Merge branch 'asix-pm-improvements'

Robert Foss says:

====================
net/usb: asix driver improvements

This is a resubmission of v3, since the netdev
mailinlist was not sent the previous submission.

This series improves power management of the asix driver.

 - Suspend/resume support is improved to save needed registers.
 - Device disconnection is improved.
 - Fixes AX88772x resume failures
 - Implementes IEEE 802.3 spec section "22.2.4.1.1 Reset" correctly
 - Fixes AX_CMD_WRITE_MEDIUM_MODE being set incorrectly

Changes since v1:
- Added proper metadata tags to series.
- Added two more patches to series.

Changes since v2:
- Added coverletter
- Tested patches on AX88772A/AX88772B/AX88178/AX88179 hardware
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/usb/asix.h

@@ -46,6 +46,7 @@
 #define AX_CMD_SET_SW_MII		0x06
 #define AX_CMD_READ_MII_REG		0x07
 #define AX_CMD_WRITE_MII_REG		0x08
+#define AX_CMD_STATMNGSTS_REG		0x09
 #define AX_CMD_SET_HW_MII		0x0a
 #define AX_CMD_READ_EEPROM		0x0b
 #define AX_CMD_WRITE_EEPROM		0x0c
@@ -71,6 +72,17 @@
 #define AX_CMD_SW_RESET			0x20
 #define AX_CMD_SW_PHY_STATUS		0x21
 #define AX_CMD_SW_PHY_SELECT		0x22
+#define AX_QCTCTRL			0x2A
+
+#define AX_CHIPCODE_MASK		0x70
+#define AX_AX88772_CHIPCODE		0x00
+#define AX_AX88772A_CHIPCODE		0x10
+#define AX_AX88772B_CHIPCODE		0x20
+#define AX_HOST_EN			0x01
+
+#define AX_PHYSEL_PSEL			0x01
+#define AX_PHYSEL_SSMII			0
+#define AX_PHYSEL_SSEN			0x10
 
 #define AX_PHY_SELECT_MASK		(BIT(3) | BIT(2))
 #define AX_PHY_SELECT_INTERNAL		0
@@ -173,6 +185,10 @@ struct asix_rx_fixup_info {
 };
 
 struct asix_common_private {
+	void (*resume)(struct usbnet *dev);
+	void (*suspend)(struct usbnet *dev);
+	u16 presvd_phy_advertise;
+	u16 presvd_phy_bmcr;
 	struct asix_rx_fixup_info rx_fixup_info;
 };
 
@@ -182,10 +198,10 @@ extern const struct driver_info ax88172a_info;
 #define FLAG_EEPROM_MAC		(1UL << 0)  /* init device MAC from eeprom */
 
 int asix_read_cmd(struct usbnet *dev, u8 cmd, u16 value, u16 index,
-		  u16 size, void *data);
+		  u16 size, void *data, int in_pm);
 
 int asix_write_cmd(struct usbnet *dev, u8 cmd, u16 value, u16 index,
-		   u16 size, void *data);
+		   u16 size, void *data, int in_pm);
 
 void asix_write_cmd_async(struct usbnet *dev, u8 cmd, u16 value,
 			  u16 index, u16 size, void *data);
@@ -197,27 +213,31 @@ int asix_rx_fixup_common(struct usbnet *dev, struct sk_buff *skb);
 struct sk_buff *asix_tx_fixup(struct usbnet *dev, struct sk_buff *skb,
 			      gfp_t flags);
 
-int asix_set_sw_mii(struct usbnet *dev);
-int asix_set_hw_mii(struct usbnet *dev);
+int asix_set_sw_mii(struct usbnet *dev, int in_pm);
+int asix_set_hw_mii(struct usbnet *dev, int in_pm);
 
 int asix_read_phy_addr(struct usbnet *dev, int internal);
 int asix_get_phy_addr(struct usbnet *dev);
 
-int asix_sw_reset(struct usbnet *dev, u8 flags);
+int asix_sw_reset(struct usbnet *dev, u8 flags, int in_pm);
 
-u16 asix_read_rx_ctl(struct usbnet *dev);
-int asix_write_rx_ctl(struct usbnet *dev, u16 mode);
+u16 asix_read_rx_ctl(struct usbnet *dev, int in_pm);
+int asix_write_rx_ctl(struct usbnet *dev, u16 mode, int in_pm);
 
-u16 asix_read_medium_status(struct usbnet *dev);
-int asix_write_medium_mode(struct usbnet *dev, u16 mode);
+u16 asix_read_medium_status(struct usbnet *dev, int in_pm);
+int asix_write_medium_mode(struct usbnet *dev, u16 mode, int in_pm);
 
-int asix_write_gpio(struct usbnet *dev, u16 value, int sleep);
+int asix_write_gpio(struct usbnet *dev, u16 value, int sleep, int in_pm);
 
 void asix_set_multicast(struct net_device *net);
 
 int asix_mdio_read(struct net_device *netdev, int phy_id, int loc);
 void asix_mdio_write(struct net_device *netdev, int phy_id, int loc, int val);
 
+int asix_mdio_read_nopm(struct net_device *netdev, int phy_id, int loc);
+void asix_mdio_write_nopm(struct net_device *netdev, int phy_id, int loc,
+			  int val);
+
 void asix_get_wol(struct net_device *net, struct ethtool_wolinfo *wolinfo);
 int asix_set_wol(struct net_device *net, struct ethtool_wolinfo *wolinfo);
 

drivers/net/usb/asix_common.c

@@ -22,24 +22,49 @@
 #include "asix.h"
 
 int asix_read_cmd(struct usbnet *dev, u8 cmd, u16 value, u16 index,
-		  u16 size, void *data)
+		  u16 size, void *data, int in_pm)
 {
 	int ret;
-	ret = usbnet_read_cmd(dev, cmd,
-			       USB_DIR_IN | USB_TYPE_VENDOR | USB_RECIP_DEVICE,
+	int (*fn)(struct usbnet *, u8, u8, u16, u16, void *, u16);
+
+	BUG_ON(!dev);
+
+	if (!in_pm)
+		fn = usbnet_read_cmd;
+	else
+		fn = usbnet_read_cmd_nopm;
+
+	ret = fn(dev, cmd, USB_DIR_IN | USB_TYPE_VENDOR | USB_RECIP_DEVICE,
 		 value, index, data, size);
 
-	if (ret != size && ret >= 0)
-		return -EINVAL;
+	if (unlikely(ret < 0))
+		netdev_warn(dev->net, "Failed to read reg index 0x%04x: %d\n",
+			    index, ret);
+
 	return ret;
 }
 
 int asix_write_cmd(struct usbnet *dev, u8 cmd, u16 value, u16 index,
-		   u16 size, void *data)
+		   u16 size, void *data, int in_pm)
 {
-	return usbnet_write_cmd(dev, cmd,
-				USB_DIR_OUT | USB_TYPE_VENDOR | USB_RECIP_DEVICE,
+	int ret;
+	int (*fn)(struct usbnet *, u8, u8, u16, u16, const void *, u16);
+
+	BUG_ON(!dev);
+
+	if (!in_pm)
+		fn = usbnet_write_cmd;
+	else
+		fn = usbnet_write_cmd_nopm;
+
+	ret = fn(dev, cmd, USB_DIR_OUT | USB_TYPE_VENDOR | USB_RECIP_DEVICE,
 		 value, index, data, size);
+
+	if (unlikely(ret < 0))
+		netdev_warn(dev->net, "Failed to write reg index 0x%04x: %d\n",
+			    index, ret);
+
+	return ret;
 }
 
 void asix_write_cmd_async(struct usbnet *dev, u8 cmd, u16 value, u16 index,
@@ -225,19 +250,20 @@ struct sk_buff *asix_tx_fixup(struct usbnet *dev, struct sk_buff *skb,
 	return skb;
 }
 
