Commit f29af978 authored by Kalle Valo's avatar Kalle Valo

ath6kl: add ATH6KL_CONF_UART_DEBUG

Add ATH6KL_CONF_UART_DEBUG which is set whenever uart_debug module
parameter is enabled. This way we can keep the uart_debug parameter
static when core.c file is introduced.
Signed-off-by: default avatarKalle Valo <kvalo@qca.qualcomm.com>
parent 46d33a21
...@@ -197,6 +197,7 @@ struct ath6kl_fw_ie { ...@@ -197,6 +197,7 @@ struct ath6kl_fw_ie {
#define ATH6KL_CONF_ENABLE_11N BIT(2) #define ATH6KL_CONF_ENABLE_11N BIT(2)
#define ATH6KL_CONF_ENABLE_TX_BURST BIT(3) #define ATH6KL_CONF_ENABLE_TX_BURST BIT(3)
#define ATH6KL_CONF_SUSPEND_CUTPOWER BIT(4) #define ATH6KL_CONF_SUSPEND_CUTPOWER BIT(4)
#define ATH6KL_CONF_UART_DEBUG BIT(5)
enum wlan_low_pwr_state { enum wlan_low_pwr_state {
WLAN_POWER_STATE_ON, WLAN_POWER_STATE_ON,
......
...@@ -469,7 +469,7 @@ int ath6kl_configure_target(struct ath6kl *ar) ...@@ -469,7 +469,7 @@ int ath6kl_configure_target(struct ath6kl *ar)
u8 fw_iftype, fw_mode = 0, fw_submode = 0; u8 fw_iftype, fw_mode = 0, fw_submode = 0;
int i, status; int i, status;
param = uart_debug; param = !!(ar->conf_flags & ATH6KL_CONF_UART_DEBUG);
if (ath6kl_bmi_write(ar, ath6kl_get_hi_item_addr(ar, if (ath6kl_bmi_write(ar, ath6kl_get_hi_item_addr(ar,
HI_ITEM(hi_serial_enable)), (u8 *)&param, 4)) { HI_ITEM(hi_serial_enable)), (u8 *)&param, 4)) {
ath6kl_err("bmi_write_memory for uart debug failed\n"); ath6kl_err("bmi_write_memory for uart debug failed\n");
...@@ -1775,6 +1775,9 @@ int ath6kl_core_init(struct ath6kl *ar) ...@@ -1775,6 +1775,9 @@ int ath6kl_core_init(struct ath6kl *ar)
if (suspend_cutpower) if (suspend_cutpower)
ar->conf_flags |= ATH6KL_CONF_SUSPEND_CUTPOWER; ar->conf_flags |= ATH6KL_CONF_SUSPEND_CUTPOWER;
if (uart_debug)
ar->conf_flags |= ATH6KL_CONF_UART_DEBUG;
ar->wiphy->flags |= WIPHY_FLAG_SUPPORTS_FW_ROAM | ar->wiphy->flags |= WIPHY_FLAG_SUPPORTS_FW_ROAM |
WIPHY_FLAG_HAVE_AP_SME | WIPHY_FLAG_HAVE_AP_SME |
WIPHY_FLAG_HAS_REMAIN_ON_CHANNEL | WIPHY_FLAG_HAS_REMAIN_ON_CHANNEL |
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment