[ARM PATCH] 2458/1: prevent PXA2xx defines from clashing with SA1111's

Patch from Nicolas Pitre

A more elegant solution could be applied which would require more work.
However there is only one platform using both chips (Lubbock) and half
of the SA1111 features are unusable due to botched DMA support at the
PCB level anyway.  Therefore this solution should be sufficient for
now.
Also removed the SADIV defines which use would not constitute good
programming practice. Divisors should be computed directly in the code
especially since different PXA2xx versions have different clock source
frequencies.  No in-tree driver uses them so this is low impact..
Finally changed alignment to fit rest of file.

Signed-off-by: Nicolas Pitre
Signed-off-by: Russell King

include/asm-arm/arch-pxa/pxa-regs.h

@@ -444,7 +444,8 @@
  */
 
 /* FIXME: This clash with SA1111 defines */
-#ifndef CONFIG_SA1111
+#ifndef _ASM_ARCH_SA1111
+
 #define SACR0		__REG(0x40400000)  /* Global Control Register */
 #define SACR1		__REG(0x40400004)  /* Serial Audio I 2 S/MSB-Justified Control Register */
 #define SASR0		__REG(0x4040000C)  /* Serial Audio I 2 S/MSB-Justified Interface and FIFO Status Register */
@@ -452,7 +453,6 @@
 #define SAICR		__REG(0x40400018)  /* Serial Audio Interrupt Clear Register */
 #define SADIV		__REG(0x40400060)  /* Audio Clock Divider Register. */
 #define SADR		__REG(0x40400080)  /* Serial Audio Data Register (TX and RX FIFO access Register). */
-#endif
 
 #define SACR0_RFTH(x)	(x << 12)	/* Rx FIFO Interrupt or DMA Trigger Threshold */
 #define SACR0_TFTH(x)	(x << 8)	/* Tx FIFO Interrupt or DMA Trigger Threshold */
@@ -461,7 +461,6 @@
 #define SACR0_RST	(1 << 3)	/* FIFO, i2s Register Reset */
 #define SACR0_BCKD	(1 << 2) 	/* Bit Clock Direction */
 #define SACR0_ENB	(1 << 0)	/* Enable I2S Link */
-
 #define SACR1_ENLBF	(1 << 5)	/* Enable Loopback */
 #define SACR1_DRPL	(1 << 4) 	/* Disable Replaying Function */
 #define SACR1_DREC	(1 << 3)	/* Disable Recording Function */
@@ -476,13 +475,6 @@
 #define SASR0_RNE	(1 << 1)	/* Rx FIFO Not Empty */
 #define SASR0_TNF	(1 << 0) 	/* Tx FIFO Not Empty */
 
-#define SADIV_3_058M	0x0c			/* Serial Clock Divider 3.058MHz */
-#define SADIV_2_836M	0x0d			/* 2.836 MHz */
-#define SADIV_1_405M	0x1a			/* 1.405 MHz */
-#define SADIV_1_026M	0x24			/* 1.026 MHz */
-#define SADIV_702K		0x34			/* 702 kHz */
-#define SADIV_513K		0x48			/* 513 kHz */
-
 #define SAICR_ROR	(1 << 6)	/* Clear Rx FIFO Overrun Interrupt */
 #define SAICR_TUR	(1 << 5)	/* Clear Tx FIFO Underrun Interrupt */
 
@@ -491,6 +483,7 @@
 #define SAIMR_RFS	(1 << 4)	/* Enable Rx FIFO Service Interrupt */
 #define SAIMR_TFS	(1 << 3)	/* Enable Tx FIFO Service Interrupt */
 
+#endif
 
 /*
  * AC97 Controller registers