-int asix_set_sw_mii(struct usbnet *dev)
+int asix_set_sw_mii(struct usbnet *dev, int in_pm)
 {
 	int ret;
-	ret = asix_write_cmd(dev, AX_CMD_SET_SW_MII, 0x0000, 0, 0, NULL);
+	ret = asix_write_cmd(dev, AX_CMD_SET_SW_MII, 0x0000, 0, 0, NULL, in_pm);
+
 	if (ret < 0)
 		netdev_err(dev->net, "Failed to enable software MII access\n");
 	return ret;
 }
 
-int asix_set_hw_mii(struct usbnet *dev)
+int asix_set_hw_mii(struct usbnet *dev, int in_pm)
 {
 	int ret;
-	ret = asix_write_cmd(dev, AX_CMD_SET_HW_MII, 0x0000, 0, 0, NULL);
+	ret = asix_write_cmd(dev, AX_CMD_SET_HW_MII, 0x0000, 0, 0, NULL, in_pm);
 	if (ret < 0)
 		netdev_err(dev->net, "Failed to enable hardware MII access\n");
 	return ret;
@@ -247,7 +273,7 @@ int asix_read_phy_addr(struct usbnet *dev, int internal)
 {
 	int offset = (internal ? 1 : 0);
 	u8 buf[2];
-	int ret = asix_read_cmd(dev, AX_CMD_READ_PHY_ID, 0, 0, 2, buf);
+	int ret = asix_read_cmd(dev, AX_CMD_READ_PHY_ID, 0, 0, 2, buf, 0);
 
 	netdev_dbg(dev->net, "asix_get_phy_addr()\n");
 
@@ -270,21 +296,21 @@ int asix_get_phy_addr(struct usbnet *dev)
 }
 
 
-int asix_sw_reset(struct usbnet *dev, u8 flags)
+int asix_sw_reset(struct usbnet *dev, u8 flags, int in_pm)
 {
 	int ret;
 
-        ret = asix_write_cmd(dev, AX_CMD_SW_RESET, flags, 0, 0, NULL);
+	ret = asix_write_cmd(dev, AX_CMD_SW_RESET, flags, 0, 0, NULL, in_pm);
 	if (ret < 0)
 		netdev_err(dev->net, "Failed to send software reset: %02x\n", ret);
 
 	return ret;
 }
 
-u16 asix_read_rx_ctl(struct usbnet *dev)
+u16 asix_read_rx_ctl(struct usbnet *dev, int in_pm)
 {
 	__le16 v;
-	int ret = asix_read_cmd(dev, AX_CMD_READ_RX_CTL, 0, 0, 2, &v);
+	int ret = asix_read_cmd(dev, AX_CMD_READ_RX_CTL, 0, 0, 2, &v, in_pm);
 
 	if (ret < 0) {
 		netdev_err(dev->net, "Error reading RX_CTL register: %02x\n", ret);
@@ -295,12 +321,12 @@ u16 asix_read_rx_ctl(struct usbnet *dev)
 	return ret;
 }
 
-int asix_write_rx_ctl(struct usbnet *dev, u16 mode)
+int asix_write_rx_ctl(struct usbnet *dev, u16 mode, int in_pm)
 {
 	int ret;
 
 	netdev_dbg(dev->net, "asix_write_rx_ctl() - mode = 0x%04x\n", mode);
-	ret = asix_write_cmd(dev, AX_CMD_WRITE_RX_CTL, mode, 0, 0, NULL);
+	ret = asix_write_cmd(dev, AX_CMD_WRITE_RX_CTL, mode, 0, 0, NULL, in_pm);
 	if (ret < 0)
 		netdev_err(dev->net, "Failed to write RX_CTL mode to 0x%04x: %02x\n",
 			   mode, ret);
@@ -308,10 +334,11 @@ int asix_write_rx_ctl(struct usbnet *dev, u16 mode)
 	return ret;
 }
 
-u16 asix_read_medium_status(struct usbnet *dev)
+u16 asix_read_medium_status(struct usbnet *dev, int in_pm)
 {
 	__le16 v;
-	int ret = asix_read_cmd(dev, AX_CMD_READ_MEDIUM_STATUS, 0, 0, 2, &v);
+	int ret = asix_read_cmd(dev, AX_CMD_READ_MEDIUM_STATUS,
+				0, 0, 2, &v, in_pm);
 
 	if (ret < 0) {
 		netdev_err(dev->net, "Error reading Medium Status register: %02x\n",
@@ -323,12 +350,13 @@ u16 asix_read_medium_status(struct usbnet *dev)
 
 }
 
-int asix_write_medium_mode(struct usbnet *dev, u16 mode)
+int asix_write_medium_mode(struct usbnet *dev, u16 mode, int in_pm)
 {
 	int ret;
 
 	netdev_dbg(dev->net, "asix_write_medium_mode() - mode = 0x%04x\n", mode);
-	ret = asix_write_cmd(dev, AX_CMD_WRITE_MEDIUM_MODE, mode, 0, 0, NULL);
+	ret = asix_write_cmd(dev, AX_CMD_WRITE_MEDIUM_MODE,
+			     mode, 0, 0, NULL, in_pm);
 	if (ret < 0)
 		netdev_err(dev->net, "Failed to write Medium Mode mode to 0x%04x: %02x\n",
 			   mode, ret);
@@ -336,12 +364,12 @@ int asix_write_medium_mode(struct usbnet *dev, u16 mode)
 	return ret;
 }
 
-int asix_write_gpio(struct usbnet *dev, u16 value, int sleep)
+int asix_write_gpio(struct usbnet *dev, u16 value, int sleep, int in_pm)
 {
 	int ret;
 
 	netdev_dbg(dev->net, "asix_write_gpio() - value = 0x%04x\n", value);
-	ret = asix_write_cmd(dev, AX_CMD_WRITE_GPIOS, value, 0, 0, NULL);
+	ret = asix_write_cmd(dev, AX_CMD_WRITE_GPIOS, value, 0, 0, NULL, in_pm);
 	if (ret < 0)
 		netdev_err(dev->net, "Failed to write GPIO value 0x%04x: %02x\n",
 			   value, ret);
@@ -398,12 +426,27 @@ int asix_mdio_read(struct net_device *netdev, int phy_id, int loc)
 {
 	struct usbnet *dev = netdev_priv(netdev);
 	__le16 res;
+	u8 smsr;
+	int i = 0;
+	int ret;
 
 	mutex_lock(&dev->phy_mutex);
-	asix_set_sw_mii(dev);
+	do {
+		ret = asix_set_sw_mii(dev, 0);
+		if (ret == -ENODEV)
+			break;
+		usleep_range(1000, 1100);
+		ret = asix_read_cmd(dev, AX_CMD_STATMNGSTS_REG,
+				    0, 0, 1, &smsr, 0);
+	} while (!(smsr & AX_HOST_EN) && (i++ < 30) && (ret != -ENODEV));
+	if (ret == -ENODEV) {
+		mutex_unlock(&dev->phy_mutex);
+		return ret;
+	}
+
 	asix_read_cmd(dev, AX_CMD_READ_MII_REG, phy_id,
-				(__u16)loc, 2, &res);
-	asix_set_hw_mii(dev);
+				(__u16)loc, 2, &res, 0);
+	asix_set_hw_mii(dev, 0);
 	mutex_unlock(&dev->phy_mutex);
 
 	netdev_dbg(dev->net, "asix_mdio_read() phy_id=0x%02x, loc=0x%02x, returns=0x%04x\n",
@@ -416,13 +459,95 @@ void asix_mdio_write(struct net_device *netdev, int phy_id, int loc, int val)
 {
 	struct usbnet *dev = netdev_priv(netdev);
 	__le16 res = cpu_to_le16(val);
+	u8 smsr;
+	int i = 0;
+	int ret;
 
