Merge branch 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus

* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
  MIPS: Avoid spurious make includecheck message
  MIPS: VPE: Get rid of BKL.
  MIPS: VPE: Fix build after the credential changes a while ago.
  MIPS: Excite: Get rid of BKL.
  MIPS: Sibyte: Get rid of BKL.
  MIPS: BCM63xx: Add PCMCIA & Cardbus support.
  MIPS: MSP71xx: request_irq() failure ignored in msp_pcibios_config_access()
  MIPS: Decrease size of au1xxx_dbdma_pm_regs[][]
  MIPS: SMP: Inline arch_send_call_function_{single_ipi,ipi_mask}
  MIPS: SMP: Fix build.
  MIPS: MIPSxx SC: Avoid destructive invalidation on partial L2 cachelines.
  MIPS: Sibyte: Fix compilation error.
  MIPS: BCM1480: Re-apply patch lost due to bad resolution of merge conflict.
  MIPS: BCM63xx: Add serial driver for bcm63xx integrated UART.
  MIPS: Loongson2: Fix typo "enalbe" -> "enable"
  MIPS: SMTC: Remove duplicate structure field initialization
  MIPS: Remove duplicated #include
  MIPS: BCM63xx: Remove duplicated #include

arch/mips/alchemy/common/dbdma.c

@@ -175,7 +175,7 @@ static dbdev_tab_t dbdev_tab[] = {
 #define DBDEV_TAB_SIZE	ARRAY_SIZE(dbdev_tab)
 
 #ifdef CONFIG_PM
-static u32 au1xxx_dbdma_pm_regs[NUM_DBDMA_CHANS + 1][8];
+static u32 au1xxx_dbdma_pm_regs[NUM_DBDMA_CHANS + 1][6];
 #endif
 
 
@@ -993,14 +993,13 @@ void au1xxx_dbdma_suspend(void)
 	au1xxx_dbdma_pm_regs[0][3] = au_readl(addr + 0x0c);
 
 	/* save channel configurations */
-	for (i = 1, addr = DDMA_CHANNEL_BASE; i < NUM_DBDMA_CHANS; i++) {
+	for (i = 1, addr = DDMA_CHANNEL_BASE; i <= NUM_DBDMA_CHANS; i++) {
 		au1xxx_dbdma_pm_regs[i][0] = au_readl(addr + 0x00);
 		au1xxx_dbdma_pm_regs[i][1] = au_readl(addr + 0x04);
 		au1xxx_dbdma_pm_regs[i][2] = au_readl(addr + 0x08);
 		au1xxx_dbdma_pm_regs[i][3] = au_readl(addr + 0x0c);
 		au1xxx_dbdma_pm_regs[i][4] = au_readl(addr + 0x10);
 		au1xxx_dbdma_pm_regs[i][5] = au_readl(addr + 0x14);
-		au1xxx_dbdma_pm_regs[i][6] = au_readl(addr + 0x18);
 
 		/* halt channel */
 		au_writel(au1xxx_dbdma_pm_regs[i][0] & ~1, addr + 0x00);
@@ -1027,14 +1026,13 @@ void au1xxx_dbdma_resume(void)
 	au_writel(au1xxx_dbdma_pm_regs[0][3], addr + 0x0c);
 
 	/* restore channel configurations */
-	for (i = 1, addr = DDMA_CHANNEL_BASE; i < NUM_DBDMA_CHANS; i++) {
+	for (i = 1, addr = DDMA_CHANNEL_BASE; i <= NUM_DBDMA_CHANS; i++) {
 		au_writel(au1xxx_dbdma_pm_regs[i][0], addr + 0x00);
 		au_writel(au1xxx_dbdma_pm_regs[i][1], addr + 0x04);
 		au_writel(au1xxx_dbdma_pm_regs[i][2], addr + 0x08);
 		au_writel(au1xxx_dbdma_pm_regs[i][3], addr + 0x0c);
 		au_writel(au1xxx_dbdma_pm_regs[i][4], addr + 0x10);
 		au_writel(au1xxx_dbdma_pm_regs[i][5], addr + 0x14);
-		au_writel(au1xxx_dbdma_pm_regs[i][6], addr + 0x18);
 		au_sync();
 		addr += 0x100;	/* next channel base */
 	}

arch/mips/basler/excite/excite_iodev.c

@@ -112,10 +112,8 @@ static int iodev_open(struct inode *i, struct file *f)
 {
 	int ret;
 
-	lock_kernel();
 	ret = request_irq(iodev_irq, iodev_irqhdl, IRQF_DISABLED,
 			   iodev_name, &miscdev);
-	unlock_kernel();
 
 	return ret;
 }

arch/mips/bcm63xx/Makefile

 obj-y		+= clk.o cpu.o cs.o gpio.o irq.o prom.o setup.o timer.o \
-		   dev-dsp.o dev-enet.o
+		   dev-dsp.o dev-enet.o dev-pcmcia.o dev-uart.o
 obj-$(CONFIG_EARLY_PRINTK)	+= early_printk.o
 
 obj-y		+= boards/

arch/mips/bcm63xx/boards/board_bcm963xx.c

@@ -20,10 +20,11 @@
 #include <bcm63xx_cpu.h>
 #include <bcm63xx_regs.h>
 #include <bcm63xx_io.h>
-#include <bcm63xx_board.h>
 #include <bcm63xx_dev_pci.h>
 #include <bcm63xx_dev_enet.h>
 #include <bcm63xx_dev_dsp.h>
+#include <bcm63xx_dev_pcmcia.h>
+#include <bcm63xx_dev_uart.h>
 #include <board_bcm963xx.h>
 
 #define PFX	"board_bcm963xx: "
@@ -793,6 +794,11 @@ int __init board_register_devices(void)
 {
 	u32 val;
 
+	bcm63xx_uart_register();
+
+	if (board.has_pccard)
+		bcm63xx_pcmcia_register();
+
 	if (board.has_enet0 &&
 	    !board_get_mac_address(board.enet0.mac_addr))
 		bcm63xx_enet_register(0, &board.enet0);

arch/mips/bcm63xx/dev-pcmcia.c

+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2008 Maxime Bizon <mbizon@freebox.fr>
+ */
+
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <asm/bootinfo.h>
+#include <linux/platform_device.h>
+#include <bcm63xx_cs.h>
+#include <bcm63xx_cpu.h>
+#include <bcm63xx_dev_pcmcia.h>
+#include <bcm63xx_io.h>
+#include <bcm63xx_regs.h>
+
+static struct resource pcmcia_resources[] = {
+	/* pcmcia registers */
+	{
+		/* start & end filled at runtime */
+		.flags		= IORESOURCE_MEM,
+	},
+
+	/* pcmcia memory zone resources */
+	{
+		.start		= BCM_PCMCIA_COMMON_BASE_PA,
+		.end		= BCM_PCMCIA_COMMON_END_PA,
+		.flags		= IORESOURCE_MEM,
+	},
+	{
+		.start		= BCM_PCMCIA_ATTR_BASE_PA,
+		.end		= BCM_PCMCIA_ATTR_END_PA,
+		.flags		= IORESOURCE_MEM,
+	},
+	{
+		.start		= BCM_PCMCIA_IO_BASE_PA,
+		.end		= BCM_PCMCIA_IO_END_PA,
+		.flags		= IORESOURCE_MEM,
+	},
+
+	/* PCMCIA irq */
+	{
+		/* start filled at runtime */
+		.flags		= IORESOURCE_IRQ,
+	},
+
+	/* declare PCMCIA IO resource also */
+	{
+		.start		= BCM_PCMCIA_IO_BASE_PA,
+		.end		= BCM_PCMCIA_IO_END_PA,
+		.flags		= IORESOURCE_IO,
+	},
+};
+
+static struct bcm63xx_pcmcia_platform_data pd;
+
+static struct platform_device bcm63xx_pcmcia_device = {
+	.name		= "bcm63xx_pcmcia",
+	.id		= 0,
+	.num_resources	= ARRAY_SIZE(pcmcia_resources),
+	.resource	= pcmcia_resources,
+	.dev		= {
+		.platform_data = &pd,
+	},
+};
+
+static int __init config_pcmcia_cs(unsigned int cs,
+				   u32 base, unsigned int size)
+{
+	int ret;
+
+	ret = bcm63xx_set_cs_status(cs, 0);
+	if (!ret)
+		ret = bcm63xx_set_cs_base(cs, base, size);
+	if (!ret)
+		ret = bcm63xx_set_cs_status(cs, 1);
+	return ret;
+}
+
+static const __initdata struct {
+	unsigned int	cs;
+	unsigned int	base;
+	unsigned int	size;
+} pcmcia_cs[3] = {
+	{
+		.cs	= MPI_CS_PCMCIA_COMMON,
+		.base	= BCM_PCMCIA_COMMON_BASE_PA,
+		.size	= BCM_PCMCIA_COMMON_SIZE
+	},
+	{
+		.cs	= MPI_CS_PCMCIA_ATTR,
+		.base	= BCM_PCMCIA_ATTR_BASE_PA,
+		.size	= BCM_PCMCIA_ATTR_SIZE
+	},
+	{
+		.cs	= MPI_CS_PCMCIA_IO,
+		.base	= BCM_PCMCIA_IO_BASE_PA,
+		.size	= BCM_PCMCIA_IO_SIZE
+	},
+};
+
+int __init bcm63xx_pcmcia_register(void)
+{
+	int ret, i;
+
+	if (!BCMCPU_IS_6348() && !BCMCPU_IS_6358())
+		return 0;
+
+	/* use correct pcmcia ready gpio depending on processor */
+	switch (bcm63xx_get_cpu_id()) {
+	case BCM6348_CPU_ID:
+		pd.ready_gpio = 22;
+		break;
+
+	case BCM6358_CPU_ID:
+		pd.ready_gpio = 18;
+		break;
+
+	default:
+		return -ENODEV;
+	}
+
+	pcmcia_resources[0].start = bcm63xx_regset_address(RSET_PCMCIA);
+	pcmcia_resources[0].end = pcmcia_resources[0].start +
+		RSET_PCMCIA_SIZE - 1;
+	pcmcia_resources[4].start = bcm63xx_get_irq_number(IRQ_PCMCIA);
+
+	/* configure pcmcia chip selects */
+	for (i = 0; i < 3; i++) {
+		ret = config_pcmcia_cs(pcmcia_cs[i].cs,
+				       pcmcia_cs[i].base,
+				       pcmcia_cs[i].size);
+		if (ret)
+			goto out_err;
+	}
+
+	return platform_device_register(&bcm63xx_pcmcia_device);
+
+out_err:
+	printk(KERN_ERR "unable to set pcmcia chip select\n");
+	return ret;
+}

