Commit b4c9c1a7 authored by Guenter Roeck's avatar Guenter Roeck

hwmon: Driver for TI ADC128D818

ADC128D818 is a System Monitor with Temperature Sensor. It is similar to LM80
and LM96080, but has 16 bit wide sensor registers and no fan speed monitoring.
Signed-off-by: default avatarGuenter Roeck <linux@roeck-us.net>
parent ebf5e877
Kernel driver adc128d818
========================
Supported chips:
* Texas Instruments ADC818D818
Prefix: 'adc818d818'
Addresses scanned: I2C 0x1d, 0x1e, 0x1f, 0x2d, 0x2e, 0x2f
Datasheet: Publicly available at the TI website
http://www.ti.com/
Author: Guenter Roeck
Description
-----------
This driver implements support for the Texas Instruments ADC128D818.
It is described as 'ADC System Monitor with Temperature Sensor'.
The ADC128D818 implements one temperature sensor and seven voltage sensors.
Temperatures are measured in degrees Celsius. There is one set of limits.
When the HOT Temperature Limit is crossed, this will cause an alarm that will
be reasserted until the temperature drops below the HOT Hysteresis.
Measurements are guaranteed between -55 and +125 degrees. The temperature
measurement has a resolution of 0.5 degrees; the limits have a resolution
of 1 degree.
Voltage sensors (also known as IN sensors) report their values in volts.
An alarm is triggered if the voltage has crossed a programmable minimum
or maximum limit. Note that minimum in this case always means 'closest to
zero'; this is important for negative voltage measurements. All voltage
inputs can measure voltages between 0 and 2.55 volts, with a resolution
of 0.625 mV.
If an alarm triggers, it will remain triggered until the hardware register
is read at least once. This means that the cause for the alarm may
already have disappeared by the time the alarm is read. The driver
caches the alarm status for each sensor until it is at least reported
once, to ensure that alarms are reported to user space.
The ADC128D818 only updates its values approximately once per second;
reading it more often will do no harm, but will return 'old' values.
In addition to the scanned address list, the chip can also be configured for
addresses 0x35 to 0x37. Those addresses are not scanned. You have to instantiate
the driver explicitly if the chip is configured for any of those addresses in
your system.
...@@ -1277,6 +1277,16 @@ config SENSORS_SMM665 ...@@ -1277,6 +1277,16 @@ config SENSORS_SMM665
This driver can also be built as a module. If so, the module will This driver can also be built as a module. If so, the module will
be called smm665. be called smm665.
config SENSORS_ADC128D818
tristate "Texas Instruments ADC128D818"
depends on I2C
help
If you say yes here you get support for the Texas Instruments
ADC128D818 System Monitor with Temperature Sensor chip.
This driver can also be built as a module. If so, the module
will be called adc128d818.
config SENSORS_ADS1015 config SENSORS_ADS1015
tristate "Texas Instruments ADS1015" tristate "Texas Instruments ADS1015"
depends on I2C depends on I2C
......
...@@ -25,6 +25,7 @@ obj-$(CONFIG_SENSORS_ABITUGURU3)+= abituguru3.o ...@@ -25,6 +25,7 @@ obj-$(CONFIG_SENSORS_ABITUGURU3)+= abituguru3.o
obj-$(CONFIG_SENSORS_AD7314) += ad7314.o obj-$(CONFIG_SENSORS_AD7314) += ad7314.o
obj-$(CONFIG_SENSORS_AD7414) += ad7414.o obj-$(CONFIG_SENSORS_AD7414) += ad7414.o
obj-$(CONFIG_SENSORS_AD7418) += ad7418.o obj-$(CONFIG_SENSORS_AD7418) += ad7418.o
obj-$(CONFIG_SENSORS_ADC128D818) += adc128d818.o
obj-$(CONFIG_SENSORS_ADCXX) += adcxx.o obj-$(CONFIG_SENSORS_ADCXX) += adcxx.o
obj-$(CONFIG_SENSORS_ADM1021) += adm1021.o obj-$(CONFIG_SENSORS_ADM1021) += adm1021.o
obj-$(CONFIG_SENSORS_ADM1025) += adm1025.o obj-$(CONFIG_SENSORS_ADM1025) += adm1025.o
......
/*
* Driver for TI ADC128D818 System Monitor with Temperature Sensor
*
* Copyright (c) 2014 Guenter Roeck
*
* Derived from lm80.c
* Copyright (C) 1998, 1999 Frodo Looijaard <frodol@dds.nl>
* and Philip Edelbrock <phil@netroedge.com>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*/
#include <linux/module.h>
#include <linux/slab.h>
#include <linux/jiffies.h>
#include <linux/i2c.h>
#include <linux/hwmon.h>
#include <linux/hwmon-sysfs.h>
#include <linux/err.h>
#include <linux/regulator/consumer.h>
#include <linux/mutex.h>
/* Addresses to scan
* The chip also supports addresses 0x35..0x37. Don't scan those addresses
* since they are also used by some EEPROMs, which may result in false
* positives.
*/
static const unsigned short normal_i2c[] = {
0x1d, 0x1e, 0x1f, 0x2d, 0x2e, 0x2f, I2C_CLIENT_END };
/* registers */
#define ADC128_REG_IN_MAX(nr) (0x2a + (nr) * 2)
#define ADC128_REG_IN_MIN(nr) (0x2b + (nr) * 2)
#define ADC128_REG_IN(nr) (0x20 + (nr))
#define ADC128_REG_TEMP 0x27
#define ADC128_REG_TEMP_MAX 0x38
#define ADC128_REG_TEMP_HYST 0x39
#define ADC128_REG_CONFIG 0x00
#define ADC128_REG_ALARM 0x01
#define ADC128_REG_MASK 0x03
#define ADC128_REG_CONV_RATE 0x07
#define ADC128_REG_ONESHOT 0x09
#define ADC128_REG_SHUTDOWN 0x0a
#define ADC128_REG_CONFIG_ADV 0x0b
#define ADC128_REG_BUSY_STATUS 0x0c
#define ADC128_REG_MAN_ID 0x3e
#define ADC128_REG_DEV_ID 0x3f
struct adc128_data {
struct i2c_client *client;
struct regulator *regulator;
int vref; /* Reference voltage in mV */
struct mutex update_lock;
bool valid; /* true if following fields are valid */
unsigned long last_updated; /* In jiffies */
u16 in[3][7]; /* Register value, normalized to 12 bit
* 0: input voltage
* 1: min limit
* 2: max limit
*/
s16 temp[3]; /* Register value, normalized to 9 bit
* 0: sensor 1: limit 2: hyst
*/
u8 alarms; /* alarm register value */
};
static struct adc128_data *adc128_update_device(struct device *dev)
{
struct adc128_data *data = dev_get_drvdata(dev);
struct i2c_client *client = data->client;
struct adc128_data *ret = data;
int i, rv;
mutex_lock(&data->update_lock);
if (time_after(jiffies, data->last_updated + HZ) || !data->valid) {
for (i = 0; i < 7; i++) {
rv = i2c_smbus_read_word_swapped(client,
ADC128_REG_IN(i));
if (rv < 0)
goto abort;
data->in[0][i] = rv >> 4;
rv = i2c_smbus_read_byte_data(client,
ADC128_REG_IN_MIN(i));
if (rv < 0)
goto abort;
data->in[1][i] = rv << 4;
rv = i2c_smbus_read_byte_data(client,
ADC128_REG_IN_MAX(i));
if (rv < 0)
goto abort;
data->in[2][i] = rv << 4;
}
rv = i2c_smbus_read_word_swapped(client, ADC128_REG_TEMP);
if (rv < 0)
goto abort;
data->temp[0] = rv >> 7;
rv = i2c_smbus_read_byte_data(client, ADC128_REG_TEMP_MAX);
if (rv < 0)
goto abort;
data->temp[1] = rv << 1;