 	netdev_dbg(dev->net, "asix_mdio_write() phy_id=0x%02x, loc=0x%02x, val=0x%04x\n",
 			phy_id, loc, val);
+
 	mutex_lock(&dev->phy_mutex);
-	asix_set_sw_mii(dev);
-	asix_write_cmd(dev, AX_CMD_WRITE_MII_REG, phy_id, (__u16)loc, 2, &res);
-	asix_set_hw_mii(dev);
+	do {
+		ret = asix_set_sw_mii(dev, 0);
+		if (ret == -ENODEV)
+			break;
+		usleep_range(1000, 1100);
+		ret = asix_read_cmd(dev, AX_CMD_STATMNGSTS_REG,
+				    0, 0, 1, &smsr, 0);
+	} while (!(smsr & AX_HOST_EN) && (i++ < 30) && (ret != -ENODEV));
+	if (ret == -ENODEV) {
+		mutex_unlock(&dev->phy_mutex);
+		return;
+	}
+
+	asix_write_cmd(dev, AX_CMD_WRITE_MII_REG, phy_id,
+		       (__u16)loc, 2, &res, 0);
+	asix_set_hw_mii(dev, 0);
+	mutex_unlock(&dev->phy_mutex);
+}
+
+int asix_mdio_read_nopm(struct net_device *netdev, int phy_id, int loc)
+{
+	struct usbnet *dev = netdev_priv(netdev);
+	__le16 res;
+	u8 smsr;
+	int i = 0;
+	int ret;
+
+	mutex_lock(&dev->phy_mutex);
+	do {
+		ret = asix_set_sw_mii(dev, 1);
+		if (ret == -ENODEV)
+			break;
+		usleep_range(1000, 1100);
+		ret = asix_read_cmd(dev, AX_CMD_STATMNGSTS_REG,
+				    0, 0, 1, &smsr, 1);
+	} while (!(smsr & AX_HOST_EN) && (i++ < 30) && (ret != -ENODEV));
+	if (ret == -ENODEV) {
+		mutex_unlock(&dev->phy_mutex);
+		return ret;
+	}
+
+	asix_read_cmd(dev, AX_CMD_READ_MII_REG, phy_id,
+		      (__u16)loc, 2, &res, 1);
+	asix_set_hw_mii(dev, 1);
+	mutex_unlock(&dev->phy_mutex);
+
+	netdev_dbg(dev->net, "asix_mdio_read_nopm() phy_id=0x%02x, loc=0x%02x, returns=0x%04x\n",
+			phy_id, loc, le16_to_cpu(res));
+
+	return le16_to_cpu(res);
+}
+
+void
+asix_mdio_write_nopm(struct net_device *netdev, int phy_id, int loc, int val)
+{
+	struct usbnet *dev = netdev_priv(netdev);
+	__le16 res = cpu_to_le16(val);
+	u8 smsr;
+	int i = 0;
+	int ret;
+
+	netdev_dbg(dev->net, "asix_mdio_write() phy_id=0x%02x, loc=0x%02x, val=0x%04x\n",
+			phy_id, loc, val);
+
+	mutex_lock(&dev->phy_mutex);
+	do {
+		ret = asix_set_sw_mii(dev, 1);
+		if (ret == -ENODEV)
+			break;
+		usleep_range(1000, 1100);
+		ret = asix_read_cmd(dev, AX_CMD_STATMNGSTS_REG,
+				    0, 0, 1, &smsr, 1);
+	} while (!(smsr & AX_HOST_EN) && (i++ < 30) && (ret != -ENODEV));
+	if (ret == -ENODEV) {
+		mutex_unlock(&dev->phy_mutex);
+		return;
+	}
+
+	asix_write_cmd(dev, AX_CMD_WRITE_MII_REG, phy_id,
+		       (__u16)loc, 2, &res, 1);
+	asix_set_hw_mii(dev, 1);
 	mutex_unlock(&dev->phy_mutex);
 }
 
@@ -431,7 +556,8 @@ void asix_get_wol(struct net_device *net, struct ethtool_wolinfo *wolinfo)
 	struct usbnet *dev = netdev_priv(net);
 	u8 opt;
 
-	if (asix_read_cmd(dev, AX_CMD_READ_MONITOR_MODE, 0, 0, 1, &opt) < 0) {
+	if (asix_read_cmd(dev, AX_CMD_READ_MONITOR_MODE,
+			  0, 0, 1, &opt, 0) < 0) {
 		wolinfo->supported = 0;
 		wolinfo->wolopts = 0;
 		return;
@@ -455,7 +581,7 @@ int asix_set_wol(struct net_device *net, struct ethtool_wolinfo *wolinfo)
 		opt |= AX_MONITOR_MAGIC;
 
 	if (asix_write_cmd(dev, AX_CMD_WRITE_MONITOR_MODE,
-			      opt, 0, 0, NULL) < 0)
+			      opt, 0, 0, NULL, 0) < 0)
 		return -EINVAL;
 
 	return 0;
@@ -490,7 +616,7 @@ int asix_get_eeprom(struct net_device *net, struct ethtool_eeprom *eeprom,
 	/* ax8817x returns 2 bytes from eeprom on read */
 	for (i = first_word; i <= last_word; i++) {
 		if (asix_read_cmd(dev, AX_CMD_READ_EEPROM, i, 0, 2,
-				  &(eeprom_buff[i - first_word])) < 0) {
+				  &eeprom_buff[i - first_word], 0) < 0) {
 			kfree(eeprom_buff);
 			return -EIO;
 		}
@@ -531,7 +657,7 @@ int asix_set_eeprom(struct net_device *net, struct ethtool_eeprom *eeprom,
 	   the EEPROM */
 	if (eeprom->offset & 1) {
 		ret = asix_read_cmd(dev, AX_CMD_READ_EEPROM, first_word, 0, 2,
-				    &(eeprom_buff[0]));
+				    &eeprom_buff[0], 0);
 		if (ret < 0) {
 			netdev_err(net, "Failed to read EEPROM at offset 0x%02x.\n", first_word);
 			goto free;
@@ -540,7 +666,7 @@ int asix_set_eeprom(struct net_device *net, struct ethtool_eeprom *eeprom,
 
 	if ((eeprom->offset + eeprom->len) & 1) {
 		ret = asix_read_cmd(dev, AX_CMD_READ_EEPROM, last_word, 0, 2,
-				    &(eeprom_buff[last_word - first_word]));
+				    &eeprom_buff[last_word - first_word], 0);
 		if (ret < 0) {
 			netdev_err(net, "Failed to read EEPROM at offset 0x%02x.\n", last_word);
 			goto free;
@@ -550,7 +676,7 @@ int asix_set_eeprom(struct net_device *net, struct ethtool_eeprom *eeprom,
 	memcpy((u8 *)eeprom_buff + (eeprom->offset & 1), data, eeprom->len);
 
 	/* write data to EEPROM */
-	ret = asix_write_cmd(dev, AX_CMD_WRITE_ENABLE, 0x0000, 0, 0, NULL);
+	ret = asix_write_cmd(dev, AX_CMD_WRITE_ENABLE, 0x0000, 0, 0, NULL, 0);
 	if (ret < 0) {
 		netdev_err(net, "Failed to enable EEPROM write\n");
 		goto free;
@@ -561,7 +687,7 @@ int asix_set_eeprom(struct net_device *net, struct ethtool_eeprom *eeprom,
 		netdev_dbg(net, "write to EEPROM at offset 0x%02x, data 0x%04x\n",
 			   i, eeprom_buff[i - first_word]);
 		ret = asix_write_cmd(dev, AX_CMD_WRITE_EEPROM, i,
-				     eeprom_buff[i - first_word], 0, NULL);
+				     eeprom_buff[i - first_word], 0, NULL, 0);
 		if (ret < 0) {
 			netdev_err(net, "Failed to write EEPROM at offset 0x%02x.\n",
 				   i);
@@ -570,7 +696,7 @@ int asix_set_eeprom(struct net_device *net, struct ethtool_eeprom *eeprom,
 		msleep(20);
 	}
 
