Commit bf931a01 authored by Linus Torvalds's avatar Linus Torvalds

Merge branch 'next-spi' of git://git.secretlab.ca/git/linux-2.6

* 'next-spi' of git://git.secretlab.ca/git/linux-2.6:
  spi: spi_txx9.c: use resource_size()
  spi: spi_sh_sci.c: use resource_size()
  spi: spi_mpc8xxx.c: use resource_size()
  spi: spi_bfin5xx.c: use resource_size()
  spi: atmel_spi.c: use resource_size()
  spi: Add s3c64xx SPI Controller driver
  atmel_spi: fix dma addr calculation for len > BUFFER_SIZE
  spi_s3c24xx: add FIQ pseudo-DMA support
  spi: controller driver for Designware SPI core
  spidev: add proper section markers
  spidev: use DECLARE_BITMAP instead of declaring the array
parents 4e46aa08 d53342bf
......@@ -18,6 +18,8 @@ struct s3c2410_spi_info {
unsigned int num_cs; /* total chipselects */
int bus_num; /* bus number to use. */
unsigned int use_fiq:1; /* use fiq */
void (*gpio_setup)(struct s3c2410_spi_info *spi, int enable);
void (*set_cs)(struct s3c2410_spi_info *spi, int cs, int pol);
};
......
......@@ -216,6 +216,17 @@ config SPI_S3C24XX
help
SPI driver for Samsung S3C24XX series ARM SoCs
config SPI_S3C24XX_FIQ
bool "S3C24XX driver with FIQ pseudo-DMA"
depends on SPI_S3C24XX
select FIQ
help
Enable FIQ support for the S3C24XX SPI driver to provide pseudo
DMA by using the fast-interrupt request framework, This allows
the driver to get DMA-like performance when there are either
no free DMA channels, or when doing transfers that required both
TX and RX data paths.
config SPI_S3C24XX_GPIO
tristate "Samsung S3C24XX series SPI by GPIO"
depends on ARCH_S3C2410 && EXPERIMENTAL
......@@ -226,6 +237,13 @@ config SPI_S3C24XX_GPIO
the inbuilt hardware cannot provide the transfer mode, or
where the board is using non hardware connected pins.
config SPI_S3C64XX
tristate "Samsung S3C64XX series type SPI"
depends on ARCH_S3C64XX && EXPERIMENTAL
select S3C64XX_DMA
help
SPI driver for Samsung S3C64XX and newer SoCs.
config SPI_SH_MSIOF
tristate "SuperH MSIOF SPI controller"
depends on SUPERH && HAVE_CLK
......@@ -289,6 +307,16 @@ config SPI_NUC900
# Add new SPI master controllers in alphabetical order above this line
#
config SPI_DESIGNWARE
bool "DesignWare SPI controller core support"
depends on SPI_MASTER
help
general driver for SPI controller core from DesignWare
config SPI_DW_PCI
tristate "PCI interface driver for DW SPI core"
depends on SPI_DESIGNWARE && PCI
#
# There are lots of SPI device types, with sensors and memory
# being probably the most widely used ones.
......