rv = i2c_smbus_read_byte_data(client, ADC128_REG_TEMP_HYST);
if (rv < 0)
goto abort;
data->temp[2] = rv << 1;
rv = i2c_smbus_read_byte_data(client, ADC128_REG_ALARM);
if (rv < 0)
goto abort;
data->alarms |= rv;
data->last_updated = jiffies;
data->valid = true;
}
goto done;
abort:
ret = ERR_PTR(rv);
data->valid = false;
done:
mutex_unlock(&data->update_lock);
return ret;
}
static ssize_t adc128_show_in(struct device *dev, struct device_attribute *attr,
char *buf)
{
struct adc128_data *data = adc128_update_device(dev);
int index = to_sensor_dev_attr_2(attr)->index;
int nr = to_sensor_dev_attr_2(attr)->nr;
int val;
if (IS_ERR(data))
return PTR_ERR(data);
val = DIV_ROUND_CLOSEST(data->in[index][nr] * data->vref, 4095);
return sprintf(buf, "%d\n", val);
}
static ssize_t adc128_set_in(struct device *dev, struct device_attribute *attr,
const char *buf, size_t count)
{
struct adc128_data *data = dev_get_drvdata(dev);
int index = to_sensor_dev_attr_2(attr)->index;
int nr = to_sensor_dev_attr_2(attr)->nr;
u8 reg, regval;
long val;
int err;
err = kstrtol(buf, 10, &val);
if (err < 0)
return err;
mutex_lock(&data->update_lock);
/* 10 mV LSB on limit registers */
regval = clamp_val(DIV_ROUND_CLOSEST(val, 10), 0, 255);
data->in[index][nr] = regval << 4;
reg = index == 1 ? ADC128_REG_IN_MIN(nr) : ADC128_REG_IN_MAX(nr);
i2c_smbus_write_byte_data(data->client, reg, regval);
mutex_unlock(&data->update_lock);
return count;
}
static ssize_t adc128_show_temp(struct device *dev,
struct device_attribute *attr, char *buf)
{
struct adc128_data *data = adc128_update_device(dev);
int index = to_sensor_dev_attr(attr)->index;
int temp;
if (IS_ERR(data))
return PTR_ERR(data);
temp = (data->temp[index] << 7) >> 7; /* sign extend */
return sprintf(buf, "%d\n", temp * 500);/* 0.5 degrees C resolution */
}
static ssize_t adc128_set_temp(struct device *dev,
struct device_attribute *attr,
const char *buf, size_t count)
{
struct adc128_data *data = dev_get_drvdata(dev);
int index = to_sensor_dev_attr(attr)->index;
long val;
int err;
s8 regval;
err = kstrtol(buf, 10, &val);
if (err < 0)
return err;
mutex_lock(&data->update_lock);
regval = clamp_val(DIV_ROUND_CLOSEST(val, 1000), -128, 127);
data->temp[index] = regval << 1;
i2c_smbus_write_byte_data(data->client,
index == 1 ? ADC128_REG_TEMP_MAX
: ADC128_REG_TEMP_HYST,
regval);
mutex_unlock(&data->update_lock);
return count;
}
static ssize_t adc128_show_alarm(struct device *dev,
struct device_attribute *attr, char *buf)
{
struct adc128_data *data = adc128_update_device(dev);
int mask = 1 << to_sensor_dev_attr(attr)->index;
u8 alarms;
if (IS_ERR(data))
return PTR_ERR(data);
/*
* Clear an alarm after reporting it to user space. If it is still
* active, the next update sequence will set the alarm bit again.
