Skip to content

L
linux
Commit e1f5aa3d authored by Justin T. Gibbs's avatar Justin T. Gibbs
Browse files
Options

Update aic79xx Driver to 1.3.4 

 o Fix stray PCI target abort interrupt on startup due to accessing a
   register prior to pausing the controller.
 o Add cfg4icmd implementation.
 o Fix PCI-X issues on rev A hardware due to improper accesses to
   scb ram.
 o Correct a race condition in the error recovery path.
parent 6d1101b3
Expand all Show whitespace changes
Inline Side-by-side
Showing with 266 additions and 188 deletions
drivers/scsi/aic7xxx/aic79xx.h
View file @ e1f5aa3d
......@@ -37,7 +37,7 @@
* IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGES.
*
* $Id: //depot/aic7xxx/aic7xxx/aic79xx.h#81 $
* $Id: //depot/aic7xxx/aic7xxx/aic79xx.h#85 $
*
* $FreeBSD$
*/
......@@ -258,27 +258,30 @@ typedef enum {
AHD_PCIX_CHIPRST_BUG = 0x0040,
/* MMAPIO is not functional in PCI-X mode. */
AHD_PCIX_MMAPIO_BUG = 0x0080,
/* Reads to SCBRAM fail to reset the discard timer. */
AHD_PCIX_SCBRAM_RD_BUG = 0x0100,
/* Bug workarounds that can be disabled on non-PCIX busses. */
AHD_PCIX_BUG_MASK = AHD_PCIX_CHIPRST_BUG
| AHD_PCIX_MMAPIO_BUG,
| AHD_PCIX_MMAPIO_BUG
| AHD_PCIX_SCBRAM_RD_BUG,
/*
* LQOSTOP0 status set even for forced selections with ATN
* to perform non-packetized message delivery.
*/
AHD_LQO_ATNO_BUG = 0x0100,
AHD_LQO_ATNO_BUG = 0x0200,
/* FIFO auto-flush does not always trigger. */
AHD_AUTOFLUSH_BUG = 0x0200,
AHD_AUTOFLUSH_BUG = 0x0400,
/* The CLRLQO registers are not self-clearing. */
AHD_CLRLQO_AUTOCLR_BUG = 0x0400,
AHD_CLRLQO_AUTOCLR_BUG = 0x0800,
/* The PACKETIZED status bit refers to the previous connection. */
AHD_PKTIZED_STATUS_BUG = 0x0800,
AHD_PKTIZED_STATUS_BUG = 0x1000,
/* "Short Luns" are not placed into outgoing LQ packets correctly. */
AHD_PKT_LUN_BUG = 0x1000,
AHD_PKT_LUN_BUG = 0x2000,
/*
* Only the FIFO allocated to the non-packetized connection may
* be in use during a non-packetzied connection.
*/
AHD_NONPACKFIFO_BUG = 0x2000,
AHD_NONPACKFIFO_BUG = 0x4000,
/*
* Writing to a DFF SCBPTR register may fail if concurent with
* a hardware write to the other DFF SCBPTR register. This is
......@@ -286,40 +289,40 @@ typedef enum {
* this bug have the AHD_NONPACKFIFO_BUG and all writes of concern
* occur in non-packetized connections.
*/
AHD_MDFF_WSCBPTR_BUG = 0x4000,
AHD_MDFF_WSCBPTR_BUG = 0x8000,
/* SGHADDR updates are slow. */
AHD_REG_SLOW_SETTLE_BUG = 0x8000,
AHD_REG_SLOW_SETTLE_BUG = 0x10000,
/*
* Changing the MODE_PTR coincident with an interrupt that
* switches to a different mode will cause the interrupt to
* be in the mode written outside of interrupt context.
*/
AHD_SET_MODE_BUG = 0x10000,
AHD_SET_MODE_BUG = 0x20000,
/* Non-packetized busfree revision does not work. */
AHD_BUSFREEREV_BUG = 0x20000,
AHD_BUSFREEREV_BUG = 0x40000,
/*
* Paced transfers are indicated with a non-standard PPR
* option bit in the neg table, 160MHz is indicated by
* sync factor 0x7, and the offset if off by a factor of 2.