......@@ -16,6 +16,8 @@ obj-$(CONFIG_SPI_BFIN) += spi_bfin5xx.o
obj-$(CONFIG_SPI_BITBANG) += spi_bitbang.o
obj-$(CONFIG_SPI_AU1550) += au1550_spi.o
obj-$(CONFIG_SPI_BUTTERFLY) += spi_butterfly.o
obj-$(CONFIG_SPI_DESIGNWARE) += dw_spi.o
obj-$(CONFIG_SPI_DW_PCI) += dw_spi_pci.o
obj-$(CONFIG_SPI_GPIO) += spi_gpio.o
obj-$(CONFIG_SPI_IMX) += spi_imx.o
obj-$(CONFIG_SPI_LM70_LLP) += spi_lm70llp.o
......@@ -30,7 +32,8 @@ obj-$(CONFIG_SPI_MPC52xx) += mpc52xx_spi.o
obj-$(CONFIG_SPI_MPC8xxx) += spi_mpc8xxx.o
obj-$(CONFIG_SPI_PPC4xx) += spi_ppc4xx.o
obj-$(CONFIG_SPI_S3C24XX_GPIO) += spi_s3c24xx_gpio.o
obj-$(CONFIG_SPI_S3C24XX) += spi_s3c24xx.o
obj-$(CONFIG_SPI_S3C24XX) += spi_s3c24xx_hw.o
obj-$(CONFIG_SPI_S3C64XX) += spi_s3c64xx.o
obj-$(CONFIG_SPI_TXX9) += spi_txx9.o
obj-$(CONFIG_SPI_XILINX) += xilinx_spi.o
obj-$(CONFIG_SPI_XILINX_OF) += xilinx_spi_of.o
......@@ -39,6 +42,11 @@ obj-$(CONFIG_SPI_SH_SCI) += spi_sh_sci.o
obj-$(CONFIG_SPI_SH_MSIOF) += spi_sh_msiof.o
obj-$(CONFIG_SPI_STMP3XXX) += spi_stmp.o
obj-$(CONFIG_SPI_NUC900) += spi_nuc900.o
# special build for s3c24xx spi driver with fiq support
spi_s3c24xx_hw-y := spi_s3c24xx.o
spi_s3c24xx_hw-$(CONFIG_SPI_S3C24XX_FIQ) += spi_s3c24xx_fiq.o
# ... add above this line ...
# SPI protocol drivers (device/link on bus)
......
......@@ -189,14 +189,14 @@ static void atmel_spi_next_xfer_data(struct spi_master *master,
/* use scratch buffer only when rx or tx data is unspecified */
if (xfer->rx_buf)
*rx_dma = xfer->rx_dma + xfer->len - len;
*rx_dma = xfer->rx_dma + xfer->len - *plen;
else {
*rx_dma = as->buffer_dma;
if (len > BUFFER_SIZE)
len = BUFFER_SIZE;
}
if (xfer->tx_buf)
*tx_dma = xfer->tx_dma + xfer->len - len;
*tx_dma = xfer->tx_dma + xfer->len - *plen;
else {
*tx_dma = as->buffer_dma;
if (len > BUFFER_SIZE)
......@@ -788,7 +788,7 @@ static int __init atmel_spi_probe(struct platform_device *pdev)
spin_lock_init(&as->lock);
INIT_LIST_HEAD(&as->queue);
as->pdev = pdev;
as->regs = ioremap(regs->start, (regs->end - regs->start) + 1);
as->regs = ioremap(regs->start, resource_size(regs));
if (!as->regs)
goto out_free_buffer;
as->irq = irq;
......
This diff is collapsed.
/*
* mrst_spi_pci.c - PCI interface driver for DW SPI Core
*
* Copyright (c) 2009, Intel Corporation.
*
* This program is free software; you can redistribute it and/or modify it
* under the terms and conditions of the GNU General Public License,
* version 2, as published by the Free Software Foundation.
*
* This program is distributed in the hope it will be useful, but WITHOUT
* ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
* FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
* more details.
*
* You should have received a copy of the GNU General Public License along
* with this program; if not, write to the Free Software Foundation,
* Inc., 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
*/
#include <linux/interrupt.h>
#include <linux/pci.h>
#include <linux/spi/dw_spi.h>
#include <linux/spi/spi.h>
#define DRIVER_NAME "dw_spi_pci"
struct dw_spi_pci {
struct pci_dev *pdev;
struct dw_spi dws;
};
static int __devinit spi_pci_probe(struct pci_dev *pdev,
const struct pci_device_id *ent)
{
struct dw_spi_pci *dwpci;
struct dw_spi *dws;
int pci_bar = 0;
int ret;
printk(KERN_INFO "DW: found PCI SPI controller(ID: %04x:%04x)\n",
pdev->vendor, pdev->device);
ret = pci_enable_device(pdev);
if (ret)
return ret;
dwpci = kzalloc(sizeof(struct dw_spi_pci), GFP_KERNEL);
if (!dwpci) {
ret = -ENOMEM;
goto err_disable;
}
dwpci->pdev = pdev;
dws = &dwpci->dws;
/* Get basic io resource and map it */
dws->paddr = pci_resource_start(pdev, pci_bar);
dws->iolen = pci_resource_len(pdev, pci_bar);
ret = pci_request_region(pdev, pci_bar, dev_name(&pdev->dev));
if (ret)
goto err_kfree;
dws->regs = ioremap_nocache((unsigned long)dws->paddr,
pci_resource_len(pdev, pci_bar));
if (!dws->regs) {
ret = -ENOMEM;
goto err_release_reg;
}
dws->parent_dev = &pdev->dev;
dws->bus_num = 0;
dws->num_cs = 4;
dws->max_freq = 25000000; /* for Moorestwon */
dws->irq = pdev->irq;
ret = dw_spi_add_host(dws);
if (ret)
goto err_unmap;
/* PCI hook and SPI hook use the same drv data */
