Merge bk://bk.arm.linux.org.uk

into home.transmeta.com:/home/torvalds/v2.5/linux

Documentation/arm/XScale/ADIFCC/80200EVB

+
+Board Overview
+-----------------------------
+
+This is an beta release of the Xscale Linux port to the ADI 80200EVB
+evaluation board.
+
+The 80200EVB is an evaluation platform for ADI Engineering's high-performance
+80200FCC chipset for the Intel 80200 XScale CPU. The 80200FCC is an open
+source FPGA based system that contains a PCI unit and a high performance
+memory controller.
+
+In addition to the 80200FCC, the board also contains a 16C550 UART, and 4MB
+of flash.
+
+The board is still under development and currently only the UART is functional
+as the PCI bits have not been programmed into the FPGA.
+
+For more information on the board, see http://www.adiengineering.com
+
+Port Status
+-----------------------------
+
+Supported:
+
+- Onboard UART (Polled operation only)
+- Cache/TLB locking on 80200 CPU
+
+TODO:
+
+- PCI when hardware supports it
+
+Building the Kernel
+-----------------------------
+change Linux makefile
+make adi_evb_config
+make oldconfig
+make dep
+make zImage
+
+Loading Linux
+-----------------------------
+
+Before you can use Linux on the ADI board, you need to grab the following:
+
+ADI 80200EVB Monitor:
+	ftp://source.mvista.com/pub/xscale/ADI_EVB/monitor.srec
+
+ADI JFFS2 Image:
+	ftp://source.mvista.com/pub/xscale/ADI_EVB/adi.jffs2
+
+Once you've got the Cygnus prompt, type in the following command:
+
+	load
+
+On another terminal window:
+
+	cat monitor.srec > /dev/ttyS0
+
+(replace ttyS0 with the serial port you are using)
+
+Once completed, just type 'go' at the cygmon prompt and you should see:
+
+	MontaVista IQ80310 Monitor Version 0.1
+	monitor>
+
+Type 'b 115200' at the prompt and change your terminal speed to 115200
+
+The first thing to do is to upload and burn the jffs2 filesystem image
+onto the boards 4MB of flash:
+
+	monitor> u c1000000
+	Uploading file at 0xc1000000
+	Now send file with ymodem
+
+Do as the monitor says and transfer the file adi.jffs2.  Once complete,
+the following will copy the jffs2 image to location 0x80000 in the flash.
+
+	monitor> f 8000 c1000000 200000
+	Erasing sector 0x00080000
+	Writing sector 0x00080000 with data at 0xC1000000
+	Erasing sector 0x000A0000
+	Writing sector 0x000A0000 with data at 0xC1020000
+	Erasing sector 0x000C0000
+	...
+
+Now use the same command as above to upload your zImage to location c1000000.
+When you've done that, type 'j c1000000' to run Linux.  Login as
+root and you're all set to go.
+
+Misc Notes
+-----------------------------
+
+The current version of the HW does not have an onboard timer, so the 80200
+PMU is not available for general use as it is being used for a timer source.
+
+By default, the MTD driver reserves the first 512K for bootloaders and
+the remaining 3.5MB for the filesystem. You can edit drivers/mtd/map/adi_evb.c
+to change this as needed for your application.
+
+Contributors
+-----------------------------
+
+Thanks to ADI Engineering for providing the hardware for development
+
+Deepak Saxena <dsaxena@mvista.com> - Initial port
+
+-----------------------------
+Enjoy.  If you have any problem please contact Deepak Saxena
+dsaxena@mvista.com
+

arch/arm/Makefile

@@ -8,6 +8,7 @@
 # Copyright (C) 1995-2001 by Russell King
 
 LDFLAGS_vmlinux	:=-p -X
+AFLAGS_vmlinux.lds.o = -DTEXTADDR=$(TEXTADDR) -DDATAADDR=$(DATAADDR)
 OBJCOPYFLAGS	:=-O binary -R .note -R .comment -S
 GZFLAGS		:=-9
 #CFLAGS		+=-pipe
@@ -50,18 +51,29 @@ tune-$(CONFIG_CPU_SA110)	:=-mtune=strongarm110
 tune-$(CONFIG_CPU_SA1100)	:=-mtune=strongarm1100
 tune-$(CONFIG_CPU_XSCALE)	:=-mtune=strongarm #-mtune=xscale
 
-CFLAGS_BOOT	:=$(apcs-y) $(arch-y) $(tune-y) -mshort-load-bytes -msoft-float
-CFLAGS		+=$(apcs-y) $(arch-y) $(tune-y) -mshort-load-bytes -msoft-float
-AFLAGS		+=$(apcs-y) $(arch-y) -mno-fpu -msoft-float
+# Force -mno-fpu to be passed to the assembler.  Some versions of gcc don't
+# do this with -msoft-float
+CFLAGS_BOOT	:=$(apcs-y) $(arch-y) $(tune-y) -mshort-load-bytes -msoft-float -Wa,-mno-fpu
+CFLAGS		+=$(apcs-y) $(arch-y) $(tune-y) -mshort-load-bytes -msoft-float -Wa,-mno-fpu
+AFLAGS		+=$(apcs-y) $(arch-y) -mno-fpu -msoft-float -Wa,-mno-fpu
 
 ifeq ($(CONFIG_CPU_26),y)
 PROCESSOR	:= armo
 HEAD		:= arch/arm/mach-arc/head.o arch/arm/kernel/init_task.o
+  ifeq ($(CONFIG_ROM_KERNEL),y)
+    DATAADDR	 = 0x02080000
+    TEXTADDR	 = 0x03800000
+    LDSCRIPT	 = arch/arm/vmlinux-armo-rom.lds.in
+  else
+    TEXTADDR	 = 0x02080000
+    LDSCRIPT	 = arch/arm/vmlinux-armo.lds.in
+  endif
 endif
 
 ifeq ($(CONFIG_CPU_32),y)
 PROCESSOR	 = armv
 HEAD		:= arch/arm/kernel/head.o arch/arm/kernel/init_task.o
+TEXTADDR	 = 0xC0008000
 endif
 
 ifeq ($(CONFIG_ARCH_ARCA5K),y)
@@ -175,7 +187,7 @@ core-$(CONFIG_FPE_NWFPE)	+= arch/arm/nwfpe/
 core-$(CONFIG_FPE_FASTFPE)	+= $(FASTFPE_OBJ)
 
 drivers-$(CONFIG_ARCH_CLPS7500)	+= drivers/acorn/char/
-drivers-$(CONFIG_ARCH_L7200))	+= drivers/acorn/char/
+drivers-$(CONFIG_ARCH_L7200)	+= drivers/acorn/char/
 
 libs-y				+= arch/arm/lib/
 

arch/arm/boot/compressed/Makefile

@@ -18,7 +18,7 @@ ZLDFLAGS	 = -p -X -T vmlinux.lds
 #
 ifeq ($(CONFIG_ARCH_ACORN),y)
 OBJS		+= ll_char_wr.o font.o
-ZLDFLAGS	+= -defsym params=$(PARAMS_PHYS)
+CFLAGS		+= -DPARAMS_PHYS=$(PARAMS_PHYS)
 endif
 
 ifeq ($(CONFIG_ARCH_NETWINDER),y)

arch/arm/boot/compressed/head.S

@@ -55,6 +55,18 @@
 		.macro	writeb, rb
 		strb	\rb, [r3, #0]
 		.endm
+#elif defined(CONFIG_ARCH_SA1100)
+		.macro	loadsp, rb
+		mov	\rb, #0x80000000	@ physical base address
+#  if defined(CONFIG_DEBUG_LL_SER3)
+		add	\rb, \rb, #0x00050000	@ Ser3
+#  else
+		add	\rb, \rb, #0x00010000	@ Ser1
+#  endif
+		.endm
+		.macro	writeb, rb
+		str	\rb, [r3, #0x14]	@ UTDR
+		.endm
 #else
 #error no serial architecture defined
 #endif
@@ -151,22 +163,55 @@ not_angel:
 		ldmia	r0, {r1, r2, r3, r4, r5, r6, ip, sp}
 		subs	r0, r0, r1		@ calculate the delta offset
 
-		teq	r0, #0			@ if delta is zero, we're
+						@ if delta is zero, we're
 		beq	not_relocated		@ running at the address we
 						@ were linked at.
 
-		add	r2, r2, r0		@ different address, so we
-		add	r3, r3, r0		@ need to fix up various
-		add	r5, r5, r0		@ pointers.
+		/*
+		 * We're running at a different address.  We need to fix
+		 * up various pointers:
+		 *   r5 - zImage base address
+		 *   r6 - GOT start
+		 *   ip - GOT end
+		 */
+		add	r5, r5, r0
 		add	r6, r6, r0
 		add	ip, ip, r0
+
+#ifndef CONFIG_ZBOOT_ROM
+		/*
+		 * If we're running fully PIC === CONFIG_ZBOOT_ROM = n,
+		 * we need to fix up pointers into the BSS region.
+		 *   r2 - BSS start
+		 *   r3 - BSS end
+		 *   sp - stack pointer
+		 */
+		add	r2, r2, r0
+		add	r3, r3, r0
 		add	sp, sp, r0
 
+		/*
+		 * Relocate all entries in the GOT table.
+		 */
 1:		ldr	r1, [r6, #0]		@ relocate entries in the GOT
 		add	r1, r1, r0		@ table.  This fixes up the
 		str	r1, [r6], #4		@ C references.
 		cmp	r6, ip
 		blo	1b
+#else
+
+		/*
+		 * Relocate entries in the GOT table.  We only relocate
+		 * the entries that are outside the (relocated) BSS region.
+		 */
+1:		ldr	r1, [r6, #0]		@ relocate entries in the GOT
+		cmp	r1, r2			@ entry < bss_start ||
+		cmphs	r3, r1			@ _end < entry
+		addlo	r1, r1, r0		@ table.  This fixes up the
+		str	r1, [r6], #4		@ C references.
+		cmp	r6, ip
+		blo	1b
+#endif
 
 not_relocated:	mov	r0, #0
 1:		str	r0, [r2], #4		@ clear bss
@@ -176,6 +221,11 @@ not_relocated:	mov	r0, #0
 		cmp	r2, r3
 		blo	1b
 
+		/*
+		 * The C runtime environment should now be setup
+		 * sufficiently.  Turn the cache on, set up some
+		 * pointers, and start decompressing.
+		 */
 		bl	cache_on
 
 		mov	r1, sp			@ malloc space above stack

arch/arm/boot/compressed/ll_char_wr.S

@@ -21,78 +21,59 @@
 #include <asm/assembler.h>
 	.text
 
-#define BOLD            0x01
-#define ITALIC          0x02
-#define UNDERLINE       0x04
-#define FLASH           0x08
-#define INVERSE         0x10
-
-LC0:		.word	bytes_per_char_h
+LC0:	.word	LC0
+	.word	bytes_per_char_h
 	.word	video_size_row
 	.word	acorndata_8x8
 	.word	con_charconvtable
 
+/*
+ * r0 = ptr
+ * r1 = char
+ * r2 = white
+ */
 ENTRY(ll_write_char)
 	stmfd	sp!, {r4 - r7, lr}
 @
 @ Smashable regs: {r0 - r3}, [r4 - r7], (r8 - fp), [ip], (sp), [lr], (pc)
 @
-		eor	ip, r1, #UNDERLINE << 9
-/*
- * calculate colours
- */
-		tst	r1, #INVERSE << 9
-		moveq	r2, r1, lsr #16
-		moveq	r3, r1, lsr #24
-		movne	r2, r1, lsr #24
-		movne	r3, r1, lsr #16
-		and	r3, r3, #255
-		and	r2, r2, #255
-/*
+	/*
 	 * calculate offset into character table
 	 */
-		mov	r1, r1, lsl #23
-		mov	r1, r1, lsr #20
-/*
- * calculate offset required for each row [maybe I should make this an argument to this fn.
- * Have to see what the register usage is like in the calling routines.
+	mov	r1, r1, lsl #3
+	/*
+	 * calculate offset required for each row.
 	 */
-		adr	r4, LC0
-		ldmia	r4, {r4, r5, r6, lr}
-		ldr	r4, [r4]
-		ldr	r5, [r5]
-/*
+	adr	ip, LC0
+	ldmia	ip, {r3, r4, r5, r6, lr}
+	sub	ip, ip, r3
+	add	r6, r6, ip
+	add	lr, lr, ip
+	ldr	r4, [r4, ip]
+	ldr	r5, [r5, ip]
+	/*
 	 * Go to resolution-dependent routine...
 	 */
 	cmp	r4, #4
 	blt	Lrow1bpp
-		eor	r2, r3, r2			@ Create eor mask to change colour from bg
-		orr	r3, r3, r3, lsl #8		@ to fg.
-		orr	r3, r3, r3, lsl #16
 	add	r0, r0, r5, lsl #3		@ Move to bottom of character
-		add	r1, r1, #7
+	orr	r1, r1, #7
 	ldrb	r7, [r6, r1]
-		tst	ip, #UNDERLINE << 9
-		eoreq	r7, r7, #255
 	teq	r4, #8
 	beq	Lrow8bpplp
 @
 @ Smashable regs: {r0 - r3}, [r4], {r5 - r7}, (r8 - fp), [ip], (sp), {lr}, (pc)
 @
-		orr	r3, r3, r3, lsl #4
-Lrow4bpplp:	ldr	r7, [lr, r7, lsl #2]
+Lrow4bpplp:
+	ldr	r7, [lr, r7, lsl #2]
 	mul	r7, r2, r7
-		tst	r1, #7				@ avoid using r7 directly after
-		eor	ip, r3, r7
-		str	ip, [r0, -r5]!
-		LOADREGS(eqfd, sp!, {r4 - r7, pc})
-		sub	r1, r1, #1
+	sub	r1, r1, #1			@ avoid using r7 directly after
+	str	r7, [r0, -r5]!
 	ldrb	r7, [r6, r1]
 	ldr	r7, [lr, r7, lsl #2]
 	mul	r7, r2, r7
 	tst	r1, #7				@ avoid using r7 directly after
-		eor	ip, r3, r7
-		str	ip, [r0, -r5]!
+	str	r7, [r0, -r5]!
 	subne	r1, r1, #1
 	ldrneb	r7, [r6, r1]
 	bne	Lrow4bpplp
@@ -101,19 +82,16 @@ Lrow4bpplp:	ldr	r7, [lr, r7, lsl #2]
 @
 @ Smashable regs: {r0 - r3}, [r4], {r5 - r7}, (r8 - fp), [ip], (sp), {lr}, (pc)
 @
-Lrow8bpplp:	mov	ip, r7, lsr #4
+Lrow8bpplp:
+	mov	ip, r7, lsr #4
 	ldr	ip, [lr, ip, lsl #2]
 	mul	r4, r2, ip
 	and	ip, r7, #15			@ avoid r4
 	ldr	ip, [lr, ip, lsl #2]		@ avoid r4
 	mul	ip, r2, ip			@ avoid r4
-		eor	r4, r3, r4			@ avoid ip
-		tst	r1, #7				@ avoid ip
+	sub	r1, r1, #1			@ avoid ip
 	sub	r0, r0, r5			@ avoid ip
-		eor	ip, r3, ip
 	stmia	r0, {r4, ip}
-		LOADREGS(eqfd, sp!, {r4 - r7, pc})
-		sub	r1, r1, #1
 	ldrb	r7, [r6, r1]
 	mov	ip, r7, lsr #4
 	ldr	ip, [lr, ip, lsl #2]
@@ -121,10 +99,8 @@ Lrow8bpplp:	mov	ip, r7, lsr #4
 	and	ip, r7, #15			@ avoid r4
 	ldr	ip, [lr, ip, lsl #2]		@ avoid r4
 	mul	ip, r2, ip			@ avoid r4
-		eor	r4, r3, r4			@ avoid ip
 	tst	r1, #7				@ avoid ip
 	sub	r0, r0, r5			@ avoid ip
-		eor	ip, r3, ip
 	stmia	r0, {r4, ip}
 	subne	r1, r1, #1
 	ldrneb	r7, [r6, r1]
@@ -134,11 +110,9 @@ Lrow8bpplp:	mov	ip, r7, lsr #4
 @
 @ Smashable regs: {r0 - r3}, [r4], {r5, r6}, [r7], (r8 - fp), [ip], (sp), [lr], (pc)
 @
-Lrow1bpp:	add	r6, r6, r1
+Lrow1bpp:
+	add	r6, r6, r1
 	ldmia	r6, {r4, r7}
-		tst	ip, #INVERSE << 9
-		mvnne	r4, r4
-		mvnne	r7, r7
 	strb	r4, [r0], r5
 	mov	r4, r4, lsr #8
 	strb	r4, [r0], r5
@@ -152,8 +126,6 @@ Lrow1bpp:	add	r6, r6, r1
 	mov	r7, r7, lsr #8
 	strb	r7, [r0], r5
 	mov	r7, r7, lsr #8
-		tst	ip, #UNDERLINE << 9
-		mvneq	r7, r7
 	strb	r7, [r0], r5
 	LOADREGS(fd, sp!, {r4 - r7, pc})
 

arch/arm/config.in

@@ -94,6 +94,8 @@ if [ "$CONFIG_ASSABET_NEPONSET" = "y" -o \
      "$CONFIG_SA1100_XP860" = "y" ]; then
    define_bool CONFIG_SA1111 y
    define_int CONFIG_FORCE_MAX_ZONEORDER 9
+else
+   define_bool CONFIG_SA1111 n
 fi
 
 comment 'Processor Type'
@@ -231,6 +233,8 @@ if [ "$CONFIG_CPU_ARM720T" = "y" -o "$CONFIG_CPU_ARM920T" = "y" -o \
      "$CONFIG_CPU_ARM922T" = "y" -o "$CONFIG_CPU_ARM926T" = "y" -o \
      "$CONFIG_CPU_ARM1020" = "y" -o "$CONFIG_CPU_XSCALE" = "y" ]; then
    dep_bool 'Support Thumb instructions (EXPERIMENTAL)' CONFIG_ARM_THUMB $CONFIG_EXPERIMENTAL
+else
+   define_bool CONFIG_ARM_THUMB n
 fi
 if [ "$CONFIG_CPU_ARM920T" = "y" -o "$CONFIG_CPU_ARM922T" = "y" -o \
      "$CONFIG_CPU_ARM926T" = "y" -o "$CONFIG_CPU_ARM1020" = "y" ]; then

arch/arm/kernel/arch.c

@@ -8,6 +8,7 @@
 #include <linux/types.h>
 
 #include <asm/elf.h>
+#include <asm/page.h>
 #include <asm/setup.h>
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>

arch/arm/kernel/bios32.c

@@ -599,7 +599,7 @@ void pcibios_align_resource(void *data, struct resource *res,
  * pcibios_enable_device - Enable I/O and memory.
  * @dev: PCI device to be enabled
  */
-int pcibios_enable_device(struct pci_dev *dev)
+int pcibios_enable_device(struct pci_dev *dev, int mask)
 {
 	u16 cmd, old_cmd;
 	int idx;
@@ -608,6 +608,10 @@ int pcibios_enable_device(struct pci_dev *dev)
 	pci_read_config_word(dev, PCI_COMMAND, &cmd);
 	old_cmd = cmd;
 	for (idx = 0; idx < 6; idx++) {
+		/* Only set up the requested stuff */
+		if (!(mask & (1 << idx)))
+			continue;
+
 		r = dev->resource + idx;
 		if (!r->start && r->end) {
 			printk(KERN_ERR "PCI: Device %s not available because"
@@ -626,3 +630,29 @@ int pcibios_enable_device(struct pci_dev *dev)
 	}
 	return 0;
 }
+
+int pci_mmap_page_range(struct pci_dev *dev, struct vm_area_struct *vma,
+			enum pci_mmap_state mmap_state, int write_combine)
+{
+	struct pci_sys_data *root = dev->sysdata;
+	unsigned long prot, phys;
+
+	if (mmap_state == pci_mmap_io) {
+		return -EINVAL;
+	} else {
+		phys = root->mem_offset + (vma->vm_pgoff << PAGE_SHIFT);
+	}
+
+	/*
+	 * Mark this as IO
+	 */
+	vma->vm_flags |= VM_SHM | VM_LOCKED | VM_IO;
+	vma->vm_page_prot = pgprot_noncached(vma->vm_page_prot);
+
+	if (remap_page_range(vma, vma->vm_start, phys,
+			     vma->vm_end - vma->vm_start,
+			     vma->vm_page_prot))
+		return -EAGAIN;
+
+	return 0;
+}

arch/arm/kernel/ecard.c

@@ -38,6 +38,7 @@
 #include <linux/slab.h>
 #include <linux/proc_fs.h>
 #include <linux/notifier.h>
+#include <linux/device.h>
 #include <linux/init.h>
 
 #include <asm/dma.h>
@@ -48,6 +49,7 @@
 #include <asm/pgalloc.h>
 #include <asm/mmu_context.h>
 #include <asm/mach/irq.h>
+#include <asm/tlbflush.h>
 
 #ifndef CONFIG_ARCH_RPC
 #define HAVE_EXPMASK
@@ -92,6 +94,8 @@ ecard_loader_reset(volatile unsigned char *pa, loader_t loader);
 asmlinkage extern int
 ecard_loader_read(int off, volatile unsigned char *pa, loader_t loader);
 
+static const struct ecard_id *
+ecard_match_device(const struct ecard_id *ids, struct expansion_card *ec);
 
 static inline unsigned short
 ecard_getu16(unsigned char *v)
@@ -969,6 +973,14 @@ ecard_probe(int slot, card_type_t type)
 
 	*ecp = ec;
 	slot_to_expcard[slot] = ec;
+
+	snprintf(ec->dev.bus_id, sizeof(ec->dev.bus_id), "ecard%d", slot);
+	strcpy(ec->dev.name, "fixme!");
+	ec->dev.parent = NULL;
+	ec->dev.bus    = &ecard_bus_type;
+
+	device_register(&ec->dev);
+
 	return 0;
 
 nodev:
@@ -995,22 +1007,17 @@ ecard_t *ecard_find(int cid, const card_ids *cids)
 		if (finding_pos->claimed)
 			continue;
 
+		if (finding_pos->dev.driver)
+			continue;
+
 		if (!cids) {
 			if ((finding_pos->cid.id ^ cid) == 0)
 				break;
 		} else {
-			unsigned int manufacturer, product;
-			int i;
-
-			manufacturer = finding_pos->cid.manufacturer;
-			product = finding_pos->cid.product;
+			const struct ecard_id *id;
 
-			for (i = 0; cids[i].manufacturer != 65535; i++)
-				if (manufacturer == cids[i].manufacturer &&
-				    product == cids[i].product)
-					break;
-
-			if (cids[i].manufacturer != 65535)
+			id = ecard_match_device(cids, finding_pos);
+			if (id)
 				break;
 		}
 	}
@@ -1023,7 +1030,7 @@ ecard_t *ecard_find(int cid, const card_ids *cids)
  * Locate all hardware - interrupt management and
  * actual cards.
  */
-void __init ecard_init(void)
+static int __init ecard_init(void)
 {
 	int slot, irqhw;
 
@@ -1053,11 +1060,96 @@ void __init ecard_init(void)
 				irqhw ? ecard_irqexp_handler : ecard_irq_handler);
 
 	ecard_proc_init();
+
+	return 0;
 }
 
 subsys_initcall(ecard_init);
 
+/*
+ *	ECARD "bus"
+ */
+static const struct ecard_id *
+ecard_match_device(const struct ecard_id *ids, struct expansion_card *ec)
+{
+	int i;
+
+	for (i = 0; ids[i].manufacturer != 65535; i++)
+		if (ec->cid.manufacturer == ids[i].manufacturer &&
+		    ec->cid.product == ids[i].product)
+			return ids + i;
+
+	return NULL;
+}
+
+static int ecard_drv_probe(struct device *dev)
+{
+	struct expansion_card *ec = ECARD_DEV(dev);
+	struct ecard_driver *drv = ECARD_DRV(dev->driver);
+	const struct ecard_id *id;
+
+	id = ecard_match_device(drv->id_table, ec);
+
+	return drv->probe(ec, id);
+}
+
+static int ecard_drv_remove(struct device *dev)
+{
+	struct expansion_card *ec = ECARD_DEV(dev);
+	struct ecard_driver *drv = ECARD_DRV(dev->driver);
+
+	drv->remove(ec);
+
+	return 0;
+}
+
+int ecard_register_driver(struct ecard_driver *drv)
+{
+	drv->drv.bus = &ecard_bus_type;
+	drv->drv.probe = ecard_drv_probe;
+	drv->drv.remove = ecard_drv_remove;
+
+	return driver_register(&drv->drv);
+}
+
+void ecard_remove_driver(struct ecard_driver *drv)
+{
+	remove_driver(&drv->drv);
+}
+
+static int ecard_match(struct device *_dev, struct device_driver *_drv)
+{
+	struct expansion_card *ec = ECARD_DEV(_dev);
+	struct ecard_driver *drv = ECARD_DRV(_drv);
+	int ret;
+
+	if (drv->id_table) {
+		ret = ecard_match_device(drv->id_table, ec) != NULL;
+	} else {
+		ret = ec->cid.id == drv->id;
+	}
+
+	return ret;
+}
+
+struct bus_type ecard_bus_type = {
+	.name	= "ecard",
+	.match	= ecard_match,
+};
+
+static int ecard_bus_init(void)
+{
+	return bus_register(&ecard_bus_type);
+}
+
+postcore_initcall(ecard_bus_init);
+
 EXPORT_SYMBOL(ecard_startfind);
 EXPORT_SYMBOL(ecard_find);
 EXPORT_SYMBOL(ecard_readchunk);
 EXPORT_SYMBOL(ecard_address);
+
+EXPORT_SYMBOL(ecard_register_driver);
+EXPORT_SYMBOL(ecard_remove_driver);
+
+EXPORT_SYMBOL(ecard_bus_type);

arch/arm/kernel/entry-armv.S

@@ -189,11 +189,10 @@ irq_prio_ld:	.byte	40,40,41,40,42,42,42,42,43,43,43,43,43,43,43,43
 
 		.macro	get_irqnr_and_base, irqnr, irqstat, base, tmp
 		mov	r4, #0xe0000000
-		orr	r4, r4, #0x20
 
 		mov	\irqstat, #0x0C
-		strb	\irqstat, [r4]			@outb(0x0C, 0x20) /* Poll command */
-		ldrb	\irqnr, [r4]			@irq = inb(0x20) & 7
+		strb	\irqstat, [r4, #0x20]		@outb(0x0C, 0x20) /* Poll command */
+		ldrb	\irqnr, [r4, #0x10]		@irq = inb(0x20) & 7
 		and	\irqstat, \irqnr, #0x80
 		teq	\irqstat, #0
 		beq	43f
@@ -201,8 +200,8 @@ irq_prio_ld:	.byte	40,40,41,40,42,42,42,42,43,43,43,43,43,43,43,43
 		teq	\irqnr, #2
 		bne	44f
 43:		mov	\irqstat, #0x0C
-		strb	\irqstat, [r4, #0x80]		@outb(0x0C, 0xA0) /* Poll command */
-		ldrb	\irqnr, [r4, #0x80]		@irq = (inb(0xA0) & 7) + 8
+		strb	\irqstat, [r4, #0xa0]		@outb(0x0C, 0xA0) /* Poll command */
+		ldrb	\irqnr, [r4, #0xa0]		@irq = (inb(0xA0) & 7) + 8
 		and	\irqstat, \irqnr, #0x80
 		teq	\irqstat, #0
 		beq	44f
@@ -655,7 +654,7 @@ __und_invalid:	sub	sp, sp, #S_FRAME_SIZE
 		and	r2, r6, #31			@ int mode
 		b	bad_mode
 
-#if defined CONFIG_FPE_NWFPE || defined CONFIG_FPE_FASTFPE
+#if 1 /* defined CONFIG_FPE_NWFPE || defined CONFIG_FPE_FASTFPE */
 		/* The FPE is always present */
 		.equ	fpe_not_present, fpundefinstr
 #else
@@ -766,6 +765,8 @@ preempt_return:
 		msr	spsr, r0
 		ldmia	sp, {r0 - pc}^			@ load r0 - pc, cpsr
 
+		.ltorg
+
 #ifdef CONFIG_PREEMPT
 svc_preempt:	teq	r9, #0				@ was preempt count = 0
 		ldreq	r6, .LCirq_stat
@@ -902,6 +903,8 @@ __irq_usr:	sub	sp, sp, #S_FRAME_SIZE
 		mov	why, #0
 		b	ret_to_user
 
+		.ltorg
+
 		.align	5
 __und_usr:	sub	sp, sp, #S_FRAME_SIZE		@ Allocate frame size in one go
 		stmia	sp, {r0 - r12}			@ Save r0 - r12

arch/arm/kernel/process.c

@@ -367,8 +367,8 @@ void dump_thread(struct pt_regs * regs, struct user * dump)
 
 	dump->u_debugreg[0] = tsk->thread.debug.bp[0].address;
 	dump->u_debugreg[1] = tsk->thread.debug.bp[1].address;
-	dump->u_debugreg[2] = tsk->thread.debug.bp[0].insn;
-	dump->u_debugreg[3] = tsk->thread.debug.bp[1].insn;
+	dump->u_debugreg[2] = tsk->thread.debug.bp[0].insn.arm;
+	dump->u_debugreg[3] = tsk->thread.debug.bp[1].insn.arm;
 	dump->u_debugreg[4] = tsk->thread.debug.nsaved;
 
 	if (dump->start_stack < 0x04000000)

arch/arm/kernel/ptrace.c

@@ -32,10 +32,24 @@
  * in exit.c or in signal.c.
  */
 
+#if 1
 /*
  * Breakpoint SWI instruction: SWI &9F0001
  */
 #define BREAKINST_ARM	0xef9f0001
+#define BREAKINST_THUMB	0xdf00		/* fill this in later */
+#else
+/*
+ * New breakpoints - use an undefined instruction.  The ARM architecture
+ * reference manual guarantees that the following instruction space
+ * will produce an undefined instruction exception on all CPUs:
+ *
+ *  ARM:   xxxx 0111 1111 xxxx xxxx xxxx 1111 xxxx
+ *  Thumb: 1101 1110 xxxx xxxx
+ */
+#define BREAKINST_ARM	0xe7f001f0
+#define BREAKINST_THUMB	0xde01
+#endif
 
 /*
  * Get the address of the live pt_regs for the specified task.
@@ -89,23 +103,32 @@ put_user_reg(struct task_struct *task, int offset, long data)
 }
 
 static inline int
-read_tsk_long(struct task_struct *child, unsigned long addr, unsigned long *res)
+read_u32(struct task_struct *task, unsigned long addr, u32 *res)
 {
-	int copied;
+	int ret;
 
-	copied = access_process_vm(child, addr, res, sizeof(*res), 0);
+	ret = access_process_vm(task, addr, res, sizeof(*res), 0);
 
-	return copied != sizeof(*res) ? -EIO : 0;
+	return ret == sizeof(*res) ? 0 : -EIO;
 }
 
 static inline int
-write_tsk_long(struct task_struct *child, unsigned long addr, unsigned long val)
+read_instr(struct task_struct *task, unsigned long addr, u32 *res)
 {
-	int copied;
-
-	copied = access_process_vm(child, addr, &val, sizeof(val), 1);
+	int ret;
 
-	return copied != sizeof(val) ? -EIO : 0;
+	if (addr & 1) {
+		u16 val;
+		ret = access_process_vm(task, addr & ~1, &val, sizeof(val), 0);
+		ret = ret == sizeof(val) ? 0 : -EIO;
+		*res = val;
+	} else {
+		u32 val;
+		ret = access_process_vm(task, addr & ~3, &val, sizeof(val), 0);
+		ret = ret == sizeof(val) ? 0 : -EIO;
+		*res = val;
+	}
+	return ret;
 }
 
 /*
@@ -206,7 +229,7 @@ ptrace_getldrop2(struct task_struct *child, unsigned long insn)
 static unsigned long
 get_branch_address(struct task_struct *child, unsigned long pc, unsigned long insn)
 {
-	unsigned long alt = 0;
+	u32 alt = 0;
 
 	switch (insn & 0x0e000000) {
 	case 0x00000000:
@@ -262,7 +285,7 @@ get_branch_address(struct task_struct *child, unsigned long pc, unsigned long in
 				else
 					base -= aluop2;
 			}
-			if (read_tsk_long(child, base, &alt) == 0)
+			if (read_u32(child, base, &alt) == 0)
 				alt = pc_pointer(alt);
 		}
 		break;
@@ -289,7 +312,7 @@ get_branch_address(struct task_struct *child, unsigned long pc, unsigned long in
 
 			base = ptrace_getrn(child, insn);
 
-			if (read_tsk_long(child, base + nr_regs, &alt) == 0)
+			if (read_u32(child, base + nr_regs, &alt) == 0)
 				alt = pc_pointer(alt);
 			break;
 		}
@@ -319,30 +342,71 @@ get_branch_address(struct task_struct *child, unsigned long pc, unsigned long in
 }
 
 static int
-add_breakpoint(struct task_struct *child, struct debug_info *dbg, unsigned long addr)
+swap_insn(struct task_struct *task, unsigned long addr,
+	  void *old_insn, void *new_insn, int size)
+{
+	int ret;
+
+	ret = access_process_vm(task, addr, old_insn, size, 0);
+	if (ret == size)
+		ret = access_process_vm(task, addr, new_insn, size, 1);
+	return ret;
+}
+
+static void
+add_breakpoint(struct task_struct *task, struct debug_info *dbg, unsigned long addr)
 {
 	int nr = dbg->nsaved;
-	int res = -EINVAL;
 
 	if (nr < 2) {
-		res = read_tsk_long(child, addr, &dbg->bp[nr].insn);
-		if (res == 0)
-			res = write_tsk_long(child, addr, BREAKINST_ARM);
+		u32 new_insn = BREAKINST_ARM;
+		int res;
+
+		res = swap_insn(task, addr, &dbg->bp[nr].insn, &new_insn, 4);
 
-		if (res == 0) {
+		if (res == 4) {
 			dbg->bp[nr].address = addr;
 			dbg->nsaved += 1;
 		}
 	} else
 		printk(KERN_ERR "ptrace: too many breakpoints\n");
+}
 
-	return res;
+/*
+ * Clear one breakpoint in the user program.  We copy what the hardware
+ * does and use bit 0 of the address to indicate whether this is a Thumb
+ * breakpoint or an ARM breakpoint.
+ */
+static void clear_breakpoint(struct task_struct *task, struct debug_entry *bp)
+{
+	unsigned long addr = bp->address;
+	union debug_insn old_insn;
+	int ret;
+
+	if (addr & 1) {
+		ret = swap_insn(task, addr & ~1, &old_insn.thumb,
+				&bp->insn.thumb, 2);
+
+		if (ret != 2 || old_insn.thumb != BREAKINST_THUMB)
+			printk(KERN_ERR "%s:%d: corrupted Thumb breakpoint at "
+				"0x%08lx (0x%04x)\n", task->comm, task->pid,
+				addr, old_insn.thumb);
+	} else {
+		ret = swap_insn(task, addr & ~3, &old_insn.arm,
+				&bp->insn.arm, 4);
+
+		if (ret != 4 || old_insn.arm != BREAKINST_ARM)
+			printk(KERN_ERR "%s:%d: corrupted ARM breakpoint at "
+				"0x%08lx (0x%08x)\n", task->comm, task->pid,
+				addr, old_insn.arm);
+	}
 }
 
 void ptrace_set_bpt(struct task_struct *child)
 {
 	struct pt_regs *regs;
-	unsigned long pc, insn;
+	unsigned long pc;
+	u32 insn;
 	int res;
 
 	regs = get_user_regs(child);
@@ -353,7 +417,7 @@ void ptrace_set_bpt(struct task_struct *child)
 		return;
 	}
 
-	res = read_tsk_long(child, pc, &insn);
+	res = read_instr(child, pc, &insn);
 	if (!res) {
 		struct debug_info *dbg = &child->thread.debug;
 		unsigned long alt;
@@ -362,7 +426,7 @@ void ptrace_set_bpt(struct task_struct *child)
 
 		alt = get_branch_address(child, pc, insn);
 		if (alt)
-			res = add_breakpoint(child, dbg, alt);
+			add_breakpoint(child, dbg, alt);
 
 		/*
 		 * Note that we ignore the result of setting the above
@@ -374,7 +438,7 @@ void ptrace_set_bpt(struct task_struct *child)
 		 * loose control of the thread during single stepping.
 		 */
 		if (!alt || predicate(insn) != PREDICATE_ALWAYS)
-			res = add_breakpoint(child, dbg, pc + 4);
+			add_breakpoint(child, dbg, pc + 4);
 	}
 }
 
@@ -384,24 +448,17 @@ void ptrace_set_bpt(struct task_struct *child)
  */
 void __ptrace_cancel_bpt(struct task_struct *child)
 {
-	struct debug_info *dbg = &child->thread.debug;
-	int i, nsaved = dbg->nsaved;
+	int i, nsaved = child->thread.debug.nsaved;
 
-	dbg->nsaved = 0;
+	child->thread.debug.nsaved = 0;
 
 	if (nsaved > 2) {
 		printk("ptrace_cancel_bpt: bogus nsaved: %d!\n", nsaved);
 		nsaved = 2;
 	}
 
-	for (i = 0; i < nsaved; i++) {
-		unsigned long tmp;
-
-		read_tsk_long(child, dbg->bp[i].address, &tmp);
-		write_tsk_long(child, dbg->bp[i].address, dbg->bp[i].insn);
-		if (tmp != BREAKINST_ARM)
-			printk(KERN_ERR "ptrace_cancel_bpt: weirdness\n");
-	}
+	for (i = 0; i < nsaved; i++)
+		clear_breakpoint(child, &child->thread.debug.bp[i]);
 }
 
 /*
@@ -537,9 +594,12 @@ static int do_ptrace(int request, struct task_struct *child, long addr, long dat
 		 */
 		case PTRACE_PEEKTEXT:
 		case PTRACE_PEEKDATA:
-			ret = read_tsk_long(child, addr, &tmp);
-			if (!ret)
+			ret = access_process_vm(child, addr, &tmp,
+						sizeof(unsigned long), 0);
+			if (ret == sizeof(unsigned long))
 				ret = put_user(tmp, (unsigned long *) data);
+			else
+				ret = -EIO;
 			break;
 
 		case PTRACE_PEEKUSR:
@@ -551,7 +611,12 @@ static int do_ptrace(int request, struct task_struct *child, long addr, long dat
 		 */
 		case PTRACE_POKETEXT:
 		case PTRACE_POKEDATA:
-			ret = write_tsk_long(child, addr, data);
+			ret = access_process_vm(child, addr, &data,
+						sizeof(unsigned long), 1);
+			if (ret == sizeof(unsigned long))
+				ret = 0;
+			else
+				ret = -EIO;
 			break;
 
 		case PTRACE_POKEUSR:

arch/arm/kernel/setup.c

@@ -193,26 +193,25 @@ static inline void dump_cache(const char *prefix, unsigned int cache)
 			CACHE_LINE(cache)));
 }
 
-static inline void dump_cpu_cache_id(void)
+static void __init dump_cpu_info(void)
 {
-	unsigned int cache_info;
-
-	asm("mrc p15, 0, %0, c0, c0, 1" : "=r" (cache_info));
+	unsigned int info;
 