*/
AHD_PACED_NEGTABLE_BUG = 0x40000,
AHD_PACED_NEGTABLE_BUG = 0x80000,
/* LQOOVERRUN false positives. */
AHD_LQOOVERRUN_BUG = 0x80000,
AHD_LQOOVERRUN_BUG = 0x100000,
/*
* Controller write to INTSTAT will lose to a host
* write to CLRINT.
*/
AHD_INTCOLLISION_BUG = 0x100000,
AHD_INTCOLLISION_BUG = 0x200000,
/*
* The GEM318 violates the SCSI spec by not waiting
* the mandated bus settle delay between phase changes
* in some situations. Some aic79xx chip revs. are more
* strict in this regard and will treat REQ assertions
* that fall within the bus settle delay window as
* glitches. This flag enables causes the firmware
* to tolerate early REQ assertions.
* glitches. This flag tells the firmware to tolerate
* early REQ assertions.
*/
AHD_EARLY_REQ_BUG = 0x200000
AHD_EARLY_REQ_BUG = 0x400000
} ahd_bug;
/*
......@@ -421,7 +424,10 @@ typedef uint32_t sense_addr_t;
#define MAX_CDB_LEN 16
#define MAX_CDB_LEN_WITH_SENSE_ADDR (MAX_CDB_LEN - sizeof(sense_addr_t))
union initiator_data {
struct {
uint64_t cdbptr;
uint8_t cdblen;
} cdb_from_host;
uint8_t cdb[MAX_CDB_LEN];
struct {
uint8_t cdb[MAX_CDB_LEN_WITH_SENSE_ADDR];
......
drivers/scsi/aic7xxx/aic79xx.reg
View file @ e1f5aa3d
......@@ -39,7 +39,7 @@
*
* $FreeBSD$
*/
VERSION = "$Id: //depot/aic7xxx/aic7xxx/aic79xx.reg#61 $"
VERSION = "$Id: //depot/aic7xxx/aic7xxx/aic79xx.reg#64 $"
/*
* This file is processed by the aic7xxx_asm utility for use in assembling
......@@ -2071,14 +2071,14 @@ register LQIMODE1 {
address 0x051
access_mode RW
modes M_CFG
field ENLQIPHASE_LQ 0x80
field ENLQIPHASE_NLQ 0x40
field ENLQIPHASE_LQ 0x80 /* LQIPHASE1 */
field ENLQIPHASE_NLQ 0x40 /* LQIPHASE2 */
field ENLIQABORT 0x20
field ENLQICRCI_LQ 0x10
field ENLQICRCI_NLQ 0x08
field ENLQICRCI_LQ 0x10 /* LQICRCI1 */
field ENLQICRCI_NLQ 0x08 /* LQICRCI2 */
field ENLQIBADLQI 0x04
field ENLQIOVERI_LQ 0x02
field ENLQIOVERI_NLQ 0x01
field ENLQIOVERI_LQ 0x02 /* LQIOVERI1 */
field ENLQIOVERI_NLQ 0x01 /* LQIOVERI2 */
}
/*
......@@ -3769,16 +3769,17 @@ scb {
SCB_RESIDUAL_DATACNT {
size 4
alias SCB_CDB_STORE
alias SCB_HOST_CDB_PTR
}
SCB_RESIDUAL_SGPTR {
size 4
alias SCB_CDB_PTR
field SG_ADDR_MASK 0xf8 /* In the last byte */
field SG_OVERRUN_RESID 0x02 /* In the first byte */
field SG_LIST_NULL 0x01 /* In the first byte */
}
SCB_SCSI_STATUS {
size 1
alias SCB_HOST_CDB_LEN
}
SCB_TARGET_PHASES {
size 1
......