-	ret = asix_write_cmd(dev, AX_CMD_WRITE_DISABLE, 0x0000, 0, 0, NULL);
+	ret = asix_write_cmd(dev, AX_CMD_WRITE_DISABLE, 0x0000, 0, 0, NULL, 0);
 	if (ret < 0) {
 		netdev_err(net, "Failed to disable EEPROM write\n");
 		goto free;

drivers/net/usb/asix_devices.c

@@ -35,6 +35,15 @@
 
 #define	PHY_MODE_RTL8211CL	0x000C
 
+#define AX88772A_PHY14H		0x14
+#define AX88772A_PHY14H_DEFAULT 0x442C
+
+#define AX88772A_PHY15H		0x15
+#define AX88772A_PHY15H_DEFAULT 0x03C8
+
+#define AX88772A_PHY16H		0x16
+#define AX88772A_PHY16H_DEFAULT 0x4044
+
 struct ax88172_int_data {
 	__le16 res1;
 	u8 link;
@@ -79,6 +88,8 @@ static u32 asix_get_phyid(struct usbnet *dev)
 	/* Poll for the rare case the FW or phy isn't ready yet.  */
 	for (i = 0; i < 100; i++) {
 		phy_reg = asix_mdio_read(dev->net, dev->mii.phy_id, MII_PHYSID1);
+		if (phy_reg < 0)
+			return 0;
 		if (phy_reg != 0 && phy_reg != 0xFFFF)
 			break;
 		mdelay(1);
@@ -184,7 +195,7 @@ static int ax88172_link_reset(struct usbnet *dev)
 	netdev_dbg(dev->net, "ax88172_link_reset() speed: %u duplex: %d setting mode to 0x%04x\n",
 		   ethtool_cmd_speed(&ecmd), ecmd.duplex, mode);
 
-	asix_write_medium_mode(dev, mode);
+	asix_write_medium_mode(dev, mode, 0);
 
 	return 0;
 }
@@ -201,6 +212,28 @@ static const struct net_device_ops ax88172_netdev_ops = {
 	.ndo_set_rx_mode	= ax88172_set_multicast,
 };
 
+static void asix_phy_reset(struct usbnet *dev, unsigned int reset_bits)
+{
+	unsigned int timeout = 5000;
+
+	asix_mdio_write(dev->net, dev->mii.phy_id, MII_BMCR, reset_bits);
+
+	/* give phy_id a chance to process reset */
+	udelay(500);
+
+	/* See IEEE 802.3 "22.2.4.1.1 Reset": 500ms max */
+	while (timeout--) {
+		if (asix_mdio_read(dev->net, dev->mii.phy_id, MII_BMCR)
+							& BMCR_RESET)
+			udelay(100);
+		else
+			return;
+	}
+
+	netdev_err(dev->net, "BMCR_RESET timeout on phy_id %d\n",
+		   dev->mii.phy_id);
+}
+
 static int ax88172_bind(struct usbnet *dev, struct usb_interface *intf)
 {
 	int ret = 0;
@@ -213,18 +246,19 @@ static int ax88172_bind(struct usbnet *dev, struct usb_interface *intf)
 	/* Toggle the GPIOs in a manufacturer/model specific way */
 	for (i = 2; i >= 0; i--) {
 		ret = asix_write_cmd(dev, AX_CMD_WRITE_GPIOS,
-				(gpio_bits >> (i * 8)) & 0xff, 0, 0, NULL);
+				(gpio_bits >> (i * 8)) & 0xff, 0, 0, NULL, 0);
 		if (ret < 0)
 			goto out;
 		msleep(5);
 	}
 
-	ret = asix_write_rx_ctl(dev, 0x80);
+	ret = asix_write_rx_ctl(dev, 0x80, 0);
 	if (ret < 0)
 		goto out;
 
 	/* Get the MAC address */
-	ret = asix_read_cmd(dev, AX88172_CMD_READ_NODE_ID, 0, 0, ETH_ALEN, buf);
+	ret = asix_read_cmd(dev, AX88172_CMD_READ_NODE_ID,
+			    0, 0, ETH_ALEN, buf, 0);
 	if (ret < 0) {
 		netdev_dbg(dev->net, "read AX_CMD_READ_NODE_ID failed: %d\n",
 			   ret);
@@ -246,7 +280,7 @@ static int ax88172_bind(struct usbnet *dev, struct usb_interface *intf)
 	dev->net->needed_headroom = 4; /* cf asix_tx_fixup() */
 	dev->net->needed_tailroom = 4; /* cf asix_tx_fixup() */
 
-	asix_mdio_write(dev->net, dev->mii.phy_id, MII_BMCR, BMCR_RESET);
+	asix_phy_reset(dev, BMCR_RESET);
 	asix_mdio_write(dev->net, dev->mii.phy_id, MII_ADVERTISE,
 		ADVERTISE_ALL | ADVERTISE_CSMA | ADVERTISE_PAUSE_CAP);
 	mii_nway_restart(&dev->mii);
@@ -290,86 +324,226 @@ static int ax88772_link_reset(struct usbnet *dev)
 	netdev_dbg(dev->net, "ax88772_link_reset() speed: %u duplex: %d setting mode to 0x%04x\n",
 		   ethtool_cmd_speed(&ecmd), ecmd.duplex, mode);
 
-	asix_write_medium_mode(dev, mode);
+	asix_write_medium_mode(dev, mode, 0);
 
 	return 0;
 }
 
 static int ax88772_reset(struct usbnet *dev)
+{
+	struct asix_data *data = (struct asix_data *)&dev->data;
+	int ret;
+
+	/* Rewrite MAC address */
+	ether_addr_copy(data->mac_addr, dev->net->dev_addr);
+	ret = asix_write_cmd(dev, AX_CMD_WRITE_NODE_ID, 0, 0,
+			     ETH_ALEN, data->mac_addr, 0);
+	if (ret < 0)
+		goto out;
+
+	/* Set RX_CTL to default values with 2k buffer, and enable cactus */
+	ret = asix_write_rx_ctl(dev, AX_DEFAULT_RX_CTL, 0);
+	if (ret < 0)
+		goto out;
+
+	asix_write_medium_mode(dev, AX88772_MEDIUM_DEFAULT, 0);
+	if (ret < 0)
+		goto out;
+
+	return 0;
+
+out:
+	return ret;
+}
+
+static int ax88772_hw_reset(struct usbnet *dev, int in_pm)
 {
 	struct asix_data *data = (struct asix_data *)&dev->data;
 	int ret, embd_phy;
 	u16 rx_ctl;
 
-	ret = asix_write_gpio(dev,
-			AX_GPIO_RSE | AX_GPIO_GPO_2 | AX_GPIO_GPO2EN, 5);
+	ret = asix_write_gpio(dev, AX_GPIO_RSE | AX_GPIO_GPO_2 |
+			      AX_GPIO_GPO2EN, 5, in_pm);
 	if (ret < 0)
 		goto out;
 
-	embd_phy = ((asix_get_phy_addr(dev) & 0x1f) == 0x10 ? 1 : 0);
+	embd_phy = ((dev->mii.phy_id & 0x1f) == 0x10 ? 1 : 0);
 
-	ret = asix_write_cmd(dev, AX_CMD_SW_PHY_SELECT, embd_phy, 0, 0, NULL);
+	ret = asix_write_cmd(dev, AX_CMD_SW_PHY_SELECT, embd_phy,
+			     0, 0, NULL, in_pm);
 	if (ret < 0) {
 		netdev_dbg(dev->net, "Select PHY #1 failed: %d\n", ret);
 		goto out;
 	}
 
-	ret = asix_sw_reset(dev, AX_SWRESET_IPPD | AX_SWRESET_PRL);
+	if (embd_phy) {
+		ret = asix_sw_reset(dev, AX_SWRESET_IPPD, in_pm);
 		if (ret < 0)
 			goto out;
 
-	msleep(150);
+		usleep_range(10000, 11000);
 
-	ret = asix_sw_reset(dev, AX_SWRESET_CLEAR);
+		ret = asix_sw_reset(dev, AX_SWRESET_CLEAR, in_pm);
 		if (ret < 0)
 			goto out;
 
-	msleep(150);
+		msleep(60);
 