-	if (cache_info == processor_id)
-		return;
+	asm("mrc p15, 0, %0, c0, c0, 1" : "=r" (info));
 
-	printk("CPU: D %s cache\n", cache_types[CACHE_TYPE(cache_info)]);
-	if (CACHE_S(cache_info)) {
-		dump_cache("CPU: I cache", CACHE_ISIZE(cache_info));
-		dump_cache("CPU: D cache", CACHE_DSIZE(cache_info));
+	if (info != processor_id) {
+		printk("CPU: D %s cache\n", cache_types[CACHE_TYPE(info)]);
+		if (CACHE_S(info)) {
+			dump_cache("CPU: I cache", CACHE_ISIZE(info));
+			dump_cache("CPU: D cache", CACHE_DSIZE(info));
 		} else {
-		dump_cache("CPU: cache", CACHE_ISIZE(cache_info));
+			dump_cache("CPU: cache", CACHE_ISIZE(info));
+		}
 	}
 }
 
 #else
-#define dump_cpu_cache_id() do { } while (0)
+#define dump_cpu_info() do { } while (0)
 #endif
 
 static void __init setup_processor(void)
@@ -255,7 +254,7 @@ static void __init setup_processor(void)
 	       proc_info.manufacturer, proc_info.cpu_name,
 	       (int)processor_id & 15);
 
-	dump_cpu_cache_id();
+	dump_cpu_info();
 
 	sprintf(system_utsname.machine, "%s%c", list->arch_name, ENDIANNESS);
 	sprintf(elf_platform, "%s%c", list->elf_name, ENDIANNESS);

arch/arm/kernel/signal.c

@@ -59,11 +59,11 @@ asmlinkage int sys_sigsuspend(int restart, unsigned long oldmask, old_sigset_t m
 	sigset_t saveset;
 
 	mask &= _BLOCKABLE;
-	spin_lock_irq(&current->sigmask_lock);
+	spin_lock_irq(&current->sig->siglock);
 	saveset = current->blocked;
 	siginitset(&current->blocked, mask);
 	recalc_sigpending();
-	spin_unlock_irq(&current->sigmask_lock);
+	spin_unlock_irq(&current->sig->siglock);
 	regs->ARM_r0 = -EINTR;
 
 	while (1) {
@@ -87,11 +87,11 @@ sys_rt_sigsuspend(sigset_t *unewset, size_t sigsetsize, struct pt_regs *regs)
 		return -EFAULT;
 	sigdelsetmask(&newset, ~_BLOCKABLE);
 
-	spin_lock_irq(&current->sigmask_lock);
+	spin_lock_irq(&current->sig->siglock);
 	saveset = current->blocked;
 	current->blocked = newset;
 	recalc_sigpending();
-	spin_unlock_irq(&current->sigmask_lock);
+	spin_unlock_irq(&current->sig->siglock);
 	regs->ARM_r0 = -EINTR;
 
 	while (1) {
@@ -207,10 +207,10 @@ asmlinkage int sys_sigreturn(struct pt_regs *regs)
 		goto badframe;
 
 	sigdelsetmask(&set, ~_BLOCKABLE);
-	spin_lock_irq(&current->sigmask_lock);
+	spin_lock_irq(&current->sig->siglock);
 	current->blocked = set;
 	recalc_sigpending();
-	spin_unlock_irq(&current->sigmask_lock);
+	spin_unlock_irq(&current->sig->siglock);
 
 	if (restore_sigcontext(regs, &frame->sc))
 		goto badframe;
@@ -247,10 +247,10 @@ asmlinkage int sys_rt_sigreturn(struct pt_regs *regs)
 		goto badframe;
 
 	sigdelsetmask(&set, ~_BLOCKABLE);
-	spin_lock_irq(&current->sigmask_lock);
+	spin_lock_irq(&current->sig->siglock);
 	current->blocked = set;
 	recalc_sigpending();
-	spin_unlock_irq(&current->sigmask_lock);
+	spin_unlock_irq(&current->sig->siglock);
 
 	if (restore_sigcontext(regs, &frame->uc.uc_mcontext))
 		goto badframe;
@@ -477,12 +477,12 @@ handle_signal(unsigned long sig, struct k_sigaction *ka,
 			ka->sa.sa_handler = SIG_DFL;
 
 		if (!(ka->sa.sa_flags & SA_NODEFER)) {
-			spin_lock_irq(&tsk->sigmask_lock);
+			spin_lock_irq(&tsk->sig->siglock);
 			sigorsets(&tsk->blocked, &tsk->blocked,
 				  &ka->sa.sa_mask);
 			sigaddset(&tsk->blocked, sig);
 			recalc_sigpending();
-			spin_unlock_irq(&tsk->sigmask_lock);
+			spin_unlock_irq(&tsk->sig->siglock);
 		}
 		return;
 	}
@@ -520,20 +520,10 @@ static int do_signal(sigset_t *oldset, struct pt_regs *regs, int syscall)
 	for (;;) {
 		unsigned long signr = 0;
 		struct k_sigaction *ka;
-		sigset_t *mask = &current->blocked;
 
-		local_irq_disable();
-		if (current->sig->shared_pending.head) {
-			spin_lock(&current->sig->siglock);
-			signr = dequeue_signal(&current->sig->shared_pending, mask, &info);
-			spin_unlock(&current->sig->siglock);
-		}
-		if (!signr) {
-			spin_lock(&current->sigmask_lock);
-			signr = dequeue_signal(&current->pending, mask, &info);
-			spin_unlock(&current->sigmask_lock);
-		}
-		local_irq_enable();
+		spin_lock_irq(&current->sig->siglock);
+		signr = dequeue_signal(&current->blocked, &info);
+		spin_unlock_irq(&current->sig->siglock);
 
 		if (!signr)
 			break;

arch/arm/kernel/time-acorn.c

@@ -25,44 +25,37 @@ extern unsigned long (*gettimeoffset)(void);
 
 static unsigned long ioctime_gettimeoffset(void)
 {
-	unsigned int count1, count2, status1, status2;
-	unsigned long offset = 0;
+	unsigned int count1, count2, status;
+	long offset;
 
-	status1 = ioc_readb(IOC_IRQREQA);
-	barrier ();
 	ioc_writeb (0, IOC_T0LATCH);
 	barrier ();
 	count1 = ioc_readb(IOC_T0CNTL) | (ioc_readb(IOC_T0CNTH) << 8);
 	barrier ();
-	status2 = ioc_readb(IOC_IRQREQA);
+	status = ioc_readb(IOC_IRQREQA);
 	barrier ();
 	ioc_writeb (0, IOC_T0LATCH);
 	barrier ();
 	count2 = ioc_readb(IOC_T0CNTL) | (ioc_readb(IOC_T0CNTH) << 8);
 
+	offset = count2;
 	if (count2 < count1) {
 		/*
-		 * This means that we haven't just had an interrupt
-		 * while reading into status2.
+		 * We have not had an interrupt between reading count1
+		 * and count2.
 		 */
-		if (status2 & (1 << 5))
-			offset = tick;
-		count1 = count2;
+		if (status & (1 << 5))
+			offset -= LATCH;
 	} else if (count2 > count1) {
 		/*
-		 * We have just had another interrupt while reading
-		 * status2.
+		 * We have just had another interrupt between reading
+		 * count1 and count2.
 		 */
-		offset += tick;
-		count1 = count2;
+		offset -= LATCH;
 	}
 
-	count1 = LATCH - count1;
-	/*
-	 * count1 = number of clock ticks since last interrupt
-	 */
-	offset += count1 * tick / LATCH;
-	return offset;
+	offset = (LATCH - offset) * (tick_nsec / 1000);
+	return (offset + LATCH/2) / LATCH;
 }
 
 void __init ioctime_init(void)

arch/arm/kernel/time.c

@@ -115,8 +115,8 @@ static inline void do_set_rtc(void)
 	    time_before(xtime.tv_sec, next_rtc_update))
 		return;
 
-	if (xtime.tv_usec < 50000 - (tick >> 1) &&
-	    xtime.tv_usec >= 50000 + (tick >> 1))
+	if (xtime.tv_nsec < 500000000 - ((unsigned) tick_nsec >> 1) &&
+	    xtime.tv_nsec >= 500000000 + ((unsigned) tick_nsec >> 1))
 		return;
 
 	if (set_rtc())
@@ -166,7 +166,7 @@ void do_gettimeofday(struct timeval *tv)
 		usec += lost * USECS_PER_JIFFY;
 
 	sec = xtime.tv_sec;
-	usec += xtime.tv_usec;
+	usec += xtime.tv_nsec / 1000;
 	read_unlock_irqrestore(&xtime_lock, flags);
 
 	/* usec may have gone up a lot: be safe */
@@ -196,7 +196,8 @@ void do_settimeofday(struct timeval *tv)
 		tv->tv_sec--;
 	}
 
-	xtime = *tv;
+	xtime.tv_sec = tv->tv_sec;
+	xtime.tv_nsec = tv->tv_usec * 1000;
 	time_adjust = 0;		/* stop active adjtime() */
 	time_status |= STA_UNSYNC;
 	time_maxerror = NTP_PHASE_LIMIT;

arch/arm/kernel/traps.c

@@ -32,6 +32,7 @@
 #include <asm/system.h>
 #include <asm/uaccess.h>
 #include <asm/unistd.h>
+#include <asm/semaphore.h>
 
 #include "ptrace.h"
 
@@ -77,8 +78,7 @@ static void dump_mem(const char *str, unsigned long bottom, unsigned long top)
 	fs = get_fs();
 	set_fs(KERNEL_DS);
 
-	printk("%s", str);
-	printk("(0x%08lx to 0x%08lx)\n", bottom, top);
+	printk("%s(0x%08lx to 0x%08lx)\n", str, bottom, top);
 
 	for (p = bottom & ~31; p < top;) {
 		printk("%04lx: ", p & 0xffff);
@@ -136,7 +136,7 @@ static void dump_instr(struct pt_regs *regs)
 	set_fs(fs);
 }
 
-static void dump_stack(struct task_struct *tsk, unsigned long sp)
+static void __dump_stack(struct task_struct *tsk, unsigned long sp)
 {
 	dump_mem("Stack: ", sp, 8192+(unsigned long)tsk->thread_info);
 }
@@ -163,15 +163,20 @@ static void dump_backtrace(struct pt_regs *regs, struct task_struct *tsk)
 }
 
 /*
- * This is called from SysRq-T (show_task) to display the current
- * call trace for each process.  Very useful.
+ * This is called from SysRq-T (show_task) to display the current call
+ * trace for each process.  This version will also display the running
+ * threads call trace (ie, us.)
  */
 void show_trace_task(struct task_struct *tsk)
 {
-	if (tsk != current) {
-		unsigned int fp = thread_saved_fp(tsk);
+	unsigned int fp;
+
+	if (tsk != current)
+		fp = thread_saved_fp(tsk);
+	else
+		asm("mov%? %0, fp" : "=r" (fp));
+
 	c_backtrace(fp, 0x10);
-	}
 }
 
 spinlock_t die_lock = SPIN_LOCK_UNLOCKED;
@@ -193,7 +198,7 @@ NORET_TYPE void die(const char *str, struct pt_regs *regs, int err)
 		current->comm, current->pid, tsk->thread_info + 1);
 
 	if (!user_mode(regs) || in_interrupt()) {
-		dump_stack(tsk, (unsigned long)(regs + 1));
+		__dump_stack(tsk, (unsigned long)(regs + 1));
 		dump_backtrace(regs, tsk);
 		dump_instr(regs);
 	}

arch/arm/mach-integrator/cpu.c

@@ -73,36 +73,37 @@ static struct vco freq_to_vco(unsigned int freq_khz, int factor)
  * Validate the speed in khz.  If it is outside our
  * range, then return the lowest.
  */
-static unsigned int
-integrator_validatespeed(unsigned int cpu, unsigned int freq_khz)
+static void integrator_verify_speed(struct cpufreq_policy *policy)
 {
 	struct vco vco;
 
-	if (freq_khz < 12000)
-		freq_khz = 12000;
-	if (freq_khz > 160000)
-		freq_khz = 160000;
+	if (policy->max > policy->max_cpu_freq)
+		policy->max = policy->max_cpu_freq;
 
-	vco = freq_to_vco(freq_khz, 1);
+	if (policy->max < 12000)
+		policy->max = 12000;
+	if (policy->max > 160000)
+		policy->max = 160000;
 
-	if (vco.vdw < 4 || vco.vdw > 152)
-		return -EINVAL;
+	vco = freq_to_vco(policy->max, 1);
 
-	return vco_to_freq(vco, 1);
+	if (vco.vdw < 4)
+		vco.vdw = 4;
+	if (vco.vdw > 152)
+		vco.vdw = 152;
+
+	policy->min = policy->max = vco_to_freq(vco, 1);
 }
 
-static void integrator_setspeed(unsigned int cpu, unsigned int freq_khz)
+static void do_set_policy(int cpu, struct cpufreq_policy *policy)
 {
-	struct vco vco = freq_to_vco(freq_khz, 1);
-	unsigned long cpus_allowed;
+	struct vco vco = freq_to_vco(policy->max, 1);
 	u_int cm_osc;
 
 	/*
-	 * Save this threads cpus_allowed mask, and bind to the
-	 * specified CPU.  When this call returns, we should be
-	 * running on the right CPU.
+	 * Bind to the specified CPU.  When this call returns,
+	 * we should be running on the right CPU.
 	 */
-	cpus_allowed = current->cpus_allowed;
 	set_cpus_allowed(current, 1 << cpu);
 	BUG_ON(cpu != smp_processor_id());
 
@@ -113,6 +114,26 @@ static void integrator_setspeed(unsigned int cpu, unsigned int freq_khz)
 	__raw_writel(0xa05f, CM_LOCK);
 	__raw_writel(cm_osc, CM_OSC);
 	__raw_writel(0, CM_LOCK);
+}
+
+static void integrator_set_policy(struct cpufreq_policy *policy)
+{
+	unsigned long cpus_allowed;
+	int cpu;
+
+	/*
+	 * Save this threads cpus_allowed mask.
+	 */
+	cpus_allowed = current->cpus_allowed;
+
+	if (policy->cpu == CPUFREQ_ALL_CPUS) {
+		for (cpu = 0; cpu < NR_CPUS; cpu++) {
+			if (!cpu_online(cpu))
+				continue;
+			do_set_policy(cpu, policy);
+		}
+	} else
+		do_set_policy(policy->cpu, policy);
 
 	/*
 	 * Restore the CPUs allowed mask.
@@ -120,23 +141,30 @@ static void integrator_setspeed(unsigned int cpu, unsigned int freq_khz)
 	set_cpus_allowed(current, cpus_allowed);
 }
 
+static struct cpufreq_policy integrator_policy = {
+	.cpu		= 0,
+	.policy		= CPUFREQ_POLICY_POWERSAVE,
+	.max_cpu_freq	= 160000,
+};
+
 static struct cpufreq_driver integrator_driver = {
-	.validate	= integrator_validatespeed,
-	.setspeed	= integrator_setspeed,
-	.sync		= 1,
+	.verify		= integrator_verify_speed,
+	.setpolicy	= integrator_set_policy,
+	.policy		= &integrator_policy,
+	.cpu_min_freq	= 12000,
 };
 #endif
 
 static int __init integrator_cpu_init(void)
 {
-	struct cpufreq_freqs *freqs;
+	struct cpufreq_policy *policies;
 	unsigned long cpus_allowed;
 	int cpu;
 
-	freqs = kmalloc(sizeof(struct cpufreq_freqs) * NR_CPUS,
+	policies = kmalloc(sizeof(struct cpufreq_freqs) * NR_CPUS,
 			   GFP_KERNEL);
-	if (!freqs) {
-		printk(KERN_ERR "CPU: unable to allocate cpufreqs structure\n");
+	if (!policies) {
+		printk(KERN_ERR "CPU: unable to allocate policies structure\n");
 		return -ENOMEM;
 	}
 
@@ -164,18 +192,20 @@ static int __init integrator_cpu_init(void)
 		vco.od = (cm_osc >> 8) & 7;
 		vco.vdw = cm_osc & 255;
 
-		freqs[cpu].min = 12000;
-		freqs[cpu].max = 160000;
-		freqs[cpu].cur = vco_to_freq(vco, 1);
+		policies[cpu].cpu = cpu;
+		policies[cpu].policy = CPUFREQ_POLICY_POWERSAVE,
+		policies[cpu].max_cpu_freq = 160000;
+		policies[cpu].min =
+		policies[cpu].max = vco_to_freq(vco, 1);
 	}
 
 	set_cpus_allowed(current, cpus_allowed);
 
 #ifdef CONFIG_CPU_FREQ
-	integrator_driver.freq = freqs;
+	integrator_driver.policy = policies;
 	cpufreq_register(&integrator_driver);
 #else
-	kfree(freqs);
+	kfree(policies);
 #endif
 
 	return 0;

arch/arm/mach-iop310/iop310-pci.c

@@ -145,7 +145,7 @@ iop310_pri_read_config(struct pci_bus *bus, unsigned int devfn, int where,
 }
 
 static int
-iop310_pri_write_config(struct pci_bus *bus, unsigned int devfn, int where
+iop310_pri_write_config(struct pci_bus *bus, unsigned int devfn, int where,
 			int size, u32 value)
 {
 	unsigned long addr = iop310_cfg_address(bus, devfn, where);
@@ -163,7 +163,7 @@ iop310_pri_write_config(struct pci_bus *bus, unsigned int devfn, int where
 		else
 			val &= ~(0xffff << where);
 
-		*IOP310_POCCDR = val | v << where;
+		*IOP310_POCCDR = val | value << where;
 	} else {
 		asm volatile(
 			"str	%1, [%2]\n\t"
@@ -173,7 +173,7 @@ iop310_pri_write_config(struct pci_bus *bus, unsigned int devfn, int where
 			"nop\n\t"
 			"nop\n\t"
 			:
-			: "r" (val), "r" (addr),
+			: "r" (value), "r" (addr),
 			  "r" (IOP310_POCCAR), "r" (IOP310_POCCDR));
 	}
 
@@ -246,7 +246,7 @@ iop310_sec_read_config(struct pci_bus *bus, unsigned int devfn, int where,
 }
 
 static int
-iop310_sec_write_config(struct pci_bus *bus, unsigned int devfn, int where
+iop310_sec_write_config(struct pci_bus *bus, unsigned int devfn, int where,
 			int size, u32 value)
 {
 	unsigned long addr = iop310_cfg_address(bus, devfn, where);
@@ -265,7 +265,7 @@ iop310_sec_write_config(struct pci_bus *bus, unsigned int devfn, int where
 		else
 			val &= ~(0xffff << where);
 
-		*IOP310_SOCCDR = val | v << where;
+		*IOP310_SOCCDR = val | value << where;
 	} else {
 		asm volatile(
 			"str	%1, [%2]\n\t"
@@ -275,7 +275,7 @@ iop310_sec_write_config(struct pci_bus *bus, unsigned int devfn, int where
 			"nop\n\t"
 			"nop\n\t"
 			:
-			: "r" (val), "r" (addr),
+			: "r" (value), "r" (addr),
 			  "r" (IOP310_SOCCAR), "r" (IOP310_SOCCDR));
 	}
 

arch/arm/mach-iop310/iq80310-time.c

@@ -85,7 +85,7 @@ static unsigned long iq80310_gettimeoffset (void)
 	/*
 	 * Now convert them to usec.
 	 */
-	usec = (unsigned long)(elapsed*tick)/LATCH;
+	usec = (unsigned long)(elapsed * (tick_nsec / 1000))/LATCH;
 
 	return usec;
 }

arch/arm/mach-sa1100/Makefile

@@ -2,20 +2,17 @@
 # Makefile for the linux kernel.
 #
 
-# Common support (must be linked before board specific support)
+# Common support
 obj-y := generic.o irq.o dma.o
 obj-m :=
 obj-n :=
 obj-  :=
 led-y := leds.o
 