drivers/scsi/aic7xxx/aic79xx.seq
View file @ e1f5aa3d
......@@ -40,7 +40,7 @@
* $FreeBSD$
*/
VERSION = "$Id: //depot/aic7xxx/aic7xxx/aic79xx.seq#86 $"
VERSION = "$Id: //depot/aic7xxx/aic7xxx/aic79xx.seq#88 $"
PATCH_ARG_LIST = "struct ahd_softc *ahd"
PREFIX = "ahd_"
......@@ -708,7 +708,7 @@ SET_DST_MODE M_DFF1;
add NONE, -17, SCB_CDB_LEN;
jnc p_command_embedded;
p_command_from_host:
bmov HADDR[0], SCB_CDB_PTR, 11;
bmov HADDR[0], SCB_HOST_CDB_PTR, 9;
mvi SG_CACHE_PRE, LAST_SEG;
mvi DFCNTRL, (PRELOADEN|SCSIEN|HDMAEN);
jmp p_command_xfer;
......@@ -1693,6 +1693,18 @@ cfg4istat_no_taskmgmt_func:
call pkt_handle_status;
or SEQINTCTL, IRET ret;
cfg4icmd_intr:
/*
* In the case of DMAing a CDB from the host, the normal
* CDB buffer is formatted with an 8 byte address followed
* by a 1 byte count.
*/
bmov HADDR[0], SCB_HOST_CDB_PTR, 9;
mvi SG_CACHE_PRE, LAST_SEG;
mvi DFCNTRL, (PRELOADEN|SCSIEN|HDMAEN);
call pkt_handle_cdb;
or SEQINTCTL, IRET ret;
/*
* See if the target has gone on in this context creating an
* overrun condition. For the write case, the hardware cannot
......@@ -1825,13 +1837,15 @@ BEGIN_CRITICAL;
mvi DFFSXFRCTL, CLRCHN ret;
END_CRITICAL;
check_status_overrun:
test SHCNT[2], 0xFF jz status_IU_done;
SET_SEQINTCODE(STATUS_OVERRUN)
jmp status_IU_done;
/*
* Watch over the status transfer. Our host sense buffer is
* large enough to take the maximum allowed status packet.
* None-the-less, we must still catch and report overruns to
* the host.
*/
pkt_handle_status:
call setjmp_setscb;
test MDFFSTAT, LASTSDONE jnz check_status_overrun;
test SG_CACHE_SHADOW, LAST_SEG_DONE jz check_status_overrun;
test SEQINTSRC, CTXTDONE jz return;
status_IU_done:
BEGIN_CRITICAL;
......@@ -1843,6 +1857,21 @@ BEGIN_CRITICAL;
or SCB_CONTROL, STATUS_RCVD;
jmp last_pkt_complete;
END_CRITICAL;
check_status_overrun:
/*
* We've filled the entire sense buffer.
* Wait for either context done or a negative
* shaddow count. If the context completes without
* causing the shaddow count to go negative, then
* this was a successful transfer up to the status
* limit. Otherwise we report the error.
*/
test SHCNT[2], 0xFF jnz report_status_overrun;
test SEQINTSRC, CTXTDONE jz return;
test SHCNT[2], 0xFF jz status_IU_done;
report_status_overrun:
SET_SEQINTCODE(STATUS_OVERRUN)
jmp status_IU_done;
SET_SRC_MODE M_DFF0;
SET_DST_MODE M_DFF0;
......@@ -1856,6 +1885,16 @@ check_fifo:
stc ret;
END_CRITICAL;
/*
* Must wait until CDB xfer is over before issuing the
* clear channel.
*/
pkt_handle_cdb:
call setjmp_setscb;
test SG_CACHE_SHADOW, LAST_SEG_DONE jz return;
or LONGJMP_ADDR[1], INVALID_ADDR;
mvi DFFSXFRCTL, CLRCHN ret;
/*
* Nonpackreq is a polled status. It can come true in three situations:
* we have received an L_Q, we have sent one or more L_Qs, or there is no
......@@ -1925,6 +1964,7 @@ pkt_overrun_end:
or SCB_RESIDUAL_SGPTR, SG_OVERRUN_RESID;
test SEQINTSRC, CTXTDONE jz unexpected_nonpkt_phase;
test SCB_CONTROL, STATUS_RCVD jnz last_pkt_queue_scb;
or LONGJMP_ADDR[1], INVALID_ADDR;
mvi DFFSXFRCTL, CLRCHN ret;
if ((ahd->bugs & AHD_PKT_BITBUCKET_BUG) != 0) {
......@@ -1945,5 +1985,3 @@ load_overrun_buf:
mvi HCNT[1], ((PKT_OVERRUN_BUFSIZE >> 8) & 0xFF);
clr HCNT[2] ret;
}
cfg4icmd_intr:
drivers/scsi/aic7xxx/aic79xx_core.c
View file @ e1f5aa3d
......@@ -37,7 +37,7 @@
* IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGES.