-	if (embd_phy) {
-		ret = asix_sw_reset(dev, AX_SWRESET_IPRL);
+		ret = asix_sw_reset(dev, AX_SWRESET_IPRL | AX_SWRESET_PRL,
+				    in_pm);
 		if (ret < 0)
 			goto out;
 	} else {
-		ret = asix_sw_reset(dev, AX_SWRESET_PRTE);
+		ret = asix_sw_reset(dev, AX_SWRESET_IPPD | AX_SWRESET_PRL,
+				    in_pm);
 		if (ret < 0)
 			goto out;
 	}
 
 	msleep(150);
-	rx_ctl = asix_read_rx_ctl(dev);
-	netdev_dbg(dev->net, "RX_CTL is 0x%04x after software reset\n", rx_ctl);
-	ret = asix_write_rx_ctl(dev, 0x0000);
+
+	if (in_pm && (!asix_mdio_read_nopm(dev->net, dev->mii.phy_id,
+					   MII_PHYSID1))){
+		ret = -EIO;
+		goto out;
+	}
+
+	ret = asix_write_rx_ctl(dev, AX_DEFAULT_RX_CTL, in_pm);
+	if (ret < 0)
+		goto out;
+
+	ret = asix_write_medium_mode(dev, AX88772_MEDIUM_DEFAULT, in_pm);
 	if (ret < 0)
 		goto out;
 
-	rx_ctl = asix_read_rx_ctl(dev);
-	netdev_dbg(dev->net, "RX_CTL is 0x%04x setting to 0x0000\n", rx_ctl);
+	ret = asix_write_cmd(dev, AX_CMD_WRITE_IPG0,
+			     AX88772_IPG0_DEFAULT | AX88772_IPG1_DEFAULT,
+			     AX88772_IPG2_DEFAULT, 0, NULL, in_pm);
+	if (ret < 0) {
+		netdev_dbg(dev->net, "Write IPG,IPG1,IPG2 failed: %d\n", ret);
+		goto out;
+	}
+
+	/* Rewrite MAC address */
+	ether_addr_copy(data->mac_addr, dev->net->dev_addr);
+	ret = asix_write_cmd(dev, AX_CMD_WRITE_NODE_ID, 0, 0,
+			     ETH_ALEN, data->mac_addr, in_pm);
+	if (ret < 0)
+		goto out;
 
-	ret = asix_sw_reset(dev, AX_SWRESET_PRL);
+	/* Set RX_CTL to default values with 2k buffer, and enable cactus */
+	ret = asix_write_rx_ctl(dev, AX_DEFAULT_RX_CTL, in_pm);
 	if (ret < 0)
 		goto out;
 
-	msleep(150);
+	rx_ctl = asix_read_rx_ctl(dev, in_pm);
+	netdev_dbg(dev->net, "RX_CTL is 0x%04x after all initializations\n",
+		   rx_ctl);
+
+	rx_ctl = asix_read_medium_status(dev, in_pm);
+	netdev_dbg(dev->net,
+		   "Medium Status is 0x%04x after all initializations\n",
+		   rx_ctl);
+
+	return 0;
+
+out:
+	return ret;
+}
+
+static int ax88772a_hw_reset(struct usbnet *dev, int in_pm)
+{
+	struct asix_data *data = (struct asix_data *)&dev->data;
+	int ret, embd_phy;
+	u16 rx_ctl, phy14h, phy15h, phy16h;
+	u8 chipcode = 0;
 
-	ret = asix_sw_reset(dev, AX_SWRESET_IPRL | AX_SWRESET_PRL);
+	ret = asix_write_gpio(dev, AX_GPIO_RSE, 5, in_pm);
 	if (ret < 0)
 		goto out;
 
-	msleep(150);
+	embd_phy = ((dev->mii.phy_id & 0x1f) == 0x10 ? 1 : 0);
 
-	asix_mdio_write(dev->net, dev->mii.phy_id, MII_BMCR, BMCR_RESET);
-	asix_mdio_write(dev->net, dev->mii.phy_id, MII_ADVERTISE,
-			ADVERTISE_ALL | ADVERTISE_CSMA);
-	mii_nway_restart(&dev->mii);
+	ret = asix_write_cmd(dev, AX_CMD_SW_PHY_SELECT, embd_phy |
+			     AX_PHYSEL_SSEN, 0, 0, NULL, in_pm);
+	if (ret < 0) {
+		netdev_dbg(dev->net, "Select PHY #1 failed: %d\n", ret);
+		goto out;
+	}
+	usleep_range(10000, 11000);
+
+	ret = asix_sw_reset(dev, AX_SWRESET_IPPD | AX_SWRESET_IPRL, in_pm);
+	if (ret < 0)
+		goto out;
 
-	ret = asix_write_medium_mode(dev, AX88772_MEDIUM_DEFAULT);
+	usleep_range(10000, 11000);
+
+	ret = asix_sw_reset(dev, AX_SWRESET_IPRL, in_pm);
+	if (ret < 0)
+		goto out;
+
+	msleep(160);
+
+	ret = asix_sw_reset(dev, AX_SWRESET_CLEAR, in_pm);
+	if (ret < 0)
+		goto out;
+
+	ret = asix_sw_reset(dev, AX_SWRESET_IPRL, in_pm);
+	if (ret < 0)
+		goto out;
+
+	msleep(200);
+
+	if (in_pm && (!asix_mdio_read_nopm(dev->net, dev->mii.phy_id,
+					   MII_PHYSID1))) {
+		ret = -1;
+		goto out;
+	}
+
+	ret = asix_read_cmd(dev, AX_CMD_STATMNGSTS_REG, 0,
+			    0, 1, &chipcode, in_pm);
 	if (ret < 0)
 		goto out;
 
+	if ((chipcode & AX_CHIPCODE_MASK) == AX_AX88772B_CHIPCODE) {
+		ret = asix_write_cmd(dev, AX_QCTCTRL, 0x8000, 0x8001,
+				     0, NULL, in_pm);
+		if (ret < 0) {
+			netdev_dbg(dev->net, "Write BQ setting failed: %d\n",
+				   ret);
+			goto out;
+		}
+	} else if ((chipcode & AX_CHIPCODE_MASK) == AX_AX88772A_CHIPCODE) {
+		/* Check if the PHY registers have default settings */
+		phy14h = asix_mdio_read_nopm(dev->net, dev->mii.phy_id,
+					     AX88772A_PHY14H);
+		phy15h = asix_mdio_read_nopm(dev->net, dev->mii.phy_id,
+					     AX88772A_PHY15H);
+		phy16h = asix_mdio_read_nopm(dev->net, dev->mii.phy_id,
+					     AX88772A_PHY16H);
+
+		netdev_dbg(dev->net,
+			   "772a_hw_reset: MR20=0x%x MR21=0x%x MR22=0x%x\n",
+			   phy14h, phy15h, phy16h);
+
+		/* Restore PHY registers default setting if not */
+		if (phy14h != AX88772A_PHY14H_DEFAULT)
+			asix_mdio_write_nopm(dev->net, dev->mii.phy_id,
+					     AX88772A_PHY14H,
+					     AX88772A_PHY14H_DEFAULT);
+		if (phy15h != AX88772A_PHY15H_DEFAULT)
+			asix_mdio_write_nopm(dev->net, dev->mii.phy_id,
+					     AX88772A_PHY15H,
+					     AX88772A_PHY15H_DEFAULT);
+		if (phy16h != AX88772A_PHY16H_DEFAULT)
+			asix_mdio_write_nopm(dev->net, dev->mii.phy_id,
+					     AX88772A_PHY16H,
+					     AX88772A_PHY16H_DEFAULT);
+	}
+
 	ret = asix_write_cmd(dev, AX_CMD_WRITE_IPG0,
 				AX88772_IPG0_DEFAULT | AX88772_IPG1_DEFAULT,
-				AX88772_IPG2_DEFAULT, 0, NULL);
+				AX88772_IPG2_DEFAULT, 0, NULL, in_pm);
 	if (ret < 0) {
 		netdev_dbg(dev->net, "Write IPG,IPG1,IPG2 failed: %d\n", ret);
 		goto out;
@@ -378,20 +552,29 @@ static int ax88772_reset(struct usbnet *dev)
 	/* Rewrite MAC address */
 	memcpy(data->mac_addr, dev->net->dev_addr, ETH_ALEN);
 	ret = asix_write_cmd(dev, AX_CMD_WRITE_NODE_ID, 0, 0, ETH_ALEN,
-							data->mac_addr);
+							data->mac_addr, in_pm);
 	if (ret < 0)
 		goto out;
 
