spi: spi-zynqmp-gqspi: Fix incorrect indentation

Fixed incorrect indentation in ZynqMP qspi controller driver.
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/2b246b6f0925c8a2a767a4240e8738ffeefd62be.1600931476.git.michal.simek@xilinx.comSigned-off-by: Mark Brown <broonie@kernel.org>

drivers/spi/spi-zynqmp-gqspi.c

@@ -386,7 +386,6 @@ static void zynqmp_qspi_chipselect(struct spi_device *qspi, bool is_high)
 		if ((statusreg & GQSPI_ISR_GENFIFOEMPTY_MASK) &&
 		    (statusreg & GQSPI_ISR_TXEMPTY_MASK))
 			break;
-		else
 		cpu_relax();
 	} while (!time_after_eq(jiffies, timeout));
 
@@ -549,7 +548,7 @@ static void zynqmp_qspi_readrxfifo(struct zynqmp_qspi *xqspi, u32 size)
 
 	while ((count < size) && (xqspi->bytes_to_receive > 0)) {
 		if (xqspi->bytes_to_receive >= 4) {
-			(*(u32 *) xqspi->rxbuf) =
+			(*(u32 *)xqspi->rxbuf) =
 			zynqmp_gqspi_read(xqspi, GQSPI_RXD_OFST);
 			xqspi->rxbuf += 4;
 			xqspi->bytes_to_receive -= 4;
@@ -670,7 +669,8 @@ static void zynqmp_process_dma_irq(struct zynqmp_qspi *xqspi)
 
 		/* Manual start */
 		zynqmp_gqspi_write(xqspi, GQSPI_CONFIG_OFST,
-			(zynqmp_gqspi_read(xqspi, GQSPI_CONFIG_OFST) |
+				   (zynqmp_gqspi_read(xqspi,
+						      GQSPI_CONFIG_OFST) |
 				   GQSPI_CFG_START_GEN_FIFO_MASK));
 
 		/* Enable the RX interrupts for IO mode */
@@ -725,8 +725,8 @@ static irqreturn_t zynqmp_qspi_irq(int irq, void *dev_id)
 		ret = IRQ_HANDLED;
 	}
 
-	if ((xqspi->bytes_to_receive == 0) && (xqspi->bytes_to_transfer == 0)
-			&& ((status & GQSPI_IRQ_MASK) == GQSPI_IRQ_MASK)) {
+	if (xqspi->bytes_to_receive == 0 && xqspi->bytes_to_transfer == 0 &&
+	    ((status & GQSPI_IRQ_MASK) == GQSPI_IRQ_MASK)) {
 		zynqmp_gqspi_write(xqspi, GQSPI_IDR_OFST, GQSPI_ISR_IDR_MASK);
 		complete(&xqspi->data_completion);
 		ret = IRQ_HANDLED;
@@ -744,7 +744,7 @@ static void zynqmp_qspi_setuprxdma(struct zynqmp_qspi *xqspi)
 	dma_addr_t addr;
 	u64 dma_align =  (u64)(uintptr_t)xqspi->rxbuf;
 
-	if ((xqspi->bytes_to_receive < 8) ||
+	if (xqspi->bytes_to_receive < 8 ||
 	    ((dma_align & GQSPI_DMA_UNALIGN) != 0x0)) {
 		/* Setting to IO mode */
 		config_reg = zynqmp_gqspi_read(xqspi, GQSPI_CONFIG_OFST);