Merge remote-tracking branches 'regulator/topic/isl9305',...

Merge remote-tracking branches 'regulator/topic/isl9305', 'regulator/topic/lp872x', 'regulator/topic/max14577', 'regulator/topic/max7686' and 'regulator/topic/max77843' into regulator-next

Documentation/devicetree/bindings/mfd/max77686.txt

@@ -39,6 +39,12 @@ to get matched with their hardware counterparts as follow:
 	-BUCKn	:	1-4.
   Use standard regulator bindings for it ('regulator-off-in-suspend').
 
+  LDO20, LDO21, LDO22, BUCK8 and BUCK9 can be configured to GPIO enable
+  control. To turn this feature on this property must be added to the regulator
+  sub-node:
+	- maxim,ena-gpios :	one GPIO specifier enable control (the gpio
+				flags are actually ignored and always
+				ACTIVE_HIGH is used)
 
 Example:
 
@@ -65,4 +71,12 @@ Example:
 				regulator-always-on;
 				regulator-boot-on;
 			};
+
+			buck9_reg {
+				regulator-compatible = "BUCK9";
+				regulator-name = "CAM_ISP_CORE_1.2V";
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1200000>;
+				maxim,ena-gpios = <&gpm0 3 GPIO_ACTIVE_HIGH>;
+			};
 	}

Documentation/devicetree/bindings/regulator/isl9305.txt

@@ -2,7 +2,7 @@ Intersil ISL9305/ISL9305H voltage regulator
 
 Required properties:
 
-- compatible: "isl,isl9305" or "isl,isl9305h"
+- compatible: "isil,isl9305" or "isil,isl9305h"
 - reg: I2C slave address, usually 0x68.
 - regulators: A node that houses a sub-node for each regulator within the
   device. Each sub-node is identified using the node's name, with valid
@@ -19,7 +19,7 @@ Optional properties:
 Example
 
 	pmic: isl9305@68 {
-		compatible = "isl,isl9305";
+		compatible = "isil,isl9305";
 		reg = <0x68>;
 
 		VINDCD1-supply = <&system_power>;

drivers/regulator/Kconfig

@@ -414,6 +414,14 @@ config REGULATOR_MAX77802
 	  Exynos5420/Exynos5800 SoCs to control various voltages.
 	  It includes support for control of voltage and ramp speed.
 
+config REGULATOR_MAX77843
+	tristate "Maxim 77843 regulator"
+	depends on MFD_MAX77843
+	help
+	  This driver controls a Maxim 77843 regulator.
+	  The regulator include two 'SAFEOUT' for USB(Universal Serial Bus)
+	  This is suitable for Exynos5433 SoC chips.
+
 config REGULATOR_MC13XXX_CORE
 	tristate
 

drivers/regulator/Makefile

@@ -55,6 +55,7 @@ obj-$(CONFIG_REGULATOR_MAX8998) += max8998.o
 obj-$(CONFIG_REGULATOR_MAX77686) += max77686.o
 obj-$(CONFIG_REGULATOR_MAX77693) += max77693.o
 obj-$(CONFIG_REGULATOR_MAX77802) += max77802.o
+obj-$(CONFIG_REGULATOR_MAX77843) += max77843.o
 obj-$(CONFIG_REGULATOR_MC13783) += mc13783-regulator.o
 obj-$(CONFIG_REGULATOR_MC13892) += mc13892-regulator.o
 obj-$(CONFIG_REGULATOR_MC13XXX_CORE) +=  mc13xxx-regulator-core.o

drivers/regulator/isl9305.c

@@ -177,8 +177,10 @@ static int isl9305_i2c_probe(struct i2c_client *i2c,
 
 #ifdef CONFIG_OF
 static const struct of_device_id isl9305_dt_ids[] = {
-	{ .compatible = "isl,isl9305" },
-	{ .compatible = "isl,isl9305h" },
+	{ .compatible = "isl,isl9305" }, /* for backward compat., don't use */
+	{ .compatible = "isil,isl9305" },
+	{ .compatible = "isl,isl9305h" }, /* for backward compat., don't use */
+	{ .compatible = "isil,isl9305h" },
 	{},
 };
 #endif

