Merge branches 'omap-for-v3.13/dt' and 'omap-for-v3.13/quirk' into omap-for-v3.13/board-removal

We need the fixes in v3.12-rc5, dts changes in omap-for-v3.13/dt, and
the platform data quirk changes in omap-for-v3.13/quirk to start
removing omap3 board files without breaking things.

Documentation/devicetree/bindings/crypto/omap-aes.txt

+OMAP SoC AES crypto Module
+
+Required properties:
+
+- compatible : Should contain entries for this and backward compatible
+  AES versions:
+  - "ti,omap2-aes" for OMAP2.
+  - "ti,omap3-aes" for OMAP3.
+  - "ti,omap4-aes" for OMAP4 and AM33XX.
+  Note that the OMAP2 and 3 versions are compatible (OMAP3 supports
+  more algorithms) but they are incompatible with OMAP4.
+- ti,hwmods: Name of the hwmod associated with the AES module
+- reg : Offset and length of the register set for the module
+- interrupts : the interrupt-specifier for the AES module.
+
+Optional properties:
+- dmas: DMA specifiers for tx and rx dma. See the DMA client binding,
+	Documentation/devicetree/bindings/dma/dma.txt
+- dma-names: DMA request names should include "tx" and "rx" if present.
+
+Example:
+	/* AM335x */
+	aes: aes@53500000 {
+		compatible = "ti,omap4-aes";
+		ti,hwmods = "aes";
+		reg = <0x53500000 0xa0>;
+		interrupts = <102>;
+		dmas = <&edma 6>,
+		       <&edma 5>;
+		dma-names = "tx", "rx";
+	};

Documentation/devicetree/bindings/crypto/omap-sham.txt

+OMAP SoC SHA crypto Module
+
+Required properties:
+
+- compatible : Should contain entries for this and backward compatible
+  SHAM versions:
+  - "ti,omap2-sham" for OMAP2 & OMAP3.
+  - "ti,omap4-sham" for OMAP4 and AM33XX.
+  Note that these two versions are incompatible.
+- ti,hwmods: Name of the hwmod associated with the SHAM module
+- reg : Offset and length of the register set for the module
+- interrupts : the interrupt-specifier for the SHAM module.
+
+Optional properties:
+- dmas: DMA specifiers for the rx dma. See the DMA client binding,
+	Documentation/devicetree/bindings/dma/dma.txt
+- dma-names: DMA request name. Should be "rx" if a dma is present.
+
+Example:
+	/* AM335x */
+	sham: sham@53100000 {
+		compatible = "ti,omap4-sham";
+		ti,hwmods = "sham";
+		reg = <0x53100000 0x200>;
+		interrupts = <109>;
+		dmas = <&edma 36>;
+		dma-names = "rx";
+	};

Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt

@@ -20,8 +20,29 @@ ti,dual-volt: boolean, supports dual voltage cards
 ti,non-removable: non-removable slot (like eMMC)
 ti,needs-special-reset: Requires a special softreset sequence
 ti,needs-special-hs-handling: HSMMC IP needs special setting for handling High Speed
+dmas: List of DMA specifiers with the controller specific format
+as described in the generic DMA client binding. A tx and rx
+specifier is required.
+dma-names: List of DMA request names. These strings correspond
+1:1 with the DMA specifiers listed in dmas. The string naming is
+to be "rx" and "tx" for RX and TX DMA requests, respectively.
+
+Examples:
+
+[hwmod populated DMA resources]
+
+	mmc1: mmc@0x4809c000 {
+		compatible = "ti,omap4-hsmmc";
+		reg = <0x4809c000 0x400>;
+		ti,hwmods = "mmc1";
+		ti,dual-volt;
+		bus-width = <4>;
+		vmmc-supply = <&vmmc>; /* phandle to regulator node */
+		ti,non-removable;
+	};
+
+[generic DMA request binding]
 
-Example:
 	mmc1: mmc@0x4809c000 {
 		compatible = "ti,omap4-hsmmc";
 		reg = <0x4809c000 0x400>;
@@ -30,4 +51,7 @@ Example:
 		bus-width = <4>;
 		vmmc-supply = <&vmmc>; /* phandle to regulator node */
 		ti,non-removable;
+		dmas = <&edma 24
+			&edma 25>;
+		dma-names = "tx", "rx";
 	};

Documentation/devicetree/bindings/pinctrl/pinctrl-single.txt

@@ -72,6 +72,13 @@ Optional properties:
 		/* pin base, nr pins & gpio function */
 		pinctrl-single,gpio-range = <&range 0 3 0 &range 3 9 1>;
 
+- interrupt-controller : standard interrupt controller binding if using
+  interrupts for wake-up events for example. In this case pinctrl-single
+  is set up as a chained interrupt controller and the wake-up interrupts
+  can be requested by the drivers using request_irq().
+
+- #interrupt-cells : standard interrupt binding if using interrupts
+
 This driver assumes that there is only one register for each pin (unless the
 pinctrl-single,bit-per-mux is set), and uses the common pinctrl bindings as
 specified in the pinctrl-bindings.txt document in this directory.
@@ -121,6 +128,8 @@ pmx_core: pinmux@4a100040 {
 	reg = <0x4a100040 0x0196>;
 	#address-cells = <1>;
 	#size-cells = <0>;
+	#interrupt-cells = <1>;
+	interrupt-controller;
 	pinctrl-single,register-width = <16>;
 	pinctrl-single,function-mask = <0xffff>;
 };
@@ -131,6 +140,8 @@ pmx_wkup: pinmux@4a31e040 {
 	reg = <0x4a31e040 0x0038>;
 	#address-cells = <1>;
 	#size-cells = <0>;
+	#interrupt-cells = <1>;
+	interrupt-controller;
 	pinctrl-single,register-width = <16>;
 	pinctrl-single,function-mask = <0xffff>;
 };

arch/arm/boot/dts/Makefile

@@ -172,7 +172,9 @@ dtb-$(CONFIG_ARCH_OMAP2PLUS) += omap2420-h4.dtb \
 	omap3-devkit8000.dtb \
 	omap3-beagle-xm.dtb \
 	omap3-evm.dtb \
+	omap3-n900.dtb \
 	omap3-tobi.dtb \
+	omap3-gta04.dtb \
 	omap3-igep0020.dtb \
 	omap3-igep0030.dtb \
 	omap4-panda.dtb \
@@ -186,9 +188,11 @@ dtb-$(CONFIG_ARCH_OMAP2PLUS) += omap2420-h4.dtb \
 	am335x-evmsk.dtb \
 	am335x-bone.dtb \
 	am335x-boneblack.dtb \
+	am335x-base0033.dtb \
 	am3517-evm.dtb \
 	am3517_mt_ventoux.dtb \
-	am43x-epos-evm.dtb
+	am43x-epos-evm.dtb \
+	dra7-evm.dtb
 dtb-$(CONFIG_ARCH_ORION5X) += orion5x-lacie-ethernet-disk-mini-v2.dtb
 dtb-$(CONFIG_ARCH_PRIMA2) += prima2-evb.dtb
 dtb-$(CONFIG_ARCH_U8500) += ste-snowball.dtb \

arch/arm/boot/dts/am335x-base0033.dts

+/*
+ * am335x-base0033.dts - Device Tree file for IGEP AQUILA EXPANSION
+ *
+ * Copyright (C) 2013 ISEE 2007 SL - http://www.isee.biz
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include "am335x-igep0033.dtsi"
+
+/ {
+	model = "IGEP COM AM335x on AQUILA Expansion";
+	compatible = "isee,am335x-base0033", "isee,am335x-igep0033", "ti,am33xx";
+};

arch/arm/boot/dts/am335x-bone-common.dtsi

@@ -21,7 +21,50 @@ memory {
 		reg = <0x80000000 0x10000000>; /* 256 MB */
 	};
 
-	am33xx_pinmux: pinmux@44e10800 {
+	leds {
+		pinctrl-names = "default";
+		pinctrl-0 = <&user_leds_s0>;
+
+		compatible = "gpio-leds";
+
+		led@2 {
+			label = "beaglebone:green:heartbeat";
+			gpios = <&gpio1 21 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+			default-state = "off";
+		};
+
+		led@3 {
+			label = "beaglebone:green:mmc0";
+			gpios = <&gpio1 22 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "mmc0";
+			default-state = "off";
+		};
+
+		led@4 {
+			label = "beaglebone:green:usr2";
+			gpios = <&gpio1 23 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "cpu0";
+			default-state = "off";
+		};
+
+		led@5 {
+			label = "beaglebone:green:usr3";
+			gpios = <&gpio1 24 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "mmc1";
+			default-state = "off";
+		};
+	};
+
+	vmmcsd_fixed: fixedregulator@0 {
+		compatible = "regulator-fixed";
+		regulator-name = "vmmcsd_fixed";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+};
+
+&am33xx_pinmux {
 	pinctrl-names = "default";
 	pinctrl-0 = <&clkout2_pin>;
 
@@ -107,17 +150,37 @@ davinci_mdio_sleep: davinci_mdio_sleep {
 			0x14c (PIN_INPUT_PULLDOWN | MUX_MODE7)
 		>;
 	};
+
+	mmc1_pins: pinmux_mmc1_pins {
+		pinctrl-single,pins = <
+			0x160 (PIN_INPUT | MUX_MODE7) /* GPIO0_6 */
+		>;
 	};
 
-	ocp {
-		uart0: serial@44e09000 {
+	emmc_pins: pinmux_emmc_pins {
+		pinctrl-single,pins = <
+			0x80 (PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_csn1.mmc1_clk */
+			0x84 (PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_csn2.mmc1_cmd */
+			0x00 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad0.mmc1_dat0 */
+			0x04 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad1.mmc1_dat1 */
+			0x08 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad2.mmc1_dat2 */
+			0x0c (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad3.mmc1_dat3 */
+			0x10 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad4.mmc1_dat4 */
+			0x14 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad5.mmc1_dat5 */
+			0x18 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad6.mmc1_dat6 */
+			0x1c (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad7.mmc1_dat7 */
+		>;
+	};
+};
+
+&uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_pins>;
 
 	status = "okay";
-		};
+};
 
-		musb: usb@47400000 {
+&usb {
 	status = "okay";
 
 	control@44e10000 {
@@ -144,9 +207,9 @@ usb@47401800 {
 	dma-controller@07402000  {
 		status = "okay";
 	};
-		};
+};
 
-		i2c0: i2c@44e0b000 {
+&i2c0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&i2c0_pins>;
 
@@ -157,41 +220,6 @@ tps: tps@24 {
 		reg = <0x24>;
 	};
 
-		};
-	};
-
-	leds {
-		pinctrl-names = "default";
-		pinctrl-0 = <&user_leds_s0>;
-
-		compatible = "gpio-leds";
-
-		led@2 {
-			label = "beaglebone:green:heartbeat";
-			gpios = <&gpio1 21 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "heartbeat";
-			default-state = "off";
-		};
-
-		led@3 {
-			label = "beaglebone:green:mmc0";
-			gpios = <&gpio1 22 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "mmc0";
-			default-state = "off";
-		};
-
-		led@4 {
-			label = "beaglebone:green:usr2";
-			gpios = <&gpio1 23 GPIO_ACTIVE_HIGH>;
-			default-state = "off";
-		};
-
-		led@5 {
-			label = "beaglebone:green:usr3";
-			gpios = <&gpio1 24 GPIO_ACTIVE_HIGH>;
-			default-state = "off";
-		};
-	};
 };
 
 /include/ "tps65217.dtsi"
@@ -260,3 +288,12 @@ &davinci_mdio {
 	pinctrl-0 = <&davinci_mdio_default>;
 	pinctrl-1 = <&davinci_mdio_sleep>;
 };
+
+&mmc1 {
+	status = "okay";
+	bus-width = <0x4>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc1_pins>;
+	cd-gpios = <&gpio0 6 GPIO_ACTIVE_HIGH>;
+	cd-inverted;
+};

arch/arm/boot/dts/am335x-bone.dts

@@ -9,3 +9,21 @@
 
 #include "am33xx.dtsi"
 #include "am335x-bone-common.dtsi"
+
+&ldo3_reg {
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-always-on;
+};
+
+&mmc1 {
+	vmmc-supply = <&ldo3_reg>;
+};
+
+&sham {
+	status = "okay";
+};
+
+&aes {
+	status = "okay";
+};

arch/arm/boot/dts/am335x-boneblack.dts

@@ -15,3 +15,64 @@ &ldo3_reg {
 	regulator-max-microvolt = <1800000>;
 	regulator-always-on;
 };
+
+&mmc1 {
+	vmmc-supply = <&vmmcsd_fixed>;
+};
+
+&mmc2 {
+	vmmc-supply = <&vmmcsd_fixed>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&emmc_pins>;
+	bus-width = <8>;
+	status = "okay";
+	ti,vcc-aux-disable-is-sleep;
+};
+
+&am33xx_pinmux {
+	nxp_hdmi_bonelt_pins: nxp_hdmi_bonelt_pins {
+		pinctrl-single,pins = <
+			0x1b0 0x03      /* xdma_event_intr0, OMAP_MUX_MODE3 | AM33XX_PIN_OUTPUT */
+			0xa0 0x08       /* lcd_data0.lcd_data0, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
+			0xa4 0x08       /* lcd_data1.lcd_data1, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
+			0xa8 0x08       /* lcd_data2.lcd_data2, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
+			0xac 0x08       /* lcd_data3.lcd_data3, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
+			0xb0 0x08       /* lcd_data4.lcd_data4, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
+			0xb4 0x08       /* lcd_data5.lcd_data5, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
+			0xb8 0x08       /* lcd_data6.lcd_data6, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
+			0xbc 0x08       /* lcd_data7.lcd_data7, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
+			0xc0 0x08       /* lcd_data8.lcd_data8, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
+			0xc4 0x08       /* lcd_data9.lcd_data9, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
+			0xc8 0x08       /* lcd_data10.lcd_data10, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
+			0xcc 0x08       /* lcd_data11.lcd_data11, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
+			0xd0 0x08       /* lcd_data12.lcd_data12, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
+			0xd4 0x08       /* lcd_data13.lcd_data13, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
+			0xd8 0x08       /* lcd_data14.lcd_data14, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
+			0xdc 0x08       /* lcd_data15.lcd_data15, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
+			0xe0 0x00       /* lcd_vsync.lcd_vsync, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT */
+			0xe4 0x00       /* lcd_hsync.lcd_hsync, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT */
+			0xe8 0x00       /* lcd_pclk.lcd_pclk, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT */
+			0xec 0x00       /* lcd_ac_bias_en.lcd_ac_bias_en, OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT */
+		>;
+	};
+	nxp_hdmi_bonelt_off_pins: nxp_hdmi_bonelt_off_pins {
+		pinctrl-single,pins = <
+			0x1b0 0x03      /* xdma_event_intr0, OMAP_MUX_MODE3 | AM33XX_PIN_OUTPUT */
+		>;
+	};
+};
+
+&lcdc {
+	status = "okay";
+};
+
+/ {
+	hdmi {
+		compatible = "ti,tilcdc,slave";
+		i2c = <&i2c0>;
+		pinctrl-names = "default", "off";
+		pinctrl-0 = <&nxp_hdmi_bonelt_pins>;
+		pinctrl-1 = <&nxp_hdmi_bonelt_off_pins>;
+		status = "okay";
+	};
+};

arch/arm/boot/dts/am335x-evm.dts

@@ -24,7 +24,104 @@ memory {
 		reg = <0x80000000 0x10000000>; /* 256 MB */
 	};
 
-	am33xx_pinmux: pinmux@44e10800 {
+	vbat: fixedregulator@0 {
+		compatible = "regulator-fixed";
+		regulator-name = "vbat";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-boot-on;
+	};
+
+	lis3_reg: fixedregulator@1 {
+		compatible = "regulator-fixed";
+		regulator-name = "lis3_reg";
+		regulator-boot-on;
+	};
+
+	matrix_keypad: matrix_keypad@0 {
+		compatible = "gpio-matrix-keypad";
+		debounce-delay-ms = <5>;
+		col-scan-delay-us = <2>;
+
+		row-gpios = <&gpio1 25 GPIO_ACTIVE_HIGH		/* Bank1, pin25 */
+			     &gpio1 26 GPIO_ACTIVE_HIGH		/* Bank1, pin26 */
+			     &gpio1 27 GPIO_ACTIVE_HIGH>;	/* Bank1, pin27 */
+
+		col-gpios = <&gpio1 21 GPIO_ACTIVE_HIGH		/* Bank1, pin21 */
+			     &gpio1 22 GPIO_ACTIVE_HIGH>;	/* Bank1, pin22 */
+
+		linux,keymap = <0x0000008b	/* MENU */
+				0x0100009e	/* BACK */
+				0x02000069	/* LEFT */
+				0x0001006a	/* RIGHT */
+				0x0101001c	/* ENTER */
+				0x0201006c>;	/* DOWN */
+	};
+
+	gpio_keys: volume_keys@0 {
+		compatible = "gpio-keys";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		autorepeat;
+
+		switch@9 {
+			label = "volume-up";
+			linux,code = <115>;
+			gpios = <&gpio0 2 GPIO_ACTIVE_LOW>;
+			gpio-key,wakeup;
+		};
+
+		switch@10 {
+			label = "volume-down";
+			linux,code = <114>;
+			gpios = <&gpio0 3 GPIO_ACTIVE_LOW>;
+			gpio-key,wakeup;
+		};
+	};
+
+	backlight {
+		compatible = "pwm-backlight";
+		pwms = <&ecap0 0 50000 0>;
+		brightness-levels = <0 51 53 56 62 75 101 152 255>;
+		default-brightness-level = <8>;
+	};
+
+	panel {
+		compatible = "ti,tilcdc,panel";
+		status = "okay";
+		pinctrl-names = "default";
+		pinctrl-0 = <&lcd_pins_s0>;
+		panel-info {
+			ac-bias           = <255>;
+			ac-bias-intrpt    = <0>;
+			dma-burst-sz      = <16>;
+			bpp               = <32>;
+			fdd               = <0x80>;
+			sync-edge         = <0>;
+			sync-ctrl         = <1>;
+			raster-order      = <0>;
+			fifo-th           = <0>;
+		};
+
+		display-timings {
+			800x480p62 {
+				clock-frequency = <30000000>;
+				hactive = <800>;
+				vactive = <480>;
+				hfront-porch = <39>;
+				hback-porch = <39>;
+				hsync-len = <47>;
+				vback-porch = <29>;
+				vfront-porch = <13>;
+				vsync-len = <2>;
+				hsync-active = <1>;
+				vsync-active = <1>;
+			};
+		};
+	};
+};
+
+&am33xx_pinmux {
 	pinctrl-names = "default";
 	pinctrl-0 = <&matrix_keypad_s0 &volume_keys_s0 &clkout2_pin>;
 
@@ -149,17 +246,49 @@ davinci_mdio_sleep: davinci_mdio_sleep {
 			0x14c (PIN_INPUT_PULLDOWN | MUX_MODE7)
 		>;
 	};
+
+	lcd_pins_s0: lcd_pins_s0 {
+		pinctrl-single,pins = <
+			0x20 0x01	/* gpmc_ad8.lcd_data16, OUTPUT | MODE1 */
+			0x24 0x01	/* gpmc_ad9.lcd_data17, OUTPUT | MODE1 */
+			0x28 0x01	/* gpmc_ad10.lcd_data18, OUTPUT | MODE1 */
+			0x2c 0x01	/* gpmc_ad11.lcd_data19, OUTPUT | MODE1 */
+			0x30 0x01	/* gpmc_ad12.lcd_data20, OUTPUT | MODE1 */
+			0x34 0x01	/* gpmc_ad13.lcd_data21, OUTPUT | MODE1 */
+			0x38 0x01	/* gpmc_ad14.lcd_data22, OUTPUT | MODE1 */
+			0x3c 0x01	/* gpmc_ad15.lcd_data23, OUTPUT | MODE1 */
+			0xa0 0x00	/* lcd_data0.lcd_data0, OUTPUT | MODE0 */
+			0xa4 0x00	/* lcd_data1.lcd_data1, OUTPUT | MODE0 */
+			0xa8 0x00	/* lcd_data2.lcd_data2, OUTPUT | MODE0 */
+			0xac 0x00	/* lcd_data3.lcd_data3, OUTPUT | MODE0 */
+			0xb0 0x00	/* lcd_data4.lcd_data4, OUTPUT | MODE0 */
+			0xb4 0x00	/* lcd_data5.lcd_data5, OUTPUT | MODE0 */
+			0xb8 0x00	/* lcd_data6.lcd_data6, OUTPUT | MODE0 */
+			0xbc 0x00	/* lcd_data7.lcd_data7, OUTPUT | MODE0 */
+			0xc0 0x00	/* lcd_data8.lcd_data8, OUTPUT | MODE0 */
+			0xc4 0x00	/* lcd_data9.lcd_data9, OUTPUT | MODE0 */
+			0xc8 0x00	/* lcd_data10.lcd_data10, OUTPUT | MODE0 */
+			0xcc 0x00	/* lcd_data11.lcd_data11, OUTPUT | MODE0 */
+			0xd0 0x00	/* lcd_data12.lcd_data12, OUTPUT | MODE0 */
+			0xd4 0x00	/* lcd_data13.lcd_data13, OUTPUT | MODE0 */
+			0xd8 0x00	/* lcd_data14.lcd_data14, OUTPUT | MODE0 */
+			0xdc 0x00	/* lcd_data15.lcd_data15, OUTPUT | MODE0 */
+			0xe0 0x00	/* lcd_vsync.lcd_vsync, OUTPUT | MODE0 */
+			0xe4 0x00	/* lcd_hsync.lcd_hsync, OUTPUT | MODE0 */
+			0xe8 0x00	/* lcd_pclk.lcd_pclk, OUTPUT | MODE0 */
+			0xec 0x00	/* lcd_ac_bias_en.lcd_ac_bias_en, OUTPUT | MODE0 */
+		>;
 	};
+};
 
-	ocp {
-		uart0: serial@44e09000 {
+&uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_pins>;
 
 	status = "okay";
-		};
+};
 
-		i2c0: i2c@44e0b000 {
+&i2c0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&i2c0_pins>;
 
@@ -169,9 +298,9 @@ i2c0: i2c@44e0b000 {
 	tps: tps@2d {
 		reg = <0x2d>;
 	};
-		};
+};
 
-		musb: usb@47400000 {
+&usb {
 	status = "okay";
 
 	control@44e10000 {
@@ -198,9 +327,9 @@ usb@47401800 {
 	dma-controller@07402000  {
 		status = "okay";
 	};
-		};
+};
 
-		i2c1: i2c@4802a000 {
+&i2c1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&i2c1_pins>;
 
@@ -244,13 +373,17 @@ tmp275: tmp275@48 {
 		compatible = "ti,tmp275";
 		reg = <0x48>;
 	};
-		};
+};
 
-		elm: elm@48080000 {
+&lcdc {
 	status = "okay";
-		};
+};
+
+&elm {
+	status = "okay";
+};
 
-		epwmss0: epwmss@48300000 {
+&epwmss0 {
 	status = "okay";
 
 	ecap0: ecap@48300100 {
@@ -258,9 +391,9 @@ ecap0: ecap@48300100 {
 		pinctrl-names = "default";
 		pinctrl-0 = <&ecap0_pins>;
 	};
-		};
+};
 
-		gpmc: gpmc@50000000 {
+&gpmc {
 	status = "okay";
 	pinctrl-names = "default";
 	pinctrl-0 = <&nandflash_pins_s0>;
@@ -339,70 +472,6 @@ partition@7 {
 			reg = <0x00780000 0x0F880000>;
 		};
 	};
-		};
-	};
-
-	vbat: fixedregulator@0 {
-		compatible = "regulator-fixed";
-		regulator-name = "vbat";
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-		regulator-boot-on;
-	};
-
-	lis3_reg: fixedregulator@1 {
-		compatible = "regulator-fixed";
-		regulator-name = "lis3_reg";
-		regulator-boot-on;
-	};
-
-	matrix_keypad: matrix_keypad@0 {
-		compatible = "gpio-matrix-keypad";
-		debounce-delay-ms = <5>;
-		col-scan-delay-us = <2>;
-
-		row-gpios = <&gpio1 25 GPIO_ACTIVE_HIGH		/* Bank1, pin25 */
-			     &gpio1 26 GPIO_ACTIVE_HIGH		/* Bank1, pin26 */
-			     &gpio1 27 GPIO_ACTIVE_HIGH>;	/* Bank1, pin27 */
-
-		col-gpios = <&gpio1 21 GPIO_ACTIVE_HIGH		/* Bank1, pin21 */
-			     &gpio1 22 GPIO_ACTIVE_HIGH>;	/* Bank1, pin22 */
-
-		linux,keymap = <0x0000008b	/* MENU */
-				0x0100009e	/* BACK */
-				0x02000069	/* LEFT */
-				0x0001006a	/* RIGHT */
-				0x0101001c	/* ENTER */
-				0x0201006c>;	/* DOWN */
-	};
-
-	gpio_keys: volume_keys@0 {
-		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		autorepeat;
-
-		switch@9 {
-			label = "volume-up";
-			linux,code = <115>;
-			gpios = <&gpio0 2 GPIO_ACTIVE_LOW>;
-			gpio-key,wakeup;
-		};
-
-		switch@10 {
-			label = "volume-down";
-			linux,code = <114>;
-			gpios = <&gpio0 3 GPIO_ACTIVE_LOW>;
-			gpio-key,wakeup;
-		};
-	};
-
-	backlight {
-		compatible = "pwm-backlight";
-		pwms = <&ecap0 0 50000 0>;
-		brightness-levels = <0 51 53 56 62 75 101 152 255>;
-		default-brightness-level = <8>;
-	};
 };
 
 #include "tps65910.dtsi"
@@ -477,6 +546,8 @@ vaux33_reg: regulator@11 {
 		};
 
 		vmmc_reg: regulator@12 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <3300000>;
 			regulator-always-on;
 		};
 	};
@@ -517,3 +588,17 @@ adc {
 		ti,adc-channels = <4 5 6 7>;
 	};
 };
+
+&mmc1 {
+	status = "okay";
+	vmmc-supply = <&vmmc_reg>;
+	bus-width = <4>;
+};
+
+&sham {
+	status = "okay";
+};
+
+&aes {
+	status = "okay";
+};

arch/arm/boot/dts/am335x-evmsk.dts

@@ -31,7 +31,93 @@ memory {
 		reg = <0x80000000 0x10000000>; /* 256 MB */
 	};
 
-	am33xx_pinmux: pinmux@44e10800 {
+	vbat: fixedregulator@0 {
+		compatible = "regulator-fixed";
+		regulator-name = "vbat";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-boot-on;
+	};
+
+	lis3_reg: fixedregulator@1 {
+		compatible = "regulator-fixed";
+		regulator-name = "lis3_reg";
+		regulator-boot-on;
+	};
+
+	leds {
+		pinctrl-names = "default";
+		pinctrl-0 = <&user_leds_s0>;
+
+		compatible = "gpio-leds";
+
+		led@1 {
+			label = "evmsk:green:usr0";
+			gpios = <&gpio1 4 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+
+		led@2 {
+			label = "evmsk:green:usr1";
+			gpios = <&gpio1 5 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+
+		led@3 {
+			label = "evmsk:green:mmc0";
+			gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "mmc0";
+			default-state = "off";
+		};
+
+		led@4 {
+			label = "evmsk:green:heartbeat";
+			gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+			default-state = "off";
+		};
+	};
+
+	gpio_buttons: gpio_buttons@0 {
+		compatible = "gpio-keys";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		switch@1 {
+			label = "button0";
+			linux,code = <0x100>;
+			gpios = <&gpio2 3 GPIO_ACTIVE_HIGH>;
+		};
+
+		switch@2 {
+			label = "button1";
+			linux,code = <0x101>;
+			gpios = <&gpio2 2 GPIO_ACTIVE_HIGH>;
+		};
+
+		switch@3 {
+			label = "button2";
+			linux,code = <0x102>;
+			gpios = <&gpio0 30 GPIO_ACTIVE_HIGH>;
+			gpio-key,wakeup;
+		};
+
+		switch@4 {
+			label = "button3";
+			linux,code = <0x103>;
+			gpios = <&gpio2 5 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	backlight {
+		compatible = "pwm-backlight";
+		pwms = <&ecap2 0 50000 PWM_POLARITY_INVERTED>;
+		brightness-levels = <0 58 61 66 75 90 125 170 255>;
+		default-brightness-level = <8>;
+	};
+};
+
+&am33xx_pinmux {
 	pinctrl-names = "default";
 	pinctrl-0 = <&gpio_keys_s0 &clkout2_pin>;
 
@@ -158,17 +244,16 @@ davinci_mdio_sleep: davinci_mdio_sleep {
 			0x14c (PIN_INPUT_PULLDOWN | MUX_MODE7)
 		>;
 	};
-	};
+};
 
-	ocp {
-		uart0: serial@44e09000 {
+&uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_pins>;
 
 	status = "okay";
-		};
+};
 
-		i2c0: i2c@44e0b000 {
+&i2c0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&i2c0_pins>;
 
@@ -206,9 +291,9 @@ lis331dlh: lis331dlh@18 {
 		st,max-limit-y = <550>;
 		st,max-limit-z = <750>;
 	};
-		};
+};
 
-		musb: usb@47400000 {
+&usb {
 	status = "okay";
 
 	control@44e10000 {
@@ -222,9 +307,9 @@ usb-phy@47401300 {
 	usb@47401000 {
 		status = "okay";
 	};
-		};
+};
 
-		epwmss2: epwmss@48304000 {
+&epwmss2 {
 	status = "okay";
 
 	ecap2: ecap@48304100 {
@@ -232,93 +317,6 @@ ecap2: ecap@48304100 {
 		pinctrl-names = "default";
 		pinctrl-0 = <&ecap2_pins>;
 	};
-		};
-	};
-
-	vbat: fixedregulator@0 {
-		compatible = "regulator-fixed";
-		regulator-name = "vbat";
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-		regulator-boot-on;
-	};
-
-	lis3_reg: fixedregulator@1 {
-		compatible = "regulator-fixed";
-		regulator-name = "lis3_reg";
-		regulator-boot-on;
-	};
-
-	leds {
-		pinctrl-names = "default";
-		pinctrl-0 = <&user_leds_s0>;
-
-		compatible = "gpio-leds";
-
-		led@1 {
-			label = "evmsk:green:usr0";
-			gpios = <&gpio1 4 GPIO_ACTIVE_HIGH>;
-			default-state = "off";
-		};
-
-		led@2 {
-			label = "evmsk:green:usr1";
-			gpios = <&gpio1 5 GPIO_ACTIVE_HIGH>;
-			default-state = "off";
-		};
-
-		led@3 {
-			label = "evmsk:green:mmc0";
-			gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "mmc0";
-			default-state = "off";
-		};
-
-		led@4 {
-			label = "evmsk:green:heartbeat";
-			gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "heartbeat";
-			default-state = "off";
-		};
-	};
-
-	gpio_buttons: gpio_buttons@0 {
-		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		switch@1 {
-			label = "button0";
-			linux,code = <0x100>;
-			gpios = <&gpio2 3 GPIO_ACTIVE_HIGH>;
-		};
-
-		switch@2 {
-			label = "button1";
-			linux,code = <0x101>;
-			gpios = <&gpio2 2 GPIO_ACTIVE_HIGH>;
-		};
-
-		switch@3 {
-			label = "button2";
-			linux,code = <0x102>;
-			gpios = <&gpio0 30 GPIO_ACTIVE_HIGH>;
-			gpio-key,wakeup;
-		};
-
-		switch@4 {
-			label = "button3";
-			linux,code = <0x103>;
-			gpios = <&gpio2 5 GPIO_ACTIVE_HIGH>;
-		};
-	};
-
-	backlight {
-		compatible = "pwm-backlight";
-		pwms = <&ecap2 0 50000 PWM_POLARITY_INVERTED>;
-		brightness-levels = <0 58 61 66 75 90 125 170 255>;
-		default-brightness-level = <8>;
-	};
 };
 