pci_set_drvdata(pdev, dwpci);
return 0;
err_unmap:
iounmap(dws->regs);
err_release_reg:
pci_release_region(pdev, pci_bar);
err_kfree:
kfree(dwpci);
err_disable:
pci_disable_device(pdev);
return ret;
}
static void __devexit spi_pci_remove(struct pci_dev *pdev)
{
struct dw_spi_pci *dwpci = pci_get_drvdata(pdev);
pci_set_drvdata(pdev, NULL);
iounmap(dwpci->dws.regs);
pci_release_region(pdev, 0);
kfree(dwpci);
pci_disable_device(pdev);
}
#ifdef CONFIG_PM
static int spi_suspend(struct pci_dev *pdev, pm_message_t state)
{
struct dw_spi_pci *dwpci = pci_get_drvdata(pdev);
int ret;
ret = dw_spi_suspend_host(&dwpci->dws);
if (ret)
return ret;
pci_save_state(pdev);
pci_disable_device(pdev);
pci_set_power_state(pdev, pci_choose_state(pdev, state));
return ret;
}
static int spi_resume(struct pci_dev *pdev)
{
struct dw_spi_pci *dwpci = pci_get_drvdata(pdev);
int ret;
pci_set_power_state(pdev, PCI_D0);
pci_restore_state(pdev);
ret = pci_enable_device(pdev);
if (ret)
return ret;
return dw_spi_resume_host(&dwpci->dws);
}
#else
#define spi_suspend NULL
#define spi_resume NULL
#endif
static const struct pci_device_id pci_ids[] __devinitdata = {
/* Intel Moorestown platform SPI controller 0 */
{ PCI_DEVICE(PCI_VENDOR_ID_INTEL, 0x0800) },
{},
};
static struct pci_driver dw_spi_driver = {
.name = DRIVER_NAME,
.id_table = pci_ids,
.probe = spi_pci_probe,
.remove = __devexit_p(spi_pci_remove),
.suspend = spi_suspend,
.resume = spi_resume,
};
static int __init mrst_spi_init(void)
{
return pci_register_driver(&dw_spi_driver);
}
static void __exit mrst_spi_exit(void)
{
pci_unregister_driver(&dw_spi_driver);
}
module_init(mrst_spi_init);
module_exit(mrst_spi_exit);
MODULE_AUTHOR("Feng Tang <feng.tang@intel.com>");
MODULE_DESCRIPTION("PCI interface driver for DW SPI Core");
MODULE_LICENSE("GPL v2");
......@@ -1294,7 +1294,7 @@ static int __init bfin_spi_probe(struct platform_device *pdev)
goto out_error_get_res;
}
drv_data->regs_base = ioremap(res->start, (res->end - res->start + 1));
drv_data->regs_base = ioremap(res->start, resource_size(res));
if (drv_data->regs_base == NULL) {
dev_err(dev, "Cannot map IO\n");
status = -ENXIO;
......
......@@ -1013,7 +1013,7 @@ mpc8xxx_spi_probe(struct device *dev, struct resource *mem, unsigned int irq)
init_completion(&mpc8xxx_spi->done);
mpc8xxx_spi->base = ioremap(mem->start, mem->end - mem->start + 1);
mpc8xxx_spi->base = ioremap(mem->start, resource_size(mem));
if (mpc8xxx_spi->base == NULL) {
ret = -ENOMEM;
goto err_ioremap;
......
/* linux/drivers/spi/spi_s3c24xx.c
*
* Copyright (c) 2006 Ben Dooks
* Copyright (c) 2006 Simtec Electronics
* Copyright 2006-2009 Simtec Electronics
* Ben Dooks <ben@simtec.co.uk>
*
* This program is free software; you can redistribute it and/or modify
......@@ -28,6 +28,11 @@
#include <plat/regs-spi.h>
#include <mach/spi.h>
#include <plat/fiq.h>
#include <asm/fiq.h>
#include "spi_s3c24xx_fiq.h"
/**
* s3c24xx_spi_devstate - per device data
* @hz: Last frequency calculated for @sppre field.
......@@ -42,6 +47,13 @@ struct s3c24xx_spi_devstate {
u8 sppre;
};
enum spi_fiq_mode {
FIQ_MODE_NONE = 0,
FIQ_MODE_TX = 1,
FIQ_MODE_RX = 2,
FIQ_MODE_TXRX = 3,
};
struct s3c24xx_spi {
/* bitbang has to be first */
struct spi_bitbang bitbang;
......@@ -52,6 +64,11 @@ struct s3c24xx_spi {
int len;
int count;
struct fiq_handler fiq_handler;
enum spi_fiq_mode fiq_mode;
unsigned char fiq_inuse;
unsigned char fiq_claimed;
void (*set_cs)(struct s3c2410_spi_info *spi,
int cs, int pol);
......@@ -67,6 +84,7 @@ struct s3c24xx_spi {
struct s3c2410_spi_info *pdata;
};
#define SPCON_DEFAULT (S3C2410_SPCON_MSTR | S3C2410_SPCON_SMOD_INT)
#define SPPIN_DEFAULT (S3C2410_SPPIN_KEEP)
......@@ -127,7 +145,7 @@ static int s3c24xx_spi_update_state(struct spi_device *spi,
}
if (spi->mode != cs->mode) {
u8 spcon = SPCON_DEFAULT;
u8 spcon = SPCON_DEFAULT | S3C2410_SPCON_ENSCK;
if (spi->mode & SPI_CPHA)
spcon |= S3C2410_SPCON_CPHA_FMTB;
......@@ -214,13 +232,196 @@ static inline unsigned int hw_txbyte(struct s3c24xx_spi *hw, int count)
return hw->tx ? hw->tx[count] : 0;
}
#ifdef CONFIG_SPI_S3C24XX_FIQ
/* Support for FIQ based pseudo-DMA to improve the transfer speed.
*
* This code uses the assembly helper in spi_s3c24xx_spi.S which is
* used by the FIQ core to move data between main memory and the peripheral
* block. Since this is code running on the processor, there is no problem
* with cache coherency of the buffers, so we can use any buffer we like.
*/
/**
* struct spi_fiq_code - FIQ code and header
* @length: The length of the code fragment, excluding this header.
* @ack_offset: The offset from @data to the word to place the IRQ ACK bit at.
* @data: The code itself to install as a FIQ handler.
*/
struct spi_fiq_code {
u32 length;
u32 ack_offset;
u8 data[0];
};
extern struct spi_fiq_code s3c24xx_spi_fiq_txrx;
extern struct spi_fiq_code s3c24xx_spi_fiq_tx;
extern struct spi_fiq_code s3c24xx_spi_fiq_rx;
/**
* ack_bit - turn IRQ into IRQ acknowledgement bit
* @irq: The interrupt number
*
* Returns the bit to write to the interrupt acknowledge register.
*/
static inline u32 ack_bit(unsigned int irq)
{
return 1 << (irq - IRQ_EINT0);
}
/**
* s3c24xx_spi_tryfiq - attempt to claim and setup FIQ for transfer
* @hw: The hardware state.
*
* Claim the FIQ handler (only one can be active at any one time) and
* then setup the correct transfer code for this transfer.
*
* This call updates all the necessary state information if sucessful,
* so the caller does not need to do anything more than start the transfer
* as normal, since the IRQ will have been re-routed to the FIQ handler.
*/
void s3c24xx_spi_tryfiq(struct s3c24xx_spi *hw)
{
struct pt_regs regs;
enum spi_fiq_mode mode;
struct spi_fiq_code *code;
int ret;
if (!hw->fiq_claimed) {
/* try and claim fiq if we haven't got it, and if not
* then return and simply use another transfer method */
ret = claim_fiq(&hw->fiq_handler);
if (ret)
return;
}
if (hw->tx && !hw->rx)
mode = FIQ_MODE_TX;
else if (hw->rx && !hw->tx)
mode = FIQ_MODE_RX;
else
mode = FIQ_MODE_TXRX;
regs.uregs[fiq_rspi] = (long)hw->regs;
regs.uregs[fiq_rrx] = (long)hw->rx;
regs.uregs[fiq_rtx] = (long)hw->tx + 1;
regs.uregs[fiq_rcount] = hw->len - 1;
regs.uregs[fiq_rirq] = (long)S3C24XX_VA_IRQ;
set_fiq_regs(&regs);
if (hw->fiq_mode != mode) {
u32 *ack_ptr;
hw->fiq_mode = mode;
switch (mode) {
case FIQ_MODE_TX:
code = &s3c24xx_spi_fiq_tx;
break;
case FIQ_MODE_RX:
code = &s3c24xx_spi_fiq_rx;
break;
case FIQ_MODE_TXRX:
code = &s3c24xx_spi_fiq_txrx;
break;
default:
code = NULL;
}
BUG_ON(!code);
ack_ptr = (u32 *)&code->data[code->ack_offset];
*ack_ptr = ack_bit(hw->irq);
set_fiq_handler(&code->data, code->length);
}
s3c24xx_set_fiq(hw->irq, true);
hw->fiq_mode = mode;
hw->fiq_inuse = 1;
}
/**
* s3c24xx_spi_fiqop - FIQ core code callback
* @pw: Data registered with the handler
* @release: Whether this is a release or a return.
*
* Called by the FIQ code when another module wants to use the FIQ, so
* return whether we are currently using this or not and then update our
* internal state.
*/
static int s3c24xx_spi_fiqop(void *pw, int release)
{
struct s3c24xx_spi *hw = pw;
int ret = 0;
if (release) {
if (hw->fiq_inuse)
ret = -EBUSY;
/* note, we do not need to unroute the FIQ, as the FIQ
* vector code de-routes it to signal the end of transfer */
hw->fiq_mode = FIQ_MODE_NONE;
hw->fiq_claimed = 0;
} else {
hw->fiq_claimed = 1;
}
return ret;
}
/**
* s3c24xx_spi_initfiq - setup the information for the FIQ core
* @hw: The hardware state.
*
* Setup the fiq_handler block to pass to the FIQ core.
*/
static inline void s3c24xx_spi_initfiq(struct s3c24xx_spi *hw)
{
hw->fiq_handler.dev_id = hw;
hw->fiq_handler.name = dev_name(hw->dev);
hw->fiq_handler.fiq_op = s3c24xx_spi_fiqop;
}
/**
* s3c24xx_spi_usefiq - return if we should be using FIQ.
* @hw: The hardware state.
*
* Return true if the platform data specifies whether this channel is
* allowed to use the FIQ.
*/
static inline bool s3c24xx_spi_usefiq(struct s3c24xx_spi *hw)
{
return hw->pdata->use_fiq;
}
/**
* s3c24xx_spi_usingfiq - return if channel is using FIQ
* @spi: The hardware state.
*
* Return whether the channel is currently using the FIQ (separate from
* whether the FIQ is claimed).
*/
static inline bool s3c24xx_spi_usingfiq(struct s3c24xx_spi *spi)
{
return spi->fiq_inuse;
}
#else
static inline void s3c24xx_spi_initfiq(struct s3c24xx_spi *s) { }
static inline void s3c24xx_spi_tryfiq(struct s3c24xx_spi *s) { }
static inline bool s3c24xx_spi_usefiq(struct s3c24xx_spi *s) { return false; }
static inline bool s3c24xx_spi_usingfiq(struct s3c24xx_spi *s) { return false; }
#endif /* CONFIG_SPI_S3C24XX_FIQ */
static int s3c24xx_spi_txrx(struct spi_device *spi, struct spi_transfer *t)
{
struct s3c24xx_spi *hw = to_hw(spi);
dev_dbg(&spi->dev, "txrx: tx %p, rx %p, len %d\n",
t->tx_buf, t->rx_buf, t->len);
hw->tx = t->tx_buf;
hw->rx = t->rx_buf;
hw->len = t->len;
......@@ -228,11 +429,14 @@ static int s3c24xx_spi_txrx(struct spi_device *spi, struct spi_transfer *t)
init_completion(&hw->done);
hw->fiq_inuse = 0;
if (s3c24xx_spi_usefiq(hw) && t->len >= 3)
s3c24xx_spi_tryfiq(hw);
/* send the first byte */
writeb(hw_txbyte(hw, 0), hw->regs + S3C2410_SPTDAT);
wait_for_completion(&hw->done);
return hw->count;
}
......@@ -254,6 +458,7 @@ static irqreturn_t s3c24xx_spi_irq(int irq, void *dev)
goto irq_done;
}
if (!s3c24xx_spi_usingfiq(hw)) {
hw->count++;
if (hw->rx)
......@@ -265,6 +470,15 @@ static irqreturn_t s3c24xx_spi_irq(int irq, void *dev)
writeb(hw_txbyte(hw, count), hw->regs + S3C2410_SPTDAT);
else
complete(&hw->done);
} else {
hw->count = hw->len;
hw->fiq_inuse = 0;
if (hw->rx)
hw->rx[hw->len-1] = readb(hw->regs + S3C2410_SPRDAT);
complete(&hw->done);
}
irq_done:
return IRQ_HANDLED;
......@@ -322,6 +536,10 @@ static int __init s3c24xx_spi_probe(struct platform_device *pdev)
platform_set_drvdata(pdev, hw);
init_completion(&hw->done);
/* initialise fiq handler */
s3c24xx_spi_initfiq(hw);
/* setup the master state. */
/* the spi->mode bits understood by this driver: */
......
/* linux/drivers/spi/spi_s3c24xx_fiq.S
*
* Copyright 2009 Simtec Electronics
* Ben Dooks <ben@simtec.co.uk>
*
* S3C24XX SPI - FIQ pseudo-DMA transfer code
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
#include <linux/linkage.h>
#include <asm/assembler.h>
#include <mach/map.h>
#include <mach/regs-irq.h>
#include <plat/regs-spi.h>
#include "spi_s3c24xx_fiq.h"
.text
@ entry to these routines is as follows, with the register names
@ defined in fiq.h so that they can be shared with the C files which
@ setup the calling registers.
@
@ fiq_rirq The base of the IRQ registers to find S3C2410_SRCPND
@ fiq_rtmp Temporary register to hold tx/rx data
@ fiq_rspi The base of the SPI register block
@ fiq_rtx The tx buffer pointer
@ fiq_rrx The rx buffer pointer
@ fiq_rcount The number of bytes to move
@ each entry starts with a word entry of how long it is
@ and an offset to the irq acknowledgment word
ENTRY(s3c24xx_spi_fiq_rx)
s3c24xx_spi_fix_rx:
.word fiq_rx_end - fiq_rx_start
.word fiq_rx_irq_ack - fiq_rx_start
fiq_rx_start:
ldr fiq_rtmp, fiq_rx_irq_ack
str fiq_rtmp, [ fiq_rirq, # S3C2410_SRCPND - S3C24XX_VA_IRQ ]
ldrb fiq_rtmp, [ fiq_rspi, # S3C2410_SPRDAT ]
strb fiq_rtmp, [ fiq_rrx ], #1
mov fiq_rtmp, #0xff
strb fiq_rtmp, [ fiq_rspi, # S3C2410_SPTDAT ]
subs fiq_rcount, fiq_rcount, #1
subnes pc, lr, #4 @@ return, still have work to do
@@ set IRQ controller so that next op will trigger IRQ
mov fiq_rtmp, #0
str fiq_rtmp, [ fiq_rirq, # S3C2410_INTMOD - S3C24XX_VA_IRQ ]
subs pc, lr, #4
fiq_rx_irq_ack:
.word 0
fiq_rx_end:
ENTRY(s3c24xx_spi_fiq_txrx)
s3c24xx_spi_fiq_txrx:
.word fiq_txrx_end - fiq_txrx_start
.word fiq_txrx_irq_ack - fiq_txrx_start
fiq_txrx_start:
ldrb fiq_rtmp, [ fiq_rspi, # S3C2410_SPRDAT ]
strb fiq_rtmp, [ fiq_rrx ], #1
ldr fiq_rtmp, fiq_txrx_irq_ack
str fiq_rtmp, [ fiq_rirq, # S3C2410_SRCPND - S3C24XX_VA_IRQ ]
ldrb fiq_rtmp, [ fiq_rtx ], #1
strb fiq_rtmp, [ fiq_rspi, # S3C2410_SPTDAT ]
subs fiq_rcount, fiq_rcount, #1
subnes pc, lr, #4 @@ return, still have work to do
mov fiq_rtmp, #0
str fiq_rtmp, [ fiq_rirq, # S3C2410_INTMOD - S3C24XX_VA_IRQ ]
subs pc, lr, #4
fiq_txrx_irq_ack:
.word 0
fiq_txrx_end:
ENTRY(s3c24xx_spi_fiq_tx)
s3c24xx_spi_fix_tx:
.word fiq_tx_end - fiq_tx_start
.word fiq_tx_irq_ack - fiq_tx_start
fiq_tx_start:
ldrb fiq_rtmp, [ fiq_rspi, # S3C2410_SPRDAT ]
ldr fiq_rtmp, fiq_tx_irq_ack
str fiq_rtmp, [ fiq_rirq, # S3C2410_SRCPND - S3C24XX_VA_IRQ ]
ldrb fiq_rtmp, [ fiq_rtx ], #1
strb fiq_rtmp, [ fiq_rspi, # S3C2410_SPTDAT ]
subs fiq_rcount, fiq_rcount, #1
subnes pc, lr, #4 @@ return, still have work to do
mov fiq_rtmp, #0
str fiq_rtmp, [ fiq_rirq, # S3C2410_INTMOD - S3C24XX_VA_IRQ ]
subs pc, lr, #4
fiq_tx_irq_ack:
.word 0
fiq_tx_end:
.end
/* linux/drivers/spi/spi_s3c24xx_fiq.h
*
* Copyright 2009 Simtec Electronics
* Ben Dooks <ben@simtec.co.uk>
*
* S3C24XX SPI - FIQ pseudo-DMA transfer support
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
/* We have R8 through R13 to play with */
#ifdef __ASSEMBLY__
#define __REG_NR(x) r##x
#else
#define __REG_NR(x) (x)
#endif
#define fiq_rspi __REG_NR(8)
#define fiq_rtmp __REG_NR(9)
#define fiq_rrx __REG_NR(10)
#define fiq_rtx __REG_NR(11)
#define fiq_rcount __REG_NR(12)
#define fiq_rirq __REG_NR(13)
This diff is collapsed.
......@@ -148,7 +148,7 @@ static int sh_sci_spi_probe(struct platform_device *dev)
ret = -ENOENT;
goto err1;
}
sp->membase = ioremap(r->start, r->end - r->start + 1);
sp->membase = ioremap(r->start, resource_size(r));
if (!sp->membase) {
ret = -ENXIO;
goto err1;
......
......@@ -375,12 +375,10 @@ static int __init txx9spi_probe(struct platform_device *dev)
res = platform_get_resource(dev, IORESOURCE_MEM, 0);
if (!res)
goto exit_busy;
if (!devm_request_mem_region(&dev->dev,
res->start, res->end - res->start + 1,
if (!devm_request_mem_region(&dev->dev, res->start, resource_size(res),
"spi_txx9"))
goto exit_busy;
c->membase = devm_ioremap(&dev->dev,
res->start, res->end - res->start + 1);
c->membase = devm_ioremap(&dev->dev, res->start, resource_size(res));
if (!c->membase)
goto exit_busy;
......