drivers/regulator/lp872x.c

@@ -106,7 +106,6 @@ struct lp872x {
 	struct device *dev;
 	enum lp872x_id chipid;
 	struct lp872x_platform_data *pdata;
-	struct regulator_dev **regulators;
 	int num_regulators;
 	enum lp872x_dvs_state dvs_pin;
 	int dvs_gpio;
@@ -801,8 +800,6 @@ static int lp872x_regulator_register(struct lp872x *lp)
 			dev_err(lp->dev, "regulator register err");
 			return PTR_ERR(rdev);
 		}
-
-		*(lp->regulators + i) = rdev;
 	}
 
 	return 0;
@@ -906,7 +903,7 @@ static struct lp872x_platform_data
 static int lp872x_probe(struct i2c_client *cl, const struct i2c_device_id *id)
 {
 	struct lp872x *lp;
-	int ret, size, num_regulators;
+	int ret;
 	const int lp872x_num_regulators[] = {
 		[LP8720] = LP8720_NUM_REGULATORS,
 		[LP8725] = LP8725_NUM_REGULATORS,
@@ -918,38 +915,27 @@ static int lp872x_probe(struct i2c_client *cl, const struct i2c_device_id *id)
 
 	lp = devm_kzalloc(&cl->dev, sizeof(struct lp872x), GFP_KERNEL);
 	if (!lp)
-		goto err_mem;
-
-	num_regulators = lp872x_num_regulators[id->driver_data];
-	size = sizeof(struct regulator_dev *) * num_regulators;
+		return -ENOMEM;
 
-	lp->regulators = devm_kzalloc(&cl->dev, size, GFP_KERNEL);
-	if (!lp->regulators)
-		goto err_mem;
+	lp->num_regulators = lp872x_num_regulators[id->driver_data];
 
 	lp->regmap = devm_regmap_init_i2c(cl, &lp872x_regmap_config);
 	if (IS_ERR(lp->regmap)) {
 		ret = PTR_ERR(lp->regmap);
 		dev_err(&cl->dev, "regmap init i2c err: %d\n", ret);
-		goto err_dev;
+		return ret;
 	}
 
 	lp->dev = &cl->dev;
 	lp->pdata = dev_get_platdata(&cl->dev);
 	lp->chipid = id->driver_data;
-	lp->num_regulators = num_regulators;
 	i2c_set_clientdata(cl, lp);
 
 	ret = lp872x_config(lp);
 	if (ret)
-		goto err_dev;
+		return ret;
 
 	return lp872x_regulator_register(lp);
-
-err_mem:
-	return -ENOMEM;
-err_dev:
-	return ret;
 }
 
