Merge branch 'upstream-davem' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6

arch/arm/mach-kirkwood/rd88f6281-setup.c

@@ -18,6 +18,7 @@
 #include <linux/timer.h>
 #include <linux/ata_platform.h>
 #include <linux/mv643xx_eth.h>
+#include <linux/ethtool.h>
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
 #include <asm/mach/pci.h>
@@ -69,6 +70,8 @@ static struct platform_device rd88f6281_nand_flash = {
 
 static struct mv643xx_eth_platform_data rd88f6281_ge00_data = {
 	.phy_addr	= -1,
+	.speed		= SPEED_1000,
+	.duplex		= DUPLEX_FULL,
 };
 
 static struct mv_sata_platform_data rd88f6281_sata_data = {

arch/arm/mach-orion5x/rd88f5181l-fxo-setup.c

@@ -15,6 +15,7 @@
 #include <linux/irq.h>
 #include <linux/mtd/physmap.h>
 #include <linux/mv643xx_eth.h>
+#include <linux/ethtool.h>
 #include <asm/mach-types.h>
 #include <asm/gpio.h>
 #include <asm/leds.h>
@@ -88,6 +89,8 @@ static struct orion5x_mpp_mode rd88f5181l_fxo_mpp_modes[] __initdata = {
 
 static struct mv643xx_eth_platform_data rd88f5181l_fxo_eth_data = {
 	.phy_addr	= -1,
+	.speed		= SPEED_1000,
+	.duplex		= DUPLEX_FULL,
 };
 
 static void __init rd88f5181l_fxo_init(void)

arch/arm/mach-orion5x/rd88f5181l-ge-setup.c

@@ -15,6 +15,7 @@
 #include <linux/irq.h>
 #include <linux/mtd/physmap.h>
 #include <linux/mv643xx_eth.h>
+#include <linux/ethtool.h>
 #include <linux/i2c.h>
 #include <asm/mach-types.h>
 #include <asm/gpio.h>
@@ -89,6 +90,8 @@ static struct orion5x_mpp_mode rd88f5181l_ge_mpp_modes[] __initdata = {
 
 static struct mv643xx_eth_platform_data rd88f5181l_ge_eth_data = {
 	.phy_addr	= -1,
+	.speed		= SPEED_1000,
+	.duplex		= DUPLEX_FULL,
 };
 
 static struct i2c_board_info __initdata rd88f5181l_ge_i2c_rtc = {

arch/arm/mach-orion5x/wnr854t-setup.c

@@ -14,6 +14,7 @@
 #include <linux/delay.h>
 #include <linux/mtd/physmap.h>
 #include <linux/mv643xx_eth.h>
+#include <linux/ethtool.h>
 #include <asm/mach-types.h>
 #include <asm/gpio.h>
 #include <asm/mach/arch.h>
@@ -92,6 +93,8 @@ static struct platform_device wnr854t_nor_flash = {
 
 static struct mv643xx_eth_platform_data wnr854t_eth_data = {
 	.phy_addr	= -1,
+	.speed		= SPEED_1000,
+	.duplex		= DUPLEX_FULL,
 };
 
 static void __init wnr854t_init(void)

arch/arm/mach-orion5x/wrt350n-v2-setup.c

@@ -14,6 +14,7 @@
 #include <linux/delay.h>
 #include <linux/mtd/physmap.h>
 #include <linux/mv643xx_eth.h>
+#include <linux/ethtool.h>
 #include <asm/mach-types.h>
 #include <asm/gpio.h>
 #include <asm/mach/arch.h>
@@ -100,6 +101,8 @@ static struct platform_device wrt350n_v2_nor_flash = {
 
 static struct mv643xx_eth_platform_data wrt350n_v2_eth_data = {
 	.phy_addr	= -1,
+	.speed		= SPEED_1000,
+	.duplex		= DUPLEX_FULL,
 };
 
 static void __init wrt350n_v2_init(void)

drivers/net/Kconfig

@@ -510,14 +510,14 @@ config STNIC
 config SH_ETH
 	tristate "Renesas SuperH Ethernet support"
 	depends on SUPERH && \
-		(CPU_SUBTYPE_SH7710 || CPU_SUBTYPE_SH7712)
+		(CPU_SUBTYPE_SH7710 || CPU_SUBTYPE_SH7712 || CPU_SUBTYPE_SH7763)
 	select CRC32
 	select MII
 	select MDIO_BITBANG
 	select PHYLIB
 	help
 	  Renesas SuperH Ethernet device driver.
-	  This driver support SH7710 and SH7712.
+	  This driver support SH7710, SH7712 and SH7763.
 
