Merge tag 'omap-for-v3.15/fixes-v2-signed' of...

Merge tag 'omap-for-v3.15/fixes-v2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes

Fixes for omaps, mostly to fix some GPMC, DSS and USB issues for
device tree based booting. And turns out BeagleBoard xM A/B
needs it's own minimal dts in addition to the related u-boot
changes. Also few minor documentation and typo fixes are merged
to get them out of the way.

* tag 'omap-for-v3.15/fixes-v2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: OMAP2+: Fix GPMC remap for devices using an offset
  ARM: OMAP2+: Fix oops for GPMC free
  ARM: dts: Add support for the BeagleBoard xM A/B
  ARM: dts: Grammar /that will/it will/
  ARM: dts: Grammar /is uses/ is used/
  ARM: OMAP2+: Fix config name for USB3 PHY
  ARM: dts: am335x: update USB DT references
  ARM: dts: OMAP2+: remove uses of obsolete gpmc,device-nand
  ARM: AM335X: EVM: fix pinmux documentation in devicetree
  ARM: OMAP2+: N900: remove omapdss init for DT boot
  ARM: dts: dra7xx-clocks: Correct mcasp2_ahclkx_mux bit-shift
  ARM: dts: omap5: Add clocks to USB3 PHY node
  ARM: OMAP2+: hwmod: fix missing braces in _init()
  ARM: AM43xx: fix dpll init in bypass mode
  ARM: OMAP3: hwmod data: Correct clock domains for USB modules
  ARM: OMAP3: PM: remove access to PRM_VOLTCTRL register
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

arch/arm/boot/dts/Makefile

@@ -245,6 +245,7 @@ dtb-$(CONFIG_ARCH_OMAP2PLUS) += omap2420-h4.dtb \
 	omap3-sbc-t3730.dtb \
 	omap3-devkit8000.dtb \
 	omap3-beagle-xm.dtb \
+	omap3-beagle-xm-ab.dtb \
 	omap3-evm.dtb \
 	omap3-evm-37xx.dtb \
 	omap3-ldp.dtb \

arch/arm/boot/dts/am335x-bone-common.dtsi

@@ -183,7 +183,7 @@ &uart0 {
 &usb {
 	status = "okay";
 
-	control@44e10000 {
+	control@44e10620 {
 		status = "okay";
 	};
 
@@ -204,7 +204,7 @@ usb@47401800 {
 		dr_mode = "host";
 	};
 
-	dma-controller@07402000  {
+	dma-controller@47402000  {
 		status = "okay";
 	};
 };

arch/arm/boot/dts/am335x-evm.dts

@@ -301,8 +301,8 @@ lcd_pins_s0: lcd_pins_s0 {
 
 	am335x_evm_audio_pins: am335x_evm_audio_pins {
 		pinctrl-single,pins = <
-			0x10c (PIN_INPUT_PULLDOWN | MUX_MODE4) /* mii1_rx_dv.mcasp1_aclkx */
-			0x110 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* mii1_txd3.mcasp1_fsx */
+			0x10c (PIN_INPUT_PULLDOWN | MUX_MODE4) /* mii1_crs.mcasp1_aclkx */
+			0x110 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* mii1_rxerr.mcasp1_fsx */
 			0x108 (PIN_OUTPUT_PULLDOWN | MUX_MODE4) /* mii1_col.mcasp1_axr2 */
 			0x144 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* rmii1_ref_clk.mcasp1_axr3 */
 		>;
@@ -331,7 +331,7 @@ tps: tps@2d {
 &usb {
 	status = "okay";
 
-	control@44e10000 {
+	control@44e10620 {
 		status = "okay";
 	};
 
@@ -352,7 +352,7 @@ usb@47401800 {
 		dr_mode = "host";
 	};
 
-	dma-controller@07402000  {
+	dma-controller@47402000  {
 		status = "okay";
 	};
 };

arch/arm/boot/dts/am335x-evmsk.dts

@@ -364,7 +364,7 @@ tlv320aic3106: tlv320aic3106@1b {
 &usb {
 	status = "okay";
 
-	control@44e10000 {
+	control@44e10620 {
 		status = "okay";
 	};
 
@@ -385,7 +385,7 @@ usb@47401800 {
 		dr_mode = "host";
 	};
 
-	dma-controller@07402000  {
+	dma-controller@47402000  {
 		status = "okay";
 	};
 };

arch/arm/boot/dts/am335x-igep0033.dtsi

@@ -118,7 +118,6 @@ nand@0,0 {
 		reg = <0 0 0>; /* CS0, offset 0 */
 		nand-bus-width = <8>;
 		ti,nand-ecc-opt = "bch8";
-		gpmc,device-nand = "true";
 		gpmc,device-width = <1>;
 		gpmc,sync-clk-ps = <0>;
 		gpmc,cs-on-ns = <0>;
@@ -202,7 +201,7 @@ &uart0 {
 &usb {
 	status = "okay";
 
-	control@44e10000 {
+	control@44e10620 {
 		status = "okay";
 	};
 
@@ -223,7 +222,7 @@ usb@47401800 {
 		dr_mode = "host";
 	};
 
-	dma-controller@07402000  {
+	dma-controller@47402000  {
 		status = "okay";
 	};
 };

arch/arm/boot/dts/am33xx.dtsi

@@ -72,7 +72,7 @@ pmu {
 	};
 
 	/*
-	 * The soc node represents the soc top level view. It is uses for IPs
+	 * The soc node represents the soc top level view. It is used for IPs
 	 * that are not memory mapped in the MPU view or for the MPU itself.
 	 */
 	soc {
@@ -94,8 +94,8 @@ am33xx_pinmux: pinmux@44e10800 {
 
 	/*
 	 * XXX: Use a flat representation of the AM33XX interconnect.
-	 * The real AM33XX interconnect network is quite complex.Since
-	 * that will not bring real advantage to represent that in DT
+	 * The real AM33XX interconnect network is quite complex. Since
+	 * it will not bring real advantage to represent that in DT
 	 * for the moment, just use a fake OCP bus entry to represent
 	 * the whole bus hierarchy.
 	 */

arch/arm/boot/dts/dra7.dtsi

@@ -80,7 +80,7 @@ gic: interrupt-controller@48211000 {
 	};
 
 	/*
-	 * The soc node represents the soc top level view. It is uses for IPs
+	 * The soc node represents the soc top level view. It is used for IPs
 	 * that are not memory mapped in the MPU view or for the MPU itself.
 	 */
 	soc {
@@ -94,7 +94,7 @@ mpu {
 	/*
 	 * XXX: Use a flat representation of the SOC interconnect.
 	 * The real OMAP interconnect network is quite complex.
-	 * Since that will not bring real advantage to represent that in DT for
+	 * Since it will not bring real advantage to represent that in DT for
 	 * the moment, just use a fake OCP bus entry to represent the whole bus
 	 * hierarchy.
 	 */

arch/arm/boot/dts/dra7xx-clocks.dtsi

@@ -1640,7 +1640,7 @@ mcasp2_ahclkx_mux: mcasp2_ahclkx_mux {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
 		clocks = <&abe_24m_fclk>, <&abe_sys_clk_div>, <&func_24m_clk>, <&atlclkin3_ck>, <&atl_clkin2_ck>, <&atl_clkin1_ck>, <&atl_clkin0_ck>, <&sys_clkin2>, <&ref_clkin0_ck>, <&ref_clkin1_ck>, <&ref_clkin2_ck>, <&ref_clkin3_ck>, <&mlb_clk>, <&mlbp_clk>;
-		ti,bit-shift = <28>;
+		ti,bit-shift = <24>;
 		reg = <0x1860>;
 	};
 

arch/arm/boot/dts/omap3-beagle-xm-ab.dts

+/*
+ * Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include "omap3-beagle-xm.dts"
+
+/ {
+	/* HS USB Port 2 Power enable was inverted with the xM C */
+	hsusb2_power: hsusb2_power_reg {
+		enable-active-high;
+	};
+};

arch/arm/boot/dts/omap3-devkit8000.dts

@@ -112,7 +112,6 @@ nand@0,0 {
 		reg = <0 0 0>; /* CS0, offset 0 */
 		nand-bus-width = <16>;
 
-		gpmc,device-nand;
 		gpmc,sync-clk-ps = <0>;
 		gpmc,cs-on-ns = <0>;
 		gpmc,cs-rd-off-ns = <44>;

arch/arm/boot/dts/omap3-lilly-a83x.dtsi

@@ -368,7 +368,6 @@ nand@0,0 {
 		/* no elm on omap3 */
 
 		gpmc,mux-add-data = <0>;
-		gpmc,device-nand;
 		gpmc,device-width = <2>;
 		gpmc,wait-pin = <0>;
 		gpmc,wait-monitoring-ns = <0>;

arch/arm/boot/dts/omap3.dtsi

@@ -74,7 +74,7 @@ dsp {
 	/*
 	 * XXX: Use a flat representation of the OMAP3 interconnect.
 	 * The real OMAP interconnect network is quite complex.
-	 * Since that will not bring real advantage to represent that in DT for
+	 * Since it will not bring real advantage to represent that in DT for
 	 * the moment, just use a fake OCP bus entry to represent the whole bus
 	 * hierarchy.
 	 */

arch/arm/boot/dts/omap4.dtsi

@@ -72,7 +72,7 @@ local-timer@48240600 {
 	};
 