-export-objs :=	dma.o generic.o pcipool.o pm.o sa1111.o sa1111-pcibuf.o \
-		usb_ctl.o usb_recv.o usb_send.o
+export-objs := dma.o generic.o pcipool.o pm.o sa1111.o sa1111-pcibuf.o
 
 # This needs to be cleaned up.  We probably need to have SA1100
 # and SA1110 config symbols.
-#
-# We link the CPU support next, so that RAM timings can be tuned.
 ifeq ($(CONFIG_CPU_FREQ),y)
 obj-$(CONFIG_SA1100_ASSABET)		+= cpu-sa1110.o
 obj-$(CONFIG_SA1100_CERF)		+= cpu-sa1110.o
@@ -107,10 +104,7 @@ export-objs				+= yopy.o
 obj-$(CONFIG_LEDS) += $(led-y)
 
 # SA1110 USB client support
-sa1100usb_core-objs := usb_ctl.o usb_ep0.o usb_recv.o usb_send.o
-obj-$(CONFIG_SA1100_USB) += sa1100usb_core.o
-obj-$(CONFIG_SA1100_USB_NETLINK) += usb-eth.o
-obj-$(CONFIG_SA1100_USB_CHAR) += usb-char.o
+#obj-$(CONFIG_SA1100_USB)		+= usb/
 
 # Miscelaneous functions
 obj-$(CONFIG_PM) += pm.o sleep.o

arch/arm/mach-sa1100/assabet.c

@@ -302,21 +302,24 @@ static void __init assabet_map_io(void)
 		 */
 		neponset_map_io();
 #endif
+	} else {
+		sa1100_register_uart_fns(&assabet_port_fns);
+	}
+
 	/*
 	 * When Neponset is attached, the first UART should be
 	 * UART3.  That's what Angel is doing and many documents
 	 * are stating this.
+	 *
 	 * We do the Neponset mapping even if Neponset support
 	 * isn't compiled in so the user will still get something on
 	 * the expected physical serial port.
+	 *
+	 * We no longer do this; not all boot loaders support it,
+	 * and UART3 appears to be somewhat unreliable with blob.
 	 */
-		sa1100_register_uart(0, 3);
-		sa1100_register_uart(2, 1);
-	} else {
-		sa1100_register_uart_fns(&assabet_port_fns);
-		sa1100_register_uart(0, 1);	/* com port */
-		sa1100_register_uart(2, 3);	/* radio module */
-	}
+	sa1100_register_uart(0, 1);
+	sa1100_register_uart(2, 3);
 }
 
 

arch/arm/mach-sa1100/generic.c

@@ -55,8 +55,8 @@ unsigned int sa11x0_freq_to_ppcr(unsigned int khz)
 
 	khz /= 100;
 
-	for (i = 0; i < ARRAY_SIZE(cclk_frequency_100khz); i--)
-		if (cclk_frequency_100khz[i] >= khz)
+	for (i = NR_FREQS - 1; i > 0; i--)
+		if (cclk_frequency_100khz[i] <= khz)
 			break;
 
 	return i;

arch/arm/mach-sa1100/neponset.c

@@ -193,20 +193,30 @@ static int neponset_resume(struct device *dev, u32 level)
 }
 
 static struct device_driver neponset_device_driver = {
+	.name		= "NEPONSET",
+	.bus		= &system_bus_type,
 	.suspend	= neponset_suspend,
 	.resume		= neponset_resume,
 };
 
-static struct device neponset_device = {
+static struct sys_device neponset_device = {
+	.name		= "NEPONSET",
+	.id		= 0,
+	.root		= NULL,
+	.dev = {
 		.name	= "Neponset",
 		.bus_id	= "neponset",
+		.bus	= &system_bus_type,
 		.driver = &neponset_device_driver,
+	},
 };
 
 static int __init neponset_init(void)
 {
 	int ret;
 
+	driver_register(&neponset_device_driver);
+
 	/*
 	 * The Neponset is only present on the Assabet machine type.
 	 */
@@ -231,7 +241,7 @@ static int __init neponset_init(void)
 		return -ENODEV;
 	}
 
-	ret = register_sys_device(&neponset_device);
+	ret = sys_device_register(&neponset_device);
 	if (ret)
 		return ret;
 
@@ -256,7 +266,7 @@ static int __init neponset_init(void)
 	return sa1111_init(0x40000000, IRQ_NEPONSET_SA1111);
 }
 
-arch_initcall(neponset_init);
+subsys_initcall(neponset_init);
 
 static struct map_desc neponset_io_desc[] __initdata = {
  /* virtual     physical    length type */

arch/arm/mm/fault-armv.c

@@ -16,8 +16,10 @@
 #include <linux/bitops.h>
 #include <linux/init.h>
 
+#include <asm/cacheflush.h>
 #include <asm/pgalloc.h>
 #include <asm/pgtable.h>
+#include <asm/tlbflush.h>
 
 #include "fault.h"
 

arch/arm/mm/init.c

@@ -519,6 +519,10 @@ void __init paging_init(struct meminfo *mi, struct machine_desc *mdesc)
 				bdata->node_boot_start >> PAGE_SHIFT, zhole_size);
 	}
 
+#ifndef CONFIG_DISCONTIGMEM
+	mem_map = contig_page_data.node_mem_map;
+#endif
+
 	/*
 	 * finish off the bad pages once
 	 * the mem_map is initialised
@@ -559,7 +563,9 @@ void __init mem_init(void)
 	initpages = &__init_end - &__init_begin;
 
 	high_memory = (void *)__va(meminfo.end);
+#ifndef CONFIG_DISCONTIGMEM
 	max_mapnr   = virt_to_page(high_memory) - mem_map;
+#endif
 
 	/*
 	 * We may have non-contiguous memory.

arch/arm/mm/minicache.c

@@ -15,9 +15,11 @@
  */
 #include <linux/init.h>
 #include <linux/mm.h>
+
 #include <asm/page.h>
 #include <asm/pgalloc.h>
 #include <asm/pgtable.h>
+#include <asm/tlbflush.h>
 
 /*
  * 0xffff8000 to 0xffffffff is reserved for any ARM architecture

arch/arm/mm/mm-armv.c

@@ -13,6 +13,7 @@
 #include <linux/mm.h>
 #include <linux/init.h>
 #include <linux/bootmem.h>
+#include <linux/highmem.h>
 
 #include <asm/pgtable.h>
 #include <asm/pgalloc.h>
@@ -20,6 +21,7 @@
 #include <asm/rmap.h>
 #include <asm/io.h>
 #include <asm/setup.h>
+#include <asm/tlbflush.h>
 
 #include <asm/mach/map.h>
 
@@ -213,6 +215,50 @@ static inline void clear_mapping(unsigned long virt)
 	pmd_clear(pmd_offset(pgd_offset_k(virt), virt));
 }
 
+struct mem_types {
+	unsigned int	prot_pte;
+	unsigned int	prot_sect;
+	unsigned int	domain;
+};
+
+static struct mem_types mem_types[] __initdata = {
+	[MT_DEVICE] = {
+		.prot_pte  = L_PTE_PRESENT | L_PTE_YOUNG | L_PTE_DIRTY |
+				L_PTE_WRITE,
+		.prot_sect = PMD_TYPE_SECT | PMD_SECT_AP_WRITE,
+		.domain    = DOMAIN_IO,
+	},
+	[MT_CACHECLEAN] = {
+		.prot_pte  = L_PTE_PRESENT | L_PTE_YOUNG | L_PTE_DIRTY |
+				L_PTE_CACHEABLE | L_PTE_BUFFERABLE,
+		.prot_sect = PMD_TYPE_SECT | PMD_SECT_CACHEABLE |
+				PMD_SECT_BUFFERABLE,
+		.domain    = DOMAIN_KERNEL,
+	},
+	[MT_MINICLEAN] = {
+		.prot_pte  = L_PTE_PRESENT | L_PTE_YOUNG | L_PTE_DIRTY |
+				L_PTE_CACHEABLE,
+		.prot_sect = PMD_TYPE_SECT | PMD_SECT_CACHEABLE,
+		.domain    = DOMAIN_KERNEL,
+	},
+	[MT_VECTORS] = {
+		.prot_pte  = L_PTE_PRESENT | L_PTE_YOUNG | L_PTE_DIRTY |
+				L_PTE_CACHEABLE | L_PTE_BUFFERABLE |
+				L_PTE_EXEC,
+		.prot_sect = PMD_TYPE_SECT | PMD_SECT_CACHEABLE |
+				PMD_SECT_BUFFERABLE,
+		.domain    = DOMAIN_USER,
+	},
+	[MT_MEMORY] = {
+		.prot_pte  = L_PTE_PRESENT | L_PTE_YOUNG | L_PTE_DIRTY |
+				L_PTE_CACHEABLE | L_PTE_BUFFERABLE |
+				L_PTE_EXEC | L_PTE_WRITE,
+		.prot_sect = PMD_TYPE_SECT | PMD_SECT_CACHEABLE |
+				PMD_SECT_BUFFERABLE | PMD_SECT_AP_WRITE,
+		.domain    = DOMAIN_KERNEL,
+	}
+};
+
 /*
  * Create the page directory entries and any necessary
  * page tables for the mapping specified by `md'.  We
@@ -232,42 +278,9 @@ static void __init create_mapping(struct map_desc *md)
 		return;
 	}
 
-	prot_pte  = L_PTE_PRESENT | L_PTE_YOUNG | L_PTE_DIRTY;
-	prot_sect = PMD_TYPE_SECT;
-
-	switch (md->type) {
-	case MT_DEVICE:
-		prot_pte  |= L_PTE_WRITE;
-		prot_sect |= PMD_SECT_AP_WRITE;
-		domain     = DOMAIN_IO;
-		break;
-
-	case MT_CACHECLEAN:
-		prot_pte  |= L_PTE_CACHEABLE | L_PTE_BUFFERABLE;
-		prot_sect |= PMD_SECT_CACHEABLE | PMD_SECT_BUFFERABLE;
-		domain     = DOMAIN_KERNEL;
-		break;
-
-	case MT_MINICLEAN:
-		prot_pte  |= L_PTE_CACHEABLE;
-		prot_sect |= PMD_SECT_CACHEABLE;
-		domain     = DOMAIN_KERNEL;
-		break;
-
-	case MT_VECTORS:
-		prot_pte  |= L_PTE_EXEC | L_PTE_CACHEABLE | L_PTE_BUFFERABLE;
-		prot_sect |= PMD_SECT_CACHEABLE | PMD_SECT_BUFFERABLE;
-		domain     = DOMAIN_USER;
-		break;
-
-	case MT_MEMORY:
-		prot_pte  |= L_PTE_WRITE | L_PTE_EXEC | L_PTE_CACHEABLE | L_PTE_BUFFERABLE;
-		prot_sect |= PMD_SECT_AP_WRITE | PMD_SECT_CACHEABLE | PMD_SECT_BUFFERABLE;
-		domain     = DOMAIN_KERNEL;
-		break;
-	}
-
-	prot_sect |= PMD_DOMAIN(domain);
+	domain	  = mem_types[md->type].domain;
+	prot_pte  = mem_types[md->type].prot_pte;
+	prot_sect = mem_types[md->type].prot_sect | PMD_DOMAIN(domain);
 
 	virt   = md->virtual;
 	off    = md->physical - virt;

arch/arm/mm/proc-syms.c

@@ -10,8 +10,10 @@
 #include <linux/module.h>
 #include <linux/mm.h>
 
+#include <asm/cacheflush.h>
 #include <asm/pgalloc.h>
 #include <asm/proc-fns.h>
+#include <asm/tlbflush.h>
 
 #ifndef MULTI_CPU
 EXPORT_SYMBOL(cpu_cache_clean_invalidate_all);
@@ -29,11 +31,11 @@ EXPORT_SYMBOL(cpu_set_pte);
 EXPORT_SYMBOL(processor);
 #endif
 
-#ifndef MULTI_TLB
-EXPORT_SYMBOL_NOVERS(__cpu_flush_kern_tlb_all);
-EXPORT_SYMBOL_NOVERS(__cpu_flush_user_tlb_mm);
-EXPORT_SYMBOL_NOVERS(__cpu_flush_user_tlb_range);
-EXPORT_SYMBOL_NOVERS(__cpu_flush_user_tlb_page);
-#else
+/*
+ * No module should need to touch the TLB (and currently
+ * no modules do.  We export this for "loadkernel" support
+ * (booting a new kernel from within a running kernel.)
+ */
+#ifdef MULTI_TLB
 EXPORT_SYMBOL(cpu_tlb);
 #endif

arch/arm/mm/tlb-v3.S

@@ -13,31 +13,10 @@
  */
 #include <linux/linkage.h>
 #include <asm/constants.h>
+#include <asm/tlbflush.h>
 #include "proc-macros.S"
 
 	.align	5
-/*
- *	v3_flush_user_tlb_mm(mm)
- *
- *	Invalidate all TLB entries in a particular address space
- *
- *	- mm    - mm_struct describing address space
- */
-ENTRY(v3_flush_user_tlb_mm)
-	act_mm	r1				@ get current->active_mm
-	teq	r0, r1				@ == mm ?
-	movne	pc, lr				@ no, we dont do anything
-
-/*
- *	v3_flush_kern_tlb_all()
- *
- *	Invalidate the entire TLB
- */
-ENTRY(v3_flush_kern_tlb_all)
-	mov	r0, #0
-	mcr	p15, 0, r0, c5, c0, 0		@ invalidate TLB
-	mov	pc, lr
-
 /*
  *	v3_flush_user_tlb_range(start, end, mm)
  *
@@ -62,32 +41,11 @@ ENTRY(v3_flush_kern_tlb_range)
 	blo	1b
 	mov	pc, lr
 
-/*
- *	v3_flush_user_tlb_page(vaddr,vma)
- *
- *	Invalidate the specified page in the specified address space.
- *
- *	- vaddr - virtual address (may not be aligned)
- *	- vma   - vma_struct describing address range
- */
-	.align	5
-ENTRY(v3_flush_user_tlb_page)
-	vma_vm_mm r2, r1			@ get vma->vm_mm
-	act_mm	r3				@ get current->active_mm
-	teq	r2, r3				@ equal
-	movne	pc, lr				@ no
-ENTRY(v3_flush_kern_tlb_page)
-	mcr	p15, 0, r0, c6, c0, 0		@ invalidate TLB entry
-	mov	pc, lr
-
 	.section ".text.init", #alloc, #execinstr
 
 	.type	v3_tlb_fns, #object
 ENTRY(v3_tlb_fns)
-	.long	v3_flush_kern_tlb_all
-	.long	v3_flush_user_tlb_mm
 	.long	v3_flush_user_tlb_range
-	.long	v3_flush_user_tlb_page
 	.long	v3_flush_kern_tlb_range
-	.long	v3_flush_kern_tlb_page
+	.long	v3_tlb_flags
 	.size	v3_tlb_fns, . - v3_tlb_fns

arch/arm/mm/tlb-v4.S

@@ -14,31 +14,10 @@
  */
 #include <linux/linkage.h>
 #include <asm/constants.h>
+#include <asm/tlbflush.h>
 #include "proc-macros.S"
 
 	.align	5
-/*
- *	v4_flush_user_tlb_mm(mm)
- *
- *	Invalidate all TLB entries in a particular address space
- *
- *	- mm    - mm_struct describing address space
- */
-ENTRY(v4_flush_user_tlb_mm)
-	act_mm	r1				@ get current->active_mm
-	teq	r0, r1				@ == mm ?
-	movne	pc, lr				@ no, we dont do anything
-
-/*
- *	v4_flush_kern_tlb_all()
- *
- *	Invalidate the entire TLB
- */
-ENTRY(v4_flush_kern_tlb_all)
-	mov	r0, #0
-	mcr	p15, 0, r0, c8, c7, 0		@ invalidate I + D TLBs
-	mov	pc, lr
-
 /*
  *	v4_flush_user_tlb_range(start, end, mm)
  *
@@ -64,25 +43,6 @@ ENTRY(v4_flush_user_tlb_range)
 	blo	1b
 	mov	pc, lr
 
-/*
- *	v4_flush_user_tlb_page(vaddr,vma)
- *
- *	Invalidate the specified page in the specified address space.
- *
- *	- vaddr - virtual address (may not be aligned)
- *	- vma   - vma_struct describing address range
- */
-	.align	5
-ENTRY(v4_flush_user_tlb_page)
-	vma_vm_mm r2, r1			@ get vma->vm_mm
-	act_mm	r3				@ get current->active_mm
-	teq	r2, r3				@ equal
-	movne	pc, lr				@ no
-	vma_vm_flags r2, r1
-.v4_flush_kern_tlb_page:
-	mcr	p15, 0, r0, c8, c7, 1		@ invalidate TLB entry
-	mov	pc, lr
-
 /*
  *	v4_flush_kerm_tlb_range(start, end)
  *
@@ -95,27 +55,11 @@ ENTRY(v4_flush_user_tlb_page)
 .globl v4_flush_kern_tlb_range
 .equ v4_flush_kern_tlb_range, .v4_flush_kern_tlb_range
 
-
-/*
- *	v4_flush_kern_tlb_page(kaddr)
- *
- *	Invalidate the TLB entry for the specified page.  The address
- *	will be in the kernels virtual memory space.  Current uses
- *	only require the D-TLB to be invalidated.
- *
- *	- kaddr - Kernel virtual memory address
- */
-.globl v4_flush_kern_tlb_page
-.equ v4_flush_kern_tlb_page, .v4_flush_kern_tlb_page
-
 	.section ".text.init", #alloc, #execinstr
 
 	.type	v4_tlb_fns, #object
 ENTRY(v4_tlb_fns)
-	.long	v4_flush_kern_tlb_all
-	.long	v4_flush_user_tlb_mm
 	.long	v4_flush_user_tlb_range
-	.long	v4_flush_user_tlb_page
 	.long	v4_flush_kern_tlb_range
-	.long	v4_flush_kern_tlb_page
+	.long	v4_tlb_flags
 	.size	v4_tlb_fns, . - v4_tlb_fns

arch/arm/mm/tlb-v4wb.S

@@ -14,34 +14,10 @@
  */
 #include <linux/linkage.h>
 #include <asm/constants.h>
+#include <asm/tlbflush.h>
 #include "proc-macros.S"
 
 	.align	5
-/*
- *	v4wb_flush_user_tlb_mm(mm)
- *
- *	Invalidate all TLB entries in a particular address space
- *
- *	- mm    - mm_struct describing address space
- */
-ENTRY(v4wb_flush_user_tlb_mm)
-ENTRY(v4wbi_flush_user_tlb_mm)
-	act_mm	r1				@ get current->active_mm
-	teq	r0, r1				@ == mm ?
-	movne	pc, lr				@ no, we dont do anything
-
-/*
- *	v4wb_flush_tlb_all()
- *
- *	Invalidate the entire TLB
- */
-ENTRY(v4wb_flush_kern_tlb_all)
-ENTRY(v4wbi_flush_kern_tlb_all)
-	mov	r0, #0
-	mcr	p15, 0, r0, c7, c10, 4		@ drain WB
-	mcr	p15, 0, r0, c8, c7, 0		@ invalidate I + D TLBs
-	mov	pc, lr
-
 /*
  *	v4wb_flush_user_tlb_range(start, end, mm)
  *
@@ -69,28 +45,6 @@ ENTRY(v4wb_flush_user_tlb_range)
 	blo	1b
 	mov	pc, lr
 
-/*
- *	v4wb_flush_user_tlb_page(vaddr,vma)
- *
- *	Invalidate the specified page in the specified address space.
- *
- *	- vaddr - virtual address (may not be aligned)
- *	- vma   - vma_struct describing address range
- */
-	.align	5
-ENTRY(v4wb_flush_user_tlb_page)
-	vma_vm_mm r2, r1			@ get vma->vm_mm
-	act_mm	r3				@ get current->active_mm
-	teq	r2, r3				@ equal
-	movne	pc, lr				@ no
-	vma_vm_flags r2, r1
-	mov	r3, #0
-	mcr	p15, 0, r3, c7, c10, 4		@ drain WB
-	tst	r2, #VM_EXEC
-	mcrne	p15, 0, r3, c8, c5, 0		@ invalidate I TLB
-	mcr	p15, 0, r0, c8, c6, 1		@ invalidate D TLB entry
-	mov	pc, lr
-
 /*
  *	v4_flush_kerm_tlb_range(start, end)
  *
@@ -112,20 +66,6 @@ ENTRY(v4wb_flush_kern_tlb_range)
 	blo	1b
 	mov	pc, lr
 
-/*
- *	v4_flush_kern_tlb_page(kaddr)
- *
- *	Invalidate the TLB entry for the specified page.  The address
- *	will be in the kernels virtual memory space.  Current uses
- *	only require the D-TLB to be invalidated.
- *
- *	- kaddr - Kernel virtual memory address
- */
-ENTRY(v4wb_flush_kern_tlb_page)
-	mcr	p15, 0, r3, c8, c5, 0		@ invalidate I TLB
-	mcr	p15, 0, r0, c8, c6, 1		@ invalidate D TLB entry
-	mov	pc, lr
-
 /*
  * These two are optimised for ARM920, ARM922, ARM926, Xscale
  */
@@ -158,28 +98,6 @@ ENTRY(v4wbi_flush_user_tlb_range)
 	blo	1b
 	mov	pc, lr
 
-/*
- *	v4wb_flush_tlb_page(vaddr,vma)
- *
- *	Invalidate the specified page in the specified address space.
- *
- *	- vaddr - virtual address (may not be aligned)
- *	- vma   - vma_struct describing address range
- */
-	.align	5
-ENTRY(v4wbi_flush_user_tlb_page)
-	vma_vm_mm r2, r1			@ get vma->vm_mm
-	act_mm	r3				@ get current->active_mm
-	teq	r2, r3				@ equal
-	movne	pc, lr				@ no
-	vma_vm_flags r2, r1
-	mov	r3, #0
-	mcr	p15, 0, r3, c7, c10, 4		@ drain WB
-	tst	r2, #VM_EXEC
-	mcrne	p15, 0, r0, c8, c5, 1		@ invalidate I TLB entry
-	mcr	p15, 0, r0, c8, c6, 1		@ invalidate D TLB entry
-	mov	pc, lr
-
 ENTRY(v4wbi_flush_kern_tlb_range)
 	mov	r3, #0
 	mcr	p15, 0, r3, c7, c10, 4		@ drain WB
@@ -192,29 +110,18 @@ ENTRY(v4wbi_flush_kern_tlb_range)
 	blo	1b
 	mov	pc, lr
 
-ENTRY(v4wbi_flush_kern_tlb_page)
-	mcr	p15, 0, r0, c8, c5, 1		@ invalidate I TLB entry
-	mcr	p15, 0, r0, c8, c6, 1		@ invalidate D TLB entry
-	mov	pc, lr
-
 	.section ".text.init", #alloc, #execinstr
 
 	.type	v4wb_tlb_fns, #object
 ENTRY(v4wb_tlb_fns)
-	.long	v4wb_flush_kern_tlb_all
-	.long	v4wb_flush_user_tlb_mm
 	.long	v4wb_flush_user_tlb_range
-	.long	v4wb_flush_user_tlb_page
 	.long	v4wb_flush_kern_tlb_range
-	.long	v4wb_flush_kern_tlb_page
+	.long	v4wb_tlb_flags
 	.size	v4wb_tlb_fns, . - v4wb_tlb_fns
 
 	.type	v4wbi_tlb_fns, #object
 ENTRY(v4wbi_tlb_fns)
-	.long	v4wbi_flush_kern_tlb_all
-	.long	v4wbi_flush_user_tlb_mm
 	.long	v4wbi_flush_user_tlb_range
-	.long	v4wbi_flush_user_tlb_page
 	.long	v4wbi_flush_kern_tlb_range
-	.long	v4wbi_flush_kern_tlb_page
+	.long	v4wbi_tlb_flags
 	.size	v4wbi_tlb_fns, . - v4wbi_tlb_fns

arch/arm/vmlinux.lds.S

@@ -4,13 +4,10 @@
 
 #ifdef CONFIG_ROM_KERNEL
 
-#define DATAADDR 0x02080000
-#define TEXTADDR 0x03800000
 #include "vmlinux-armo-rom.lds.in"
 
 #else
 
-#define TEXTADDR 0x02080000
 #include "vmlinux-armo.lds.in"
 
 #endif
@@ -19,7 +16,6 @@
 
 #ifdef CONFIG_CPU_32
 
-#define TEXTADDR 0xC0008000
 #include "vmlinux-armv.lds.in"
 
 #endif

drivers/acorn/block/fd1772.c

@@ -345,8 +345,6 @@ static void fd_select_drive(int drive);
 static void fd_deselect(void);
 static void fd_motor_off_timer(unsigned long dummy);
 static void check_change(unsigned long dummy);
-static __inline__ void set_head_settle_flag(void);
-static __inline__ int get_head_settle_flag(void);
 static void floppy_irqconsequencehandler(void);
 static void fd_error(void);
 static void do_fd_action(int drive);
@@ -363,7 +361,6 @@ static void fd_times_out(unsigned long dummy);
 static void finish_fdc(void);
 static void finish_fdc_done(int dummy);
 static void floppy_off(unsigned int nr);
-static __inline__ void copy_buffer(void *from, void *to);
 static void setup_req_params(int drive);
 static void redo_fd_request(void);
 static int fd_ioctl(struct inode *inode, struct file *filp, unsigned int
@@ -543,12 +540,12 @@ static void check_change(unsigned long dummy)
  * seek operation, because we don't use seeks with verify.
  */
 
-static __inline__ void set_head_settle_flag(void)
+static inline void set_head_settle_flag(void)
 {
 	HeadSettleFlag = FDC1772CMDADD_E;
 }
 
-static __inline__ int get_head_settle_flag(void)
+static inline int get_head_settle_flag(void)
 {
 	int tmp = HeadSettleFlag;
 	HeadSettleFlag = 0;
@@ -560,6 +557,15 @@ static __inline__ int get_head_settle_flag(void)
 
 /* General Interrupt Handling */
 
+static inline void copy_buffer(void *from, void *to)
+{
+	ulong *p1 = (ulong *) from, *p2 = (ulong *) to;
+	int cnt;
+
+	for (cnt = 512 / 4; cnt; cnt--)
+		*p2++ = *p1++;
+}
+
 static void (*FloppyIRQHandler) (int status) = NULL;
 
 static void floppy_irqconsequencehandler(void)
@@ -1175,16 +1181,6 @@ static int floppy_revalidate(dev_t dev)
 	return 0;
 }
 
-static __inline__ void copy_buffer(void *from, void *to)
-{
-	ulong *p1 = (ulong *) from, *p2 = (ulong *) to;
-	int cnt;
-
-	for (cnt = 512 / 4; cnt; cnt--)
-		*p2++ = *p1++;
-}
-
-
 /* This sets up the global variables describing the current request. */
 
 static void setup_req_params(int drive)

drivers/acorn/char/Makefile

@@ -3,17 +3,10 @@
 #
 
 # All the objects that export symbols.
-obj-arc		:= keyb_arc.o
-obj-rpc		:= keyb_ps2.o
-obj-clps7500	:= keyb_ps2.o defkeymap-acorn.o
-
-obj-$(CONFIG_RPCMOUSE)		+= mouse_rpc.o
-obj-$(CONFIG_ATOMWIDE_SERIAL)	+= serial-atomwide.o
-obj-$(CONFIG_DUALSP_SERIAL)	+= serial-dualsp.o
-obj-$(CONFIG_ARCH_ACORN)	+= defkeymap-acorn.o i2c.o pcf8583.o
-obj-$(CONFIG_L7200_KEYB)	+= defkeymap-l7200.o keyb_l7200.o
+obj-arc		:= keyb_arc.o defkeymap-acorn.o
 
-# Do the i2c and rtc last
+obj-$(CONFIG_ARCH_ACORN)	+= i2c.o pcf8583.o
+obj-$(CONFIG_L7200_KEYB)	+= defkeymap-l7200.o keyb_l7200.o
 obj-y				+= $(obj-$(MACHINE))
 
 include $(TOPDIR)/Rules.make

drivers/acorn/char/i2c.c

@@ -132,7 +132,7 @@ static int k_set_rtc_time(void)
 	if (rtc_command(RTC_GETDATETIME, &old_rtctm))
 		return 0;
 
-	new_rtctm.cs    = xtime.tv_usec / 10000;
+	new_rtctm.cs    = xtime.tv_nsec / 10000000;
 	new_rtctm.secs  = nowtime % 60;	nowtime /= 60;
 	new_rtctm.mins  = nowtime % 60;	nowtime /= 60;
 	new_rtctm.hours = nowtime % 24;
@@ -283,7 +283,7 @@ static int ioc_client_reg(struct i2c_client *client)
 		rtc_client = client;
 		get_rtc_time(&rtctm, &year);
 
-		xtime.tv_usec = rtctm.cs * 10000;
+		xtime.tv_nsec = rtctm.cs * 10000000;
 		xtime.tv_sec  = mktime(year, rtctm.mon, rtctm.mday,
 				       rtctm.hours, rtctm.mins, rtctm.secs);
 		set_rtc = k_set_rtc_time;

drivers/acorn/char/mouse_rpc.c

-/*
- *  linux/drivers/char/mouse_rpc.c
- *
- *  Copyright (C) 1996-1998 Russell King
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- *  This handles the Acorn RiscPCs mouse.  We basically have a couple
- *  of hardware registers that track the sensor count for the X-Y movement
- *  and another register holding the button state.  On every VSYNC interrupt
- *  we read the complete state and then work out if something has changed.
- */
-#include <linux/module.h>
-#include <linux/sched.h>
-#include <linux/ptrace.h>
-#include <linux/interrupt.h>
-#include <linux/init.h>
-#include <linux/errno.h>
-
-#include <asm/hardware.h>
-#include <asm/irq.h>
-#include <asm/io.h>
-#include <asm/hardware/iomd.h>
-
-#include "../../char/busmouse.h"
-
-static short old_x, old_y, old_b;
-static int mousedev;
-
-void
-mouse_rpc_irq(int irq, void *dev_id, struct pt_regs *regs)
-{
-	short x, y, dx, dy;
-	int buttons;
-
-	x = (short)iomd_readl(IOMD_MOUSEX);
-	y = (short)iomd_readl(IOMD_MOUSEY);
-	buttons = (__raw_readl(0xe0310000) >> 4) & 7;
-
-	dx = x - old_x;
-	old_x = x;
-	dy = y - old_y;
-	old_y = y;
-
-	if (dx || dy || buttons != old_b) {
-		busmouse_add_movementbuttons(mousedev, dx, dy, buttons);
-		old_b = buttons;
-	}
-}
-
-static struct busmouse rpcmouse = {
-	6, "arcmouse", NULL, NULL, NULL, 7
-};
-
-static int __init mouse_rpc_init(void)
-{
-	mousedev = register_busmouse(&rpcmouse);
-
-	if (mousedev < 0)
-		printk("rpcmouse: could not register mouse driver\n");
-	else {
-		old_x = (short)iomd_readl(IOMD_MOUSEX);
-		old_y = (short)iomd_readl(IOMD_MOUSEY);
-		old_b = (__raw_readl(0xe0310000) >> 4) & 7;
-		if (request_irq(IRQ_VSYNCPULSE, mouse_rpc_irq, SA_SHIRQ, "mouse", &mousedev)) {
-			printk("rpcmouse: unable to allocate VSYNC interrupt\n");
-			unregister_busmouse(mousedev);
-			mousedev = -1;
-		}
-	}
-
-	return mousedev >= 0 ? 0 : -ENODEV;
-}
-
-static void __exit mouse_rpc_exit(void)
-{
-	if (mousedev >= 0) {
-		unregister_busmouse(mousedev);
-		free_irq(IRQ_VSYNCPULSE, &mousedev);
-	}
-}
-
-module_init(mouse_rpc_init);
-module_exit(mouse_rpc_exit);
-
-MODULE_AUTHOR("Russell King");
-MODULE_DESCRIPTION("RiscPC mouse driver");
-MODULE_LICENSE("GPL");
-

drivers/acorn/char/serial-atomwide.c

-/*
- *  linux/arch/arm/drivers/char/serial-atomwide.c
- *
- *  Copyright (C) 1996 Russell King.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- *  Changelog:
- *   02-05-1996	RMK	Created
- *   07-05-1996	RMK	Altered for greater number of cards.
- *   30-07-1996	RMK	Now uses generic card code.
- */
-#define MY_CARD_LIST { MANU_ATOMWIDE, PROD_ATOMWIDE_3PSERIAL }
-#define MY_NUMPORTS 3
-#define MY_BAUD_BASE (7372800 / 16)
-#define MY_BASE_ADDRESS(ec) \
-	ecard_address ((ec), ECARD_IOC, ECARD_SLOW) + (0x2000 >> 2)
-#define MY_PORT_ADDRESS(port,cardaddr) \
-	((cardaddr) + 0x200 - (port) * 0x100)
-
-#include "serial-card.c"

drivers/acorn/char/serial-card.c

-/*
- *  linux/drivers/acorn/char/serial-card.c
- *
- *  Copyright (C) 1996-1999 Russell King.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- * A generic handler of serial expansion cards that use 16550s or
- * the like.
- *
- * Definitions:
- *  MY_PRODS		Product numbers to identify this card by
- *  MY_MANUS		Manufacturer numbers to identify this card by
- *  MY_NUMPORTS		Number of ports per card
- *  MY_BAUD_BASE	Baud base for the card
- *  MY_INIT		Initialisation routine name
- *  MY_BASE_ADDRESS(ec)	Return base address for ports
- *  MY_PORT_ADDRESS
- *	(port,cardaddr)	Return address for port using base address
- *			from above.
- *
- * Changelog:
- *  30-07-1996	RMK	Created
- *  22-04-1998	RMK	Removed old register_pre_init_serial
- */
-#include <linux/module.h>
-#include <linux/types.h>
-#include <linux/serial.h>
-#include <linux/errno.h>
-#include <linux/ioport.h>
-#include <linux/init.h>
-
-#include <asm/ecard.h>
-#include <asm/string.h>
-
-#ifndef NUM_SERIALS
-#define NUM_SERIALS	MY_NUMPORTS * MAX_ECARDS
-#endif
-
-static int serial_ports[NUM_SERIALS];
-static int serial_pcount;
-static int serial_addr[NUM_SERIALS];
-static struct expansion_card *expcard[MAX_ECARDS];
-
-static const card_ids serial_cids[] = { MY_CARD_LIST, { 0xffff, 0xffff } };
-
-static inline int serial_register_onedev (unsigned long port, int irq)
-{
-	struct serial_struct req;
-
-	memset(&req, 0, sizeof(req));
-	req.baud_base = MY_BAUD_BASE;
-	req.irq = irq;
-	req.port = port;
-	req.flags = 0;
-
-	return register_serial(&req);
-}
-
-static int __init serial_card_init(void)
-{
-	int card = 0;
-
-	ecard_startfind ();
-
-	do {
-		struct expansion_card *ec;
-		unsigned long cardaddr;
-		int port;
-
-		ec = ecard_find (0, serial_cids);
-		if (!ec)
-			break;
-
-		cardaddr = MY_BASE_ADDRESS(ec);
-
-		for (port = 0; port < MY_NUMPORTS; port ++) {
-			unsigned long address;
-			int line;
-
-			address = MY_PORT_ADDRESS(port, cardaddr);
-
-			line = serial_register_onedev (address, ec->irq);
-			if (line < 0)
-				break;
-			serial_ports[serial_pcount] = line;
-			serial_addr[serial_pcount] = address;
-			serial_pcount += 1;
-		}
-
-		if (port) {
-			ecard_claim (ec);
-			expcard[card] = ec;
-		} else
-			break;
-	} while (++card < MAX_ECARDS);
-	return card ? 0 : -ENODEV;
-}
-
-static void __exit serial_card_exit(void)
-{
-	int i;
-
-	for (i = 0; i < serial_pcount; i++) {
-		unregister_serial(serial_ports[i]);
-		release_region(serial_addr[i], 8);
-	}
-
-	for (i = 0; i < MAX_ECARDS; i++)
-		if (expcard[i])
-			ecard_release (expcard[i]);
-}
-
-MODULE_AUTHOR("Russell King");
-MODULE_LICENSE("GPL");
-
-module_init(serial_card_init);
-module_exit(serial_card_exit);

drivers/acorn/net/ether1.c

@@ -43,6 +43,7 @@
 #include <linux/slab.h>
 #include <linux/string.h>
 #include <linux/errno.h>
+#include <linux/device.h>
 #include <linux/init.h>
 #include <linux/netdevice.h>
 #include <linux/etherdevice.h>
@@ -80,11 +81,6 @@ static char version[] __initdata = "ether1 ethernet driver (c) 2000 Russell King
 #define BUS_16 16
 #define BUS_8  8
 
-static const card_ids __init ether1_cids[] = {
-	{ MANU_ACORN, PROD_ACORN_ETHER1 },
-	{ 0xffff, 0xffff }
-};
-
 /* ------------------------------------------------------------------------- */
 
 #define DISABLEIRQS 1
@@ -647,6 +643,12 @@ ether1_open (struct net_device *dev)
 {
 	struct ether1_priv *priv = (struct ether1_priv *)dev->priv;
 
+	if (!is_valid_ether_addr(dev->dev_addr)) {
+		printk(KERN_WARNING "%s: invalid ethernet MAC address\n",
+			dev->name);
+		return -EINVAL;
+	}
+
 	if (request_irq(dev->irq, ether1_interrupt, 0, "ether1", dev))
 		return -EAGAIN;
 
@@ -971,6 +973,23 @@ ether1_getstats (struct net_device *dev)
 	return &priv->stats;
 }
 
+static int
+ether1_set_mac_address(struct net_device *dev, void *p)
+{
+	struct sockaddr *addr = p;
+
+	if (netif_running(dev))
+		return -EBUSY;
+
+	memcpy(dev->dev_addr, addr->sa_data, dev->addr_len);
+
+	/*
+	 * We'll set the MAC address on the chip when we open it.
+	 */
+
+	return 0;
+}
+
 /*
  * Set or clear the multicast filter for this adaptor.
  * num_addrs == -1	Promiscuous mode, receive all packets.
@@ -993,19 +1012,22 @@ static void __init ether1_banner(void)
 		printk(KERN_INFO "%s", version);
 }
 
-static struct net_device * __init ether1_init_one(struct expansion_card *ec)
+static int __devinit
+ether1_probe(struct expansion_card *ec, const struct ecard_id *id)
 {
 	struct net_device *dev;
 	struct ether1_priv *priv;
-	int i;
+	int i, ret = 0;
 
 	ether1_banner();
 
 	ecard_claim(ec);
 
 	dev = init_etherdev(NULL, sizeof(struct ether1_priv));
-	if (!dev)
+	if (!dev) {
+		ret = -ENOMEM;
 		goto out;
+	}
 
 	SET_MODULE_OWNER(dev);
 