 config SUNLANCE
 	tristate "Sun LANCE support"

drivers/net/bfin_mac.c

@@ -605,36 +605,87 @@ static void adjust_tx_list(void)
 static int bfin_mac_hard_start_xmit(struct sk_buff *skb,
 				struct net_device *dev)
 {
-	unsigned int data;
+	u16 *data;
 
 	current_tx_ptr->skb = skb;
 
+	if (ANOMALY_05000285) {
 		/*
-	 * Is skb->data always 16-bit aligned?
-	 * Do we need to memcpy((char *)(tail->packet + 2), skb->data, len)?
+		 * TXDWA feature is not avaible to older revision < 0.3 silicon
+		 * of BF537
+		 *
+		 * Only if data buffer is ODD WORD alignment, we do not
+		 * need to memcpy
+		 */
+		u32 data_align = (u32)(skb->data) & 0x3;
+		if (data_align == 0x2) {
+			/* move skb->data to current_tx_ptr payload */
+			data = (u16 *)(skb->data) - 1;
+			*data = (u16)(skb->len);
+			current_tx_ptr->desc_a.start_addr = (u32)data;
+			/* this is important! */
+			blackfin_dcache_flush_range((u32)data,
+					(u32)((u8 *)data + skb->len + 4));
+		} else {
+			*((u16 *)(current_tx_ptr->packet)) = (u16)(skb->len);
+			memcpy((u8 *)(current_tx_ptr->packet + 2), skb->data,
+				skb->len);
+			current_tx_ptr->desc_a.start_addr =
+				(u32)current_tx_ptr->packet;
+			if (current_tx_ptr->status.status_word != 0)
+				current_tx_ptr->status.status_word = 0;
+			blackfin_dcache_flush_range(
+				(u32)current_tx_ptr->packet,
+				(u32)(current_tx_ptr->packet + skb->len + 2));
+		}
+	} else {
+		/*
+		 * TXDWA feature is avaible to revision < 0.3 silicon of
+		 * BF537 and always avaible to BF52x
 		 */
-	if ((((unsigned int)(skb->data)) & 0x02) == 2) {
+		u32 data_align = (u32)(skb->data) & 0x3;
+		if (data_align == 0x0) {
+			u16 sysctl = bfin_read_EMAC_SYSCTL();
+			sysctl |= TXDWA;
+			bfin_write_EMAC_SYSCTL(sysctl);
+
 			/* move skb->data to current_tx_ptr payload */
-		data = (unsigned int)(skb->data) - 2;
-		*((unsigned short *)data) = (unsigned short)(skb->len);
-		current_tx_ptr->desc_a.start_addr = (unsigned long)data;
+			data = (u16 *)(skb->data) - 2;
+			*data = (u16)(skb->len);
+			current_tx_ptr->desc_a.start_addr = (u32)data;
 			/* this is important! */
-		blackfin_dcache_flush_range(data, (data + (skb->len)) + 2);
+			blackfin_dcache_flush_range(
+					(u32)data,
+					(u32)((u8 *)data + skb->len + 4));
+		} else if (data_align == 0x2) {
+			u16 sysctl = bfin_read_EMAC_SYSCTL();
+			sysctl &= ~TXDWA;
+			bfin_write_EMAC_SYSCTL(sysctl);
 