 	/* Set RX_CTL to default values with 2k buffer, and enable cactus */
-	ret = asix_write_rx_ctl(dev, AX_DEFAULT_RX_CTL);
+	ret = asix_write_rx_ctl(dev, AX_DEFAULT_RX_CTL, in_pm);
 	if (ret < 0)
 		goto out;
 
-	rx_ctl = asix_read_rx_ctl(dev);
+	ret = asix_write_medium_mode(dev, AX88772_MEDIUM_DEFAULT, in_pm);
+	if (ret < 0)
+		return ret;
+
+	/* Set RX_CTL to default values with 2k buffer, and enable cactus */
+	ret = asix_write_rx_ctl(dev, AX_DEFAULT_RX_CTL, in_pm);
+	if (ret < 0)
+		goto out;
+
+	rx_ctl = asix_read_rx_ctl(dev, in_pm);
 	netdev_dbg(dev->net, "RX_CTL is 0x%04x after all initializations\n",
 		   rx_ctl);
 
-	rx_ctl = asix_read_medium_status(dev);
+	rx_ctl = asix_read_medium_status(dev, in_pm);
 	netdev_dbg(dev->net,
 		   "Medium Status is 0x%04x after all initializations\n",
 		   rx_ctl);
@@ -400,7 +583,6 @@ static int ax88772_reset(struct usbnet *dev)
 
 out:
 	return ret;
-
 }
 
 static const struct net_device_ops ax88772_netdev_ops = {
@@ -415,11 +597,97 @@ static const struct net_device_ops ax88772_netdev_ops = {
 	.ndo_set_rx_mode        = asix_set_multicast,
 };
 
+static void ax88772_suspend(struct usbnet *dev)
+{
+	struct asix_common_private *priv = dev->driver_priv;
+	u16 medium;
+
+	/* Stop MAC operation */
+	medium = asix_read_medium_status(dev, 0);
+	medium &= ~AX_MEDIUM_RE;
+	asix_write_medium_mode(dev, medium, 0);
+
+	netdev_dbg(dev->net, "ax88772_suspend: medium=0x%04x\n",
+		   asix_read_medium_status(dev, 0));
+
+	/* Preserve BMCR for restoring */
+	priv->presvd_phy_bmcr =
+		asix_mdio_read_nopm(dev->net, dev->mii.phy_id, MII_BMCR);
+
+	/* Preserve ANAR for restoring */
+	priv->presvd_phy_advertise =
+		asix_mdio_read_nopm(dev->net, dev->mii.phy_id, MII_ADVERTISE);
+}
+
+static int asix_suspend(struct usb_interface *intf, pm_message_t message)
+{
+	struct usbnet *dev = usb_get_intfdata(intf);
+	struct asix_common_private *priv = dev->driver_priv;
+
+	if (priv->suspend)
+		priv->suspend(dev);
+
+	return usbnet_suspend(intf, message);
+}
+
+static void ax88772_restore_phy(struct usbnet *dev)
+{
+	struct asix_common_private *priv = dev->driver_priv;
+
+	if (priv->presvd_phy_advertise) {
+		/* Restore Advertisement control reg */
+		asix_mdio_write_nopm(dev->net, dev->mii.phy_id, MII_ADVERTISE,
+				     priv->presvd_phy_advertise);
+
+		/* Restore BMCR */
+		asix_mdio_write_nopm(dev->net, dev->mii.phy_id, MII_BMCR,
+				     priv->presvd_phy_bmcr);
+
+		mii_nway_restart(&dev->mii);
+		priv->presvd_phy_advertise = 0;
+		priv->presvd_phy_bmcr = 0;
+	}
+}
+
+static void ax88772_resume(struct usbnet *dev)
+{
+	int i;
+
+	for (i = 0; i < 3; i++)
+		if (!ax88772_hw_reset(dev, 1))
+			break;
+	ax88772_restore_phy(dev);
+}
+
+static void ax88772a_resume(struct usbnet *dev)
+{
+	int i;
+
+	for (i = 0; i < 3; i++) {
+		if (!ax88772a_hw_reset(dev, 1))
+			break;
+	}
+
+	ax88772_restore_phy(dev);
+}
+
+static int asix_resume(struct usb_interface *intf)
+{
+	struct usbnet *dev = usb_get_intfdata(intf);
+	struct asix_common_private *priv = dev->driver_priv;
+
+	if (priv->resume)
+		priv->resume(dev);
+
+	return usbnet_resume(intf);
+}
+
 static int ax88772_bind(struct usbnet *dev, struct usb_interface *intf)
 {
-	int ret, embd_phy, i;
-	u8 buf[ETH_ALEN];
+	int ret, i;
+	u8 buf[ETH_ALEN], chipcode = 0;
 	u32 phyid;
+	struct asix_common_private *priv;
 
 	usbnet_get_endpoints(dev,intf);
 
@@ -427,13 +695,13 @@ static int ax88772_bind(struct usbnet *dev, struct usb_interface *intf)
 	if (dev->driver_info->data & FLAG_EEPROM_MAC) {
 		for (i = 0; i < (ETH_ALEN >> 1); i++) {
 			ret = asix_read_cmd(dev, AX_CMD_READ_EEPROM, 0x04 + i,
-					0, 2, buf + i * 2);
+					    0, 2, buf + i * 2, 0);
 			if (ret < 0)
 				break;
 		}
 	} else {
 		ret = asix_read_cmd(dev, AX_CMD_READ_NODE_ID,
-				0, 0, ETH_ALEN, buf);
+				0, 0, ETH_ALEN, buf, 0);
 	}
 
 	if (ret < 0) {
@@ -456,16 +724,11 @@ static int ax88772_bind(struct usbnet *dev, struct usb_interface *intf)
 	dev->net->needed_headroom = 4; /* cf asix_tx_fixup() */
 	dev->net->needed_tailroom = 4; /* cf asix_tx_fixup() */
 
-	embd_phy = ((dev->mii.phy_id & 0x1f) == 0x10 ? 1 : 0);
-
-	/* Reset the PHY to normal operation mode */
-	ret = asix_write_cmd(dev, AX_CMD_SW_PHY_SELECT, embd_phy, 0, 0, NULL);
-	if (ret < 0) {
-		netdev_dbg(dev->net, "Select PHY #1 failed: %d\n", ret);
-		return ret;
-	}
+	asix_read_cmd(dev, AX_CMD_STATMNGSTS_REG, 0, 0, 1, &chipcode, 0);
+	chipcode &= AX_CHIPCODE_MASK;
 
-	ax88772_reset(dev);
+	(chipcode == AX_AX88772_CHIPCODE) ? ax88772_hw_reset(dev, 0) :
+					    ax88772a_hw_reset(dev, 0);
 
 	/* Read PHYID register *AFTER* the PHY was reset properly */
 	phyid = asix_get_phyid(dev);
@@ -482,6 +745,18 @@ static int ax88772_bind(struct usbnet *dev, struct usb_interface *intf)
 	if (!dev->driver_priv)
 		return -ENOMEM;
 
+	priv = dev->driver_priv;
+
+	priv->presvd_phy_bmcr = 0;
+	priv->presvd_phy_advertise = 0;
+	if (chipcode == AX_AX88772_CHIPCODE) {
+		priv->resume = ax88772_resume;
+		priv->suspend = ax88772_suspend;
+	} else {
+		priv->resume = ax88772a_resume;
+		priv->suspend = ax88772_suspend;
+	}
+
 	return 0;
 }
 
@@ -593,12 +868,12 @@ static int ax88178_reset(struct usbnet *dev)
 	int gpio0 = 0;
 	u32 phyid;
 
-	asix_read_cmd(dev, AX_CMD_READ_GPIOS, 0, 0, 1, &status);
+	asix_read_cmd(dev, AX_CMD_READ_GPIOS, 0, 0, 1, &status, 0);
 	netdev_dbg(dev->net, "GPIO Status: 0x%04x\n", status);
 
-	asix_write_cmd(dev, AX_CMD_WRITE_ENABLE, 0, 0, 0, NULL);
-	asix_read_cmd(dev, AX_CMD_READ_EEPROM, 0x0017, 0, 2, &eeprom);
-	asix_write_cmd(dev, AX_CMD_WRITE_DISABLE, 0, 0, 0, NULL);
+	asix_write_cmd(dev, AX_CMD_WRITE_ENABLE, 0, 0, 0, NULL, 0);
+	asix_read_cmd(dev, AX_CMD_READ_EEPROM, 0x0017, 0, 2, &eeprom, 0);
+	asix_write_cmd(dev, AX_CMD_WRITE_DISABLE, 0, 0, 0, NULL, 0);
 
 	netdev_dbg(dev->net, "EEPROM index 0x17 is 0x%04x\n", eeprom);
 
@@ -614,15 +889,16 @@ static int ax88178_reset(struct usbnet *dev)
 	netdev_dbg(dev->net, "GPIO0: %d, PhyMode: %d\n", gpio0, data->phymode);
 
 	/* Power up external GigaPHY through AX88178 GPIO pin */
-	asix_write_gpio(dev, AX_GPIO_RSE | AX_GPIO_GPO_1 | AX_GPIO_GPO1EN, 40);
+	asix_write_gpio(dev, AX_GPIO_RSE | AX_GPIO_GPO_1 |
+			AX_GPIO_GPO1EN, 40, 0);
 	if ((le16_to_cpu(eeprom) >> 8) != 1) {
-		asix_write_gpio(dev, 0x003c, 30);
-		asix_write_gpio(dev, 0x001c, 300);
-		asix_write_gpio(dev, 0x003c, 30);
+		asix_write_gpio(dev, 0x003c, 30, 0);
+		asix_write_gpio(dev, 0x001c, 300, 0);
+		asix_write_gpio(dev, 0x003c, 30, 0);
 	} else {
 		netdev_dbg(dev->net, "gpio phymode == 1 path\n");
-		asix_write_gpio(dev, AX_GPIO_GPO1EN, 30);
-		asix_write_gpio(dev, AX_GPIO_GPO1EN | AX_GPIO_GPO_1, 30);
+		asix_write_gpio(dev, AX_GPIO_GPO1EN, 30, 0);
+		asix_write_gpio(dev, AX_GPIO_GPO1EN | AX_GPIO_GPO_1, 30, 0);
 	}
 
 	/* Read PHYID register *AFTER* powering up PHY */
@@ -630,15 +906,15 @@ static int ax88178_reset(struct usbnet *dev)
 	netdev_dbg(dev->net, "PHYID=0x%08x\n", phyid);
 
 	/* Set AX88178 to enable MII/GMII/RGMII interface for external PHY */
-	asix_write_cmd(dev, AX_CMD_SW_PHY_SELECT, 0, 0, 0, NULL);
+	asix_write_cmd(dev, AX_CMD_SW_PHY_SELECT, 0, 0, 0, NULL, 0);
 
-	asix_sw_reset(dev, 0);
+	asix_sw_reset(dev, 0, 0);
 	msleep(150);
 
-	asix_sw_reset(dev, AX_SWRESET_PRL | AX_SWRESET_IPPD);
+	asix_sw_reset(dev, AX_SWRESET_PRL | AX_SWRESET_IPPD, 0);
 	msleep(150);
 
-	asix_write_rx_ctl(dev, 0);
+	asix_write_rx_ctl(dev, 0, 0);
 
 	if (data->phymode == PHY_MODE_MARVELL) {
 		marvell_phy_init(dev);
@@ -646,27 +922,23 @@ static int ax88178_reset(struct usbnet *dev)
 	} else if (data->phymode == PHY_MODE_RTL8211CL)
 		rtl8211cl_phy_init(dev);
 
-	asix_mdio_write(dev->net, dev->mii.phy_id, MII_BMCR,
-			BMCR_RESET | BMCR_ANENABLE);
+	asix_phy_reset(dev, BMCR_RESET | BMCR_ANENABLE);
 	asix_mdio_write(dev->net, dev->mii.phy_id, MII_ADVERTISE,
 			ADVERTISE_ALL | ADVERTISE_CSMA | ADVERTISE_PAUSE_CAP);
 	asix_mdio_write(dev->net, dev->mii.phy_id, MII_CTRL1000,
 			ADVERTISE_1000FULL);
 
+	asix_write_medium_mode(dev, AX88178_MEDIUM_DEFAULT, 0);
 	mii_nway_restart(&dev->mii);
 
-	ret = asix_write_medium_mode(dev, AX88178_MEDIUM_DEFAULT);
-	if (ret < 0)
-		return ret;
-
 	/* Rewrite MAC address */
 	memcpy(data->mac_addr, dev->net->dev_addr, ETH_ALEN);
 	ret = asix_write_cmd(dev, AX_CMD_WRITE_NODE_ID, 0, 0, ETH_ALEN,
-							data->mac_addr);
+							data->mac_addr, 0);
 	if (ret < 0)
 		return ret;
 
-	ret = asix_write_rx_ctl(dev, AX_DEFAULT_RX_CTL);
+	ret = asix_write_rx_ctl(dev, AX_DEFAULT_RX_CTL, 0);
 	if (ret < 0)
 		return ret;
 
@@ -704,7 +976,7 @@ static int ax88178_link_reset(struct usbnet *dev)
 	netdev_dbg(dev->net, "ax88178_link_reset() speed: %u duplex: %d setting mode to 0x%04x\n",
 		   speed, ecmd.duplex, mode);
 
-	asix_write_medium_mode(dev, mode);
+	asix_write_medium_mode(dev, mode, 0);
 
 	if (data->phymode == PHY_MODE_MARVELL && data->ledmode)
 		marvell_led_status(dev, speed);
@@ -733,15 +1005,15 @@ static void ax88178_set_mfb(struct usbnet *dev)
 		mfb = AX_RX_CTL_MFB_16384;
 	}
 
-	rxctl = asix_read_rx_ctl(dev);
-	asix_write_rx_ctl(dev, (rxctl & ~AX_RX_CTL_MFB_16384) | mfb);
+	rxctl = asix_read_rx_ctl(dev, 0);
+	asix_write_rx_ctl(dev, (rxctl & ~AX_RX_CTL_MFB_16384) | mfb, 0);
 
-	medium = asix_read_medium_status(dev);
+	medium = asix_read_medium_status(dev, 0);
 	if (dev->net->mtu > 1500)
 		medium |= AX_MEDIUM_JFE;
 	else
 		medium &= ~AX_MEDIUM_JFE;
-	asix_write_medium_mode(dev, medium);
+	asix_write_medium_mode(dev, medium, 0);
 
 	if (dev->rx_urb_size > old_rx_urb_size)
 		usbnet_unlink_rx_urbs(dev);
@@ -790,7 +1062,7 @@ static int ax88178_bind(struct usbnet *dev, struct usb_interface *intf)
 	usbnet_get_endpoints(dev,intf);
 
 	/* Get the MAC address */
-	ret = asix_read_cmd(dev, AX_CMD_READ_NODE_ID, 0, 0, ETH_ALEN, buf);
+	ret = asix_read_cmd(dev, AX_CMD_READ_NODE_ID, 0, 0, ETH_ALEN, buf, 0);
 	if (ret < 0) {
 		netdev_dbg(dev->net, "Failed to read MAC address: %d\n", ret);
 		return ret;
@@ -811,10 +1083,10 @@ static int ax88178_bind(struct usbnet *dev, struct usb_interface *intf)
 	dev->net->ethtool_ops = &ax88178_ethtool_ops;
 
 	/* Blink LEDS so users know driver saw dongle */
-	asix_sw_reset(dev, 0);
+	asix_sw_reset(dev, 0, 0);
 	msleep(150);
 
-	asix_sw_reset(dev, AX_SWRESET_PRL | AX_SWRESET_IPPD);
+	asix_sw_reset(dev, AX_SWRESET_PRL | AX_SWRESET_IPPD, 0);
 	msleep(150);
 
 	/* Asix framing packs multiple eth frames into a 2K usb bulk transfer */
@@ -877,7 +1149,7 @@ static const struct driver_info ax88772_info = {
 	.unbind = ax88772_unbind,
 	.status = asix_status,
 	.link_reset = ax88772_link_reset,
-	.reset = ax88772_link_reset,
+	.reset = ax88772_reset,
 	.flags = FLAG_ETHER | FLAG_FRAMING_AX | FLAG_LINK_INTR | FLAG_MULTI_PACKET,
 	.rx_fixup = asix_rx_fixup_common,
 	.tx_fixup = asix_tx_fixup,
@@ -1005,7 +1277,7 @@ static const struct usb_device_id	products [] = {
 }, {
 	// Lenovo U2L100P 10/100
 	USB_DEVICE (0x17ef, 0x7203),
-	.driver_info = (unsigned long) &ax88772_info,
+	.driver_info = (unsigned long)&ax88772b_info,
 }, {
 	// ASIX AX88772B 10/100
 	USB_DEVICE (0x0b95, 0x772b),
@@ -1073,7 +1345,7 @@ static const struct usb_device_id	products [] = {
 }, {
 	// Asus USB Ethernet Adapter
 	USB_DEVICE (0x0b95, 0x7e2b),
-	.driver_info = (unsigned long) &ax88772_info,
+	.driver_info = (unsigned long)&ax88772b_info,
 }, {
 	/* ASIX 88172a demo board */
 	USB_DEVICE(0x0b95, 0x172a),
@@ -1095,8 +1367,8 @@ static struct usb_driver asix_driver = {
 	.name =		DRIVER_NAME,
 	.id_table =	products,
 	.probe =	usbnet_probe,
-	.suspend =	usbnet_suspend,
-	.resume =	usbnet_resume,
+	.suspend =	asix_suspend,
+	.resume =	asix_resume,
 	.disconnect =	usbnet_disconnect,
 	.supports_autosuspend = 1,
 	.disable_hub_initiated_lpm = 1,

drivers/net/usb/ax88172a.c

@@ -81,7 +81,7 @@ static void ax88172a_adjust_link(struct net_device *netdev)
 	}
 
 	if (mode != priv->oldmode) {
-		asix_write_medium_mode(dev, mode);
+		asix_write_medium_mode(dev, mode, 0);
 		priv->oldmode = mode;
 		netdev_dbg(netdev, "speed %u duplex %d, setting mode to 0x%04x\n",
 			   phydev->speed, phydev->duplex, mode);
@@ -176,18 +176,19 @@ static int ax88172a_reset_phy(struct usbnet *dev, int embd_phy)
 {
 	int ret;
 
-	ret = asix_sw_reset(dev, AX_SWRESET_IPPD);
+	ret = asix_sw_reset(dev, AX_SWRESET_IPPD, 0);
 	if (ret < 0)
 		goto err;
 
 	msleep(150);
-	ret = asix_sw_reset(dev, AX_SWRESET_CLEAR);
+	ret = asix_sw_reset(dev, AX_SWRESET_CLEAR, 0);
 	if (ret < 0)
 		goto err;
 
 	msleep(150);
 
-	ret = asix_sw_reset(dev, embd_phy ? AX_SWRESET_IPRL : AX_SWRESET_IPPD);
+	ret = asix_sw_reset(dev, embd_phy ? AX_SWRESET_IPRL : AX_SWRESET_IPPD,
+			    0);
 	if (ret < 0)
 		goto err;
 
@@ -213,7 +214,7 @@ static int ax88172a_bind(struct usbnet *dev, struct usb_interface *intf)
 	dev->driver_priv = priv;
 
 	/* Get the MAC address */
-	ret = asix_read_cmd(dev, AX_CMD_READ_NODE_ID, 0, 0, ETH_ALEN, buf);
+	ret = asix_read_cmd(dev, AX_CMD_READ_NODE_ID, 0, 0, ETH_ALEN, buf, 0);
 	if (ret < 0) {
 		netdev_err(dev->net, "Failed to read MAC address: %d\n", ret);
 		goto free;
@@ -224,7 +225,7 @@ static int ax88172a_bind(struct usbnet *dev, struct usb_interface *intf)
 	dev->net->ethtool_ops = &ax88172a_ethtool_ops;
 
 	/* are we using the internal or the external phy? */
-	ret = asix_read_cmd(dev, AX_CMD_SW_PHY_STATUS, 0, 0, 1, buf);
+	ret = asix_read_cmd(dev, AX_CMD_SW_PHY_STATUS, 0, 0, 1, buf, 0);
 	if (ret < 0) {
 		netdev_err(dev->net, "Failed to read software interface selection register: %d\n",
 			   ret);
@@ -303,20 +304,20 @@ static int ax88172a_reset(struct usbnet *dev)
 	ax88172a_reset_phy(dev, priv->use_embdphy);
 
 	msleep(150);
-	rx_ctl = asix_read_rx_ctl(dev);
+	rx_ctl = asix_read_rx_ctl(dev, 0);
 	netdev_dbg(dev->net, "RX_CTL is 0x%04x after software reset\n", rx_ctl);
-	ret = asix_write_rx_ctl(dev, 0x0000);
+	ret = asix_write_rx_ctl(dev, 0x0000, 0);
 	if (ret < 0)
 		goto out;
 
-	rx_ctl = asix_read_rx_ctl(dev);
+	rx_ctl = asix_read_rx_ctl(dev, 0);
 	netdev_dbg(dev->net, "RX_CTL is 0x%04x setting to 0x0000\n", rx_ctl);
 
 	msleep(150);
 
 	ret = asix_write_cmd(dev, AX_CMD_WRITE_IPG0,
 			     AX88772_IPG0_DEFAULT | AX88772_IPG1_DEFAULT,
-			     AX88772_IPG2_DEFAULT, 0, NULL);
+			     AX88772_IPG2_DEFAULT, 0, NULL, 0);
 	if (ret < 0) {
 		netdev_err(dev->net, "Write IPG,IPG1,IPG2 failed: %d\n", ret);
 		goto out;
@@ -325,20 +326,20 @@ static int ax88172a_reset(struct usbnet *dev)
 	/* Rewrite MAC address */
 	memcpy(data->mac_addr, dev->net->dev_addr, ETH_ALEN);
 	ret = asix_write_cmd(dev, AX_CMD_WRITE_NODE_ID, 0, 0, ETH_ALEN,
-			     data->mac_addr);
+			     data->mac_addr, 0);
 	if (ret < 0)
 		goto out;
 
 	/* Set RX_CTL to default values with 2k buffer, and enable cactus */
-	ret = asix_write_rx_ctl(dev, AX_DEFAULT_RX_CTL);
+	ret = asix_write_rx_ctl(dev, AX_DEFAULT_RX_CTL, 0);
 	if (ret < 0)
 		goto out;
 
-	rx_ctl = asix_read_rx_ctl(dev);
+	rx_ctl = asix_read_rx_ctl(dev, 0);
 	netdev_dbg(dev->net, "RX_CTL is 0x%04x after all initializations\n",
 		   rx_ctl);
 
-	rx_ctl = asix_read_medium_status(dev);
+	rx_ctl = asix_read_medium_status(dev, 0);
 	netdev_dbg(dev->net, "Medium Status is 0x%04x after all initializations\n",
 		   rx_ctl);