@@ -1019,8 +1041,10 @@ static struct net_device * __init ether1_init_one(struct expansion_card *ec)
 	request_region(dev->base_addr + 0x800, 4096, dev->name);
 
 	priv = (struct ether1_priv *)dev->priv;
-	if ((priv->bus_type = ether1_reset(dev)) == 0)
+	if ((priv->bus_type = ether1_reset(dev)) == 0) {
+		ret = -ENODEV;
 		goto release;
+	}
 
 	printk(KERN_INFO "%s: ether1 in slot %d, ",
 		dev->name, ec->slot_no);
@@ -1030,16 +1054,21 @@ static struct net_device * __init ether1_init_one(struct expansion_card *ec)
 		printk ("%2.2x%c", dev->dev_addr[i], i == 5 ? '\n' : ':');
 	}
 
-	if (ether1_init_2(dev))
+	if (ether1_init_2(dev)) {
+		ret = -ENODEV;
 		goto release;
+	}
 
 	dev->open		= ether1_open;
 	dev->stop		= ether1_close;
 	dev->hard_start_xmit    = ether1_sendpacket;
 	dev->get_stats		= ether1_getstats;
 	dev->set_multicast_list = ether1_setmulticastlist;
+	dev->set_mac_address	= ether1_set_mac_address;
 	dev->tx_timeout		= ether1_timeout;
 	dev->watchdog_timeo	= 5 * HZ / 100;
+
+	ecard_set_drvdata(ec, dev);
 	return 0;
 
 release:
@@ -1049,55 +1078,46 @@ static struct net_device * __init ether1_init_one(struct expansion_card *ec)
 	kfree(dev);
 out:
 	ecard_release(ec);
-	return dev;
+	return ret;
 }
 
-static struct expansion_card	*e_card[MAX_ECARDS];
-static struct net_device	*e_dev[MAX_ECARDS];
-
-static int __init ether1_init(void)
+static void __devexit ether1_remove(struct expansion_card *ec)
 {
-	int i, ret = -ENODEV;
+	struct net_device *dev = ecard_get_drvdata(ec);
 
-	ecard_startfind();
+	ecard_set_drvdata(ec, NULL);	
 
-	for (i = 0; i < MAX_ECARDS; i++) {
-		struct expansion_card *ec;
-		struct net_device *dev;
+	unregister_netdev(dev);
 
-		ec = ecard_find(0, ether1_cids);
-		if (!ec)
-			break;
+	release_region(dev->base_addr, 16);
+	release_region(dev->base_addr + 0x800, 4096);
+	kfree(dev);
 
-		dev = ether1_init_one(ec);
-		if (!dev)
-			break;
+	ecard_release(ec);
+}
 
-		e_card[i] = ec;
-		e_dev[i]  = dev;
-		ret = 0;
-	}
+static const struct ecard_id ether1_ids[] = {
+	{ MANU_ACORN, PROD_ACORN_ETHER1 },
+	{ 0xffff, 0xffff }
+};
 
-	return ret;
+static struct ecard_driver ether1_driver = {
+	.probe		= ether1_probe,
+	.remove		= __devexit_p(ether1_remove),
+	.id_table	= ether1_ids,
+	.drv = {
+		.name	= "ether1",
+	},
+};
+
+static int __init ether1_init(void)
+{
+	return ecard_register_driver(&ether1_driver);
 }
 
 static void __exit ether1_exit(void)
 {
-	int i;
-
-	for (i = 0; i < MAX_ECARDS; i++) {
-		if (e_dev[i]) {
-			unregister_netdev(e_dev[i]);
-			release_region(e_dev[i]->base_addr, 16);
-			release_region(e_dev[i]->base_addr + 0x800, 4096);
-			kfree(e_dev[i]);
-			e_dev[i] = NULL;
-		}
-		if (e_card[i]) {
-			ecard_release(e_card[i]);
-			e_card[i] = NULL;
-		}
-	}
+	ecard_remove_driver(&ether1_driver);
 }
 
 module_init(ether1_init);

drivers/acorn/net/ether3.c

@@ -61,6 +61,7 @@
 #include <linux/netdevice.h>
 #include <linux/etherdevice.h>
 #include <linux/skbuff.h>
+#include <linux/device.h>
 #include <linux/init.h>
 #include <linux/delay.h>
 
@@ -75,12 +76,6 @@ static char version[] __initdata = "ether3 ethernet driver (c) 1995-2000 R.M.Kin
 #include "ether3.h"
 
 static unsigned int net_debug = NET_DEBUG;
-static const card_ids __init ether3_cids[] = {
-	{ MANU_ANT2, PROD_ANT_ETHER3 },
-	{ MANU_ANT,  PROD_ANT_ETHER3 },
-	{ MANU_ANT,  PROD_ANT_ETHERB },
-	{ 0xffff, 0xffff }
-};
 
 static void	ether3_setmulticastlist(struct net_device *dev);
 static int	ether3_rx(struct net_device *dev, struct dev_priv *priv, unsigned int maxcnt);
@@ -417,6 +412,12 @@ ether3_probe_bus_16(struct net_device *dev, int val)
 static int
 ether3_open(struct net_device *dev)
 {
+	if (!is_valid_ether_addr(dev->dev_addr)) {
+		printk(KERN_WARNING "%s: invalid ethernet MAC address\n",
+			dev->name);
+		return -EINVAL;
+	}
+
 	if (request_irq(dev->irq, ether3_interrupt, 0, "ether3", dev))
 		return -EAGAIN;
 
@@ -460,6 +461,23 @@ static struct net_device_stats *ether3_getstats(struct net_device *dev)
 	return &priv->stats;
 }
 
+static int
+ether3_set_mac_address(struct net_device *dev, void *p)
+{
+	struct sockaddr *addr = p;
+
+	if (netif_running(dev))
+		return -EBUSY;
+
+	memcpy(dev->dev_addr, addr->sa_data, dev->addr_len);
+
+	/*
+	 * We'll set the MAC address on the chip when we open it.
+	 */
+
+	return 0;
+}
+
 /*
  * Set or clear promiscuous/multicast mode filter for this adaptor.
  *
@@ -784,6 +802,7 @@ static const char * __init
 ether3_get_dev(struct net_device *dev, struct expansion_card *ec)
 {
 	const char *name = "ether3";
+
 	dev->base_addr = ecard_address(ec, ECARD_MEMC, 0);
 	dev->irq = ec->irq;
 
@@ -796,38 +815,44 @@ ether3_get_dev(struct net_device *dev, struct expansion_card *ec)
 	ec->irqaddr = (volatile unsigned char *)ioaddr(dev->base_addr);
 	ec->irqmask = 0xf0;
 
-	if (ether3_addr(dev->dev_addr, ec))
-		name = NULL;
+	ether3_addr(dev->dev_addr, ec);
 
 	return name;
 }
 
-static struct net_device * __init ether3_init_one(struct expansion_card *ec)
+static int __devinit
+ether3_probe(struct expansion_card *ec, const struct ecard_id *id)
 {
 	struct net_device *dev;
 	struct dev_priv *priv;
 	const char *name;
-	int i, bus_type;
+	int i, bus_type, ret;
 
 	ether3_banner();
 
 	ecard_claim(ec);
 
 	dev = init_etherdev(NULL, sizeof(struct dev_priv));
-	if (!dev)
+	if (!dev) {
+		ret = -ENOMEM;
 		goto out;
+	}
 
 	SET_MODULE_OWNER(dev);
 
 	name = ether3_get_dev(dev, ec);
-	if (!name)
+	if (!name) {
+		ret = -ENODEV;
 		goto free;
+	}
 
 	/*
 	 * this will not fail - the nature of the bus ensures this
 	 */
-	if (!request_region(dev->base_addr, 128, dev->name))
+	if (!request_region(dev->base_addr, 128, dev->name)) {
+		ret = -EBUSY;
 		goto free;
+	}
 
 	priv = (struct dev_priv *) dev->priv;
 
@@ -852,11 +877,13 @@ static struct net_device * __init ether3_init_one(struct expansion_card *ec)
 	switch (bus_type) {
 	case BUS_UNKNOWN:
 		printk(KERN_ERR "%s: unable to identify bus width\n", dev->name);
+		ret = -ENODEV;
 		goto failed;
 
 	case BUS_8:
 		printk(KERN_ERR "%s: %s found, but is an unsupported "
 			"8-bit card\n", dev->name, name);
+		ret = -ENODEV;
 		goto failed;
 
 	default:
@@ -867,16 +894,21 @@ static struct net_device * __init ether3_init_one(struct expansion_card *ec)
 	for (i = 0; i < 6; i++)
 		printk("%2.2x%c", dev->dev_addr[i], i == 5 ? '\n' : ':');
 
-	if (ether3_init_2(dev))
+	if (ether3_init_2(dev)) {
+		ret = -ENODEV;
 		goto failed;
+	}
 
 	dev->open		= ether3_open;
 	dev->stop		= ether3_close;
 	dev->hard_start_xmit	= ether3_sendpacket;
 	dev->get_stats		= ether3_getstats;
 	dev->set_multicast_list	= ether3_setmulticastlist;
+	dev->set_mac_address	= ether3_set_mac_address;
 	dev->tx_timeout		= ether3_timeout;
 	dev->watchdog_timeo	= 5 * HZ / 100;
+
+	ecard_set_drvdata(ec, dev);
 	return 0;
 
 failed:
@@ -886,54 +918,46 @@ static struct net_device * __init ether3_init_one(struct expansion_card *ec)
 	kfree(dev);
 out:
 	ecard_release(ec);
-	return NULL;
+	return ret;
 }
 
-static struct expansion_card	*e_card[MAX_ECARDS];
-static struct net_device	*e_dev[MAX_ECARDS];
-
-static int ether3_init(void)
+static void __devexit ether3_remove(struct expansion_card *ec)
 {
-	int i, ret = -ENODEV;
+	struct net_device *dev = ecard_get_drvdata(ec);
 
-	ecard_startfind();
+	ecard_set_drvdata(ec, NULL);
 
-	for (i = 0; i < MAX_ECARDS; i++) {
-		struct net_device *dev;
-		struct expansion_card *ec;
+	unregister_netdev(dev);
+	release_region(dev->base_addr, 128);
+	kfree(dev);
 
-		ec = ecard_find(0, ether3_cids);
-		if (!ec)
-			break;
+	ecard_release(ec);
+}
 
-		dev = ether3_init_one(ec);
-		if (!dev)
-			break;
+static const struct ecard_id ether3_ids[] = {
+	{ MANU_ANT2, PROD_ANT_ETHER3 },
+	{ MANU_ANT,  PROD_ANT_ETHER3 },
+	{ MANU_ANT,  PROD_ANT_ETHERB },
+	{ 0xffff, 0xffff }
+};
 
-		e_card[i] = ec;
-		e_dev[i]  = dev;
-		ret = 0;
-	}
+static struct ecard_driver ether3_driver = {
+	.probe		= ether3_probe,
+	.remove		= __devexit_p(ether3_remove),
+	.id_table	= ether3_ids,
+	.drv = {
+		.name	= "ether3",
+	},
+};
 
-	return ret;
+static int __init ether3_init(void)
+{
+	return ecard_register_driver(&ether3_driver);
 }
 
-static void ether3_exit(void)
+static void __exit ether3_exit(void)
 {
-	int i;
-
-	for (i = 0; i < MAX_ECARDS; i++) {
-		if (e_dev[i]) {
-			unregister_netdev(e_dev[i]);
-			release_region(e_dev[i]->base_addr, 128);
-			kfree(e_dev[i]);
-			e_dev[i] = NULL;
-		}
-		if (e_card[i]) {
-			ecard_release(e_card[i]);
-			e_card[i] = NULL;
-		}
-	}
+	ecard_remove_driver(&ether3_driver);
 }
 
 module_init(ether3_init);

drivers/acorn/net/etherh.c

@@ -42,6 +42,7 @@
 #include <linux/etherdevice.h>
 #include <linux/skbuff.h>
 #include <linux/delay.h>
+#include <linux/device.h>
 #include <linux/init.h>
 
 #include <asm/system.h>
@@ -57,14 +58,6 @@
 
 static unsigned int net_debug = NET_DEBUG;
 
-static const card_ids __init etherh_cids[] = {
-	{ MANU_ANT, PROD_ANT_ETHERM      },
-	{ MANU_I3,  PROD_I3_ETHERLAN500  },
-	{ MANU_I3,  PROD_I3_ETHERLAN600  },
-	{ MANU_I3,  PROD_I3_ETHERLAN600A },
-	{ 0xffff,   0xffff }
-};
-
 struct etherh_priv {
 	struct ei_device eidev;
 	unsigned int	id;
@@ -441,6 +434,12 @@ etherh_open(struct net_device *dev)
 {
 	struct ei_device *ei_local = (struct ei_device *) dev->priv;
 
+	if (!is_valid_ether_addr(dev->dev_addr)) {
+		printk(KERN_WARNING "%s: invalid ethernet MAC address\n",
+			dev->name);
+		return -EINVAL;
+	}
+
 	if (request_irq(dev->irq, ei_interrupt, 0, dev->name, dev))
 		return -EAGAIN;
 
@@ -483,6 +482,23 @@ etherh_close(struct net_device *dev)
 	return 0;
 }
 
+static int
+etherh_set_mac_address(struct net_device *dev, void *p)
+{
+	struct sockaddr *addr = p;
+
+	if (netif_running(dev))
+		return -EBUSY;
+
+	memcpy(dev->dev_addr, addr->sa_data, dev->addr_len);
+
+	/*
+	 * We'll set the MAC address on the chip when we open it.
+	 */
+
+	return 0;
+}
+
 /*
  * Initialisation
  */
@@ -541,21 +557,24 @@ static int __init etherm_addr(char *addr)
 static u32 etherh_regoffsets[16];
 static u32 etherm_regoffsets[16];
 
-static struct net_device * __init etherh_init_one(struct expansion_card *ec)
+static int __init
+etherh_probe(struct expansion_card *ec, const struct ecard_id *id)
 {
 	struct ei_device *ei_local;
 	struct net_device *dev;
 	struct etherh_priv *eh;
 	const char *dev_type;
-	int i, size;
+	int i, size, ret;
 
 	etherh_banner();
 
 	ecard_claim(ec);
 	
 	dev = init_etherdev(NULL, sizeof(struct etherh_priv));
-	if (!dev)
+	if (!dev) {
+		ret = -ENOMEM;
 		goto out;
+	}
 
 	/*
 	 * init_etherdev allocs and zeros dev->priv
@@ -568,31 +587,31 @@ static struct net_device * __init etherh_init_one(struct expansion_card *ec)
 
 	dev->open		= etherh_open;
 	dev->stop		= etherh_close;
+	dev->set_mac_address	= etherh_set_mac_address;
 	dev->set_config		= etherh_set_config;
 	dev->irq		= ec->irq;
 	dev->base_addr		= ecard_address(ec, ECARD_MEMC, 0);
-	dev->priv	= eh;
 
 	/*
 	 * IRQ and control port handling
 	 */
+	if (ec->irq != 11) {
 		ec->ops		= &etherh_ops;
 		ec->irq_data	= eh;
+	}
 	eh->ctrl		= 0;
 	eh->id			= ec->cid.product;
 
 	switch (ec->cid.product) {
 	case PROD_ANT_ETHERM:
-		if (etherm_addr(dev->dev_addr))
-			goto free;
+		etherm_addr(dev->dev_addr);
 		dev->base_addr += ETHERM_NS8390;
 		dev->mem_start  = dev->base_addr + ETHERM_DATAPORT;
 		eh->ctrl_port   = dev->base_addr + ETHERM_CTRLPORT;
 		break;
 
 	case PROD_I3_ETHERLAN500:
-		if (etherh_addr(dev->dev_addr, ec))
-			goto free;
+		etherh_addr(dev->dev_addr, ec);
 		dev->base_addr += ETHERH500_NS8390;
 		dev->mem_start  = dev->base_addr + ETHERH500_DATAPORT;
 		eh->ctrl_port   = ecard_address (ec, ECARD_IOC, ECARD_FAST)
@@ -601,8 +620,7 @@ static struct net_device * __init etherh_init_one(struct expansion_card *ec)
 
 	case PROD_I3_ETHERLAN600:
 	case PROD_I3_ETHERLAN600A:
-		if (etherh_addr(dev->dev_addr, ec))
-			goto free;
+		etherh_addr(dev->dev_addr, ec);
 		dev->base_addr += ETHERH600_NS8390;
 		dev->mem_start  = dev->base_addr + ETHERH600_DATAPORT;
 		eh->ctrl_port   = dev->base_addr + ETHERH600_CTRLPORT;
@@ -611,6 +629,7 @@ static struct net_device * __init etherh_init_one(struct expansion_card *ec)
 	default:
 		printk(KERN_ERR "%s: unknown card type %x\n",
 		       dev->name, ec->cid.product);
+		ret = -ENODEV;
 		goto free;
 	}
 
@@ -618,11 +637,15 @@ static struct net_device * __init etherh_init_one(struct expansion_card *ec)
 	if (ec->cid.product == PROD_ANT_ETHERM)
 		size <<= 3;
 
-	if (!request_region(dev->base_addr, size, dev->name))
+	if (!request_region(dev->base_addr, size, dev->name)) {
+		ret = -EBUSY;
 		goto free;
+	}
 
-	if (ethdev_init(dev))
+	if (ethdev_init(dev)) {
+		ret = -ENODEV;
 		goto release;
+	}
 
 	/*
 	 * If we're in the NIC slot, make sure the IRQ is enabled
@@ -690,7 +713,10 @@ static struct net_device * __init etherh_init_one(struct expansion_card *ec)
 
 	etherh_reset(dev);
 	NS8390_init(dev, 0);
-	return dev;
+
+	ecard_set_drvdata(ec, dev);
+
+	return 0;
 
 release:
 	release_region(dev->base_addr, 16);
@@ -700,67 +726,59 @@ static struct net_device * __init etherh_init_one(struct expansion_card *ec)
 	kfree(dev);
 out:
 	ecard_release(ec);
-	return NULL;
+	return ret;
 }
 
-#define MAX_ETHERH_CARDS 2
+static void __devexit etherh_remove(struct expansion_card *ec)
+{
+	struct net_device *dev = ecard_get_drvdata(ec);
+	int size = 16;
 
-static struct net_device *e_dev[MAX_ETHERH_CARDS];
-static struct expansion_card *e_card[MAX_ETHERH_CARDS];
+	ecard_set_drvdata(ec, NULL);
+
+	unregister_netdev(dev);
+	if (ec->cid.product == PROD_ANT_ETHERM)
+		size <<= 3;
+	release_region(dev->base_addr, size);
+	kfree(dev);
+
+	ec->ops = NULL;
+	kfree(ec->irq_data);
+	ecard_release(ec);
+}
+
+static const struct ecard_id etherh_ids[] = {
+	{ MANU_ANT, PROD_ANT_ETHERM      },
+	{ MANU_I3,  PROD_I3_ETHERLAN500  },
+	{ MANU_I3,  PROD_I3_ETHERLAN600  },
+	{ MANU_I3,  PROD_I3_ETHERLAN600A },
+	{ 0xffff,   0xffff }
+};
+
+static struct ecard_driver etherh_driver = {
+	.probe		= etherh_probe,
+	.remove		= __devexit_p(etherh_remove),
+	.id_table	= etherh_ids,
+	.drv = {
+		.name	= "etherh",
+	},
+};
 
 static int __init etherh_init(void)
 {
-	int i, ret = -ENODEV;
+	int i;
 
 	for (i = 0; i < 16; i++) {
 		etherh_regoffsets[i] = i;
 		etherm_regoffsets[i] = i << 3;
 	}
 
-	ecard_startfind();
-
-	for (i = 0; i < MAX_ECARDS; i++) {
-		struct expansion_card *ec;
-		struct net_device *dev;
-
-		ec = ecard_find(0, etherh_cids);
-		if (!ec)
-			break;
-
-		dev = etherh_init_one(ec);
-		if (!dev)
-			break;
-
-		e_card[i] = ec;
-		e_dev[i]  = dev;
-		ret = 0;
-	}
-
-	return ret;
+	return ecard_register_driver(&etherh_driver);
 }
 
 static void __exit etherh_exit(void)
 {
-	int i;
-
-	for (i = 0; i < MAX_ETHERH_CARDS; i++) {
-		if (e_dev[i]) {
-			int size;
-			unregister_netdev(e_dev[i]);
-			size = 16;
-			if (e_card[i]->cid.product == PROD_ANT_ETHERM)
-				size <<= 3;
-			release_region(e_dev[i]->base_addr, size);
-			kfree(e_dev[i]);
-			e_dev[i] = NULL;
-		}
-		if (e_card[i]) {
-			e_card[i]->ops = NULL;
-			kfree(e_card[i]->irq_data);
-			ecard_release(e_card[i]);
-			e_card[i] = NULL;
-		}
-	}
+	ecard_remove_driver(&etherh_driver);
 }
 
 module_init(etherh_init);

drivers/acorn/scsi/acornscsi.c

@@ -319,12 +319,12 @@ acornscsi_csdelay(unsigned int cs)
 
     target_jiffies = jiffies + 1 + cs * HZ / 100;
 
-    save_flags(flags);
-    sti();
+    local_save_flags(flags);
+    local_irq_enable();
 
     while (time_before(jiffies, target_jiffies)) barrier();
 
-    restore_flags(flags);
+    local_irq_restore(flags);
 }
 
 static
@@ -403,8 +403,9 @@ void acornscsi_resetcard(AS_Host *host)
     host->scsi.phase = PHASE_IDLE;
     host->scsi.disconnectable = 0;
 
+    memset(host->busyluns, 0, sizeof(host->busyluns));
+
     for (i = 0; i < 8; i++) {
-	host->busyluns[i] = 0;
 	host->device[i].sync_state = SYNC_NEGOCIATE;
 	host->device[i].disconnect_ok = 1;
     }
@@ -1593,7 +1594,7 @@ void acornscsi_message(AS_Host *host)
 	    printk(KERN_NOTICE "scsi%d.%c: disabling tagged queueing\n",
 		    host->host->host_no, acornscsi_target(host));
 	    host->SCpnt->device->tagged_queue = 0;
-	    set_bit(host->SCpnt->target * 8 + host->SCpnt->lun, &host->busyluns);
+	    set_bit(host->SCpnt->target * 8 + host->SCpnt->lun, host->busyluns);
 	    break;
 #endif
 	case EXTENDED_MESSAGE | (EXTENDED_SDTR << 8):
@@ -2637,8 +2638,7 @@ acornscsi_do_abort(AS_Host *host, Scsi_Cmnd *SCpnt)
 		printk("executing ");
 //#endif
 
-		save_flags(flags);
-		cli();
+		local_irq_save(flags);
 		switch (host->scsi.phase) {
 		/*
 		 * If the interface is idle, and the command is 'disconnectable',
@@ -2671,7 +2671,7 @@ acornscsi_do_abort(AS_Host *host, Scsi_Cmnd *SCpnt)
 			acornscsi_abortcmd(host, host->SCpnt->tag);
 			res = res_snooze;
 		}
-		restore_flags(flags);
+		local_irq_restore(flags);
 	} else if (host->origSCpnt == SCpnt) {
 		/*
 		 * The command will be executed next, but a command

drivers/acorn/scsi/acornscsi.h

@@ -326,7 +326,7 @@ typedef struct acornscsi_hostdata {
 	syncxfer_t	sync_state;		/* sync xfer negociation state		*/
 	unsigned char	disconnect_ok:1;	/* device can disconnect		*/
     } device[8];
-    unsigned char	busyluns[8];		/* array of bits indicating LUNs busy	*/
+    unsigned long	busyluns[64 / sizeof(unsigned long)];/* array of bits indicating LUNs busy	*/
 
     /* DMA info */
     struct {

drivers/acorn/scsi/cumana_1.c

@@ -83,10 +83,8 @@ static const card_ids cumanascsi_cids[] = {
 #define NCR5380_read(reg) cumanascsi_read(_instance, reg)
 #define NCR5380_write(reg, value) cumanascsi_write(_instance, reg, value)
 
-#define do_NCR5380_intr do_cumanascsi_intr
+#define NCR5380_intr		cumanascsi_intr
 #define NCR5380_queue_command	cumanascsi_queue_command
-#define NCR5380_abort cumanascsi_abort
-#define NCR5380_reset cumanascsi_reset
 #define NCR5380_proc_info	cumanascsi_proc_info
 
 int NCR5380_proc_info(char *buffer, char **start, off_t offset,
@@ -159,7 +157,7 @@ int cumanascsi_detect(Scsi_Host_Template * tpnt)
         outb(0x00, instance->io_port - 577);
 
 	if (instance->irq != IRQ_NONE)
-	    if (request_irq(instance->irq, do_cumanascsi_intr, SA_INTERRUPT, "CumanaSCSI-1", NULL)) {
+	    if (request_irq(instance->irq, cumanascsi_intr, SA_INTERRUPT, "CumanaSCSI-1", NULL)) {
 		printk("scsi%d: IRQ%d not free, interrupts disabled\n",
 		    instance->host_no, instance->irq);
 		instance->irq = IRQ_NONE;
@@ -401,8 +399,10 @@ static Scsi_Host_Template cumanascsi_template = {
 	.release		= cumanascsi_release,
 	.info			= cumanascsi_info,
 	.queuecommand		= cumanascsi_queue_command,
-	.abort			= cumanascsi_abort,
-	.reset			= cumanascsi_reset,
+	.eh_abort_handler	= NCR5380_abort,
+	.eh_device_reset_handler= NCR5380_device_reset,
+	.eh_bus_reset_handler	= NCR5380_bus_reset,
+	.eh_host_reset_handler	= NCR5380_host_reset,
 	.bios_param		= scsicam_bios_param,
 	.can_queue		= 16,
 	.this_id		= 7,

drivers/acorn/scsi/ecoscsi.c

@@ -248,10 +248,8 @@ printk("reading %p len %d\n",addr, len);
 #define NCR5380_read(reg) ecoscsi_read(_instance, reg)
 #define NCR5380_write(reg, value) ecoscsi_write(_instance, reg, value)
 
-#define do_NCR5380_intr do_ecoscsi_intr
+#define NCR5380_intr		ecoscsi_intr
 #define NCR5380_queue_command	ecoscsi_queue_command
-#define NCR5380_abort ecoscsi_abort
-#define NCR5380_reset ecoscsi_reset
 #define NCR5380_proc_info	ecoscsi_proc_info
 
 int NCR5380_proc_info(char *buffer, char **start, off_t offset,
@@ -269,8 +267,10 @@ static Scsi_Host_Template ecoscsi_template =  {
 	.release	= ecoscsi_release,
 	.info		= ecoscsi_info,
 	.queuecommand	= ecoscsi_queue_command,
-	.abort		= ecoscsi_abort,
-	.reset		= ecoscsi_reset,
+	.eh_abort_handler	= NCR5380_abort,
+	.eh_device_reset_handler= NCR5380_device_reset,
+	.eh_bus_reset_handler	= NCR5380_bus_reset,
+	.eh_host_reset_handler	= NCR5380_host_reset,
 	.can_queue	= 16,
 	.this_id	= 7,
 	.sg_tablesize	= SG_ALL,

drivers/acorn/scsi/fas216.c

@@ -603,7 +603,7 @@ fas216_updateptrs(FAS216_Info *info, int bytes_transferred)
 		 * next buffer.
 		 */
 		bytes_transferred -= SCp->this_residual;
-		if (!next_SCp(&info->scsi.SCp)) {
+		if (!next_SCp(&info->scsi.SCp) && bytes_transferred) {
 			printk(KERN_WARNING "scsi%d.%c: out of buffers\n",
 				info->host->host_no, '0' + info->SCpnt->target);
 			return;
@@ -2300,8 +2300,8 @@ int fas216_eh_device_reset(Scsi_Cmnd *SCpnt)
 {
 	FAS216_Info *info = (FAS216_Info *)SCpnt->host->hostdata;
 
-	printk("scsi%d.%c: "__FUNCTION__": called\n",
-		info->host->host_no, '0' + SCpnt->target);
+	printk("scsi%d.%c: %s: called\n",
+		info->host->host_no, '0' + SCpnt->target, __FUNCTION__);
 	return FAILED;
 }
 
@@ -2320,8 +2320,8 @@ int fas216_eh_bus_reset(Scsi_Cmnd *SCpnt)
 
 	info->stats.bus_resets += 1;
 
-	printk("scsi%d.%c: "__FUNCTION__": resetting bus\n",
-		info->host->host_no, '0' + SCpnt->target);
+	printk("scsi%d.%c: %s: resetting bus\n",
+		info->host->host_no, '0' + SCpnt->target, __FUNCTION__);
 
 	/*
 	 * Attempt to stop all activity on this interface.
@@ -2381,8 +2381,8 @@ int fas216_eh_host_reset(Scsi_Cmnd *SCpnt)
 
 	fas216_checkmagic(info);
 
-	printk("scsi%d.%c: "__FUNCTION__": resetting host\n",
-		info->host->host_no, '0' + SCpnt->target);
+	printk("scsi%d.%c: %s: resetting host\n",
+		info->host->host_no, '0' + SCpnt->target, __FUNCTION__);
 
 	/*
 	 * Reset the SCSI chip.

drivers/acorn/scsi/fas216.h

@@ -288,7 +288,7 @@ typedef struct {
 		neg_t		sync_state;		/* synchronous transfer mode		*/
 		neg_t		wide_state;		/* wide transfer mode			*/
 	} device[8];
-	unsigned char	busyluns[8];			/* array of bits indicating LUNs busy	*/
+	unsigned long	busyluns[64/sizeof(unsigned long)];/* array of bits indicating LUNs busy	*/
 
 	/* dma */
 	struct {

drivers/acorn/scsi/oak.c

@@ -64,10 +64,8 @@
 
 #define NCR5380_read(reg)		oakscsi_read(_instance, reg)
 #define NCR5380_write(reg, value)	oakscsi_write(_instance, reg, value)
-#define do_NCR5380_intr			do_oakscsi_intr
+#define NCR5380_intr			oakscsi_intr
 #define NCR5380_queue_command		oakscsi_queue_command
-#define NCR5380_abort			oakscsi_abort
-#define NCR5380_reset			oakscsi_reset
 #define NCR5380_proc_info		oakscsi_proc_info
 
 int NCR5380_proc_info(char *buffer, char **start, off_t offset,
@@ -142,7 +140,7 @@ int oakscsi_detect(Scsi_Host_Template * tpnt)
 	}
 
 	if (instance->irq != IRQ_NONE)
-	    if (request_irq(instance->irq, do_oakscsi_intr, SA_INTERRUPT, "Oak SCSI", NULL)) {
+	    if (request_irq(instance->irq, oakscsi_intr, SA_INTERRUPT, "Oak SCSI", NULL)) {
 		printk("scsi%d: IRQ%d not free, interrupts disabled\n",
 		    instance->host_no, instance->irq);
 		instance->irq = IRQ_NONE;
@@ -264,8 +262,10 @@ static Scsi_Host_Template oakscsi_template = {
 	.release	= oakscsi_release,
 	.info		= oakscsi_info,
 	.queuecommand	= oakscsi_queue_command,
-	.abort		= oakscsi_abort,
-	.reset		= oakscsi_reset,
+	.eh_abort_handler	= NCR5380_abort,
+	.eh_device_reset_handler= NCR5380_device_reset,
+	.eh_bus_reset_handler	= NCR5380_bus_reset,
+	.eh_host_reset_handler	= NCR5380_host_reset,
 	.can_queue	= 16,
 	.this_id	= 7,
 	.sg_tablesize	= SG_ALL,

drivers/acorn/scsi/queue.c

@@ -161,7 +161,7 @@ static Scsi_Cmnd *__queue_remove(Queue_t *queue, struct list_head *ent)
  *	     exclude - bit array of target&lun which is busy
  * Returns : Scsi_Cmnd if successful (and a reference), or NULL if no command available
  */
-Scsi_Cmnd *queue_remove_exclude(Queue_t *queue, void *exclude)
+Scsi_Cmnd *queue_remove_exclude(Queue_t *queue, unsigned long *exclude)
 {
 	unsigned long flags;
 	struct list_head *l;

drivers/acorn/scsi/queue.h

@@ -46,7 +46,7 @@ extern Scsi_Cmnd *queue_remove (Queue_t *queue);
  *	     exclude - array of busy LUNs
  * Returns : Scsi_Cmnd if successful (and a reference), or NULL if no command available
  */
-extern Scsi_Cmnd *queue_remove_exclude (Queue_t *queue, void *exclude);
+extern Scsi_Cmnd *queue_remove_exclude (Queue_t *queue, unsigned long *exclude);
 
 #define queue_add_cmd_ordered(queue,SCpnt) \
 	__queue_add(queue,SCpnt,(SCpnt)->cmnd[0] == REQUEST_SENSE)

drivers/acorn/scsi/scsi.h

@@ -51,7 +51,7 @@ static inline int next_SCp(Scsi_Pointer *SCp)
 
 static inline unsigned char get_next_SCp_byte(Scsi_Pointer *SCp)
 {
-	char c = SCp->ptr;
+	char c = *SCp->ptr;
 
 	SCp->ptr += 1;
 	SCp->this_residual -= 1;
@@ -63,7 +63,7 @@ static inline unsigned char get_next_SCp_byte(Scsi_Pointer *SCp)
 
 static inline void put_next_SCp_byte(Scsi_Pointer *SCp, unsigned char c)
 {
-	SCp->ptr = c;
+	*SCp->ptr = c;
 	SCp->ptr += 1;
 	SCp->this_residual -= 1;
 	if (SCp->this_residual == 0)

drivers/mtd/afs.c

@@ -21,7 +21,7 @@
    This is access code for flashes using ARM's flash partitioning 
    standards.
 
-   $Id: afs.c,v 1.6 2001/10/02 10:04:51 rmk Exp $
+   $Id: afs.c,v 1.8 2002/05/04 08:49:09 rmk Exp $
 
 ======================================================================*/
 
@@ -82,6 +82,12 @@ afs_read_footer(struct mtd_info *mtd, u_int *img_start, u_int *iis_start,
 	if (fs.signature != 0xa0ffff9f)
 		ret = 1;
 
+	/*
+	 * Don't touch the SIB.
+	 */
+	if (fs.type == 2)
+		ret = 1;
+
 	*iis_start = fs.image_info_base & mask;
 	*img_start = fs.image_start & mask;
 
@@ -163,6 +169,7 @@ int parse_afs_partitions(struct mtd_info *mtd, struct mtd_partition **pparts)
 	if (!parts)
 		return -ENOMEM;
 
+	memset(parts, 0, sz);
 	str = (char *)(parts + idx);
 
 	/*

drivers/mtd/maps/integrator-flash.c

@@ -21,7 +21,7 @@
    This is access code for flashes using ARM's flash partitioning 
    standards.
 
-   $Id: integrator-flash.c,v 1.6 2001/10/02 16:00:01 dwmw2 Exp $
+   $Id: integrator-flash.c,v 1.7 2001/11/01 20:55:47 rmk Exp $
 
 ======================================================================*/
 
@@ -208,10 +208,10 @@ static struct map_info armflash_map =
 };
 
 static struct mtd_info *mtd;
+static struct mtd_partition *parts;
 
 static int __init armflash_cfi_init(void *base, u_int size)
 {
-	struct mtd_partition *parts;
 	int ret;
 
 	armflash_flash_init();
@@ -238,8 +238,6 @@ static int __init armflash_cfi_init(void *base, u_int size)
 	ret = parse_afs_partitions(mtd, &parts);
 	if (ret > 0) {
 		ret = add_mtd_partitions(mtd, parts, ret);
-		/* we don't need the partition info any longer */
-		kfree(parts);
 		if (ret)
 			printk(KERN_ERR "mtd partition registration "
 				"failed: %d\n", ret);
@@ -262,6 +260,8 @@ static void armflash_cfi_exit(void)
 		del_mtd_partitions(mtd);
 		map_destroy(mtd);
 	}
+	if (parts)
+		kfree(parts);
 }
 
 static int __init armflash_init(void)

drivers/pcmcia/sa1100_adsbitsy.c

@@ -84,14 +84,14 @@ adsbitsy_pcmcia_configure_socket(const struct pcmcia_configure *conf)
 }
 
 static struct pcmcia_low_level adsbitsy_pcmcia_ops = {
-  init:			adsbitsy_pcmcia_init,
-  shutdown:		sa1111_pcmcia_shutdown,
-  socket_state:		sa1111_pcmcia_socket_state,
-  get_irq_info:		sa1111_pcmcia_get_irq_info,
-  configure_socket:	adsbitsy_pcmcia_configure_socket,
-
-  socket_init:		sa1111_pcmcia_socket_init,
-  socket_suspend:	sa1111_pcmcia_socket_suspend,
+  .init			= adsbitsy_pcmcia_init,
+  .shutdown		= sa1111_pcmcia_shutdown,
+  .socket_state		= sa1111_pcmcia_socket_state,
+  .get_irq_info		= sa1111_pcmcia_get_irq_info,
+  .configure_socket	= adsbitsy_pcmcia_configure_socket,
+
+  .socket_init		= sa1111_pcmcia_socket_init,
+  .socket_suspend	= sa1111_pcmcia_socket_suspend,
 };
 
 int __init pcmcia_adsbitsy_init(void)

drivers/pcmcia/sa1100_assabet.c

@@ -11,6 +11,7 @@
 #include <linux/init.h>
 
 #include <asm/hardware.h>
+#include <asm/mach-types.h>
 #include <asm/irq.h>
 #include <asm/arch/assabet.h>
 
@@ -192,14 +193,14 @@ static int assabet_pcmcia_socket_suspend(int sock)
 }
 
 static struct pcmcia_low_level assabet_pcmcia_ops = { 
-	init:			assabet_pcmcia_init,
-	shutdown:		assabet_pcmcia_shutdown,
-	socket_state:		assabet_pcmcia_socket_state,
-	get_irq_info:		assabet_pcmcia_get_irq_info,
-	configure_socket:	assabet_pcmcia_configure_socket,
-
-	socket_init:		assabet_pcmcia_socket_init,
-	socket_suspend:		assabet_pcmcia_socket_suspend,
+	.init			= assabet_pcmcia_init,
+	.shutdown		= assabet_pcmcia_shutdown,
+	.socket_state		= assabet_pcmcia_socket_state,
+	.get_irq_info		= assabet_pcmcia_get_irq_info,
+	.configure_socket	= assabet_pcmcia_configure_socket,
+
+	.socket_init		= assabet_pcmcia_socket_init,
+	.socket_suspend		= assabet_pcmcia_socket_suspend,
 };
 
 int __init pcmcia_assabet_init(void)

drivers/pcmcia/sa1100_badge4.c

@@ -146,14 +146,14 @@ badge4_pcmcia_configure_socket(const struct pcmcia_configure *conf)
 }
 
 static struct pcmcia_low_level badge4_pcmcia_ops = {
-	init:			badge4_pcmcia_init,
-	shutdown:		badge4_pcmcia_shutdown,
-	socket_state:		sa1111_pcmcia_socket_state,
-	get_irq_info:		sa1111_pcmcia_get_irq_info,
-	configure_socket:	badge4_pcmcia_configure_socket,
-
-	socket_init:		sa1111_pcmcia_socket_init,
-	socket_suspend:		sa1111_pcmcia_socket_suspend,
+	.init			= badge4_pcmcia_init,
+	.shutdown		= badge4_pcmcia_shutdown,
+	.socket_state		= sa1111_pcmcia_socket_state,
+	.get_irq_info		= sa1111_pcmcia_get_irq_info,
+	.configure_socket	= badge4_pcmcia_configure_socket,
+
+	.socket_init		= sa1111_pcmcia_socket_init,
+	.socket_suspend		= sa1111_pcmcia_socket_suspend,
 };
 
 int __init pcmcia_badge4_init(void)

drivers/pcmcia/sa1100_cerf.c

@@ -11,6 +11,7 @@
 #include <linux/init.h>
 
 #include <asm/hardware.h>
+#include <asm/mach-types.h>
 #include <asm/irq.h>
 #include "sa1100_generic.h"
 
@@ -160,14 +161,14 @@ static int cerf_pcmcia_socket_suspend(int sock)
 }
 
 static struct pcmcia_low_level cerf_pcmcia_ops = { 
-  init:			cerf_pcmcia_init,
-  shutdown:		cerf_pcmcia_shutdown,
-  socket_state:		cerf_pcmcia_socket_state,
-  get_irq_info:		cerf_pcmcia_get_irq_info,
-  configure_socket:	cerf_pcmcia_configure_socket,
-
-  socket_init:		cerf_pcmcia_socket_init,
-  socket_suspend:	cerf_pcmcia_socket_suspend,
+  .init			= cerf_pcmcia_init,
+  .shutdown		= cerf_pcmcia_shutdown,
+  .socket_state		= cerf_pcmcia_socket_state,
+  .get_irq_info		= cerf_pcmcia_get_irq_info,
+  .configure_socket	= cerf_pcmcia_configure_socket,
+
+  .socket_init		= cerf_pcmcia_socket_init,
+  .socket_suspend	= cerf_pcmcia_socket_suspend,
 };
 
 int __init pcmcia_cerf_init(void)

drivers/pcmcia/sa1100_flexanet.c

@@ -11,6 +11,7 @@
 #include <linux/init.h>
 
 #include <asm/hardware.h>
+#include <asm/mach-types.h>
 #include <asm/irq.h>
 #include "sa1100_generic.h"
 
@@ -221,14 +222,14 @@ static int flexanet_pcmcia_socket_suspend(int sock)
  *
  */
 static struct pcmcia_low_level flexanet_pcmcia_ops = {
-  init:			flexanet_pcmcia_init,
-  shutdown:		flexanet_pcmcia_shutdown,
-  socket_state:		flexanet_pcmcia_socket_state,
-  get_irq_info:		flexanet_pcmcia_get_irq_info,
-  configure_socket:	flexanet_pcmcia_configure_socket,
-
-  socket_init:		flexanet_pcmcia_socket_init,
-  socket_suspend:	flexanet_pcmcia_socket_suspend,
+  .init			= flexanet_pcmcia_init,
+  .shutdown		= flexanet_pcmcia_shutdown,
+  .socket_state		= flexanet_pcmcia_socket_state,
+  .get_irq_info		= flexanet_pcmcia_get_irq_info,
+  .configure_socket	= flexanet_pcmcia_configure_socket,
+
+  .socket_init		= flexanet_pcmcia_socket_init,
+  .socket_suspend	= flexanet_pcmcia_socket_suspend,
 };
 
 int __init pcmcia_flexanet_init(void)

drivers/pcmcia/sa1100_freebird.c

@@ -9,6 +9,7 @@
 #include <linux/init.h>
 
 #include <asm/hardware.h>
+#include <asm/mach-types.h>
 #include <asm/irq.h>
 #include "sa1100_generic.h"
 
@@ -178,14 +179,14 @@ static int freebird_pcmcia_socket_suspend(int sock)
 }
 
 static struct pcmcia_low_level freebird_pcmcia_ops = {
-  init:			freebird_pcmcia_init,
-  shutdown:		freebird_pcmcia_shutdown,
-  socket_state:		freebird_pcmcia_socket_state,
-  get_irq_info:		freebird_pcmcia_get_irq_info,
-  configure_socket:	freebird_pcmcia_configure_socket,
-
-  socket_init:		freebird_pcmcia_socket_init,
-  socket_suspend:	freebird_pcmcia_socket_suspend,
+  .init			= freebird_pcmcia_init,
+  .shutdown		= freebird_pcmcia_shutdown,
+  .socket_state		= freebird_pcmcia_socket_state,
+  .get_irq_info		= freebird_pcmcia_get_irq_info,
+  .configure_socket	= freebird_pcmcia_configure_socket,
+
+  .socket_init		= freebird_pcmcia_socket_init,
+  .socket_suspend	= freebird_pcmcia_socket_suspend,
 };
 
 int __init pcmcia_freebird_init(void)

drivers/pcmcia/sa1100_generic.c

@@ -719,7 +719,7 @@ sa1100_pcmcia_set_mem_map(unsigned int sock, struct pccard_mem_map *map)
 	(map->flags&MAP_ATTRIB)?"ATTRIB ":"",
 	(map->flags&MAP_USE_WAIT)?"USE_WAIT ":"");
 
-  if (map->map >= MAX_WIN){
+  if (map->map >= MAX_WIN) {
     printk(KERN_ERR "%s(): map (%d) out of range\n", __FUNCTION__,
 	   map->map);
     return -1;
@@ -853,19 +853,19 @@ sa1100_pcmcia_proc_setup(unsigned int sock, struct proc_dir_entry *base)
 #endif  /* defined(CONFIG_PROC_FS) */
 
 static struct pccard_operations sa1100_pcmcia_operations = {
-  init:			sa1100_pcmcia_sock_init,
-  suspend:		sa1100_pcmcia_suspend,
-  register_callback:	sa1100_pcmcia_register_callback,
-  inquire_socket:	sa1100_pcmcia_inquire_socket,
-  get_status:		sa1100_pcmcia_get_status,
-  get_socket:		sa1100_pcmcia_get_socket,
-  set_socket:		sa1100_pcmcia_set_socket,
-  get_io_map:		sa1100_pcmcia_get_io_map,
-  set_io_map:		sa1100_pcmcia_set_io_map,
-  get_mem_map:		sa1100_pcmcia_get_mem_map,
-  set_mem_map:		sa1100_pcmcia_set_mem_map,
+  .init			= sa1100_pcmcia_sock_init,
+  .suspend		= sa1100_pcmcia_suspend,
+  .register_callback	= sa1100_pcmcia_register_callback,
+  .inquire_socket	= sa1100_pcmcia_inquire_socket,
+  .get_status		= sa1100_pcmcia_get_status,
+  .get_socket		= sa1100_pcmcia_get_socket,
+  .set_socket		= sa1100_pcmcia_set_socket,
+  .get_io_map		= sa1100_pcmcia_get_io_map,
+  .set_io_map		= sa1100_pcmcia_set_io_map,
+  .get_mem_map		= sa1100_pcmcia_get_mem_map,
+  .set_mem_map		= sa1100_pcmcia_set_mem_map,
 #ifdef CONFIG_PROC_FS
-  proc_setup:		sa1100_pcmcia_proc_setup
+  .proc_setup		= sa1100_pcmcia_proc_setup
 #endif
 };
 
@@ -927,7 +927,7 @@ sa1100_pcmcia_notifier(struct notifier_block *nb, unsigned long val,
 }
 
 static struct notifier_block sa1100_pcmcia_notifier_block = {
-	notifier_call:	sa1100_pcmcia_notifier
+	.notifier_call	= sa1100_pcmcia_notifier
 };
 #endif
 
@@ -1148,6 +1148,9 @@ static int __init sa1100_pcmcia_init(void)
 #ifdef CONFIG_SA1100_GRAPHICSCLIENT
 	pcmcia_gcplus_init();
 #endif
+#ifdef CONFIG_SA1100_H3600
+	pcmcia_h3600_init();
+#endif
 #ifdef CONFIG_SA1100_PANGOLIN
 	pcmcia_pangolin_init();
 #endif
@@ -1192,6 +1195,9 @@ static void __exit sa1100_pcmcia_exit(void)
 #ifdef CONFIG_SA1100_GRAPHICSCLIENT
 	pcmcia_gcplus_exit();
 #endif
+#ifdef CONFIG_SA1100_H3600
+	pcmcia_h3600_exit();
+#endif
 #ifdef CONFIG_SA1100_PANGOLIN
 	pcmcia_pangolin_exit();
 #endif

drivers/pcmcia/sa1100_graphicsclient.c

@@ -17,6 +17,7 @@
 #include <linux/init.h>
 
 #include <asm/hardware.h>
+#include <asm/mach-types.h>
 #include <asm/irq.h>
 #include "sa1100_generic.h"
 
@@ -159,14 +160,14 @@ static int gcplus_pcmcia_socket_suspend(int sock)
 }
 
 static struct pcmcia_low_level gcplus_pcmcia_ops = { 
-  init:			gcplus_pcmcia_init,
-  shutdown:		gcplus_pcmcia_shutdown,
-  socket_state:		gcplus_pcmcia_socket_state,
-  get_irq_info:		gcplus_pcmcia_get_irq_info,
-  configure_socket:	gcplus_pcmcia_configure_socket,
-
-  socket_init:		gcplus_pcmcia_socket_init,
-  socket_suspend:	gcplus_pcmcia_socket_suspend,
+  .init			= gcplus_pcmcia_init,
+  .shutdown		= gcplus_pcmcia_shutdown,
+  .socket_state		= gcplus_pcmcia_socket_state,
+  .get_irq_info		= gcplus_pcmcia_get_irq_info,
+  .configure_socket	= gcplus_pcmcia_configure_socket,
+
+  .socket_init		= gcplus_pcmcia_socket_init,
+  .socket_suspend	= gcplus_pcmcia_socket_suspend,
 };
 
 int __init pcmcia_gcplus_init(void)

drivers/pcmcia/sa1100_graphicsmaster.c

@@ -82,14 +82,14 @@ graphicsmaster_pcmcia_configure_socket(const struct pcmcia_configure *conf)
 }
 
 static struct pcmcia_low_level graphicsmaster_pcmcia_ops = {
-  init:			graphicsmaster_pcmcia_init,
-  shutdown:		sa1111_pcmcia_shutdown,
-  socket_state:		sa1111_pcmcia_socket_state,
-  get_irq_info:		sa1111_pcmcia_get_irq_info,
-  configure_socket:	graphicsmaster_pcmcia_configure_socket,
-
-  socket_init:		sa1111_pcmcia_socket_init,
-  socket_suspend:	sa1111_pcmcia_socket_suspend,
+  .init			= graphicsmaster_pcmcia_init,
+  .shutdown		= sa1111_pcmcia_shutdown,
+  .socket_state		= sa1111_pcmcia_socket_state,
+  .get_irq_info		= sa1111_pcmcia_get_irq_info,
+  .configure_socket	= graphicsmaster_pcmcia_configure_socket,
+
+  .socket_init		= sa1111_pcmcia_socket_init,
+  .socket_suspend	= sa1111_pcmcia_socket_suspend,
 };
 
 int __init pcmcia_graphicsmaster_init(void)

drivers/pcmcia/sa1100_h3600.c

@@ -10,6 +10,9 @@
 
 #include <asm/hardware.h>
 #include <asm/irq.h>
+#include <asm/mach-types.h>
+#include <asm/arch/h3600.h>
+
 #include "sa1100_generic.h"
 
 static struct irqs {
@@ -185,13 +188,27 @@ static int h3600_pcmcia_socket_suspend(int sock)
 }
 
 struct pcmcia_low_level h3600_pcmcia_ops = { 
-	init:			h3600_pcmcia_init,
-	shutdown:		h3600_pcmcia_shutdown,
-	socket_state:		h3600_pcmcia_socket_state,
-	get_irq_info:		h3600_pcmcia_get_irq_info,
-	configure_socket:	h3600_pcmcia_configure_socket,
-
-	socket_init:		h3600_pcmcia_socket_init,
-	socket_suspend:		h3600_pcmcia_socket_suspend,
+	.init			= h3600_pcmcia_init,
+	.shutdown		= h3600_pcmcia_shutdown,
+	.socket_state		= h3600_pcmcia_socket_state,
+	.get_irq_info		= h3600_pcmcia_get_irq_info,
+	.configure_socket	= h3600_pcmcia_configure_socket,
+
+	.socket_init		= h3600_pcmcia_socket_init,
+	.socket_suspend		= h3600_pcmcia_socket_suspend,
 };
 
+int __init pcmcia_h3600_init(void)
+{
+	int ret = -ENODEV;
+
+	if (machine_is_h3600())
+		ret = sa1100_register_pcmcia(&h3600_pcmcia_ops);
+
+	return ret;
+}
+
+void __exit pcmcia_h3600_exit(void)
+{
+	sa1100_unregister_pcmcia(&h3600_pcmcia_ops);
+}

drivers/pcmcia/sa1100_jornada720.c

@@ -97,14 +97,14 @@ printk("%s(): config socket %d vcc %d vpp %d\n", __FUNCTION__,
 }
 
 static struct pcmcia_low_level jornada720_pcmcia_ops = {
-  init:			jornada720_pcmcia_init,
-  shutdown:		sa1111_pcmcia_shutdown,
-  socket_state:		sa1111_pcmcia_socket_state,
-  get_irq_info:		sa1111_pcmcia_get_irq_info,
-  configure_socket:	jornada720_pcmcia_configure_socket,
-
-  socket_init:		sa1111_pcmcia_socket_init,
-  socket_suspend:	sa1111_pcmcia_socket_suspend,
+  .init			= jornada720_pcmcia_init,
+  .shutdown		= sa1111_pcmcia_shutdown,
+  .socket_state		= sa1111_pcmcia_socket_state,
+  .get_irq_info		= sa1111_pcmcia_get_irq_info,
+  .configure_socket	= jornada720_pcmcia_configure_socket,
+
+  .socket_init		= sa1111_pcmcia_socket_init,
+  .socket_suspend	= sa1111_pcmcia_socket_suspend,
 };
 
 int __init pcmcia_jornada720_init(void)

drivers/pcmcia/sa1100_neponset.c

@@ -127,14 +127,14 @@ neponset_pcmcia_configure_socket(const struct pcmcia_configure *conf)
 }
 
 static struct pcmcia_low_level neponset_pcmcia_ops = {
-	init:			neponset_pcmcia_init,
-	shutdown:		sa1111_pcmcia_shutdown,
-	socket_state:		sa1111_pcmcia_socket_state,
-	get_irq_info:		sa1111_pcmcia_get_irq_info,
-	configure_socket:	neponset_pcmcia_configure_socket,
-
-	socket_init:		sa1111_pcmcia_socket_init,
-	socket_suspend:		sa1111_pcmcia_socket_suspend,
+	.init			= neponset_pcmcia_init,
+	.shutdown		= sa1111_pcmcia_shutdown,
+	.socket_state		= sa1111_pcmcia_socket_state,
+	.get_irq_info		= sa1111_pcmcia_get_irq_info,
+	.configure_socket	= neponset_pcmcia_configure_socket,
+
+	.socket_init		= sa1111_pcmcia_socket_init,
+	.socket_suspend		= sa1111_pcmcia_socket_suspend,
 };
 
 int __init pcmcia_neponset_init(void)

drivers/pcmcia/sa1100_pangolin.c

@@ -10,6 +10,7 @@
 #include <linux/init.h>
 
 #include <asm/hardware.h>
+#include <asm/mach-types.h>
 #include <asm/irq.h>
 #include "sa1100_generic.h"
 
@@ -159,13 +160,13 @@ static int pangolin_pcmcia_socket_suspend(int sock)
 }
 
 static struct pcmcia_low_level pangolin_pcmcia_ops = { 
-  init:			pangolin_pcmcia_init,
-  shutdown:		pangolin_pcmcia_shutdown,
-  socket_state:		pangolin_pcmcia_socket_state,
-  get_irq_info:		pangolin_pcmcia_get_irq_info,
-  configure_socket:	pangolin_pcmcia_configure_socket,
+  .init			= pangolin_pcmcia_init,
+  .shutdown		= pangolin_pcmcia_shutdown,
+  .socket_state		= pangolin_pcmcia_socket_state,
+  .get_irq_info		= pangolin_pcmcia_get_irq_info,
+  .configure_socket	= pangolin_pcmcia_configure_socket,
 
-  socket_init:		pangolin_pcmcia_socket_init,
+  .socket_init		= pangolin_pcmcia_socket_init,
   socket_suspend,	pangolin_pcmcia_socket_suspend,
 };
 

drivers/pcmcia/sa1100_pfs168.c

@@ -119,14 +119,14 @@ pfs168_pcmcia_configure_socket(const struct pcmcia_configure *conf)
 }
 
 static struct pcmcia_low_level pfs168_pcmcia_ops = {
-  init:			pfs168_pcmcia_init,
-  shutdown:		sa1111_pcmcia_shutdown,
-  socket_state:		sa1111_pcmcia_socket_state,
-  get_irq_info:		sa1111_pcmcia_get_irq_info,
-  configure_socket:	pfs168_pcmcia_configure_socket,
-
-  socket_init:		sa1111_pcmcia_socket_init,
-  socket_suspend:	sa1111_pcmcia_socket_suspend,
+  .init			= pfs168_pcmcia_init,
+  .shutdown		= sa1111_pcmcia_shutdown,
+  .socket_state		= sa1111_pcmcia_socket_state,
+  .get_irq_info		= sa1111_pcmcia_get_irq_info,
+  .configure_socket	= pfs168_pcmcia_configure_socket,
+
+  .socket_init		= sa1111_pcmcia_socket_init,
+  .socket_suspend	= sa1111_pcmcia_socket_suspend,
 };
 
 int __init pcmcia_pfs168_init(void)

drivers/pcmcia/sa1100_shannon.c

@@ -9,6 +9,7 @@
 #include <linux/init.h>
 
 #include <asm/hardware.h>
+#include <asm/mach-types.h>
 #include <asm/arch/shannon.h>
 #include <asm/irq.h>
 #include "sa1100_generic.h"
@@ -151,14 +152,14 @@ static int shannon_pcmcia_socket_suspend(int sock)
 }
 
 static struct pcmcia_low_level shannon_pcmcia_ops = {
-	init:			shannon_pcmcia_init,
-	shutdown:		shannon_pcmcia_shutdown,
-	socket_state:		shannon_pcmcia_socket_state,
-	get_irq_info:		shannon_pcmcia_get_irq_info,
-	configure_socket:	shannon_pcmcia_configure_socket,
-
-	socket_init:		shannon_pcmcia_socket_init,
-	socket_suspend:		shannon_pcmcia_socket_suspend,
+	.init			= shannon_pcmcia_init,
+	.shutdown		= shannon_pcmcia_shutdown,
+	.socket_state		= shannon_pcmcia_socket_state,
+	.get_irq_info		= shannon_pcmcia_get_irq_info,
+	.configure_socket	= shannon_pcmcia_configure_socket,
+
+	.socket_init		= shannon_pcmcia_socket_init,
+	.socket_suspend		= shannon_pcmcia_socket_suspend,
 };
 
 int __init pcmcia_shannon_init(void)

drivers/serial/Makefile

@@ -13,6 +13,7 @@ obj-$(CONFIG_SERIAL_CORE) += core.o
 obj-$(CONFIG_SERIAL_21285) += 21285.o
 obj-$(CONFIG_SERIAL_8250) += 8250.o $(serial-8250-y)
 obj-$(CONFIG_SERIAL_8250_CS) += 8250_cs.o
+obj-$(CONFIG_SERIAL_8250_ACORN) += 8250_acorn.o
 obj-$(CONFIG_SERIAL_ANAKIN) += anakin.o
 obj-$(CONFIG_SERIAL_AMBA) += amba.o
 obj-$(CONFIG_SERIAL_CLPS711X) += clps711x.o