Commit decf67aa authored by Stephen Hemminger's avatar Stephen Hemminger Committed by Jeff Garzik

[PATCH] sk98lin: error handling on dual port board

Sk98lin driver error recovery on two port boards is bad.
If it fails the second allocation, it will not release resources
properly. Also it registers the second port in the pci driver data

If second port fails, might as well go with one port.
Signed-off-by: default avatarStephen Hemminger <shemminger@osdl.org>
Signed-off-by: default avatarJeff Garzik <jgarzik@pobox.com>
parent bce7c95e
......@@ -4899,15 +4899,17 @@ static int __devinit skge_probe_one(struct pci_dev *pdev,
boards_found++;
pci_set_drvdata(pdev, dev);
/* More then one port found */
if ((pAC->GIni.GIMacsFound == 2 ) && (pAC->RlmtNets == 2)) {
if ((dev = alloc_etherdev(sizeof(DEV_NET))) == 0) {
printk(KERN_ERR "Unable to allocate etherdev "
dev = alloc_etherdev(sizeof(DEV_NET));
if (!dev) {
printk(KERN_ERR "sk98lin: unable to allocate etherdev "
"structure!\n");
goto out;
goto single_port;
}
pAC->dev[1] = dev;
pNet = netdev_priv(dev);
pNet->PortNr = 1;
pNet->NetNr = 1;
......@@ -4939,11 +4941,15 @@ static int __devinit skge_probe_one(struct pci_dev *pdev,
if (using_dac)
dev->features |= NETIF_F_HIGHDMA;
if (register_netdev(dev)) {
printk(KERN_ERR "sk98lin: Could not register device for seconf port.\n");
error = register_netdev(dev);
if (error) {
printk(KERN_ERR "sk98lin: Could not register device"
" for second port. (%d)\n", error);
free_netdev(dev);
pAC->dev[1] = pAC->dev[0];
} else {
goto single_port;
}
pAC->dev[1] = dev;
memcpy(&dev->dev_addr,
&pAC->Addr.Net[1].CurrentMacAddress, 6);
memcpy(dev->perm_addr, dev->dev_addr, dev->addr_len);
......@@ -4951,7 +4957,8 @@ static int __devinit skge_probe_one(struct pci_dev *pdev,
printk("%s: %s\n", dev->name, DeviceStr);
printk(" PrefPort:B RlmtMode:Dual Check Link State\n");
}
}
single_port:
/* Save the hardware revision */
pAC->HWRevision = (((pAC->GIni.GIPciHwRev >> 4) & 0x0F)*10) +
......@@ -4964,7 +4971,6 @@ static int __devinit skge_probe_one(struct pci_dev *pdev,
memset(&pAC->PnmiBackup, 0, sizeof(SK_PNMI_STRUCT_DATA));
memcpy(&pAC->PnmiBackup, &pAC->PnmiStruct, sizeof(SK_PNMI_STRUCT_DATA));
pci_set_drvdata(pdev, dev);
return 0;
out_free_resources:
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment