[15],
eccVal & 0xff); /* ECC0 */
}
#endif
#endif /* NAND_BCM_UMI_H */
Markdown is supported
0% or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment
GitLab Nexedi Edition | About GitLab | About Nexedi | 沪ICP备2021021310号-2 | 沪ICP备2021021310号-7