+			/* move skb->data to current_tx_ptr payload */
+			data = (u16 *)(skb->data) - 1;
+			*data = (u16)(skb->len);
+			current_tx_ptr->desc_a.start_addr = (u32)data;
+			/* this is important! */
+			blackfin_dcache_flush_range(
+					(u32)data,
+					(u32)((u8 *)data + skb->len + 4));
 		} else {
-		*((unsigned short *)(current_tx_ptr->packet)) =
-		    (unsigned short)(skb->len);
-		memcpy((char *)(current_tx_ptr->packet + 2), skb->data,
-		       (skb->len));
+			u16 sysctl = bfin_read_EMAC_SYSCTL();
+			sysctl &= ~TXDWA;
+			bfin_write_EMAC_SYSCTL(sysctl);
+
+			*((u16 *)(current_tx_ptr->packet)) = (u16)(skb->len);
+			memcpy((u8 *)(current_tx_ptr->packet + 2), skb->data,
+				skb->len);
 			current_tx_ptr->desc_a.start_addr =
-		    (unsigned long)current_tx_ptr->packet;
+				(u32)current_tx_ptr->packet;
 			if (current_tx_ptr->status.status_word != 0)
 				current_tx_ptr->status.status_word = 0;
-		blackfin_dcache_flush_range((unsigned int)current_tx_ptr->
-					    packet,
-					    (unsigned int)(current_tx_ptr->
-							   packet + skb->len) +
-					    2);
+			blackfin_dcache_flush_range(
+				(u32)current_tx_ptr->packet,
+				(u32)(current_tx_ptr->packet + skb->len + 2));
+		}
 	}
 
 	/* enable this packet's dma */
@@ -691,7 +742,6 @@ static void bfin_mac_rx(struct net_device *dev)
 					 (unsigned long)skb->tail);
 
 	dev->last_rx = jiffies;
-	skb->dev = dev;
 	skb->protocol = eth_type_trans(skb, dev);
 #if defined(BFIN_MAC_CSUM_OFFLOAD)
 	skb->csum = current_rx_ptr->status.ip_payload_csum;
@@ -920,6 +970,7 @@ static int bfin_mac_open(struct net_device *dev)
 	phy_start(lp->phydev);
 	phy_write(lp->phydev, MII_BMCR, BMCR_RESET);
 	setup_system_regs(dev);
+	setup_mac_addr(dev->dev_addr);
 	bfin_mac_disable();
 	bfin_mac_enable();
 	pr_debug("hardware init finished\n");
@@ -955,7 +1006,7 @@ static int bfin_mac_close(struct net_device *dev)
 	return 0;
 }
 
-static int __init bfin_mac_probe(struct platform_device *pdev)
+static int __devinit bfin_mac_probe(struct platform_device *pdev)
 {
 	struct net_device *ndev;
 	struct bfin_mac_local *lp;
@@ -1081,7 +1132,7 @@ static int __init bfin_mac_probe(struct platform_device *pdev)
 	return rc;
 }
 
-static int bfin_mac_remove(struct platform_device *pdev)
+static int __devexit bfin_mac_remove(struct platform_device *pdev)
 {
 	struct net_device *ndev = platform_get_drvdata(pdev);
 	struct bfin_mac_local *lp = netdev_priv(ndev);
@@ -1128,7 +1179,7 @@ static int bfin_mac_resume(struct platform_device *pdev)
 
 static struct platform_driver bfin_mac_driver = {
 	.probe = bfin_mac_probe,
-	.remove = bfin_mac_remove,
+	.remove = __devexit_p(bfin_mac_remove),
 	.resume = bfin_mac_resume,
 	.suspend = bfin_mac_suspend,
 	.driver = {

drivers/net/cxgb3/t3_hw.c

@@ -683,7 +683,7 @@ enum {
 	SF_ERASE_SECTOR = 0xd8,	/* erase sector */
 
 	FW_FLASH_BOOT_ADDR = 0x70000,	/* start address of FW in flash */
-	FW_VERS_ADDR = 0x77ffc,    /* flash address holding FW version */
+	FW_VERS_ADDR = 0x7fffc,    /* flash address holding FW version */
 	FW_MIN_SIZE = 8            /* at least version and csum */
 };
 

drivers/net/ehea/ehea_main.c

@@ -2937,9 +2937,9 @@ static void ehea_rereg_mrs(struct work_struct *work)
 				}
 			}
 		}
-       mutex_unlock(&dlpar_mem_lock);
 	ehea_info("re-initializing driver complete");
 out:
+	mutex_unlock(&dlpar_mem_lock);
 	return;
 }
 

drivers/net/enc28j60.c

@@ -1547,8 +1547,10 @@ static int __devinit enc28j60_probe(struct spi_device *spi)
 	random_ether_addr(dev->dev_addr);
 	enc28j60_set_hw_macaddr(dev);
 
-	ret = request_irq(spi->irq, enc28j60_irq, IRQF_TRIGGER_FALLING,
-			  DRV_NAME, priv);
+	/* Board setup must set the relevant edge trigger type;
+	 * level triggers won't currently work.
+	 */
+	ret = request_irq(spi->irq, enc28j60_irq, 0, DRV_NAME, priv);
 	if (ret < 0) {
 		if (netif_msg_probe(priv))
 			dev_err(&spi->dev, DRV_NAME ": request irq %d failed "

drivers/net/forcedeth.c

@@ -333,6 +333,7 @@ enum {
 	NvRegPowerState2 = 0x600,
 #define NVREG_POWERSTATE2_POWERUP_MASK		0x0F11
 #define NVREG_POWERSTATE2_POWERUP_REV_A3	0x0001
+#define NVREG_POWERSTATE2_PHY_RESET		0x0004
 };
 
 /* Big endian: should work, but is untested */
@@ -529,6 +530,7 @@ union ring_type {
 #define PHY_REALTEK_INIT_REG4	0x14
 #define PHY_REALTEK_INIT_REG5	0x18
 #define PHY_REALTEK_INIT_REG6	0x11
+#define PHY_REALTEK_INIT_REG7	0x01
 #define PHY_REALTEK_INIT1	0x0000
 #define PHY_REALTEK_INIT2	0x8e00
 #define PHY_REALTEK_INIT3	0x0001
@@ -537,6 +539,9 @@ union ring_type {
 #define PHY_REALTEK_INIT6	0xf5c7
 #define PHY_REALTEK_INIT7	0x1000
 #define PHY_REALTEK_INIT8	0x0003
+#define PHY_REALTEK_INIT9	0x0008
+#define PHY_REALTEK_INIT10	0x0005
+#define PHY_REALTEK_INIT11	0x0200
 #define PHY_REALTEK_INIT_MSK1	0x0003
 
 #define PHY_GIGABIT	0x0100
@@ -1149,6 +1154,42 @@ static int phy_init(struct net_device *dev)
 				return PHY_ERROR;
 			}
 		}
+		if (np->phy_model == PHY_MODEL_REALTEK_8211 &&
+		    np->phy_rev == PHY_REV_REALTEK_8211C) {
+			u32 powerstate = readl(base + NvRegPowerState2);
+
+			/* need to perform hw phy reset */
+			powerstate |= NVREG_POWERSTATE2_PHY_RESET;
+			writel(powerstate, base + NvRegPowerState2);
+			msleep(25);
+
+			powerstate &= ~NVREG_POWERSTATE2_PHY_RESET;
+			writel(powerstate, base + NvRegPowerState2);
+			msleep(25);
+
+			reg = mii_rw(dev, np->phyaddr, PHY_REALTEK_INIT_REG6, MII_READ);
+			reg |= PHY_REALTEK_INIT9;
+			if (mii_rw(dev, np->phyaddr, PHY_REALTEK_INIT_REG6, reg)) {
+				printk(KERN_INFO "%s: phy init failed.\n", pci_name(np->pci_dev));
+				return PHY_ERROR;
+			}
+			if (mii_rw(dev, np->phyaddr, PHY_REALTEK_INIT_REG1, PHY_REALTEK_INIT10)) {
+				printk(KERN_INFO "%s: phy init failed.\n", pci_name(np->pci_dev));
+				return PHY_ERROR;
+			}
+			reg = mii_rw(dev, np->phyaddr, PHY_REALTEK_INIT_REG7, MII_READ);
+			if (!(reg & PHY_REALTEK_INIT11)) {
+				reg |= PHY_REALTEK_INIT11;
+				if (mii_rw(dev, np->phyaddr, PHY_REALTEK_INIT_REG7, reg)) {
+					printk(KERN_INFO "%s: phy init failed.\n", pci_name(np->pci_dev));
+					return PHY_ERROR;
+				}
+			}
+			if (mii_rw(dev, np->phyaddr, PHY_REALTEK_INIT_REG1, PHY_REALTEK_INIT1)) {
+				printk(KERN_INFO "%s: phy init failed.\n", pci_name(np->pci_dev));
+				return PHY_ERROR;
+			}
+		}
 		if (np->phy_model == PHY_MODEL_REALTEK_8201) {
 			if (np->device_id == PCI_DEVICE_ID_NVIDIA_NVENET_32 ||
 			    np->device_id == PCI_DEVICE_ID_NVIDIA_NVENET_33 ||
@@ -1201,6 +1242,16 @@ static int phy_init(struct net_device *dev)
 	mii_control = mii_rw(dev, np->phyaddr, MII_BMCR, MII_READ);
 	mii_control |= BMCR_ANENABLE;
 