*
* $Id: //depot/aic7xxx/aic7xxx/aic79xx.c#163 $
* $Id: //depot/aic7xxx/aic7xxx/aic79xx.c#172 $
*
* $FreeBSD$
*/
......@@ -406,7 +406,7 @@ ahd_flush_qoutfifo(struct ahd_softc *ahd)
u_int i;
ahd_set_scbptr(ahd, scbid);
next_scbid = ahd_inw(ahd, SCB_NEXT_COMPLETE);
next_scbid = ahd_inw_scbram(ahd, SCB_NEXT_COMPLETE);
scb = ahd_lookup_scb(ahd, scbid);
if (scb == NULL) {
printf("%s: Warning - DMA-up and complete "
......@@ -415,7 +415,7 @@ ahd_flush_qoutfifo(struct ahd_softc *ahd)
}
hscb_ptr = (uint8_t *)scb->hscb;
for (i = 0; i < sizeof(struct hardware_scb); i++)
*hscb_ptr++ = ahd_inb(ahd, SCB_BASE + i);
*hscb_ptr++ = ahd_inb_scbram(ahd, SCB_BASE + i);
ahd_complete_scb(ahd, scb);
scbid = next_scbid;
......@@ -426,7 +426,7 @@ ahd_flush_qoutfifo(struct ahd_softc *ahd)
while (!SCBID_IS_NULL(scbid)) {
ahd_set_scbptr(ahd, scbid);
next_scbid = ahd_inw(ahd, SCB_NEXT_COMPLETE);
next_scbid = ahd_inw_scbram(ahd, SCB_NEXT_COMPLETE);
scb = ahd_lookup_scb(ahd, scbid);
if (scb == NULL) {
printf("%s: Warning - Complete SCB %d invalid\n",
......@@ -1292,9 +1292,9 @@ ahd_handle_scsiint(struct ahd_softc *ahd, u_int intstat)
scbid = ahd_get_scbptr(ahd);
scb = ahd_lookup_scb(ahd, scbid);
if (scb == NULL) {
printf("%s: Invalid SCB in DFF%d "
printf("%s: Invalid SCB %d in DFF%d "
"during unexpected busfree\n",
ahd_name(ahd), mode);
ahd_name(ahd), scbid, mode);
packetized = 0;
} else
packetized = (scb->flags & SCB_PACKETIZED) != 0;
......@@ -1667,7 +1667,7 @@ ahd_handle_pkt_busfree(struct ahd_softc *ahd, u_int busfreetime)
next = SCB_LIST_NULL;
} else {
ahd_set_scbptr(ahd, waiting_h);
next = ahd_inw(ahd, SCB_NEXT2);
next = ahd_inw_scbram(ahd, SCB_NEXT2);
}
ahd_set_scbptr(ahd, scbid);
ahd_outw(ahd, SCB_NEXT2, next);
......@@ -1998,7 +1998,8 @@ ahd_handle_proto_violation(struct ahd_softc *ahd)
if ((seq_flags & NO_CDB_SENT) != 0) {
ahd_print_path(ahd, scb);
printf("No or incomplete CDB sent to device.\n");
} else if ((ahd_inb(ahd, SCB_CONTROL) & STATUS_RCVD) == 0) {
} else if ((ahd_inb_scbram(ahd, SCB_CONTROL)
& STATUS_RCVD) == 0) {
/*
* The target never bothered to provide status to
* us prior to completing the command. Since we don't
......@@ -2615,8 +2616,12 @@ ahd_set_syncrate(struct ahd_softc *ahd, struct ahd_devinfo *devinfo,
ahd_name(ahd), devinfo->target,
period, offset);
options = 0;
if ((ppr_options & MSG_EXT_PPR_RD_STRM) != 0) {
printf("(RDSTRM");
options++;
}
if ((ppr_options & MSG_EXT_PPR_DT_REQ) != 0) {
printf("(DT");
printf("%s", options ? "|DT" : "(DT");
options++;
}
if ((ppr_options & MSG_EXT_PPR_IU_REQ) != 0) {
......@@ -4990,6 +4995,8 @@ ahd_reset(struct ahd_softc *ahd)
* to disturb the integrity of the bus.
*/
ahd_pause(ahd);
ahd_update_modes(ahd);
ahd_set_modes(ahd, AHD_MODE_SCSI, AHD_MODE_SCSI);
sxfrctl1 = ahd_inb(ahd, SXFRCTL1);
cmd = ahd_pci_read_config(ahd->dev_softc, PCIR_COMMAND, /*bytes*/2);
......@@ -5038,13 +5045,16 @@ ahd_reset(struct ahd_softc *ahd)
ahd_pci_write_config(ahd->dev_softc, PCIR_COMMAND,
cmd, /*bytes*/2);
}
/* After a reset, we know the state of the mode register. */
ahd_known_modes(ahd, AHD_MODE_SCSI, AHD_MODE_SCSI);
/* Determine chip configuration */
ahd->features &= ~AHD_WIDE;
if ((ahd_inb(ahd, SBLKCTL) & SELWIDE) != 0)
ahd->features |= AHD_WIDE;
/*
* Mode should be SCSI after a chip reset, but lets
* set it just to be safe. We touch the MODE_PTR
* register directly so as to bypass the lazy update
* code in ahd_set_modes().
*/
ahd_known_modes(ahd, AHD_MODE_SCSI, AHD_MODE_SCSI);
ahd_outb(ahd, MODE_PTR,
ahd_build_mode_state(ahd, AHD_MODE_SCSI, AHD_MODE_SCSI));
/*
* Restore SXFRCTL1.
......@@ -5057,6 +5067,11 @@ ahd_reset(struct ahd_softc *ahd)
ahd_outb(ahd, SXFRCTL1, sxfrctl1|STPWEN);
ahd_outb(ahd, SXFRCTL1, sxfrctl1);
/* Determine chip configuration */
ahd->features &= ~AHD_WIDE;
if ((ahd_inb(ahd, SBLKCTL) & SELWIDE) != 0)
ahd->features |= AHD_WIDE;
/*
* If a recovery action has forced a chip reset,
* re-initialize the chip to our liking.
......@@ -5803,7 +5818,9 @@ ahd_init(struct ahd_softc *ahd)
/* DMA tag for mapping buffers into device visible space. */
if (ahd_dma_tag_create(ahd, ahd->parent_dmat, /*alignment*/1,
/*boundary*/BUS_SPACE_MAXADDR_32BIT + 1,
/*lowaddr*/BUS_SPACE_MAXADDR,
/*lowaddr*/ahd->flags & AHD_39BIT_ADDRESSING
? (bus_addr_t)0x7FFFFFFFFFULL
: BUS_SPACE_MAXADDR_32BIT,
/*highaddr*/BUS_SPACE_MAXADDR,
/*filter*/NULL, /*filterarg*/NULL,
/*maxsize*/(AHD_NSEG - 1) * PAGE_SIZE,
......@@ -7683,7 +7700,6 @@ ahd_handle_scsi_status(struct ahd_softc *ahd, struct scb *scb)
{
struct hardware_scb *hscb;
u_int qfreeze_cnt;
ahd_mode_state saved_modes;
/*
* The sequencer freezes its select-out queue
......@@ -7695,7 +7711,6 @@ ahd_handle_scsi_status(struct ahd_softc *ahd, struct scb *scb)
/* Freeze the queue until the client sees the error. */
ahd_pause(ahd);
saved_modes = ahd_save_modes(ahd);
ahd_clear_critical_section(ahd);
ahd_set_modes(ahd, AHD_MODE_SCSI, AHD_MODE_SCSI);
ahd_freeze_devq(ahd, scb);
......
drivers/scsi/aic7xxx/aic79xx_inline.h
View file @ e1f5aa3d
......@@ -37,7 +37,7 @@
* IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGES.
