drm/i915/guc: always reset GuC before loading firmware

After a suspend-resume cycle, the resumed kernel has no idea what the
booted kernel may have done to the GuC before replacing itself with the
resumed image. In particular, it may have already loaded the GuC with
firmware, which will then cause this kernel's attempt to (re)load the
firmware to fail (GuC program memory is write-once!). The symptoms
(GuC firmware reload fails after hibernation) are further described
in the Bugzilla reference below.

So let's *always* reset the GuC just before (re)loading the firmware;
the hardware should then be in a well-known state, and we may even
avoid some of the issues arising from unpredictable timing.

Also added some more fields & values to the definition of the GUC_STATUS
register, which is the key diagnostic indicator if the GuC load fails.
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Cc: Alex Dai <yu.dai@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=94390Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>

drivers/gpu/drm/i915/i915_guc_reg.h

@@ -27,10 +27,12 @@
 /* Definitions of GuC H/W registers, bits, etc */
 
 #define GUC_STATUS			_MMIO(0xc000)
-#define   GS_MIA_IN_RESET		(1 << 0)
+#define   GS_RESET_SHIFT		0
+#define   GS_MIA_IN_RESET		  (0x01 << GS_RESET_SHIFT)
 #define   GS_BOOTROM_SHIFT		1
 #define   GS_BOOTROM_MASK		  (0x7F << GS_BOOTROM_SHIFT)
 #define   GS_BOOTROM_RSA_FAILED		  (0x50 << GS_BOOTROM_SHIFT)
+#define   GS_BOOTROM_JUMP_PASSED	  (0x76 << GS_BOOTROM_SHIFT)
 #define   GS_UKERNEL_SHIFT		8
 #define   GS_UKERNEL_MASK		  (0xFF << GS_UKERNEL_SHIFT)
 #define   GS_UKERNEL_LAPIC_DONE		  (0x30 << GS_UKERNEL_SHIFT)
@@ -38,7 +40,13 @@
 #define   GS_UKERNEL_READY		  (0xF0 << GS_UKERNEL_SHIFT)
 #define   GS_MIA_SHIFT			16
 #define   GS_MIA_MASK			  (0x07 << GS_MIA_SHIFT)
-#define   GS_MIA_CORE_STATE		  (1 << GS_MIA_SHIFT)
+#define   GS_MIA_CORE_STATE		  (0x01 << GS_MIA_SHIFT)
+#define   GS_MIA_HALT_REQUESTED		  (0x02 << GS_MIA_SHIFT)
+#define   GS_MIA_ISR_ENTRY		  (0x04 << GS_MIA_SHIFT)
+#define   GS_AUTH_STATUS_SHIFT		30
+#define   GS_AUTH_STATUS_MASK		  (0x03 << GS_AUTH_STATUS_SHIFT)
+#define   GS_AUTH_STATUS_BAD		  (0x01 << GS_AUTH_STATUS_SHIFT)
+#define   GS_AUTH_STATUS_GOOD		  (0x02 << GS_AUTH_STATUS_SHIFT)
 
 #define SOFT_SCRATCH(n)			_MMIO(0xc180 + (n) * 4)
 #define SOFT_SCRATCH_COUNT		16

drivers/gpu/drm/i915/intel_guc_loader.c

@@ -387,7 +387,7 @@ int intel_guc_ucode_load(struct drm_device *dev)
 {
 	struct drm_i915_private *dev_priv = dev->dev_private;
 	struct intel_guc_fw *guc_fw = &dev_priv->guc.guc_fw;
-	int err = 0;
+	int retries, err = 0;
 
 	if (!i915.enable_guc_submission)
 		return 0;
@@ -441,29 +441,26 @@ int intel_guc_ucode_load(struct drm_device *dev)
 	 * steppings also so this is extended as well.
 	 */
 	/* WaEnableGuCBootHashCheckNotSet:skl,bxt */
-	err = guc_ucode_xfer(dev_priv);
-	if (err) {
-		int retries = 3;
-
-		DRM_ERROR("GuC fw load failed, err=%d, attempting reset and retry\n", err);
-
-		while (retries--) {
+	for (retries = 3; ; ) {
+		/*
+		 * Always reset the GuC just before (re)loading, so
+		 * that the state and timing are fairly predictable
+		 */
 		err = i915_reset_guc(dev_priv);
-			if (err)
-				break;
+		if (err) {
+			DRM_ERROR("GuC reset failed, err %d\n", err);
+			goto fail;
+		}
 
 		err = guc_ucode_xfer(dev_priv);
-			if (!err) {
-				DRM_DEBUG_DRIVER("GuC fw reload succeeded after reset\n");
+		if (!err)
 			break;
-			}
-			DRM_DEBUG_DRIVER("GuC fw reload retries left: %d\n", retries);
-		}
 
-		if (err) {
-			DRM_ERROR("GuC fw reload attempt failed, ret=%d\n", err);
+		if (--retries == 0)
 			goto fail;
-		}
+
+		DRM_INFO("GuC fw load failed, err %d; will reset and "
+			"retry %d more time(s)\n", err, retries);
 	}
 
 	guc_fw->guc_fw_load_status = GUC_FIRMWARE_SUCCESS;
@@ -485,6 +482,7 @@ int intel_guc_ucode_load(struct drm_device *dev)
 	return 0;
 
 fail:
+	DRM_ERROR("GuC firmware load failed, err %d\n", err);
 	if (guc_fw->guc_fw_load_status == GUC_FIRMWARE_PENDING)
 		guc_fw->guc_fw_load_status = GUC_FIRMWARE_FAIL;