arch/mips/bcm63xx/dev-uart.c

+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2008 Maxime Bizon <mbizon@freebox.fr>
+ */
+
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/platform_device.h>
+#include <bcm63xx_cpu.h>
+#include <bcm63xx_dev_uart.h>
+
+static struct resource uart_resources[] = {
+	{
+		.start		= -1, /* filled at runtime */
+		.end		= -1, /* filled at runtime */
+		.flags		= IORESOURCE_MEM,
+	},
+	{
+		.start		= -1, /* filled at runtime */
+		.flags		= IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device bcm63xx_uart_device = {
+	.name		= "bcm63xx_uart",
+	.id		= 0,
+	.num_resources	= ARRAY_SIZE(uart_resources),
+	.resource	= uart_resources,
+};
+
+int __init bcm63xx_uart_register(void)
+{
+	uart_resources[0].start = bcm63xx_regset_address(RSET_UART0);
+	uart_resources[0].end = uart_resources[0].start;
+	uart_resources[0].end += RSET_UART_SIZE - 1;
+	uart_resources[1].start = bcm63xx_get_irq_number(IRQ_UART0);
+	return platform_device_register(&bcm63xx_uart_device);
+}

arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_pcmcia.h

+#ifndef BCM63XX_DEV_PCMCIA_H_
+#define BCM63XX_DEV_PCMCIA_H_
+
+/*
+ * PCMCIA driver platform data
+ */
+struct bcm63xx_pcmcia_platform_data {
+	unsigned int ready_gpio;
+};
+
+int bcm63xx_pcmcia_register(void);
+
+#endif /* BCM63XX_DEV_PCMCIA_H_ */

arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_uart.h

+#ifndef BCM63XX_DEV_UART_H_
+#define BCM63XX_DEV_UART_H_
+
+int bcm63xx_uart_register(void);
+
+#endif /* BCM63XX_DEV_UART_H_ */

arch/mips/include/asm/smp.h

@@ -77,7 +77,18 @@ extern void play_dead(void);
 
 extern asmlinkage void smp_call_function_interrupt(void);
 
-extern void arch_send_call_function_single_ipi(int cpu);
-extern void arch_send_call_function_ipi_mask(const struct cpumask *mask);
+static inline void arch_send_call_function_single_ipi(int cpu)
+{
+	extern struct plat_smp_ops *mp_ops;     /* private */
+
+	mp_ops->send_ipi_mask(&cpumask_of_cpu(cpu), SMP_CALL_FUNCTION);
+}
+
+static inline void arch_send_call_function_ipi_mask(const struct cpumask *mask)
+{
+	extern struct plat_smp_ops *mp_ops;     /* private */
+
+	mp_ops->send_ipi_mask(mask, SMP_CALL_FUNCTION);
+}
 
 #endif /* __ASM_SMP_H */

arch/mips/include/asm/unaligned.h

@@ -12,17 +12,17 @@
 #if defined(__MIPSEB__)
 # include <linux/unaligned/be_struct.h>
 # include <linux/unaligned/le_byteshift.h>
-# include <linux/unaligned/generic.h>
 # define get_unaligned	__get_unaligned_be
 # define put_unaligned	__put_unaligned_be
 #elif defined(__MIPSEL__)
 # include <linux/unaligned/le_struct.h>
 # include <linux/unaligned/be_byteshift.h>
-# include <linux/unaligned/generic.h>
 # define get_unaligned	__get_unaligned_le
 # define put_unaligned	__put_unaligned_le
 #else
 #  error "MIPS, but neither __MIPSEB__, nor __MIPSEL__???"
 #endif
 
+# include <linux/unaligned/generic.h>
+
 #endif /* _ASM_MIPS_UNALIGNED_H */

arch/mips/kernel/kspd.c

@@ -172,13 +172,20 @@ static unsigned int translate_open_flags(int flags)
 }
 
 
-static void sp_setfsuidgid( uid_t uid, gid_t gid)
+static int sp_setfsuidgid(uid_t uid, gid_t gid)
 {
-	current->cred->fsuid = uid;
-	current->cred->fsgid = gid;
+	struct cred *new;
 
-	key_fsuid_changed(current);
-	key_fsgid_changed(current);
+	new = prepare_creds();
+	if (!new)
+		return -ENOMEM;
+
+	new->fsuid = uid;
+	new->fsgid = gid;
+
+	commit_creds(new);
+
+	return 0;
 }
 
 /*
@@ -196,7 +203,7 @@ void sp_work_handle_request(void)
 	mm_segment_t old_fs;
 	struct timeval tv;
 	struct timezone tz;
-	int cmd;
+	int err, cmd;
 
 	char *vcwd;
 	int size;
@@ -225,8 +232,11 @@ void sp_work_handle_request(void)
 	/* Run the syscall at the privilege of the user who loaded the
 	   SP program */
 
-	if (vpe_getuid(tclimit))
-		sp_setfsuidgid(vpe_getuid(tclimit), vpe_getgid(tclimit));
+	if (vpe_getuid(tclimit)) {
+		err = sp_setfsuidgid(vpe_getuid(tclimit), vpe_getgid(tclimit));
+		if (!err)
+			pr_err("Change of creds failed\n");
+	}
 
 	switch (sc.cmd) {
 	/* needs the flags argument translating from SDE kit to
@@ -283,8 +293,11 @@ void sp_work_handle_request(void)
 		break;
  	} /* switch */
 
-	if (vpe_getuid(tclimit))
-		sp_setfsuidgid( 0, 0);
+	if (vpe_getuid(tclimit)) {
+		err = sp_setfsuidgid(0, 0);
+		if (!err)
+			pr_err("restoring old creds failed\n");
+	}
 
 	old_fs = get_fs();
 	set_fs(KERNEL_DS);

arch/mips/kernel/rtlx.c

@@ -72,8 +72,9 @@ static void rtlx_dispatch(void)
 */
 static irqreturn_t rtlx_interrupt(int irq, void *dev_id)
 {
+	unsigned int vpeflags;
+	unsigned long flags;
 	int i;
-	unsigned int flags, vpeflags;
 
 	/* Ought not to be strictly necessary for SMTC builds */
 	local_irq_save(flags);
@@ -392,20 +393,12 @@ ssize_t rtlx_write(int index, const void __user *buffer, size_t count)
 
 static int file_open(struct inode *inode, struct file *filp)
 {
-	int minor = iminor(inode);
-	int err;
-
-	lock_kernel();
-	err = rtlx_open(minor, (filp->f_flags & O_NONBLOCK) ? 0 : 1);
-	unlock_kernel();
-	return err;
+	return rtlx_open(iminor(inode), (filp->f_flags & O_NONBLOCK) ? 0 : 1);
 }
 
 static int file_release(struct inode *inode, struct file *filp)
 {
-	int minor = iminor(inode);
-
-	return rtlx_release(minor);
+	return rtlx_release(iminor(inode));
 }
 
 static unsigned int file_poll(struct file *file, poll_table * wait)

arch/mips/kernel/smp.c

@@ -32,7 +32,6 @@
 #include <linux/cpumask.h>
 #include <linux/cpu.h>
 #include <linux/err.h>
-#include <linux/smp.h>
 
 #include <asm/atomic.h>
 #include <asm/cpu.h>
@@ -128,19 +127,6 @@ asmlinkage __cpuinit void start_secondary(void)
 	cpu_idle();
 }
 
-void arch_send_call_function_ipi_mask(const struct cpumask *mask)
-{
-	mp_ops->send_ipi_mask(mask, SMP_CALL_FUNCTION);
-}
-
-/*
- * We reuse the same vector for the single IPI
- */
-void arch_send_call_function_single_ipi(int cpu)
-{
-	mp_ops->send_ipi_mask(cpumask_of_cpu(cpu), SMP_CALL_FUNCTION);
-}
-
 /*
  * Call into both interrupt handlers, as we share the IPI for them
  */

arch/mips/kernel/smtc.c

@@ -1098,9 +1098,8 @@ static void ipi_irq_dispatch(void)
 
 static struct irqaction irq_ipi = {
 	.handler	= ipi_interrupt,
-	.flags		= IRQF_DISABLED,
-	.name		= "SMTC_IPI",
-	.flags		= IRQF_PERCPU
+	.flags		= IRQF_DISABLED | IRQF_PERCPU,
+	.name		= "SMTC_IPI"
 };
 
 static void setup_cross_vpe_interrupts(unsigned int nvpe)

arch/mips/kernel/vpe.c

@@ -144,13 +144,14 @@ struct tc {
 };
 
 struct {
-	/* Virtual processing elements */
-	struct list_head vpe_list;
-
-	/* Thread contexts */
-	struct list_head tc_list;
+	spinlock_t vpe_list_lock;
+	struct list_head vpe_list;	/* Virtual processing elements */
+	spinlock_t tc_list_lock;
+	struct list_head tc_list;	/* Thread contexts */
 } vpecontrol = {
+	.vpe_list_lock	= SPIN_LOCK_UNLOCKED,
 	.vpe_list	= LIST_HEAD_INIT(vpecontrol.vpe_list),
+	.tc_list_lock	= SPIN_LOCK_UNLOCKED,
 	.tc_list	= LIST_HEAD_INIT(vpecontrol.tc_list)
 };
 
@@ -159,28 +160,38 @@ static void release_progmem(void *ptr);
 /* get the vpe associated with this minor */
 static struct vpe *get_vpe(int minor)
 {
-	struct vpe *v;
+	struct vpe *res, *v;
 
 	if (!cpu_has_mipsmt)
 		return NULL;
 
+	res = NULL;
+	spin_lock(&vpecontrol.vpe_list_lock);
 	list_for_each_entry(v, &vpecontrol.vpe_list, list) {
-		if (v->minor == minor)
-			return v;
+		if (v->minor == minor) {
+			res = v;
+			break;
 		}
+	}
+	spin_unlock(&vpecontrol.vpe_list_lock);
 
-	return NULL;
+	return res;
 }
 
 /* get the vpe associated with this minor */
 static struct tc *get_tc(int index)
 {
-	struct tc *t;
+	struct tc *res, *t;
 
+	res = NULL;
+	spin_lock(&vpecontrol.tc_list_lock);
 	list_for_each_entry(t, &vpecontrol.tc_list, list) {
-		if (t->index == index)
-			return t;
+		if (t->index == index) {
+			res = t;
+			break;
+		}
 	}
+	spin_unlock(&vpecontrol.tc_list_lock);
 
 	return NULL;
 }
@@ -190,15 +201,17 @@ static struct vpe *alloc_vpe(int minor)
 {
 	struct vpe *v;
 
-	if ((v = kzalloc(sizeof(struct vpe), GFP_KERNEL)) == NULL) {
+	if ((v = kzalloc(sizeof(struct vpe), GFP_KERNEL)) == NULL)
 		return NULL;
-	}
 
 	INIT_LIST_HEAD(&v->tc);
+	spin_lock(&vpecontrol.vpe_list_lock);
 	list_add_tail(&v->list, &vpecontrol.vpe_list);
+	spin_unlock(&vpecontrol.vpe_list_lock);
 
 	INIT_LIST_HEAD(&v->notify);
 	v->minor = minor;
+
 	return v;
 }
 
@@ -212,7 +225,10 @@ static struct tc *alloc_tc(int index)
 
