Skip to content

L
linux
Commit c3033b01 authored by Joe Perches's avatar Joe Perches Committed by Jeff Garzik
Browse files
Options

e1000: Convert boolean_t to bool 

On Thu, 2008-03-06 at 10:07 -0800, Kok, Auke wrote:
> send me a patch for e1000 and for ixgb and I'll happily apply those :)

boolean_t to bool
TRUE to true
FALSE to false
comment typo ahread to ahead
Signed-off-by: default avatarJoe Perches <joe@perches.com>
Signed-off-by: default avatarAuke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: default avatarJeff Garzik <jeff@garzik.org>
parent f89e6e38
Show whitespace changes
Inline Side-by-side
Showing with 209 additions and 216 deletions
drivers/net/e1000/e1000.h
View file @ c3033b01
......@@ -188,7 +188,7 @@ struct e1000_tx_ring {
spinlock_t tx_lock;
uint16_t tdh;
uint16_t tdt;
boolean_t last_tx_tso;
bool last_tx_tso;
};
struct e1000_rx_ring {
......@@ -283,16 +283,16 @@ struct e1000_adapter {
uint32_t tx_fifo_size;
uint8_t tx_timeout_factor;
atomic_t tx_fifo_stall;
boolean_t pcix_82544;
boolean_t detect_tx_hung;
bool pcix_82544;
bool detect_tx_hung;
/* RX */
#ifdef CONFIG_E1000_NAPI
boolean_t (*clean_rx) (struct e1000_adapter *adapter,
bool (*clean_rx) (struct e1000_adapter *adapter,
struct e1000_rx_ring *rx_ring,
int *work_done, int work_to_do);
#else
boolean_t (*clean_rx) (struct e1000_adapter *adapter,
bool (*clean_rx) (struct e1000_adapter *adapter,
struct e1000_rx_ring *rx_ring);
#endif
void (*alloc_rx_buf) (struct e1000_adapter *adapter,
......@@ -312,7 +312,7 @@ struct e1000_adapter {
uint32_t alloc_rx_buff_failed;
uint32_t rx_int_delay;
uint32_t rx_abs_int_delay;
boolean_t rx_csum;
bool rx_csum;
unsigned int rx_ps_pages;
uint32_t gorcl;
uint64_t gorcl_old;
......@@ -335,12 +335,12 @@ struct e1000_adapter {
struct e1000_rx_ring test_rx_ring;
int msg_enable;
boolean_t have_msi;
bool have_msi;
/* to not mess up cache alignment, always add to the bottom */
boolean_t tso_force;
boolean_t smart_power_down; /* phy smart power down */
boolean_t quad_port_a;
bool tso_force;
bool smart_power_down; /* phy smart power down */
bool quad_port_a;
unsigned long flags;
uint32_t eeprom_wol;
};
......
drivers/net/e1000/e1000_ethtool.c
View file @ c3033b01
......@@ -353,7 +353,7 @@ e1000_set_tso(struct net_device *netdev, uint32_t data)
netdev->features &= ~NETIF_F_TSO6;
DPRINTK(PROBE, INFO, "TSO is %s\n", data ? "Enabled" : "Disabled");
adapter->tso_force = TRUE;
adapter->tso_force = true;
return 0;
}
......@@ -922,7 +922,8 @@ static int
e1000_intr_test(struct e1000_adapter *adapter, uint64_t *data)
{
struct net_device *netdev = adapter->netdev;
uint32_t mask, i=0, shared_int = TRUE;
uint32_t mask, i = 0;
bool shared_int = true;
uint32_t irq = adapter->pdev->irq;
*data = 0;
......@@ -931,7 +932,7 @@ e1000_intr_test(struct e1000_adapter *adapter, uint64_t *data)
/* Hook up test interrupt handler just for this test */
if (!request_irq(irq, &e1000_test_intr, IRQF_PROBE_SHARED, netdev->name,
netdev))
shared_int = FALSE;
shared_int = false;
else if (request_irq(irq, &e1000_test_intr, IRQF_SHARED,
netdev->name, netdev)) {
*data = 1;
......@@ -1295,7 +1296,7 @@ e1000_integrated_phy_loopback(struct e1000_adapter *adapter)
uint32_t ctrl_reg = 0;
uint32_t stat_reg = 0;
adapter->hw.autoneg = FALSE;
adapter->hw.autoneg = false;
if (adapter->hw.phy_type == e1000_phy_m88) {
/* Auto-MDI/MDIX Off */
......@@ -1473,7 +1474,7 @@ e1000_loopback_cleanup(struct e1000_adapter *adapter)
case e1000_82545_rev_3:
case e1000_82546_rev_3:
default:
hw->autoneg = TRUE;
hw->autoneg = true;
if (hw->phy_type == e1000_phy_gg82563)
e1000_write_phy_reg(hw,
GG82563_PHY_KMRN_MODE_CTRL,
......@@ -1607,13 +1608,13 @@ e1000_link_test(struct e1000_adapter *adapter, uint64_t *data)
*data = 0;
if (adapter->hw.media_type == e1000_media_type_internal_serdes) {
int i = 0;
adapter->hw.serdes_link_down = TRUE;
adapter->hw.serdes_link_down = true;
/* On some blade server designs, link establishment
* could take as long as 2-3 minutes */
do {
e1000_check_for_link(&adapter->hw);
if (adapter->hw.serdes_link_down == FALSE)
if (!adapter->hw.serdes_link_down)
return *data;
msleep(20);
} while (i++ < 3750);
......@@ -1649,7 +1650,7 @@ e1000_diag_test(struct net_device *netdev,
struct ethtool_test *eth_test, uint64_t *data)
{
struct e1000_adapter *adapter = netdev_priv(netdev);
boolean_t if_running = netif_running(netdev);
bool if_running = netif_running(netdev);
set_bit(__E1000_TESTING, &adapter->flags);
if (eth_test->flags == ETH_TEST_FL_OFFLINE) {
......
drivers/net/e1000/e1000_hw.c
View file @ c3033b01
......@@ -46,7 +46,8 @@ static int32_t e1000_check_polarity(struct e1000_hw *hw, e1000_rev_polarity *pol
static void e1000_clear_hw_cntrs(struct e1000_hw *hw);
static void e1000_clear_vfta(struct e1000_hw *hw);
static int32_t e1000_commit_shadow_ram(struct e1000_hw *hw);
static int32_t e1000_config_dsp_after_link_change(struct e1000_hw *hw, boolean_t link_up);
static int32_t e1000_config_dsp_after_link_change(struct e1000_hw *hw,
bool link_up);
static int32_t e1000_config_fc_after_link_up(struct e1000_hw *hw);
static int32_t e1000_detect_gig_phy(struct e1000_hw *hw);
static int32_t e1000_erase_ich8_4k_segment(struct e1000_hw *hw, uint32_t bank);
......@@ -62,7 +63,7 @@ static int32_t e1000_init_lcd_from_nvm_config_region(struct e1000_hw *hw, uint32
static int32_t e1000_init_lcd_from_nvm(struct e1000_hw *hw);
static void e1000_init_rx_addrs(struct e1000_hw *hw);
static void e1000_initialize_hardware_bits(struct e1000_hw *hw);
static boolean_t e1000_is_onboard_nvm_eeprom(struct e1000_hw *hw);
static bool e1000_is_onboard_nvm_eeprom(struct e1000_hw *hw);
static int32_t e1000_kumeran_lock_loss_workaround(struct e1000_hw *hw);
static int32_t e1000_mng_enable_host_if(struct e1000_hw *hw);
static int32_t e1000_mng_host_if_write(struct e1000_hw *hw, uint8_t *buffer, uint16_t length, uint16_t offset, uint8_t *sum);
......@@ -84,8 +85,8 @@ static int32_t e1000_write_ich8_data(struct e1000_hw *hw, uint32_t index, uint32
static int32_t e1000_read_eeprom_ich8(struct e1000_hw *hw, uint16_t offset, uint16_t words, uint16_t *data);
static int32_t e1000_write_eeprom_ich8(struct e1000_hw *hw, uint16_t offset, uint16_t words, uint16_t *data);
static void e1000_release_software_flag(struct e1000_hw *hw);
static int32_t e1000_set_d3_lplu_state(struct e1000_hw *hw, boolean_t active);
static int32_t e1000_set_d0_lplu_state(struct e1000_hw *hw, boolean_t active);
static int32_t e1000_set_d3_lplu_state(struct e1000_hw *hw, bool active);
static int32_t e1000_set_d0_lplu_state(struct e1000_hw *hw, bool active);
static int32_t e1000_set_pci_ex_no_snoop(struct e1000_hw *hw, uint32_t no_snoop);
static void e1000_set_pci_express_master_disable(struct e1000_hw *hw);
static int32_t e1000_wait_autoneg(struct e1000_hw *hw);
......@@ -425,22 +426,22 @@ e1000_set_mac_type(struct e1000_hw *hw)
switch (hw->mac_type) {
case e1000_ich8lan:
hw->swfwhw_semaphore_present = TRUE;
hw->asf_firmware_present = TRUE;
hw->swfwhw_semaphore_present = true;
hw->asf_firmware_present = true;
break;
case e1000_80003es2lan:
hw->swfw_sync_present = TRUE;
hw->swfw_sync_present = true;
/* fall through */
case e1000_82571:
case e1000_82572:
case e1000_82573:
hw->eeprom_semaphore_present = TRUE;
hw->eeprom_semaphore_present = true;
/* fall through */
case e1000_82541:
case e1000_82547:
case e1000_82541_rev_2:
case e1000_82547_rev_2:
hw->asf_firmware_present = TRUE;
hw->asf_firmware_present = true;
break;
default:
break;
......@@ -450,20 +451,20 @@ e1000_set_mac_type(struct e1000_hw *hw)
* FD mode
*/
if (hw->mac_type == e1000_82543)
hw->bad_tx_carr_stats_fd = TRUE;
hw->bad_tx_carr_stats_fd = true;
/* capable of receiving management packets to the host */
if (hw->mac_type >= e1000_82571)
hw->has_manc2h = TRUE;
hw->has_manc2h = true;
/* In rare occasions, ESB2 systems would end up started without
* the RX unit being turned on.
*/
if (hw->mac_type == e1000_80003es2lan)
hw->rx_needs_kicking = TRUE;
hw->rx_needs_kicking = true;
if (hw->mac_type > e1000_82544)
hw->has_smbus = TRUE;
hw->has_smbus = true;
return E1000_SUCCESS;
}
......@@ -482,7 +483,7 @@ e1000_set_media_type(struct e1000_hw *hw)
if (hw->mac_type != e1000_82543) {
/* tbi_compatibility is only valid on 82543 */
hw->tbi_compatibility_en = FALSE;
hw->tbi_compatibility_en = false;
}
switch (hw->device_id) {
......@@ -513,7 +514,7 @@ e1000_set_media_type(struct e1000_hw *hw)
if (status & E1000_STATUS_TBIMODE) {
hw->media_type = e1000_media_type_fiber;
/* tbi_compatibility not valid on fiber */
hw->tbi_compatibility_en = FALSE;
hw->tbi_compatibility_en = false;
} else {
hw->media_type = e1000_media_type_copper;
}
......@@ -569,7 +570,7 @@ e1000_reset_hw(struct e1000_hw *hw)
E1000_WRITE_FLUSH(hw);
/* The tbi_compatibility_on Flag must be cleared when Rctl is cleared. */
hw->tbi_compatibility_on = FALSE;
hw->tbi_compatibility_on = false;
/* Delay to allow any outstanding PCI transactions to complete before
* resetting the device
......@@ -682,7 +683,7 @@ e1000_reset_hw(struct e1000_hw *hw)
msleep(20);
break;
case e1000_82573:
if (e1000_is_onboard_nvm_eeprom(hw) == FALSE) {
if (!e1000_is_onboard_nvm_eeprom(hw)) {
udelay(10);
ctrl_ext = E1000_READ_REG(hw, CTRL_EXT);
ctrl_ext |= E1000_CTRL_EXT_EE_RST;
......@@ -1428,7 +1429,7 @@ e1000_copper_link_preconfig(struct e1000_hw *hw)
if (hw->mac_type <= e1000_82543 ||
hw->mac_type == e1000_82541 || hw->mac_type == e1000_82547 ||
hw->mac_type == e1000_82541_rev_2 || hw->mac_type == e1000_82547_rev_2)
hw->phy_reset_disable = FALSE;
hw->phy_reset_disable = false;
return E1000_SUCCESS;
}
......@@ -1470,7 +1471,7 @@ e1000_copper_link_igp_setup(struct e1000_hw *hw)
/* The NVM settings will configure LPLU in D3 for IGP2 and IGP3 PHYs */
if (hw->phy_type == e1000_phy_igp) {
/* disable lplu d3 during driver init */
ret_val = e1000_set_d3_lplu_state(hw, FALSE);
ret_val = e1000_set_d3_lplu_state(hw, false);
if (ret_val) {
DEBUGOUT("Error Disabling LPLU D3\n");
return ret_val;
......@@ -1478,7 +1479,7 @@ e1000_copper_link_igp_setup(struct e1000_hw *hw)
}
/* disable lplu d0 during driver init */
ret_val = e1000_set_d0_lplu_state(hw, FALSE);
ret_val = e1000_set_d0_lplu_state(hw, false);
if (ret_val) {
DEBUGOUT("Error Disabling LPLU D0\n");
return ret_val;
......@@ -1691,7 +1692,7 @@ e1000_copper_link_ggp_setup(struct e1000_hw *hw)
* firmware will have already initialized them. We only initialize
* them if the HW is not in IAMT mode.
*/
if (e1000_check_mng_mode(hw) == FALSE) {
if (!e1000_check_mng_mode(hw)) {
/* Enable Electrical Idle on the PHY */
phy_data |= GG82563_PMCR_ENABLE_ELECTRICAL_IDLE;
ret_val = e1000_write_phy_reg(hw, GG82563_PHY_PWR_MGMT_CTRL,
......@@ -1892,7 +1893,7 @@ e1000_copper_link_autoneg(struct e1000_hw *hw)
}
}
hw->get_link_status = TRUE;
hw->get_link_status = true;
return E1000_SUCCESS;
}
......@@ -1932,7 +1933,7 @@ e1000_copper_link_postconfig(struct e1000_hw *hw)
/* Config DSP to improve Giga link quality */
if (hw->phy_type == e1000_phy_igp) {
ret_val = e1000_config_dsp_after_link_change(hw, TRUE);
ret_val = e1000_config_dsp_after_link_change(hw, true);
if (ret_val) {
DEBUGOUT("Error Configuring DSP after link up\n");
return ret_val;
......@@ -2923,7 +2924,7 @@ e1000_check_for_link(struct e1000_hw *hw)
if (hw->media_type == e1000_media_type_fiber) {
signal = (hw->mac_type > e1000_82544) ? E1000_CTRL_SWDPIN1 : 0;
if (status & E1000_STATUS_LU)
hw->get_link_status = FALSE;
hw->get_link_status = false;
}
}
......@@ -2947,7 +2948,7 @@ e1000_check_for_link(struct e1000_hw *hw)
return ret_val;
if (phy_data & MII_SR_LINK_STATUS) {
hw->get_link_status = FALSE;
hw->get_link_status = false;
/* Check if there was DownShift, must be checked immediately after
* link-up */
e1000_check_downshift(hw);
......@@ -2973,7 +2974,7 @@ e1000_check_for_link(struct e1000_hw *hw)
} else {
/* No link detected */
e1000_config_dsp_after_link_change(hw, FALSE);
e1000_config_dsp_after_link_change(hw, false);
return 0;
}
......@@ -2983,7 +2984,7 @@ e1000_check_for_link(struct e1000_hw *hw)
if (!hw->autoneg) return -E1000_ERR_CONFIG;
/* optimize the dsp settings for the igp phy */
e1000_config_dsp_after_link_change(hw, TRUE);
e1000_config_dsp_after_link_change(hw, true);
/* We have a M88E1000 PHY and Auto-Neg is enabled. If we
* have Si on board that is 82544 or newer, Auto
......@@ -3036,7 +3037,7 @@ e1000_check_for_link(struct e1000_hw *hw)
rctl = E1000_READ_REG(hw, RCTL);
rctl &= ~E1000_RCTL_SBP;
E1000_WRITE_REG(hw, RCTL, rctl);
hw->tbi_compatibility_on = FALSE;
hw->tbi_compatibility_on = false;
}
} else {
/* If TBI compatibility is was previously off, turn it on. For
......@@ -3045,7 +3046,7 @@ e1000_check_for_link(struct e1000_hw *hw)
* will look like CRC errors to to the hardware.
*/
if (!hw->tbi_compatibility_on) {
hw->tbi_compatibility_on = TRUE;
hw->tbi_compatibility_on = true;
rctl = E1000_READ_REG(hw, RCTL);
rctl |= E1000_RCTL_SBP;
E1000_WRITE_REG(hw, RCTL, rctl);
......@@ -3098,7 +3099,7 @@ e1000_check_for_link(struct e1000_hw *hw)
E1000_WRITE_REG(hw, TXCW, hw->txcw);
E1000_WRITE_REG(hw, CTRL, (ctrl & ~E1000_CTRL_SLU));
hw->serdes_link_down = FALSE;
hw->serdes_link_down = false;
}
/* If we force link for non-auto-negotiation switch, check link status
* based on MAC synchronization for internal serdes media type.
......@@ -3109,11 +3110,11 @@ e1000_check_for_link(struct e1000_hw *hw)
udelay(10);
if (E1000_RXCW_SYNCH & E1000_READ_REG(hw, RXCW)) {
if (!(rxcw & E1000_RXCW_IV)) {
hw->serdes_link_down = FALSE;
hw->serdes_link_down = false;
DEBUGOUT("SERDES: Link is up.\n");
}
} else {
hw->serdes_link_down = TRUE;
hw->serdes_link_down = true;
DEBUGOUT("SERDES: Link is down.\n");
}
}
......@@ -4044,7 +4045,7 @@ e1000_detect_gig_phy(struct e1000_hw *hw)
{
int32_t phy_init_status, ret_val;
uint16_t phy_id_high, phy_id_low;
boolean_t match = FALSE;
bool match = false;
DEBUGFUNC("e1000_detect_gig_phy");
......@@ -4086,35 +4087,35 @@ e1000_detect_gig_phy(struct e1000_hw *hw)
switch (hw->mac_type) {
case e1000_82543:
if (hw->phy_id == M88E1000_E_PHY_ID) match = TRUE;
if (hw->phy_id == M88E1000_E_PHY_ID) match = true;
break;
case e1000_82544:
if (hw->phy_id == M88E1000_I_PHY_ID) match = TRUE;
if (hw->phy_id == M88E1000_I_PHY_ID) match = true;
break;
case e1000_82540:
case e1000_82545:
case e1000_82545_rev_3:
case e1000_82546:
case e1000_82546_rev_3:
if (hw->phy_id == M88E1011_I_PHY_ID) match = TRUE;
if (hw->phy_id == M88E1011_I_PHY_ID) match = true;
break;
case e1000_82541:
case e1000_82541_rev_2:
case e1000_82547:
case e1000_82547_rev_2:
if (hw->phy_id == IGP01E1000_I_PHY_ID) match = TRUE;
if (hw->phy_id == IGP01E1000_I_PHY_ID) match = true;
break;
case e1000_82573:
if (hw->phy_id == M88E1111_I_PHY_ID) match = TRUE;
if (hw->phy_id == M88E1111_I_PHY_ID) match = true;
break;
case e1000_80003es2lan:
if (hw->phy_id == GG82563_E_PHY_ID) match = TRUE;
if (hw->phy_id == GG82563_E_PHY_ID) match = true;
break;
case e1000_ich8lan:
if (hw->phy_id == IGP03E1000_E_PHY_ID) match = TRUE;
if (hw->phy_id == IFE_E_PHY_ID) match = TRUE;
if (hw->phy_id == IFE_PLUS_E_PHY_ID) match = TRUE;
if (hw->phy_id == IFE_C_E_PHY_ID) match = TRUE;
if (hw->phy_id == IGP03E1000_E_PHY_ID) match = true;
if (hw->phy_id == IFE_E_PHY_ID) match = true;
if (hw->phy_id == IFE_PLUS_E_PHY_ID) match = true;
if (hw->phy_id == IFE_C_E_PHY_ID) match = true;
break;
default:
DEBUGOUT1("Invalid MAC type %d\n", hw->mac_type);
......@@ -4455,8 +4456,8 @@ e1000_init_eeprom_params(struct e1000_hw *hw)
eeprom->opcode_bits = 3;
eeprom->address_bits = 6;
eeprom->delay_usec = 50;
eeprom->use_eerd = FALSE;
eeprom->use_eewr = FALSE;
eeprom->use_eerd = false;
eeprom->use_eewr = false;
break;
case e1000_82540:
case e1000_82545:
......@@ -4473,8 +4474,8 @@ e1000_init_eeprom_params(struct e1000_hw *hw)
eeprom->word_size = 64;
eeprom->address_bits = 6;
}
eeprom->use_eerd = FALSE;
eeprom->use_eewr = FALSE;
eeprom->use_eerd = false;
eeprom->use_eewr = false;
break;
case e1000_82541:
case e1000_82541_rev_2:
......@@ -4503,8 +4504,8 @@ e1000_init_eeprom_params(struct e1000_hw *hw)
eeprom->address_bits = 6;
}
}
eeprom->use_eerd = FALSE;
eeprom->use_eewr = FALSE;
eeprom->use_eerd = false;
eeprom->use_eewr = false;
break;
case e1000_82571:
case e1000_82572:
......@@ -4518,8 +4519,8 @@ e1000_init_eeprom_params(struct e1000_hw *hw)
eeprom->page_size = 8;
eeprom->address_bits = 8;
}
eeprom->use_eerd = FALSE;
eeprom->use_eewr = FALSE;
eeprom->use_eerd = false;
eeprom->use_eewr = false;
break;
case e1000_82573:
eeprom->type = e1000_eeprom_spi;
......@@ -4532,9 +4533,9 @@ e1000_init_eeprom_params(struct e1000_hw *hw)
eeprom->page_size = 8;
eeprom->address_bits = 8;
}
eeprom->use_eerd = TRUE;
eeprom->use_eewr = TRUE;
if (e1000_is_onboard_nvm_eeprom(hw) == FALSE) {
eeprom->use_eerd = true;
eeprom->use_eewr = true;
if (!e1000_is_onboard_nvm_eeprom(hw)) {
eeprom->type = e1000_eeprom_flash;
eeprom->word_size = 2048;
......@@ -4555,8 +4556,8 @@ e1000_init_eeprom_params(struct e1000_hw *hw)
eeprom->page_size = 8;
eeprom->address_bits = 8;
}
eeprom->use_eerd = TRUE;
eeprom->use_eewr = FALSE;
eeprom->use_eerd = true;
eeprom->use_eewr = false;
break;
case e1000_ich8lan:
{
......@@ -4564,15 +4565,15 @@ e1000_init_eeprom_params(struct e1000_hw *hw)
uint32_t flash_size = E1000_READ_ICH_FLASH_REG(hw, ICH_FLASH_GFPREG);
eeprom->type = e1000_eeprom_ich8;
eeprom->use_eerd = FALSE;
eeprom->use_eewr = FALSE;
eeprom->use_eerd = false;
eeprom->use_eewr = false;
eeprom->word_size = E1000_SHADOW_RAM_WORDS;
/* Zero the shadow RAM structure. But don't load it from NVM
* so as to save time for driver init */
if (hw->eeprom_shadow_ram != NULL) {
for (i = 0; i < E1000_SHADOW_RAM_WORDS; i++) {
hw->eeprom_shadow_ram[i].modified = FALSE;
hw->eeprom_shadow_ram[i].modified = false;
hw->eeprom_shadow_ram[i].eeprom_word = 0xFFFF;
}
}
......@@ -4994,15 +4995,14 @@ e1000_read_eeprom(struct e1000_hw *hw,
* directly. In this case, we need to acquire the EEPROM so that
* FW or other port software does not interrupt.
*/
if (e1000_is_onboard_nvm_eeprom(hw) == TRUE &&
hw->eeprom.use_eerd == FALSE) {
if (e1000_is_onboard_nvm_eeprom(hw) && !hw->eeprom.use_eerd) {
/* Prepare the EEPROM for bit-bang reading */
if (e1000_acquire_eeprom(hw) != E1000_SUCCESS)
return -E1000_ERR_EEPROM;
}
/* Eerd register EEPROM access requires no eeprom aquire/release */
if (eeprom->use_eerd == TRUE)
if (eeprom->use_eerd)
return e1000_read_eeprom_eerd(hw, offset, words, data);
/* ICH EEPROM access is done via the ICH flash controller */
......@@ -5171,7 +5171,7 @@ e1000_poll_eerd_eewr_done(struct e1000_hw *hw, int eerd)
*
* hw - Struct containing variables accessed by shared code
****************************************************************************/
static boolean_t
static bool
e1000_is_onboard_nvm_eeprom(struct e1000_hw *hw)
{
uint32_t eecd = 0;
......@@ -5179,7 +5179,7 @@ e1000_is_onboard_nvm_eeprom(struct e1000_hw *hw)
DEBUGFUNC("e1000_is_onboard_nvm_eeprom");
if (hw->mac_type == e1000_ich8lan)
return FALSE;
return false;
if (hw->mac_type == e1000_82573) {
eecd = E1000_READ_REG(hw, EECD);
......@@ -5189,10 +5189,10 @@ e1000_is_onboard_nvm_eeprom(struct e1000_hw *hw)
/* If both bits are set, device is Flash type */
if (eecd == 0x03) {
return FALSE;
return false;
}
}
return TRUE;
return true;
}
/******************************************************************************
......@@ -5212,8 +5212,7 @@ e1000_validate_eeprom_checksum(struct e1000_hw *hw)
DEBUGFUNC("e1000_validate_eeprom_checksum");
if ((hw->mac_type == e1000_82573) &&
(e1000_is_onboard_nvm_eeprom(hw) == FALSE)) {
if ((hw->mac_type == e1000_82573) && !e1000_is_onboard_nvm_eeprom(hw)) {
/* Check bit 4 of word 10h. If it is 0, firmware is done updating
* 10h-12h. Checksum may need to be fixed. */
e1000_read_eeprom(hw, 0x10, 1, &eeprom_data);
......@@ -5339,7 +5338,7 @@ e1000_write_eeprom(struct e1000_hw *hw,
}
/* 82573 writes only through eewr */
if (eeprom->use_eewr == TRUE)
if (eeprom->use_eewr)
return e1000_write_eeprom_eewr(hw, offset, words, data);
if (eeprom->type == e1000_eeprom_ich8)
......@@ -5536,7 +5535,7 @@ e1000_commit_shadow_ram(struct e1000_hw *hw)
uint32_t new_bank_offset = 0;
uint8_t low_byte = 0;
uint8_t high_byte = 0;
boolean_t sector_write_failed = FALSE;
bool sector_write_failed = false;
if (hw->mac_type == e1000_82573) {
/* The flop register will be used to determine if flash type is STM */
......@@ -5588,21 +5587,21 @@ e1000_commit_shadow_ram(struct e1000_hw *hw)
e1000_erase_ich8_4k_segment(hw, 0);
}
sector_write_failed = FALSE;
sector_write_failed = false;
/* Loop for every byte in the shadow RAM,
* which is in units of words. */
for (i = 0; i < E1000_SHADOW_RAM_WORDS; i++) {
/* Determine whether to write the value stored
* in the other NVM bank or a modified value stored
* in the shadow RAM */
if (hw->eeprom_shadow_ram[i].modified == TRUE) {
if (hw->eeprom_shadow_ram[i].modified) {
low_byte = (uint8_t)hw->eeprom_shadow_ram[i].eeprom_word;
udelay(100);
error = e1000_verify_write_ich8_byte(hw,
(i << 1) + new_bank_offset, low_byte);
if (error != E1000_SUCCESS)
sector_write_failed = TRUE;
sector_write_failed = true;
else {
high_byte =
(uint8_t)(hw->eeprom_shadow_ram[i].eeprom_word >> 8);
......@@ -5616,7 +5615,7 @@ e1000_commit_shadow_ram(struct e1000_hw *hw)
(i << 1) + new_bank_offset, low_byte);
if (error != E1000_SUCCESS)
sector_write_failed = TRUE;
sector_write_failed = true;
else {
e1000_read_ich8_byte(hw, (i << 1) + old_bank_offset + 1,
&high_byte);
......@@ -5624,10 +5623,10 @@ e1000_commit_shadow_ram(struct e1000_hw *hw)
}
}
/* If the write of the low byte was successful, go ahread and
/* If the write of the low byte was successful, go ahead and
* write the high byte while checking to make sure that if it
* is the signature byte, then it is handled properly */
if (sector_write_failed == FALSE) {
if (!sector_write_failed) {
/* If the word is 0x13, then make sure the signature bits
* (15:14) are 11b until the commit has completed.
* This will allow us to write 10b which indicates the
......@@ -5640,7 +5639,7 @@ e1000_commit_shadow_ram(struct e1000_hw *hw)
error = e1000_verify_write_ich8_byte(hw,
(i << 1) + new_bank_offset + 1, high_byte);
if (error != E1000_SUCCESS)
sector_write_failed = TRUE;
sector_write_failed = true;
} else {
/* If the write failed then break from the loop and
......@@ -5651,7 +5650,7 @@ e1000_commit_shadow_ram(struct e1000_hw *hw)
/* Don't bother writing the segment valid bits if sector
* programming failed. */
if (sector_write_failed == FALSE) {
if (!sector_write_failed) {
/* Finally validate the new segment by setting bit 15:14
* to 10b in word 0x13 , this can be done without an
* erase as well since these bits are 11 to start with
......@@ -5673,7 +5672,7 @@ e1000_commit_shadow_ram(struct e1000_hw *hw)
/* Clear the now not used entry in the cache */
for (i = 0; i < E1000_SHADOW_RAM_WORDS; i++) {
hw->eeprom_shadow_ram[i].modified = FALSE;
hw->eeprom_shadow_ram[i].modified = false;
hw->eeprom_shadow_ram[i].eeprom_word = 0xFFFF;
}
}
......@@ -5750,7 +5749,7 @@ e1000_init_rx_addrs(struct e1000_hw *hw)
/* Reserve a spot for the Locally Administered Address to work around
* an 82571 issue in which a reset on one port will reload the MAC on
* the other port. */
if ((hw->mac_type == e1000_82571) && (hw->laa_is_present == TRUE))
if ((hw->mac_type == e1000_82571) && (hw->laa_is_present))
rar_num -= 1;
if (hw->mac_type == e1000_ich8lan)
rar_num = E1000_RAR_ENTRIES_ICH8LAN;
......@@ -5922,7 +5921,7 @@ e1000_rar_set(struct e1000_hw *hw,
case e1000_82571:
case e1000_82572:
case e1000_80003es2lan:
if (hw->leave_av_bit_off == TRUE)
if (hw->leave_av_bit_off)
break;
default:
/* Indicate to hardware the Address is Valid. */
......@@ -6425,7 +6424,7 @@ e1000_clear_hw_cntrs(struct e1000_hw *hw)
* hw - Struct containing variables accessed by shared code
*
* Call this after e1000_init_hw. You may override the IFS defaults by setting
* hw->ifs_params_forced to TRUE. However, you must initialize hw->
* hw->ifs_params_forced to true. However, you must initialize hw->
* current_ifs_val, ifs_min_val, ifs_max_val, ifs_step_size, and ifs_ratio
* before calling this function.
*****************************************************************************/
......@@ -6442,7 +6441,7 @@ e1000_reset_adaptive(struct e1000_hw *hw)
hw->ifs_step_size = IFS_STEP;
hw->ifs_ratio = IFS_RATIO;
}
hw->in_ifs_mode = FALSE;
hw->in_ifs_mode = false;
E1000_WRITE_REG(hw, AIT, 0);
} else {
DEBUGOUT("Not in Adaptive IFS mode!\n");
......@@ -6465,7 +6464,7 @@ e1000_update_adaptive(struct e1000_hw *hw)
if (hw->adaptive_ifs) {
if ((hw->collision_delta * hw->ifs_ratio) > hw->tx_packet_delta) {
if (hw->tx_packet_delta > MIN_NUM_XMITS) {
hw->in_ifs_mode = TRUE;
hw->in_ifs_mode = true;
if (hw->current_ifs_val < hw->ifs_max_val) {
if (hw->current_ifs_val == 0)
hw->current_ifs_val = hw->ifs_min_val;
......@@ -6477,7 +6476,7 @@ e1000_update_adaptive(struct e1000_hw *hw)
} else {
if (hw->in_ifs_mode && (hw->tx_packet_delta <= MIN_NUM_XMITS)) {
hw->current_ifs_val = 0;
hw->in_ifs_mode = FALSE;
hw->in_ifs_mode = false;
E1000_WRITE_REG(hw, AIT, 0);
}
}
......@@ -6968,7 +6967,7 @@ e1000_check_downshift(struct e1000_hw *hw)
M88E1000_PSSR_DOWNSHIFT_SHIFT;
} else if (hw->phy_type == e1000_phy_ife) {
/* e1000_phy_ife supports 10/100 speed only */
hw->speed_downgraded = FALSE;
hw->speed_downgraded = false;
}
return E1000_SUCCESS;
......@@ -6988,7 +6987,7 @@ e1000_check_downshift(struct e1000_hw *hw)
static int32_t
e1000_config_dsp_after_link_change(struct e1000_hw *hw,
boolean_t link_up)
bool link_up)
{
int32_t ret_val;
uint16_t phy_data, phy_saved_data, speed, duplex, i;
......@@ -7198,7 +7197,7 @@ e1000_set_phy_mode(struct e1000_hw *hw)
if (ret_val)
return ret_val;
hw->phy_reset_disable = FALSE;
hw->phy_reset_disable = false;
}
}
......@@ -7221,7 +7220,7 @@ e1000_set_phy_mode(struct e1000_hw *hw)
static int32_t
e1000_set_d3_lplu_state(struct e1000_hw *hw,
boolean_t active)
bool active)
{
uint32_t phy_ctrl = 0;
int32_t ret_val;
......@@ -7351,7 +7350,7 @@ e1000_set_d3_lplu_state(struct e1000_hw *hw,
static int32_t
e1000_set_d0_lplu_state(struct e1000_hw *hw,
boolean_t active)
bool active)
{
uint32_t phy_ctrl = 0;
int32_t ret_val;
......@@ -7689,9 +7688,9 @@ e1000_mng_write_commit(struct e1000_hw * hw)
/*****************************************************************************
* This function checks the mode of the firmware.
*
* returns - TRUE when the mode is IAMT or FALSE.
* returns - true when the mode is IAMT or false.