 #include "tps65910.dtsi"
@@ -393,6 +391,8 @@ vaux33_reg: regulator@11 {
 		};
 
 		vmmc_reg: regulator@12 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <3300000>;
 			regulator-always-on;
 		};
 	};
@@ -419,3 +419,17 @@ &cpsw_emac1 {
 	phy_id = <&davinci_mdio>, <1>;
 	phy-mode = "rgmii-txid";
 };
+
+&mmc1 {
+	status = "okay";
+	vmmc-supply = <&vmmc_reg>;
+	bus-width = <4>;
+};
+
+&sham {
+	status = "okay";
+};
+
+&aes {
+	status = "okay";
+};

arch/arm/boot/dts/am335x-igep0033.dtsi

+/*
+ * am335x-igep0033.dtsi - Device Tree file for IGEP COM AQUILA AM335x
+ *
+ * Copyright (C) 2013 ISEE 2007 SL - http://www.isee.biz
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/dts-v1/;
+
+#include "am33xx.dtsi"
+
+/ {
+	cpus {
+		cpu@0 {
+			cpu0-supply = <&vdd1_reg>;
+		};
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0x80000000 0x10000000>; /* 256 MB */
+	};
+
+	leds {
+		pinctrl-names = "default";
+		pinctrl-0 = <&leds_pins>;
+
+		compatible = "gpio-leds";
+
+		led@0 {
+			label = "com:green:user";
+			gpios = <&gpio1 23 GPIO_ACTIVE_HIGH>;
+			default-state = "on";
+		};
+	};
+
+	vbat: fixedregulator@0 {
+		compatible = "regulator-fixed";
+		regulator-name = "vbat";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-boot-on;
+	};
+};
+
+&am33xx_pinmux {
+	i2c0_pins: pinmux_i2c0_pins {
+		pinctrl-single,pins = <
+			0x188 (PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c0_sda.i2c0_sda */
+			0x18c (PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c0_scl.i2c0_scl */
+		>;
+	};
+
+	nandflash_pins: pinmux_nandflash_pins {
+		pinctrl-single,pins = <
+			0x0 (PIN_INPUT_PULLUP | MUX_MODE0)	/* gpmc_ad0.gpmc_ad0 */
+			0x4 (PIN_INPUT_PULLUP | MUX_MODE0)	/* gpmc_ad1.gpmc_ad1 */
+			0x8 (PIN_INPUT_PULLUP | MUX_MODE0)	/* gpmc_ad2.gpmc_ad2 */
+			0xc (PIN_INPUT_PULLUP | MUX_MODE0)	/* gpmc_ad3.gpmc_ad3 */
+			0x10 (PIN_INPUT_PULLUP | MUX_MODE0)	/* gpmc_ad4.gpmc_ad4 */
+			0x14 (PIN_INPUT_PULLUP | MUX_MODE0)	/* gpmc_ad5.gpmc_ad5 */
+			0x18 (PIN_INPUT_PULLUP | MUX_MODE0)	/* gpmc_ad6.gpmc_ad6 */
+			0x1c (PIN_INPUT_PULLUP | MUX_MODE0)	/* gpmc_ad7.gpmc_ad7 */
+			0x70 (PIN_INPUT_PULLUP | MUX_MODE0)	/* gpmc_wait0.gpmc_wait0 */
+			0x74 (PIN_INPUT_PULLUP | MUX_MODE7)	/* gpmc_wpn.gpio0_30 */
+			0x7c (PIN_OUTPUT | MUX_MODE0)		/* gpmc_csn0.gpmc_csn0 */
+			0x90 (PIN_OUTPUT | MUX_MODE0)		/* gpmc_advn_ale.gpmc_advn_ale */
+			0x94 (PIN_OUTPUT | MUX_MODE0)		/* gpmc_oen_ren.gpmc_oen_ren */
+			0x98 (PIN_OUTPUT | MUX_MODE0)		/* gpmc_wen.gpmc_wen */
+			0x9c (PIN_OUTPUT | MUX_MODE0)		/* gpmc_be0n_cle.gpmc_be0n_cle */
+		>;
+	};
+
+	uart0_pins: pinmux_uart0_pins {
+		pinctrl-single,pins = <
+			0x170 (PIN_INPUT_PULLUP | MUX_MODE0)	/* uart0_rxd.uart0_rxd */
+			0x174 (PIN_OUTPUT_PULLDOWN | MUX_MODE0)	/* uart0_txd.uart0_txd */
+		>;
+	};
+
+	leds_pins: pinmux_leds_pins {
+		pinctrl-single,pins = <
+			0x5c (PIN_OUTPUT_PULLDOWN | MUX_MODE7)	/* gpmc_a7.gpio1_23 */
+		>;
+	};
+};
+
+&cpsw_emac0 {
+	phy_id = <&davinci_mdio>, <0>;
+};
+
+&cpsw_emac1 {
+	phy_id = <&davinci_mdio>, <1>;
+};
+
+&elm {
+	status = "okay";
+};
+
+&gpmc {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&nandflash_pins>;
+
+	ranges = <0 0 0x08000000 0x10000000>;	/* CS0: NAND */
+
+	nand@0,0 {
+		reg = <0 0 0>; /* CS0, offset 0 */
+		nand-bus-width = <8>;
+		ti,nand-ecc-opt = "bch8";
+		gpmc,device-nand = "true";
+		gpmc,device-width = <1>;
+		gpmc,sync-clk-ps = <0>;
+		gpmc,cs-on-ns = <0>;
+		gpmc,cs-rd-off-ns = <44>;
+		gpmc,cs-wr-off-ns = <44>;
+		gpmc,adv-on-ns = <6>;
+		gpmc,adv-rd-off-ns = <34>;
+		gpmc,adv-wr-off-ns = <44>;
+		gpmc,we-on-ns = <0>;
+		gpmc,we-off-ns = <40>;
+		gpmc,oe-on-ns = <0>;
+		gpmc,oe-off-ns = <54>;
+		gpmc,access-ns = <64>;
+		gpmc,rd-cycle-ns = <82>;
+		gpmc,wr-cycle-ns = <82>;
+		gpmc,wait-on-read = "true";
+		gpmc,wait-on-write = "true";
+		gpmc,bus-turnaround-ns = <0>;
+		gpmc,cycle2cycle-delay-ns = <0>;
+		gpmc,clk-activation-ns = <0>;
+		gpmc,wait-monitoring-ns = <0>;
+		gpmc,wr-access-ns = <40>;
+		gpmc,wr-data-mux-bus-ns = <0>;
+
+		#address-cells = <1>;
+		#size-cells = <1>;
+		elm_id = <&elm>;
+
+		/* MTD partition table */
+		partition@0 {
+			label = "SPL";
+			reg = <0x00000000 0x000080000>;
+		};
+
+		partition@1 {
+			label = "U-boot";
+			reg = <0x00080000 0x001e0000>;
+		};
+
+		partition@2 {
+			label = "U-Boot Env";
+			reg = <0x00260000 0x00020000>;
+		};
+
+		partition@3 {
+			label = "Kernel";
+			reg = <0x00280000 0x00500000>;
+		};
+
+		partition@4 {
+			label = "File System";
+			reg = <0x00780000 0x007880000>;
+		};
+	};
+};
+
+&i2c0 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins>;
+
+	clock-frequency = <400000>;
+
+	tps: tps@2d {
+		reg = <0x2d>;
+	};
+};
+
+&uart0 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pins>;
+};
+
+#include "tps65910.dtsi"
+
+&tps {
+	vcc1-supply = <&vbat>;
+	vcc2-supply = <&vbat>;
+	vcc3-supply = <&vbat>;
+	vcc4-supply = <&vbat>;
+	vcc5-supply = <&vbat>;
+	vcc6-supply = <&vbat>;
+	vcc7-supply = <&vbat>;
+	vccio-supply = <&vbat>;
+
+	regulators {
+		vrtc_reg: regulator@0 {
+			regulator-always-on;
+		};
+
+		vio_reg: regulator@1 {
+			regulator-always-on;
+		};
+
+		vdd1_reg: regulator@2 {
+			/* VDD_MPU voltage limits 0.95V - 1.26V with +/-4% tolerance */
+			regulator-name = "vdd_mpu";
+			regulator-min-microvolt = <912500>;
+			regulator-max-microvolt = <1312500>;
+			regulator-boot-on;
+			regulator-always-on;
+		};
+
+		vdd2_reg: regulator@3 {
+			/* VDD_CORE voltage limits 0.95V - 1.1V with +/-4% tolerance */
+			regulator-name = "vdd_core";
+			regulator-min-microvolt = <912500>;
+			regulator-max-microvolt = <1150000>;
+			regulator-boot-on;
+			regulator-always-on;
+		};
+
+		vdd3_reg: regulator@4 {
+			regulator-always-on;
+		};
+
+		vdig1_reg: regulator@5 {
+			regulator-always-on;
+		};
+
+		vdig2_reg: regulator@6 {
+			regulator-always-on;
+		};
+
+		vpll_reg: regulator@7 {
+			regulator-always-on;
+		};
+
+		vdac_reg: regulator@8 {
+			regulator-always-on;
+		};
+
+		vaux1_reg: regulator@9 {
+			regulator-always-on;
+		};
+
+		vaux2_reg: regulator@10 {
+			regulator-always-on;
+		};
+
+		vaux33_reg: regulator@11 {
+			regulator-always-on;
+		};
+
+		vmmc_reg: regulator@12 {
+			regulator-always-on;
+		};
+	};
+};
+

arch/arm/boot/dts/am33xx.dtsi

@@ -30,6 +30,8 @@ aliases {
 		usb1 = &usb1;
 		phy0 = &usb0_phy;
 		phy1 = &usb1_phy;
+		ethernet0 = &cpsw_emac0;
+		ethernet1 = &cpsw_emac1;
 	};
 
 	cpus {
@@ -57,6 +59,11 @@ cpu@0 {
 		};
 	};
 
+	pmu {
+		compatible = "arm,cortex-a8-pmu";
+		interrupts = <3>;
+	};
+
 	/*
 	 * The soc node represents the soc top level view. It is uses for IPs
 	 * that are not memory mapped in the MPU view or for the MPU itself.
@@ -100,13 +107,25 @@ intc: interrupt-controller@48200000 {
 			reg = <0x48200000 0x1000>;
 		};
 
+		edma: edma@49000000 {
+			compatible = "ti,edma3";
+			ti,hwmods = "tpcc", "tptc0", "tptc1", "tptc2";
+			reg =	<0x49000000 0x10000>,
+				<0x44e10f90 0x10>;
+			interrupts = <12 13 14>;
+			#dma-cells = <1>;
+			dma-channels = <64>;
+			ti,edma-regions = <4>;
+			ti,edma-slots = <256>;
+		};
+
 		gpio0: gpio@44e07000 {
 			compatible = "ti,omap4-gpio";
 			ti,hwmods = "gpio1";
 			gpio-controller;
 			#gpio-cells = <2>;
 			interrupt-controller;
-			#interrupt-cells = <1>;
+			#interrupt-cells = <2>;
 			reg = <0x44e07000 0x1000>;
 			interrupts = <96>;
 		};
@@ -117,7 +136,7 @@ gpio1: gpio@4804c000 {
 			gpio-controller;
 			#gpio-cells = <2>;
 			interrupt-controller;
-			#interrupt-cells = <1>;
+			#interrupt-cells = <2>;
 			reg = <0x4804c000 0x1000>;
 			interrupts = <98>;
 		};
@@ -128,7 +147,7 @@ gpio2: gpio@481ac000 {
 			gpio-controller;
 			#gpio-cells = <2>;
 			interrupt-controller;
-			#interrupt-cells = <1>;
+			#interrupt-cells = <2>;
 			reg = <0x481ac000 0x1000>;
 			interrupts = <32>;
 		};
@@ -139,7 +158,7 @@ gpio3: gpio@481ae000 {
 			gpio-controller;
 			#gpio-cells = <2>;
 			interrupt-controller;
-			#interrupt-cells = <1>;
+			#interrupt-cells = <2>;
 			reg = <0x481ae000 0x1000>;
 			interrupts = <62>;
 		};
@@ -228,6 +247,44 @@ i2c2: i2c@4819c000 {
 			status = "disabled";
 		};
 
+		mmc1: mmc@48060000 {
+			compatible = "ti,omap4-hsmmc";
+			ti,hwmods = "mmc1";
+			ti,dual-volt;
+			ti,needs-special-reset;
+			ti,needs-special-hs-handling;
+			dmas = <&edma 24
+				&edma 25>;
+			dma-names = "tx", "rx";
+			interrupts = <64>;
+			interrupt-parent = <&intc>;
+			reg = <0x48060000 0x1000>;
+			status = "disabled";
+		};
+
+		mmc2: mmc@481d8000 {
+			compatible = "ti,omap4-hsmmc";
+			ti,hwmods = "mmc2";
+			ti,needs-special-reset;
+			dmas = <&edma 2
+				&edma 3>;
+			dma-names = "tx", "rx";
+			interrupts = <28>;
+			interrupt-parent = <&intc>;
+			reg = <0x481d8000 0x1000>;
+			status = "disabled";
+		};
+
+		mmc3: mmc@47810000 {
+			compatible = "ti,omap4-hsmmc";
+			ti,hwmods = "mmc3";
+			ti,needs-special-reset;
+			interrupts = <29>;
+			interrupt-parent = <&intc>;
+			reg = <0x47810000 0x1000>;
+			status = "disabled";
+		};
+
 		wdt2: wdt@44e35000 {
 			compatible = "ti,omap3-wdt";
 			ti,hwmods = "wd_timer2";
@@ -323,6 +380,11 @@ spi0: spi@48030000 {
 			interrupts = <65>;
 			ti,spi-num-cs = <2>;
 			ti,hwmods = "spi0";
+			dmas = <&edma 16
+				&edma 17
+				&edma 18
+				&edma 19>;
+			dma-names = "tx0", "rx0", "tx1", "rx1";
 			status = "disabled";
 		};
 
@@ -334,6 +396,11 @@ spi1: spi@481a0000 {
 			interrupts = <125>;
 			ti,spi-num-cs = <2>;
 			ti,hwmods = "spi1";
+			dmas = <&edma 42
+				&edma 43
+				&edma 44
+				&edma 45>;
+			dma-names = "tx0", "rx0", "tx1", "rx1";
 			status = "disabled";
 		};
 
@@ -617,6 +684,15 @@ elm: elm@48080000 {
 			status = "disabled";
 		};
 
+		lcdc: lcdc@4830e000 {
+			compatible = "ti,am33xx-tilcdc";
+			reg = <0x4830e000 0x1000>;
+			interrupt-parent = <&intc>;
+			interrupts = <36>;
+			ti,hwmods = "lcdc";
+			status = "disabled";
+		};
+
 		tscadc: tscadc@44e0d000 {
 			compatible = "ti,am3359-tscadc";
 			reg = <0x44e0d000 0x1000>;
@@ -645,5 +721,24 @@ gpmc: gpmc@50000000 {
 			#size-cells = <1>;
 			status = "disabled";
 		};
+
+		sham: sham@53100000 {
+			compatible = "ti,omap4-sham";
+			ti,hwmods = "sham";
+			reg = <0x53100000 0x200>;
+			interrupts = <109>;
+			dmas = <&edma 36>;
+			dma-names = "rx";
+		};
+
+		aes: aes@53500000 {
+			compatible = "ti,omap4-aes";
+			ti,hwmods = "aes";
+			reg = <0x53500000 0xa0>;
+			interrupts = <103>;
+			dmas = <&edma 6>,
+			       <&edma 5>;
+			dma-names = "tx", "rx";
+		};
 	};
 };