*/
alarms = data->alarms;
data->alarms &= ~mask;
return sprintf(buf, "%u\n", !!(alarms & mask));
}
static SENSOR_DEVICE_ATTR_2(in0_input, S_IWUSR | S_IRUGO,
adc128_show_in, adc128_set_in, 0, 0);
static SENSOR_DEVICE_ATTR_2(in0_min, S_IWUSR | S_IRUGO,
adc128_show_in, adc128_set_in, 0, 1);
static SENSOR_DEVICE_ATTR_2(in0_max, S_IWUSR | S_IRUGO,
adc128_show_in, adc128_set_in, 0, 2);
static SENSOR_DEVICE_ATTR_2(in1_input, S_IWUSR | S_IRUGO,
adc128_show_in, adc128_set_in, 1, 0);
static SENSOR_DEVICE_ATTR_2(in1_min, S_IWUSR | S_IRUGO,
adc128_show_in, adc128_set_in, 1, 1);
static SENSOR_DEVICE_ATTR_2(in1_max, S_IWUSR | S_IRUGO,
adc128_show_in, adc128_set_in, 1, 2);
static SENSOR_DEVICE_ATTR_2(in2_input, S_IWUSR | S_IRUGO,
adc128_show_in, adc128_set_in, 2, 0);
static SENSOR_DEVICE_ATTR_2(in2_min, S_IWUSR | S_IRUGO,
adc128_show_in, adc128_set_in, 2, 1);
static SENSOR_DEVICE_ATTR_2(in2_max, S_IWUSR | S_IRUGO,
adc128_show_in, adc128_set_in, 2, 2);
static SENSOR_DEVICE_ATTR_2(in3_input, S_IWUSR | S_IRUGO,
adc128_show_in, adc128_set_in, 3, 0);
static SENSOR_DEVICE_ATTR_2(in3_min, S_IWUSR | S_IRUGO,
adc128_show_in, adc128_set_in, 3, 1);
static SENSOR_DEVICE_ATTR_2(in3_max, S_IWUSR | S_IRUGO,
adc128_show_in, adc128_set_in, 3, 2);
static SENSOR_DEVICE_ATTR_2(in4_input, S_IWUSR | S_IRUGO,
adc128_show_in, adc128_set_in, 4, 0);
static SENSOR_DEVICE_ATTR_2(in4_min, S_IWUSR | S_IRUGO,
adc128_show_in, adc128_set_in, 4, 1);
static SENSOR_DEVICE_ATTR_2(in4_max, S_IWUSR | S_IRUGO,
adc128_show_in, adc128_set_in, 4, 2);
static SENSOR_DEVICE_ATTR_2(in5_input, S_IWUSR | S_IRUGO,
adc128_show_in, adc128_set_in, 5, 0);
static SENSOR_DEVICE_ATTR_2(in5_min, S_IWUSR | S_IRUGO,
adc128_show_in, adc128_set_in, 5, 1);
static SENSOR_DEVICE_ATTR_2(in5_max, S_IWUSR | S_IRUGO,
adc128_show_in, adc128_set_in, 5, 2);
static SENSOR_DEVICE_ATTR_2(in6_input, S_IWUSR | S_IRUGO,
adc128_show_in, adc128_set_in, 6, 0);
static SENSOR_DEVICE_ATTR_2(in6_min, S_IWUSR | S_IRUGO,
adc128_show_in, adc128_set_in, 6, 1);
static SENSOR_DEVICE_ATTR_2(in6_max, S_IWUSR | S_IRUGO,
adc128_show_in, adc128_set_in, 6, 2);
static SENSOR_DEVICE_ATTR(temp1_input, S_IRUGO, adc128_show_temp, NULL, 0);
static SENSOR_DEVICE_ATTR(temp1_max, S_IWUSR | S_IRUGO,
adc128_show_temp, adc128_set_temp, 1);
static SENSOR_DEVICE_ATTR(temp1_max_hyst, S_IWUSR | S_IRUGO,
adc128_show_temp, adc128_set_temp, 2);
static SENSOR_DEVICE_ATTR(in0_alarm, S_IRUGO, adc128_show_alarm, NULL, 0);
static SENSOR_DEVICE_ATTR(in1_alarm, S_IRUGO, adc128_show_alarm, NULL, 1);
static SENSOR_DEVICE_ATTR(in2_alarm, S_IRUGO, adc128_show_alarm, NULL, 2);
static SENSOR_DEVICE_ATTR(in3_alarm, S_IRUGO, adc128_show_alarm, NULL, 3);
static SENSOR_DEVICE_ATTR(in4_alarm, S_IRUGO, adc128_show_alarm, NULL, 4);
static SENSOR_DEVICE_ATTR(in5_alarm, S_IRUGO, adc128_show_alarm, NULL, 5);
static SENSOR_DEVICE_ATTR(in6_alarm, S_IRUGO, adc128_show_alarm, NULL, 6);
static SENSOR_DEVICE_ATTR(temp1_max_alarm, S_IRUGO, adc128_show_alarm, NULL, 7);
static struct attribute *adc128_attrs[] = {
&sensor_dev_attr_in0_min.dev_attr.attr,
&sensor_dev_attr_in1_min.dev_attr.attr,
&sensor_dev_attr_in2_min.dev_attr.attr,
&sensor_dev_attr_in3_min.dev_attr.attr,
&sensor_dev_attr_in4_min.dev_attr.attr,
&sensor_dev_attr_in5_min.dev_attr.attr,
&sensor_dev_attr_in6_min.dev_attr.attr,
&sensor_dev_attr_in0_max.dev_attr.attr,
&sensor_dev_attr_in1_max.dev_attr.attr,
&sensor_dev_attr_in2_max.dev_attr.attr,
&sensor_dev_attr_in3_max.dev_attr.attr,
&sensor_dev_attr_in4_max.dev_attr.attr,
&sensor_dev_attr_in5_max.dev_attr.attr,
&sensor_dev_attr_in6_max.dev_attr.attr,
&sensor_dev_attr_in0_input.dev_attr.attr,
&sensor_dev_attr_in1_input.dev_attr.attr,
&sensor_dev_attr_in2_input.dev_attr.attr,
&sensor_dev_attr_in3_input.dev_attr.attr,
&sensor_dev_attr_in4_input.dev_attr.attr,
&sensor_dev_attr_in5_input.dev_attr.attr,
&sensor_dev_attr_in6_input.dev_attr.attr,
&sensor_dev_attr_temp1_input.dev_attr.attr,
&sensor_dev_attr_temp1_max.dev_attr.attr,
&sensor_dev_attr_temp1_max_hyst.dev_attr.attr,
&sensor_dev_attr_in0_alarm.dev_attr.attr,
&sensor_dev_attr_in1_alarm.dev_attr.attr,
&sensor_dev_attr_in2_alarm.dev_attr.attr,
&sensor_dev_attr_in3_alarm.dev_attr.attr,
&sensor_dev_attr_in4_alarm.dev_attr.attr,
&sensor_dev_attr_in5_alarm.dev_attr.attr,
&sensor_dev_attr_in6_alarm.dev_attr.attr,
&sensor_dev_attr_temp1_max_alarm.dev_attr.attr,
NULL
};
ATTRIBUTE_GROUPS(adc128);
static int adc128_detect(struct i2c_client *client, struct i2c_board_info *info)
{
int man_id, dev_id;
if (!i2c_check_functionality(client->adapter,
I2C_FUNC_SMBUS_BYTE_DATA |
I2C_FUNC_SMBUS_WORD_DATA))
return -ENODEV;
man_id = i2c_smbus_read_byte_data(client, ADC128_REG_MAN_ID);
dev_id = i2c_smbus_read_byte_data(client, ADC128_REG_DEV_ID);
if (man_id != 0x01 || dev_id != 0x09)
return -ENODEV;
/* Check unused bits for confirmation */
if (i2c_smbus_read_byte_data(client, ADC128_REG_CONFIG) & 0xf4)
return -ENODEV;
if (i2c_smbus_read_byte_data(client, ADC128_REG_CONV_RATE) & 0xfe)
return -ENODEV;
if (i2c_smbus_read_byte_data(client, ADC128_REG_ONESHOT) & 0xfe)
return -ENODEV;
if (i2c_smbus_read_byte_data(client, ADC128_REG_SHUTDOWN) & 0xfe)
return -ENODEV;
if (i2c_smbus_read_byte_data(client, ADC128_REG_CONFIG_ADV) & 0xf8)
return -ENODEV;
if (i2c_smbus_read_byte_data(client, ADC128_REG_BUSY_STATUS) & 0xfc)
return -ENODEV;
strlcpy(info->type, "adc128d818", I2C_NAME_SIZE);
return 0;
}
static int adc128_init_client(struct adc128_data *data)
{
struct i2c_client *client = data->client;
int err;
/*
* Reset chip to defaults.