 	INIT_LIST_HEAD(&tc->tc);
 	tc->index = index;
+
+	spin_lock(&vpecontrol.tc_list_lock);
 	list_add_tail(&tc->list, &vpecontrol.tc_list);
+	spin_unlock(&vpecontrol.tc_list_lock);
 
 out:
 	return tc;
@@ -227,7 +243,7 @@ static void release_vpe(struct vpe *v)
 	kfree(v);
 }
 
-static void dump_mtregs(void)
+static void __maybe_unused dump_mtregs(void)
 {
 	unsigned long val;
 
@@ -1048,20 +1064,19 @@ static int vpe_open(struct inode *inode, struct file *filp)
 	enum vpe_state state;
 	struct vpe_notifications *not;
 	struct vpe *v;
-	int ret, err = 0;
+	int ret;
 
-	lock_kernel();
 	if (minor != iminor(inode)) {
 		/* assume only 1 device at the moment. */
-		printk(KERN_WARNING "VPE loader: only vpe1 is supported\n");
-		err = -ENODEV;
-		goto out;
+		pr_warning("VPE loader: only vpe1 is supported\n");
+
+		return -ENODEV;
 	}
 
 	if ((v = get_vpe(tclimit)) == NULL) {
-		printk(KERN_WARNING "VPE loader: unable to get vpe\n");
-		err = -ENODEV;
-		goto out;
+		pr_warning("VPE loader: unable to get vpe\n");
+
+		return -ENODEV;
 	}
 
 	state = xchg(&v->state, VPE_STATE_INUSE);
@@ -1101,8 +1116,8 @@ static int vpe_open(struct inode *inode, struct file *filp)
 	v->shared_ptr = NULL;
 	v->__start = 0;
 
-out:
 	unlock_kernel();
+
 	return 0;
 }
 
@@ -1594,14 +1609,14 @@ static void __exit vpe_module_exit(void)
 {
 	struct vpe *v, *n;
 
+	device_del(&vpe_device);
+	unregister_chrdev(major, module_name);
+
+	/* No locking needed here */
 	list_for_each_entry_safe(v, n, &vpecontrol.vpe_list, list) {
-		if (v->state != VPE_STATE_UNUSED) {
+		if (v->state != VPE_STATE_UNUSED)
 			release_vpe(v);
 	}
-	}
-
-	device_del(&vpe_device);
-	unregister_chrdev(major, module_name);
 }
 
 module_init(vpe_module_init);

arch/mips/mm/sc-mips.c

@@ -32,6 +32,11 @@ static void mips_sc_wback_inv(unsigned long addr, unsigned long size)
  */
 static void mips_sc_inv(unsigned long addr, unsigned long size)
 {
+	unsigned long lsize = cpu_scache_line_size();
+	unsigned long almask = ~(lsize - 1);
+
+	cache_op(Hit_Writeback_Inv_SD, addr & almask);
+	cache_op(Hit_Writeback_Inv_SD, (addr + size - 1) & almask);
 	blast_inv_scache_range(addr, addr + size);
 }
 

arch/mips/oprofile/op_model_loongson2.c

@@ -44,7 +44,7 @@ static struct loongson2_register_config {
 	unsigned int ctrl;
 	unsigned long long reset_counter1;
 	unsigned long long reset_counter2;
-	int cnt1_enalbed, cnt2_enalbed;
+	int cnt1_enabled, cnt2_enabled;
 } reg;
 
 DEFINE_SPINLOCK(sample_lock);
@@ -81,8 +81,8 @@ static void loongson2_reg_setup(struct op_counter_config *cfg)
 
 	reg.ctrl = ctrl;
 
-	reg.cnt1_enalbed = cfg[0].enabled;
-	reg.cnt2_enalbed = cfg[1].enabled;
+	reg.cnt1_enabled = cfg[0].enabled;
+	reg.cnt2_enabled = cfg[1].enabled;
 
 }
 
@@ -99,7 +99,7 @@ static void loongson2_cpu_setup(void *args)
 static void loongson2_cpu_start(void *args)
 {
 	/* Start all counters on current CPU */
-	if (reg.cnt1_enalbed || reg.cnt2_enalbed)
+	if (reg.cnt1_enabled || reg.cnt2_enabled)
 		write_c0_perfctrl(reg.ctrl);
 }
 
@@ -125,7 +125,7 @@ static irqreturn_t loongson2_perfcount_handler(int irq, void *dev_id)
 	 */
 
 	/* Check whether the irq belongs to me */
-	enabled = reg.cnt1_enalbed | reg.cnt2_enalbed;
+	enabled = reg.cnt1_enabled | reg.cnt2_enabled;
 	if (!enabled)
 		return IRQ_NONE;
 
@@ -136,12 +136,12 @@ static irqreturn_t loongson2_perfcount_handler(int irq, void *dev_id)
 	spin_lock_irqsave(&sample_lock, flags);
 
 	if (counter1 & LOONGSON2_PERFCNT_OVERFLOW) {
-		if (reg.cnt1_enalbed)
+		if (reg.cnt1_enabled)
 			oprofile_add_sample(regs, 0);
 		counter1 = reg.reset_counter1;
 	}
 	if (counter2 & LOONGSON2_PERFCNT_OVERFLOW) {
-		if (reg.cnt2_enalbed)
+		if (reg.cnt2_enabled)
 			oprofile_add_sample(regs, 1);
 		counter2 = reg.reset_counter2;
 	}

arch/mips/pci/ops-pmcmsp.c

@@ -385,6 +385,7 @@ int msp_pcibios_config_access(unsigned char access_type,
 	unsigned long intr;
 	unsigned long value;
 	static char pciirqflag;
+	int ret;
 #if defined(CONFIG_PMC_MSP7120_GW) || defined(CONFIG_PMC_MSP7120_EVAL)
 	unsigned int	vpe_status;
 #endif
@@ -402,11 +403,13 @@ int msp_pcibios_config_access(unsigned char access_type,
 	 * allocation assigns an interrupt handler to the interrupt.
 	 */
 	if (pciirqflag == 0) {
-		request_irq(MSP_INT_PCI,/* Hardcoded internal MSP7120 wiring */
+		ret = request_irq(MSP_INT_PCI,/* Hardcoded internal MSP7120 wiring */
 				bpci_interrupt,
 				IRQF_SHARED | IRQF_DISABLED,
 				"PMC MSP PCI Host",
 				preg);
+		if (ret != 0)
+			return ret;
 		pciirqflag = ~0;
 	}
 

arch/mips/sgi-ip27/ip27-smp.c

@@ -165,7 +165,7 @@ static void ip27_send_ipi_single(int destid, unsigned int action)
 	REMOTE_HUB_SEND_INTR(COMPACT_TO_NASID_NODEID(cpu_to_node(destid)), irq);
 }
 
-static void ip27_send_ipi(const struct cpumask *mask, unsigned int action)
+static void ip27_send_ipi_mask(const struct cpumask *mask, unsigned int action)
 {
 	unsigned int i;
 

arch/mips/sibyte/bcm1480/irq.c

@@ -117,10 +117,6 @@ static int bcm1480_set_affinity(unsigned int irq, const struct cpumask *mask)
 	unsigned long flags;
 	unsigned int irq_dirty;
 
-	if (cpumask_weight(mask) != 1) {
-		printk("attempted to set irq affinity for irq %d to multiple CPUs\n", irq);
-		return -1;
-	}
 	i = cpumask_first(mask);
 
 	/* Convert logical CPU to physical CPU */

arch/mips/sibyte/common/sb_tbprof.c

@@ -403,36 +403,31 @@ static int sbprof_zbprof_stop(void)
 static int sbprof_tb_open(struct inode *inode, struct file *filp)
 {
 	int minor;
-	int err = 0;
 
-	lock_kernel();
 	minor = iminor(inode);
-	if (minor != 0) {
-		err = -ENODEV;
-		goto out;
-	}
+	if (minor != 0)
+		return -ENODEV;
 
-	if (xchg(&sbp.open, SB_OPENING) != SB_CLOSED) {
-		err = -EBUSY;
-		goto out;
-	}
+	if (xchg(&sbp.open, SB_OPENING) != SB_CLOSED)
+		return -EBUSY;
 
 	memset(&sbp, 0, sizeof(struct sbprof_tb));
 	sbp.sbprof_tbbuf = vmalloc(MAX_TBSAMPLE_BYTES);
 	if (!sbp.sbprof_tbbuf) {
-		err = -ENOMEM;
-		goto out;
+		sbp.open = SB_CLOSED;
+		wmb();
+		return -ENOMEM;
 	}
+
 	memset(sbp.sbprof_tbbuf, 0, MAX_TBSAMPLE_BYTES);
 	init_waitqueue_head(&sbp.tb_sync);
 	init_waitqueue_head(&sbp.tb_read);
 	mutex_init(&sbp.lock);
 
 	sbp.open = SB_OPEN;
+	wmb();
 
-  out:
-	unlock_kernel();
-	return err;
+	return 0;
 }
 
 static int sbprof_tb_release(struct inode *inode, struct file *filp)
@@ -440,7 +435,7 @@ static int sbprof_tb_release(struct inode *inode, struct file *filp)
 	int minor;
 
 	minor = iminor(inode);
-	if (minor != 0 || !sbp.open)
+	if (minor != 0 || sbp.open != SB_CLOSED)
 		return -ENODEV;
 
 	mutex_lock(&sbp.lock);
@@ -449,7 +444,8 @@ static int sbprof_tb_release(struct inode *inode, struct file *filp)
 		sbprof_zbprof_stop();
 
 	vfree(sbp.sbprof_tbbuf);
-	sbp.open = 0;
+	sbp.open = SB_CLOSED;
+	wmb();
 
 	mutex_unlock(&sbp.lock);
 
@@ -583,7 +579,8 @@ static int __init sbprof_tb_init(void)
 	}
 	tb_dev = dev;
 
-	sbp.open = 0;
+	sbp.open = SB_CLOSED;
+	wmb();
 	tb_period = zbbus_mhz * 10000LL;
 	pr_info(DEVNAME ": initialized - tb_period = %lld\n",
 		(long long) tb_period);

arch/mips/sibyte/swarm/setup.c

@@ -106,7 +106,7 @@ void read_persistent_clock(struct timespec *ts)
 		break;
 	}
 	ts->tv_sec = sec;
-	tv->tv_nsec = 0;
+	ts->tv_nsec = 0;
 }
 
 int rtc_mips_set_time(unsigned long sec)

drivers/pcmcia/Kconfig

@@ -192,6 +192,10 @@ config PCMCIA_AU1X00
 	tristate "Au1x00 pcmcia support"
 	depends on SOC_AU1X00 && PCMCIA
 