+	if (np->phy_oui == PHY_OUI_REALTEK &&
+	    np->phy_model == PHY_MODEL_REALTEK_8211 &&
+	    np->phy_rev == PHY_REV_REALTEK_8211C) {
+		/* start autoneg since we already performed hw reset above */
+		mii_control |= BMCR_ANRESTART;
+		if (mii_rw(dev, np->phyaddr, MII_BMCR, mii_control)) {
+			printk(KERN_INFO "%s: phy init failed\n", pci_name(np->pci_dev));
+			return PHY_ERROR;
+		}
+	} else {
 		/* reset the phy
 		 * (certain phys need bmcr to be setup with reset)
 		 */
@@ -1208,6 +1259,7 @@ static int phy_init(struct net_device *dev)
 			printk(KERN_INFO "%s: phy reset failed\n", pci_name(np->pci_dev));
 			return PHY_ERROR;
 		}
+	}
 
 	/* phy vendor specific configuration */
 	if ((np->phy_oui == PHY_OUI_CICADA) && (phyinterface & PHY_RGMII) ) {

drivers/net/ne.c

@@ -536,7 +536,7 @@ static int __init ne_probe1(struct net_device *dev, unsigned long ioaddr)
 #ifdef CONFIG_NET_POLL_CONTROLLER
 	dev->poll_controller = eip_poll;
 #endif
-	NS8390_init(dev, 0);
+	NS8390p_init(dev, 0);
 
 	ret = register_netdev(dev);
 	if (ret)
@@ -794,7 +794,7 @@ static void ne_block_output(struct net_device *dev, int count,
 		if (time_after(jiffies, dma_start + 2*HZ/100)) {		/* 20ms */
 			printk(KERN_WARNING "%s: timeout waiting for Tx RDC.\n", dev->name);
 			ne_reset_8390(dev);
-			NS8390_init(dev,1);
+			NS8390p_init(dev, 1);
 			break;
 		}
 
@@ -855,7 +855,7 @@ static int ne_drv_resume(struct platform_device *pdev)
 
 	if (netif_running(dev)) {
 		ne_reset_8390(dev);
-		NS8390_init(dev, 1);
+		NS8390p_init(dev, 1);
 		netif_device_attach(dev);
 	}
 	return 0;

drivers/net/s2io.c

@@ -3143,7 +3143,7 @@ static void tx_intr_handler(struct fifo_info *fifo_data)
 		pkt_cnt++;
 
 		/* Updating the statistics block */
-		nic->stats.tx_bytes += skb->len;
+		nic->dev->stats.tx_bytes += skb->len;
 		nic->mac_control.stats_info->sw_stat.mem_freed += skb->truesize;
 		dev_kfree_skb_irq(skb);
 
@@ -4896,25 +4896,42 @@ static struct net_device_stats *s2io_get_stats(struct net_device *dev)
 	/* Configure Stats for immediate updt */
 	s2io_updt_stats(sp);
 
+	/* Using sp->stats as a staging area, because reset (due to mtu
+	   change, for example) will clear some hardware counters */
+	dev->stats.tx_packets +=
+		le32_to_cpu(mac_control->stats_info->tmac_frms) - 
+		sp->stats.tx_packets;
 	sp->stats.tx_packets =
 		le32_to_cpu(mac_control->stats_info->tmac_frms);
+	dev->stats.tx_errors +=
+		le32_to_cpu(mac_control->stats_info->tmac_any_err_frms) -
+		sp->stats.tx_errors;
 	sp->stats.tx_errors =
 		le32_to_cpu(mac_control->stats_info->tmac_any_err_frms);
+	dev->stats.rx_errors +=
+		le64_to_cpu(mac_control->stats_info->rmac_drop_frms) -
+		sp->stats.rx_errors;
 	sp->stats.rx_errors =
 		le64_to_cpu(mac_control->stats_info->rmac_drop_frms);
+	dev->stats.multicast =
+		le32_to_cpu(mac_control->stats_info->rmac_vld_mcst_frms) - 
+		sp->stats.multicast;
 	sp->stats.multicast =
 		le32_to_cpu(mac_control->stats_info->rmac_vld_mcst_frms);
+	dev->stats.rx_length_errors =
+		le64_to_cpu(mac_control->stats_info->rmac_long_frms) - 
+		sp->stats.rx_length_errors;
 	sp->stats.rx_length_errors =
 		le64_to_cpu(mac_control->stats_info->rmac_long_frms);
 