 	/*
-	 * The soc node represents the soc top level view. It is uses for IPs
+	 * The soc node represents the soc top level view. It is used for IPs
 	 * that are not memory mapped in the MPU view or for the MPU itself.
 	 */
 	soc {
@@ -96,7 +96,7 @@ iva {
 	/*
 	 * XXX: Use a flat representation of the OMAP4 interconnect.
 	 * The real OMAP interconnect network is quite complex.
-	 * Since that will not bring real advantage to represent that in DT for
+	 * Since it will not bring real advantage to represent that in DT for
 	 * the moment, just use a fake OCP bus entry to represent the whole bus
 	 * hierarchy.
 	 */

arch/arm/boot/dts/omap5.dtsi

@@ -93,7 +93,7 @@ gic: interrupt-controller@48211000 {
 	};
 
 	/*
-	 * The soc node represents the soc top level view. It is uses for IPs
+	 * The soc node represents the soc top level view. It is used for IPs
 	 * that are not memory mapped in the MPU view or for the MPU itself.
 	 */
 	soc {
@@ -107,7 +107,7 @@ mpu {
 	/*
 	 * XXX: Use a flat representation of the OMAP3 interconnect.
 	 * The real OMAP interconnect network is quite complex.
-	 * Since that will not bring real advantage to represent that in DT for
+	 * Since it will not bring real advantage to represent that in DT for
 	 * the moment, just use a fake OCP bus entry to represent the whole bus
 	 * hierarchy.
 	 */
@@ -813,6 +813,12 @@ usb3_phy: usb3phy@4a084400 {
 				      <0x4a084c00 0x40>;
 				reg-names = "phy_rx", "phy_tx", "pll_ctrl";
 				ctrl-module = <&omap_control_usb3phy>;
+				clocks = <&usb_phy_cm_clk32k>,
+					 <&sys_clkin>,
+					 <&usb_otg_ss_refclk960m>;
+				clock-names =	"wkupclk",
+						"sysclk",
+						"refclk";
 				#phy-cells = <0>;
 			};
 		};

arch/arm/configs/omap2plus_defconfig

@@ -226,7 +226,7 @@ CONFIG_USB_DWC3=m
 CONFIG_USB_TEST=y
 CONFIG_NOP_USB_XCEIV=y
 CONFIG_OMAP_USB2=y
-CONFIG_OMAP_USB3=y
+CONFIG_TI_PIPE3=y
 CONFIG_AM335X_PHY_USB=y
 CONFIG_USB_GADGET=y
 CONFIG_USB_GADGET_DEBUG=y

arch/arm/mach-omap2/board-rx51-video.c

@@ -48,7 +48,7 @@ static struct omap_dss_board_info rx51_dss_board_info = {
 
 static int __init rx51_video_init(void)
 {
-	if (!machine_is_nokia_rx51() && !of_machine_is_compatible("nokia,omap3-n900"))
+	if (!machine_is_nokia_rx51())
 		return 0;
 
 	if (omap_mux_init_gpio(RX51_LCD_RESET_GPIO, OMAP_PIN_OUTPUT)) {

arch/arm/mach-omap2/clkt_dpll.c

@@ -209,7 +209,7 @@ u8 omap2_init_dpll_parent(struct clk_hw *hw)
 		if (v == OMAP3XXX_EN_DPLL_LPBYPASS ||
 		    v == OMAP3XXX_EN_DPLL_FRBYPASS)
 			return 1;
-	} else if (soc_is_am33xx() || cpu_is_omap44xx()) {
+	} else if (soc_is_am33xx() || cpu_is_omap44xx() || soc_is_am43xx()) {
 		if (v == OMAP4XXX_EN_DPLL_LPBYPASS ||
 		    v == OMAP4XXX_EN_DPLL_FRBYPASS ||
 		    v == OMAP4XXX_EN_DPLL_MNBYPASS)
@@ -255,7 +255,7 @@ unsigned long omap2_get_dpll_rate(struct clk_hw_omap *clk)
 		if (v == OMAP3XXX_EN_DPLL_LPBYPASS ||
 		    v == OMAP3XXX_EN_DPLL_FRBYPASS)
 			return __clk_get_rate(dd->clk_bypass);
-	} else if (soc_is_am33xx() || cpu_is_omap44xx()) {
+	} else if (soc_is_am33xx() || cpu_is_omap44xx() || soc_is_am43xx()) {
 		if (v == OMAP4XXX_EN_DPLL_LPBYPASS ||
 		    v == OMAP4XXX_EN_DPLL_FRBYPASS ||
 		    v == OMAP4XXX_EN_DPLL_MNBYPASS)

