Merge branch 'for-rmk' of...

Merge branch 'for-rmk' of git://git.kernel.org/pub/scm/linux/kernel/git/ycmiao/pxa-linux-2.6 into devel

Conflicts:

	arch/arm/mach-pxa/pxa25x.c

arch/arm/boot/compressed/head.S

@@ -624,6 +624,12 @@ proc_types:
 		b	__armv4_mmu_cache_off
 		b	__armv4_mmu_cache_flush
 
+		.word	0x56056930
+		.word	0xff0ffff0		@ PXA935
+		b	__armv4_mmu_cache_on
+		b	__armv4_mmu_cache_off
+		b	__armv4_mmu_cache_flush
+
 		.word	0x56050000		@ Feroceon
 		.word	0xff0f0000
 		b	__armv4_mmu_cache_on

arch/arm/common/locomo.c

@@ -1108,6 +1108,7 @@ void locomo_frontlight_set(struct locomo_dev *dev, int duty, int vr, int bpwf)
 	locomo_writel(bpwf | LOCOMO_ALC_EN, lchip->base + LOCOMO_FRONTLIGHT + LOCOMO_ALS);
 	spin_unlock_irqrestore(&lchip->lock, flags);
 }
+EXPORT_SYMBOL(locomo_frontlight_set);
 
 /*
  *	LoCoMo "Register Access Bus."

arch/arm/mach-pxa/Kconfig

@@ -19,6 +19,9 @@ config CPU_PXA320
 config CPU_PXA930
 	bool "PXA930 (codename Tavor-P)"
 
+config CPU_PXA935
+	bool "PXA935 (codename Tavor-P65)"
+
 endmenu
 
 endif
@@ -199,6 +202,10 @@ config MACH_E800
 config TRIZEPS_PXA
 	bool "PXA based Keith und Koep Trizeps DIMM-Modules"
 
+config MACH_H5000
+	bool "HP iPAQ h5000"
+	select PXA25x
+
 config MACH_TRIZEPS4
 	bool "Keith und Koep Trizeps4 DIMM-Module"
 	depends on TRIZEPS_PXA
@@ -283,7 +290,6 @@ config MACH_MIOA701
 	bool "Mitac Mio A701 Support"
 	select PXA27x
 	select IWMMXT
-	select LEDS_GPIO
 	select HAVE_PWM
 	select GPIO_SYSFS
 	help
@@ -396,6 +402,12 @@ config PXA27x
 	help
 	  Select code specific to PXA27x variants
 
+config CPU_PXA26x
+	bool
+	select PXA25x
+	help
+	  Select code specific to PXA26x (codename Dalhart)
+
 config PXA3xx
 	bool
 	select CPU_XSC3

arch/arm/mach-pxa/Makefile

@@ -35,6 +35,7 @@ obj-$(CONFIG_MACH_MP900C)	+= mp900.o
 obj-$(CONFIG_ARCH_PXA_IDP)	+= idp.o
 obj-$(CONFIG_MACH_TRIZEPS4)	+= trizeps4.o
 obj-$(CONFIG_MACH_COLIBRI)	+= colibri.o
+obj-$(CONFIG_MACH_H5000)	+= h5000.o
 obj-$(CONFIG_PXA_SHARP_C7xx)	+= corgi.o sharpsl_pm.o corgi_pm.o
 obj-$(CONFIG_PXA_SHARP_Cxx00)	+= spitz.o sharpsl_pm.o spitz_pm.o
 obj-$(CONFIG_CORGI_SSP_DEPRECATED)	+= corgi_ssp.o corgi_lcd.o

arch/arm/mach-pxa/clock.c

@@ -14,7 +14,6 @@
 
 #include <asm/clkdev.h>
 #include <mach/pxa2xx-regs.h>
-#include <mach/pxa2xx-gpio.h>
 #include <mach/hardware.h>
 
 #include "devices.h"

arch/arm/mach-pxa/cm-x300.c

@@ -31,7 +31,6 @@
 #include <mach/mfp-pxa300.h>
 
 #include <mach/hardware.h>
-#include <mach/gpio.h>
 #include <mach/pxafb.h>
 #include <mach/mmc.h>
 #include <mach/ohci.h>
@@ -137,6 +136,10 @@ static mfp_cfg_t cm_x300_mfp_cfg[] __initdata = {
 	GPIO82_GPIO | MFP_PULL_HIGH,	/* MMC CD */
 	GPIO85_GPIO,			/* MMC WP */
 	GPIO99_GPIO,			/* Ethernet IRQ */
+
+	/* Standard I2C */
+	GPIO21_I2C_SCL,
+	GPIO22_I2C_SDA,
 };
 
 #if defined(CONFIG_DM9000) || defined(CONFIG_DM9000_MODULE)

arch/arm/mach-pxa/corgi.c

@@ -19,6 +19,7 @@
 #include <linux/fs.h>
 #include <linux/interrupt.h>
 #include <linux/mmc/host.h>
+#include <linux/mtd/physmap.h>
 #include <linux/pm.h>
 #include <linux/gpio.h>
 #include <linux/backlight.h>
@@ -541,11 +542,42 @@ static void __init corgi_init_spi(void)
 static inline void corgi_init_spi(void) {}
 #endif
 
+static struct mtd_partition sharpsl_rom_parts[] = {
+	{
+		.name	="Boot PROM Filesystem",
+		.offset	= 0x00120000,
+		.size	= MTDPART_SIZ_FULL,
+	},
+};
+
+static struct physmap_flash_data sharpsl_rom_data = {
+	.width		= 2,
+	.nr_parts	= ARRAY_SIZE(sharpsl_rom_parts),
+	.parts		= sharpsl_rom_parts,
+};
+
+static struct resource sharpsl_rom_resources[] = {
+	{
+		.start	= 0x00000000,
+		.end	= 0x007fffff,
+		.flags	= IORESOURCE_MEM,
+	},
+};
+
+static struct platform_device sharpsl_rom_device = {
+	.name	= "physmap-flash",
+	.id	= -1,
+	.resource = sharpsl_rom_resources,
+	.num_resources = ARRAY_SIZE(sharpsl_rom_resources),
+	.dev.platform_data = &sharpsl_rom_data,
+};
+
 static struct platform_device *devices[] __initdata = {
 	&corgiscoop_device,
 	&corgifb_device,
 	&corgikbd_device,
 	&corgiled_device,
+	&sharpsl_rom_device,
 };
 
 static void corgi_poweroff(void)

arch/arm/mach-pxa/cpufreq-pxa2xx.c

@@ -64,7 +64,7 @@ typedef struct {
 
 /* Define the refresh period in mSec for the SDRAM and the number of rows */
 #define SDRAM_TREF	64	/* standard 64ms SDRAM */
-#define SDRAM_ROWS	4096	/* 64MB=8192 32MB=4096 */
+static unsigned int sdram_rows;
 
 #define CCLKCFG_TURBO		0x1
 #define CCLKCFG_FCS		0x2
@@ -73,6 +73,9 @@ typedef struct {
 #define MDREFR_DB2_MASK		(MDREFR_K2DB2 | MDREFR_K1DB2)
 #define MDREFR_DRI_MASK		0xFFF
 
+#define MDCNFG_DRAC2(mdcnfg) (((mdcnfg) >> 21) & 0x3)
+#define MDCNFG_DRAC0(mdcnfg) (((mdcnfg) >> 5) & 0x3)
+
 /*
  * PXA255 definitions
  */
@@ -109,6 +112,10 @@ static struct cpufreq_frequency_table
 static struct cpufreq_frequency_table
 	pxa255_turbo_freq_table[NUM_PXA25x_TURBO_FREQS+1];
 
+static unsigned int pxa255_turbo_table;
+module_param(pxa255_turbo_table, uint, 0);
+MODULE_PARM_DESC(pxa255_turbo_table, "Selects the frequency table (0 = run table, !0 = turbo table)");
+
 /*
  * PXA270 definitions
  *
@@ -158,22 +165,16 @@ static struct cpufreq_frequency_table
 
 extern unsigned get_clk_frequency_khz(int info);
 
-static void find_freq_tables(struct cpufreq_policy *policy,
-			     struct cpufreq_frequency_table **freq_table,
+static void find_freq_tables(struct cpufreq_frequency_table **freq_table,
 			     pxa_freqs_t **pxa_freqs)
 {
 	if (cpu_is_pxa25x()) {
-		if (policy->policy == CPUFREQ_POLICY_PERFORMANCE) {
+		if (!pxa255_turbo_table) {
 			*pxa_freqs = pxa255_run_freqs;
 			*freq_table = pxa255_run_freq_table;
-		} else if (policy->policy == CPUFREQ_POLICY_POWERSAVE) {
+		} else {
 			*pxa_freqs = pxa255_turbo_freqs;
 			*freq_table = pxa255_turbo_freq_table;
-		} else {
-			printk("CPU PXA: Unknown policy found. "
-			       "Using CPUFREQ_POLICY_PERFORMANCE\n");
-			*pxa_freqs = pxa255_run_freqs;
-			*freq_table = pxa255_run_freq_table;
 		}
 	}
 	if (cpu_is_pxa27x()) {
@@ -194,14 +195,28 @@ static void pxa27x_guess_max_freq(void)
 	}
 }
 
+static void init_sdram_rows(void)
+{
+	uint32_t mdcnfg = MDCNFG;
+	unsigned int drac2 = 0, drac0 = 0;
+
+	if (mdcnfg & (MDCNFG_DE2 | MDCNFG_DE3))
+		drac2 = MDCNFG_DRAC2(mdcnfg);
+
+	if (mdcnfg & (MDCNFG_DE0 | MDCNFG_DE1))
+		drac0 = MDCNFG_DRAC0(mdcnfg);
+
+	sdram_rows = 1 << (11 + max(drac0, drac2));
+}
+
 static u32 mdrefr_dri(unsigned int freq)
 {
 	u32 dri = 0;
 
 	if (cpu_is_pxa25x())
-		dri = ((freq * SDRAM_TREF) / (SDRAM_ROWS * 32));
+		dri = ((freq * SDRAM_TREF) / (sdram_rows * 32));
 	if (cpu_is_pxa27x())
-		dri = ((freq * SDRAM_TREF) / (SDRAM_ROWS - 31)) / 32;
+		dri = ((freq * SDRAM_TREF) / (sdram_rows - 31)) / 32;
 	return dri;
 }
 
@@ -212,7 +227,7 @@ static int pxa_verify_policy(struct cpufreq_policy *policy)
 	pxa_freqs_t *pxa_freqs;
 	int ret;
 
-	find_freq_tables(policy, &pxa_freqs_table, &pxa_freqs);
+	find_freq_tables(&pxa_freqs_table, &pxa_freqs);
 	ret = cpufreq_frequency_table_verify(policy, pxa_freqs_table);
 
 	if (freq_debug)
@@ -240,7 +255,7 @@ static int pxa_set_target(struct cpufreq_policy *policy,
 	unsigned int unused, preset_mdrefr, postset_mdrefr, cclkcfg;
 
 	/* Get the current policy */
-	find_freq_tables(policy, &pxa_freqs_table, &pxa_freq_settings);
+	find_freq_tables(&pxa_freqs_table, &pxa_freq_settings);
 
 	/* Lookup the next frequency */
 	if (cpufreq_frequency_table_target(policy, pxa_freqs_table,
@@ -329,11 +344,15 @@ static __init int pxa_cpufreq_init(struct cpufreq_policy *policy)
 {
 	int i;
 	unsigned int freq;
+	struct cpufreq_frequency_table *pxa255_freq_table;
+	pxa_freqs_t *pxa255_freqs;
 
 	/* try to guess pxa27x cpu */
 	if (cpu_is_pxa27x())
 		pxa27x_guess_max_freq();
 
+	init_sdram_rows();
+
 	/* set default policy and cpuinfo */
 	policy->cpuinfo.transition_latency = 1000; /* FIXME: 1 ms, assumed */
 	policy->cur = get_clk_frequency_khz(0);	   /* current freq */
@@ -354,6 +373,8 @@ static __init int pxa_cpufreq_init(struct cpufreq_policy *policy)
 	}
 	pxa255_turbo_freq_table[i].frequency = CPUFREQ_TABLE_END;
 
+	pxa255_turbo_table = !!pxa255_turbo_table;
+
 	/* Generate the pxa27x cpufreq_frequency_table struct */
 	for (i = 0; i < NUM_PXA27x_FREQS; i++) {
 		freq = pxa27x_freqs[i].khz;
@@ -368,8 +389,12 @@ static __init int pxa_cpufreq_init(struct cpufreq_policy *policy)
 	 * Set the policy's minimum and maximum frequencies from the tables
 	 * just constructed.  This sets cpuinfo.mxx_freq, min and max.
 	 */
-	if (cpu_is_pxa25x())
-		cpufreq_frequency_table_cpuinfo(policy, pxa255_run_freq_table);
+	if (cpu_is_pxa25x()) {
+		find_freq_tables(&pxa255_freq_table, &pxa255_freqs);
+		pr_info("PXA255 cpufreq using %s frequency table\n",
+			pxa255_turbo_table ? "turbo" : "run");
+		cpufreq_frequency_table_cpuinfo(policy, pxa255_freq_table);
+	}
 	else if (cpu_is_pxa27x())
 		cpufreq_frequency_table_cpuinfo(policy, pxa27x_freq_table);
 

arch/arm/mach-pxa/devices.c

@@ -4,13 +4,12 @@
 #include <linux/platform_device.h>
 #include <linux/dma-mapping.h>
 
-#include <mach/gpio.h>
+#include <mach/pxa-regs.h>
 #include <mach/udc.h>
 #include <mach/pxafb.h>
 #include <mach/mmc.h>
 #include <mach/irda.h>
 #include <mach/i2c.h>
-#include <mach/mfp-pxa27x.h>
 #include <mach/ohci.h>
 #include <mach/pxa27x_keypad.h>
 #include <mach/pxa2xx_spi.h>
@@ -156,8 +155,8 @@ void __init set_pxa_fb_parent(struct device *parent_dev)
 
 static struct resource pxa_resource_ffuart[] = {
 	{
-		.start	= __PREG(FFUART),
-		.end	= __PREG(FFUART) + 35,
+		.start	= 0x40100000,
+		.end	= 0x40100023,
 		.flags	= IORESOURCE_MEM,
 	}, {
 		.start	= IRQ_FFUART,
@@ -175,8 +174,8 @@ struct platform_device pxa_device_ffuart= {
 
 static struct resource pxa_resource_btuart[] = {
 	{
-		.start	= __PREG(BTUART),
-		.end	= __PREG(BTUART) + 35,
+		.start	= 0x40200000,
+		.end	= 0x40200023,
 		.flags	= IORESOURCE_MEM,
 	}, {
 		.start	= IRQ_BTUART,
@@ -194,8 +193,8 @@ struct platform_device pxa_device_btuart = {
 
 static struct resource pxa_resource_stuart[] = {
 	{
-		.start	= __PREG(STUART),
-		.end	= __PREG(STUART) + 35,
+		.start	= 0x40700000,
+		.end	= 0x40700023,
 		.flags	= IORESOURCE_MEM,
 	}, {
 		.start	= IRQ_STUART,
@@ -213,8 +212,8 @@ struct platform_device pxa_device_stuart = {
 
 static struct resource pxa_resource_hwuart[] = {
 	{
-		.start	= __PREG(HWUART),
-		.end	= __PREG(HWUART) + 47,
+		.start	= 0x41600000,
+		.end	= 0x4160002F,
 		.flags	= IORESOURCE_MEM,
 	}, {
 		.start	= IRQ_HWUART,
@@ -249,18 +248,53 @@ struct platform_device pxa_device_i2c = {
 	.num_resources	= ARRAY_SIZE(pxai2c_resources),
 };
 