 static const struct of_device_id lp872x_dt_ids[] = {

drivers/regulator/max14577.c

@@ -103,6 +103,8 @@ static struct regulator_ops max14577_charger_ops = {
 static const struct regulator_desc max14577_supported_regulators[] = {
 	[MAX14577_SAFEOUT] = {
 		.name		= "SAFEOUT",
+		.of_match	= of_match_ptr("SAFEOUT"),
+		.regulators_node = of_match_ptr("regulators"),
 		.id		= MAX14577_SAFEOUT,
 		.ops		= &max14577_safeout_ops,
 		.type		= REGULATOR_VOLTAGE,
@@ -114,6 +116,8 @@ static const struct regulator_desc max14577_supported_regulators[] = {
 	},
 	[MAX14577_CHARGER] = {
 		.name		= "CHARGER",
+		.of_match	= of_match_ptr("CHARGER"),
+		.regulators_node = of_match_ptr("regulators"),
 		.id		= MAX14577_CHARGER,
 		.ops		= &max14577_charger_ops,
 		.type		= REGULATOR_CURRENT,
@@ -137,6 +141,8 @@ static struct regulator_ops max77836_ldo_ops = {
 static const struct regulator_desc max77836_supported_regulators[] = {
 	[MAX14577_SAFEOUT] = {
 		.name		= "SAFEOUT",
+		.of_match	= of_match_ptr("SAFEOUT"),
+		.regulators_node = of_match_ptr("regulators"),
 		.id		= MAX14577_SAFEOUT,
 		.ops		= &max14577_safeout_ops,
 		.type		= REGULATOR_VOLTAGE,
@@ -148,6 +154,8 @@ static const struct regulator_desc max77836_supported_regulators[] = {
 	},
 	[MAX14577_CHARGER] = {
 		.name		= "CHARGER",
+		.of_match	= of_match_ptr("CHARGER"),
+		.regulators_node = of_match_ptr("regulators"),
 		.id		= MAX14577_CHARGER,
 		.ops		= &max14577_charger_ops,
 		.type		= REGULATOR_CURRENT,
@@ -157,6 +165,8 @@ static const struct regulator_desc max77836_supported_regulators[] = {
 	},
 	[MAX77836_LDO1] = {
 		.name		= "LDO1",
+		.of_match	= of_match_ptr("LDO1"),
+		.regulators_node = of_match_ptr("regulators"),
 		.id		= MAX77836_LDO1,
 		.ops		= &max77836_ldo_ops,
 		.type		= REGULATOR_VOLTAGE,
@@ -171,6 +181,8 @@ static const struct regulator_desc max77836_supported_regulators[] = {
 	},
 	[MAX77836_LDO2] = {
 		.name		= "LDO2",
+		.of_match	= of_match_ptr("LDO2"),
+		.regulators_node = of_match_ptr("regulators"),
 		.id		= MAX77836_LDO2,
 		.ops		= &max77836_ldo_ops,
 		.type		= REGULATOR_VOLTAGE,
@@ -198,43 +210,6 @@ static struct of_regulator_match max77836_regulator_matches[] = {
 	{ .name = "LDO2", },
 };
 
-static int max14577_regulator_dt_parse_pdata(struct platform_device *pdev,
-		enum maxim_device_type dev_type)
-{
-	int ret;
-	struct device_node *np;
-	struct of_regulator_match *regulator_matches;
-	unsigned int regulator_matches_size;
-
-	np = of_get_child_by_name(pdev->dev.parent->of_node, "regulators");
-	if (!np) {
-		dev_err(&pdev->dev, "Failed to get child OF node for regulators\n");
-		return -EINVAL;
-	}
-
-	switch (dev_type) {
-	case MAXIM_DEVICE_TYPE_MAX77836:
-		regulator_matches = max77836_regulator_matches;
-		regulator_matches_size = ARRAY_SIZE(max77836_regulator_matches);
-		break;
-	case MAXIM_DEVICE_TYPE_MAX14577:
-	default:
-		regulator_matches = max14577_regulator_matches;
-		regulator_matches_size = ARRAY_SIZE(max14577_regulator_matches);
-	}
-
-	ret = of_regulator_match(&pdev->dev, np, regulator_matches,
-			regulator_matches_size);
-	if (ret < 0)
-		dev_err(&pdev->dev, "Error parsing regulator init data: %d\n", ret);
-	else
-		ret = 0;
-
-	of_node_put(np);
-
-	return ret;
-}
-
 static inline struct regulator_init_data *match_init_data(int index,
 		enum maxim_device_type dev_type)
 {
@@ -261,11 +236,6 @@ static inline struct device_node *match_of_node(int index,
 	}
 }
 #else /* CONFIG_OF */
-static int max14577_regulator_dt_parse_pdata(struct platform_device *pdev,
-		enum maxim_device_type dev_type)
-{
-	return 0;
-}
 static inline struct regulator_init_data *match_init_data(int index,
 		enum maxim_device_type dev_type)
 {
@@ -308,16 +278,12 @@ static int max14577_regulator_probe(struct platform_device *pdev)
 {
 	struct max14577 *max14577 = dev_get_drvdata(pdev->dev.parent);
 	struct max14577_platform_data *pdata = dev_get_platdata(max14577->dev);
-	int i, ret;
+	int i, ret = 0;
 	struct regulator_config config = {};
 	const struct regulator_desc *supported_regulators;
 	unsigned int supported_regulators_size;
 	enum maxim_device_type dev_type = max14577->dev_type;
 
-	ret = max14577_regulator_dt_parse_pdata(pdev, dev_type);
-	if (ret)
-		return ret;
-
 	switch (dev_type) {
 	case MAXIM_DEVICE_TYPE_MAX77836:
 		supported_regulators = max77836_supported_regulators;
@@ -329,7 +295,7 @@ static int max14577_regulator_probe(struct platform_device *pdev)
 		supported_regulators_size = ARRAY_SIZE(max14577_supported_regulators);
 	}
 
-	config.dev = &pdev->dev;
+	config.dev = max14577->dev;
 	config.driver_data = max14577;
 
 	for (i = 0; i < supported_regulators_size; i++) {

drivers/regulator/max77686.c

@@ -26,6 +26,7 @@
 #include <linux/bug.h>
 #include <linux/err.h>
 #include <linux/gpio.h>
+#include <linux/of_gpio.h>
 #include <linux/slab.h>
 #include <linux/platform_device.h>
 #include <linux/regulator/driver.h>
@@ -45,6 +46,11 @@
 #define MAX77686_DVS_MINUV	600000
 #define MAX77686_DVS_UVSTEP	12500
 
+/*
+ * Value for configuring buck[89] and LDO{20,21,22} as GPIO control.
+ * It is the same as 'off' for other regulators.
+ */
+#define MAX77686_GPIO_CONTROL		0x0
 /*
  * Values used for configuring LDOs and bucks.
  * Forcing low power mode: LDO1, 3-5, 9, 13, 17-26
@@ -82,6 +88,8 @@ enum max77686_ramp_rate {
 };
 
 struct max77686_data {
+	u64 gpio_enabled:MAX77686_REGULATORS;
+
 	/* Array indexed by regulator id */
 	unsigned int opmode[MAX77686_REGULATORS];
 };
@@ -100,6 +108,26 @@ static unsigned int max77686_get_opmode_shift(int id)
 	}
 }
 
+/*
+ * When regulator is configured for GPIO control then it
+ * replaces "normal" mode. Any change from low power mode to normal
+ * should actually change to GPIO control.
+ * Map normal mode to proper value for such regulators.
+ */
+static unsigned int max77686_map_normal_mode(struct max77686_data *max77686,
+					     int id)
+{
+	switch (id) {
+	case MAX77686_BUCK8:
+	case MAX77686_BUCK9:
+	case MAX77686_LDO20 ... MAX77686_LDO22:
+		if (max77686->gpio_enabled & (1 << id))
+			return MAX77686_GPIO_CONTROL;
+	}
+
+	return MAX77686_NORMAL;
+}
+
 /* Some BUCKs and LDOs supports Normal[ON/OFF] mode during suspend */
 static int max77686_set_suspend_disable(struct regulator_dev *rdev)
 {
@@ -136,7 +164,7 @@ static int max77686_set_suspend_mode(struct regulator_dev *rdev,
 		val = MAX77686_LDO_LOWPOWER_PWRREQ;
 		break;
 	case REGULATOR_MODE_NORMAL:			/* ON in Normal Mode */
-		val = MAX77686_NORMAL;
+		val = max77686_map_normal_mode(max77686, id);
 		break;
 	default:
 		pr_warn("%s: regulator_suspend_mode : 0x%x not supported\n",
@@ -160,7 +188,7 @@ static int max77686_ldo_set_suspend_mode(struct regulator_dev *rdev,
 {
 	unsigned int val;
 	struct max77686_data *max77686 = rdev_get_drvdata(rdev);
-	int ret;
+	int ret, id = rdev_get_id(rdev);
 
 	switch (mode) {
 	case REGULATOR_MODE_STANDBY:			/* switch off */
@@ -170,7 +198,7 @@ static int max77686_ldo_set_suspend_mode(struct regulator_dev *rdev,
 		val = MAX77686_LDO_LOWPOWER_PWRREQ;
 		break;
 	case REGULATOR_MODE_NORMAL:			/* ON in Normal Mode */
-		val = MAX77686_NORMAL;
+		val = max77686_map_normal_mode(max77686, id);
 		break;
 	default:
 		pr_warn("%s: regulator_suspend_mode : 0x%x not supported\n",
@@ -184,7 +212,7 @@ static int max77686_ldo_set_suspend_mode(struct regulator_dev *rdev,
 	if (ret)
 		return ret;
 
-	max77686->opmode[rdev_get_id(rdev)] = val;
+	max77686->opmode[id] = val;
 	return 0;
 }
 
@@ -197,7 +225,7 @@ static int max77686_enable(struct regulator_dev *rdev)
 	shift = max77686_get_opmode_shift(id);
 
 	if (max77686->opmode[id] == MAX77686_OFF_PWRREQ)
-		max77686->opmode[id] = MAX77686_NORMAL;
+		max77686->opmode[id] = max77686_map_normal_mode(max77686, id);
 
 	return regmap_update_bits(rdev->regmap, rdev->desc->enable_reg,
 				  rdev->desc->enable_mask,
@@ -229,6 +257,36 @@ static int max77686_set_ramp_delay(struct regulator_dev *rdev, int ramp_delay)
 				  MAX77686_RAMP_RATE_MASK, ramp_value << 6);
 }
 
+static int max77686_of_parse_cb(struct device_node *np,
+		const struct regulator_desc *desc,
+		struct regulator_config *config)
+{
+	struct max77686_data *max77686 = config->driver_data;
+
+	switch (desc->id) {
+	case MAX77686_BUCK8:
+	case MAX77686_BUCK9:
+	case MAX77686_LDO20 ... MAX77686_LDO22:
+		config->ena_gpio = of_get_named_gpio(np,
+					"maxim,ena-gpios", 0);
+		config->ena_gpio_flags = GPIOF_OUT_INIT_HIGH;
+		config->ena_gpio_initialized = true;
+		break;
+	default:
+		return 0;
+	}
+
+	if (gpio_is_valid(config->ena_gpio)) {
+		max77686->gpio_enabled |= (1 << desc->id);
+
+		return regmap_update_bits(config->regmap, desc->enable_reg,
+					  desc->enable_mask,
+					  MAX77686_GPIO_CONTROL);
+	}
+
+	return 0;
+}
+
 static struct regulator_ops max77686_ops = {
 	.list_voltage		= regulator_list_voltage_linear,
 	.map_voltage		= regulator_map_voltage_linear,
@@ -283,6 +341,7 @@ static struct regulator_ops max77686_buck_dvs_ops = {
 	.name		= "LDO"#num,					\
 	.of_match	= of_match_ptr("LDO"#num),			\
 	.regulators_node	= of_match_ptr("voltage-regulators"),	\
+	.of_parse_cb	= max77686_of_parse_cb,				\
 	.id		= MAX77686_LDO##num,				\
 	.ops		= &max77686_ops,				\
 	.type		= REGULATOR_VOLTAGE,				\
@@ -355,6 +414,7 @@ static struct regulator_ops max77686_buck_dvs_ops = {
 	.name		= "BUCK"#num,					\
 	.of_match	= of_match_ptr("BUCK"#num),			\
 	.regulators_node	= of_match_ptr("voltage-regulators"),	\
+	.of_parse_cb	= max77686_of_parse_cb,				\
 	.id		= MAX77686_BUCK##num,				\
 	.ops		= &max77686_ops,				\
 	.type		= REGULATOR_VOLTAGE,				\

drivers/regulator/max77843.c

+/*
+ * max77843.c - Regulator driver for the Maxim MAX77843
+ *
+ * Copyright (C) 2015 Samsung Electronics
+ * Author: Jaewon Kim <jaewon02.kim@samsung.com>
+ * Author: Beomho Seo <beomho.seo@samsung.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/regulator/driver.h>
+#include <linux/regulator/machine.h>
+#include <linux/mfd/max77843-private.h>
+#include <linux/regulator/of_regulator.h>
+
+enum max77843_regulator_type {
+	MAX77843_SAFEOUT1 = 0,
+	MAX77843_SAFEOUT2,
+	MAX77843_CHARGER,
+
+	MAX77843_NUM,
+};
+
+static const unsigned int max77843_safeout_voltage_table[] = {
+	4850000,
+	4900000,
+	4950000,
+	3300000,
+};
+
+static int max77843_reg_is_enabled(struct regulator_dev *rdev)
+{
+	struct regmap *regmap = rdev->regmap;
+	int ret;
+	unsigned int reg;
+
+	ret = regmap_read(regmap, rdev->desc->enable_reg, &reg);
+	if (ret) {
+		dev_err(&rdev->dev, "Fialed to read charger register\n");
+		return ret;
+	}
+
+	return (reg & rdev->desc->enable_mask) == rdev->desc->enable_mask;
+}
+
+static int max77843_reg_get_current_limit(struct regulator_dev *rdev)
+{
+	struct regmap *regmap = rdev->regmap;
+	unsigned int chg_min_uA = rdev->constraints->min_uA;
+	unsigned int chg_max_uA = rdev->constraints->max_uA;
+	unsigned int val;
+	int ret;
+	unsigned int reg, sel;
+
+	ret = regmap_read(regmap, MAX77843_CHG_REG_CHG_CNFG_02, &reg);
+	if (ret) {
+		dev_err(&rdev->dev, "Failed to read charger register\n");
+		return ret;
+	}
+
+	sel = reg & MAX77843_CHG_FAST_CHG_CURRENT_MASK;
+
+	if (sel < 0x03)
+		sel = 0;
+	else
+		sel -= 2;
+
+	val = chg_min_uA + MAX77843_CHG_FAST_CHG_CURRENT_STEP * sel;
+	if (val > chg_max_uA)
+		return -EINVAL;
+
+	return val;
+}
+
+static int max77843_reg_set_current_limit(struct regulator_dev *rdev,
+		int min_uA, int max_uA)
+{
+	struct regmap *regmap = rdev->regmap;
+	unsigned int chg_min_uA = rdev->constraints->min_uA;
+	int sel = 0;
+
+	while (chg_min_uA + MAX77843_CHG_FAST_CHG_CURRENT_STEP * sel < min_uA)
+		sel++;
+
+	if (chg_min_uA + MAX77843_CHG_FAST_CHG_CURRENT_STEP * sel > max_uA)
+		return -EINVAL;
+
+	sel += 2;
+
+	return regmap_write(regmap, MAX77843_CHG_REG_CHG_CNFG_02, sel);
+}
+
+static struct regulator_ops max77843_charger_ops = {
+	.is_enabled		= max77843_reg_is_enabled,
+	.enable			= regulator_enable_regmap,
+	.disable		= regulator_disable_regmap,
+	.get_current_limit	= max77843_reg_get_current_limit,
+	.set_current_limit	= max77843_reg_set_current_limit,
+};
+
+static struct regulator_ops max77843_regulator_ops = {
+	.is_enabled             = regulator_is_enabled_regmap,
+	.enable                 = regulator_enable_regmap,
+	.disable                = regulator_disable_regmap,
+	.list_voltage		= regulator_list_voltage_table,
+	.get_voltage_sel        = regulator_get_voltage_sel_regmap,
+	.set_voltage_sel        = regulator_set_voltage_sel_regmap,
+};
+
+static const struct regulator_desc max77843_supported_regulators[] = {
+	[MAX77843_SAFEOUT1] = {
+		.name		= "SAFEOUT1",
+		.id		= MAX77843_SAFEOUT1,
+		.ops		= &max77843_regulator_ops,
+		.of_match	= of_match_ptr("SAFEOUT1"),
+		.regulators_node = of_match_ptr("regulators"),
+		.type		= REGULATOR_VOLTAGE,
+		.owner		= THIS_MODULE,
+		.n_voltages	= ARRAY_SIZE(max77843_safeout_voltage_table),
+		.volt_table	= max77843_safeout_voltage_table,
+		.enable_reg	= MAX77843_SYS_REG_SAFEOUTCTRL,
+		.enable_mask	= MAX77843_REG_SAFEOUTCTRL_ENSAFEOUT1,
+		.vsel_reg	= MAX77843_SYS_REG_SAFEOUTCTRL,
+		.vsel_mask	= MAX77843_REG_SAFEOUTCTRL_SAFEOUT1_MASK,
+	},
+	[MAX77843_SAFEOUT2] = {
+		.name           = "SAFEOUT2",
+		.id             = MAX77843_SAFEOUT2,
+		.ops            = &max77843_regulator_ops,
+		.of_match	= of_match_ptr("SAFEOUT2"),
+		.regulators_node = of_match_ptr("regulators"),
+		.type           = REGULATOR_VOLTAGE,
+		.owner          = THIS_MODULE,
+		.n_voltages	= ARRAY_SIZE(max77843_safeout_voltage_table),
+		.volt_table	= max77843_safeout_voltage_table,
+		.enable_reg     = MAX77843_SYS_REG_SAFEOUTCTRL,
+		.enable_mask    = MAX77843_REG_SAFEOUTCTRL_ENSAFEOUT2,
+		.vsel_reg	= MAX77843_SYS_REG_SAFEOUTCTRL,
+		.vsel_mask	= MAX77843_REG_SAFEOUTCTRL_SAFEOUT2_MASK,
+	},
+	[MAX77843_CHARGER] = {
+		.name		= "CHARGER",
+		.id		= MAX77843_CHARGER,
+		.ops		= &max77843_charger_ops,
+		.of_match	= of_match_ptr("CHARGER"),
+		.regulators_node = of_match_ptr("regulators"),
+		.type		= REGULATOR_CURRENT,
+		.owner		= THIS_MODULE,
+		.enable_reg	= MAX77843_CHG_REG_CHG_CNFG_00,
+		.enable_mask	= MAX77843_CHG_MASK,
+	},
+};
+
+static struct regmap *max77843_get_regmap(struct max77843 *max77843, int reg_id)
+{
+	switch (reg_id) {
+	case MAX77843_SAFEOUT1:
+	case MAX77843_SAFEOUT2:
+		return max77843->regmap;
+	case MAX77843_CHARGER:
+		return max77843->regmap_chg;
+	default:
+		return max77843->regmap;
+	}
+}
+
+static int max77843_regulator_probe(struct platform_device *pdev)
+{
+	struct max77843 *max77843 = dev_get_drvdata(pdev->dev.parent);
+	struct regulator_config config = {};
+	int i;
+
+	config.dev = max77843->dev;
+	config.driver_data = max77843;
+
+	for (i = 0; i < ARRAY_SIZE(max77843_supported_regulators); i++) {
+		struct regulator_dev *regulator;
+
+		config.regmap = max77843_get_regmap(max77843,
+				max77843_supported_regulators[i].id);
+
+		regulator = devm_regulator_register(&pdev->dev,
+				&max77843_supported_regulators[i], &config);
+		if (IS_ERR(regulator)) {
+			dev_err(&pdev->dev,
+					"Failed to regiser regulator-%d\n", i);
+			return PTR_ERR(regulator);
+		}
+	}
+
+	return 0;
+}
+
+static const struct platform_device_id max77843_regulator_id[] = {
+	{ "max77843-regulator", },
+	{ /* sentinel */ },
+};
+
+static struct platform_driver max77843_regulator_driver = {
+	.driver	= {
+		.name = "max77843-regulator",
+	},
+	.probe		= max77843_regulator_probe,
+	.id_table	= max77843_regulator_id,
+};
+
+static int __init max77843_regulator_init(void)
+{
+	return platform_driver_register(&max77843_regulator_driver);
+}
+subsys_initcall(max77843_regulator_init);
+
+static void __exit max77843_regulator_exit(void)
+{
+	platform_driver_unregister(&max77843_regulator_driver);
+}
+module_exit(max77843_regulator_exit);
+
+MODULE_AUTHOR("Jaewon Kim <jaewon02.kim@samsung.com>");
+MODULE_AUTHOR("Beomho Seo <beomho.seo@samsung.com>");
+MODULE_DESCRIPTION("Maxim MAX77843 regulator driver");
+MODULE_LICENSE("GPL");