+config PCMCIA_BCM63XX
+	tristate "bcm63xx pcmcia support"
+	depends on BCM63XX && PCMCIA
+
 config PCMCIA_SA1100
 	tristate "SA1100 support"
 	depends on ARM && ARCH_SA1100 && PCMCIA

drivers/pcmcia/Makefile

@@ -27,6 +27,7 @@ obj-$(CONFIG_PCMCIA_SA1111)			+= sa11xx_core.o sa1111_cs.o
 obj-$(CONFIG_M32R_PCC)				+= m32r_pcc.o
 obj-$(CONFIG_M32R_CFC)				+= m32r_cfc.o
 obj-$(CONFIG_PCMCIA_AU1X00)			+= au1x00_ss.o
+obj-$(CONFIG_PCMCIA_BCM63XX)			+= bcm63xx_pcmcia.o
 obj-$(CONFIG_PCMCIA_VRC4171)			+= vrc4171_card.o
 obj-$(CONFIG_PCMCIA_VRC4173)			+= vrc4173_cardu.o
 obj-$(CONFIG_OMAP_CF)				+= omap_cf.o

drivers/pcmcia/bcm63xx_pcmcia.c

+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2008 Maxime Bizon <mbizon@freebox.fr>
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/ioport.h>
+#include <linux/timer.h>
+#include <linux/platform_device.h>
+#include <linux/delay.h>
+#include <linux/pci.h>
+#include <linux/gpio.h>
+
+#include <bcm63xx_regs.h>
+#include <bcm63xx_io.h>
+#include "bcm63xx_pcmcia.h"
+
+#define PFX	"bcm63xx_pcmcia: "
+
+#ifdef CONFIG_CARDBUS
+/* if cardbus is used, platform device needs reference to actual pci
+ * device */
+static struct pci_dev *bcm63xx_cb_dev;
+#endif
+
+/*
+ * read/write helper for pcmcia regs
+ */
+static inline u32 pcmcia_readl(struct bcm63xx_pcmcia_socket *skt, u32 off)
+{
+	return bcm_readl(skt->base + off);
+}
+
+static inline void pcmcia_writel(struct bcm63xx_pcmcia_socket *skt,
+				 u32 val, u32 off)
+{
+	bcm_writel(val, skt->base + off);
+}
+
+/*
+ * This callback should (re-)initialise the socket, turn on status
+ * interrupts and PCMCIA bus, and wait for power to stabilise so that
+ * the card status signals report correctly.
+ *
+ * Hardware cannot do that.
+ */
+static int bcm63xx_pcmcia_sock_init(struct pcmcia_socket *sock)
+{
+	return 0;
+}
+
+/*
+ * This callback should remove power on the socket, disable IRQs from
+ * the card, turn off status interrupts, and disable the PCMCIA bus.
+ *
+ * Hardware cannot do that.
+ */
+static int bcm63xx_pcmcia_suspend(struct pcmcia_socket *sock)
+{
+	return 0;
+}
+
+/*
+ * Implements the set_socket() operation for the in-kernel PCMCIA
+ * service (formerly SS_SetSocket in Card Services). We more or
+ * less punt all of this work and let the kernel handle the details
+ * of power configuration, reset, &c. We also record the value of
+ * `state' in order to regurgitate it to the PCMCIA core later.
+ */
+static int bcm63xx_pcmcia_set_socket(struct pcmcia_socket *sock,
+				     socket_state_t *state)
+{
+	struct bcm63xx_pcmcia_socket *skt;
+	unsigned long flags;
+	u32 val;
+
+	skt = sock->driver_data;
+
+	spin_lock_irqsave(&skt->lock, flags);
+
+	/* note: hardware cannot control socket power, so we will
+	 * always report SS_POWERON */
+
+	/* apply socket reset */
+	val = pcmcia_readl(skt, PCMCIA_C1_REG);
+	if (state->flags & SS_RESET)
+		val |= PCMCIA_C1_RESET_MASK;
+	else
+		val &= ~PCMCIA_C1_RESET_MASK;
+
+	/* reverse reset logic for cardbus card */
+	if (skt->card_detected && (skt->card_type & CARD_CARDBUS))
+		val ^= PCMCIA_C1_RESET_MASK;
+
+	pcmcia_writel(skt, val, PCMCIA_C1_REG);
+
+	/* keep requested state for event reporting */
+	skt->requested_state = *state;
+
+	spin_unlock_irqrestore(&skt->lock, flags);
+
+	return 0;
+}
+
+/*
+ * identity cardtype from VS[12] input, CD[12] input while only VS2 is
+ * floating, and CD[12] input while only VS1 is floating
+ */
+enum {
+	IN_VS1 = (1 << 0),
+	IN_VS2 = (1 << 1),
+	IN_CD1_VS2H = (1 << 2),
+	IN_CD2_VS2H = (1 << 3),
+	IN_CD1_VS1H = (1 << 4),
+	IN_CD2_VS1H = (1 << 5),
+};
+
+static const u8 vscd_to_cardtype[] = {
+
+	/* VS1 float, VS2 float */
+	[IN_VS1 | IN_VS2] = (CARD_PCCARD | CARD_5V),
+
+	/* VS1 grounded, VS2 float */
+	[IN_VS2] = (CARD_PCCARD | CARD_5V | CARD_3V),
+
+	/* VS1 grounded, VS2 grounded */
+	[0] = (CARD_PCCARD | CARD_5V | CARD_3V | CARD_XV),
+
+	/* VS1 tied to CD1, VS2 float */
+	[IN_VS1 | IN_VS2 | IN_CD1_VS1H] = (CARD_CARDBUS | CARD_3V),
+
+	/* VS1 grounded, VS2 tied to CD2 */
+	[IN_VS2 | IN_CD2_VS2H] = (CARD_CARDBUS | CARD_3V | CARD_XV),
+
+	/* VS1 tied to CD2, VS2 grounded */
+	[IN_VS1 | IN_CD2_VS1H] = (CARD_CARDBUS | CARD_3V | CARD_XV | CARD_YV),
+
+	/* VS1 float, VS2 grounded */
+	[IN_VS1] = (CARD_PCCARD | CARD_XV),
+
+	/* VS1 float, VS2 tied to CD2 */
+	[IN_VS1 | IN_VS2 | IN_CD2_VS2H] = (CARD_CARDBUS | CARD_3V),
+
+	/* VS1 float, VS2 tied to CD1 */
+	[IN_VS1 | IN_VS2 | IN_CD1_VS2H] = (CARD_CARDBUS | CARD_XV | CARD_YV),
+
+	/* VS1 tied to CD2, VS2 float */
+	[IN_VS1 | IN_VS2 | IN_CD2_VS1H] = (CARD_CARDBUS | CARD_YV),
+
+	/* VS2 grounded, VS1 is tied to CD1, CD2 is grounded */
+	[IN_VS1 | IN_CD1_VS1H] = 0, /* ignore cardbay */
+};
+
+/*
+ * poll hardware to check card insertion status
+ */
+static unsigned int __get_socket_status(struct bcm63xx_pcmcia_socket *skt)
+{
+	unsigned int stat;
+	u32 val;
+
+	stat = 0;
+
+	/* check CD for card presence */
+	val = pcmcia_readl(skt, PCMCIA_C1_REG);
+
+	if (!(val & PCMCIA_C1_CD1_MASK) && !(val & PCMCIA_C1_CD2_MASK))
+		stat |= SS_DETECT;
+
+	/* if new insertion, detect cardtype */
+	if ((stat & SS_DETECT) && !skt->card_detected) {
+		unsigned int stat = 0;
+
+		/* float VS1, float VS2 */
+		val |= PCMCIA_C1_VS1OE_MASK;
+		val |= PCMCIA_C1_VS2OE_MASK;
+		pcmcia_writel(skt, val, PCMCIA_C1_REG);
+
+		/* wait for output to stabilize and read VS[12] */
+		udelay(10);
+		val = pcmcia_readl(skt, PCMCIA_C1_REG);
+		stat |= (val & PCMCIA_C1_VS1_MASK) ? IN_VS1 : 0;
+		stat |= (val & PCMCIA_C1_VS2_MASK) ? IN_VS2 : 0;
+
+		/* drive VS1 low, float VS2 */
+		val &= ~PCMCIA_C1_VS1OE_MASK;
+		val |= PCMCIA_C1_VS2OE_MASK;
+		pcmcia_writel(skt, val, PCMCIA_C1_REG);
+
+		/* wait for output to stabilize and read CD[12] */
+		udelay(10);
+		val = pcmcia_readl(skt, PCMCIA_C1_REG);
+		stat |= (val & PCMCIA_C1_CD1_MASK) ? IN_CD1_VS2H : 0;
+		stat |= (val & PCMCIA_C1_CD2_MASK) ? IN_CD2_VS2H : 0;
+
+		/* float VS1, drive VS2 low */
+		val |= PCMCIA_C1_VS1OE_MASK;
+		val &= ~PCMCIA_C1_VS2OE_MASK;
+		pcmcia_writel(skt, val, PCMCIA_C1_REG);
+
+		/* wait for output to stabilize and read CD[12] */
+		udelay(10);
+		val = pcmcia_readl(skt, PCMCIA_C1_REG);
+		stat |= (val & PCMCIA_C1_CD1_MASK) ? IN_CD1_VS1H : 0;
+		stat |= (val & PCMCIA_C1_CD2_MASK) ? IN_CD2_VS1H : 0;
+
+		/* guess cardtype from all this */
+		skt->card_type = vscd_to_cardtype[stat];
+		if (!skt->card_type)
+			dev_err(&skt->socket.dev, "unsupported card type\n");
+
+		/* drive both VS pin to 0 again */
+		val &= ~(PCMCIA_C1_VS1OE_MASK | PCMCIA_C1_VS2OE_MASK);
+
+		/* enable correct logic */
+		val &= ~(PCMCIA_C1_EN_PCMCIA_MASK | PCMCIA_C1_EN_CARDBUS_MASK);
+		if (skt->card_type & CARD_PCCARD)
+			val |= PCMCIA_C1_EN_PCMCIA_MASK;
+		else
+			val |= PCMCIA_C1_EN_CARDBUS_MASK;
+
+		pcmcia_writel(skt, val, PCMCIA_C1_REG);
+	}
+	skt->card_detected = (stat & SS_DETECT) ? 1 : 0;
+
+	/* report card type/voltage */
+	if (skt->card_type & CARD_CARDBUS)
+		stat |= SS_CARDBUS;
+	if (skt->card_type & CARD_3V)
+		stat |= SS_3VCARD;
+	if (skt->card_type & CARD_XV)
+		stat |= SS_XVCARD;
+	stat |= SS_POWERON;
+
+	if (gpio_get_value(skt->pd->ready_gpio))
+		stat |= SS_READY;
+
+	return stat;
+}
+
+/*
+ * core request to get current socket status
+ */
+static int bcm63xx_pcmcia_get_status(struct pcmcia_socket *sock,
+				     unsigned int *status)
+{
+	struct bcm63xx_pcmcia_socket *skt;
+
+	skt = sock->driver_data;
+
+	spin_lock_bh(&skt->lock);
+	*status = __get_socket_status(skt);
+	spin_unlock_bh(&skt->lock);
+
+	return 0;
+}
+
+/*
+ * socket polling timer callback
+ */
+static void bcm63xx_pcmcia_poll(unsigned long data)
+{
+	struct bcm63xx_pcmcia_socket *skt;
+	unsigned int stat, events;
+
+	skt = (struct bcm63xx_pcmcia_socket *)data;
+
+	spin_lock_bh(&skt->lock);
+
+	stat = __get_socket_status(skt);
+
+	/* keep only changed bits, and mask with required one from the
+	 * core */
+	events = (stat ^ skt->old_status) & skt->requested_state.csc_mask;
+	skt->old_status = stat;
+	spin_unlock_bh(&skt->lock);
+
+	if (events)
+		pcmcia_parse_events(&skt->socket, events);
+
+	mod_timer(&skt->timer,
+		  jiffies + msecs_to_jiffies(BCM63XX_PCMCIA_POLL_RATE));
+}
+
+static int bcm63xx_pcmcia_set_io_map(struct pcmcia_socket *sock,
+				     struct pccard_io_map *map)
+{
+	/* this doesn't seem to be called by pcmcia layer if static
+	 * mapping is used */
+	return 0;
+}
+
+static int bcm63xx_pcmcia_set_mem_map(struct pcmcia_socket *sock,
+				      struct pccard_mem_map *map)
+{
+	struct bcm63xx_pcmcia_socket *skt;
+	struct resource *res;
+
+	skt = sock->driver_data;
+	if (map->flags & MAP_ATTRIB)
+		res = skt->attr_res;
+	else
+		res = skt->common_res;
+
+	map->static_start = res->start + map->card_start;
+	return 0;
+}
+
+static struct pccard_operations bcm63xx_pcmcia_operations = {
+	.init			= bcm63xx_pcmcia_sock_init,
+	.suspend		= bcm63xx_pcmcia_suspend,
+	.get_status		= bcm63xx_pcmcia_get_status,
+	.set_socket		= bcm63xx_pcmcia_set_socket,
+	.set_io_map		= bcm63xx_pcmcia_set_io_map,
+	.set_mem_map		= bcm63xx_pcmcia_set_mem_map,
+};
+
+/*
+ * register pcmcia socket to core
+ */
+static int __devinit bcm63xx_drv_pcmcia_probe(struct platform_device *pdev)
+{
+	struct bcm63xx_pcmcia_socket *skt;
+	struct pcmcia_socket *sock;
+	struct resource *res, *irq_res;
+	unsigned int regmem_size = 0, iomem_size = 0;
+	u32 val;
+	int ret;
+
+	skt = kzalloc(sizeof(*skt), GFP_KERNEL);
+	if (!skt)
+		return -ENOMEM;
+	spin_lock_init(&skt->lock);
+	sock = &skt->socket;
+	sock->driver_data = skt;
+
+	/* make sure we have all resources we need */
+	skt->common_res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
+	skt->attr_res = platform_get_resource(pdev, IORESOURCE_MEM, 2);
+	irq_res = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
+	skt->pd = pdev->dev.platform_data;
+	if (!skt->common_res || !skt->attr_res || !irq_res || !skt->pd) {
+		ret = -EINVAL;
+		goto err;
+	}
+
+	/* remap pcmcia registers */
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	regmem_size = resource_size(res);
+	if (!request_mem_region(res->start, regmem_size, "bcm63xx_pcmcia")) {
+		ret = -EINVAL;
+		goto err;
+	}
+	skt->reg_res = res;
+
+	skt->base = ioremap(res->start, regmem_size);
+	if (!skt->base) {
+		ret = -ENOMEM;
+		goto err;
+	}
+
+	/* remap io registers */
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 3);
+	iomem_size = resource_size(res);
+	skt->io_base = ioremap(res->start, iomem_size);
+	if (!skt->io_base) {
+		ret = -ENOMEM;
+		goto err;
+	}
+
+	/* resources are static */
+	sock->resource_ops = &pccard_static_ops;
+	sock->ops = &bcm63xx_pcmcia_operations;
+	sock->owner = THIS_MODULE;
+	sock->dev.parent = &pdev->dev;
+	sock->features = SS_CAP_STATIC_MAP | SS_CAP_PCCARD;
+	sock->io_offset = (unsigned long)skt->io_base;
+	sock->pci_irq = irq_res->start;
+
+#ifdef CONFIG_CARDBUS
+	sock->cb_dev = bcm63xx_cb_dev;
+	if (bcm63xx_cb_dev)
+		sock->features |= SS_CAP_CARDBUS;
+#endif
+
+	/* assume common & attribute memory have the same size */
+	sock->map_size = resource_size(skt->common_res);
+
+	/* initialize polling timer */
+	setup_timer(&skt->timer, bcm63xx_pcmcia_poll, (unsigned long)skt);
+
+	/* initialize  pcmcia  control register,  drive  VS[12] to  0,
+	 * leave CB IDSEL to the old  value since it is set by the PCI
+	 * layer */
+	val = pcmcia_readl(skt, PCMCIA_C1_REG);
+	val &= PCMCIA_C1_CBIDSEL_MASK;
+	val |= PCMCIA_C1_EN_PCMCIA_GPIO_MASK;
+	pcmcia_writel(skt, val, PCMCIA_C1_REG);
+
+	/*
+	 * Hardware has only one set of timings registers, not one for
+	 * each memory access type, so we configure them for the
+	 * slowest one: attribute memory.
+	 */
+	val = PCMCIA_C2_DATA16_MASK;
+	val |= 10 << PCMCIA_C2_RWCOUNT_SHIFT;
+	val |= 6 << PCMCIA_C2_INACTIVE_SHIFT;
+	val |= 3 << PCMCIA_C2_SETUP_SHIFT;
+	val |= 3 << PCMCIA_C2_HOLD_SHIFT;
+	pcmcia_writel(skt, val, PCMCIA_C2_REG);
+
+	ret = pcmcia_register_socket(sock);
+	if (ret)
+		goto err;
+
+	/* start polling socket */
+	mod_timer(&skt->timer,
+		  jiffies + msecs_to_jiffies(BCM63XX_PCMCIA_POLL_RATE));
+
+	platform_set_drvdata(pdev, skt);
+	return 0;
+
+err:
+	if (skt->io_base)
+		iounmap(skt->io_base);
+	if (skt->base)
+		iounmap(skt->base);
+	if (skt->reg_res)
+		release_mem_region(skt->reg_res->start, regmem_size);
+	kfree(skt);
+	return ret;
+}
+
+static int __devexit bcm63xx_drv_pcmcia_remove(struct platform_device *pdev)
+{
+	struct bcm63xx_pcmcia_socket *skt;
+	struct resource *res;
+
+	skt = platform_get_drvdata(pdev);
+	del_timer_sync(&skt->timer);
+	iounmap(skt->base);
+	iounmap(skt->io_base);
+	res = skt->reg_res;
+	release_mem_region(res->start, resource_size(res));
+	kfree(skt);
+	return 0;
+}
+
+struct platform_driver bcm63xx_pcmcia_driver = {
+	.probe	= bcm63xx_drv_pcmcia_probe,
+	.remove	= __devexit_p(bcm63xx_drv_pcmcia_remove),
+	.driver	= {
+		.name	= "bcm63xx_pcmcia",
+		.owner  = THIS_MODULE,
+	},
+};
+
+#ifdef CONFIG_CARDBUS
+static int __devinit bcm63xx_cb_probe(struct pci_dev *dev,
+				      const struct pci_device_id *id)
+{
+	/* keep pci device */
+	bcm63xx_cb_dev = dev;
+	return platform_driver_register(&bcm63xx_pcmcia_driver);
+}
+
+static void __devexit bcm63xx_cb_exit(struct pci_dev *dev)
+{
+	platform_driver_unregister(&bcm63xx_pcmcia_driver);
+	bcm63xx_cb_dev = NULL;
+}
+
+static struct pci_device_id bcm63xx_cb_table[] = {
+	{
+		.vendor		= PCI_VENDOR_ID_BROADCOM,
+		.device		= BCM6348_CPU_ID,
+		.subvendor	= PCI_VENDOR_ID_BROADCOM,
+		.subdevice	= PCI_ANY_ID,
+		.class		= PCI_CLASS_BRIDGE_CARDBUS << 8,
+		.class_mask	= ~0,
+	},
+
+	{
+		.vendor		= PCI_VENDOR_ID_BROADCOM,
+		.device		= BCM6358_CPU_ID,
+		.subvendor	= PCI_VENDOR_ID_BROADCOM,
+		.subdevice	= PCI_ANY_ID,
+		.class		= PCI_CLASS_BRIDGE_CARDBUS << 8,
+		.class_mask	= ~0,
+	},
+
+	{ },
+};
+
+MODULE_DEVICE_TABLE(pci, bcm63xx_cb_table);
+
+static struct pci_driver bcm63xx_cardbus_driver = {
+	.name		= "bcm63xx_cardbus",
+	.id_table	= bcm63xx_cb_table,
+	.probe		= bcm63xx_cb_probe,
+	.remove		= __devexit_p(bcm63xx_cb_exit),
+};
+#endif
+
+/*
+ * if cardbus support is enabled, register our platform device after
+ * our fake cardbus bridge has been registered
+ */
+static int __init bcm63xx_pcmcia_init(void)
+{
+#ifdef CONFIG_CARDBUS
+	return pci_register_driver(&bcm63xx_cardbus_driver);
+#else
+	return platform_driver_register(&bcm63xx_pcmcia_driver);
+#endif
+}
+
+static void __exit bcm63xx_pcmcia_exit(void)
+{
+#ifdef CONFIG_CARDBUS
+	return pci_unregister_driver(&bcm63xx_cardbus_driver);
+#else
+	platform_driver_unregister(&bcm63xx_pcmcia_driver);
+#endif
+}
+
+module_init(bcm63xx_pcmcia_init);
+module_exit(bcm63xx_pcmcia_exit);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Maxime Bizon <mbizon@freebox.fr>");
+MODULE_DESCRIPTION("Linux PCMCIA Card Services: bcm63xx Socket Controller");

drivers/pcmcia/bcm63xx_pcmcia.h

+#ifndef BCM63XX_PCMCIA_H_
+#define BCM63XX_PCMCIA_H_
+
+#include <linux/types.h>
+#include <linux/timer.h>
+#include <pcmcia/ss.h>
+#include <bcm63xx_dev_pcmcia.h>
+
+/* socket polling rate in ms */
+#define BCM63XX_PCMCIA_POLL_RATE	500
+
+enum {
+	CARD_CARDBUS = (1 << 0),
+	CARD_PCCARD = (1 << 1),
+	CARD_5V = (1 << 2),
+	CARD_3V = (1 << 3),
+	CARD_XV = (1 << 4),
+	CARD_YV = (1 << 5),
+};
+
+struct bcm63xx_pcmcia_socket {
+	struct pcmcia_socket socket;
+
+	/* platform specific data */
+	struct bcm63xx_pcmcia_platform_data *pd;
+
+	/* all regs access are protected by this spinlock */
+	spinlock_t lock;
+
+	/* pcmcia registers resource */
+	struct resource *reg_res;
+
+	/* base remapped address of registers */
+	void __iomem *base;
+
+	/* whether a card is detected at the moment */
+	int card_detected;
+
+	/* type of detected card (mask of above enum) */
+	u8 card_type;
+
+	/* keep last socket status to implement event reporting */
+	unsigned int old_status;
+
+	/* backup of requested socket state */
+	socket_state_t requested_state;
+
+	/* timer used for socket status polling */
+	struct timer_list timer;
+
+	/* attribute/common memory resources */
+	struct resource *attr_res;
+	struct resource *common_res;
+	struct resource *io_res;
+
+	/* base address of io memory */
+	void __iomem *io_base;
+};
+
+#endif /* BCM63XX_PCMCIA_H_ */

drivers/serial/Kconfig

@@ -1458,4 +1458,23 @@ config SERIAL_TIMBERDALE
 	---help---
 	Add support for UART controller on timberdale.
 
+config SERIAL_BCM63XX
+	tristate "bcm63xx serial port support"
+	select SERIAL_CORE
+	depends on BCM63XX
+	help
+	  If you have a bcm63xx CPU, you can enable its onboard
+	  serial port by enabling this options.
+
+          To compile this driver as a module, choose M here: the
+          module will be called bcm963xx_uart.
+
+config SERIAL_BCM63XX_CONSOLE
+	bool "Console on bcm63xx serial port"
+	depends on SERIAL_BCM63XX=y
+	select SERIAL_CORE_CONSOLE
+	help
+	  If you have enabled the serial port on the bcm63xx CPU
+	  you can make it the console by answering Y to this option.
+
 endmenu

drivers/serial/Makefile

@@ -34,6 +34,7 @@ obj-$(CONFIG_SERIAL_CLPS711X) += clps711x.o
 obj-$(CONFIG_SERIAL_PXA) += pxa.o
 obj-$(CONFIG_SERIAL_PNX8XXX) += pnx8xxx_uart.o
 obj-$(CONFIG_SERIAL_SA1100) += sa1100.o
+obj-$(CONFIG_SERIAL_BCM63XX) += bcm63xx_uart.o
 obj-$(CONFIG_SERIAL_BFIN) += bfin_5xx.o
 obj-$(CONFIG_SERIAL_BFIN_SPORT) += bfin_sport_uart.o
 obj-$(CONFIG_SERIAL_SAMSUNG) += samsung.o

drivers/serial/bcm63xx_uart.c

+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Derived from many drivers using generic_serial interface.
+ *
+ * Copyright (C) 2008 Maxime Bizon <mbizon@freebox.fr>
+ *
+ *  Serial driver for BCM63xx integrated UART.
+ *
+ * Hardware flow control was _not_ tested since I only have RX/TX on
+ * my board.
+ */
+
+#if defined(CONFIG_SERIAL_BCM63XX_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
+#define SUPPORT_SYSRQ
+#endif
+
+#include <linux/kernel.h>
+#include <linux/platform_device.h>
+#include <linux/init.h>
+#include <linux/delay.h>
+#include <linux/module.h>
+#include <linux/console.h>
+#include <linux/clk.h>
+#include <linux/tty.h>
+#include <linux/tty_flip.h>
+#include <linux/sysrq.h>
+#include <linux/serial.h>
+#include <linux/serial_core.h>
+
+#include <bcm63xx_clk.h>
+#include <bcm63xx_irq.h>
+#include <bcm63xx_regs.h>
+#include <bcm63xx_io.h>
+
+#define BCM63XX_NR_UARTS	1
+
+static struct uart_port ports[BCM63XX_NR_UARTS];
+
+/*
+ * rx interrupt mask / stat
+ *
+ * mask:
+ *  - rx fifo full
+ *  - rx fifo above threshold
+ *  - rx fifo not empty for too long
+ */
+#define UART_RX_INT_MASK	(UART_IR_MASK(UART_IR_RXOVER) |		\
+				UART_IR_MASK(UART_IR_RXTHRESH) |	\
+				UART_IR_MASK(UART_IR_RXTIMEOUT))
+
+#define UART_RX_INT_STAT	(UART_IR_STAT(UART_IR_RXOVER) |		\
+				UART_IR_STAT(UART_IR_RXTHRESH) |	\
+				UART_IR_STAT(UART_IR_RXTIMEOUT))
+
+/*
+ * tx interrupt mask / stat
+ *
+ * mask:
+ * - tx fifo empty
+ * - tx fifo below threshold
+ */
+#define UART_TX_INT_MASK	(UART_IR_MASK(UART_IR_TXEMPTY) |	\
+				UART_IR_MASK(UART_IR_TXTRESH))
+
+#define UART_TX_INT_STAT	(UART_IR_STAT(UART_IR_TXEMPTY) |	\
+				UART_IR_STAT(UART_IR_TXTRESH))
+
+/*
+ * external input interrupt
+ *
+ * mask: any edge on CTS, DCD
+ */
+#define UART_EXTINP_INT_MASK	(UART_EXTINP_IRMASK(UART_EXTINP_IR_CTS) | \
+				 UART_EXTINP_IRMASK(UART_EXTINP_IR_DCD))
+
+/*
+ * handy uart register accessor
+ */
+static inline unsigned int bcm_uart_readl(struct uart_port *port,
+					 unsigned int offset)
+{
+	return bcm_readl(port->membase + offset);
+}
+
+static inline void bcm_uart_writel(struct uart_port *port,
+				  unsigned int value, unsigned int offset)
+{
+	bcm_writel(value, port->membase + offset);
+}
+
+/*
+ * serial core request to check if uart tx fifo is empty
+ */
+static unsigned int bcm_uart_tx_empty(struct uart_port *port)
+{
+	unsigned int val;
+
+	val = bcm_uart_readl(port, UART_IR_REG);
+	return (val & UART_IR_STAT(UART_IR_TXEMPTY)) ? 1 : 0;
+}
+
+/*
+ * serial core request to set RTS and DTR pin state and loopback mode
+ */
+static void bcm_uart_set_mctrl(struct uart_port *port, unsigned int mctrl)
+{
+	unsigned int val;
+
+	val = bcm_uart_readl(port, UART_MCTL_REG);
+	val &= ~(UART_MCTL_DTR_MASK | UART_MCTL_RTS_MASK);
+	/* invert of written value is reflected on the pin */
+	if (!(mctrl & TIOCM_DTR))
+		val |= UART_MCTL_DTR_MASK;
+	if (!(mctrl & TIOCM_RTS))
+		val |= UART_MCTL_RTS_MASK;
+	bcm_uart_writel(port, val, UART_MCTL_REG);
+
+	val = bcm_uart_readl(port, UART_CTL_REG);
+	if (mctrl & TIOCM_LOOP)
+		val |= UART_CTL_LOOPBACK_MASK;
+	else
+		val &= ~UART_CTL_LOOPBACK_MASK;
+	bcm_uart_writel(port, val, UART_CTL_REG);
+}
+
+/*
+ * serial core request to return RI, CTS, DCD and DSR pin state
+ */
+static unsigned int bcm_uart_get_mctrl(struct uart_port *port)
+{
+	unsigned int val, mctrl;
+
+	mctrl = 0;
+	val = bcm_uart_readl(port, UART_EXTINP_REG);
+	if (val & UART_EXTINP_RI_MASK)
+		mctrl |= TIOCM_RI;
+	if (val & UART_EXTINP_CTS_MASK)
+		mctrl |= TIOCM_CTS;
+	if (val & UART_EXTINP_DCD_MASK)
+		mctrl |= TIOCM_CD;
+	if (val & UART_EXTINP_DSR_MASK)
+		mctrl |= TIOCM_DSR;
+	return mctrl;
+}
+
+/*
+ * serial core request to disable tx ASAP (used for flow control)
+ */
+static void bcm_uart_stop_tx(struct uart_port *port)
+{
+	unsigned int val;
+
+	val = bcm_uart_readl(port, UART_CTL_REG);
+	val &= ~(UART_CTL_TXEN_MASK);
+	bcm_uart_writel(port, val, UART_CTL_REG);
+
+	val = bcm_uart_readl(port, UART_IR_REG);
+	val &= ~UART_TX_INT_MASK;
+	bcm_uart_writel(port, val, UART_IR_REG);
+}
+
+/*
+ * serial core request to (re)enable tx
+ */
+static void bcm_uart_start_tx(struct uart_port *port)
+{
+	unsigned int val;
+
+	val = bcm_uart_readl(port, UART_IR_REG);
+	val |= UART_TX_INT_MASK;
+	bcm_uart_writel(port, val, UART_IR_REG);
+
+	val = bcm_uart_readl(port, UART_CTL_REG);
+	val |= UART_CTL_TXEN_MASK;
+	bcm_uart_writel(port, val, UART_CTL_REG);
+}
+
+/*
+ * serial core request to stop rx, called before port shutdown
+ */
+static void bcm_uart_stop_rx(struct uart_port *port)
+{
+	unsigned int val;
+
+	val = bcm_uart_readl(port, UART_IR_REG);
+	val &= ~UART_RX_INT_MASK;
+	bcm_uart_writel(port, val, UART_IR_REG);
+}
+
+/*
+ * serial core request to enable modem status interrupt reporting
+ */
+static void bcm_uart_enable_ms(struct uart_port *port)
+{
+	unsigned int val;
+
+	val = bcm_uart_readl(port, UART_IR_REG);
+	val |= UART_IR_MASK(UART_IR_EXTIP);
+	bcm_uart_writel(port, val, UART_IR_REG);
+}
+
+/*
+ * serial core request to start/stop emitting break char
+ */
+static void bcm_uart_break_ctl(struct uart_port *port, int ctl)
+{
+	unsigned long flags;
+	unsigned int val;
+
+	spin_lock_irqsave(&port->lock, flags);
+
+	val = bcm_uart_readl(port, UART_CTL_REG);
+	if (ctl)
+		val |= UART_CTL_XMITBRK_MASK;
+	else
+		val &= ~UART_CTL_XMITBRK_MASK;
+	bcm_uart_writel(port, val, UART_CTL_REG);
+
+	spin_unlock_irqrestore(&port->lock, flags);
+}
+
+/*
+ * return port type in string format
+ */
+static const char *bcm_uart_type(struct uart_port *port)
+{
+	return (port->type == PORT_BCM63XX) ? "bcm63xx_uart" : NULL;
+}
+
+/*
+ * read all chars in rx fifo and send them to core
+ */
+static void bcm_uart_do_rx(struct uart_port *port)
+{
+	struct tty_struct *tty;
+	unsigned int max_count;
+
+	/* limit number of char read in interrupt, should not be
+	 * higher than fifo size anyway since we're much faster than
+	 * serial port */
+	max_count = 32;
+	tty = port->info->port.tty;
+	do {
+		unsigned int iestat, c, cstat;
+		char flag;
+
+		/* get overrun/fifo empty information from ier
+		 * register */
+		iestat = bcm_uart_readl(port, UART_IR_REG);
+		if (!(iestat & UART_IR_STAT(UART_IR_RXNOTEMPTY)))
+			break;
+
+		cstat = c = bcm_uart_readl(port, UART_FIFO_REG);
+		port->icount.rx++;
+		flag = TTY_NORMAL;
+		c &= 0xff;
+
+		if (unlikely((cstat & UART_FIFO_ANYERR_MASK))) {
+			/* do stats first */
+			if (cstat & UART_FIFO_BRKDET_MASK) {
+				port->icount.brk++;
+				if (uart_handle_break(port))
+					continue;
+			}
+
+			if (cstat & UART_FIFO_PARERR_MASK)
+				port->icount.parity++;
+			if (cstat & UART_FIFO_FRAMEERR_MASK)
+				port->icount.frame++;
+
+			/* update flag wrt read_status_mask */
+			cstat &= port->read_status_mask;
+			if (cstat & UART_FIFO_BRKDET_MASK)
+				flag = TTY_BREAK;
+			if (cstat & UART_FIFO_FRAMEERR_MASK)
+				flag = TTY_FRAME;
+			if (cstat & UART_FIFO_PARERR_MASK)
+				flag = TTY_PARITY;
+		}
+
+		if (uart_handle_sysrq_char(port, c))
+			continue;
+
+		if (unlikely(iestat & UART_IR_STAT(UART_IR_RXOVER))) {
+			port->icount.overrun++;
+			tty_insert_flip_char(tty, 0, TTY_OVERRUN);
+		}
+
+		if ((cstat & port->ignore_status_mask) == 0)
+			tty_insert_flip_char(tty, c, flag);
+
+	} while (--max_count);
+
+	tty_flip_buffer_push(tty);
+}
+
+/*
+ * fill tx fifo with chars to send, stop when fifo is about to be full
+ * or when all chars have been sent.
+ */
+static void bcm_uart_do_tx(struct uart_port *port)
+{
+	struct circ_buf *xmit;
+	unsigned int val, max_count;
+
+	if (port->x_char) {
+		bcm_uart_writel(port, port->x_char, UART_FIFO_REG);
+		port->icount.tx++;
+		port->x_char = 0;
+		return;
+	}
+
+	if (uart_tx_stopped(port)) {
+		bcm_uart_stop_tx(port);
+		return;
+	}
+
+	xmit = &port->info->xmit;
+	if (uart_circ_empty(xmit))
+		goto txq_empty;
+
+	val = bcm_uart_readl(port, UART_MCTL_REG);
+	val = (val & UART_MCTL_TXFIFOFILL_MASK) >> UART_MCTL_TXFIFOFILL_SHIFT;
+	max_count = port->fifosize - val;
+
+	while (max_count--) {
+		unsigned int c;
+
+		c = xmit->buf[xmit->tail];
+		bcm_uart_writel(port, c, UART_FIFO_REG);
+		xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
+		port->icount.tx++;
+		if (uart_circ_empty(xmit))
+			break;
+	}
+
+	if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
+		uart_write_wakeup(port);
+
+	if (uart_circ_empty(xmit))
+		goto txq_empty;
+	return;
+
+txq_empty:
+	/* nothing to send, disable transmit interrupt */
+	val = bcm_uart_readl(port, UART_IR_REG);
+	val &= ~UART_TX_INT_MASK;
+	bcm_uart_writel(port, val, UART_IR_REG);
+	return;
+}
+
+/*
+ * process uart interrupt
+ */
+static irqreturn_t bcm_uart_interrupt(int irq, void *dev_id)
+{
+	struct uart_port *port;
+	unsigned int irqstat;
+
+	port = dev_id;
+	spin_lock(&port->lock);
+
+	irqstat = bcm_uart_readl(port, UART_IR_REG);
+	if (irqstat & UART_RX_INT_STAT)
+		bcm_uart_do_rx(port);
+
+	if (irqstat & UART_TX_INT_STAT)
+		bcm_uart_do_tx(port);
+
+	if (irqstat & UART_IR_MASK(UART_IR_EXTIP)) {
+		unsigned int estat;
+
+		estat = bcm_uart_readl(port, UART_EXTINP_REG);
+		if (estat & UART_EXTINP_IRSTAT(UART_EXTINP_IR_CTS))
+			uart_handle_cts_change(port,
+					       estat & UART_EXTINP_CTS_MASK);
+		if (estat & UART_EXTINP_IRSTAT(UART_EXTINP_IR_DCD))
+			uart_handle_dcd_change(port,
+					       estat & UART_EXTINP_DCD_MASK);
+	}
+
+	spin_unlock(&port->lock);
+	return IRQ_HANDLED;
+}
+
+/*
+ * enable rx & tx operation on uart
+ */
+static void bcm_uart_enable(struct uart_port *port)
+{
+	unsigned int val;
+
+	val = bcm_uart_readl(port, UART_CTL_REG);
+	val |= (UART_CTL_BRGEN_MASK | UART_CTL_TXEN_MASK | UART_CTL_RXEN_MASK);
+	bcm_uart_writel(port, val, UART_CTL_REG);
+}
+
+/*
+ * disable rx & tx operation on uart
+ */
+static void bcm_uart_disable(struct uart_port *port)
+{
+	unsigned int val;
+
+	val = bcm_uart_readl(port, UART_CTL_REG);
+	val &= ~(UART_CTL_BRGEN_MASK | UART_CTL_TXEN_MASK |
+		 UART_CTL_RXEN_MASK);
+	bcm_uart_writel(port, val, UART_CTL_REG);
+}
+
+/*
+ * clear all unread data in rx fifo and unsent data in tx fifo
+ */
+static void bcm_uart_flush(struct uart_port *port)
+{
+	unsigned int val;
+
+	/* empty rx and tx fifo */
+	val = bcm_uart_readl(port, UART_CTL_REG);
+	val |= UART_CTL_RSTRXFIFO_MASK | UART_CTL_RSTTXFIFO_MASK;
+	bcm_uart_writel(port, val, UART_CTL_REG);
+
+	/* read any pending char to make sure all irq status are
+	 * cleared */
+	(void)bcm_uart_readl(port, UART_FIFO_REG);
+}
+
+/*
+ * serial core request to initialize uart and start rx operation
+ */
+static int bcm_uart_startup(struct uart_port *port)
+{
+	unsigned int val;
+	int ret;
+
+	/* mask all irq and flush port */
+	bcm_uart_disable(port);
+	bcm_uart_writel(port, 0, UART_IR_REG);
+	bcm_uart_flush(port);
+
+	/* clear any pending external input interrupt */
+	(void)bcm_uart_readl(port, UART_EXTINP_REG);
+
+	/* set rx/tx fifo thresh to fifo half size */
+	val = bcm_uart_readl(port, UART_MCTL_REG);
+	val &= ~(UART_MCTL_RXFIFOTHRESH_MASK | UART_MCTL_TXFIFOTHRESH_MASK);