****************************************************************************/
boolean_t
bool
e1000_check_mng_mode(struct e1000_hw *hw)
{
uint32_t fwsm;
......@@ -7701,12 +7700,12 @@ e1000_check_mng_mode(struct e1000_hw *hw)
if (hw->mac_type == e1000_ich8lan) {
if ((fwsm & E1000_FWSM_MODE_MASK) ==
(E1000_MNG_ICH_IAMT_MODE << E1000_FWSM_MODE_SHIFT))
return TRUE;
return true;
} else if ((fwsm & E1000_FWSM_MODE_MASK) ==
(E1000_MNG_IAMT_MODE << E1000_FWSM_MODE_SHIFT))
return TRUE;
return true;
return FALSE;
return false;
}
......@@ -7763,15 +7762,15 @@ e1000_calculate_mng_checksum(char *buffer, uint32_t length)
/*****************************************************************************
* This function checks whether tx pkt filtering needs to be enabled or not.
*
* returns - TRUE for packet filtering or FALSE.
* returns - true for packet filtering or false.
****************************************************************************/
boolean_t
bool
e1000_enable_tx_pkt_filtering(struct e1000_hw *hw)
{
/* called in init as well as watchdog timer functions */
int32_t ret_val, checksum;
boolean_t tx_filter = FALSE;
bool tx_filter = false;
struct e1000_host_mng_dhcp_cookie *hdr = &(hw->mng_cookie);
uint8_t *buffer = (uint8_t *) &(hw->mng_cookie);
......@@ -7787,11 +7786,11 @@ e1000_enable_tx_pkt_filtering(struct e1000_hw *hw)
E1000_MNG_DHCP_COOKIE_LENGTH)) {
if (hdr->status &
E1000_MNG_DHCP_COOKIE_STATUS_PARSING_SUPPORT)
tx_filter = TRUE;
tx_filter = true;
} else
tx_filter = TRUE;
tx_filter = true;
} else
tx_filter = TRUE;
tx_filter = true;
}
}
......@@ -7804,7 +7803,7 @@ e1000_enable_tx_pkt_filtering(struct e1000_hw *hw)
*
* hw - Struct containing variables accessed by shared code
*
* returns: - TRUE/FALSE
* returns: - true/false
*
*****************************************************************************/
uint32_t
......@@ -7818,19 +7817,19 @@ e1000_enable_mng_pass_thru(struct e1000_hw *hw)
if (!(manc & E1000_MANC_RCV_TCO_EN) ||
!(manc & E1000_MANC_EN_MAC_ADDR_FILTER))
return FALSE;
if (e1000_arc_subsystem_valid(hw) == TRUE) {
return false;
if (e1000_arc_subsystem_valid(hw)) {
fwsm = E1000_READ_REG(hw, FWSM);
factps = E1000_READ_REG(hw, FACTPS);
if ((((fwsm & E1000_FWSM_MODE_MASK) >> E1000_FWSM_MODE_SHIFT) ==
e1000_mng_mode_pt) && !(factps & E1000_FACTPS_MNGCG))
return TRUE;
return true;
} else
if ((manc & E1000_MANC_SMBUS_EN) && !(manc & E1000_MANC_ASF_EN))
return TRUE;
return true;
}
return FALSE;
return false;
}
static int32_t
......@@ -8264,14 +8263,14 @@ e1000_arc_subsystem_valid(struct e1000_hw *hw)
case e1000_80003es2lan:
fwsm = E1000_READ_REG(hw, FWSM);
if ((fwsm & E1000_FWSM_MODE_MASK) != 0)
return TRUE;
return true;
break;
case e1000_ich8lan:
return TRUE;
return true;
default:
break;
}
return FALSE;
return false;
}
......@@ -8417,7 +8416,7 @@ e1000_read_eeprom_ich8(struct e1000_hw *hw, uint16_t offset, uint16_t words,
for (i = 0; i < words; i++) {
if (hw->eeprom_shadow_ram != NULL &&
hw->eeprom_shadow_ram[offset+i].modified == TRUE) {
hw->eeprom_shadow_ram[offset+i].modified) {
data[i] = hw->eeprom_shadow_ram[offset+i].eeprom_word;
} else {
/* The NVM part needs a byte offset, hence * 2 */
......@@ -8466,7 +8465,7 @@ e1000_write_eeprom_ich8(struct e1000_hw *hw, uint16_t offset, uint16_t words,
if (hw->eeprom_shadow_ram != NULL) {
for (i = 0; i < words; i++) {
if ((offset + i) < E1000_SHADOW_RAM_WORDS) {
hw->eeprom_shadow_ram[offset+i].modified = TRUE;
hw->eeprom_shadow_ram[offset+i].modified = true;
hw->eeprom_shadow_ram[offset+i].eeprom_word = data[i];
} else {
error = -E1000_ERR_EEPROM;
......
drivers/net/e1000/e1000_hw.h
View file @ c3033b01
......@@ -101,7 +101,7 @@ typedef enum {
struct e1000_shadow_ram {
uint16_t eeprom_word;
boolean_t modified;
bool modified;
};
/* PCI bus types */
......@@ -274,8 +274,8 @@ struct e1000_eeprom_info {
uint16_t address_bits;
uint16_t delay_usec;
uint16_t page_size;
boolean_t use_eerd;
boolean_t use_eewr;
bool use_eerd;
bool use_eewr;
};
/* Flex ASF Information */
......@@ -391,8 +391,8 @@ struct e1000_host_mng_dhcp_cookie{
int32_t e1000_mng_write_dhcp_info(struct e1000_hw *hw, uint8_t *buffer,
uint16_t length);
boolean_t e1000_check_mng_mode(struct e1000_hw *hw);
boolean_t e1000_enable_tx_pkt_filtering(struct e1000_hw *hw);
bool e1000_check_mng_mode(struct e1000_hw *hw);
bool e1000_enable_tx_pkt_filtering(struct e1000_hw *hw);
int32_t e1000_read_eeprom(struct e1000_hw *hw, uint16_t reg, uint16_t words, uint16_t *data);
int32_t e1000_validate_eeprom_checksum(struct e1000_hw *hw);
int32_t e1000_update_eeprom_checksum(struct e1000_hw *hw);
......@@ -1420,7 +1420,7 @@ struct e1000_hw {
uint32_t ledctl_default;
uint32_t ledctl_mode1;
uint32_t ledctl_mode2;
boolean_t tx_pkt_filtering;
bool tx_pkt_filtering;
struct e1000_host_mng_dhcp_cookie mng_cookie;
uint16_t phy_spd_default;
uint16_t autoneg_advertised;
......@@ -1445,30 +1445,30 @@ struct e1000_hw {
uint8_t dma_fairness;
uint8_t mac_addr[NODE_ADDRESS_SIZE];
uint8_t perm_mac_addr[NODE_ADDRESS_SIZE];
boolean_t disable_polarity_correction;
boolean_t speed_downgraded;
bool disable_polarity_correction;
bool speed_downgraded;
e1000_smart_speed smart_speed;
e1000_dsp_config dsp_config_state;
boolean_t get_link_status;
boolean_t serdes_link_down;
boolean_t tbi_compatibility_en;
boolean_t tbi_compatibility_on;
boolean_t laa_is_present;
boolean_t phy_reset_disable;
boolean_t initialize_hw_bits_disable;
boolean_t fc_send_xon;
boolean_t fc_strict_ieee;
boolean_t report_tx_early;
boolean_t adaptive_ifs;
boolean_t ifs_params_forced;
boolean_t in_ifs_mode;
boolean_t mng_reg_access_disabled;
boolean_t leave_av_bit_off;
boolean_t kmrn_lock_loss_workaround_disabled;
boolean_t bad_tx_carr_stats_fd;
boolean_t has_manc2h;
boolean_t rx_needs_kicking;
boolean_t has_smbus;
bool get_link_status;
bool serdes_link_down;
bool tbi_compatibility_en;
bool tbi_compatibility_on;
bool laa_is_present;
bool phy_reset_disable;
bool initialize_hw_bits_disable;
bool fc_send_xon;
bool fc_strict_ieee;
bool report_tx_early;
bool adaptive_ifs;
bool ifs_params_forced;
bool in_ifs_mode;
bool mng_reg_access_disabled;
bool leave_av_bit_off;
bool kmrn_lock_loss_workaround_disabled;
bool bad_tx_carr_stats_fd;
bool has_manc2h;
bool rx_needs_kicking;
bool has_smbus;
};
......@@ -2518,11 +2518,11 @@ struct e1000_host_command_info {
* Typical use:
* ...
* if (TBI_ACCEPT) {
* accept_frame = TRUE;
* accept_frame = true;
* e1000_tbi_adjust_stats(adapter, MacAddress);
* frame_length--;
* } else {
* accept_frame = FALSE;
* accept_frame = false;
* }
* ...
*/
......
drivers/net/e1000/e1000_main.c
View file @ c3033b01
......@@ -169,20 +169,20 @@ static int e1000_change_mtu(struct net_device *netdev, int new_mtu);
static int e1000_set_mac(struct net_device *netdev, void *p);
static irqreturn_t e1000_intr(int irq, void *data);
static irqreturn_t e1000_intr_msi(int irq, void *data);
static boolean_t e1000_clean_tx_irq(struct e1000_adapter *adapter,
static bool e1000_clean_tx_irq(struct e1000_adapter *adapter,
struct e1000_tx_ring *tx_ring);
#ifdef CONFIG_E1000_NAPI
static int e1000_clean(struct napi_struct *napi, int budget);
static boolean_t e1000_clean_rx_irq(struct e1000_adapter *adapter,
static bool e1000_clean_rx_irq(struct e1000_adapter *adapter,
struct e1000_rx_ring *rx_ring,
int *work_done, int work_to_do);
static boolean_t e1000_clean_rx_irq_ps(struct e1000_adapter *adapter,
static bool e1000_clean_rx_irq_ps(struct e1000_adapter *adapter,
struct e1000_rx_ring *rx_ring,
int *work_done, int work_to_do);
#else
static boolean_t e1000_clean_rx_irq(struct e1000_adapter *adapter,
static bool e1000_clean_rx_irq(struct e1000_adapter *adapter,
struct e1000_rx_ring *rx_ring);
static boolean_t e1000_clean_rx_irq_ps(struct e1000_adapter *adapter,
static bool e1000_clean_rx_irq_ps(struct e1000_adapter *adapter,
struct e1000_rx_ring *rx_ring);
#endif
static void e1000_alloc_rx_buffers(struct e1000_adapter *adapter,
......@@ -584,7 +584,7 @@ void e1000_power_up_phy(struct e1000_adapter *adapter)
static void e1000_power_down_phy(struct e1000_adapter *adapter)
{
/* Power down the PHY so no link is implied when interface is down *
* The PHY cannot be powered down if any of the following is TRUE *
* The PHY cannot be powered down if any of the following is true *
* (a) WoL is enabled
* (b) AMT is active
* (c) SoL/IDER session is active */
......@@ -673,7 +673,7 @@ e1000_reset(struct e1000_adapter *adapter)
{
uint32_t pba = 0, tx_space, min_tx_space, min_rx_space;
uint16_t fc_high_water_mark = E1000_FC_HIGH_DIFF;
boolean_t legacy_pba_adjust = FALSE;
bool legacy_pba_adjust = false;
/* Repartition Pba for greater than 9k mtu
* To take effect CTRL.RST is required.
......@@ -687,7 +687,7 @@ e1000_reset(struct e1000_adapter *adapter)
case e1000_82540:
case e1000_82541:
case e1000_82541_rev_2:
legacy_pba_adjust = TRUE;
legacy_pba_adjust = true;
pba = E1000_PBA_48K;
break;
case e1000_82545:
......@@ -698,7 +698,7 @@ e1000_reset(struct e1000_adapter *adapter)
break;
case e1000_82547:
case e1000_82547_rev_2:
legacy_pba_adjust = TRUE;
legacy_pba_adjust = true;
pba = E1000_PBA_30K;
break;
case e1000_82571:
......@@ -716,7 +716,7 @@ e1000_reset(struct e1000_adapter *adapter)
break;
}
if (legacy_pba_adjust == TRUE) {
if (legacy_pba_adjust) {
if (adapter->netdev->mtu > E1000_RXBUFFER_8192)
pba -= 8; /* allocate more FIFO for Tx */
......@@ -1366,15 +1366,15 @@ e1000_sw_init(struct e1000_adapter *adapter)
e1000_set_media_type(hw);
hw->wait_autoneg_complete = FALSE;
hw->tbi_compatibility_en = TRUE;
hw->adaptive_ifs = TRUE;
hw->wait_autoneg_complete = false;
hw->tbi_compatibility_en = true;
hw->adaptive_ifs = true;
/* Copper options */
if (hw->media_type == e1000_media_type_copper) {
hw->mdix = AUTO_ALL_MODES;
hw->disable_polarity_correction = FALSE;
hw->disable_polarity_correction = false;
hw->master_slave = E1000_MASTER_SLAVE;
}
......@@ -1576,7 +1576,7 @@ e1000_close(struct net_device *netdev)
* @start: address of beginning of memory
* @len: length of memory
**/
static boolean_t
static bool
e1000_check_64k_bound(struct e1000_adapter *adapter,
void *start, unsigned long len)
{
......@@ -1587,10 +1587,10 @@ e1000_check_64k_bound(struct e1000_adapter *adapter,
* write location to cross 64k boundary due to errata 23 */
if (adapter->hw.mac_type == e1000_82545 ||
adapter->hw.mac_type == e1000_82546) {
return ((begin ^ (end - 1)) >> 16) != 0 ? FALSE : TRUE;
return ((begin ^ (end - 1)) >> 16) != 0 ? false : true;
}
return TRUE;
return true;
}
/**
......@@ -2133,7 +2133,7 @@ e1000_configure_rx(struct e1000_adapter *adapter)
/* Enable 82543 Receive Checksum Offload for TCP and UDP */
if (hw->mac_type >= e1000_82543) {
rxcsum = E1000_READ_REG(hw, RXCSUM);
if (adapter->rx_csum == TRUE) {
if (adapter->rx_csum) {
rxcsum |= E1000_RXCSUM_TUOFL;
/* Enable 82571 IPv4 payload checksum for UDP fragments
......@@ -2669,7 +2669,7 @@ e1000_watchdog(unsigned long data)
if (link) {
if (!netif_carrier_ok(netdev)) {
uint32_t ctrl;
boolean_t txb2b = 1;
bool txb2b = true;
e1000_get_speed_and_duplex(&adapter->hw,
&adapter->link_speed,
&adapter->link_duplex);
......@@ -2691,12 +2691,12 @@ e1000_watchdog(unsigned long data)
adapter->tx_timeout_factor = 1;
switch (adapter->link_speed) {
case SPEED_10:
txb2b = 0;
txb2b = false;
netdev->tx_queue_len = 10;
adapter->tx_timeout_factor = 8;
break;
case SPEED_100:
txb2b = 0;
txb2b = false;
netdev->tx_queue_len = 100;
/* maybe add some timeout factor ? */
break;
......@@ -2704,7 +2704,7 @@ e1000_watchdog(unsigned long data)
if ((adapter->hw.mac_type == e1000_82571 ||
adapter->hw.mac_type == e1000_82572) &&
txb2b == 0) {
!txb2b) {
uint32_t tarc0;
tarc0 = E1000_READ_REG(&adapter->hw, TARC0);
tarc0 &= ~(1 << 21);
......@@ -2802,7 +2802,7 @@ e1000_watchdog(unsigned long data)
E1000_WRITE_REG(&adapter->hw, ICS, E1000_ICS_RXDMT0);
/* Force detection of hung controller every watchdog period */
adapter->detect_tx_hung = TRUE;
adapter->detect_tx_hung = true;
/* With 82571 controllers, LAA may be overwritten due to controller
* reset from the other port. Set the appropriate LAA in RAR[0] */
......@@ -3025,12 +3025,12 @@ e1000_tso(struct e1000_adapter *adapter, struct e1000_tx_ring *tx_ring,
if (++i == tx_ring->count) i = 0;
tx_ring->next_to_use = i;
return TRUE;
return true;
}
return FALSE;
return false;
}
static boolean_t
static bool
e1000_tx_csum(struct e1000_adapter *adapter, struct e1000_tx_ring *tx_ring,
struct sk_buff *skb)
{
......@@ -3060,10 +3060,10 @@ e1000_tx_csum(struct e1000_adapter *adapter, struct e1000_tx_ring *tx_ring,
if (unlikely(++i == tx_ring->count)) i = 0;
tx_ring->next_to_use = i;
return TRUE;
return true;
}
return FALSE;
return false;
}
#define E1000_MAX_TXD_PWR 12
......@@ -4038,7 +4038,7 @@ e1000_clean(struct napi_struct *napi, int budget)
* @adapter: board private structure
**/
static boolean_t
static bool
e1000_clean_tx_irq(struct e1000_adapter *adapter,
struct e1000_tx_ring *tx_ring)
{
......@@ -4049,7 +4049,7 @@ e1000_clean_tx_irq(struct e1000_adapter *adapter,
#ifdef CONFIG_E1000_NAPI
unsigned int count = 0;
#endif
boolean_t cleaned = FALSE;
bool cleaned = false;
unsigned int total_tx_bytes=0, total_tx_packets=0;
i = tx_ring->next_to_clean;
......@@ -4057,7 +4057,7 @@ e1000_clean_tx_irq(struct e1000_adapter *adapter,
eop_desc = E1000_TX_DESC(*tx_ring, eop);
while (eop_desc->upper.data & cpu_to_le32(E1000_TXD_STAT_DD)) {
for (cleaned = FALSE; !cleaned; ) {
for (cleaned = false; !cleaned; ) {
tx_desc = E1000_TX_DESC(*tx_ring, i);
buffer_info = &tx_ring->buffer_info[i];
cleaned = (i == eop);
......@@ -4105,7 +4105,7 @@ e1000_clean_tx_irq(struct e1000_adapter *adapter,
if (adapter->detect_tx_hung) {
/* Detect a transmit hang in hardware, this serializes the
* check with the clearing of time_stamp and movement of i */
adapter->detect_tx_hung = FALSE;
adapter->detect_tx_hung = false;
if (tx_ring->buffer_info[eop].dma &&
time_after(jiffies, tx_ring->buffer_info[eop].time_stamp +
(adapter->tx_timeout_factor * HZ))
......@@ -4200,7 +4200,7 @@ e1000_rx_checksum(struct e1000_adapter *adapter,
* @adapter: board private structure
**/
static boolean_t
static bool
#ifdef CONFIG_E1000_NAPI
e1000_clean_rx_irq(struct e1000_adapter *adapter,
struct e1000_rx_ring *rx_ring,
......@@ -4219,7 +4219,7 @@ e1000_clean_rx_irq(struct e1000_adapter *adapter,
uint8_t last_byte;
unsigned int i;
int cleaned_count = 0;
boolean_t cleaned = FALSE;
bool cleaned = false;
unsigned int total_rx_bytes=0, total_rx_packets=0;
i = rx_ring->next_to_clean;
......@@ -4247,7 +4247,7 @@ e1000_clean_rx_irq(struct e1000_adapter *adapter,
next_buffer = &rx_ring->buffer_info[i];
cleaned = TRUE;
cleaned = true;
cleaned_count++;
pci_unmap_single(pdev,
buffer_info->dma,
......@@ -4373,7 +4373,7 @@ e1000_clean_rx_irq(struct e1000_adapter *adapter,
* @adapter: board private structure
**/
static boolean_t
static bool
#ifdef CONFIG_E1000_NAPI
e1000_clean_rx_irq_ps(struct e1000_adapter *adapter,
struct e1000_rx_ring *rx_ring,
......@@ -4393,7 +4393,7 @@ e1000_clean_rx_irq_ps(struct e1000_adapter *adapter,
unsigned int i, j;
uint32_t length, staterr;
int cleaned_count = 0;
boolean_t cleaned = FALSE;
bool cleaned = false;
unsigned int total_rx_bytes=0, total_rx_packets=0;
i = rx_ring->next_to_clean;
......@@ -4420,7 +4420,7 @@ e1000_clean_rx_irq_ps(struct e1000_adapter *adapter,
next_buffer = &rx_ring->buffer_info[i];
cleaned = TRUE;
cleaned = true;
cleaned_count++;
pci_unmap_single(pdev, buffer_info->dma,
buffer_info->length,
......
drivers/net/e1000/e1000_osdep.h
View file @ c3033b01
......@@ -41,13 +41,6 @@
#include <linux/interrupt.h>
#include <linux/sched.h>
typedef enum {
#undef FALSE
FALSE = 0,
#undef TRUE
TRUE = 1
} boolean_t;
#ifdef DBG
#define DEBUGOUT(S) printk(KERN_DEBUG S "\n")
#define DEBUGOUT1(S, A...) printk(KERN_DEBUG S "\n", A)
......
Markdown is supported
0% or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment
GitLab Nexedi Edition | About GitLab | About Nexedi | 沪ICP备2021021310号-2 | 沪ICP备2021021310号-7