arch/arm/boot/dts/dra7-evm.dts

+/*
+ * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+/dts-v1/;
+
+#include "dra7.dtsi"
+
+/ {
+	model = "TI DRA7";
+	compatible = "ti,dra7-evm", "ti,dra752", "ti,dra7";
+
+	memory {
+		device_type = "memory";
+		reg = <0x80000000 0x60000000>; /* 1536 MB */
+	};
+
+	mmc2_3v3: fixedregulator-mmc2 {
+		compatible = "regulator-fixed";
+		regulator-name = "mmc2_3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+};
+
+&dra7_pmx_core {
+	i2c1_pins: pinmux_i2c1_pins {
+		pinctrl-single,pins = <
+			0x400 (PIN_INPUT | MUX_MODE0) /* i2c1_sda */
+			0x404 (PIN_INPUT | MUX_MODE0) /* i2c1_scl */
+		>;
+	};
+
+	i2c2_pins: pinmux_i2c2_pins {
+		pinctrl-single,pins = <
+			0x408 (PIN_INPUT | MUX_MODE0) /* i2c2_sda */
+			0x40c (PIN_INPUT | MUX_MODE0) /* i2c2_scl */
+		>;
+	};
+
+	i2c3_pins: pinmux_i2c3_pins {
+		pinctrl-single,pins = <
+			0x410 (PIN_INPUT | MUX_MODE0) /* i2c3_sda */
+			0x414 (PIN_INPUT | MUX_MODE0) /* i2c3_scl */
+		>;
+	};
+
+	mcspi1_pins: pinmux_mcspi1_pins {
+		pinctrl-single,pins = <
+			0x3a4 (PIN_INPUT | MUX_MODE0) /* spi2_clk */
+			0x3a8 (PIN_INPUT | MUX_MODE0) /* spi2_d1 */
+			0x3ac (PIN_INPUT | MUX_MODE0) /* spi2_d0 */
+			0x3b0 (PIN_INPUT_SLEW | MUX_MODE0) /* spi2_cs0 */
+			0x3b4 (PIN_INPUT_SLEW | MUX_MODE0) /* spi2_cs1 */
+			0x3b8 (PIN_INPUT_SLEW | MUX_MODE6) /* spi2_cs2 */
+			0x3bc (PIN_INPUT_SLEW | MUX_MODE6) /* spi2_cs3 */
+		>;
+	};
+
+	mcspi2_pins: pinmux_mcspi2_pins {
+		pinctrl-single,pins = <
+			0x3c0 (PIN_INPUT | MUX_MODE0) /* spi2_sclk */
+			0x3c4 (PIN_INPUT_SLEW | MUX_MODE0) /* spi2_d1 */
+			0x3c8 (PIN_INPUT_SLEW | MUX_MODE0) /* spi2_d1 */
+			0x3cc (PIN_INPUT_SLEW | MUX_MODE0) /* spi2_cs0 */
+		>;
+	};
+
+	uart1_pins: pinmux_uart1_pins {
+		pinctrl-single,pins = <
+			0x3e0 (PIN_INPUT_SLEW | MUX_MODE0) /* uart1_rxd */
+			0x3e4 (PIN_INPUT_SLEW | MUX_MODE0) /* uart1_txd */
+			0x3e8 (PIN_INPUT | MUX_MODE3) /* uart1_ctsn */
+			0x3ec (PIN_INPUT | MUX_MODE3) /* uart1_rtsn */
+		>;
+	};
+
+	uart2_pins: pinmux_uart2_pins {
+		pinctrl-single,pins = <
+			0x3f0 (PIN_INPUT | MUX_MODE0) /* uart2_rxd */
+			0x3f4 (PIN_INPUT | MUX_MODE0) /* uart2_txd */
+			0x3f8 (PIN_INPUT | MUX_MODE0) /* uart2_ctsn */
+			0x3fc (PIN_INPUT | MUX_MODE0) /* uart2_rtsn */
+		>;
+	};
+
+	uart3_pins: pinmux_uart3_pins {
+		pinctrl-single,pins = <
+			0x248 (PIN_INPUT_SLEW | MUX_MODE0) /* uart3_rxd */
+			0x24c (PIN_INPUT_SLEW | MUX_MODE0) /* uart3_txd */
+		>;
+	};
+};
+
+&i2c1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins>;
+	clock-frequency = <400000>;
+
+	tps659038: tps659038@58 {
+		compatible = "ti,tps659038";
+		reg = <0x58>;
+
+		tps659038_pmic {
+			compatible = "ti,tps659038-pmic";
+
+			regulators {
+				smps123_reg: smps123 {
+					/* VDD_MPU */
+					regulator-name = "smps123";
+					regulator-min-microvolt = < 850000>;
+					regulator-max-microvolt = <1250000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				smps45_reg: smps45 {
+					/* VDD_DSPEVE */
+					regulator-name = "smps45";
+					regulator-min-microvolt = < 850000>;
+					regulator-max-microvolt = <1150000>;
+					regulator-boot-on;
+				};
+
+				smps6_reg: smps6 {
+					/* VDD_GPU - over VDD_SMPS6 */
+					regulator-name = "smps6";
+					regulator-min-microvolt = <850000>;
+					regulator-max-microvolt = <12500000>;
+					regulator-boot-on;
+				};
+
+				smps7_reg: smps7 {
+					/* CORE_VDD */
+					regulator-name = "smps7";
+					regulator-min-microvolt = <850000>;
+					regulator-max-microvolt = <1030000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				smps8_reg: smps8 {
+					/* VDD_IVAHD */
+					regulator-name = "smps8";
+					regulator-min-microvolt = < 850000>;
+					regulator-max-microvolt = <1250000>;
+					regulator-boot-on;
+				};
+
+				smps9_reg: smps9 {
+					/* VDDS1V8 */
+					regulator-name = "smps9";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				ldo1_reg: ldo1 {
+					/* LDO1_OUT --> SDIO  */
+					regulator-name = "ldo1";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <3300000>;
+					regulator-boot-on;
+				};
+
+				ldo2_reg: ldo2 {
+					/* VDD_RTCIO */
+					/* LDO2 -> VDDSHV5, LDO2 also goes to CAN_PHY_3V3 */
+					regulator-name = "ldo2";
+					regulator-min-microvolt = <3300000>;
+					regulator-max-microvolt = <3300000>;
+					regulator-boot-on;
+				};
+
+				ldo3_reg: ldo3 {
+					/* VDDA_1V8_PHY */
+					regulator-name = "ldo3";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					regulator-boot-on;
+				};
+
+				ldo9_reg: ldo9 {
+					/* VDD_RTC */
+					regulator-name = "ldo9";
+					regulator-min-microvolt = <1050000>;
+					regulator-max-microvolt = <1050000>;
+					regulator-boot-on;
+				};
+
+				ldoln_reg: ldoln {
+					/* VDDA_1V8_PLL */
+					regulator-name = "ldoln";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				ldousb_reg: ldousb {
+					/* VDDA_3V_USB: VDDA_USBHS33 */
+					regulator-name = "ldousb";
+					regulator-min-microvolt = <3300000>;
+					regulator-max-microvolt = <3300000>;
+					regulator-boot-on;
+				};
+			};
+		};
+	};
+};
+
+&i2c2 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c2_pins>;
+	clock-frequency = <400000>;
+};
+
+&i2c3 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c3_pins>;
+	clock-frequency = <3400000>;
+};
+
+&mcspi1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mcspi1_pins>;
+};
+
+&mcspi2 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mcspi2_pins>;
+};
+
+&uart1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_pins>;
+};
+
+&uart2 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart2_pins>;
+};
+
+&uart3 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart3_pins>;
+};
+
+&mmc1 {
+	status = "okay";
+	vmmc-supply = <&ldo1_reg>;
+	bus-width = <4>;
+};
+
+&mmc2 {
+	status = "okay";
+	vmmc-supply = <&mmc2_3v3>;
+	bus-width = <8>;
+};

arch/arm/boot/dts/omap2420-h4.dts

@@ -50,15 +50,15 @@ partition@0 {
 			label = "bootloader";
 			reg = <0 0x20000>;
 		};
-		partition@0x20000 {
+		partition@20000 {
 			label = "params";
 			reg = <0x20000 0x20000>;
 		};
-		partition@0x40000 {
+		partition@40000 {
 			label = "kernel";
 			reg = <0x40000 0x200000>;
 		};
-		partition@0x240000 {
+		partition@240000 {
 			label = "file-system";
 			reg = <0x240000 0x3dc0000>;
 		};

arch/arm/boot/dts/omap3-beagle-xm.dts

@@ -69,6 +69,23 @@ user {
 		};
 
 	};
+
+	/* HS USB Port 2 Power */
+	hsusb2_power: hsusb2_power_reg {
+		compatible = "regulator-fixed";
+		regulator-name = "hsusb2_vbus";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&twl_gpio 18 0>;	/* GPIO LEDA */
+		startup-delay-us = <70000>;
+	};
+
+	/* HS USB Host PHY on PORT 2 */
+	hsusb2_phy: hsusb2_phy {
+		compatible = "usb-nop-xceiv";
+		reset-gpios = <&gpio5 19 GPIO_ACTIVE_LOW>; /* gpio_147 */
+		vcc-supply = <&hsusb2_power>;
+	};
 };
 
 &omap3_pmx_wkup {
@@ -79,6 +96,37 @@ gpio1_pins: pinmux_gpio1_pins {
 	};
 };
 
+&omap3_pmx_core {
+	pinctrl-names = "default";
+	pinctrl-0 = <
+			&hsusbb2_pins
+	>;
+
+	uart3_pins: pinmux_uart3_pins {
+		pinctrl-single,pins = <
+			0x16e (PIN_INPUT | PIN_OFF_WAKEUPENABLE | MUX_MODE0) /* uart3_rx_irrx.uart3_rx_irrx */
+			0x170 (PIN_OUTPUT | MUX_MODE0) /* uart3_tx_irtx.uart3_tx_irtx OUTPUT | MODE0 */
+		>;
+	};
+
+	hsusbb2_pins: pinmux_hsusbb2_pins {
+		pinctrl-single,pins = <
+			0x5c0 (PIN_OUTPUT | MUX_MODE3)		/* etk_d10.hsusb2_clk */
+			0x5c2 (PIN_OUTPUT | MUX_MODE3)		/* etk_d11.hsusb2_stp */
+			0x5c4 (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* etk_d12.hsusb2_dir */
+			0x5c6 (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* etk_d13.hsusb2_nxt */
+			0x5c8 (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* etk_d14.hsusb2_data0 */
+			0x5cA (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* etk_d15.hsusb2_data1 */
+			0x1a4 (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* mcspi1_cs3.hsusb2_data2 */
+			0x1a6 (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* mcspi2_clk.hsusb2_data7 */
+			0x1a8 (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* mcspi2_simo.hsusb2_data4 */
+			0x1aa (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* mcspi2_somi.hsusb2_data5 */
+			0x1ac (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* mcspi2_cs0.hsusb2_data6 */
+			0x1ae (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* mcspi2_cs1.hsusb2_data3 */
+		>;
+	};
+};
+
 &i2c1 {
 	clock-frequency = <2600000>;
 
@@ -148,15 +196,6 @@ &usb_otg_hs {
 	power = <50>;
 };
 
-&omap3_pmx_core {
-	uart3_pins: pinmux_uart3_pins {
-		pinctrl-single,pins = <
-			0x16e (PIN_INPUT | PIN_OFF_WAKEUPENABLE | MUX_MODE0) /* uart3_rx_irrx.uart3_rx_irrx */
-			0x170 (PIN_OUTPUT | MUX_MODE0) /* uart3_tx_irtx.uart3_tx_irtx OUTPUT | MODE0 */
-		>;
-	};
-};
-
 &uart3 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart3_pins>;
@@ -166,3 +205,11 @@ &gpio1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&gpio1_pins>;
 };
+
+&usbhshost {
+	port2-mode = "ehci-phy";
+};
+
+&usbhsehci {
+	phys = <0 &hsusb2_phy>;
+};

arch/arm/boot/dts/omap3-beagle.dts

@@ -44,17 +44,6 @@ mmc {
 		};
 	};
 
-	/* HS USB Port 2 RESET */
-	hsusb2_reset: hsusb2_reset_reg {
-		compatible = "regulator-fixed";
-		regulator-name = "hsusb2_reset";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		gpio = <&gpio5 19 0>;	/* gpio_147 */
-		startup-delay-us = <70000>;
-		enable-active-high;
-	};
-
 	/* HS USB Port 2 Power */
 	hsusb2_power: hsusb2_power_reg {
 		compatible = "regulator-fixed";
@@ -68,7 +57,7 @@ hsusb2_power: hsusb2_power_reg {
 	/* HS USB Host PHY on PORT 2 */
 	hsusb2_phy: hsusb2_phy {
 		compatible = "usb-nop-xceiv";
-		reset-supply = <&hsusb2_reset>;
+		reset-gpios = <&gpio5 19 GPIO_ACTIVE_LOW>;	/* gpio_147 */
 		vcc-supply = <&hsusb2_power>;
 	};
 
@@ -101,18 +90,18 @@ &hsusbb2_pins
 
 	hsusbb2_pins: pinmux_hsusbb2_pins {
 		pinctrl-single,pins = <
-			0x5c0 (PIN_OUTPUT | MUX_MODE3)		/* usbb2_ulpitll_clk.usbb1_ulpiphy_clk */
-			0x5c2 (PIN_OUTPUT | MUX_MODE3)		/* usbb2_ulpitll_clk.usbb1_ulpiphy_stp */
-			0x5c4 (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* usbb2_ulpitll_clk.usbb1_ulpiphy_dir */
-			0x5c6 (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* usbb2_ulpitll_clk.usbb1_ulpiphy_nxt */
-			0x5c8 (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* usbb2_ulpitll_clk.usbb1_ulpiphy_dat0 */
-			0x5cA (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* usbb2_ulpitll_clk.usbb1_ulpiphy_dat1 */
-			0x1a4 (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* usbb2_ulpitll_clk.usbb1_ulpiphy_dat2 */
-			0x1a6 (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* usbb2_ulpitll_clk.usbb1_ulpiphy_dat3 */
-			0x1a8 (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* usbb2_ulpitll_clk.usbb1_ulpiphy_dat4 */
-			0x1aa (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* usbb2_ulpitll_clk.usbb1_ulpiphy_dat5 */
-			0x1ac (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* usbb2_ulpitll_clk.usbb1_ulpiphy_dat6 */
-			0x1ae (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* usbb2_ulpitll_clk.usbb1_ulpiphy_dat7 */
+			0x5c0 (PIN_OUTPUT | MUX_MODE3)		/* etk_d10.hsusb2_clk */
+			0x5c2 (PIN_OUTPUT | MUX_MODE3)		/* etk_d11.hsusb2_stp */
+			0x5c4 (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* etk_d12.hsusb2_dir */
+			0x5c6 (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* etk_d13.hsusb2_nxt */
+			0x5c8 (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* etk_d14.hsusb2_data0 */
+			0x5cA (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* etk_d15.hsusb2_data1 */
+			0x1a4 (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* mcspi1_cs3.hsusb2_data2 */
+			0x1a6 (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* mcspi2_clk.hsusb2_data7 */
+			0x1a8 (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* mcspi2_simo.hsusb2_data4 */
+			0x1aa (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* mcspi2_somi.hsusb2_data5 */
+			0x1ac (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* mcspi2_cs0.hsusb2_data6 */
+			0x1ae (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* mcspi2_cs1.hsusb2_data3 */
 		>;
 	};
 
@@ -180,3 +169,10 @@ &gpio1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&gpio1_pins>;
 };
+
+&usb_otg_hs {
+	interface-type = <0>;
+	usb-phy = <&usb2_phy>;
+	mode = <3>;
+	power = <50>;
+};

arch/arm/boot/dts/omap3-devkit8000.dts

@@ -125,7 +125,7 @@ nand@0,0 {
 		nand-bus-width = <16>;
 
 		gpmc,device-nand;
-		gpmc,sync-clki-ps = <0>;
+		gpmc,sync-clk-ps = <0>;
 		gpmc,cs-on-ns = <0>;
 		gpmc,cs-rd-off-ns = <44>;
 		gpmc,cs-wr-off-ns = <44>;

arch/arm/boot/dts/omap3-gta04.dts

+/*
+ * Copyright (C) 2013 Marek Belisko <marek@goldelico.com>
+ *
+ * Based on omap3-beagle-xm.dts
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+/dts-v1/;
+
+#include "omap36xx.dtsi"
+
+/ {
+	model = "OMAP3 GTA04";
+	compatible = "ti,omap3-gta04", "ti,omap3";
+
+	cpus {
+		cpu@0 {
+			cpu0-supply = <&vcc>;
+		};
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0x80000000 0x20000000>; /* 512 MB */
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		aux-button {
+			label = "aux";
+			linux,code = <169>;
+			gpios = <&gpio1 7 GPIO_ACTIVE_LOW>;
+			gpio-key,wakeup;
+		};
+	};
+};
+
+&omap3_pmx_core {
+	uart1_pins: pinmux_uart1_pins {
+		pinctrl-single,pins = <
+			0x152 (PIN_INPUT | MUX_MODE0)		/* uart1_rx.uart1_rx */
+			0x14c (PIN_OUTPUT |MUX_MODE0)		/* uart1_tx.uart1_tx */
+		>;
+	};
+
+	uart2_pins: pinmux_uart2_pins {
+		pinctrl-single,pins = <
+			0x14a (PIN_INPUT | MUX_MODE0)		/* uart2_rx.uart2_rx */
+			0x148 (PIN_OUTPUT | MUX_MODE0)		/* uart2_tx.uart2_tx */
+		>;
+	};
+
+	uart3_pins: pinmux_uart3_pins {
+		pinctrl-single,pins = <
+			0x16e (PIN_INPUT | MUX_MODE0)		/* uart3_rx.uart3_rx */
+			0x170 (PIN_OUTPUT | MUX_MODE0)		/* uart3_tx.uart3_tx */
+		>;
+	};
+
+	mmc1_pins: pinmux_mmc1_pins {
+		pinctrl-single,pins = <
+			0x114 (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc1_clk.sdmmc1_clk */
+			0x116 (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc1_cmd.sdmmc1_cmd */
+			0x118 (PIN_INPUT_PULLUP | MUX_MODE0) 	/* sdmmc1_dat0.sdmmc1_dat0 */
+			0x11a (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc1_dat1.sdmmc1_dat1 */
+			0x11c (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc1_dat2.sdmmc1_dat2 */
+			0x11e (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc1_dat3.sdmmc1_dat3 */
+		>;
+	};
+};
+
+&i2c1 {
+	clock-frequency = <2600000>;
+
+	twl: twl@48 {
+		reg = <0x48>;
+		interrupts = <7>; /* SYS_NIRQ cascaded to intc */
+		interrupt-parent = <&intc>;
+	};
+};
+
+#include "twl4030.dtsi"
+#include "twl4030_omap3.dtsi"
+
+&i2c2 {
+	clock-frequency = <400000>;
+
+	/* pressure sensor */
+	bmp085@77 {
+		compatible = "bosch,bmp085";
+		reg = <0x77>;
+	};
+
+	/* leds */
+	tca6507@45 {
+		compatible = "ti,tca6507";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x45>;
+
+		gta04_led0: red_aux@0 {
+			label = "gta04:red:aux";
+			reg = <0x0>;
+		};
+
+		gta04_led1: green_aux@1 {
+			label = "gta04:green:aux";
+			reg = <0x1>;
+		};
+
+		gta04_led3: red_power@3 {
+			label = "gta04:red:power";
+			reg = <0x3>;
+			linux,default-trigger = "default-on";
+		};
+
+		gta04_led4: green_power@4 {
+			label = "gta04:green:power";
+			reg = <0x4>;
+		};
+	};
+};
+
+&i2c3 {
+	clock-frequency = <100000>;
+};
+
+&usb_otg_hs {
+	interface-type = <0>;
+	usb-phy = <&usb2_phy>;
+	mode = <3>;
+	power = <50>;
+};
+
+&mmc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc1_pins>;
+	vmmc-supply = <&vmmc1>;
+	vmmc_aux-supply = <&vsim>;
+	bus-width = <4>;
+};
+
+&mmc2 {
+	status = "disabled";
+};
+
+&mmc3 {
+	status = "disabled";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_pins>;
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart2_pins>;
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart3_pins>;
+};
+

arch/arm/boot/dts/omap3-igep.dtsi

@@ -77,6 +77,8 @@ smsc911x_pins: pinmux_smsc911x_pins {
 			0x1a2 (PIN_INPUT | MUX_MODE4)		/* mcspi1_cs2.gpio_176 */
 		>;
 	};
+
+	leds_pins: pinmux_leds_pins { };
 };
 
 &i2c1 {
@@ -141,3 +143,12 @@ &uart3 {
 &twl_gpio {
 	ti,use-leds;
 };
+
+&usb_otg_hs {
+	interface-type = <0>;
+	usb-phy = <&usb2_phy>;
+	phys = <&usb2_phy>;
+	phy-names = "usb2-phy";
+	mode = <3>;
+	power = <50>;
+};

arch/arm/boot/dts/omap3-igep0020.dts

@@ -16,7 +16,10 @@ / {
 	compatible = "isee,omap3-igep0020", "ti,omap3";
 
 	leds {
+		pinctrl-names = "default";
+		pinctrl-0 = <&leds_pins>;
 		compatible = "gpio-leds";
+
 		boot {
 			 label = "omap3:green:boot";
 			 gpios = <&gpio1 26 GPIO_ACTIVE_HIGH>;
@@ -52,6 +55,55 @@ vdd33a: regulator-vdd33a {
 		regulator-name = "vdd33a";
 		regulator-always-on;
 	};
+
+       /* HS USB Port 1 Power */
+       hsusb1_power: hsusb1_power_reg {
+               compatible = "regulator-fixed";
+               regulator-name = "hsusb1_vbus";
+               regulator-min-microvolt = <3300000>;
+               regulator-max-microvolt = <3300000>;
+               gpio = <&twl_gpio 18 GPIO_ACTIVE_LOW>;	/* GPIO LEDA */
+               startup-delay-us = <70000>;
+       };
+
+	/* HS USB Host PHY on PORT 1 */
+	hsusb1_phy: hsusb1_phy {
+		compatible = "usb-nop-xceiv";
+		reset-gpios = <&gpio1 24 GPIO_ACTIVE_LOW>; /* gpio_24 */
+		vcc-supply = <&hsusb1_power>;
+	};
+};
+
+&omap3_pmx_core {
+	pinctrl-names = "default";
+	pinctrl-0 = <
+		&hsusbb1_pins
+	>;
+
+	hsusbb1_pins: pinmux_hsusbb1_pins {
+		pinctrl-single,pins = <
+			0x5aa (PIN_OUTPUT | MUX_MODE3)		/* etk_ctl.hsusb1_clk */
+			0x5a8 (PIN_OUTPUT | MUX_MODE3)		/* etk_clk.hsusb1_stp */
+			0x5bc (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* etk_d8.hsusb1_dir */
+			0x5be (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* etk_d9.hsusb1_nxt */
+			0x5ac (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* etk_d0.hsusb1_data0 */
+			0x5ae (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* etk_d1.hsusb1_data1 */
+			0x5b0 (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* etk_d2.hsusb1_data2 */
+			0x5b2 (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* etk_d3.hsusb1_data7 */
+			0x5b4 (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* etk_d4.hsusb1_data4 */
+			0x5b6 (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* etk_d5.hsusb1_data5 */
+			0x5b8 (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* etk_d6.hsusb1_data6 */
+			0x5ba (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* etk_d7.hsusb1_data3 */
+		>;
+	};
+};
+
+&leds_pins {
+	pinctrl-single,pins = <
+		0x5c4 (PIN_OUTPUT | MUX_MODE4) /* etk_d12.gpio_26 */
+		0x5c6 (PIN_OUTPUT | MUX_MODE4) /* etk_d13.gpio_27 */
+		0x5c8 (PIN_OUTPUT | MUX_MODE4) /* etk_d14.gpio_28 */
+	>;
 };
 
 &i2c3 {
@@ -99,19 +151,19 @@ partition@0 {
 			label = "SPL";
 			reg = <0 0x100000>;
 		};
-		partition@0x80000 {
+		partition@80000 {
 			label = "U-Boot";
 			reg = <0x100000 0x180000>;
 		};
-		partition@0x1c0000 {
+		partition@1c0000 {
 			label = "Environment";
 			reg = <0x280000 0x100000>;
 		};
-		partition@0x280000 {
+		partition@280000 {
 			label = "Kernel";
 			reg = <0x380000 0x300000>;
 		};
-		partition@0x780000 {
+		partition@780000 {
 			label = "Filesystem";
 			reg = <0x680000 0x1f980000>;
 		};
@@ -147,7 +199,7 @@ ethernet@5,0 {
 		gpmc,cycle2cycle-diffcsen;
 
 		interrupt-parent = <&gpio6>;
-		interrupts = <16 8>;
+		interrupts = <16 IRQ_TYPE_LEVEL_LOW>;
 		vmmc-supply = <&vddvario>;
 		vmmc_aux-supply = <&vdd33a>;
 		reg-io-width = <4>;
@@ -155,3 +207,11 @@ ethernet@5,0 {
 		smsc,save-mac-address;
 	};
 };
+
+&usbhshost {
+	port1-mode = "ehci-phy";
+};
+
+&usbhsehci {
+	phys = <&hsusb1_phy>;
+};

arch/arm/boot/dts/omap3-igep0030.dts

@@ -16,7 +16,10 @@ / {
 	compatible = "isee,omap3-igep0030", "ti,omap3";
 
 	leds {
+		pinctrl-names = "default";
+		pinctrl-0 = <&leds_pins>;
 		compatible = "gpio-leds";
+
 		boot {
 			 label = "omap3:green:boot";
 			 gpios = <&twl_gpio 13 GPIO_ACTIVE_LOW>;
@@ -43,6 +46,12 @@ user2 {
 	};
 };
 
+&leds_pins {
+	pinctrl-single,pins = <
+		0x5b0 (PIN_OUTPUT | MUX_MODE4) /* etk_d2.gpio_16 */
+	>;
+};
+
 &gpmc {
 	ranges = <0 0 0x00000000 0x20000000>;
 
@@ -74,19 +83,19 @@ partition@0 {
 			label = "SPL";
 			reg = <0 0x100000>;
 		};
-		partition@0x80000 {
+		partition@80000 {
 			label = "U-Boot";
 			reg = <0x100000 0x180000>;
 		};
-		partition@0x1c0000 {
+		partition@1c0000 {
 			label = "Environment";
 			reg = <0x280000 0x100000>;
 		};
-		partition@0x280000 {
+		partition@280000 {
 			label = "Kernel";
 			reg = <0x380000 0x300000>;
 		};
-		partition@0x780000 {
+		partition@780000 {
 			label = "Filesystem";
 			reg = <0x680000 0x1f980000>;
 		};

arch/arm/boot/dts/omap3-n900.dts

+/*
+ * Copyright (C) 2013 Pavel Machek <pavel@ucw.cz>
+ * Copyright 2013 Aaro Koskinen <aaro.koskinen@iki.fi>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 (or later) as
+ * published by the Free Software Foundation.
+ */
+
+/dts-v1/;
+
+#include "omap34xx.dtsi"
+
+/ {
+	model = "Nokia N900";
+	compatible = "nokia,omap3-n900", "ti,omap3";
+
+	cpus {
+		cpu@0 {
+			cpu0-supply = <&vcc>;
+		};
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0x80000000 0x10000000>; /* 256 MB */
+	};
+
+};
+
+&i2c1 {
+	clock-frequency = <2200000>;
+
+	twl: twl@48 {
+		reg = <0x48>;
+		interrupts = <7>; /* SYS_NIRQ cascaded to intc */
+		interrupt-parent = <&intc>;
+	};
+};
+
+#include "twl4030.dtsi"
+
+&twl_gpio {
+	ti,pullups	= <0x0>;
+	ti,pulldowns	= <0x03ff3f>; /* BIT(0..5) | BIT(8..17) */
+};
+
+&i2c2 {
+	clock-frequency = <400000>;
+};
+
+&i2c3 {
+	clock-frequency = <100000>;
+};
+
+&mmc1 {
+	status = "disabled";
+};
+
+&mmc2 {
+	status = "disabled";
+};
+
+&mmc3 {
+	status = "disabled";
+};
+
+&mcspi1 {
+	/*
+	 * For some reason, touchscreen is necessary for screen to work at
+	 * all on real hw. It works well without it on emulator.
+	 *
+	 * Also... order in the device tree actually matters here.
+	 */
+	tsc2005@0 {
+		compatible = "tsc2005";
+		spi-max-frequency = <6000000>;
+		reg = <0>;
+	};
+	mipid@2 {
+		compatible = "acx565akm";
+		spi-max-frequency = <6000000>;
+		reg = <2>;
+	};
+};
+
+&usb_otg_hs {
+	interface-type = <0>;
+	usb-phy = <&usb2_phy>;
+	mode = <2>;
+	power = <50>;
+};

arch/arm/boot/dts/omap3.dtsi

@@ -107,15 +107,19 @@ omap3_pmx_core: pinmux@48002030 {
 			reg = <0x48002030 0x05cc>;
 			#address-cells = <1>;
 			#size-cells = <0>;
+			#interrupt-cells = <1>;
+			interrupt-controller;
 			pinctrl-single,register-width = <16>;
 			pinctrl-single,function-mask = <0xff1f>;
 		};
 
-		omap3_pmx_wkup: pinmux@0x48002a00 {
+		omap3_pmx_wkup: pinmux@48002a00 {
 			compatible = "ti,omap3-padconf", "pinctrl-single";
 			reg = <0x48002a00 0x5c>;
 			#address-cells = <1>;
 			#size-cells = <0>;
+			#interrupt-cells = <1>;
+			interrupt-controller;
 			pinctrl-single,register-width = <16>;
 			pinctrl-single,function-mask = <0xff1f>;
 		};

arch/arm/boot/dts/omap3430-sdp.dts

@@ -84,15 +84,15 @@ partition@0 {
 			label = "bootloader-nor";
 			reg = <0 0x40000>;
 		};
-		partition@0x40000 {
+		partition@40000 {
 			label = "params-nor";
 			reg = <0x40000 0x40000>;
 		};
-		partition@0x80000 {
+		partition@80000 {
 			label = "kernel-nor";
 			reg = <0x80000 0x200000>;
 		};
-		partition@0x280000 {
+		partition@280000 {
 			label = "filesystem-nor";
 			reg = <0x240000 0x7d80000>;
 		};
@@ -125,19 +125,19 @@ partition@0 {
 			label = "xloader-nand";
 			reg = <0 0x80000>;
 		};
-		partition@0x80000 {
+		partition@80000 {
 			label = "bootloader-nand";
 			reg = <0x80000 0x140000>;
 		};
-		partition@0x1c0000 {
+		partition@1c0000 {
 			label = "params-nand";
 			reg = <0x1c0000 0xc0000>;
 		};
-		partition@0x280000 {
+		partition@280000 {
 			label = "kernel-nand";
 			reg = <0x280000 0x500000>;
 		};
-		partition@0x780000 {
+		partition@780000 {
 			label = "filesystem-nand";
 			reg = <0x780000 0x7880000>;
 		};
@@ -170,19 +170,19 @@ partition@0 {
 			label = "xloader-onenand";
 			reg = <0 0x80000>;
 		};
-		partition@0x80000 {
+		partition@80000 {
 			label = "bootloader-onenand";
 			reg = <0x80000 0x40000>;
 		};
-		partition@0xc0000 {
+		partition@c0000 {
 			label = "params-onenand";
 			reg = <0xc0000 0x20000>;
 		};
-		partition@0xe0000 {
+		partition@e0000 {
 			label = "kernel-onenand";
 			reg = <0xe0000 0x200000>;
 		};
-		partition@0x2e0000 {
+		partition@2e0000 {
 			label = "filesystem-onenand";
 			reg = <0x2e0000 0xfd20000>;
 		};

arch/arm/boot/dts/omap4-panda-common.dtsi

@@ -60,22 +60,6 @@ sound: sound {
 			"AFMR", "Line In";
 	};
 
-	/*
-	 * Temp hack: Need to be replaced with the proper gpio-controlled
-	 * reset driver as soon it will be merged.
-	 * http://thread.gmane.org/gmane.linux.drivers.devicetree/36830
-	 */
-	/* HS USB Port 1 RESET */
-	hsusb1_reset: hsusb1_reset_reg {
-		compatible = "regulator-fixed";
-		regulator-name = "hsusb1_reset";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		gpio = <&gpio2 30 0>;	/* gpio_62 */
-		startup-delay-us = <70000>;
-		enable-active-high;
-	};
-
 	/* HS USB Port 1 Power */
 	hsusb1_power: hsusb1_power_reg {
 		compatible = "regulator-fixed";
@@ -97,7 +81,7 @@ hsusb1_power: hsusb1_power_reg {
 	/* HS USB Host PHY on PORT 1 */
 	hsusb1_phy: hsusb1_phy {
 		compatible = "usb-nop-xceiv";
-		reset-supply = <&hsusb1_reset>;
+		reset-gpios = <&gpio2 30 GPIO_ACTIVE_LOW>;   /* gpio_62 */
 		vcc-supply = <&hsusb1_power>;
 	/**
 	 * FIXME:
@@ -122,23 +106,9 @@ wl12xx_vmmc: wl12xx_vmmc {
 	};
 };
 
-&omap4_pmx_wkup {
-	pinctrl-names = "default";
-	pinctrl-0 = <
-			&twl6030_wkup_pins
-	>;
-
-	twl6030_wkup_pins: pinmux_twl6030_wkup_pins {
-		pinctrl-single,pins = <
-			0x14 (PIN_OUTPUT | MUX_MODE2)		/* fref_clk0_out.sys_drm_msecure */
-		>;
-	};
-};
-
 &omap4_pmx_core {
 	pinctrl-names = "default";
 	pinctrl-0 = <
-			&twl6030_pins
 			&twl6040_pins
 			&mcpdm_pins
 			&mcbsp1_pins
@@ -147,12 +117,6 @@ &tpd12s015_pins
 			&hsusbb1_pins
 	>;
 
-	twl6030_pins: pinmux_twl6030_pins {
-		pinctrl-single,pins = <
-			0x15e (WAKEUP_EN | PIN_INPUT_PULLUP | MUX_MODE0)	/* sys_nirq1.sys_nirq1 */
-		>;
-	};
-
 	twl6040_pins: pinmux_twl6040_pins {
 		pinctrl-single,pins = <
 			0xe0 (PIN_OUTPUT | MUX_MODE3)	/* hdq_sio.gpio_127 */
@@ -305,6 +269,7 @@ twl6040: twl@4b {
 };
 
 #include "twl6030.dtsi"
+#include "twl6030_omap4.dtsi"
 
 &i2c2 {
 	pinctrl-names = "default";

arch/arm/boot/dts/omap4-sdp.dts

@@ -155,23 +155,9 @@ wl12xx_vmmc: wl12xx_vmmc {
 	};
 };
 
-&omap4_pmx_wkup {
-	pinctrl-names = "default";
-	pinctrl-0 = <
-			&twl6030_wkup_pins
-	>;
-
-	twl6030_wkup_pins: pinmux_twl6030_wkup_pins {
-		pinctrl-single,pins = <
-			0x14 (PIN_OUTPUT | MUX_MODE2)		/* fref_clk0_out.sys_drm_msecure */
-		>;
-	};
-};
-
 &omap4_pmx_core {
 	pinctrl-names = "default";
 	pinctrl-0 = <
-			&twl6030_pins
 			&twl6040_pins
 			&mcpdm_pins
 			&dmic_pins
@@ -206,12 +192,6 @@ uart4_pins: pinmux_uart4_pins {
 		>;
 	};
 
-	twl6030_pins: pinmux_twl6030_pins {
-		pinctrl-single,pins = <
-			0x15e (WAKEUP_EN | PIN_INPUT_PULLUP | MUX_MODE0)	/* sys_nirq1.sys_nirq1 */
-		>;
-	};
-
 	twl6040_pins: pinmux_twl6040_pins {
 		pinctrl-single,pins = <
 			0xe0 (PIN_OUTPUT | MUX_MODE3)		/* hdq_sio.gpio_127 */
@@ -370,6 +350,7 @@ vibra {
 };
 
 #include "twl6030.dtsi"
+#include "twl6030_omap4.dtsi"
 
 &i2c2 {
 	pinctrl-names = "default";

arch/arm/boot/dts/omap4.dtsi

@@ -56,7 +56,7 @@ L2: l2-cache-controller@48242000 {
 		cache-level = <2>;
 	};
 
-	local-timer@0x48240600 {
+	local-timer@48240600 {
 		compatible = "arm,cortex-a9-twd-timer";
 		reg = <0x48240600 0x20>;
 		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_RAW(3) | IRQ_TYPE_LEVEL_HIGH)>;
@@ -114,6 +114,8 @@ omap4_pmx_core: pinmux@4a100040 {
 			reg = <0x4a100040 0x0196>;
 			#address-cells = <1>;
 			#size-cells = <0>;
+			#interrupt-cells = <1>;
+			interrupt-controller;
 			pinctrl-single,register-width = <16>;
 			pinctrl-single,function-mask = <0x7fff>;
 		};
@@ -122,6 +124,8 @@ omap4_pmx_wkup: pinmux@4a31e040 {
 			reg = <0x4a31e040 0x0038>;
 			#address-cells = <1>;
 			#size-cells = <0>;
+			#interrupt-cells = <1>;
+			interrupt-controller;
 			pinctrl-single,register-width = <16>;
 			pinctrl-single,function-mask = <0x7fff>;
 		};
@@ -663,5 +667,23 @@ usb_otg_hs: usb_otg_hs@4a0ab000 {
 			ram-bits = <12>;
 			ti,has-mailbox;
 		};
+
+		aes: aes@4b501000 {
+			compatible = "ti,omap4-aes";
+			ti,hwmods = "aes";
+			reg = <0x4b501000 0xa0>;
+			interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
+			dmas = <&sdma 111>, <&sdma 110>;
+			dma-names = "tx", "rx";
+		};
+
+		des: des@480a5000 {
+			compatible = "ti,omap4-des";
+			ti,hwmods = "des";
+			reg = <0x480a5000 0xa0>;
+			interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
+			dmas = <&sdma 117>, <&sdma 116>;
+			dma-names = "tx", "rx";
+		};
 	};
 };

arch/arm/boot/dts/omap5-uevm.dts

@@ -27,21 +27,10 @@ vmmcsd_fixed: fixedregulator-mmcsd {
 		regulator-max-microvolt = <3000000>;
 	};
 
-	/* HS USB Port 2 RESET */
-	hsusb2_reset: hsusb2_reset_reg {
-		compatible = "regulator-fixed";
-		regulator-name = "hsusb2_reset";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		gpio = <&gpio3 16 GPIO_ACTIVE_HIGH>; /* gpio3_80 HUB_NRESET */
-		startup-delay-us = <70000>;
-		enable-active-high;
-	};
-
 	/* HS USB Host PHY on PORT 2 */
 	hsusb2_phy: hsusb2_phy {
 		compatible = "usb-nop-xceiv";
-		reset-supply = <&hsusb2_reset>;
+		reset-gpios = <&gpio3 16 GPIO_ACTIVE_LOW>; /* gpio3_80 HUB_NRESET */
 	/**
 	  * FIXME
 	  * Put the right clock phandle here when available
@@ -51,21 +40,10 @@ hsusb2_phy: hsusb2_phy {
 		clock-frequency = <19200000>;
 	};
 
-	/* HS USB Port 3 RESET */
-	hsusb3_reset: hsusb3_reset_reg {
-		compatible = "regulator-fixed";
-		regulator-name = "hsusb3_reset";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		gpio = <&gpio3 15 GPIO_ACTIVE_HIGH>; /* gpio3_79 ETH_NRESET */
-		startup-delay-us = <70000>;
-		enable-active-high;
-	};
-
 	/* HS USB Host PHY on PORT 3 */
 	hsusb3_phy: hsusb3_phy {
 		compatible = "usb-nop-xceiv";
-		reset-supply = <&hsusb3_reset>;
+		reset-gpios = <&gpio3 15 GPIO_ACTIVE_LOW>; /* gpio3_79 ETH_NRESET */
 	};
 
 	leds {
@@ -271,6 +249,14 @@ palmas: palmas@48 {
 		reg = <0x48>;
 		interrupt-controller;
 		#interrupt-cells = <2>;
+		ti,system-power-controller;
+
+		extcon_usb3: palmas_usb {
+			compatible = "ti,palmas-usb-vid";
+			ti,enable-vbus-detection;
+			ti,enable-id-detection;
+			ti,wakeup;
+		};
 
 		palmas_pmic {
 			compatible = "ti,palmas-pmic";
@@ -334,9 +320,18 @@ smps9_reg: smps9 {
 					ti,smps-range = <0x80>;
 				};
 
-				smps10_reg: smps10 {
+				smps10_out2_reg: smps10_out2 {
 					/* VBUS_5V_OTG */
-					regulator-name = "smps10";
+					regulator-name = "smps10_out2";
+					regulator-min-microvolt = <5000000>;
+					regulator-max-microvolt = <5000000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				smps10_out1_reg: smps10_out1 {
+					/* VBUS_5V_OTG */
+					regulator-name = "smps10_out1";
 					regulator-min-microvolt = <5000000>;
 					regulator-max-microvolt = <5000000>;
 					regulator-always-on;
@@ -470,6 +465,11 @@ &usbhsehci {
 	phys = <0 &hsusb2_phy &hsusb3_phy>;
 };
 
+&usb3 {
+	extcon = <&extcon_usb3>;
+	vbus-supply = <&smps10_out1_reg>;
+};
+
 &mcspi1 {
 
 };

arch/arm/boot/dts/omap5.dtsi

@@ -604,7 +604,7 @@ wdt2: wdt@4ae14000 {
 			ti,hwmods = "wd_timer2";
 		};
 
-		emif1: emif@0x4c000000 {
+		emif1: emif@4c000000 {
 			compatible	= "ti,emif-4d5";
 			ti,hwmods	= "emif1";
 			phy-type	= <2>; /* DDR PHY type: Intelli PHY */
@@ -615,7 +615,7 @@ emif1: emif@0x4c000000 {
 			hw-caps-temp-alert;
 		};
 
-		emif2: emif@0x4d000000 {
+		emif2: emif@4d000000 {
 			compatible	= "ti,emif-4d5";
 			ti,hwmods	= "emif2";
 			phy-type	= <2>; /* DDR PHY type: Intelli PHY */
@@ -634,7 +634,7 @@ omap_control_usb: omap-control-usb@4a002300 {
 			ti,type = <2>;
 		};
 
-		omap_dwc3@4a020000 {
+		usb3: omap_dwc3@4a020000 {
 			compatible = "ti,dwc3";
 			ti,hwmods = "usb_otg_ss";
 			reg = <0x4a020000 0x10000>;

arch/arm/boot/dts/twl6030_omap4.dtsi

+/*
+ * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+&twl {
+	/*
+	 * On most OMAP4 platforms, the twl6030 IRQ line is connected
+	 * to the SYS_NIRQ1 line on OMAP and the twl6030 MSECURE line is
+	 * connected to the fref_clk0_out.sys_drm_msecure line.
+	 * Therefore, configure the defaults for the SYS_NIRQ1 and
+	 * fref_clk0_out.sys_drm_msecure pins here.
+	 */
+	pinctrl-names = "default";
+	pinctrl-0 = <
+		&twl6030_pins
+		&twl6030_wkup_pins
+	>;
+};
+
+&omap4_pmx_wkup {
+	twl6030_wkup_pins: pinmux_twl6030_wkup_pins {
+		pinctrl-single,pins = <
+			0x14 (PIN_OUTPUT | MUX_MODE2)		/* fref_clk0_out.sys_drm_msecure */
+		>;
+	};
+};
+
+&omap4_pmx_core {
+	twl6030_pins: pinmux_twl6030_pins {
+		pinctrl-single,pins = <
+			0x15e (WAKEUP_EN | PIN_INPUT_PULLUP | MUX_MODE0)	/* sys_nirq1.sys_nirq1 */
+		>;
+	};
+};