+	val |= (port->fifosize / 2) << UART_MCTL_RXFIFOTHRESH_SHIFT;
+	val |= (port->fifosize / 2) << UART_MCTL_TXFIFOTHRESH_SHIFT;
+	bcm_uart_writel(port, val, UART_MCTL_REG);
+
+	/* set rx fifo timeout to 1 char time */
+	val = bcm_uart_readl(port, UART_CTL_REG);
+	val &= ~UART_CTL_RXTMOUTCNT_MASK;
+	val |= 1 << UART_CTL_RXTMOUTCNT_SHIFT;
+	bcm_uart_writel(port, val, UART_CTL_REG);
+
+	/* report any edge on dcd and cts */
+	val = UART_EXTINP_INT_MASK;
+	val |= UART_EXTINP_DCD_NOSENSE_MASK;
+	val |= UART_EXTINP_CTS_NOSENSE_MASK;
+	bcm_uart_writel(port, val, UART_EXTINP_REG);
+
+	/* register irq and enable rx interrupts */
+	ret = request_irq(port->irq, bcm_uart_interrupt, 0,
+			  bcm_uart_type(port), port);
+	if (ret)
+		return ret;
+	bcm_uart_writel(port, UART_RX_INT_MASK, UART_IR_REG);
+	bcm_uart_enable(port);
+	return 0;
+}
+
+/*
+ * serial core request to flush & disable uart
+ */
+static void bcm_uart_shutdown(struct uart_port *port)
+{
+	unsigned long flags;
+
+	spin_lock_irqsave(&port->lock, flags);
+	bcm_uart_writel(port, 0, UART_IR_REG);
+	spin_unlock_irqrestore(&port->lock, flags);
+
+	bcm_uart_disable(port);
+	bcm_uart_flush(port);
+	free_irq(port->irq, port);
+}
+
+/*
+ * serial core request to change current uart setting
+ */
+static void bcm_uart_set_termios(struct uart_port *port,
+				 struct ktermios *new,
+				 struct ktermios *old)
+{
+	unsigned int ctl, baud, quot, ier;
+	unsigned long flags;
+
+	spin_lock_irqsave(&port->lock, flags);
+
+	/* disable uart while changing speed */
+	bcm_uart_disable(port);
+	bcm_uart_flush(port);
+
+	/* update Control register */
+	ctl = bcm_uart_readl(port, UART_CTL_REG);
+	ctl &= ~UART_CTL_BITSPERSYM_MASK;
+
+	switch (new->c_cflag & CSIZE) {
+	case CS5:
+		ctl |= (0 << UART_CTL_BITSPERSYM_SHIFT);
+		break;
+	case CS6:
+		ctl |= (1 << UART_CTL_BITSPERSYM_SHIFT);
+		break;
+	case CS7:
+		ctl |= (2 << UART_CTL_BITSPERSYM_SHIFT);
+		break;
+	default:
+		ctl |= (3 << UART_CTL_BITSPERSYM_SHIFT);
+		break;
+	}
+
+	ctl &= ~UART_CTL_STOPBITS_MASK;
+	if (new->c_cflag & CSTOPB)
+		ctl |= UART_CTL_STOPBITS_2;
+	else
+		ctl |= UART_CTL_STOPBITS_1;
+
+	ctl &= ~(UART_CTL_RXPAREN_MASK | UART_CTL_TXPAREN_MASK);
+	if (new->c_cflag & PARENB)
+		ctl |= (UART_CTL_RXPAREN_MASK | UART_CTL_TXPAREN_MASK);
+	ctl &= ~(UART_CTL_RXPAREVEN_MASK | UART_CTL_TXPAREVEN_MASK);
+	if (new->c_cflag & PARODD)
+		ctl |= (UART_CTL_RXPAREVEN_MASK | UART_CTL_TXPAREVEN_MASK);
+	bcm_uart_writel(port, ctl, UART_CTL_REG);
+
+	/* update Baudword register */
+	baud = uart_get_baud_rate(port, new, old, 0, port->uartclk / 16);
+	quot = uart_get_divisor(port, baud) - 1;
+	bcm_uart_writel(port, quot, UART_BAUD_REG);
+
+	/* update Interrupt register */
+	ier = bcm_uart_readl(port, UART_IR_REG);
+
+	ier &= ~UART_IR_MASK(UART_IR_EXTIP);
+	if (UART_ENABLE_MS(port, new->c_cflag))
+		ier |= UART_IR_MASK(UART_IR_EXTIP);
+
+	bcm_uart_writel(port, ier, UART_IR_REG);
+
+	/* update read/ignore mask */
+	port->read_status_mask = UART_FIFO_VALID_MASK;
+	if (new->c_iflag & INPCK) {
+		port->read_status_mask |= UART_FIFO_FRAMEERR_MASK;
+		port->read_status_mask |= UART_FIFO_PARERR_MASK;
+	}
+	if (new->c_iflag & (BRKINT))
+		port->read_status_mask |= UART_FIFO_BRKDET_MASK;
+
+	port->ignore_status_mask = 0;
+	if (new->c_iflag & IGNPAR)
+		port->ignore_status_mask |= UART_FIFO_PARERR_MASK;
+	if (new->c_iflag & IGNBRK)
+		port->ignore_status_mask |= UART_FIFO_BRKDET_MASK;
+	if (!(new->c_cflag & CREAD))
+		port->ignore_status_mask |= UART_FIFO_VALID_MASK;
+
+	uart_update_timeout(port, new->c_cflag, baud);
+	bcm_uart_enable(port);
+	spin_unlock_irqrestore(&port->lock, flags);
+}
+
+/*
+ * serial core request to claim uart iomem
+ */
+static int bcm_uart_request_port(struct uart_port *port)
+{
+	unsigned int size;
+
+	size = RSET_UART_SIZE;
+	if (!request_mem_region(port->mapbase, size, "bcm63xx")) {
+		dev_err(port->dev, "Memory region busy\n");
+		return -EBUSY;
+	}
+
+	port->membase = ioremap(port->mapbase, size);
+	if (!port->membase) {
+		dev_err(port->dev, "Unable to map registers\n");
+		release_mem_region(port->mapbase, size);
+		return -EBUSY;
+	}
+	return 0;
+}
+
+/*
+ * serial core request to release uart iomem
+ */
+static void bcm_uart_release_port(struct uart_port *port)
+{
+	release_mem_region(port->mapbase, RSET_UART_SIZE);
+	iounmap(port->membase);
+}
+
+/*
+ * serial core request to do any port required autoconfiguration
+ */
+static void bcm_uart_config_port(struct uart_port *port, int flags)
+{
+	if (flags & UART_CONFIG_TYPE) {
+		if (bcm_uart_request_port(port))
+			return;
+		port->type = PORT_BCM63XX;
+	}
+}
+
+/*
+ * serial core request to check that port information in serinfo are
+ * suitable
+ */
+static int bcm_uart_verify_port(struct uart_port *port,
+				struct serial_struct *serinfo)
+{
+	if (port->type != PORT_BCM63XX)
+		return -EINVAL;
+	if (port->irq != serinfo->irq)
+		return -EINVAL;
+	if (port->iotype != serinfo->io_type)
+		return -EINVAL;
+	if (port->mapbase != (unsigned long)serinfo->iomem_base)
+		return -EINVAL;
+	return 0;
+}
+
+/* serial core callbacks */
+static struct uart_ops bcm_uart_ops = {
+	.tx_empty	= bcm_uart_tx_empty,
+	.get_mctrl	= bcm_uart_get_mctrl,
+	.set_mctrl	= bcm_uart_set_mctrl,
+	.start_tx	= bcm_uart_start_tx,
+	.stop_tx	= bcm_uart_stop_tx,
+	.stop_rx	= bcm_uart_stop_rx,
+	.enable_ms	= bcm_uart_enable_ms,
+	.break_ctl	= bcm_uart_break_ctl,
+	.startup	= bcm_uart_startup,
+	.shutdown	= bcm_uart_shutdown,
+	.set_termios	= bcm_uart_set_termios,
+	.type		= bcm_uart_type,
+	.release_port	= bcm_uart_release_port,
+	.request_port	= bcm_uart_request_port,
+	.config_port	= bcm_uart_config_port,
+	.verify_port	= bcm_uart_verify_port,
+};
+
+
+
+#ifdef CONFIG_SERIAL_BCM63XX_CONSOLE
+static inline void wait_for_xmitr(struct uart_port *port)
+{
+	unsigned int tmout;
+
+	/* Wait up to 10ms for the character(s) to be sent. */
+	tmout = 10000;
+	while (--tmout) {
+		unsigned int val;
+
+		val = bcm_uart_readl(port, UART_IR_REG);
+		if (val & UART_IR_STAT(UART_IR_TXEMPTY))
+			break;
+		udelay(1);
+	}
+
+	/* Wait up to 1s for flow control if necessary */
+	if (port->flags & UPF_CONS_FLOW) {
+		tmout = 1000000;
+		while (--tmout) {
+			unsigned int val;
+
+			val = bcm_uart_readl(port, UART_EXTINP_REG);
+			if (val & UART_EXTINP_CTS_MASK)
+				break;
+			udelay(1);
+		}
+	}
+}
+
+/*
+ * output given char
+ */
+static void bcm_console_putchar(struct uart_port *port, int ch)
+{
+	wait_for_xmitr(port);
+	bcm_uart_writel(port, ch, UART_FIFO_REG);
+}
+
+/*
+ * console core request to output given string
+ */
+static void bcm_console_write(struct console *co, const char *s,
+			      unsigned int count)
+{
+	struct uart_port *port;
+	unsigned long flags;
+	int locked;
+
+	port = &ports[co->index];
+
+	local_irq_save(flags);
+	if (port->sysrq) {
+		/* bcm_uart_interrupt() already took the lock */
+		locked = 0;
+	} else if (oops_in_progress) {
+		locked = spin_trylock(&port->lock);
+	} else {
+		spin_lock(&port->lock);
+		locked = 1;
+	}
+
+	/* call helper to deal with \r\n */
+	uart_console_write(port, s, count, bcm_console_putchar);
+
+	/* and wait for char to be transmitted */
+	wait_for_xmitr(port);
+
+	if (locked)
+		spin_unlock(&port->lock);
+	local_irq_restore(flags);
+}
+
+/*
+ * console core request to setup given console, find matching uart
+ * port and setup it.
+ */
+static int bcm_console_setup(struct console *co, char *options)
+{
+	struct uart_port *port;
+	int baud = 9600;
+	int bits = 8;
+	int parity = 'n';
+	int flow = 'n';
+
+	if (co->index < 0 || co->index >= BCM63XX_NR_UARTS)
+		return -EINVAL;
+	port = &ports[co->index];
+	if (!port->membase)
+		return -ENODEV;
+	if (options)
+		uart_parse_options(options, &baud, &parity, &bits, &flow);
+
+	return uart_set_options(port, co, baud, parity, bits, flow);
+}
+
+static struct uart_driver bcm_uart_driver;
+
+static struct console bcm63xx_console = {
+	.name		= "ttyS",
+	.write		= bcm_console_write,
+	.device		= uart_console_device,
+	.setup		= bcm_console_setup,
+	.flags		= CON_PRINTBUFFER,
+	.index		= -1,
+	.data		= &bcm_uart_driver,
+};
+
+static int __init bcm63xx_console_init(void)
+{
+	register_console(&bcm63xx_console);
+	return 0;
+}
+
+console_initcall(bcm63xx_console_init);
+
+#define BCM63XX_CONSOLE	(&bcm63xx_console)
+#else
+#define BCM63XX_CONSOLE	NULL
+#endif /* CONFIG_SERIAL_BCM63XX_CONSOLE */
+
+static struct uart_driver bcm_uart_driver = {
+	.owner		= THIS_MODULE,
+	.driver_name	= "bcm63xx_uart",
+	.dev_name	= "ttyS",
+	.major		= TTY_MAJOR,
+	.minor		= 64,
+	.nr		= 1,
+	.cons		= BCM63XX_CONSOLE,
+};
+
+/*
+ * platform driver probe/remove callback
+ */
+static int __devinit bcm_uart_probe(struct platform_device *pdev)
+{
+	struct resource *res_mem, *res_irq;
+	struct uart_port *port;
+	struct clk *clk;
+	int ret;
+
+	if (pdev->id < 0 || pdev->id >= BCM63XX_NR_UARTS)
+		return -EINVAL;
+
+	if (ports[pdev->id].membase)
+		return -EBUSY;
+
+	res_mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (!res_mem)
+		return -ENODEV;
+
+	res_irq = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
+	if (!res_irq)
+		return -ENODEV;
+
+	clk = clk_get(&pdev->dev, "periph");
+	if (IS_ERR(clk))
+		return -ENODEV;
+
+	port = &ports[pdev->id];
+	memset(port, 0, sizeof(*port));
+	port->iotype = UPIO_MEM;
+	port->mapbase = res_mem->start;
+	port->irq = res_irq->start;
+	port->ops = &bcm_uart_ops;
+	port->flags = UPF_BOOT_AUTOCONF;
+	port->dev = &pdev->dev;
+	port->fifosize = 16;
+	port->uartclk = clk_get_rate(clk) / 2;
+	clk_put(clk);
+
+	ret = uart_add_one_port(&bcm_uart_driver, port);
+	if (ret) {
+		kfree(port);
+		return ret;
+	}
+	platform_set_drvdata(pdev, port);
+	return 0;
+}
+
+static int __devexit bcm_uart_remove(struct platform_device *pdev)
+{
+	struct uart_port *port;
+
+	port = platform_get_drvdata(pdev);
+	uart_remove_one_port(&bcm_uart_driver, port);
+	platform_set_drvdata(pdev, NULL);
+	/* mark port as free */
+	ports[pdev->id].membase = 0;
+	return 0;
+}
+
+/*
+ * platform driver stuff
+ */
+static struct platform_driver bcm_uart_platform_driver = {
+	.probe	= bcm_uart_probe,
+	.remove	= __devexit_p(bcm_uart_remove),
+	.driver	= {
+		.owner = THIS_MODULE,
+		.name  = "bcm63xx_uart",
+	},
+};
+
+static int __init bcm_uart_init(void)
+{
+	int ret;
+
+	ret = uart_register_driver(&bcm_uart_driver);
+	if (ret)
+		return ret;
+
+	ret = platform_driver_register(&bcm_uart_platform_driver);
+	if (ret)
+		uart_unregister_driver(&bcm_uart_driver);
+
+	return ret;
+}
+
+static void __exit bcm_uart_exit(void)
+{
+	platform_driver_unregister(&bcm_uart_platform_driver);
+	uart_unregister_driver(&bcm_uart_driver);
+}
+
+module_init(bcm_uart_init);
+module_exit(bcm_uart_exit);
+
+MODULE_AUTHOR("Maxime Bizon <mbizon@freebox.fr>");
+MODULE_DESCRIPTION("Broadcom 63<xx integrated uart driver");
+MODULE_LICENSE("GPL");

include/linux/serial_core.h

@@ -176,6 +176,9 @@
 /* Qualcomm MSM SoCs */
 #define PORT_MSM	88
 
+/* BCM63xx family SoCs */
+#define PORT_BCM63XX	89
+
 #ifdef __KERNEL__
 
 #include <linux/compiler.h>