-static unsigned long pxa27x_i2c_mfp_cfg[] = {
-	GPIO117_I2C_SCL,
-	GPIO118_I2C_SDA,
-};
-
 void __init pxa_set_i2c_info(struct i2c_pxa_platform_data *info)
 {
-	if (cpu_is_pxa27x())
-		pxa2xx_mfp_config(ARRAY_AND_SIZE(pxa27x_i2c_mfp_cfg));
 	pxa_register_device(&pxa_device_i2c, info);
 }
 
+#ifdef CONFIG_PXA27x
+static struct resource pxa27x_resources_i2c_power[] = {
+	{
+		.start	= 0x40f00180,
+		.end	= 0x40f001a3,
+		.flags	= IORESOURCE_MEM,
+	}, {
+		.start	= IRQ_PWRI2C,
+		.end	= IRQ_PWRI2C,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+struct platform_device pxa27x_device_i2c_power = {
+	.name		= "pxa2xx-i2c",
+	.id		= 1,
+	.resource	= pxa27x_resources_i2c_power,
+	.num_resources	= ARRAY_SIZE(pxa27x_resources_i2c_power),
+};
+#endif
+
+#ifdef CONFIG_PXA3xx
+static struct resource pxa3xx_resources_i2c_power[] = {
+	{
+		.start  = 0x40f500c0,
+		.end    = 0x40f500d3,
+		.flags	= IORESOURCE_MEM,
+	}, {
+		.start	= IRQ_PWRI2C,
+		.end	= IRQ_PWRI2C,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+struct platform_device pxa3xx_device_i2c_power = {
+	.name		= "pxa2xx-i2c",
+	.id		= 1,
+	.resource	= pxa3xx_resources_i2c_power,
+	.num_resources	= ARRAY_SIZE(pxa3xx_resources_i2c_power),
+};
+#endif
+
 static struct resource pxai2s_resources[] = {
 	{
 		.start	= 0x40400000,
@@ -296,11 +330,36 @@ void __init pxa_set_ficp_info(struct pxaficp_platform_data *info)
 	pxa_register_device(&pxa_device_ficp, info);
 }
 
-struct platform_device pxa_device_rtc = {
+static struct resource pxa_rtc_resources[] = {
+	[0] = {
+		.start  = 0x40900000,
+		.end	= 0x40900000 + 0x3b,
+		.flags  = IORESOURCE_MEM,
+	},
+	[1] = {
+		.start  = IRQ_RTC1Hz,
+		.end    = IRQ_RTC1Hz,
+		.flags  = IORESOURCE_IRQ,
+	},
+	[2] = {
+		.start  = IRQ_RTCAlrm,
+		.end    = IRQ_RTCAlrm,
+		.flags  = IORESOURCE_IRQ,
+	},
+};
+
+struct platform_device sa1100_device_rtc = {
 	.name		= "sa1100-rtc",
 	.id		= -1,
 };
 
+struct platform_device pxa_device_rtc = {
+	.name		= "pxa-rtc",
+	.id		= -1,
+	.num_resources  = ARRAY_SIZE(pxa_rtc_resources),
+	.resource       = pxa_rtc_resources,
+};
+
 static struct resource pxa_ac97_resources[] = {
 	[0] = {
 		.start  = 0x40500000,

arch/arm/mach-pxa/devices.h

@@ -11,6 +11,7 @@ extern struct platform_device pxa_device_hwuart;
 extern struct platform_device pxa_device_i2c;
 extern struct platform_device pxa_device_i2s;
 extern struct platform_device pxa_device_ficp;
+extern struct platform_device sa1100_device_rtc;
 extern struct platform_device pxa_device_rtc;
 extern struct platform_device pxa_device_ac97;
 

arch/arm/mach-pxa/ezx.c

@@ -113,6 +113,10 @@ static unsigned long ezx_pin_config[] __initdata = {
 	GPIO91_USB_P3_1,	/* ICL_XRXD */
 	GPIO56_USB_P3_4,	/* ICL_VMOUT */
 	GPIO113_USB_P3_3,	/* /ICL_VMIN */
+
+	/* I2C */
+	GPIO117_I2C_SCL,
+	GPIO118_I2C_SDA,
 };
 
 static void __init ezx_init(void)

arch/arm/mach-pxa/gpio.c

@@ -25,6 +25,18 @@
 
 #include "generic.h"
 
+#define GPIO0_BASE	((void __iomem *)io_p2v(0x40E00000))
+#define GPIO1_BASE	((void __iomem *)io_p2v(0x40E00004))
+#define GPIO2_BASE	((void __iomem *)io_p2v(0x40E00008))
+#define GPIO3_BASE	((void __iomem *)io_p2v(0x40E00100))
+
+#define GPLR_OFFSET	0x00
+#define GPDR_OFFSET	0x0C
+#define GPSR_OFFSET	0x18
+#define GPCR_OFFSET	0x24
+#define GRER_OFFSET	0x30
+#define GFER_OFFSET	0x3C
+#define GEDR_OFFSET	0x48
 
 struct pxa_gpio_chip {
 	struct gpio_chip chip;
@@ -33,6 +45,18 @@ struct pxa_gpio_chip {
 
 int pxa_last_gpio;
 
+#ifdef CONFIG_CPU_PXA26x
+/* GPIO86/87/88/89 on PXA26x have their direction bits in GPDR2 inverted,
+ * as well as their Alternate Function value being '1' for GPIO in GAFRx.
+ */
+static int __gpio_is_inverted(unsigned gpio)
+{
+	return cpu_is_pxa25x() && gpio > 85;
+}
+#else
+#define __gpio_is_inverted(gpio)	(0)
+#endif
+
 /*
  * Configure pins for GPIO or other functions
  */
@@ -75,7 +99,10 @@ static int pxa_gpio_direction_input(struct gpio_chip *chip, unsigned offset)
 	gpdr = pxa->regbase + GPDR_OFFSET;
 	local_irq_save(flags);
 	value = __raw_readl(gpdr);
-	value &= ~mask;
+	if (__gpio_is_inverted(chip->base + offset))
+		value |= mask;
+	else
+		value &= ~mask;
 	__raw_writel(value, gpdr);
 	local_irq_restore(flags);
 
@@ -97,7 +124,10 @@ static int pxa_gpio_direction_output(struct gpio_chip *chip,
 	gpdr = pxa->regbase + GPDR_OFFSET;
 	local_irq_save(flags);
 	tmp = __raw_readl(gpdr);
-	tmp |= mask;
+	if (__gpio_is_inverted(chip->base + offset))
+		tmp &= ~mask;
+	else
+		tmp |= mask;
 	__raw_writel(tmp, gpdr);
 	local_irq_restore(flags);
 
@@ -173,10 +203,17 @@ static unsigned long GPIO_IRQ_mask[4];
  */
 static int __gpio_is_occupied(unsigned gpio)
 {
-	if (cpu_is_pxa25x() || cpu_is_pxa27x())
-		return GAFR(gpio) & (0x3 << (((gpio) & 0xf) * 2));
-	else
-		return 0;
+	if (cpu_is_pxa27x() || cpu_is_pxa25x()) {
+		int af = (GAFR(gpio) >> ((gpio & 0xf) * 2)) & 0x3;
+		int dir = GPDR(gpio) & GPIO_bit(gpio);
+
+		if (__gpio_is_inverted(gpio))
+			return af != 1 || dir == 0;
+		else
+			return af != 0 || dir != 0;
+	}
+
+	return 0;
 }
 
 static int pxa_gpio_irq_type(unsigned int irq, unsigned int type)
@@ -190,9 +227,8 @@ static int pxa_gpio_irq_type(unsigned int irq, unsigned int type)
 		/* Don't mess with enabled GPIOs using preconfigured edges or
 		 * GPIOs set to alternate function or to output during probe
 		 */
-		if ((GPIO_IRQ_rising_edge[idx] |
-		     GPIO_IRQ_falling_edge[idx] |
-		     GPDR(gpio)) & GPIO_bit(gpio))
+		if ((GPIO_IRQ_rising_edge[idx] & GPIO_bit(gpio)) ||
+		    (GPIO_IRQ_falling_edge[idx] & GPIO_bit(gpio)))
 			return 0;
 
 		if (__gpio_is_occupied(gpio))
@@ -201,7 +237,10 @@ static int pxa_gpio_irq_type(unsigned int irq, unsigned int type)
 		type = IRQ_TYPE_EDGE_RISING | IRQ_TYPE_EDGE_FALLING;
 	}
 
-	GPDR(gpio) &= ~GPIO_bit(gpio);
+	if (__gpio_is_inverted(gpio))
+		GPDR(gpio) |= GPIO_bit(gpio);
+	else
+		GPDR(gpio) &= ~GPIO_bit(gpio);
 
 	if (type & IRQ_TYPE_EDGE_RISING)
 		__set_bit(gpio, GPIO_IRQ_rising_edge);

arch/arm/mach-pxa/h5000.c

+/*
+ * Hardware definitions for HP iPAQ h5xxx Handheld Computers
+ *
+ * Copyright 2000-2003  Hewlett-Packard Company.
+ * Copyright 2002       Jamey Hicks <jamey.hicks@hp.com>
+ * Copyright 2004-2005  Phil Blundell <pb@handhelds.org>
+ * Copyright 2007-2008  Anton Vorontsov <cbouatmailru@gmail.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * COMPAQ COMPUTER CORPORATION MAKES NO WARRANTIES, EXPRESSED OR IMPLIED,
+ * AS TO THE USEFULNESS OR CORRECTNESS OF THIS CODE OR ITS
+ * FITNESS FOR ANY PARTICULAR PURPOSE.
+ *
+ * Author: Jamey Hicks.
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/partitions.h>
+#include <linux/mtd/physmap.h>
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+#include <mach/h5000.h>
+#include <mach/pxa-regs.h>
+#include <mach/pxa2xx-regs.h>
+#include <mach/mfp-pxa25x.h>
+#include <mach/udc.h>
+#include "generic.h"
+
+/*
+ * Flash
+ */
+
+static struct mtd_partition h5000_flash0_partitions[] = {
+	{
+		.name = "bootldr",
+		.size = 0x00040000,
+		.offset = 0,
+		.mask_flags = MTD_WRITEABLE,
+	},
+	{
+		.name = "root",
+		.size = MTDPART_SIZ_FULL,
+		.offset = MTDPART_OFS_APPEND,
+	},
+};
+
+static struct mtd_partition h5000_flash1_partitions[] = {
+	{
+		.name = "second root",
+		.size = SZ_16M - 0x00040000,
+		.offset = 0,
+	},
+	{
+		.name = "asset",
+		.size = MTDPART_SIZ_FULL,
+		.offset = MTDPART_OFS_APPEND,
+		.mask_flags = MTD_WRITEABLE,
+	},
+};
+
+static struct physmap_flash_data h5000_flash0_data = {
+	.width = 4,
+	.parts = h5000_flash0_partitions,
+	.nr_parts = ARRAY_SIZE(h5000_flash0_partitions),
+};
+
+static struct physmap_flash_data h5000_flash1_data = {
+	.width = 4,
+	.parts = h5000_flash1_partitions,
+	.nr_parts = ARRAY_SIZE(h5000_flash1_partitions),
+};
+
+static struct resource h5000_flash0_resources = {
+	.start = PXA_CS0_PHYS,
+	.end = PXA_CS0_PHYS + SZ_32M - 1,
+	.flags = IORESOURCE_MEM | IORESOURCE_MEM_32BIT,
+};
+
+static struct resource h5000_flash1_resources = {
+	.start = PXA_CS0_PHYS + SZ_32M,
+	.end = PXA_CS0_PHYS + SZ_32M + SZ_16M - 1,
+	.flags = IORESOURCE_MEM | IORESOURCE_MEM_32BIT,
+};
+
+static struct platform_device h5000_flash[] = {
+	{
+		.name = "physmap-flash",
+		.id = 0,
+		.resource = &h5000_flash0_resources,
+		.num_resources = 1,
+		.dev = {
+			.platform_data = &h5000_flash0_data,
+		},
+	},
+	{
+		.name = "physmap-flash",
+		.id = 1,
+		.resource = &h5000_flash1_resources,
+		.num_resources = 1,
+		.dev = {
+			.platform_data = &h5000_flash1_data,
+		},
+	},
+};
+
+/*
+ * USB Device Controller
+ */
+
+static struct pxa2xx_udc_mach_info h5000_udc_mach_info __initdata = {
+	.gpio_pullup = H5000_GPIO_USB_PULLUP,
+};
+
+/*
+ * GPIO setup
+ */
+
+static unsigned long h5000_pin_config[] __initdata = {
+	/* Crystal and Clock Signals */
+	GPIO12_32KHz,
+
+	/* SDRAM and Static Memory I/O Signals */
+	GPIO15_nCS_1,
+	GPIO78_nCS_2,
+	GPIO79_nCS_3,
+	GPIO80_nCS_4,
+
+	/* FFUART */
+	GPIO34_FFUART_RXD,
+	GPIO35_FFUART_CTS,
+	GPIO36_FFUART_DCD,
+	GPIO37_FFUART_DSR,
+	GPIO38_FFUART_RI,
+	GPIO39_FFUART_TXD,
+	GPIO40_FFUART_DTR,
+	GPIO41_FFUART_RTS,
+
+	/* BTUART */
+	GPIO42_BTUART_RXD,
+	GPIO43_BTUART_TXD,
+	GPIO44_BTUART_CTS,
+	GPIO45_BTUART_RTS,
+
+	/* SSP1 */
+	GPIO23_SSP1_SCLK,
+	GPIO25_SSP1_TXD,
+	GPIO26_SSP1_RXD,
+};
+
+/*
+ * Localbus setup:
+ * CS0: Flash;
+ * CS1: MediaQ chip, select 16-bit bus and vlio;
+ * CS5: SAMCOP.
+ */
+
+static void fix_msc(void)
+{
+	MSC0 = 0x129c24f2;
+	MSC1 = 0x7ff424fa;
+	MSC2 = 0x7ff47ff4;
+
+	MDREFR |= 0x02080000;
+}
+
+/*
+ * Platform devices
+ */
+
+static struct platform_device *devices[] __initdata = {
+	&h5000_flash[0],
+	&h5000_flash[1],
+};
+
+static void __init h5000_init(void)
+{
+	fix_msc();
+
+	pxa2xx_mfp_config(ARRAY_AND_SIZE(h5000_pin_config));
+	pxa_set_udc_info(&h5000_udc_mach_info);
+	platform_add_devices(ARRAY_AND_SIZE(devices));
+}
+
+MACHINE_START(H5400, "HP iPAQ H5000")
+	.phys_io = 0x40000000,
+	.io_pg_offst = (io_p2v(0x40000000) >> 18) & 0xfffc,
+	.boot_params = 0xa0000100,
+	.map_io = pxa_map_io,
+	.init_irq = pxa25x_init_irq,
+	.timer = &pxa_timer,
+	.init_machine = h5000_init,
+MACHINE_END

arch/arm/mach-pxa/include/mach/h5000.h

+/*
+ * Hardware definitions for HP iPAQ h5xxx Handheld Computers
+ *
+ * Copyright(20)02 Hewlett-Packard Company.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * COMPAQ COMPUTER CORPORATION MAKES NO WARRANTIES, EXPRESSED OR IMPLIED,
+ * AS TO THE USEFULNESS OR CORRECTNESS OF THIS CODE OR ITS
+ * FITNESS FOR ANY PARTICULAR PURPOSE.
+ *
+ * Author: Jamey Hicks
+ */
+
+#ifndef __ASM_ARCH_H5000_H
+#define __ASM_ARCH_H5000_H
+
+#include <mach/mfp-pxa25x.h>
+
+/*
+ * CPU GPIOs
+ */
+
+#define H5000_GPIO_POWER_BUTTON   (0)
+#define H5000_GPIO_RESET_BUTTON_N (1)
+#define H5000_GPIO_OPT_INT        (2)
+#define H5000_GPIO_BACKUP_POWER   (3)
+#define H5000_GPIO_ACTION_BUTTON  (4)
+#define H5000_GPIO_COM_DCD_SOMETHING  (5) /* what is this really ? */
+/* 6 not connected */
+#define H5000_GPIO_RESET_BUTTON_AGAIN_N (7) /* connected to gpio 1 as well */
+/* 8 not connected */
+#define H5000_GPIO_RSO_N          (9)       /* reset output from max1702 which regulates 3.3 and 2.5 */
+#define H5000_GPIO_ASIC_INT_N   (10)       /* from companion asic */
+#define H5000_GPIO_BT_ENV_0     (11)       /* to LMX9814, set to 1 according to regdump */
+/*(12) not connected */
+#define H5000_GPIO_BT_ENV_1     (13)       /* to LMX9814, set to 1 according to regdump */
+#define H5000_GPIO_BT_WU        (14)       /* from LMX9814, Defined as HOST_WAKEUP in the LMX9820 data sheet */
+/*(15) is CS1# */
+/*(16) not connected */
+/*(17) not connected */
+/*(18) is pcmcia ready */
+/*(19) is dreq1 */
+/*(20) is dreq0 */
+#define H5000_GPIO_OE_RD_NWR	(21)       /* output enable on rd/nwr signal to companion asic */
+/*(22) is not connected */
+#define H5000_GPIO_OPT_SPI_CLK  (23)       /* to extension pack */
+#define H5000_GPIO_OPT_SPI_CS_N (24)       /* to extension pack */
+#define H5000_GPIO_OPT_SPI_DOUT (25)       /* to extension pack */
+#define H5000_GPIO_OPT_SPI_DIN  (26)       /* to extension pack */
+/*(27) not connected */
+#define H5000_GPIO_I2S_BITCLK   (28)       /* connected to AC97 codec */
+#define H5000_GPIO_I2S_DATAOUT  (29)       /* connected to AC97 codec */
+#define H5000_GPIO_I2S_DATAIN   (30)       /* connected to AC97 codec */
+#define H5000_GPIO_I2S_LRCLK    (31)       /* connected to AC97 codec */
+#define H5000_GPIO_I2S_SYSCLK   (32)       /* connected to AC97 codec */
+/*(33) is CS5# */
+#define H5000_GPIO_COM_RXD      (34)       /* connected to cradle/cable connector */
+#define H5000_GPIO_COM_CTS      (35)       /* connected to cradle/cable connector */
+#define H5000_GPIO_COM_DCD      (36)       /* connected to cradle/cable connector */
+#define H5000_GPIO_COM_DSR      (37)       /* connected to cradle/cable connector */
+#define H5000_GPIO_COM_RI       (38)       /* connected to cradle/cable connector */
+#define H5000_GPIO_COM_TXD      (39)       /* connected to cradle/cable connector */
+#define H5000_GPIO_COM_DTR      (40)       /* connected to cradle/cable connector */
+#define H5000_GPIO_COM_RTS      (41)       /* connected to cradle/cable connector */
+
+#define H5000_GPIO_BT_RXD       (42)       /* connected to BT (LMX9814) */
+#define H5000_GPIO_BT_TXD       (43)       /* connected to BT (LMX9814) */
+#define H5000_GPIO_BT_CTS       (44)       /* connected to BT (LMX9814) */
+#define H5000_GPIO_BT_RTS       (45)       /* connected to BT (LMX9814) */
+
+#define H5000_GPIO_IRDA_RXD     (46)
+#define H5000_GPIO_IRDA_TXD     (47)
+
+#define H5000_GPIO_POE_N        (48)       /* used for pcmcia */
+#define H5000_GPIO_PWE_N        (49)       /* used for pcmcia */
+#define H5000_GPIO_PIOR_N       (50)       /* used for pcmcia */
+#define H5000_GPIO_PIOW_N       (51)       /* used for pcmcia */
+#define H5000_GPIO_PCE1_N       (52)       /* used for pcmcia */
+#define H5000_GPIO_PCE2_N       (53)       /* used for pcmcia */
+#define H5000_GPIO_PSKTSEL      (54)       /* used for pcmcia */
+#define H5000_GPIO_PREG_N       (55)       /* used for pcmcia */
+#define H5000_GPIO_PWAIT_N      (56)       /* used for pcmcia */
+#define H5000_GPIO_IOIS16_N     (57)       /* used for pcmcia */
+
+#define H5000_GPIO_IRDA_SD      (58)       /* to hsdl3002 sd */
+/*(59) not connected */
+#define H5000_GPIO_POWER_SD_N   (60)       /* controls power to SD */
+#define H5000_GPIO_POWER_RS232_N	(61)       /* inverted FORCEON to rs232 transceiver */
+#define H5000_GPIO_POWER_ACCEL_N	(62)       /* controls power to accel */
+/*(63) is not connected */
+#define H5000_GPIO_OPT_NVRAM    (64)       /* controls power to expansion pack */
+#define H5000_GPIO_CHG_EN       (65)       /* to sc801 en */
+#define H5000_GPIO_USB_PULLUP   (66)       /* USB d+ pullup via 1.5K resistor */
+#define H5000_GPIO_BT_2V8_N     (67)       /* 2.8V used by bluetooth */
+#define H5000_GPIO_EXT_CHG_RATE (68)       /* enables external charging rate */
+/*(69) is not connected */
+#define H5000_GPIO_CIR_RESET    (70)       /* consumer IR reset */
+#define H5000_GPIO_POWER_LIGHT_SENSOR_N	(71)
+#define H5000_GPIO_BT_M_RESET   (72)
+#define H5000_GPIO_STD_CHG_RATE (73)
+#define H5000_GPIO_SD_WP_N      (74)
+#define H5000_GPIO_MOTOR_ON_N   (75)       /* external pullup on this */
+#define H5000_GPIO_HEADPHONE_DETECT	(76)
+#define H5000_GPIO_USB_CHG_RATE (77)       /* select rate for charging via usb */
+/*(78) is CS2# */
+/*(79) is CS3# */
+/*(80) is CS4# */
+
+#endif /* __ASM_ARCH_H5000_H */

arch/arm/mach-pxa/include/mach/hardware.h

@@ -102,6 +102,9 @@
  *  PXA930	B0	0x69056835	0x5E643013
  *  PXA930	B1	0x69056837	0x7E643013
  *  PXA930	B2	0x69056838	0x8E643013
+ *
+ *  PXA935	A0	0x56056931	0x1E653013
+ *  PXA935	B0	0x56056936	0x6E653013
  */
 #ifdef CONFIG_PXA25x
 #define __cpu_is_pxa210(id)				\
@@ -178,12 +181,22 @@
 #define __cpu_is_pxa930(id)				\
 	({						\
 		unsigned int _id = (id) >> 4 & 0xfff;	\
-		_id == 0x683;		\
+		_id == 0x683;				\
 	 })
 #else
 #define __cpu_is_pxa930(id)	(0)
 #endif
 
+#ifdef CONFIG_CPU_PXA935
+#define __cpu_is_pxa935(id)				\
+	({						\
+		unsigned int _id = (id) >> 4 & 0xfff;	\
+		_id == 0x693;				\
+	 })
+#else
+#define __cpu_is_pxa935(id)	(0)
+#endif
+
 #define cpu_is_pxa210()					\
 	({						\
 		__cpu_is_pxa210(read_cpuid_id());	\
@@ -204,8 +217,6 @@
 		__cpu_is_pxa25x(read_cpuid_id());	\
 	})
 
-extern int cpu_is_pxa26x(void);
-
 #define cpu_is_pxa27x()					\
 	({						\
 		__cpu_is_pxa27x(read_cpuid_id());	\
@@ -232,6 +243,12 @@ extern int cpu_is_pxa26x(void);
 		__cpu_is_pxa930(id);			\
 	 })
 
+#define cpu_is_pxa935()					\
+	({						\
+		unsigned int id = read_cpuid(CPUID_ID);	\
+		__cpu_is_pxa935(id);			\
+	 })
+
 /*
  * CPUID Core Generation Bit
  * <= 0x2 for pxa21x/pxa25x/pxa26x/pxa27x
@@ -249,6 +266,12 @@ extern int cpu_is_pxa26x(void);
 		_id == 0x3;				\
 	 })
 
+#define __cpu_is_pxa9xx(id)				\
+	({						\
+		unsigned int _id = (id) >> 4 & 0xfff;	\
+		_id == 0x683 || _id == 0x693;		\
+	 })
+
 #define cpu_is_pxa2xx()					\
 	({						\
 		__cpu_is_pxa2xx(read_cpuid_id());	\
@@ -259,21 +282,10 @@ extern int cpu_is_pxa26x(void);
 		__cpu_is_pxa3xx(read_cpuid_id());	\
 	 })
 
-/*
- * Handy routine to set GPIO alternate functions
- */
-extern int pxa_gpio_mode( int gpio_mode );
-
-/*
- * Return GPIO level, nonzero means high, zero is low
- */
-extern int pxa_gpio_get_value(unsigned gpio);
-
-/*
- * Set output GPIO level
- */
-extern void pxa_gpio_set_value(unsigned gpio, int value);
-
+#define cpu_is_pxa9xx()					\
+	({						\
+		__cpu_is_pxa9xx(read_cpuid_id());	\
+	 })
 /*
  * return current memory and LCD clock frequency in units of 10kHz
  */

arch/arm/mach-pxa/include/mach/mfp-pxa25x.h

@@ -158,4 +158,35 @@
 #define GPIO76_LCD_PCLK		MFP_CFG_OUT(GPIO76, AF2, DRIVE_LOW)
 #define GPIO77_LCD_BIAS		MFP_CFG_OUT(GPIO77, AF2, DRIVE_LOW)
 
+#ifdef CONFIG_CPU_PXA26x
+/* GPIO */
+#define GPIO85_GPIO		MFP_CFG_IN(GPIO85, AF0)
+#define GPIO86_GPIO		MFP_CFG_IN(GPIO86, AF1)
+#define GPIO87_GPIO		MFP_CFG_IN(GPIO87, AF1)
+#define GPIO88_GPIO		MFP_CFG_IN(GPIO88, AF1)
+#define GPIO89_GPIO		MFP_CFG_IN(GPIO89, AF1)
+
+/* SDRAM */
+#define GPIO86_nSDCS2		MFP_CFG_OUT(GPIO86, AF0, DRIVE_HIGH)
+#define GPIO87_nSDCS3		MFP_CFG_OUT(GPIO87, AF0, DRIVE_HIGH)
+#define GPIO88_RDnWR		MFP_CFG_OUT(GPIO88, AF0, DRIVE_HIGH)
+#define GPIO89_nACRESET		MFP_CFG_OUT(GPIO89, AF0, DRIVE_HIGH)
+
+/* USB */
+#define GPIO9_USB_RCV		MFP_CFG_IN(GPIO9, AF1)
+#define GPIO32_USB_VP		MFP_CFG_IN(GPIO32, AF2)
+#define GPIO34_USB_VM		MFP_CFG_IN(GPIO34, AF2)
+#define GPIO39_USB_VPO		MFP_CFG_OUT(GPIO39, AF3, DRIVE_LOW)
+#define GPIO56_USB_VMO		MFP_CFG_OUT(GPIO56, AF1, DRIVE_LOW)
+#define GPIO57_USB_nOE		MFP_CFG_OUT(GPIO57, AF1, DRIVE_HIGH)
+
+/* ASSP */
+#define GPIO28_ASSP_BITCLK_IN	MFP_CFG_IN(GPIO28, AF3)
+#define GPIO28_ASSP_BITCLK_OUT	MFP_CFG_OUT(GPIO28, AF3, DRIVE_LOW)
+#define GPIO29_ASSP_RXD		MFP_CFG_IN(GPIO29, AF3)
+#define GPIO30_ASSP_TXD		MFP_CFG_OUT(GPIO30, AF3, DRIVE_LOW)
+#define GPIO31_ASSP_SFRM_IN	MFP_CFG_IN(GPIO31, AF1)
+#define GPIO31_ASSP_SFRM_OUT	MFP_CFG_OUT(GPIO31, AF3, DRIVE_LOW)
+#endif
+
 #endif /* __ASM_ARCH_MFP_PXA25X_H */

arch/arm/mach-pxa/include/mach/mfp-pxa27x.h

@@ -11,6 +11,12 @@
 #include <mach/mfp.h>
 #include <mach/mfp-pxa2xx.h>
 
+/* Note: GPIO3/GPIO4 will be driven by Power I2C when PCFR/PI2C_EN
+ * bit is set, regardless of the GPIO configuration
+ */
+#define GPIO3_GPIO		MFP_CFG_IN(GPIO3, AF0)
+#define GPIO4_GPIO		MFP_CFG_IN(GPIO4, AF0)
+
 /* GPIO */
 #define GPIO85_GPIO		MFP_CFG_IN(GPIO85, AF0)
 #define GPIO86_GPIO		MFP_CFG_IN(GPIO86, AF0)

arch/arm/mach-pxa/include/mach/mioa701.h

@@ -10,12 +10,14 @@
 	 (MFP_PIN(pin) | MFP_##af | MFP_DIR_OUT | MFP_LPM_##state))
 
 /* Global GPIOs */
-#define GPIO9_CHARGE_nEN			9
+#define GPIO9_CHARGE_EN				9
 #define GPIO18_POWEROFF				18
 #define GPIO87_LCD_POWER			87
+#define GPIO96_AC_DETECT			96
+#define GPIO80_MAYBE_CHARGE_VDROP		80	/* Drop of 88mV */
 
 /* USB */
-#define GPIO13_USB_DETECT			13
+#define GPIO13_nUSB_DETECT			13
 #define GPIO22_USB_ENABLE			22
 
 /* SDIO bits */
@@ -24,7 +26,10 @@
 #define GPIO91_SDIO_EN				91
 
 /* Bluetooth */
+#define GPIO14_BT_nACTIVITY			14
 #define GPIO83_BT_ON				83
+#define GPIO77_BT_UNKNOWN1			77
+#define GPIO86_BT_MAYBE_nRESET			86
 
 /* GPS */
 #define GPIO23_GPS_UNKNOWN1			23

arch/arm/mach-pxa/include/mach/pxa2xx-gpio.h

@@ -365,4 +365,9 @@
 #define GPIO117_I2CSCL_MD	(117 | GPIO_ALT_FN_1_IN)
 #define GPIO118_I2CSDA_MD	(118 | GPIO_ALT_FN_1_IN)
 
+/*
+ * Handy routine to set GPIO alternate functions
+ */
+extern int pxa_gpio_mode( int gpio_mode );
+
 #endif /* __ASM_ARCH_PXA2XX_GPIO_H */

arch/arm/mach-pxa/include/mach/pxa2xx-regs.h

@@ -49,6 +49,11 @@
 #define MECR_NOS	(1 << 0)	/* Number Of Sockets: 0 -> 1 sock, 1 -> 2 sock */
 #define MECR_CIT	(1 << 1)	/* Card Is There: 0 -> no card, 1 -> card inserted */
 
+#define MDCNFG_DE0	(1 << 0)	/* SDRAM Bank 0 Enable */
+#define MDCNFG_DE1	(1 << 1)	/* SDRAM Bank 1 Enable */
+#define MDCNFG_DE2	(1 << 16)	/* SDRAM Bank 2 Enable */
+#define MDCNFG_DE3	(1 << 17)	/* SDRAM Bank 3 Enable */
+
 #define MDREFR_K0DB4	(1 << 29)	/* SDCLK0 Divide by 4 Control/Status */
 #define MDREFR_K2FREE	(1 << 25)	/* SDRAM Free-Running Control */
 #define MDREFR_K1FREE	(1 << 24)	/* SDRAM Free-Running Control */
@@ -243,4 +248,11 @@
 #define OSCC_OON	(1 << 1)	/* 32.768kHz OON (write-once only bit) */
 #define OSCC_OOK	(1 << 0)	/* 32.768kHz OOK (read-only bit) */
 
+/* PWRMODE register M field values */
+
+#define PWRMODE_IDLE		0x1
+#define PWRMODE_STANDBY		0x2
+#define PWRMODE_SLEEP		0x3
+#define PWRMODE_DEEPSLEEP	0x7
+
 #endif

arch/arm/mach-pxa/include/mach/regs-ac97.h

+#ifndef __ASM_ARCH_REGS_AC97_H
+#define __ASM_ARCH_REGS_AC97_H
+
+/*
+ * AC97 Controller registers
+ */
+
+#define POCR		__REG(0x40500000)  /* PCM Out Control Register */
+#define POCR_FEIE	(1 << 3)	/* FIFO Error Interrupt Enable */
+#define POCR_FSRIE	(1 << 1)	/* FIFO Service Request Interrupt Enable */
+
+#define PICR		__REG(0x40500004)  /* PCM In Control Register */
+#define PICR_FEIE	(1 << 3)	/* FIFO Error Interrupt Enable */
+#define PICR_FSRIE	(1 << 1)	/* FIFO Service Request Interrupt Enable */
+
+#define MCCR		__REG(0x40500008)  /* Mic In Control Register */
+#define MCCR_FEIE	(1 << 3)	/* FIFO Error Interrupt Enable */
+#define MCCR_FSRIE	(1 << 1)	/* FIFO Service Request Interrupt Enable */
+
+#define GCR		__REG(0x4050000C)  /* Global Control Register */
+#ifdef CONFIG_PXA3xx
+#define GCR_CLKBPB	(1 << 31)	/* Internal clock enable */
+#endif
+#define GCR_nDMAEN	(1 << 24)	/* non DMA Enable */
+#define GCR_CDONE_IE	(1 << 19)	/* Command Done Interrupt Enable */
+#define GCR_SDONE_IE	(1 << 18)	/* Status Done Interrupt Enable */
+#define GCR_SECRDY_IEN	(1 << 9)	/* Secondary Ready Interrupt Enable */
+#define GCR_PRIRDY_IEN	(1 << 8)	/* Primary Ready Interrupt Enable */
+#define GCR_SECRES_IEN	(1 << 5)	/* Secondary Resume Interrupt Enable */
+#define GCR_PRIRES_IEN	(1 << 4)	/* Primary Resume Interrupt Enable */
+#define GCR_ACLINK_OFF	(1 << 3)	/* AC-link Shut Off */
+#define GCR_WARM_RST	(1 << 2)	/* AC97 Warm Reset */
+#define GCR_COLD_RST	(1 << 1)	/* AC'97 Cold Reset (0 = active) */
+#define GCR_GIE		(1 << 0)	/* Codec GPI Interrupt Enable */
+
+#define POSR		__REG(0x40500010)  /* PCM Out Status Register */
+#define POSR_FIFOE	(1 << 4)	/* FIFO error */
+#define POSR_FSR	(1 << 2)	/* FIFO Service Request */
+
+#define PISR		__REG(0x40500014)  /* PCM In Status Register */
+#define PISR_FIFOE	(1 << 4)	/* FIFO error */
+#define PISR_EOC	(1 << 3)	/* DMA End-of-Chain (exclusive clear) */
+#define PISR_FSR	(1 << 2)	/* FIFO Service Request */
+
+#define MCSR		__REG(0x40500018)  /* Mic In Status Register */
+#define MCSR_FIFOE	(1 << 4)	/* FIFO error */
+#define MCSR_EOC	(1 << 3)	/* DMA End-of-Chain (exclusive clear) */
+#define MCSR_FSR	(1 << 2)	/* FIFO Service Request */
+
+#define GSR		__REG(0x4050001C)  /* Global Status Register */
+#define GSR_CDONE	(1 << 19)	/* Command Done */
+#define GSR_SDONE	(1 << 18)	/* Status Done */
+#define GSR_RDCS	(1 << 15)	/* Read Completion Status */
+#define GSR_BIT3SLT12	(1 << 14)	/* Bit 3 of slot 12 */
+#define GSR_BIT2SLT12	(1 << 13)	/* Bit 2 of slot 12 */
+#define GSR_BIT1SLT12	(1 << 12)	/* Bit 1 of slot 12 */
+#define GSR_SECRES	(1 << 11)	/* Secondary Resume Interrupt */
+#define GSR_PRIRES	(1 << 10)	/* Primary Resume Interrupt */
+#define GSR_SCR		(1 << 9)	/* Secondary Codec Ready */
+#define GSR_PCR		(1 << 8)	/*  Primary Codec Ready */
+#define GSR_MCINT	(1 << 7)	/* Mic In Interrupt */
+#define GSR_POINT	(1 << 6)	/* PCM Out Interrupt */
+#define GSR_PIINT	(1 << 5)	/* PCM In Interrupt */
+#define GSR_ACOFFD	(1 << 3)	/* AC-link Shut Off Done */
+#define GSR_MOINT	(1 << 2)	/* Modem Out Interrupt */
+#define GSR_MIINT	(1 << 1)	/* Modem In Interrupt */
+#define GSR_GSCI	(1 << 0)	/* Codec GPI Status Change Interrupt */
+
+#define CAR		__REG(0x40500020)  /* CODEC Access Register */
+#define CAR_CAIP	(1 << 0)	/* Codec Access In Progress */
+
+#define PCDR		__REG(0x40500040)  /* PCM FIFO Data Register */
+#define MCDR		__REG(0x40500060)  /* Mic-in FIFO Data Register */
+
+#define MOCR		__REG(0x40500100)  /* Modem Out Control Register */
+#define MOCR_FEIE	(1 << 3)	/* FIFO Error */
+#define MOCR_FSRIE	(1 << 1)	/* FIFO Service Request Interrupt Enable */
+
+#define MICR		__REG(0x40500108)  /* Modem In Control Register */
+#define MICR_FEIE	(1 << 3)	/* FIFO Error */
+#define MICR_FSRIE	(1 << 1)	/* FIFO Service Request Interrupt Enable */
+
+#define MOSR		__REG(0x40500110)  /* Modem Out Status Register */
+#define MOSR_FIFOE	(1 << 4)	/* FIFO error */
+#define MOSR_FSR	(1 << 2)	/* FIFO Service Request */
+
+#define MISR		__REG(0x40500118)  /* Modem In Status Register */
+#define MISR_FIFOE	(1 << 4)	/* FIFO error */
+#define MISR_EOC	(1 << 3)	/* DMA End-of-Chain (exclusive clear) */
+#define MISR_FSR	(1 << 2)	/* FIFO Service Request */
+
+#define MODR		__REG(0x40500140)  /* Modem FIFO Data Register */
+
+#define PAC_REG_BASE	__REG(0x40500200)  /* Primary Audio Codec */
+#define SAC_REG_BASE	__REG(0x40500300)  /* Secondary Audio Codec */
+#define PMC_REG_BASE	__REG(0x40500400)  /* Primary Modem Codec */
+#define SMC_REG_BASE	__REG(0x40500500)  /* Secondary Modem Codec */
+
+#endif /* __ASM_ARCH_REGS_AC97_H */

arch/arm/mach-pxa/include/mach/regs-uart.h

+#ifndef __ASM_ARCH_REGS_UART_H
+#define __ASM_ARCH_REGS_UART_H
+
+/*
+ * UARTs
+ */
+
+/* Full Function UART (FFUART) */
+#define FFUART		FFRBR
+#define FFRBR		__REG(0x40100000)  /* Receive Buffer Register (read only) */
+#define FFTHR		__REG(0x40100000)  /* Transmit Holding Register (write only) */
+#define FFIER		__REG(0x40100004)  /* Interrupt Enable Register (read/write) */
+#define FFIIR		__REG(0x40100008)  /* Interrupt ID Register (read only) */
+#define FFFCR		__REG(0x40100008)  /* FIFO Control Register (write only) */
+#define FFLCR		__REG(0x4010000C)  /* Line Control Register (read/write) */
+#define FFMCR		__REG(0x40100010)  /* Modem Control Register (read/write) */
+#define FFLSR		__REG(0x40100014)  /* Line Status Register (read only) */
+#define FFMSR		__REG(0x40100018)  /* Modem Status Register (read only) */
+#define FFSPR		__REG(0x4010001C)  /* Scratch Pad Register (read/write) */
+#define FFISR		__REG(0x40100020)  /* Infrared Selection Register (read/write) */
+#define FFDLL		__REG(0x40100000)  /* Divisor Latch Low Register (DLAB = 1) (read/write) */
+#define FFDLH		__REG(0x40100004)  /* Divisor Latch High Register (DLAB = 1) (read/write) */
+
+/* Bluetooth UART (BTUART) */
+#define BTUART		BTRBR
+#define BTRBR		__REG(0x40200000)  /* Receive Buffer Register (read only) */
+#define BTTHR		__REG(0x40200000)  /* Transmit Holding Register (write only) */
+#define BTIER		__REG(0x40200004)  /* Interrupt Enable Register (read/write) */
+#define BTIIR		__REG(0x40200008)  /* Interrupt ID Register (read only) */
+#define BTFCR		__REG(0x40200008)  /* FIFO Control Register (write only) */
+#define BTLCR		__REG(0x4020000C)  /* Line Control Register (read/write) */
+#define BTMCR		__REG(0x40200010)  /* Modem Control Register (read/write) */
+#define BTLSR		__REG(0x40200014)  /* Line Status Register (read only) */
+#define BTMSR		__REG(0x40200018)  /* Modem Status Register (read only) */
+#define BTSPR		__REG(0x4020001C)  /* Scratch Pad Register (read/write) */
+#define BTISR		__REG(0x40200020)  /* Infrared Selection Register (read/write) */
+#define BTDLL		__REG(0x40200000)  /* Divisor Latch Low Register (DLAB = 1) (read/write) */
+#define BTDLH		__REG(0x40200004)  /* Divisor Latch High Register (DLAB = 1) (read/write) */
+
+/* Standard UART (STUART) */
+#define STUART		STRBR
+#define STRBR		__REG(0x40700000)  /* Receive Buffer Register (read only) */
+#define STTHR		__REG(0x40700000)  /* Transmit Holding Register (write only) */
+#define STIER		__REG(0x40700004)  /* Interrupt Enable Register (read/write) */
+#define STIIR		__REG(0x40700008)  /* Interrupt ID Register (read only) */
+#define STFCR		__REG(0x40700008)  /* FIFO Control Register (write only) */
+#define STLCR		__REG(0x4070000C)  /* Line Control Register (read/write) */
+#define STMCR		__REG(0x40700010)  /* Modem Control Register (read/write) */
+#define STLSR		__REG(0x40700014)  /* Line Status Register (read only) */
+#define STMSR		__REG(0x40700018)  /* Reserved */
+#define STSPR		__REG(0x4070001C)  /* Scratch Pad Register (read/write) */
+#define STISR		__REG(0x40700020)  /* Infrared Selection Register (read/write) */
+#define STDLL		__REG(0x40700000)  /* Divisor Latch Low Register (DLAB = 1) (read/write) */
+#define STDLH		__REG(0x40700004)  /* Divisor Latch High Register (DLAB = 1) (read/write) */
+
+/* Hardware UART (HWUART) */
+#define HWUART		HWRBR
+#define HWRBR		__REG(0x41600000)  /* Receive Buffer Register (read only) */
+#define HWTHR		__REG(0x41600000)  /* Transmit Holding Register (write only) */
+#define HWIER		__REG(0x41600004)  /* Interrupt Enable Register (read/write) */
+#define HWIIR		__REG(0x41600008)  /* Interrupt ID Register (read only) */
+#define HWFCR		__REG(0x41600008)  /* FIFO Control Register (write only) */
+#define HWLCR		__REG(0x4160000C)  /* Line Control Register (read/write) */
+#define HWMCR		__REG(0x41600010)  /* Modem Control Register (read/write) */
+#define HWLSR		__REG(0x41600014)  /* Line Status Register (read only) */
+#define HWMSR		__REG(0x41600018)  /* Modem Status Register (read only) */
+#define HWSPR		__REG(0x4160001C)  /* Scratch Pad Register (read/write) */
+#define HWISR		__REG(0x41600020)  /* Infrared Selection Register (read/write) */
+#define HWFOR		__REG(0x41600024)  /* Receive FIFO Occupancy Register (read only) */
+#define HWABR		__REG(0x41600028)  /* Auto-Baud Control Register (read/write) */
+#define HWACR		__REG(0x4160002C)  /* Auto-Baud Count Register (read only) */
+#define HWDLL		__REG(0x41600000)  /* Divisor Latch Low Register (DLAB = 1) (read/write) */
+#define HWDLH		__REG(0x41600004)  /* Divisor Latch High Register (DLAB = 1) (read/write) */
+
+#define IER_DMAE	(1 << 7)	/* DMA Requests Enable */
+#define IER_UUE		(1 << 6)	/* UART Unit Enable */
+#define IER_NRZE	(1 << 5)	/* NRZ coding Enable */
+#define IER_RTIOE	(1 << 4)	/* Receiver Time Out Interrupt Enable */
+#define IER_MIE		(1 << 3)	/* Modem Interrupt Enable */
+#define IER_RLSE	(1 << 2)	/* Receiver Line Status Interrupt Enable */
+#define IER_TIE		(1 << 1)	/* Transmit Data request Interrupt Enable */
+#define IER_RAVIE	(1 << 0)	/* Receiver Data Available Interrupt Enable */
+
+#define IIR_FIFOES1	(1 << 7)	/* FIFO Mode Enable Status */
+#define IIR_FIFOES0	(1 << 6)	/* FIFO Mode Enable Status */
+#define IIR_TOD		(1 << 3)	/* Time Out Detected */
+#define IIR_IID2	(1 << 2)	/* Interrupt Source Encoded */
+#define IIR_IID1	(1 << 1)	/* Interrupt Source Encoded */
+#define IIR_IP		(1 << 0)	/* Interrupt Pending (active low) */
+
+#define FCR_ITL2	(1 << 7)	/* Interrupt Trigger Level */
+#define FCR_ITL1	(1 << 6)	/* Interrupt Trigger Level */
+#define FCR_RESETTF	(1 << 2)	/* Reset Transmitter FIFO */
+#define FCR_RESETRF	(1 << 1)	/* Reset Receiver FIFO */
+#define FCR_TRFIFOE	(1 << 0)	/* Transmit and Receive FIFO Enable */
+#define FCR_ITL_1	(0)
+#define FCR_ITL_8	(FCR_ITL1)
+#define FCR_ITL_16	(FCR_ITL2)
+#define FCR_ITL_32	(FCR_ITL2|FCR_ITL1)
+
+#define LCR_DLAB	(1 << 7)	/* Divisor Latch Access Bit */
+#define LCR_SB		(1 << 6)	/* Set Break */
+#define LCR_STKYP	(1 << 5)	/* Sticky Parity */
+#define LCR_EPS		(1 << 4)	/* Even Parity Select */
+#define LCR_PEN		(1 << 3)	/* Parity Enable */
+#define LCR_STB		(1 << 2)	/* Stop Bit */
+#define LCR_WLS1	(1 << 1)	/* Word Length Select */
+#define LCR_WLS0	(1 << 0)	/* Word Length Select */
+
+#define LSR_FIFOE	(1 << 7)	/* FIFO Error Status */
+#define LSR_TEMT	(1 << 6)	/* Transmitter Empty */
+#define LSR_TDRQ	(1 << 5)	/* Transmit Data Request */
+#define LSR_BI		(1 << 4)	/* Break Interrupt */
+#define LSR_FE		(1 << 3)	/* Framing Error */
+#define LSR_PE		(1 << 2)	/* Parity Error */
+#define LSR_OE		(1 << 1)	/* Overrun Error */
+#define LSR_DR		(1 << 0)	/* Data Ready */
+
+#define MCR_LOOP	(1 << 4)
+#define MCR_OUT2	(1 << 3)	/* force MSR_DCD in loopback mode */
+#define MCR_OUT1	(1 << 2)	/* force MSR_RI in loopback mode */
+#define MCR_RTS		(1 << 1)	/* Request to Send */
+#define MCR_DTR		(1 << 0)	/* Data Terminal Ready */
+
+#define MSR_DCD		(1 << 7)	/* Data Carrier Detect */
+#define MSR_RI		(1 << 6)	/* Ring Indicator */
+#define MSR_DSR		(1 << 5)	/* Data Set Ready */
+#define MSR_CTS		(1 << 4)	/* Clear To Send */
+#define MSR_DDCD	(1 << 3)	/* Delta Data Carrier Detect */
+#define MSR_TERI	(1 << 2)	/* Trailing Edge Ring Indicator */
+#define MSR_DDSR	(1 << 1)	/* Delta Data Set Ready */
+#define MSR_DCTS	(1 << 0)	/* Delta Clear To Send */
+
+/*
+ * IrSR (Infrared Selection Register)
+ */
+#define STISR_RXPL      (1 << 4)        /* Receive Data Polarity */
+#define STISR_TXPL      (1 << 3)        /* Transmit Data Polarity */
+#define STISR_XMODE     (1 << 2)        /* Transmit Pulse Width Select */
+#define STISR_RCVEIR    (1 << 1)        /* Receiver SIR Enable */
+#define STISR_XMITIR    (1 << 0)        /* Transmitter SIR Enable */
+
+#endif /* __ASM_ARCH_REGS_UART_H */

arch/arm/mach-pxa/include/mach/uncompress.h

@@ -10,7 +10,7 @@
  */
 
 #include <linux/serial_reg.h>
-#include <mach/pxa-regs.h>
+#include <mach/regs-uart.h>
 #include <asm/mach-types.h>
 
 #define __REG(x)       ((volatile unsigned long *)x)

arch/arm/mach-pxa/littleton.c

@@ -20,6 +20,7 @@
 #include <linux/delay.h>
 #include <linux/platform_device.h>
 #include <linux/clk.h>
+#include <linux/gpio.h>
 #include <linux/spi/spi.h>
 #include <linux/smc91x.h>
 
@@ -36,7 +37,6 @@
 
 #include <mach/pxa-regs.h>
 #include <mach/mfp-pxa300.h>
-#include <mach/gpio.h>
 #include <mach/pxafb.h>
 #include <mach/ssp.h>
 #include <mach/pxa2xx_spi.h>

arch/arm/mach-pxa/magician.c

@@ -123,6 +123,10 @@ static unsigned long magician_pin_config[] __initdata = {
 	GPIO107_GPIO,	/* DS1WM_IRQ */
 	GPIO108_GPIO,	/* GSM_READY */
 	GPIO115_GPIO,	/* nPEN_IRQ */
+
+	/* I2C */
+	GPIO117_I2C_SCL,
+	GPIO118_I2C_SDA,
 };
 
 /*

arch/arm/mach-pxa/mainstone.c

@@ -128,6 +128,10 @@ static unsigned long mainstone_pin_config[] = {
 	GPIO108_KP_MKOUT_5,
 	GPIO96_KP_MKOUT_6,
 
+	/* I2C */
+	GPIO117_I2C_SCL,
+	GPIO118_I2C_SDA,
+
 	/* GPIO */
 	GPIO1_GPIO | WAKEUP_ON_EDGE_BOTH,
 };

arch/arm/mach-pxa/mfp-pxa2xx.c

@@ -38,12 +38,13 @@ struct gpio_desc {
 	unsigned	valid		: 1;
 	unsigned	can_wakeup	: 1;
 	unsigned	keypad_gpio	: 1;
+	unsigned	dir_inverted	: 1;
 	unsigned int	mask; /* bit mask in PWER or PKWR */
+	unsigned int	mux_mask; /* bit mask of muxed gpio bits, 0 if no mux */
 	unsigned long	config;
 };
 
 static struct gpio_desc gpio_desc[MFP_PIN_GPIO127 + 1];
-static int gpio_nr;
 
 static unsigned long gpdr_lpm[4];
 
@@ -54,7 +55,7 @@ static int __mfp_config_gpio(unsigned gpio, unsigned long c)
 	int uorl = !!(gpio & 0x10); /* GAFRx_U or GAFRx_L ? */
 	int shft = (gpio & 0xf) << 1;
 	int fn = MFP_AF(c);
-	int dir = c & MFP_DIR_OUT;
+	int is_out = (c & MFP_DIR_OUT) ? 1 : 0;
 
 	if (fn > 3)
 		return -EINVAL;
@@ -68,7 +69,7 @@ static int __mfp_config_gpio(unsigned gpio, unsigned long c)
 	else
 		GAFR_U(bank) = gafr;
 
-	if (dir == MFP_DIR_OUT)
+	if (is_out ^ gpio_desc[gpio].dir_inverted)
 		GPDR(gpio) |= mask;
 	else
 		GPDR(gpio) &= ~mask;
@@ -77,11 +78,11 @@ static int __mfp_config_gpio(unsigned gpio, unsigned long c)
 	switch (c & MFP_LPM_STATE_MASK) {
 	case MFP_LPM_DRIVE_HIGH:
 		PGSR(bank) |= mask;
-		dir = MFP_DIR_OUT;
+		is_out = 1;
 		break;
 	case MFP_LPM_DRIVE_LOW:
 		PGSR(bank) &= ~mask;
-		dir = MFP_DIR_OUT;
+		is_out = 1;
 		break;
 	case MFP_LPM_DEFAULT:
 		break;
@@ -92,7 +93,7 @@ static int __mfp_config_gpio(unsigned gpio, unsigned long c)
 		break;
 	}
 
-	if (dir == MFP_DIR_OUT)
+	if (is_out ^ gpio_desc[gpio].dir_inverted)
 		gpdr_lpm[bank] |= mask;
 	else
 		gpdr_lpm[bank] &= ~mask;
@@ -106,7 +107,7 @@ static int __mfp_config_gpio(unsigned gpio, unsigned long c)
 		return -EINVAL;
 	}
 
-	if ((c & MFP_LPM_CAN_WAKEUP) && (dir == MFP_DIR_OUT)) {
+	if ((c & MFP_LPM_CAN_WAKEUP) && is_out) {
 		pr_warning("%s: output GPIO%d unable to wakeup\n",
 				__func__, gpio);
 		return -EINVAL;
@@ -169,7 +170,7 @@ void pxa2xx_mfp_set_lpm(int mfp, unsigned long lpm)
 int gpio_set_wake(unsigned int gpio, unsigned int on)
 {
 	struct gpio_desc *d;
-	unsigned long c;
+	unsigned long c, mux_taken;
 
 	if (gpio > mfp_to_gpio(MFP_PIN_GPIO127))
 		return -EINVAL;
@@ -183,9 +184,13 @@ int gpio_set_wake(unsigned int gpio, unsigned int on)
 	if (d->keypad_gpio)
 		return -EINVAL;
 
+	mux_taken = (PWER & d->mux_mask) & (~d->mask);
+	if (on && mux_taken)
+		return -EBUSY;
+
 	if (d->can_wakeup && (c & MFP_LPM_CAN_WAKEUP)) {
 		if (on) {
-			PWER |= d->mask;
+			PWER = (PWER & ~d->mux_mask) | d->mask;
 
 			if (c & MFP_LPM_EDGE_RISE)
 				PRER |= d->mask;
@@ -210,7 +215,7 @@ static void __init pxa25x_mfp_init(void)
 {
 	int i;
 
-	for (i = 0; i <= 84; i++)
+	for (i = 0; i <= pxa_last_gpio; i++)
 		gpio_desc[i].valid = 1;
 
 	for (i = 0; i <= 15; i++) {
@@ -218,7 +223,11 @@ static void __init pxa25x_mfp_init(void)
 		gpio_desc[i].mask = GPIO_bit(i);
 	}
 
-	gpio_nr = 85;
+	/* PXA26x has additional 4 GPIOs (86/87/88/89) which has the
+	 * direction bit inverted in GPDR2. See PXA26x DM 4.1.1.
+	 */
+	for (i = 86; i <= pxa_last_gpio; i++)
+		gpio_desc[i].dir_inverted = 1;
 }
 #else
 static inline void pxa25x_mfp_init(void) {}
@@ -251,11 +260,27 @@ int keypad_set_wake(unsigned int on)
 	return 0;
 }
 
+#define PWER_WEMUX2_GPIO38	(1 << 16)
+#define PWER_WEMUX2_GPIO53	(2 << 16)
+#define PWER_WEMUX2_GPIO40	(3 << 16)
+#define PWER_WEMUX2_GPIO36	(4 << 16)
+#define PWER_WEMUX2_MASK	(7 << 16)
+#define PWER_WEMUX3_GPIO31	(1 << 19)
+#define PWER_WEMUX3_GPIO113	(2 << 19)
+#define PWER_WEMUX3_MASK	(3 << 19)
+
+#define INIT_GPIO_DESC_MUXED(mux, gpio)				\
+do {								\
+	gpio_desc[(gpio)].can_wakeup = 1;			\
+	gpio_desc[(gpio)].mask = PWER_ ## mux ## _GPIO ##gpio;	\
+	gpio_desc[(gpio)].mux_mask = PWER_ ## mux ## _MASK;	\
+} while (0)
+
 static void __init pxa27x_mfp_init(void)
 {
 	int i, gpio;
 
-	for (i = 0; i <= 120; i++) {
+	for (i = 0; i <= pxa_last_gpio; i++) {
 		/* skip GPIO2, 5, 6, 7, 8, they are not
 		 * valid pins allow configuration
 		 */
@@ -286,7 +311,12 @@ static void __init pxa27x_mfp_init(void)
 	gpio_desc[35].can_wakeup = 1;
 	gpio_desc[35].mask = PWER_WE35;
 
-	gpio_nr = 121;
+	INIT_GPIO_DESC_MUXED(WEMUX3, 31);
+	INIT_GPIO_DESC_MUXED(WEMUX3, 113);
+	INIT_GPIO_DESC_MUXED(WEMUX2, 38);
+	INIT_GPIO_DESC_MUXED(WEMUX2, 53);
+	INIT_GPIO_DESC_MUXED(WEMUX2, 40);
+	INIT_GPIO_DESC_MUXED(WEMUX2, 36);
 }
 #else
 static inline void pxa27x_mfp_init(void) {}
@@ -300,7 +330,7 @@ static int pxa2xx_mfp_suspend(struct sys_device *d, pm_message_t state)
 {
 	int i;
 
-	for (i = 0; i <= gpio_to_bank(gpio_nr); i++) {
+	for (i = 0; i <= gpio_to_bank(pxa_last_gpio); i++) {
 
 		saved_gafr[0][i] = GAFR_L(i);
 		saved_gafr[1][i] = GAFR_U(i);
@@ -315,7 +345,7 @@ static int pxa2xx_mfp_resume(struct sys_device *d)
 {
 	int i;
 
-	for (i = 0; i <= gpio_to_bank(gpio_nr); i++) {
+	for (i = 0; i <= gpio_to_bank(pxa_last_gpio); i++) {
 		GAFR_L(i) = saved_gafr[0][i];
 		GAFR_U(i) = saved_gafr[1][i];
 		GPDR(i * 32) = saved_gpdr[i];
@@ -348,7 +378,7 @@ static int __init pxa2xx_mfp_init(void)
 		pxa27x_mfp_init();
 
 	/* initialize gafr_run[], pgsr_lpm[] from existing values */
-	for (i = 0; i <= gpio_to_bank(gpio_nr); i++)
+	for (i = 0; i <= gpio_to_bank(pxa_last_gpio); i++)
 		gpdr_lpm[i] = GPDR(i * 32);
 
 	return sysdev_class_register(&pxa2xx_mfp_sysclass);

arch/arm/mach-pxa/mioa701.c

@@ -34,7 +34,7 @@
 #include <linux/irq.h>
 #include <linux/pda_power.h>
 #include <linux/power_supply.h>
-#include <linux/wm97xx.h>
+#include <linux/wm97xx_batt.h>
 #include <linux/mtd/physmap.h>
 
 #include <asm/mach-types.h>
@@ -46,6 +46,9 @@
 #include <mach/mmc.h>
 #include <mach/udc.h>
 #include <mach/pxa27x-udc.h>
+#include <mach/i2c.h>
+#include <mach/camera.h>
+#include <media/soc_camera.h>
 
 #include <mach/mioa701.h>
 
@@ -54,10 +57,11 @@
 
 static unsigned long mioa701_pin_config[] = {
 	/* Mio global */
-	MIO_CFG_OUT(GPIO9_CHARGE_nEN, AF0, DRIVE_LOW),
+	MIO_CFG_OUT(GPIO9_CHARGE_EN, AF0, DRIVE_LOW),
 	MIO_CFG_OUT(GPIO18_POWEROFF, AF0, DRIVE_LOW),
 	MFP_CFG_OUT(GPIO3, AF0, DRIVE_HIGH),
 	MFP_CFG_OUT(GPIO4, AF0, DRIVE_HIGH),
+	MIO_CFG_IN(GPIO80_MAYBE_CHARGE_VDROP, AF0),
 
 	/* Backlight PWM 0 */
 	GPIO16_PWM0_OUT,
@@ -74,7 +78,7 @@ static unsigned long mioa701_pin_config[] = {
 	MIO_CFG_OUT(GPIO91_SDIO_EN, AF0, DRIVE_LOW),
 
 	/* USB */
-	MIO_CFG_IN(GPIO13_USB_DETECT, AF0),
+	MIO_CFG_IN(GPIO13_nUSB_DETECT, AF0),
 	MIO_CFG_OUT(GPIO22_USB_ENABLE, AF0, DRIVE_LOW),
 
 	/* LCD */
@@ -98,12 +102,29 @@ static unsigned long mioa701_pin_config[] = {
 	GPIO75_LCD_LCLK,
 	GPIO76_LCD_PCLK,
 
+	/* QCI */
+	GPIO12_CIF_DD_7,
+	GPIO17_CIF_DD_6,
+	GPIO50_CIF_DD_3,
+	GPIO51_CIF_DD_2,
+	GPIO52_CIF_DD_4,
+	GPIO53_CIF_MCLK,
+	GPIO54_CIF_PCLK,
+	GPIO55_CIF_DD_1,
+	GPIO81_CIF_DD_0,
+	GPIO82_CIF_DD_5,
+	GPIO84_CIF_FV,
+	GPIO85_CIF_LV,
+
 	/* Bluetooth */
+	MIO_CFG_IN(GPIO14_BT_nACTIVITY, AF0),
 	GPIO44_BTUART_CTS,
 	GPIO42_BTUART_RXD,
 	GPIO45_BTUART_RTS,
 	GPIO43_BTUART_TXD,
 	MIO_CFG_OUT(GPIO83_BT_ON, AF0, DRIVE_LOW),
+	MIO_CFG_OUT(GPIO77_BT_UNKNOWN1, AF0, DRIVE_HIGH),
+	MIO_CFG_OUT(GPIO86_BT_MAYBE_nRESET, AF0, DRIVE_HIGH),
 
 	/* GPS */
 	MIO_CFG_OUT(GPIO23_GPS_UNKNOWN1, AF0, DRIVE_LOW),
@@ -151,16 +172,16 @@ static unsigned long mioa701_pin_config[] = {
 	GPIO104_KP_MKOUT_1,
 	GPIO105_KP_MKOUT_2,
 
+	/* I2C */
+	GPIO117_I2C_SCL,
+	GPIO118_I2C_SDA,
+
 	/* Unknown */
-	MFP_CFG_IN(GPIO14, AF0),
 	MFP_CFG_IN(GPIO20, AF0),
 	MFP_CFG_IN(GPIO21, AF0),
 	MFP_CFG_IN(GPIO33, AF0),
 	MFP_CFG_OUT(GPIO49, AF0, DRIVE_HIGH),
 	MFP_CFG_OUT(GPIO57, AF0, DRIVE_HIGH),
-	MFP_CFG_OUT(GPIO77, AF0, DRIVE_HIGH),
-	MFP_CFG_IN(GPIO80, AF0),
-	MFP_CFG_OUT(GPIO86, AF0, DRIVE_HIGH),
 	MFP_CFG_IN(GPIO96, AF0),
 	MFP_CFG_OUT(GPIO116, AF0, DRIVE_HIGH),
 };
@@ -407,7 +428,7 @@ static void udc_power_command(int cmd)
 
 static int is_usb_connected(void)
 {
-	return !!gpio_get_value(GPIO13_USB_DETECT);
+	return !gpio_get_value(GPIO13_nUSB_DETECT);
 }
 
 static struct pxa2xx_udc_mach_info mioa701_udc_info = {
@@ -659,13 +680,19 @@ static char *supplicants[] = {
 	"mioa701_battery"
 };
 
+static int is_ac_connected(void)
+{
+	return gpio_get_value(GPIO96_AC_DETECT);
+}
+
 static void mioa701_set_charge(int flags)
 {
-	gpio_set_value(GPIO9_CHARGE_nEN, !flags);
+	gpio_set_value(GPIO9_CHARGE_EN, (flags == PDA_POWER_CHARGE_USB));
 }
 
 static struct pda_power_pdata power_pdata = {
-	.is_ac_online	= is_usb_connected,
+	.is_ac_online	= is_ac_connected,
+	.is_usb_online	= is_usb_connected,
 	.set_charge = mioa701_set_charge,
 	.supplied_to = supplicants,
 	.num_supplicants = ARRAY_SIZE(supplicants),
@@ -674,8 +701,15 @@ static struct pda_power_pdata power_pdata = {
 static struct resource power_resources[] = {
 	[0] = {
 		.name	= "ac",
-		.start	= gpio_to_irq(GPIO13_USB_DETECT),
-		.end	= gpio_to_irq(GPIO13_USB_DETECT),
+		.start	= gpio_to_irq(GPIO96_AC_DETECT),
+		.end	= gpio_to_irq(GPIO96_AC_DETECT),
+		.flags	= IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE |
+		IORESOURCE_IRQ_LOWEDGE,
+	},
+	[1] = {
+		.name	= "usb",
+		.start	= gpio_to_irq(GPIO13_nUSB_DETECT),
+		.end	= gpio_to_irq(GPIO13_nUSB_DETECT),
 		.flags	= IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE |
 		IORESOURCE_IRQ_LOWEDGE,
 	},
@@ -691,120 +725,43 @@ static struct platform_device power_dev = {
 	},
 };
 
-#if defined(CONFIG_PDA_POWER) && defined(CONFIG_TOUCHSCREEN_WM97XX)
-static struct wm97xx *battery_wm;
-
-static enum power_supply_property battery_props[] = {
-	POWER_SUPPLY_PROP_STATUS,
-	POWER_SUPPLY_PROP_VOLTAGE_MAX_DESIGN,
-	POWER_SUPPLY_PROP_VOLTAGE_MIN_DESIGN,
-	POWER_SUPPLY_PROP_VOLTAGE_NOW,
-	POWER_SUPPLY_PROP_CHARGE_FULL_DESIGN,	/* Necessary for apm */
+static struct wm97xx_batt_info mioa701_battery_data = {
+	.batt_aux	= WM97XX_AUX_ID1,
+	.temp_aux	= -1,
+	.charge_gpio	= -1,
+	.min_voltage	= 0xc00,
+	.max_voltage	= 0xfc0,
+	.batt_tech	= POWER_SUPPLY_TECHNOLOGY_LION,
+	.batt_div	= 1,
+	.batt_mult	= 1,
+	.batt_name	= "mioa701_battery",
 };
 
-static int get_battery_voltage(void)
-{
-	int adc = -1;
-
-	if (battery_wm)
-		adc = wm97xx_read_aux_adc(battery_wm, WM97XX_AUX_ID1);
-	return adc;
-}
-
-static int get_battery_status(struct power_supply *b)
-{
-	int status;
-
-	if (is_usb_connected())
-		status = POWER_SUPPLY_STATUS_CHARGING;
-	else
-		status = POWER_SUPPLY_STATUS_DISCHARGING;
-
-	return status;
-}
-
-static int get_property(struct power_supply *b,
-			enum power_supply_property psp,
-			union power_supply_propval *val)
-{
-	int rc = 0;
-
-	switch (psp) {
-	case POWER_SUPPLY_PROP_STATUS:
-		val->intval = get_battery_status(b);
-		break;
-	case POWER_SUPPLY_PROP_VOLTAGE_MAX_DESIGN:
-		val->intval = 0xfd0;
-		break;
-	case POWER_SUPPLY_PROP_VOLTAGE_MIN_DESIGN:
-		val->intval = 0xc00;
-		break;
-	case POWER_SUPPLY_PROP_VOLTAGE_NOW:
-		val->intval = get_battery_voltage();
-		break;
-	case POWER_SUPPLY_PROP_CHARGE_FULL_DESIGN:
-		val->intval = 100;
-		break;
-	default:
-		val->intval = -1;
-		rc = -1;
-	}
-
-	return rc;
+/*
+ * Camera interface
+ */
+struct pxacamera_platform_data mioa701_pxacamera_platform_data = {
+	.flags  = PXA_CAMERA_MASTER | PXA_CAMERA_DATAWIDTH_8 |
+		PXA_CAMERA_PCLK_EN | PXA_CAMERA_MCLK_EN,
+	.mclk_10khz = 5000,
 };
 
-static struct power_supply battery_ps = {
-	.name = "mioa701_battery",
-	.type = POWER_SUPPLY_TYPE_BATTERY,
-	.get_property = get_property,
-	.properties = battery_props,
-	.num_properties = ARRAY_SIZE(battery_props),
+static struct soc_camera_link iclink = {
+	.bus_id	= 0, /* Must match id in pxa27x_device_camera in device.c */
 };
 
-static int battery_probe(struct platform_device *pdev)
-{
-	struct wm97xx *wm = platform_get_drvdata(pdev);
-	int rc;
-
-	battery_wm = wm;
-
-	rc = power_supply_register(NULL, &battery_ps);
-	if (rc)
-		dev_err(&pdev->dev,
-		"Could not register mioa701 battery -> %d\n", rc);
-	return rc;
-}
-
-static int battery_remove(struct platform_device *pdev)
-{
-	battery_wm = NULL;
-	return 0;
-}
-
-static struct platform_driver mioa701_battery_driver = {
-	.driver = {
-		.name = "wm97xx-battery",
+/* Board I2C devices. */
+static struct i2c_board_info __initdata mioa701_i2c_devices[] = {
+	{
+		/* Must initialize before the camera(s) */
+		I2C_BOARD_INFO("mt9m111", 0x5d),
+		.platform_data = &iclink,
 	},
-	.probe = battery_probe,
-	.remove = battery_remove
 };
 
-static int __init mioa701_battery_init(void)
-{
-	int rc;
-
-	rc = platform_driver_register(&mioa701_battery_driver);
-	if (rc)
-		printk(KERN_ERR "Could not register mioa701 battery driver\n");
-	return rc;
-}
-
-#else
-static int __init mioa701_battery_init(void)
-{
-	return 0;
-}
-#endif
+struct i2c_pxa_platform_data i2c_pdata = {
+	.fast_mode = 1,
+};
 
 /*
  * Mio global
@@ -851,17 +808,17 @@ static void mioa701_machine_exit(void);
 static void mioa701_poweroff(void)
 {
 	mioa701_machine_exit();
-	gpio_set_value(GPIO18_POWEROFF, 1);
+	arm_machine_restart('s');
 }
 
 static void mioa701_restart(char c)
 {
 	mioa701_machine_exit();
-	arm_machine_restart(c);
+	arm_machine_restart('s');
 }
 
 struct gpio_ress global_gpios[] = {
-	MIO_GPIO_OUT(GPIO9_CHARGE_nEN, 1, "Charger enable"),
+	MIO_GPIO_OUT(GPIO9_CHARGE_EN, 1, "Charger enable"),
 	MIO_GPIO_OUT(GPIO18_POWEROFF, 0, "Power Off"),
 	MIO_GPIO_OUT(GPIO87_LCD_POWER, 0, "LCD Power")
 };
@@ -879,12 +836,16 @@ static void __init mioa701_machine_init(void)
 	set_pxa_fb_info(&mioa701_pxafb_info);
 	pxa_set_mci_info(&mioa701_mci_info);
 	pxa_set_keypad_info(&mioa701_keypad_info);
+	wm97xx_bat_set_pdata(&mioa701_battery_data);
 	udc_init();
 	pm_power_off = mioa701_poweroff;
 	arm_pm_restart = mioa701_restart;
 	platform_add_devices(devices, ARRAY_SIZE(devices));
 	gsm_init();
-	mioa701_battery_init();
+
+	pxa_set_i2c_info(&i2c_pdata);
+	pxa_set_camera_info(&mioa701_pxacamera_platform_data);
+	i2c_register_board_info(0, ARRAY_AND_SIZE(mioa701_i2c_devices));
 }
 
 static void mioa701_machine_exit(void)

arch/arm/mach-pxa/pcm990-baseboard.c

@@ -55,6 +55,10 @@ static unsigned long pcm990_pin_config[] __initdata = {
 	GPIO89_USBH1_PEN,
 	/* PWM0 */
 	GPIO16_PWM0_OUT,
+
+	/* I2C */
+	GPIO117_I2C_SCL,
+	GPIO118_I2C_SDA,
 };
 
 /*

arch/arm/mach-pxa/poodle.c

@@ -20,6 +20,7 @@
 #include <linux/fb.h>
 #include <linux/pm.h>
 #include <linux/delay.h>
+#include <linux/mtd/physmap.h>
 #include <linux/gpio.h>
 #include <linux/spi/spi.h>
 #include <linux/spi/ads7846.h>
@@ -413,9 +414,40 @@ static struct pxafb_mach_info poodle_fb_info = {
 	.lcd_conn	= LCD_COLOR_TFT_16BPP,
 };
 
+static struct mtd_partition sharpsl_rom_parts[] = {
+	{
+		.name	="Boot PROM Filesystem",
+		.offset	= 0x00120000,
+		.size	= MTDPART_SIZ_FULL,
+	},
+};
+
+static struct physmap_flash_data sharpsl_rom_data = {
+	.width		= 2,
+	.nr_parts	= ARRAY_SIZE(sharpsl_rom_parts),
+	.parts		= sharpsl_rom_parts,
+};
+
+static struct resource sharpsl_rom_resources[] = {
+	{
+		.start	= 0x00000000,
+		.end	= 0x007fffff,
+		.flags	= IORESOURCE_MEM,
+	},
+};
+
+static struct platform_device sharpsl_rom_device = {
+	.name	= "physmap-flash",
+	.id	= -1,
+	.resource = sharpsl_rom_resources,
+	.num_resources = ARRAY_SIZE(sharpsl_rom_resources),
+	.dev.platform_data = &sharpsl_rom_data,
+};
+
 static struct platform_device *devices[] __initdata = {
 	&poodle_locomo_device,
 	&poodle_scoop_device,
+	&sharpsl_rom_device,
 };
 
 static void poodle_poweroff(void)

arch/arm/mach-pxa/pxa25x.c

@@ -36,12 +36,6 @@
 #include "devices.h"
 #include "clock.h"
 
-int cpu_is_pxa26x(void)
-{
-	return cpu_is_pxa250() && ((BOOT_DEF & 0x8) == 0);
-}
-EXPORT_SYMBOL_GPL(cpu_is_pxa26x);
-
 /*
  * Various clock factors driven by the CCCR register.
  */
@@ -319,13 +313,21 @@ void __init pxa25x_init_irq(void)
 	pxa_init_gpio(85, pxa25x_set_wake);
 }
 
+#ifdef CONFIG_CPU_PXA26x
+void __init pxa26x_init_irq(void)
+{
+	pxa_init_irq(32, pxa25x_set_wake);
+	pxa_init_gpio(90, pxa25x_set_wake);
+}
+#endif
+
 static struct platform_device *pxa25x_devices[] __initdata = {
 	&pxa25x_device_udc,
 	&pxa_device_ffuart,
 	&pxa_device_btuart,
 	&pxa_device_stuart,
 	&pxa_device_i2s,
-	&pxa_device_rtc,
+	&sa1100_device_rtc,
 	&pxa25x_device_ssp,
 	&pxa25x_device_nssp,
 	&pxa25x_device_assp,
@@ -371,7 +373,7 @@ static int __init pxa25x_init(void)
 	}
 
 	/* Only add HWUART for PXA255/26x; PXA210/250 do not have it. */
-	if (cpu_is_pxa255() || cpu_is_pxa26x()) {
+	if (cpu_is_pxa255()) {
 		clks_register(&pxa25x_hwuart_clkreg, 1);
 		ret = platform_device_register(&pxa_device_hwuart);
 	}

arch/arm/mach-pxa/pxa27x.c

@@ -332,38 +332,18 @@ static int pxa27x_set_wake(unsigned int irq, unsigned int on)
 void __init pxa27x_init_irq(void)
 {
 	pxa_init_irq(34, pxa27x_set_wake);
-	pxa_init_gpio(128, pxa27x_set_wake);
+	pxa_init_gpio(121, pxa27x_set_wake);
 }
 
 /*
  * device registration specific to PXA27x.
  */
-
-static struct resource i2c_power_resources[] = {
-	{
-		.start	= 0x40f00180,
-		.end	= 0x40f001a3,
-		.flags	= IORESOURCE_MEM,
-	}, {
-		.start	= IRQ_PWRI2C,
-		.end	= IRQ_PWRI2C,
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-struct platform_device pxa27x_device_i2c_power = {
-	.name		= "pxa2xx-i2c",
-	.id		= 1,
-	.resource	= i2c_power_resources,
-	.num_resources	= ARRAY_SIZE(i2c_power_resources),
-};
-
 void __init pxa27x_set_i2c_power_info(struct i2c_pxa_platform_data *info)
 {
 	local_irq_disable();
 	PCFR |= PCFR_PI2CEN;
 	local_irq_enable();
-	pxa27x_device_i2c_power.dev.platform_data = info;
+	pxa_register_device(&pxa27x_device_i2c_power, info);
 }
 
 static struct platform_device *devices[] __initdata = {
@@ -372,8 +352,8 @@ static struct platform_device *devices[] __initdata = {
 	&pxa_device_btuart,
 	&pxa_device_stuart,
 	&pxa_device_i2s,
+	&sa1100_device_rtc,
 	&pxa_device_rtc,
-	&pxa27x_device_i2c_power,
 	&pxa27x_device_ssp1,
 	&pxa27x_device_ssp2,
 	&pxa27x_device_ssp3,

arch/arm/mach-pxa/pxa3xx.c

@@ -29,6 +29,7 @@
 #include <mach/pm.h>
 #include <mach/dma.h>
 #include <mach/ssp.h>
+#include <mach/i2c.h>
 
 #include "generic.h"
 #include "devices.h"
@@ -544,28 +545,9 @@ void __init pxa3xx_init_irq(void)
  * device registration specific to PXA3xx.
  */
 
-static struct resource i2c_power_resources[] = {
-	{
-		.start  = 0x40f500c0,
-		.end    = 0x40f500d3,
-		.flags	= IORESOURCE_MEM,
-	}, {
-		.start	= IRQ_PWRI2C,
-		.end	= IRQ_PWRI2C,
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-struct platform_device pxa3xx_device_i2c_power = {
-	.name		= "pxa2xx-i2c",
-	.id		= 1,
-	.resource	= i2c_power_resources,
-	.num_resources	= ARRAY_SIZE(i2c_power_resources),
-};
-
 void __init pxa3xx_set_i2c_power_info(struct i2c_pxa_platform_data *info)
 {
-	pxa3xx_device_i2c_power.dev.platform_data = info;
+	pxa_register_device(&pxa3xx_device_i2c_power, info);
 }
 
 static struct platform_device *devices[] __initdata = {
@@ -574,6 +556,7 @@ static struct platform_device *devices[] __initdata = {
 	&pxa_device_btuart,
 	&pxa_device_stuart,
 	&pxa_device_i2s,
+	&sa1100_device_rtc,
 	&pxa_device_rtc,
 	&pxa27x_device_ssp1,
 	&pxa27x_device_ssp2,
@@ -581,7 +564,6 @@ static struct platform_device *devices[] __initdata = {
 	&pxa3xx_device_ssp4,
 	&pxa27x_device_pwm0,
 	&pxa27x_device_pwm1,
-	&pxa3xx_device_i2c_power,
 };
 
 static struct sys_device pxa3xx_sysdev[] = {

arch/arm/mach-pxa/spitz.c

@@ -22,6 +22,7 @@
 #include <linux/gpio.h>
 #include <linux/leds.h>
 #include <linux/mmc/host.h>
+#include <linux/mtd/physmap.h>
 #include <linux/pm.h>
 #include <linux/backlight.h>
 #include <linux/io.h>
@@ -122,6 +123,10 @@ static unsigned long spitz_pin_config[] __initdata = {
 	GPIO105_GPIO,	/* SPITZ_GPIO_CF_IRQ */
 	GPIO106_GPIO,	/* SPITZ_GPIO_CF2_IRQ */
 
+	/* I2C */
+	GPIO117_I2C_SCL,
+	GPIO118_I2C_SDA,
+
 	GPIO1_GPIO | WAKEUP_ON_EDGE_RISE,
 };
 
@@ -609,10 +614,41 @@ static struct pxafb_mach_info spitz_pxafb_info = {
 };
 
 
+static struct mtd_partition sharpsl_rom_parts[] = {
+	{
+		.name	="Boot PROM Filesystem",
+		.offset	= 0x00140000,
+		.size	= MTDPART_SIZ_FULL,
+	},
+};
+
+static struct physmap_flash_data sharpsl_rom_data = {
+	.width		= 2,
+	.nr_parts	= ARRAY_SIZE(sharpsl_rom_parts),
+	.parts		= sharpsl_rom_parts,
+};
+
+static struct resource sharpsl_rom_resources[] = {
+	{
+		.start	= 0x00000000,
+		.end	= 0x007fffff,
+		.flags	= IORESOURCE_MEM,
+	},
+};
+
+static struct platform_device sharpsl_rom_device = {
+	.name	= "physmap-flash",
+	.id	= -1,
+	.resource = sharpsl_rom_resources,
+	.num_resources = ARRAY_SIZE(sharpsl_rom_resources),
+	.dev.platform_data = &sharpsl_rom_data,
+};
+
 static struct platform_device *devices[] __initdata = {
 	&spitzscoop_device,
 	&spitzkbd_device,
 	&spitzled_device,
+	&sharpsl_rom_device,
 };
 
 static void spitz_poweroff(void)

arch/arm/mach-pxa/tosa.c

@@ -25,6 +25,7 @@
 #include <linux/mfd/tmio.h>
 #include <linux/mtd/nand.h>
 #include <linux/mtd/partitions.h>
+#include <linux/mtd/physmap.h>
 #include <linux/pm.h>
 #include <linux/gpio_keys.h>
 #include <linux/input.h>
@@ -733,6 +734,45 @@ static void tosa_tc6393xb_teardown(struct platform_device *dev)
 	gpio_free(TOSA_GPIO_CARD_VCC_ON);
 }
 
+#ifdef CONFIG_MFD_TC6393XB
+static struct fb_videomode tosa_tc6393xb_lcd_mode[] = {
+	{
+		.xres = 480,
+		.yres = 640,
+		.pixclock = 0x002cdf00,/* PLL divisor */
+		.left_margin = 0x004c,
+		.right_margin = 0x005b,
+		.upper_margin = 0x0001,
+		.lower_margin = 0x000d,
+		.hsync_len = 0x0002,
+		.vsync_len = 0x0001,
+		.sync = FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT,
+		.vmode = FB_VMODE_NONINTERLACED,
+	},{
+		.xres = 240,
+		.yres = 320,
+		.pixclock = 0x00e7f203,/* PLL divisor */
+		.left_margin = 0x0024,
+		.right_margin = 0x002f,
+		.upper_margin = 0x0001,
+		.lower_margin = 0x000d,
+		.hsync_len = 0x0002,
+		.vsync_len = 0x0001,
+		.sync = FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT,
+		.vmode = FB_VMODE_NONINTERLACED,
+	}
+};
+
+static struct tmio_fb_data tosa_tc6393xb_fb_config = {
+	.lcd_set_power	= tc6393xb_lcd_set_power,
+	.lcd_mode	= tc6393xb_lcd_mode,
+	.num_modes	= ARRAY_SIZE(tosa_tc6393xb_lcd_mode),
+	.modes		= &tosa_tc6393xb_lcd_mode[0],
+	.height		= 82,
+	.width		= 60,
+};
+#endif
+
 static struct tc6393xb_platform_data tosa_tc6393xb_data = {
 	.scr_pll2cr	= 0x0cc1,
 	.scr_gper	= 0x3300,
@@ -748,6 +788,9 @@ static struct tc6393xb_platform_data tosa_tc6393xb_data = {
 	.resume		= tosa_tc6393xb_resume,
 
 	.nand_data	= &tosa_tc6393xb_nand_config,
+#ifdef CONFIG_MFD_TC6393XB
+	.fb_data	= &tosa_tc6393xb_fb_config,
+#endif
 
 	.resume_restore = 1,
 };
@@ -789,6 +832,36 @@ static struct spi_board_info spi_board_info[] __initdata = {
 	},
 };
 
+static struct mtd_partition sharpsl_rom_parts[] = {
+	{
+		.name	="Boot PROM Filesystem",
+		.offset	= 0x00160000,
+		.size	= MTDPART_SIZ_FULL,
+	},
+};
+
+static struct physmap_flash_data sharpsl_rom_data = {
+	.width		= 2,
+	.nr_parts	= ARRAY_SIZE(sharpsl_rom_parts),
+	.parts		= sharpsl_rom_parts,
+};
+
+static struct resource sharpsl_rom_resources[] = {
+	{
+		.start	= 0x00000000,
+		.end	= 0x007fffff,
+		.flags	= IORESOURCE_MEM,
+	},
+};
+
+static struct platform_device sharpsl_rom_device = {
+	.name	= "physmap-flash",
+	.id	= -1,
+	.resource = sharpsl_rom_resources,
+	.num_resources = ARRAY_SIZE(sharpsl_rom_resources),
+	.dev.platform_data = &sharpsl_rom_data,
+};
+
 static struct platform_device *devices[] __initdata = {
 	&tosascoop_device,
 	&tosascoop_jc_device,
@@ -798,6 +871,7 @@ static struct platform_device *devices[] __initdata = {
 	&tosa_gpio_keys_device,
 	&tosaled_device,
 	&tosa_bt_device,
+	&sharpsl_rom_device,
 };
 
 static void tosa_poweroff(void)

arch/arm/mach-pxa/zylonite.c

@@ -18,6 +18,7 @@
 #include <linux/interrupt.h>
 #include <linux/init.h>
 #include <linux/platform_device.h>
+#include <linux/gpio.h>
 #include <linux/pwm_backlight.h>
 #include <linux/smc91x.h>
 
@@ -25,7 +26,6 @@
 #include <asm/mach/arch.h>
 #include <mach/hardware.h>
 #include <mach/audio.h>
-#include <mach/gpio.h>
 #include <mach/pxafb.h>
 #include <mach/zylonite.h>
 #include <mach/mmc.h>

arch/arm/mach-pxa/zylonite_pxa320.c

@@ -16,8 +16,8 @@
 #include <linux/module.h>
 #include <linux/kernel.h>
 #include <linux/init.h>
+#include <linux/gpio.h>
 
-#include <mach/gpio.h>
 #include <mach/mfp-pxa320.h>
 #include <mach/zylonite.h>
 

arch/arm/mm/proc-xsc3.S

@@ -481,3 +481,28 @@ __xsc3_proc_info:
 	.long	xsc3_mc_user_fns
 	.long	xsc3_cache_fns
 	.size	__xsc3_proc_info, . - __xsc3_proc_info
+
+/* Note: PXA935 changed its implementor ID from Intel to Marvell */
+
+	.type	__xsc3_pxa935_proc_info,#object
+__xsc3_pxa935_proc_info:
+	.long	0x56056000
+	.long	0xffffe000
+	.long	PMD_TYPE_SECT | \
+		PMD_SECT_BUFFERABLE | \
+		PMD_SECT_CACHEABLE | \
+		PMD_SECT_AP_WRITE | \
+		PMD_SECT_AP_READ
+	.long	PMD_TYPE_SECT | \
+		PMD_SECT_AP_WRITE | \
+		PMD_SECT_AP_READ
+	b	__xsc3_setup
+	.long	cpu_arch_name
+	.long	cpu_elf_name
+	.long	HWCAP_SWP|HWCAP_HALF|HWCAP_THUMB|HWCAP_FAST_MULT|HWCAP_EDSP
+	.long	cpu_xsc3_name
+	.long	xsc3_processor_functions
+	.long	v4wbi_tlb_fns
+	.long	xsc3_mc_user_fns
+	.long	xsc3_cache_fns
+	.size	__xsc3_pxa935_proc_info, . - __xsc3_pxa935_proc_info

drivers/input/touchscreen/mainstone-wm97xx.c

@@ -31,7 +31,7 @@
 #include <linux/interrupt.h>
 #include <linux/wm97xx.h>
 #include <linux/io.h>
-#include <mach/pxa-regs.h>
+#include <mach/regs-ac97.h>
 
 #define VERSION		"0.13"
 

drivers/media/video/pxa_camera.c

@@ -39,6 +39,8 @@
 #include <mach/pxa-regs.h>
 #include <mach/camera.h>
 
+#include "pxa_camera.h"
+
 #define PXA_CAM_VERSION_CODE KERNEL_VERSION(0, 0, 5)
 #define PXA_CAM_DRV_NAME "pxa27x-camera"
 

drivers/media/video/pxa_camera.h

+/* Camera Interface */
+#define CICR0		__REG(0x50000000)
+#define CICR1		__REG(0x50000004)
+#define CICR2		__REG(0x50000008)
+#define CICR3		__REG(0x5000000C)
+#define CICR4		__REG(0x50000010)
+#define CISR		__REG(0x50000014)
+#define CIFR		__REG(0x50000018)
+#define CITOR		__REG(0x5000001C)
+#define CIBR0		__REG(0x50000028)
+#define CIBR1		__REG(0x50000030)
+#define CIBR2		__REG(0x50000038)
+
+#define CICR0_DMAEN	(1 << 31)	/* DMA request enable */
+#define CICR0_PAR_EN	(1 << 30)	/* Parity enable */
+#define CICR0_SL_CAP_EN	(1 << 29)	/* Capture enable for slave mode */
+#define CICR0_ENB	(1 << 28)	/* Camera interface enable */
+#define CICR0_DIS	(1 << 27)	/* Camera interface disable */
+#define CICR0_SIM	(0x7 << 24)	/* Sensor interface mode mask */
+#define CICR0_TOM	(1 << 9)	/* Time-out mask */
+#define CICR0_RDAVM	(1 << 8)	/* Receive-data-available mask */
+#define CICR0_FEM	(1 << 7)	/* FIFO-empty mask */
+#define CICR0_EOLM	(1 << 6)	/* End-of-line mask */
+#define CICR0_PERRM	(1 << 5)	/* Parity-error mask */
+#define CICR0_QDM	(1 << 4)	/* Quick-disable mask */
+#define CICR0_CDM	(1 << 3)	/* Disable-done mask */
+#define CICR0_SOFM	(1 << 2)	/* Start-of-frame mask */
+#define CICR0_EOFM	(1 << 1)	/* End-of-frame mask */
+#define CICR0_FOM	(1 << 0)	/* FIFO-overrun mask */
+
+#define CICR1_TBIT	(1 << 31)	/* Transparency bit */
+#define CICR1_RGBT_CONV	(0x3 << 29)	/* RGBT conversion mask */
+#define CICR1_PPL	(0x7ff << 15)	/* Pixels per line mask */
+#define CICR1_RGB_CONV	(0x7 << 12)	/* RGB conversion mask */
+#define CICR1_RGB_F	(1 << 11)	/* RGB format */
+#define CICR1_YCBCR_F	(1 << 10)	/* YCbCr format */
+#define CICR1_RGB_BPP	(0x7 << 7)	/* RGB bis per pixel mask */
+#define CICR1_RAW_BPP	(0x3 << 5)	/* Raw bis per pixel mask */
+#define CICR1_COLOR_SP	(0x3 << 3)	/* Color space mask */
+#define CICR1_DW	(0x7 << 0)	/* Data width mask */
+
+#define CICR2_BLW	(0xff << 24)	/* Beginning-of-line pixel clock
+					   wait count mask */
+#define CICR2_ELW	(0xff << 16)	/* End-of-line pixel clock
+					   wait count mask */
+#define CICR2_HSW	(0x3f << 10)	/* Horizontal sync pulse width mask */
+#define CICR2_BFPW	(0x3f << 3)	/* Beginning-of-frame pixel clock
+					   wait count mask */
+#define CICR2_FSW	(0x7 << 0)	/* Frame stabilization
+					   wait count mask */
+
+#define CICR3_BFW	(0xff << 24)	/* Beginning-of-frame line clock
+					   wait count mask */
+#define CICR3_EFW	(0xff << 16)	/* End-of-frame line clock
+					   wait count mask */
+#define CICR3_VSW	(0x3f << 10)	/* Vertical sync pulse width mask */
+#define CICR3_BFPW	(0x3f << 3)	/* Beginning-of-frame pixel clock
+					   wait count mask */
+#define CICR3_LPF	(0x7ff << 0)	/* Lines per frame mask */
+
+#define CICR4_MCLK_DLY	(0x3 << 24)	/* MCLK Data Capture Delay mask */
+#define CICR4_PCLK_EN	(1 << 23)	/* Pixel clock enable */
+#define CICR4_PCP	(1 << 22)	/* Pixel clock polarity */
+#define CICR4_HSP	(1 << 21)	/* Horizontal sync polarity */
+#define CICR4_VSP	(1 << 20)	/* Vertical sync polarity */
+#define CICR4_MCLK_EN	(1 << 19)	/* MCLK enable */
+#define CICR4_FR_RATE	(0x7 << 8)	/* Frame rate mask */
+#define CICR4_DIV	(0xff << 0)	/* Clock divisor mask */
+
+#define CISR_FTO	(1 << 15)	/* FIFO time-out */
+#define CISR_RDAV_2	(1 << 14)	/* Channel 2 receive data available */
+#define CISR_RDAV_1	(1 << 13)	/* Channel 1 receive data available */
+#define CISR_RDAV_0	(1 << 12)	/* Channel 0 receive data available */
+#define CISR_FEMPTY_2	(1 << 11)	/* Channel 2 FIFO empty */
+#define CISR_FEMPTY_1	(1 << 10)	/* Channel 1 FIFO empty */
+#define CISR_FEMPTY_0	(1 << 9)	/* Channel 0 FIFO empty */
+#define CISR_EOL	(1 << 8)	/* End of line */
+#define CISR_PAR_ERR	(1 << 7)	/* Parity error */
+#define CISR_CQD	(1 << 6)	/* Camera interface quick disable */
+#define CISR_CDD	(1 << 5)	/* Camera interface disable done */
+#define CISR_SOF	(1 << 4)	/* Start of frame */
+#define CISR_EOF	(1 << 3)	/* End of frame */
+#define CISR_IFO_2	(1 << 2)	/* FIFO overrun for Channel 2 */
+#define CISR_IFO_1	(1 << 1)	/* FIFO overrun for Channel 1 */
+#define CISR_IFO_0	(1 << 0)	/* FIFO overrun for Channel 0 */
+
+#define CIFR_FLVL2	(0x7f << 23)	/* FIFO 2 level mask */
+#define CIFR_FLVL1	(0x7f << 16)	/* FIFO 1 level mask */
+#define CIFR_FLVL0	(0xff << 8)	/* FIFO 0 level mask */
+#define CIFR_THL_0	(0x3 << 4)	/* Threshold Level for Channel 0 FIFO */
+#define CIFR_RESET_F	(1 << 3)	/* Reset input FIFOs */
+#define CIFR_FEN2	(1 << 2)	/* FIFO enable for channel 2 */
+#define CIFR_FEN1	(1 << 1)	/* FIFO enable for channel 1 */
+#define CIFR_FEN0	(1 << 0)	/* FIFO enable for channel 0 */
+

drivers/mtd/nand/pxa3xx_nand.c

@@ -20,8 +20,8 @@
 #include <linux/mtd/partitions.h>
 #include <linux/io.h>
 #include <linux/irq.h>
-#include <asm/dma.h>
 
+#include <mach/dma.h>
 #include <mach/pxa-regs.h>
 #include <mach/pxa3xx_nand.h>
 

drivers/net/irda/pxaficp_ir.c

@@ -26,6 +26,49 @@
 #include <mach/irda.h>
 #include <mach/hardware.h>
 #include <mach/pxa-regs.h>
+#include <mach/regs-uart.h>
+
+#define FICP		__REG(0x40800000)  /* Start of FICP area */
+#define ICCR0		__REG(0x40800000)  /* ICP Control Register 0 */
+#define ICCR1		__REG(0x40800004)  /* ICP Control Register 1 */
+#define ICCR2		__REG(0x40800008)  /* ICP Control Register 2 */
+#define ICDR		__REG(0x4080000c)  /* ICP Data Register */
+#define ICSR0		__REG(0x40800014)  /* ICP Status Register 0 */
+#define ICSR1		__REG(0x40800018)  /* ICP Status Register 1 */
+
+#define ICCR0_AME	(1 << 7)	/* Address match enable */
+#define ICCR0_TIE	(1 << 6)	/* Transmit FIFO interrupt enable */
+#define ICCR0_RIE	(1 << 5)	/* Recieve FIFO interrupt enable */
+#define ICCR0_RXE	(1 << 4)	/* Receive enable */
+#define ICCR0_TXE	(1 << 3)	/* Transmit enable */
+#define ICCR0_TUS	(1 << 2)	/* Transmit FIFO underrun select */
+#define ICCR0_LBM	(1 << 1)	/* Loopback mode */
+#define ICCR0_ITR	(1 << 0)	/* IrDA transmission */
+
+#define ICCR2_RXP       (1 << 3)	/* Receive Pin Polarity select */
+#define ICCR2_TXP       (1 << 2)	/* Transmit Pin Polarity select */
+#define ICCR2_TRIG	(3 << 0)	/* Receive FIFO Trigger threshold */
+#define ICCR2_TRIG_8    (0 << 0)	/* 	>= 8 bytes */
+#define ICCR2_TRIG_16   (1 << 0)	/*	>= 16 bytes */
+#define ICCR2_TRIG_32   (2 << 0)	/*	>= 32 bytes */
+
+#ifdef CONFIG_PXA27x
+#define ICSR0_EOC	(1 << 6)	/* DMA End of Descriptor Chain */
+#endif
+#define ICSR0_FRE	(1 << 5)	/* Framing error */
+#define ICSR0_RFS	(1 << 4)	/* Receive FIFO service request */
+#define ICSR0_TFS	(1 << 3)	/* Transnit FIFO service request */
+#define ICSR0_RAB	(1 << 2)	/* Receiver abort */
+#define ICSR0_TUR	(1 << 1)	/* Trunsmit FIFO underun */
+#define ICSR0_EIF	(1 << 0)	/* End/Error in FIFO */
+
+#define ICSR1_ROR	(1 << 6)	/* Receiver FIFO underrun  */
+#define ICSR1_CRE	(1 << 5)	/* CRC error */
+#define ICSR1_EOF	(1 << 4)	/* End of frame */
+#define ICSR1_TNF	(1 << 3)	/* Transmit FIFO not full */
+#define ICSR1_RNE	(1 << 2)	/* Receive FIFO not empty */
+#define ICSR1_TBY	(1 << 1)	/* Tramsmiter busy flag */
+#define ICSR1_RSY	(1 << 0)	/* Recevier synchronized flag */
 
 #define IrSR_RXPL_NEG_IS_ZERO (1<<4)
 #define IrSR_RXPL_POS_IS_ZERO 0x0

drivers/net/smc911x.h

@@ -200,6 +200,9 @@ static inline void SMC_outsl(struct smc911x_local *lp, int reg,
 
 
 #ifdef SMC_USE_PXA_DMA
+
+#include <mach/dma.h>
+
 /*
  * Define the request and free functions
  * These are unfortunately architecture specific as no generic allocation

drivers/serial/pxa.c

@@ -48,6 +48,7 @@
 #include <mach/hardware.h>
 #include <asm/irq.h>
 #include <mach/pxa-regs.h>
+#include <mach/regs-uart.h>
 
 
 struct uart_pxa_port {

drivers/video/pxafb.c

@@ -69,9 +69,6 @@
 #define LCCR3_INVALID_CONFIG_MASK	(LCCR3_HSP | LCCR3_VSP |\
 					 LCCR3_PCD | LCCR3_BPP)
 
-static void (*pxafb_backlight_power)(int);
-static void (*pxafb_lcd_power)(int, struct fb_var_screeninfo *);
-
 static int pxafb_activate_var(struct fb_var_screeninfo *var,
 				struct pxafb_info *);
 static void set_ctrlr_state(struct pxafb_info *fbi, u_int state);
@@ -814,6 +811,7 @@ static int pxafb_smart_init(struct pxafb_info *fbi)
 				__func__);
 		return PTR_ERR(fbi->smart_thread);
 	}
+
 	return 0;
 }
 #else
@@ -976,16 +974,16 @@ static inline void __pxafb_backlight_power(struct pxafb_info *fbi, int on)
 {
 	pr_debug("pxafb: backlight o%s\n", on ? "n" : "ff");
 
-	if (pxafb_backlight_power)
-		pxafb_backlight_power(on);
+	if (fbi->backlight_power)
+		fbi->backlight_power(on);
 }
 
 static inline void __pxafb_lcd_power(struct pxafb_info *fbi, int on)
 {
 	pr_debug("pxafb: LCD power o%s\n", on ? "n" : "ff");
 
-	if (pxafb_lcd_power)
-		pxafb_lcd_power(on, &fbi->fb.var);
+	if (fbi->lcd_power)
+		fbi->lcd_power(on, &fbi->fb.var);
 }
 
 static void pxafb_setup_gpio(struct pxafb_info *fbi)
@@ -1748,8 +1746,7 @@ static int __devinit pxafb_probe(struct platform_device *dev)
 		ret = -EINVAL;
 		goto failed;
 	}
-	pxafb_backlight_power = inf->pxafb_backlight_power;
-	pxafb_lcd_power = inf->pxafb_lcd_power;
+
 	fbi = pxafb_init_fbinfo(&dev->dev);
 	if (!fbi) {
 		/* only reason for pxafb_init_fbinfo to fail is kmalloc */
@@ -1758,6 +1755,9 @@ static int __devinit pxafb_probe(struct platform_device *dev)
 		goto failed;
 	}
 
+	fbi->backlight_power = inf->pxafb_backlight_power;
+	fbi->lcd_power = inf->pxafb_lcd_power;
+
 	r = platform_get_resource(dev, IORESOURCE_MEM, 0);
 	if (r == NULL) {
 		dev_err(&dev->dev, "no I/O memory resource defined\n");

drivers/video/pxafb.h

@@ -124,6 +124,9 @@ struct pxafb_info {
 	struct notifier_block	freq_transition;
 	struct notifier_block	freq_policy;
 #endif
+
+	void (*lcd_power)(int, struct fb_var_screeninfo *);
+	void (*backlight_power)(int);
 };
 
 #define TO_INF(ptr,member) container_of(ptr,struct pxafb_info,member)

sound/arm/pxa2xx-ac97-lib.c

@@ -22,7 +22,7 @@
 
 #include <asm/irq.h>
 #include <mach/hardware.h>
-#include <mach/pxa-regs.h>
+#include <mach/regs-ac97.h>
 #include <mach/pxa2xx-gpio.h>
 #include <mach/audio.h>
 

sound/arm/pxa2xx-ac97.c

@@ -22,6 +22,7 @@
 
 #include <mach/hardware.h>
 #include <mach/pxa-regs.h>
+#include <mach/regs-ac97.h>
 #include <mach/audio.h>
 
 #include "pxa2xx-pcm.h"

sound/arm/pxa2xx-pcm.h

@@ -9,7 +9,7 @@
  * it under the terms of the GNU General Public License version 2 as
  * published by the Free Software Foundation.
  */
-#include <asm/dma.h>
+#include <mach/dma.h>
 
 struct pxa2xx_runtime_data {
 	int dma_ch;

sound/soc/pxa/pxa2xx-ac97.c

@@ -21,6 +21,7 @@
 
 #include <mach/hardware.h>
 #include <mach/pxa-regs.h>
+#include <mach/regs-ac97.h>
 
 #include "pxa2xx-pcm.h"
 #include "pxa2xx-ac97.h"