arch/arm/mach-omap2/gpmc.c

@@ -501,7 +501,7 @@ static int gpmc_cs_delete_mem(int cs)
 	int r;
 
 	spin_lock(&gpmc_mem_lock);
-	r = release_resource(&gpmc_cs_mem[cs]);
+	r = release_resource(res);
 	res->start = 0;
 	res->end = 0;
 	spin_unlock(&gpmc_mem_lock);
@@ -527,6 +527,14 @@ static int gpmc_cs_remap(int cs, u32 base)
 		pr_err("%s: requested chip-select is disabled\n", __func__);
 		return -ENODEV;
 	}
+
+	/*
+	 * Make sure we ignore any device offsets from the GPMC partition
+	 * allocated for the chip select and that the new base confirms
+	 * to the GPMC 16MB minimum granularity.
+	 */ 
+	base &= ~(SZ_16M - 1);
+
 	gpmc_cs_get_memconf(cs, &old_base, &size);
 	if (base == old_base)
 		return 0;
@@ -586,6 +594,8 @@ EXPORT_SYMBOL(gpmc_cs_request);
 
 void gpmc_cs_free(int cs)
 {
+	struct resource	*res = &gpmc_cs_mem[cs];
+
 	spin_lock(&gpmc_mem_lock);
 	if (cs >= gpmc_cs_num || cs < 0 || !gpmc_cs_reserved(cs)) {
 		printk(KERN_ERR "Trying to free non-reserved GPMC CS%d\n", cs);
@@ -594,7 +604,8 @@ void gpmc_cs_free(int cs)
 		return;
 	}
 	gpmc_cs_disable_mem(cs);
-	release_resource(&gpmc_cs_mem[cs]);
+	if (res->flags)
+		release_resource(res);
 	gpmc_cs_set_reserved(cs, 0);
 	spin_unlock(&gpmc_mem_lock);
 }

arch/arm/mach-omap2/omap_hwmod.c

@@ -2546,11 +2546,12 @@ static int __init _init(struct omap_hwmod *oh, void *data)
 		return -EINVAL;
 	}
 
-	if (np)
+	if (np) {
 		if (of_find_property(np, "ti,no-reset-on-init", NULL))
 			oh->flags |= HWMOD_INIT_NO_RESET;
 		if (of_find_property(np, "ti,no-idle-on-init", NULL))
 			oh->flags |= HWMOD_INIT_NO_IDLE;
+	}
 
 	oh->_state = _HWMOD_STATE_INITIALIZED;
 

arch/arm/mach-omap2/omap_hwmod_3xxx_data.c

@@ -1964,7 +1964,7 @@ static struct omap_hwmod_irq_info omap3xxx_usb_host_hs_irqs[] = {
 static struct omap_hwmod omap3xxx_usb_host_hs_hwmod = {
 	.name		= "usb_host_hs",
 	.class		= &omap3xxx_usb_host_hs_hwmod_class,
-	.clkdm_name	= "l3_init_clkdm",
+	.clkdm_name	= "usbhost_clkdm",
 	.mpu_irqs	= omap3xxx_usb_host_hs_irqs,
 	.main_clk	= "usbhost_48m_fck",
 	.prcm = {
@@ -2047,7 +2047,7 @@ static struct omap_hwmod_irq_info omap3xxx_usb_tll_hs_irqs[] = {
 static struct omap_hwmod omap3xxx_usb_tll_hs_hwmod = {
 	.name		= "usb_tll_hs",
 	.class		= &omap3xxx_usb_tll_hs_hwmod_class,
-	.clkdm_name	= "l3_init_clkdm",
+	.clkdm_name	= "core_l4_clkdm",
 	.mpu_irqs	= omap3xxx_usb_tll_hs_irqs,
 	.main_clk	= "usbtll_fck",
 	.prcm = {

arch/arm/mach-omap2/pm34xx.c

@@ -330,10 +330,6 @@ void omap_sram_idle(void)
 			omap3_sram_restore_context();
 			omap2_sms_restore_context();
 		}
-		if (core_next_state == PWRDM_POWER_OFF)
-			omap2_prm_clear_mod_reg_bits(OMAP3430_AUTO_OFF_MASK,
-					       OMAP3430_GR_MOD,
-					       OMAP3_PRM_VOLTCTRL_OFFSET);
 	}
 	omap3_intc_resume_idle();