*
* $Id: //depot/aic7xxx/aic7xxx/aic79xx_inline.h#42 $
* $Id: //depot/aic7xxx/aic7xxx/aic79xx_inline.h#44 $
*
* $FreeBSD$
*/
......@@ -678,6 +678,7 @@ ahd_inb_scbram(struct ahd_softc *ahd, u_int offset)
* Razor #528
*/
value = ahd_inb(ahd, offset);
if ((ahd->flags & AHD_PCIX_SCBRAM_RD_BUG) != 0)
ahd_inb(ahd, MODE_PTR);
return (value);
}
......
drivers/scsi/aic7xxx/aic79xx_osm.c
View file @ e1f5aa3d
/*
* Adaptec AIC79xx device driver for Linux.
*
* $Id: //depot/aic7xxx/linux/drivers/scsi/aic7xxx/aic79xx_osm.c#124 $
* $Id: //depot/aic7xxx/linux/drivers/scsi/aic7xxx/aic79xx_osm.c#128 $
*
* --------------------------------------------------------------------------
* Copyright (c) 1994-2000 Justin T. Gibbs.
......@@ -1462,14 +1462,14 @@ ahd_linux_abort(Scsi_Cmnd *cmd)
struct timer_list timer;
int ret;
ahd->platform_data->flags |= AHD_UP_EH_SEMAPHORE;
pending_scb->platform_data->flags |= AHD_SCB_UP_EH_SEM;
#if LINUX_VERSION_CODE < KERNEL_VERSION(2,5,0)
ahd_unlock(ahd, &s);
#else
spin_unlock_irq(ahd->platform_data->host->host_lock);
#endif
init_timer(&timer);
timer.data = (u_long)ahd;
timer.data = (u_long)pending_scb;
timer.expires = jiffies + (5 * HZ);
timer.function = ahd_linux_sem_timeout;
add_timer(&timer);
......@@ -1583,14 +1583,14 @@ ahd_linux_dev_reset(Scsi_Cmnd *cmd)
LIST_INSERT_HEAD(&ahd->pending_scbs, scb, pending_links);
ahd_queue_scb(ahd, scb);
ahd->platform_data->flags |= AHD_UP_EH_SEMAPHORE;
scb->platform_data->flags |= AHD_SCB_UP_EH_SEM;
#if LINUX_VERSION_CODE < KERNEL_VERSION(2,5,0)
ahd_unlock(ahd, &s);
#else
spin_unlock_irq(ahd->platform_data->host->host_lock);
#endif
init_timer(&timer);
timer.data = (u_long)ahd;
timer.data = (u_long)scb;
timer.expires = jiffies + (5 * HZ);
timer.function = ahd_linux_sem_timeout;
add_timer(&timer);
......@@ -1697,7 +1697,7 @@ Scsi_Host_Template aic79xx_driver_template = {
.max_sectors = 8192,
#endif
#if defined CONFIG_HIGHIO || LINUX_VERSION_CODE >= KERNEL_VERSION(2,5,0)
#if LINUX_VERSION_CODE < KERNEL_VERSION(2,4,18)
#if LINUX_VERSION_CODE < KERNEL_VERSION(2,4,10)
/* Assume RedHat Distribution with its different HIGHIO conventions. */
.can_dma_32 = 1,
.single_sg_okay = 1,
......@@ -3050,6 +3050,7 @@ ahd_linux_dv_target(struct ahd_softc *ahd, u_int target_offset)
}
case AHD_DV_STATE_TUR:
case AHD_DV_STATE_BUSY:
timeout = 5 * HZ;
ahd_linux_dv_tur(ahd, cmd, &devinfo);
break;
case AHD_DV_STATE_REBD:
......@@ -4776,8 +4777,8 @@ ahd_done(struct ahd_softc *ahd, struct scb *scb)
if (ahd_get_transaction_status(scb) == CAM_BDR_SENT
|| ahd_get_transaction_status(scb) == CAM_REQ_ABORTED)
ahd_set_transaction_status(scb, CAM_CMD_TIMEOUT);
if ((ahd->platform_data->flags & AHD_UP_EH_SEMAPHORE) != 0) {
ahd->platform_data->flags &= ~AHD_UP_EH_SEMAPHORE;
if ((scb->platform_data->flags & AHD_SCB_UP_EH_SEM) != 0) {
scb->platform_data->flags &= ~AHD_SCB_UP_EH_SEM;
up(&ahd->platform_data->eh_sem);
}
}
......@@ -5279,13 +5280,15 @@ ahd_release_simq(struct ahd_softc *ahd)
static void
ahd_linux_sem_timeout(u_long arg)
{
struct scb *scb;
struct ahd_softc *ahd;
u_long s;
ahd = (struct ahd_softc *)arg;
scb = (struct scb *)arg;
ahd = scb->ahd_softc;
ahd_lock(ahd, &s);
if ((ahd->platform_data->flags & AHD_UP_EH_SEMAPHORE) != 0) {
ahd->platform_data->flags &= ~AHD_UP_EH_SEMAPHORE;
if ((scb->platform_data->flags & AHD_SCB_UP_EH_SEM) != 0) {
scb->platform_data->flags &= ~AHD_SCB_UP_EH_SEM;
up(&ahd->platform_data->eh_sem);
}
ahd_unlock(ahd, &s);
......
drivers/scsi/aic7xxx/aic79xx_osm.h
View file @ e1f5aa3d
......@@ -36,7 +36,7 @@
* IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGES.
*
* $Id: //depot/aic7xxx/linux/drivers/scsi/aic7xxx/aic79xx_osm.h#113 $
* $Id: //depot/aic7xxx/linux/drivers/scsi/aic7xxx/aic79xx_osm.h#117 $
*
*/
#ifndef _AIC79XX_LINUX_H_
......@@ -286,7 +286,7 @@ ahd_scb_timer_reset(struct scb *scb, u_int usec)
#include <linux/smp.h>
#endif
#define AIC79XX_DRIVER_VERSION "1.3.2"
#define AIC79XX_DRIVER_VERSION "1.3.4"
/**************************** Front End Queues ********************************/
/*
......@@ -487,7 +487,7 @@ struct ahd_linux_target {
* Per-SCB OSM storage.
*/
typedef enum {
AHD_UP_EH_SEMAPHORE = 0x1
AHD_SCB_UP_EH_SEM = 0x1
} ahd_linux_scb_flags;
struct scb_platform_data {
......
drivers/scsi/aic7xxx/aic79xx_pci.c
View file @ e1f5aa3d
......@@ -38,7 +38,7 @@
* IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGES.
*
* $Id: //depot/aic7xxx/aic7xxx/aic79xx_pci.c#66 $
* $Id: //depot/aic7xxx/aic7xxx/aic79xx_pci.c#67 $
*
* $FreeBSD$
*/
......@@ -385,12 +385,10 @@ ahd_pci_config(struct ahd_softc *ahd, struct ahd_pci_identity *entry)
int
ahd_pci_test_register_access(struct ahd_softc *ahd)
{
ahd_mode_state saved_modes;
uint32_t cmd;
int error;
uint8_t hcntrl;
saved_modes = ahd_save_modes(ahd);
error = EIO;
/*
......@@ -456,7 +454,6 @@ ahd_pci_test_register_access(struct ahd_softc *ahd)
ahd_outb(ahd, CLRINT, CLRPCIINT);
}
ahd_restore_modes(ahd, saved_modes);
ahd_outb(ahd, SEQCTL0, PERRORDIS|FAILDIS);
ahd_pci_write_config(ahd->dev_softc, PCIR_COMMAND, cmd, /*bytes*/2);
return (error);
......@@ -886,11 +883,11 @@ ahd_aic7902_setup(struct ahd_softc *ahd)
| AHD_NLQICRC_DELAYED_BUG|AHD_SCSIRST_BUG
| AHD_LQO_ATNO_BUG|AHD_AUTOFLUSH_BUG
| AHD_CLRLQO_AUTOCLR_BUG|AHD_PCIX_MMAPIO_BUG
| AHD_PCIX_CHIPRST_BUG|AHD_PKTIZED_STATUS_BUG
| AHD_PKT_LUN_BUG|AHD_MDFF_WSCBPTR_BUG
| AHD_REG_SLOW_SETTLE_BUG|AHD_SET_MODE_BUG
| AHD_BUSFREEREV_BUG|AHD_NONPACKFIFO_BUG
| AHD_PACED_NEGTABLE_BUG;
| AHD_PCIX_CHIPRST_BUG|AHD_PCIX_SCBRAM_RD_BUG
| AHD_PKTIZED_STATUS_BUG|AHD_PKT_LUN_BUG
| AHD_MDFF_WSCBPTR_BUG|AHD_REG_SLOW_SETTLE_BUG
| AHD_SET_MODE_BUG|AHD_BUSFREEREV_BUG
| AHD_NONPACKFIFO_BUG|AHD_PACED_NEGTABLE_BUG;
/*
* IO Cell paramter setup.
......
drivers/scsi/aic7xxx/aic79xx_proc.c
View file @ e1f5aa3d
......@@ -37,7 +37,7 @@
* String handling code courtesy of Gerard Roudier's <groudier@club-internet.fr>
* sym driver.
*
* $Id: //depot/aic7xxx/linux/drivers/scsi/aic7xxx/aic79xx_proc.c#12 $
* $Id: //depot/aic7xxx/linux/drivers/scsi/aic7xxx/aic79xx_proc.c#13 $
*/
#include "aic79xx_osm.h"
#include "aic79xx_inline.h"
......@@ -124,8 +124,12 @@ ahd_format_transinfo(struct info_str *info, struct ahd_transinfo *tinfo)
printed_options = 0;
copy_info(info, " (%d.%03dMHz", freq / 1000, freq % 1000);
if ((tinfo->ppr_options & MSG_EXT_PPR_RD_STRM) != 0) {
copy_info(info, " RDSTRM");
printed_options++;
}
if ((tinfo->ppr_options & MSG_EXT_PPR_DT_REQ) != 0) {
copy_info(info, " DT");
copy_info(info, "%s", printed_options ? "|DT" : " DT");
printed_options++;
}
if ((tinfo->ppr_options & MSG_EXT_PPR_IU_REQ) != 0) {
......
drivers/scsi/aic7xxx/aic79xx_reg.h_shipped
View file @ e1f5aa3d
......@@ -2,8 +2,8 @@
* DO NOT EDIT - This file is automatically generated
* from the following source files:
*
* $Id: //depot/aic7xxx/aic7xxx/aic79xx.seq#86 $
* $Id: //depot/aic7xxx/aic7xxx/aic79xx.reg#61 $
* $Id: //depot/aic7xxx/aic7xxx/aic79xx.seq#87 $
* $Id: //depot/aic7xxx/aic7xxx/aic79xx.reg#62 $
*/
typedef int (ahd_reg_print_t)(u_int, u_int *, u_int);
typedef struct ahd_reg_parse_entry {
......@@ -3638,13 +3638,14 @@ ahd_reg_print_t ahd_scb_disconnected_lists_print;
#define SCB_RESIDUAL_DATACNT 0x180
#define SCB_CDB_STORE 0x180
#define SCB_HOST_CDB_PTR 0x180
#define SCB_RESIDUAL_SGPTR 0x184
#define SCB_CDB_PTR 0x184
#define SG_ADDR_MASK 0xf8
#define SG_OVERRUN_RESID 0x02
#define SCB_SCSI_STATUS 0x188
#define SCB_HOST_CDB_LEN 0x188
#define SCB_TARGET_PHASES 0x189
......
drivers/scsi/aic7xxx/aic79xx_reg_print.c_shipped
View file @ e1f5aa3d
......@@ -2,8 +2,8 @@
* DO NOT EDIT - This file is automatically generated
* from the following source files:
*
* $Id: //depot/aic7xxx/aic7xxx/aic79xx.seq#86 $
* $Id: //depot/aic7xxx/aic7xxx/aic79xx.reg#61 $
* $Id: //depot/aic7xxx/aic7xxx/aic79xx.seq#87 $
* $Id: //depot/aic7xxx/aic7xxx/aic79xx.reg#62 $
*/
#include "aic79xx_osm.h"
......
drivers/scsi/aic7xxx/aic79xx_seq.h_shipped
View file @ e1f5aa3d
This diff is collapsed.
Markdown is supported
0% or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment
GitLab Nexedi Edition | About GitLab | About Nexedi | 沪ICP备2021021310号-2 | 沪ICP备2021021310号-7