arch/arm/configs/omap2plus_defconfig

-CONFIG_EXPERIMENTAL=y
 CONFIG_SYSVIPC=y
 CONFIG_POSIX_MQUEUE=y
+CONFIG_NO_HZ=y
+CONFIG_HIGH_RES_TIMERS=y
 CONFIG_BSD_PROCESS_ACCT=y
 CONFIG_IKCONFIG=y
 CONFIG_IKCONFIG_PROC=y
 CONFIG_LOG_BUF_SHIFT=16
 CONFIG_BLK_DEV_INITRD=y
 CONFIG_EXPERT=y
-# CONFIG_SYSCTL_SYSCALL is not set
-CONFIG_KALLSYMS_EXTRA_PASS=y
 CONFIG_SLAB=y
 CONFIG_PROFILING=y
 CONFIG_OPROFILE=y
@@ -20,22 +19,21 @@ CONFIG_MODULE_FORCE_UNLOAD=y
 CONFIG_MODVERSIONS=y
 CONFIG_MODULE_SRCVERSION_ALL=y
 # CONFIG_BLK_DEV_BSG is not set
+CONFIG_PARTITION_ADVANCED=y
 CONFIG_ARCH_MULTI_V6=y
-CONFIG_ARCH_OMAP2PLUS=y
+CONFIG_OMAP_RESET_CLOCKS=y
+CONFIG_OMAP_MUX_DEBUG=y
 CONFIG_ARCH_OMAP2=y
 CONFIG_ARCH_OMAP3=y
 CONFIG_ARCH_OMAP4=y
+CONFIG_SOC_OMAP5=y
 CONFIG_SOC_AM33XX=y
-CONFIG_OMAP_RESET_CLOCKS=y
-CONFIG_OMAP_MUX_DEBUG=y
-CONFIG_ARCH_VEXPRESS_CA9X4=y
+CONFIG_SOC_DRA7XX=y
 CONFIG_ARM_THUMBEE=y
 CONFIG_ARM_ERRATA_411920=y
-CONFIG_NO_HZ=y
-CONFIG_HIGH_RES_TIMERS=y
 CONFIG_SMP=y
 CONFIG_NR_CPUS=2
-CONFIG_LEDS=y
+CONFIG_CMA=y
 CONFIG_ZBOOT_ROM_TEXT=0x0
 CONFIG_ZBOOT_ROM_BSS=0x0
 CONFIG_ARM_APPENDED_DTB=y
@@ -61,8 +59,6 @@ CONFIG_IP_PNP_RARP=y
 # CONFIG_IPV6 is not set
 CONFIG_NETFILTER=y
 CONFIG_CAN=m
-CONFIG_CAN_RAW=m
-CONFIG_CAN_BCM=m
 CONFIG_CAN_C_CAN=m
 CONFIG_CAN_C_CAN_PLATFORM=m
 CONFIG_BT=m
@@ -77,14 +73,13 @@ CONFIG_MAC80211=m
 CONFIG_MAC80211_RC_PID=y
 CONFIG_MAC80211_RC_DEFAULT_PID=y
 CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
-CONFIG_CMA=y
-CONFIG_DMA_CMA=y
-CONFIG_CONNECTOR=y
 CONFIG_DEVTMPFS=y
 CONFIG_DEVTMPFS_MOUNT=y
+CONFIG_DMA_CMA=y
+CONFIG_OMAP_OCP2SCP=y
+CONFIG_CONNECTOR=y
 CONFIG_MTD=y
 CONFIG_MTD_CMDLINE_PARTS=y
-CONFIG_MTD_CHAR=y
 CONFIG_MTD_BLOCK=y
 CONFIG_MTD_OOPS=y
 CONFIG_MTD_CFI=y
@@ -98,32 +93,40 @@ CONFIG_MTD_UBI=y
 CONFIG_BLK_DEV_LOOP=y
 CONFIG_BLK_DEV_RAM=y
 CONFIG_BLK_DEV_RAM_SIZE=16384
-CONFIG_SENSORS_LIS3LV02D=m
 CONFIG_SENSORS_TSL2550=m
-CONFIG_SENSORS_LIS3_I2C=m
 CONFIG_BMP085_I2C=m
+CONFIG_SENSORS_LIS3_I2C=m
 CONFIG_SCSI=y
 CONFIG_BLK_DEV_SD=y
 CONFIG_SCSI_MULTI_LUN=y
 CONFIG_SCSI_SCAN_ASYNC=y
 CONFIG_MD=y
 CONFIG_NETDEVICES=y
-CONFIG_SMSC_PHY=y
-CONFIG_NET_ETHERNET=y
-CONFIG_SMC91X=y
-CONFIG_SMSC911X=y
 CONFIG_KS8851=y
 CONFIG_KS8851_MLL=y
-CONFIG_LIBERTAS=m
-CONFIG_LIBERTAS_USB=m
-CONFIG_LIBERTAS_SDIO=m
-CONFIG_LIBERTAS_DEBUG=y
+CONFIG_SMC91X=y
+CONFIG_SMSC911X=y
+CONFIG_TI_CPSW=y
+CONFIG_AT803X_PHY=y
+CONFIG_SMSC_PHY=y
 CONFIG_USB_USBNET=y
 CONFIG_USB_NET_SMSC95XX=y
 CONFIG_USB_ALI_M5632=y
 CONFIG_USB_AN2720=y
 CONFIG_USB_EPSON2888=y
 CONFIG_USB_KC2190=y
+CONFIG_LIBERTAS=m
+CONFIG_LIBERTAS_USB=m
+CONFIG_LIBERTAS_SDIO=m
+CONFIG_LIBERTAS_DEBUG=y
+CONFIG_WL_TI=y
+CONFIG_WL12XX=m
+CONFIG_WL18XX=m
+CONFIG_WLCORE_SPI=m
+CONFIG_WLCORE_SDIO=m
+CONFIG_MWIFIEX=m
+CONFIG_MWIFIEX_SDIO=m
+CONFIG_MWIFIEX_USB=m
 CONFIG_INPUT_JOYDEV=y
 CONFIG_INPUT_EVDEV=y
 CONFIG_KEYBOARD_GPIO=y
@@ -133,7 +136,6 @@ CONFIG_INPUT_TOUCHSCREEN=y
 CONFIG_TOUCHSCREEN_ADS7846=y
 CONFIG_INPUT_MISC=y
 CONFIG_INPUT_TWL4030_PWRBUTTON=y
-CONFIG_VT_HW_CONSOLE_BINDING=y
 # CONFIG_LEGACY_PTYS is not set
 CONFIG_SERIAL_8250=y
 CONFIG_SERIAL_8250_CONSOLE=y
@@ -143,8 +145,7 @@ CONFIG_SERIAL_8250_MANY_PORTS=y
 CONFIG_SERIAL_8250_SHARE_IRQ=y
 CONFIG_SERIAL_8250_DETECT_IRQ=y
 CONFIG_SERIAL_8250_RSA=y
-CONFIG_SERIAL_AMBA_PL011=y
-CONFIG_SERIAL_AMBA_PL011_CONSOLE=y
+CONFIG_SERIAL_OF_PLATFORM=y
 CONFIG_SERIAL_OMAP=y
 CONFIG_SERIAL_OMAP_CONSOLE=y
 CONFIG_HW_RANDOM=y
@@ -158,31 +159,31 @@ CONFIG_GPIO_TWL4030=y
 CONFIG_W1=y
 CONFIG_POWER_SUPPLY=y
 CONFIG_SENSORS_LM75=m
-CONFIG_WATCHDOG=y
 CONFIG_THERMAL=y
-CONFIG_THERMAL_HWMON=y
-CONFIG_THERMAL_DEFAULT_GOV_STEP_WISE=y
 CONFIG_THERMAL_GOV_FAIR_SHARE=y
-CONFIG_THERMAL_GOV_STEP_WISE=y
 CONFIG_THERMAL_GOV_USER_SPACE=y
-CONFIG_CPU_THERMAL=y
+CONFIG_TI_SOC_THERMAL=y
+CONFIG_OMAP4_THERMAL=y
+CONFIG_OMAP5_THERMAL=y
+CONFIG_DRA752_THERMAL=y
+CONFIG_WATCHDOG=y
 CONFIG_OMAP_WATCHDOG=y
 CONFIG_TWL4030_WATCHDOG=y
+CONFIG_MFD_PALMAS=y
 CONFIG_MFD_TPS65217=y
 CONFIG_MFD_TPS65910=y
 CONFIG_TWL6040_CORE=y
-CONFIG_REGULATOR_TWL4030=y
+CONFIG_REGULATOR_PALMAS=y
 CONFIG_REGULATOR_TPS65023=y
 CONFIG_REGULATOR_TPS6507X=y
 CONFIG_REGULATOR_TPS65217=y
 CONFIG_REGULATOR_TPS65910=y
+CONFIG_REGULATOR_TWL4030=y
 CONFIG_FB=y
 CONFIG_FIRMWARE_EDID=y
 CONFIG_FB_MODE_HELPERS=y
 CONFIG_FB_TILEBLITTING=y
-CONFIG_FB_OMAP_LCD_VGA=y
 CONFIG_OMAP2_DSS=m
-CONFIG_OMAP2_DSS_RFBI=y
 CONFIG_OMAP2_DSS_SDI=y
 CONFIG_OMAP2_DSS_DSI=y
 CONFIG_FB_OMAP2=m
@@ -194,12 +195,8 @@ CONFIG_DISPLAY_PANEL_DPI=m
 CONFIG_BACKLIGHT_LCD_SUPPORT=y
 CONFIG_LCD_CLASS_DEVICE=y
 CONFIG_LCD_PLATFORM=y
-CONFIG_DISPLAY_SUPPORT=y
 CONFIG_FRAMEBUFFER_CONSOLE=y
 CONFIG_FRAMEBUFFER_CONSOLE_ROTATION=y
-CONFIG_FONTS=y
-CONFIG_FONT_8x8=y
-CONFIG_FONT_8x16=y
 CONFIG_LOGO=y
 CONFIG_SOUND=m
 CONFIG_SND=m
@@ -216,14 +213,14 @@ CONFIG_SND_OMAP_SOC_OMAP3_PANDORA=m
 CONFIG_USB=y
 CONFIG_USB_DEBUG=y
 CONFIG_USB_ANNOUNCE_NEW_DEVICES=y
-CONFIG_USB_DEVICEFS=y
 CONFIG_USB_MON=y
 CONFIG_USB_WDM=y
 CONFIG_USB_STORAGE=y
-CONFIG_USB_LIBUSUAL=y
+CONFIG_USB_DWC3=m
 CONFIG_USB_TEST=y
-CONFIG_USB_PHY=y
 CONFIG_NOP_USB_XCEIV=y
+CONFIG_OMAP_USB2=y
+CONFIG_OMAP_USB3=y
 CONFIG_USB_GADGET=y
 CONFIG_USB_GADGET_DEBUG=y
 CONFIG_USB_GADGET_DEBUG_FILES=y
@@ -232,7 +229,6 @@ CONFIG_USB_ZERO=m
 CONFIG_MMC=y
 CONFIG_MMC_UNSAFE_RESUME=y
 CONFIG_SDIO_UART=y
-CONFIG_MMC_ARMMMCI=y
 CONFIG_MMC_OMAP=y
 CONFIG_MMC_OMAP_HS=y
 CONFIG_NEW_LEDS=y
@@ -252,11 +248,8 @@ CONFIG_RTC_DRV_OMAP=y
 CONFIG_DMADEVICES=y
 CONFIG_TI_EDMA=y
 CONFIG_DMA_OMAP=y
-CONFIG_TI_SOC_THERMAL=y
-CONFIG_TI_THERMAL=y
-CONFIG_OMAP4_THERMAL=y
-CONFIG_OMAP5_THERMAL=y
-CONFIG_DRA752_THERMAL=y
+CONFIG_EXTCON=y
+CONFIG_EXTCON_PALMAS=y
 CONFIG_EXT2_FS=y
 CONFIG_EXT3_FS=y
 # CONFIG_EXT3_FS_XATTR is not set
@@ -275,23 +268,18 @@ CONFIG_JFFS2_RUBIN=y
 CONFIG_UBIFS_FS=y
 CONFIG_CRAMFS=y
 CONFIG_NFS_FS=y
-CONFIG_NFS_V3=y
 CONFIG_NFS_V3_ACL=y
 CONFIG_NFS_V4=y
 CONFIG_ROOT_NFS=y
-CONFIG_PARTITION_ADVANCED=y
 CONFIG_NLS_CODEPAGE_437=y
 CONFIG_NLS_ISO8859_1=y
 CONFIG_PRINTK_TIME=y
+CONFIG_DEBUG_INFO=y
 CONFIG_MAGIC_SYSRQ=y
-CONFIG_DEBUG_KERNEL=y
 CONFIG_SCHEDSTATS=y
 CONFIG_TIMER_STATS=y
 CONFIG_PROVE_LOCKING=y
-CONFIG_DEBUG_SPINLOCK_SLEEP=y
 # CONFIG_DEBUG_BUGVERBOSE is not set
-CONFIG_DEBUG_INFO=y
-# CONFIG_RCU_CPU_STALL_DETECTOR is not set
 CONFIG_SECURITY=y
 CONFIG_CRYPTO_MICHAEL_MIC=y
 # CONFIG_CRYPTO_ANSI_CPRNG is not set
@@ -300,9 +288,6 @@ CONFIG_CRC_T10DIF=y
 CONFIG_CRC_ITU_T=y
 CONFIG_CRC7=y
 CONFIG_LIBCRC32C=y
-CONFIG_SOC_OMAP5=y
-CONFIG_TI_DAVINCI_MDIO=y
-CONFIG_TI_DAVINCI_CPDMA=y
-CONFIG_TI_CPSW=y
-CONFIG_AT803X_PHY=y
-CONFIG_SOC_DRA7XX=y
+CONFIG_FONTS=y
+CONFIG_FONT_8x8=y
+CONFIG_FONT_8x16=y

arch/arm/mach-omap2/Kconfig

@@ -94,6 +94,7 @@ config ARCH_OMAP2PLUS
 	select GENERIC_CLOCKEVENTS
 	select GENERIC_IRQ_CHIP
 	select HAVE_CLK
+	select MACH_OMAP_GENERIC
 	select OMAP_DM_TIMER
 	select PINCTRL
 	select PROC_DEVICETREE if PROC_FS
@@ -187,16 +188,11 @@ config OMAP_PACKAGE_CUS
 config OMAP_PACKAGE_CBP
        bool
 
-comment "OMAP Board Type"
+comment "OMAP Legacy Platform Data Board Type"
 	depends on ARCH_OMAP2PLUS
 
 config MACH_OMAP_GENERIC
-	bool "Generic OMAP2+ board"
-	depends on ARCH_OMAP2PLUS
-	default y
-	help
-	  Support for generic TI OMAP2+ boards using Flattened Device Tree.
-	  More information at Documentation/devicetree
+	bool
 
 config MACH_OMAP2_TUSB6010
 	bool

arch/arm/mach-omap2/Makefile

@@ -233,7 +233,7 @@ obj-y					+= drm.o
 endif
 
 # Specific board support
-obj-$(CONFIG_MACH_OMAP_GENERIC)		+= board-generic.o
+obj-$(CONFIG_MACH_OMAP_GENERIC)		+= board-generic.o pdata-quirks.o
 obj-$(CONFIG_MACH_OMAP_H4)		+= board-h4.o
 obj-$(CONFIG_MACH_OMAP_2430SDP)		+= board-2430sdp.o
 obj-$(CONFIG_MACH_OMAP3_BEAGLE)		+= board-omap3beagle.o

arch/arm/mach-omap2/board-generic.c

@@ -15,13 +15,10 @@
 #include <linux/of_irq.h>
 #include <linux/of_platform.h>
 #include <linux/irqdomain.h>
-#include <linux/clk.h>
 
 #include <asm/mach/arch.h>
 
 #include "common.h"
-#include "common-board-devices.h"
-#include "dss-common.h"
 
 #if !(defined(CONFIG_ARCH_OMAP2) || defined(CONFIG_ARCH_OMAP3))
 #define intc_of_init	NULL
@@ -36,40 +33,9 @@ static struct of_device_id omap_dt_match_table[] __initdata = {
 	{ }
 };
 
-/*
- * Create alias for USB host PHY clock.
- * Remove this when clock phandle can be provided via DT
- */
-static void __init legacy_init_ehci_clk(char *clkname)
-{
-	int ret;
-
-	ret = clk_add_alias("main_clk", NULL, clkname, NULL);
-	if (ret) {
-		pr_err("%s:Failed to add main_clk alias to %s :%d\n",
-						__func__, clkname, ret);
-	}
-}
-
 static void __init omap_generic_init(void)
 {
-	omap_sdrc_init(NULL, NULL);
-
-	of_platform_populate(NULL, omap_dt_match_table, NULL, NULL);
-
-	/*
-	 * HACK: call display setup code for selected boards to enable omapdss.
-	 * This will be removed when omapdss supports DT.
-	 */
-	if (of_machine_is_compatible("ti,omap4-panda")) {
-		omap4_panda_display_init_of();
-		legacy_init_ehci_clk("auxclk3_ck");
-
-	}
-	else if (of_machine_is_compatible("ti,omap4-sdp"))
-		omap_4430sdp_display_init_of();
-	else if (of_machine_is_compatible("ti,omap5-uevm"))
-		legacy_init_ehci_clk("auxclk1_ck");
+	pdata_quirks_init(omap_dt_match_table);
 }
 
 #ifdef CONFIG_SOC_OMAP2420

arch/arm/mach-omap2/board-igep0020.c

@@ -43,6 +43,7 @@
 #include "board-flash.h"
 #include "control.h"
 #include "gpmc-onenand.h"
+#include "dss-common.h"
 
 #define IGEP2_SMSC911X_CS       5
 #define IGEP2_SMSC911X_GPIO     176
@@ -50,7 +51,6 @@
 #define IGEP2_GPIO_LED0_GREEN   26
 #define IGEP2_GPIO_LED0_RED     27
 #define IGEP2_GPIO_LED1_RED     28
-#define IGEP2_GPIO_DVI_PUP      170
 
 #define IGEP2_RB_GPIO_WIFI_NPD     94
 #define IGEP2_RB_GPIO_WIFI_NRESET  95
@@ -429,41 +429,6 @@ static struct twl4030_gpio_platform_data igep_twl4030_gpio_pdata = {
 	.setup		= igep_twl_gpio_setup,
 };
 
-static struct connector_dvi_platform_data omap3stalker_dvi_connector_pdata = {
-	.name                   = "dvi",
-	.source                 = "tfp410.0",
-	.i2c_bus_num            = 3,
-};
-
-static struct platform_device omap3stalker_dvi_connector_device = {
-	.name                   = "connector-dvi",
-	.id                     = 0,
-	.dev.platform_data      = &omap3stalker_dvi_connector_pdata,
-};
-
-static struct encoder_tfp410_platform_data omap3stalker_tfp410_pdata = {
-	.name                   = "tfp410.0",
-	.source                 = "dpi.0",
-	.data_lines             = 24,
-	.power_down_gpio        = IGEP2_GPIO_DVI_PUP,
-};
-
-static struct platform_device omap3stalker_tfp410_device = {
-	.name                   = "tfp410",
-	.id                     = 0,
-	.dev.platform_data      = &omap3stalker_tfp410_pdata,
-};
-
-static struct omap_dss_board_info igep2_dss_data = {
-	.default_display_name = "dvi",
-};
-
-static struct platform_device *igep_devices[] __initdata = {
-	&igep_vwlan_device,
-	&omap3stalker_tfp410_device,
-	&omap3stalker_dvi_connector_device,
-};
-
 static int igep2_keymap[] = {
 	KEY(0, 0, KEY_LEFT),
 	KEY(0, 1, KEY_RIGHT),
@@ -663,7 +628,8 @@ static void __init igep_init(void)
 
 	/* Register I2C busses and drivers */
 	igep_i2c_init();
-	platform_add_devices(igep_devices, ARRAY_SIZE(igep_devices));
+	platform_device_register(&igep_vwlan_device);
+	omap3_igep2_display_init_of();
 	omap_serial_init();
 	omap_sdrc_init(m65kxxxxam_sdrc_params,
 				  m65kxxxxam_sdrc_params);
@@ -681,7 +647,6 @@ static void __init igep_init(void)
 	igep_wlan_bt_init();
 
 	if (machine_is_igep0020()) {
-		omap_display_init(&igep2_dss_data);
 		igep2_init_smsc911x();
 		usbhs_init_phys(igep2_phy_data, ARRAY_SIZE(igep2_phy_data));
 		usbhs_init(&igep2_usbhs_bdata);

arch/arm/mach-omap2/common.h

@@ -288,6 +288,9 @@ static inline void omap4_cpu_resume(void)
 
 #endif
 
+void pdata_quirks_init(struct of_device_id *);
+void omap_pcs_legacy_init(int irq, void (*rearm)(void));
+
 struct omap_sdrc_params;
 extern void omap_sdrc_init(struct omap_sdrc_params *sdrc_cs0,
 				      struct omap_sdrc_params *sdrc_cs1);

arch/arm/mach-omap2/devices.c

@@ -19,7 +19,6 @@
 #include <linux/of.h>
 #include <linux/pinctrl/machine.h>
 #include <linux/platform_data/omap4-keypad.h>
-#include <linux/wl12xx.h>
 #include <linux/platform_data/mailbox-omap.h>
 
 #include <asm/mach-types.h>
@@ -475,40 +474,6 @@ static void omap_init_vout(void)
 static inline void omap_init_vout(void) {}
 #endif
 
-#if IS_ENABLED(CONFIG_WL12XX)
-
-static struct wl12xx_platform_data wl12xx __initdata;
-
-void __init omap_init_wl12xx_of(void)
-{
-	int ret;
-
-	if (!of_have_populated_dt())
-		return;
-
-	if (of_machine_is_compatible("ti,omap4-sdp")) {
-		wl12xx.board_ref_clock = WL12XX_REFCLOCK_26;
-		wl12xx.board_tcxo_clock = WL12XX_TCXOCLOCK_26;
-		wl12xx.irq = gpio_to_irq(53);
-	} else if (of_machine_is_compatible("ti,omap4-panda")) {
-		wl12xx.board_ref_clock = WL12XX_REFCLOCK_38;
-		wl12xx.irq = gpio_to_irq(53);
-	} else {
-		return;
-	}
-
-	ret = wl12xx_set_platform_data(&wl12xx);
-	if (ret) {
-		pr_err("error setting wl12xx data: %d\n", ret);
-		return;
-	}
-}
-#else
-static inline void omap_init_wl12xx_of(void)
-{
-}
-#endif
-
 /*-------------------------------------------------------------------------*/
 
 static int __init omap2_init_devices(void)
@@ -531,9 +496,6 @@ static int __init omap2_init_devices(void)
 		omap_init_sham();
 		omap_init_aes();
 		omap_init_rng();
-	} else {
-		/* These can be removed when bindings are done */
-		omap_init_wl12xx_of();
 	}
 	omap_init_sti();
 	omap_init_vout();

arch/arm/mach-omap2/dss-common.c

@@ -213,3 +213,47 @@ void __init omap_4430sdp_display_init_of(void)
 	platform_device_register(&sdp4430_tpd_device);
 	platform_device_register(&sdp4430_hdmi_connector_device);
 }
+
+
+/* OMAP3 IGEPv2 data */
+
+#define IGEP2_DVI_TFP410_POWER_DOWN_GPIO	170
+
+/* DVI Connector */
+static struct connector_dvi_platform_data omap3_igep2_dvi_connector_pdata = {
+	.name                   = "dvi",
+	.source                 = "tfp410.0",
+	.i2c_bus_num            = 3,
+};
+
+static struct platform_device omap3_igep2_dvi_connector_device = {
+	.name                   = "connector-dvi",
+	.id                     = 0,
+	.dev.platform_data      = &omap3_igep2_dvi_connector_pdata,
+};
+
+/* TFP410 DPI-to-DVI chip */
+static struct encoder_tfp410_platform_data omap3_igep2_tfp410_pdata = {
+	.name                   = "tfp410.0",
+	.source                 = "dpi.0",
+	.data_lines             = 24,
+	.power_down_gpio        = IGEP2_DVI_TFP410_POWER_DOWN_GPIO,
+};
+
+static struct platform_device omap3_igep2_tfp410_device = {
+	.name                   = "tfp410",
+	.id                     = 0,
+	.dev.platform_data      = &omap3_igep2_tfp410_pdata,
+};
+
+static struct omap_dss_board_info igep2_dss_data = {
+	.default_display_name = "dvi",
+};
+
+void __init omap3_igep2_display_init_of(void)
+{
+	omap_display_init(&igep2_dss_data);
+
+	platform_device_register(&omap3_igep2_tfp410_device);
+	platform_device_register(&omap3_igep2_dvi_connector_device);
+}

arch/arm/mach-omap2/dss-common.h

@@ -8,5 +8,6 @@
 
 void __init omap4_panda_display_init_of(void);
 void __init omap_4430sdp_display_init_of(void);
+void __init omap3_igep2_display_init_of(void);
 
 #endif

arch/arm/mach-omap2/gpmc.c

@@ -1521,6 +1521,42 @@ static int gpmc_probe_generic_child(struct platform_device *pdev,
 	return ret;
 }
 
+/*
+ * REVISIT: Add timing support from slls644g.pdf
+ */
+static int gpmc_probe_8250(struct platform_device *pdev,
+				struct device_node *child)
+{
+	struct resource res;
+	unsigned long base;
+	int ret, cs;
+
+	if (of_property_read_u32(child, "reg", &cs) < 0) {
+		dev_err(&pdev->dev, "%s has no 'reg' property\n",
+			child->full_name);
+		return -ENODEV;
+	}
+
+	if (of_address_to_resource(child, 0, &res) < 0) {
+		dev_err(&pdev->dev, "%s has malformed 'reg' property\n",
+			child->full_name);
+		return -ENODEV;
+	}
+
+	ret = gpmc_cs_request(cs, resource_size(&res), &base);
+	if (ret < 0) {
+		dev_err(&pdev->dev, "cannot request GPMC CS %d\n", cs);
+		return ret;
+	}
+
+	if (of_platform_device_create(child, NULL, &pdev->dev))
+		return 0;
+
+	dev_err(&pdev->dev, "failed to create gpmc child %s\n", child->name);
+
+	return -ENODEV;
+}
+
 static int gpmc_probe_dt(struct platform_device *pdev)
 {
 	int ret;
@@ -1564,6 +1600,8 @@ static int gpmc_probe_dt(struct platform_device *pdev)
 		else if (of_node_cmp(child->name, "ethernet") == 0 ||
 			 of_node_cmp(child->name, "nor") == 0)
 			ret = gpmc_probe_generic_child(pdev, child);
+		else if (of_node_cmp(child->name, "8250") == 0)
+			ret = gpmc_probe_8250(pdev, child);
 
 		if (WARN(ret < 0, "%s: probing gpmc child %s failed\n",
 			 __func__, child->full_name))

arch/arm/mach-omap2/mux.c

@@ -811,6 +811,12 @@ int __init omap_mux_late_init(void)
 		}
 	}
 
+	omap_mux_dbg_init();
+
+	/* see pinctrl-single-omap for the wake-up interrupt handling */
+	if (of_have_populated_dt())
+		return 0;
+
 	ret = request_irq(omap_prcm_event_to_irq("io"),
 		omap_hwmod_mux_handle_irq, IRQF_SHARED | IRQF_NO_SUSPEND,
 			"hwmod_io", omap_mux_late_init);
@@ -818,8 +824,6 @@ int __init omap_mux_late_init(void)
 	if (ret)
 		pr_warning("mux: Failed to setup hwmod io irq %d\n", ret);
 
-	omap_mux_dbg_init();
-
 	return 0;
 }
 

arch/arm/mach-omap2/pdata-quirks.c

+/*
+ * Legacy platform_data quirks
+ *
+ * Copyright (C) 2013 Texas Instruments
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#include <linux/clk.h>
+#include <linux/gpio.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/of_platform.h>
+#include <linux/wl12xx.h>
+
+#include <linux/platform_data/pinctrl-single.h>
+
+#include "common.h"
+#include "common-board-devices.h"
+#include "dss-common.h"
+#include "control.h"
+
+struct pdata_init {
+	const char *compatible;
+	void (*fn)(void);
+};
+
+/*
+ * Create alias for USB host PHY clock.
+ * Remove this when clock phandle can be provided via DT
+ */
+static void __init __used legacy_init_ehci_clk(char *clkname)
+{
+	int ret;
+
+	ret = clk_add_alias("main_clk", NULL, clkname, NULL);
+	if (ret)
+		pr_err("%s:Failed to add main_clk alias to %s :%d\n",
+		       __func__, clkname, ret);
+}
+
+#if IS_ENABLED(CONFIG_WL12XX)
+
+static struct wl12xx_platform_data wl12xx __initdata;
+
+static void __init __used legacy_init_wl12xx(unsigned ref_clock,
+					     unsigned tcxo_clock,
+					     int gpio)
+{
+	int res;
+
+	wl12xx.board_ref_clock = ref_clock;
+	wl12xx.board_tcxo_clock = tcxo_clock;
+	wl12xx.irq = gpio_to_irq(gpio);
+
+	res = wl12xx_set_platform_data(&wl12xx);
+	if (res) {
+		pr_err("error setting wl12xx data: %d\n", res);
+		return;
+	}
+}
+#else
+static inline void legacy_init_wl12xx(unsigned ref_clock,
+				      unsigned tcxo_clock,
+				      int gpio)
+{
+}
+#endif
+
+#ifdef CONFIG_ARCH_OMAP3
+static void __init hsmmc2_internal_input_clk(void)
+{
+	u32 reg;
+
+	reg = omap_ctrl_readl(OMAP343X_CONTROL_DEVCONF1);
+	reg |= OMAP2_MMCSDIO2ADPCLKISEL;
+	omap_ctrl_writel(reg, OMAP343X_CONTROL_DEVCONF1);
+}
+
+static void __init omap3_igep0020_legacy_init(void)
+{
+	omap3_igep2_display_init_of();
+}
+
+static void __init omap3_evm_legacy_init(void)
+{
+	legacy_init_wl12xx(WL12XX_REFCLOCK_38, 0, 149);
+}
+
+static void __init omap3_zoom_legacy_init(void)
+{
+	legacy_init_wl12xx(WL12XX_REFCLOCK_26, 0, 162);
+}
+#endif /* CONFIG_ARCH_OMAP3 */
+
+#ifdef CONFIG_ARCH_OMAP4
+static void __init omap4_sdp_legacy_init(void)
+{
+	omap_4430sdp_display_init_of();
+	legacy_init_wl12xx(WL12XX_REFCLOCK_26,
+			   WL12XX_TCXOCLOCK_26, 53);
+}
+
+static void __init omap4_panda_legacy_init(void)
+{
+	omap4_panda_display_init_of();
+	legacy_init_ehci_clk("auxclk3_ck");
+	legacy_init_wl12xx(WL12XX_REFCLOCK_38, 0, 53);
+}
+#endif
+
+#ifdef CONFIG_SOC_OMAP5
+static void __init omap5_uevm_legacy_init(void)
+{
+	legacy_init_ehci_clk("auxclk1_ck");
+}
+#endif
+
+static struct pcs_pdata pcs_pdata;
+
+void omap_pcs_legacy_init(int irq, void (*rearm)(void))
+{
+	pcs_pdata.irq = irq;
+	pcs_pdata.rearm = rearm;
+}
+
+struct of_dev_auxdata omap_auxdata_lookup[] __initdata = {
+#ifdef CONFIG_ARCH_OMAP3
+	OF_DEV_AUXDATA("ti,omap3-padconf", 0x48002030, "48002030.pinmux", &pcs_pdata),
+	OF_DEV_AUXDATA("ti,omap3-padconf", 0x48002a00, "48002a00.pinmux", &pcs_pdata),
+#endif
+#ifdef CONFIG_ARCH_OMAP4
+	OF_DEV_AUXDATA("ti,omap4-padconf", 0x4a100040, "4a100040.pinmux", &pcs_pdata),
+	OF_DEV_AUXDATA("ti,omap4-padconf", 0x4a31e040, "4a31e040.pinmux", &pcs_pdata),
+#endif
+	{ /* sentinel */ },
+};
+
+static struct pdata_init pdata_quirks[] __initdata = {
+#ifdef CONFIG_ARCH_OMAP3
+	{ "nokia,omap3-n9", hsmmc2_internal_input_clk, },
+	{ "nokia,omap3-n950", hsmmc2_internal_input_clk, },
+	{ "isee,omap3-igep0020", omap3_igep0020_legacy_init, },
+	{ "ti,omap3-evm-37xx", omap3_evm_legacy_init, },
+	{ "ti,omap3-zoom3", omap3_zoom_legacy_init, },
+#endif
+#ifdef CONFIG_ARCH_OMAP4
+	{ "ti,omap4-sdp", omap4_sdp_legacy_init, },
+	{ "ti,omap4-panda", omap4_panda_legacy_init, },
+#endif
+#ifdef CONFIG_SOC_OMAP5
+	{ "ti,omap5-uevm", omap5_uevm_legacy_init, },
+#endif
+	{ /* sentinel */ },
+};
+
+void __init pdata_quirks_init(struct of_device_id *omap_dt_match_table)
+{
+	struct pdata_init *quirks = pdata_quirks;
+
+	omap_sdrc_init(NULL, NULL);
+	of_platform_populate(NULL, omap_dt_match_table,
+			     omap_auxdata_lookup, NULL);
+
+	while (quirks->compatible) {
+		if (of_machine_is_compatible(quirks->compatible)) {
+			if (quirks->fn)
+				quirks->fn();
+			break;
+		}
+		quirks++;
+	}
+}

arch/arm/mach-omap2/prm3xxx.h

@@ -144,7 +144,13 @@ extern u32 omap3_prm_vcvp_read(u8 offset);
 extern void omap3_prm_vcvp_write(u32 val, u8 offset);
 extern u32 omap3_prm_vcvp_rmw(u32 mask, u32 bits, u8 offset);
 
-extern void omap3xxx_prm_reconfigure_io_chain(void);
+#ifdef CONFIG_ARCH_OMAP3
+void omap3xxx_prm_reconfigure_io_chain(void);
+#else
+static inline void omap3xxx_prm_reconfigure_io_chain(void)
+{
+}
+#endif
 
 /* PRM interrupt-related functions */
 extern void omap3xxx_prm_read_pending_irqs(unsigned long *events);

arch/arm/mach-omap2/prm44xx_54xx.h

@@ -42,7 +42,13 @@ extern u32 omap4_prm_vcvp_read(u8 offset);
 extern void omap4_prm_vcvp_write(u32 val, u8 offset);
 extern u32 omap4_prm_vcvp_rmw(u32 mask, u32 bits, u8 offset);
 
-extern void omap44xx_prm_reconfigure_io_chain(void);
+#if defined(CONFIG_ARCH_OMAP4) || defined(CONFIG_SOC_OMAP5)
+void omap44xx_prm_reconfigure_io_chain(void);
+#else
+static inline void omap44xx_prm_reconfigure_io_chain(void)
+{
+}
+#endif
 
 /* PRM interrupt-related functions */
 extern void omap44xx_prm_read_pending_irqs(unsigned long *events);

arch/arm/mach-omap2/prm_common.c

@@ -24,6 +24,7 @@
 #include <linux/interrupt.h>
 #include <linux/slab.h>
 
+#include "soc.h"
 #include "prm2xxx_3xxx.h"
 #include "prm2xxx.h"
 #include "prm3xxx.h"
@@ -322,6 +323,16 @@ int omap_prcm_register_chain_handler(struct omap_prcm_irq_setup *irq_setup)
 		prcm_irq_chips[i] = gc;
 	}
 
+	if (of_have_populated_dt()) {
+		int irq = omap_prcm_event_to_irq("io");
+		if (cpu_is_omap34xx())
+			omap_pcs_legacy_init(irq,
+				omap3xxx_prm_reconfigure_io_chain);
+		else
+			omap_pcs_legacy_init(irq,
+				omap44xx_prm_reconfigure_io_chain);
+	}
+
 	return 0;
 
 err:

include/dt-bindings/pinctrl/dra.h

+/*
+ * This header provides constants for DRA pinctrl bindings.
+ *
+ * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/
+ * Author: Rajendra Nayak <rnayak@ti.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef _DT_BINDINGS_PINCTRL_DRA_H
+#define _DT_BINDINGS_PINCTRL_DRA_H
+
+/* DRA7 mux mode options for each pin. See TRM for options */
+#define MUX_MODE0	0x0
+#define MUX_MODE1	0x1
+#define MUX_MODE2	0x2
+#define MUX_MODE3	0x3
+#define MUX_MODE4	0x4
+#define MUX_MODE5	0x5
+#define MUX_MODE6	0x6
+#define MUX_MODE7	0x7
+#define MUX_MODE8	0x8
+#define MUX_MODE9	0x9
+#define MUX_MODE10	0xa
+#define MUX_MODE11	0xb
+#define MUX_MODE12	0xc
+#define MUX_MODE13	0xd
+#define MUX_MODE14	0xe
+#define MUX_MODE15	0xf
+
+#define PULL_ENA		(1 << 16)
+#define PULL_UP			(1 << 17)
+#define INPUT_EN		(1 << 18)
+#define SLEWCONTROL		(1 << 19)
+#define WAKEUP_EN		(1 << 24)
+#define WAKEUP_EVENT		(1 << 25)
+
+/* Active pin states */
+#define PIN_OUTPUT		0
+#define PIN_OUTPUT_PULLUP	(PIN_OUTPUT | PULL_ENA | PULL_UP)
+#define PIN_OUTPUT_PULLDOWN	(PIN_OUTPUT | PULL_ENA)
+#define PIN_INPUT		INPUT_EN
+#define PIN_INPUT_SLEW		(INPUT_EN | SLEWCONTROL)
+#define PIN_INPUT_PULLUP	(PULL_ENA | INPUT_EN | PULL_UP)
+#define PIN_INPUT_PULLDOWN	(PULL_ENA | INPUT_EN)
+
+#endif
+

include/linux/platform_data/pinctrl-single.h

+/**
+ * irq:		optional wake-up interrupt
+ * rearm:	optional soc specific rearm function
+ *
+ * Note that the irq and rearm setup should come from device
+ * tree except for omap where there are still some dependencies
+ * to the legacy PRM code.
+ */
+struct pcs_pdata {
+	int irq;
+	void (*rearm)(void);
+};