* This makes most other initializations unnecessary.
*/
err = i2c_smbus_write_byte_data(client, ADC128_REG_CONFIG, 0x80);
if (err)
return err;
/* Start monitoring */
err = i2c_smbus_write_byte_data(client, ADC128_REG_CONFIG, 0x01);
if (err)
return err;
/* If external vref is selected, configure the chip to use it */
if (data->regulator) {
err = i2c_smbus_write_byte_data(client,
ADC128_REG_CONFIG_ADV, 0x01);
if (err)
return err;
}
return 0;
}
static int adc128_probe(struct i2c_client *client,
const struct i2c_device_id *id)
{
struct device *dev = &client->dev;
struct regulator *regulator;
struct device *hwmon_dev;
struct adc128_data *data;
int err, vref;
data = devm_kzalloc(dev, sizeof(struct adc128_data), GFP_KERNEL);
if (!data)
return -ENOMEM;
/* vref is optional. If specified, is used as chip reference voltage */
regulator = devm_regulator_get_optional(dev, "vref");
if (!IS_ERR(regulator)) {
data->regulator = regulator;
err = regulator_enable(regulator);
if (err < 0)
return err;
vref = regulator_get_voltage(regulator);
if (vref < 0) {
err = vref;
goto error;
}
data->vref = DIV_ROUND_CLOSEST(vref, 1000);
} else {
data->vref = 2560; /* 2.56V, in mV */
}
data->client = client;
i2c_set_clientdata(client, data);
mutex_init(&data->update_lock);
/* Initialize the chip */
err = adc128_init_client(data);
if (err < 0)
goto error;
hwmon_dev = devm_hwmon_device_register_with_groups(dev, client->name,
data, adc128_groups);
if (IS_ERR(hwmon_dev)) {
err = PTR_ERR(hwmon_dev);
goto error;
}
return 0;
error:
if (data->regulator)
regulator_disable(data->regulator);
return err;
}
static int adc128_remove(struct i2c_client *client)
{
struct adc128_data *data = i2c_get_clientdata(client);
if (data->regulator)
regulator_disable(data->regulator);
return 0;
}
static const struct i2c_device_id adc128_id[] = {
{ "adc128d818", 0 },
{ }
};
MODULE_DEVICE_TABLE(i2c, adc128_id);
static struct i2c_driver adc128_driver = {
.class = I2C_CLASS_HWMON,
.driver = {
.name = "adc128d818",
},
.probe = adc128_probe,
.remove = adc128_remove,
.id_table = adc128_id,
.detect = adc128_detect,
.address_list = normal_i2c,
};
module_i2c_driver(adc128_driver);
MODULE_AUTHOR("Guenter Roeck");
MODULE_DESCRIPTION("Driver for ADC128D818");
MODULE_LICENSE("GPL");
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment