Commit f6da2842 authored by Shobhit Kumar's avatar Shobhit Kumar Committed by Daniel Vetter

drm/i915: Parametrize the dphy and other spec specific parameters

The values of these parameters will be different for differnet panel
based on dsi rate, lane count, etc. Remove the hardcodings and make
these as parameters whch will be initialized in panel specific
sub-encoder implementaion.

This will also form groundwork for planned generic panel sub-encoder
implemntation based on VBT design enhancments to support multiple panels

v2: Mask away the port_bits before use
Signed-off-by: default avatarShobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: default avatarJani Nikula <jani.nikula@intel.com>
Signed-off-by: default avatarDaniel Vetter <daniel.vetter@ffwll.ch>
parent a4a593be
......@@ -157,7 +157,8 @@ static void intel_dsi_enable(struct intel_encoder *encoder)
msleep(100);
/* assert ip_tg_enable signal */
temp = I915_READ(MIPI_PORT_CTRL(pipe));
temp = I915_READ(MIPI_PORT_CTRL(pipe)) & ~LANE_CONFIGURATION_MASK;
temp = temp | intel_dsi->port_bits;
I915_WRITE(MIPI_PORT_CTRL(pipe), temp | DPI_ENABLE);
POSTING_READ(MIPI_PORT_CTRL(pipe));
}
......@@ -391,11 +392,7 @@ static void intel_dsi_mode_set(struct intel_encoder *intel_encoder)
I915_WRITE(MIPI_INTR_STAT(pipe), 0xffffffff);
I915_WRITE(MIPI_INTR_EN(pipe), 0xffffffff);
I915_WRITE(MIPI_DPHY_PARAM(pipe),
0x3c << EXIT_ZERO_COUNT_SHIFT |
0x1f << TRAIL_COUNT_SHIFT |
0xc5 << CLK_ZERO_COUNT_SHIFT |
0x1f << PREPARE_COUNT_SHIFT);
I915_WRITE(MIPI_DPHY_PARAM(pipe), intel_dsi->dphy_reg);
I915_WRITE(MIPI_DPI_RESOLUTION(pipe),
adjusted_mode->vdisplay << VERTICAL_ADDRESS_SHIFT |
......@@ -443,9 +440,9 @@ static void intel_dsi_mode_set(struct intel_encoder *intel_encoder)
adjusted_mode->htotal,
bpp, intel_dsi->lane_count) + 1);
}
I915_WRITE(MIPI_LP_RX_TIMEOUT(pipe), 8309); /* max */
I915_WRITE(MIPI_TURN_AROUND_TIMEOUT(pipe), 0x14); /* max */
I915_WRITE(MIPI_DEVICE_RESET_TIMER(pipe), 0xffff); /* max */
I915_WRITE(MIPI_LP_RX_TIMEOUT(pipe), intel_dsi->lp_rx_timeout);
I915_WRITE(MIPI_TURN_AROUND_TIMEOUT(pipe), intel_dsi->turn_arnd_val);
I915_WRITE(MIPI_DEVICE_RESET_TIMER(pipe), intel_dsi->rst_timer_val);
/* dphy stuff */
......@@ -460,28 +457,30 @@ static void intel_dsi_mode_set(struct intel_encoder *intel_encoder)
*
* XXX: write MIPI_STOP_STATE_STALL?
*/
I915_WRITE(MIPI_HIGH_LOW_SWITCH_COUNT(pipe), 0x46);
I915_WRITE(MIPI_HIGH_LOW_SWITCH_COUNT(pipe),
intel_dsi->hs_to_lp_count);
/* XXX: low power clock equivalence in terms of byte clock. the number
* of byte clocks occupied in one low power clock. based on txbyteclkhs
* and txclkesc. txclkesc time / txbyteclk time * (105 +
* MIPI_STOP_STATE_STALL) / 105.???
*/
I915_WRITE(MIPI_LP_BYTECLK(pipe), 4);
I915_WRITE(MIPI_LP_BYTECLK(pipe), intel_dsi->lp_byte_clk);
/* the bw essential for transmitting 16 long packets containing 252
* bytes meant for dcs write memory command is programmed in this
* register in terms of byte clocks. based on dsi transfer rate and the
* number of lanes configured the time taken to transmit 16 long packets
* in a dsi stream varies. */
I915_WRITE(MIPI_DBI_BW_CTRL(pipe), 0x820);
I915_WRITE(MIPI_DBI_BW_CTRL(pipe), intel_dsi->bw_timer);
I915_WRITE(MIPI_CLK_LANE_SWITCH_TIME_CNT(pipe),
0xa << LP_HS_SSW_CNT_SHIFT |
0x14 << HS_LP_PWR_SW_CNT_SHIFT);
intel_dsi->clk_lp_to_hs_count << LP_HS_SSW_CNT_SHIFT |
intel_dsi->clk_hs_to_lp_count << HS_LP_PWR_SW_CNT_SHIFT);
if (is_vid_mode(intel_dsi))
I915_WRITE(MIPI_VIDEO_MODE_FORMAT(pipe),
intel_dsi->video_frmt_cfg_bits |
intel_dsi->video_mode_format);
}
......
......@@ -96,6 +96,20 @@ struct intel_dsi {
/* eot for MIPI_EOT_DISABLE register */
u32 eot_disable;
u32 port_bits;
u32 bw_timer;
u32 dphy_reg;
u32 video_frmt_cfg_bits;
u16 lp_byte_clk;
/* timeouts in byte clocks */
u16 lp_rx_timeout;
u16 turn_arnd_val;
u16 rst_timer_val;
u16 hs_to_lp_count;
u16 clk_lp_to_hs_count;
u16 clk_hs_to_lp_count;
};
static inline struct intel_dsi *enc_to_intel_dsi(struct drm_encoder *encoder)
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment