net: hns: bug fix about getting hilink status for HNS v2

The hilink status reg in HNS V2 is different from HNS v1. In HNS V2, It
distinguishes differnt lane status according to the bit-field of the reg.
As is shown below:
[0:0] ---> lane0
[1:1] ---> lane1
...

But the current driver reads the reg to get the hilink status ONLY
concidering HNS V1 situation. Here is a patch to support both of them.
Signed-off-by: Sheng Li <lisheng011@huawei.com>
Signed-off-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/ethernet/hisilicon/hns/hns_dsaf_misc.c

@@ -244,31 +244,35 @@ void hns_ppe_com_srst(struct ppe_common_cb *ppe_common, u32 val)
  */
 phy_interface_t hns_mac_get_phy_if(struct hns_mac_cb *mac_cb)
 {
-	u32 hilink3_mode;
-	u32 hilink4_mode;
+	u32 mode;
+	u32 reg;
+	u32 shift;
+	bool is_ver1 = AE_IS_VER1(mac_cb->dsaf_dev->dsaf_ver);
 	void __iomem *sys_ctl_vaddr = mac_cb->sys_ctl_vaddr;
-	int dev_id = mac_cb->mac_id;
+	int mac_id = mac_cb->mac_id;
 	phy_interface_t phy_if = PHY_INTERFACE_MODE_NA;
 
-	hilink3_mode = dsaf_read_reg(sys_ctl_vaddr, HNS_MAC_HILINK3_REG);
-	hilink4_mode = dsaf_read_reg(sys_ctl_vaddr, HNS_MAC_HILINK4_REG);
-	if (dev_id >= 0 && dev_id <= 3) {
-		if (hilink4_mode == 0)
+	if (is_ver1 && (mac_id >= 6 && mac_id <= 7)) {
 		phy_if = PHY_INTERFACE_MODE_SGMII;
-		else
+	} else if (mac_id >= 0 && mac_id <= 3) {
+		reg = is_ver1 ? HNS_MAC_HILINK4_REG : HNS_MAC_HILINK4V2_REG;
+		mode = dsaf_read_reg(sys_ctl_vaddr, reg);
+		/* mac_id 0, 1, 2, 3 ---> hilink4 lane 0, 1, 2, 3 */
+		shift = is_ver1 ? 0 : mac_id;
+		if (dsaf_get_bit(mode, shift))
 			phy_if = PHY_INTERFACE_MODE_XGMII;
-	} else if (dev_id >= 4 && dev_id <= 5) {
-		if (hilink3_mode == 0)
-			phy_if = PHY_INTERFACE_MODE_SGMII;
 		else
+			phy_if = PHY_INTERFACE_MODE_SGMII;
+	} else if (mac_id >= 4 && mac_id <= 7) {
+		reg = is_ver1 ? HNS_MAC_HILINK3_REG : HNS_MAC_HILINK3V2_REG;
+		mode = dsaf_read_reg(sys_ctl_vaddr, reg);
+		/* mac_id 4, 5, 6, 7 ---> hilink3 lane 2, 3, 0, 1 */
+		shift = is_ver1 ? 0 : mac_id <= 5 ? mac_id - 2 : mac_id - 6;
+		if (dsaf_get_bit(mode, shift))
 			phy_if = PHY_INTERFACE_MODE_XGMII;
-	} else {
+		else
 			phy_if = PHY_INTERFACE_MODE_SGMII;
 	}
-
-	dev_dbg(mac_cb->dev,
-		"hilink3_mode=%d, hilink4_mode=%d dev_id=%d, phy_if=%d\n",
-		hilink3_mode, hilink4_mode, dev_id, phy_if);
 	return phy_if;
 }
 

drivers/net/ethernet/hisilicon/hns/hns_dsaf_reg.h

@@ -103,6 +103,8 @@
 /*serdes offset**/
 #define HNS_MAC_HILINK3_REG DSAF_SUB_SC_HILINK3_CRG_CTRL0_REG
 #define HNS_MAC_HILINK4_REG DSAF_SUB_SC_HILINK4_CRG_CTRL0_REG
+#define HNS_MAC_HILINK3V2_REG DSAF_SUB_SC_HILINK3_CRG_CTRL1_REG
+#define HNS_MAC_HILINK4V2_REG DSAF_SUB_SC_HILINK4_CRG_CTRL1_REG
 #define HNS_MAC_LANE0_CTLEDFE_REG 0x000BFFCCULL
 #define HNS_MAC_LANE1_CTLEDFE_REG 0x000BFFBCULL
 #define HNS_MAC_LANE2_CTLEDFE_REG 0x000BFFACULL