 	/* collect per-ring rx_packets and rx_bytes */
-	sp->stats.rx_packets = sp->stats.rx_bytes = 0;
+	dev->stats.rx_packets = dev->stats.rx_bytes = 0;
 	for (i = 0; i < config->rx_ring_num; i++) {
-		sp->stats.rx_packets += mac_control->rings[i].rx_packets;
-		sp->stats.rx_bytes += mac_control->rings[i].rx_bytes;
+		dev->stats.rx_packets += mac_control->rings[i].rx_packets;
+		dev->stats.rx_bytes += mac_control->rings[i].rx_bytes;
 	}
 
-	return (&sp->stats);
+	return (&dev->stats);
 }
 
 /**
@@ -7419,7 +7436,7 @@ static int rx_osm_handler(struct ring_info *ring_data, struct RxD_t * rxdp)
 		if (err_mask != 0x5) {
 			DBG_PRINT(ERR_DBG, "%s: Rx error Value: 0x%x\n",
 				dev->name, err_mask);
-			sp->stats.rx_crc_errors++;
+			dev->stats.rx_crc_errors++;
 			sp->mac_control.stats_info->sw_stat.mem_freed
 				+= skb->truesize;
 			dev_kfree_skb(skb);

drivers/net/usb/dm9601.c

@@ -55,12 +55,28 @@
 
 static int dm_read(struct usbnet *dev, u8 reg, u16 length, void *data)
 {
+	void *buf;
+	int err = -ENOMEM;
+
 	devdbg(dev, "dm_read() reg=0x%02x length=%d", reg, length);
-	return usb_control_msg(dev->udev,
+
+	buf = kmalloc(length, GFP_KERNEL);
+	if (!buf)
+		goto out;
+
+	err = usb_control_msg(dev->udev,
 			      usb_rcvctrlpipe(dev->udev, 0),
 			      DM_READ_REGS,
 			      USB_DIR_IN | USB_TYPE_VENDOR | USB_RECIP_DEVICE,
-			       0, reg, data, length, USB_CTRL_SET_TIMEOUT);
+			      0, reg, buf, length, USB_CTRL_SET_TIMEOUT);
+	if (err == length)
+		memcpy(data, buf, length);
+	else if (err >= 0)
+		err = -EINVAL;
+	kfree(buf);
+
+ out:
+	return err;
 }
 
 static int dm_read_reg(struct usbnet *dev, u8 reg, u8 *value)
@@ -70,12 +86,28 @@ static int dm_read_reg(struct usbnet *dev, u8 reg, u8 *value)
 
 static int dm_write(struct usbnet *dev, u8 reg, u16 length, void *data)
 {
+	void *buf = NULL;
+	int err = -ENOMEM;
+
 	devdbg(dev, "dm_write() reg=0x%02x, length=%d", reg, length);
-	return usb_control_msg(dev->udev,
+
+	if (data) {
+		buf = kmalloc(length, GFP_KERNEL);
+		if (!buf)
+			goto out;
+		memcpy(buf, data, length);
+	}
+
+	err = usb_control_msg(dev->udev,
 			      usb_sndctrlpipe(dev->udev, 0),
 			      DM_WRITE_REGS,
 			      USB_DIR_OUT | USB_TYPE_VENDOR |USB_RECIP_DEVICE,
-			       0, reg, data, length, USB_CTRL_SET_TIMEOUT);
+			      0, reg, buf, length, USB_CTRL_SET_TIMEOUT);
+	kfree(buf);
+	if (err >= 0 && err < length)
+		err = -EINVAL;
+ out:
+	return err;
 }
 
 static int dm_write_reg(struct usbnet *dev, u8 reg, u8 value)

drivers/net/wd.c

@@ -337,7 +337,7 @@ static int __init wd_probe1(struct net_device *dev, int ioaddr)
 #ifdef CONFIG_NET_POLL_CONTROLLER
 	dev->poll_controller = ei_poll;
 #endif
-	NS8390_init(dev, 0);
+	NS8390p_init(dev, 0);
 
 #if 1
 	/* Enable interrupt generation on softconfig cards -- M.U */