......@@ -53,7 +53,7 @@
#define SPIDEV_MAJOR 153 /* assigned */
#define N_SPI_MINORS 32 /* ... up to 256 */
static unsigned long minors[N_SPI_MINORS / BITS_PER_LONG];
static DECLARE_BITMAP(minors, N_SPI_MINORS);
/* Bit masks for spi_device.mode management. Note that incorrect
......@@ -558,7 +558,7 @@ static struct class *spidev_class;
/*-------------------------------------------------------------------------*/
static int spidev_probe(struct spi_device *spi)
static int __devinit spidev_probe(struct spi_device *spi)
{
struct spidev_data *spidev;
int status;
......@@ -607,7 +607,7 @@ static int spidev_probe(struct spi_device *spi)
return status;
}
static int spidev_remove(struct spi_device *spi)
static int __devexit spidev_remove(struct spi_device *spi)
{
struct spidev_data *spidev = spi_get_drvdata(spi);
......@@ -629,7 +629,7 @@ static int spidev_remove(struct spi_device *spi)
return 0;
}
static struct spi_driver spidev_spi = {
static struct spi_driver spidev_spi_driver = {
.driver = {
.name = "spidev",
.owner = THIS_MODULE,
......@@ -661,14 +661,14 @@ static int __init spidev_init(void)
spidev_class = class_create(THIS_MODULE, "spidev");
if (IS_ERR(spidev_class)) {
unregister_chrdev(SPIDEV_MAJOR, spidev_spi.driver.name);
unregister_chrdev(SPIDEV_MAJOR, spidev_spi_driver.driver.name);
return PTR_ERR(spidev_class);
}
status = spi_register_driver(&spidev_spi);
status = spi_register_driver(&spidev_spi_driver);
if (status < 0) {
class_destroy(spidev_class);
unregister_chrdev(SPIDEV_MAJOR, spidev_spi.driver.name);
unregister_chrdev(SPIDEV_MAJOR, spidev_spi_driver.driver.name);
}
return status;
}
......@@ -676,9 +676,9 @@ module_init(spidev_init);
static void __exit spidev_exit(void)
{
spi_unregister_driver(&spidev_spi);
spi_unregister_driver(&spidev_spi_driver);
class_destroy(spidev_class);
unregister_chrdev(SPIDEV_MAJOR, spidev_spi.driver.name);
unregister_chrdev(SPIDEV_MAJOR, spidev_spi_driver.driver.name);
}
module_exit(spidev_exit);
......
#ifndef DW_SPI_HEADER_H
#define DW_SPI_HEADER_H
#include <linux/io.h>
/* Bit fields in CTRLR0 */
#define SPI_DFS_OFFSET 0
#define SPI_FRF_OFFSET 4
#define SPI_FRF_SPI 0x0
#define SPI_FRF_SSP 0x1
#define SPI_FRF_MICROWIRE 0x2
#define SPI_FRF_RESV 0x3
#define SPI_MODE_OFFSET 6
#define SPI_SCPH_OFFSET 6
#define SPI_SCOL_OFFSET 7
#define SPI_TMOD_OFFSET 8
#define SPI_TMOD_TR 0x0 /* xmit & recv */
#define SPI_TMOD_TO 0x1 /* xmit only */
#define SPI_TMOD_RO 0x2 /* recv only */
#define SPI_TMOD_EPROMREAD 0x3 /* eeprom read mode */
#define SPI_SLVOE_OFFSET 10
#define SPI_SRL_OFFSET 11
#define SPI_CFS_OFFSET 12
/* Bit fields in SR, 7 bits */
#define SR_MASK 0x7f /* cover 7 bits */
#define SR_BUSY (1 << 0)
#define SR_TF_NOT_FULL (1 << 1)
#define SR_TF_EMPT (1 << 2)
#define SR_RF_NOT_EMPT (1 << 3)
#define SR_RF_FULL (1 << 4)
#define SR_TX_ERR (1 << 5)
#define SR_DCOL (1 << 6)
/* Bit fields in ISR, IMR, RISR, 7 bits */
#define SPI_INT_TXEI (1 << 0)
#define SPI_INT_TXOI (1 << 1)
#define SPI_INT_RXUI (1 << 2)
#define SPI_INT_RXOI (1 << 3)
#define SPI_INT_RXFI (1 << 4)
#define SPI_INT_MSTI (1 << 5)
/* TX RX interrupt level threshhold, max can be 256 */
#define SPI_INT_THRESHOLD 32
enum dw_ssi_type {
SSI_MOTO_SPI = 0,
SSI_TI_SSP,
SSI_NS_MICROWIRE,
};
struct dw_spi_reg {
u32 ctrl0;
u32 ctrl1;
u32 ssienr;
u32 mwcr;
u32 ser;
u32 baudr;
u32 txfltr;
u32 rxfltr;
u32 txflr;
u32 rxflr;
u32 sr;
u32 imr;
u32 isr;
u32 risr;
u32 txoicr;
u32 rxoicr;
u32 rxuicr;
u32 msticr;
u32 icr;
u32 dmacr;
u32 dmatdlr;
u32 dmardlr;
u32 idr;
u32 version;
u32 dr; /* Currently oper as 32 bits,
though only low 16 bits matters */
} __packed;
struct dw_spi {
struct spi_master *master;
struct spi_device *cur_dev;
struct device *parent_dev;
enum dw_ssi_type type;
void __iomem *regs;
unsigned long paddr;
u32 iolen;
int irq;
u32 max_freq; /* max bus freq supported */
u16 bus_num;
u16 num_cs; /* supported slave numbers */
/* Driver message queue */
struct workqueue_struct *workqueue;
struct work_struct pump_messages;
spinlock_t lock;
struct list_head queue;
int busy;
int run;
/* Message Transfer pump */
struct tasklet_struct pump_transfers;
/* Current message transfer state info */
struct spi_message *cur_msg;
struct spi_transfer *cur_transfer;
struct chip_data *cur_chip;
struct chip_data *prev_chip;
size_t len;
void *tx;
void *tx_end;
void *rx;
void *rx_end;
int dma_mapped;
dma_addr_t rx_dma;
dma_addr_t tx_dma;
size_t rx_map_len;
size_t tx_map_len;
u8 n_bytes; /* current is a 1/2 bytes op */
u8 max_bits_per_word; /* maxim is 16b */
u32 dma_width;
int cs_change;
int (*write)(struct dw_spi *dws);
int (*read)(struct dw_spi *dws);
irqreturn_t (*transfer_handler)(struct dw_spi *dws);
void (*cs_control)(u32 command);
/* Dma info */
int dma_inited;
struct dma_chan *txchan;
struct dma_chan *rxchan;
int txdma_done;
int rxdma_done;
u64 tx_param;
u64 rx_param;
struct device *dma_dev;
dma_addr_t dma_addr;
/* Bus interface info */
void *priv;
#ifdef CONFIG_DEBUG_FS
struct dentry *debugfs;
#endif
};
#define dw_readl(dw, name) \
__raw_readl(&(((struct dw_spi_reg *)dw->regs)->name))
#define dw_writel(dw, name, val) \
__raw_writel((val), &(((struct dw_spi_reg *)dw->regs)->name))
#define dw_readw(dw, name) \
__raw_readw(&(((struct dw_spi_reg *)dw->regs)->name))
#define dw_writew(dw, name, val) \
__raw_writew((val), &(((struct dw_spi_reg *)dw->regs)->name))
static inline void spi_enable_chip(struct dw_spi *dws, int enable)
{
dw_writel(dws, ssienr, (enable ? 1 : 0));
}
static inline void spi_set_clk(struct dw_spi *dws, u16 div)
{
dw_writel(dws, baudr, div);
}
static inline void spi_chip_sel(struct dw_spi *dws, u16 cs)
{
if (cs > dws->num_cs)
return;
dw_writel(dws, ser, 1 << cs);
}
/* Disable IRQ bits */
static inline void spi_mask_intr(struct dw_spi *dws, u32 mask)
{
u32 new_mask;
new_mask = dw_readl(dws, imr) & ~mask;
dw_writel(dws, imr, new_mask);
}
/* Enable IRQ bits */
static inline void spi_umask_intr(struct dw_spi *dws, u32 mask)
{
u32 new_mask;
new_mask = dw_readl(dws, imr) | mask;
dw_writel(dws, imr, new_mask);
}
/*
* Each SPI slave device to work with dw_api controller should
* has such a structure claiming its working mode (PIO/DMA etc),
* which can be save in the "controller_data" member of the
* struct spi_device
*/
struct dw_spi_chip {
u8 poll_mode; /* 0 for contoller polling mode */
u8 type; /* SPI/SSP/Micrwire */
u8 enable_dma;
void (*cs_control)(u32 command);
};
extern int dw_spi_add_host(struct dw_spi *dws);
extern void dw_spi_remove_host(struct dw_spi *dws);
extern int dw_spi_suspend_host(struct dw_spi *dws);
extern int dw_spi_resume_host(struct dw_spi *dws);
#endif /* DW_SPI_HEADER_H */
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment