Merge branch 'for-upstream' of...

Merge branch 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next

Johan Hedberg says:

====================
pull request: bluetooth-next 2019-07-07

Here's the main bluetooth-next pull request for 5.3:

 - Added support for new devices from Qualcomm, Realtek and Broadcom and
   MediaTek
 - Various fixes to 6LoWPAN
 - Fix L2CAP PSM namespace separation for LE & BR/EDR
 - Fix behavior with Microsoft Surface Precision Mouse
 - Added support for LE Ping feature
 - Fix L2CAP Disconnect response handling if received in wrong state

Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Documentation/devicetree/bindings/net/marvell-bluetooth.txt

+Marvell Bluetooth Chips
+-----------------------
+
+This documents the binding structure and common properties for serial
+attached Marvell Bluetooth devices. The following chips are included in
+this binding:
+
+* Marvell 88W8897 Bluetooth devices
+
+Required properties:
+ - compatible: should be:
+    "mrvl,88w8897"
+
+Optional properties:
+None so far
+
+Example:
+
+&serial0 {
+	compatible = "ns16550a";
+	...
+	bluetooth {
+		compatible = "mrvl,88w8897";
+	};
+};

Documentation/devicetree/bindings/net/mediatek-bluetooth.txt

@@ -50,16 +50,33 @@ Required properties:
 		  "mediatek,mt7663u-bluetooth": for MT7663U device
 		  "mediatek,mt7668u-bluetooth": for MT7668U device
 - vcc-supply:	Main voltage regulator
+
+If the pin controller on the platform can support both pinmux and GPIO
+control such as the most of MediaTek platform. Please use below properties.
+
 - pinctrl-names: Should be "default", "runtime"
 - pinctrl-0: Should contain UART RXD low when the device is powered up to
 	     enter proper bootstrap mode.
 - pinctrl-1: Should contain UART mode pin ctrl
 
+Else, the pin controller on the platform only can support pinmux control and
+the GPIO control still has to rely on the dedicated GPIO controller such as
+a legacy MediaTek SoC, MT7621. Please use the below properties.
+
+- boot-gpios:	GPIO same to the pin as UART RXD and used to keep LOW when
+		the device is powered up to enter proper bootstrap mode when
+- pinctrl-names: Should be "default"
+- pinctrl-0: Should contain UART mode pin ctrl
+
 Optional properties:
 
 - reset-gpios:	GPIO used to reset the device whose initial state keeps low,
 		if the GPIO is missing, then board-level design should be
 		guaranteed.
+- clocks:	Should be the clock specifiers corresponding to the entry in
+		clock-names property. If the clock is missing, then board-level
+		design should be guaranteed.
+- clock-names:	Should contain "osc" entry for the external oscillator.
 - current-speed:  Current baud rate of the device whose defaults to 921600
 
 Example:

Documentation/devicetree/bindings/net/qualcomm-bluetooth.txt

@@ -17,6 +17,7 @@ Optional properties for compatible string qcom,qca6174-bt:
 
  - enable-gpios: gpio specifier used to enable chip
  - clocks: clock provided to the controller (SUSCLK_32KHZ)
+ - firmware-name: specify the name of nvm firmware to load
 
 Required properties for compatible string qcom,wcn399x-bt:
 
@@ -28,6 +29,7 @@ Required properties for compatible string qcom,wcn399x-bt:
 Optional properties for compatible string qcom,wcn399x-bt:
 
  - max-speed: see Documentation/devicetree/bindings/serial/slave-device.txt
+ - firmware-name: specify the name of nvm firmware to load
 
 Examples:
 
@@ -40,6 +42,7 @@ serial@7570000 {
 
 		enable-gpios = <&pm8994_gpios 19 GPIO_ACTIVE_HIGH>;
 		clocks = <&divclk4>;
+		firmware-name = "nvm_00440302.bin";
 	};
 };
 
@@ -52,5 +55,6 @@ serial@898000 {
 		vddrf-supply = <&vreg_l17a_1p3>;
 		vddch0-supply = <&vreg_l25a_3p3>;
 		max-speed = <3200000>;
+		firmware-name = "crnv21.bin";
 	};
 };

drivers/bluetooth/Kconfig

@@ -52,6 +52,17 @@ config BT_HCIBTUSB_BCM
 
 	  Say Y here to compile support for Broadcom protocol.
 
+config BT_HCIBTUSB_MTK
+	bool "MediaTek protocol support"
+	depends on BT_HCIBTUSB
+	default n
+	help
+	  The MediaTek protocol support enables firmware download
+	  support and chip initialization for MediaTek Bluetooth
+	  USB controllers.
+
+	  Say Y here to compile support for MediaTek protocol.
+
 config BT_HCIBTUSB_RTL
 	bool "Realtek protocol support"
 	depends on BT_HCIBTUSB
@@ -237,6 +248,7 @@ config BT_HCIUART_AG6XX
 config BT_HCIUART_MRVL
 	bool "Marvell protocol support"
 	depends on BT_HCIUART
+	depends on BT_HCIUART_SERDEV
 	select BT_HCIUART_H4
 	help
 	  Marvell is serial protocol for communication between Bluetooth

drivers/bluetooth/bpa10x.c

@@ -359,7 +359,8 @@ static int bpa10x_set_diag(struct hci_dev *hdev, bool enable)
 	return 0;
 }
 
-static int bpa10x_probe(struct usb_interface *intf, const struct usb_device_id *id)
+static int bpa10x_probe(struct usb_interface *intf,
+			const struct usb_device_id *id)
 {
 	struct bpa10x_data *data;
 	struct hci_dev *hdev;

drivers/bluetooth/btbcm.c

@@ -335,6 +335,7 @@ static const struct bcm_subver_table bcm_uart_subver_table[] = {
 	{ 0x230f, "BCM4356A2"	},	/* 001.003.015 */
 	{ 0x220e, "BCM20702A1"  },	/* 001.002.014 */
 	{ 0x4217, "BCM4329B1"   },	/* 002.002.023 */
+	{ 0x6106, "BCM4359C0"	},	/* 003.001.006 */
 	{ }
 };
 

drivers/bluetooth/btmtkuart.c

@@ -115,10 +115,12 @@ struct btmtk_hci_wmt_params {
 struct btmtkuart_dev {
 	struct hci_dev *hdev;
 	struct serdev_device *serdev;
-	struct clk *clk;
 
+	struct clk *clk;
+	struct clk *osc;
 	struct regulator *vcc;
 	struct gpio_desc *reset;
+	struct gpio_desc *boot;
 	struct pinctrl *pinctrl;
 	struct pinctrl_state *pins_runtime;
 	struct pinctrl_state *pins_boot;
@@ -911,6 +913,19 @@ static int btmtkuart_parse_dt(struct serdev_device *serdev)
 			return err;
 		}
 
+		bdev->osc = devm_clk_get_optional(&serdev->dev, "osc");
+		if (IS_ERR(bdev->osc)) {
+			err = PTR_ERR(bdev->osc);
+			return err;
+		}
+
+		bdev->boot = devm_gpiod_get_optional(&serdev->dev, "boot",
+						     GPIOD_OUT_LOW);
+		if (IS_ERR(bdev->boot)) {
+			err = PTR_ERR(bdev->boot);
+			return err;
+		}
+
 		bdev->pinctrl = devm_pinctrl_get(&serdev->dev);
 		if (IS_ERR(bdev->pinctrl)) {
 			err = PTR_ERR(bdev->pinctrl);
@@ -919,8 +934,10 @@ static int btmtkuart_parse_dt(struct serdev_device *serdev)
 
 		bdev->pins_boot = pinctrl_lookup_state(bdev->pinctrl,
 						       "default");
-		if (IS_ERR(bdev->pins_boot)) {
+		if (IS_ERR(bdev->pins_boot) && !bdev->boot) {
 			err = PTR_ERR(bdev->pins_boot);
+			dev_err(&serdev->dev,
+				"Should assign RXD to LOW at boot stage\n");
 			return err;
 		}
 
@@ -996,13 +1013,25 @@ static int btmtkuart_probe(struct serdev_device *serdev)
 	set_bit(HCI_QUIRK_NON_PERSISTENT_SETUP, &hdev->quirks);
 
 	if (btmtkuart_is_standalone(bdev)) {
-		/* Switch to the specific pin state for the booting requires */
-		pinctrl_select_state(bdev->pinctrl, bdev->pins_boot);
+		err = clk_prepare_enable(bdev->osc);
+		if (err < 0)
+			return err;
+
+		if (bdev->boot) {
+			gpiod_set_value_cansleep(bdev->boot, 1);
+		} else {
+			/* Switch to the specific pin state for the booting
+			 * requires.
+			 */
+			pinctrl_select_state(bdev->pinctrl, bdev->pins_boot);
+		}
 
 		/* Power on */
 		err = regulator_enable(bdev->vcc);
-		if (err < 0)
+		if (err < 0) {
+			clk_disable_unprepare(bdev->osc);
 			return err;
+		}
 
 		/* Reset if the reset-gpios is available otherwise the board
 		 * -level design should be guaranteed.
@@ -1017,6 +1046,10 @@ static int btmtkuart_probe(struct serdev_device *serdev)
 		 * mode the device requires for UART transfers.
 		 */
 		msleep(50);
+
+		if (bdev->boot)
+			devm_gpiod_put(&serdev->dev, bdev->boot);
+
 		pinctrl_select_state(bdev->pinctrl, bdev->pins_runtime);
 
 		/* A standalone device doesn't depends on power domain on SoC,
@@ -1037,10 +1070,8 @@ static int btmtkuart_probe(struct serdev_device *serdev)
 	return 0;
 
 err_regulator_disable:
-	if (btmtkuart_is_standalone(bdev))  {
-		pinctrl_select_state(bdev->pinctrl, bdev->pins_boot);
+	if (btmtkuart_is_standalone(bdev))
 		regulator_disable(bdev->vcc);
-	}
 
 	return err;
 }
@@ -1050,9 +1081,9 @@ static void btmtkuart_remove(struct serdev_device *serdev)
 	struct btmtkuart_dev *bdev = serdev_device_get_drvdata(serdev);
 	struct hci_dev *hdev = bdev->hdev;
 
-	if (btmtkuart_is_standalone(bdev))  {
-		pinctrl_select_state(bdev->pinctrl, bdev->pins_boot);
+	if (btmtkuart_is_standalone(bdev)) {
 		regulator_disable(bdev->vcc);
+		clk_disable_unprepare(bdev->osc);
 	}
 
 	hci_unregister_dev(hdev);

drivers/bluetooth/btqca.c

@@ -131,6 +131,7 @@ static void qca_tlv_check_data(struct rome_config *config,
 		 * In case VSE is skipped, only the last segment is acked.
 		 */
 		config->dnld_mode = tlv_patch->download_mode;
+		config->dnld_type = config->dnld_mode;
 
 		BT_DBG("Total Length           : %d bytes",
 		       le32_to_cpu(tlv_patch->total_size));
@@ -251,6 +252,31 @@ static int qca_tlv_send_segment(struct hci_dev *hdev, int seg_size,
 	return err;
 }
 
+static int qca_inject_cmd_complete_event(struct hci_dev *hdev)
+{
+	struct hci_event_hdr *hdr;
+	struct hci_ev_cmd_complete *evt;
+	struct sk_buff *skb;
+
+	skb = bt_skb_alloc(sizeof(*hdr) + sizeof(*evt) + 1, GFP_KERNEL);
+	if (!skb)
+		return -ENOMEM;
+
+	hdr = skb_put(skb, sizeof(*hdr));
+	hdr->evt = HCI_EV_CMD_COMPLETE;
+	hdr->plen = sizeof(*evt) + 1;
+
+	evt = skb_put(skb, sizeof(*evt));
+	evt->ncmd = 1;
+	evt->opcode = QCA_HCI_CC_OPCODE;
+
+	skb_put_u8(skb, QCA_HCI_CC_SUCCESS);
+
+	hci_skb_pkt_type(skb) = HCI_EVENT_PKT;
+
+	return hci_recv_frame(hdev, skb);
+}
+
 static int qca_download_firmware(struct hci_dev *hdev,
 				  struct rome_config *config)
 {
@@ -284,11 +310,22 @@ static int qca_download_firmware(struct hci_dev *hdev,
 		ret = qca_tlv_send_segment(hdev, segsize, segment,
 					    config->dnld_mode);
 		if (ret)
-			break;
+			goto out;
 
 		segment += segsize;
 	}
 
+	/* Latest qualcomm chipsets are not sending a command complete event
+	 * for every fw packet sent. They only respond with a vendor specific
+	 * event for the last packet. This optimization in the chip will
+	 * decrease the BT in initialization time. Here we will inject a command
+	 * complete event to avoid a command timeout error message.
+	 */
+	if (config->dnld_type == ROME_SKIP_EVT_VSE_CC ||
+	    config->dnld_type == ROME_SKIP_EVT_VSE)
+		return qca_inject_cmd_complete_event(hdev);
+
+out:
 	release_firmware(fw);
 
 	return ret;
@@ -319,7 +356,8 @@ int qca_set_bdaddr_rome(struct hci_dev *hdev, const bdaddr_t *bdaddr)
 EXPORT_SYMBOL_GPL(qca_set_bdaddr_rome);
 
 int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
-		   enum qca_btsoc_type soc_type, u32 soc_ver)
+		   enum qca_btsoc_type soc_type, u32 soc_ver,
+		   const char *firmware_name)
 {
 	struct rome_config config;
 	int err;
@@ -352,7 +390,10 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
 
 	/* Download NVM configuration */
 	config.type = TLV_TYPE_NVM;
-	if (qca_is_wcn399x(soc_type))
+	if (firmware_name)
+		snprintf(config.fwname, sizeof(config.fwname),
+			 "qca/%s", firmware_name);
+	else if (qca_is_wcn399x(soc_type))
 		snprintf(config.fwname, sizeof(config.fwname),
 			 "qca/crnv%02x.bin", rom_ver);
 	else

drivers/bluetooth/btqca.h

@@ -28,6 +28,9 @@
 #define QCA_WCN3990_POWERON_PULSE	0xFC
 #define QCA_WCN3990_POWEROFF_PULSE	0xC0
 
+#define QCA_HCI_CC_OPCODE		0xFC00
+#define QCA_HCI_CC_SUCCESS		0x00
+
 enum qca_baudrate {
 	QCA_BAUDRATE_115200 	= 0,
 	QCA_BAUDRATE_57600,
@@ -69,6 +72,7 @@ struct rome_config {
 	char fwname[64];
 	uint8_t user_baud_rate;
 	enum rome_tlv_dnld_mode dnld_mode;
+	enum rome_tlv_dnld_mode dnld_type;
 };
 
 struct edl_event_hdr {
@@ -127,7 +131,8 @@ enum qca_btsoc_type {
 
 int qca_set_bdaddr_rome(struct hci_dev *hdev, const bdaddr_t *bdaddr);
 int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
-		   enum qca_btsoc_type soc_type, u32 soc_ver);
+		   enum qca_btsoc_type soc_type, u32 soc_ver,
+		   const char *firmware_name);
 int qca_read_soc_version(struct hci_dev *hdev, u32 *soc_version);
 int qca_set_bdaddr(struct hci_dev *hdev, const bdaddr_t *bdaddr);
 static inline bool qca_is_wcn399x(enum qca_btsoc_type soc_type)
@@ -142,7 +147,8 @@ static inline int qca_set_bdaddr_rome(struct hci_dev *hdev, const bdaddr_t *bdad
 }
 
 static inline int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
-				 enum qca_btsoc_type soc_type, u32 soc_ver)
+				 enum qca_btsoc_type soc_type, u32 soc_ver,
+				 const char *firmware_name)
 {
 	return -EOPNOTSUPP;
 }

drivers/bluetooth/btrtl.c

@@ -21,6 +21,7 @@
 #define RTL_ROM_LMP_3499	0x3499
 #define RTL_ROM_LMP_8723A	0x1200
 #define RTL_ROM_LMP_8723B	0x8723
+#define RTL_ROM_LMP_8723D	0x8873
 #define RTL_ROM_LMP_8821A	0x8821
 #define RTL_ROM_LMP_8761A	0x8761
 #define RTL_ROM_LMP_8822B	0x8822
@@ -107,6 +108,13 @@ static const struct id_table ic_id_table[] = {
 	  .fw_name  = "rtl_bt/rtl8723ds_fw.bin",
 	  .cfg_name = "rtl_bt/rtl8723ds_config" },
 
+	/* 8723DU */
+	{ IC_INFO(RTL_ROM_LMP_8723D, 0x826C),
+	  .config_needed = true,
+	  .has_rom_version = true,
+	  .fw_name  = "rtl_bt/rtl8723d_fw.bin",
+	  .cfg_name = "rtl_bt/rtl8723d_config" },
+
 	/* 8821A */
 	{ IC_INFO(RTL_ROM_LMP_8821A, 0xa),
 	  .config_needed = false,
@@ -637,6 +645,26 @@ int btrtl_setup_realtek(struct hci_dev *hdev)
 }
 EXPORT_SYMBOL_GPL(btrtl_setup_realtek);
 
+int btrtl_shutdown_realtek(struct hci_dev *hdev)
+{
+	struct sk_buff *skb;
+	int ret;
+
+	/* According to the vendor driver, BT must be reset on close to avoid
+	 * firmware crash.
+	 */
+	skb = __hci_cmd_sync(hdev, HCI_OP_RESET, 0, NULL, HCI_INIT_TIMEOUT);
+	if (IS_ERR(skb)) {
+		ret = PTR_ERR(skb);
+		bt_dev_err(hdev, "HCI reset during shutdown failed");
+		return ret;
+	}
+	kfree_skb(skb);
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(btrtl_shutdown_realtek);
+
 static unsigned int btrtl_convert_baudrate(u32 device_baudrate)
 {
 	switch (device_baudrate) {

drivers/bluetooth/btrtl.h

@@ -55,6 +55,7 @@ void btrtl_free(struct btrtl_device_info *btrtl_dev);
 int btrtl_download_firmware(struct hci_dev *hdev,
 			    struct btrtl_device_info *btrtl_dev);
 int btrtl_setup_realtek(struct hci_dev *hdev);
+int btrtl_shutdown_realtek(struct hci_dev *hdev);
 int btrtl_get_uart_settings(struct hci_dev *hdev,
 			    struct btrtl_device_info *btrtl_dev,
 			    unsigned int *controller_baudrate,
@@ -83,6 +84,11 @@ static inline int btrtl_setup_realtek(struct hci_dev *hdev)
 	return -EOPNOTSUPP;
 }
 
+static inline int btrtl_shutdown_realtek(struct hci_dev *hdev)
+{
+	return -EOPNOTSUPP;
+}
+
 static inline int btrtl_get_uart_settings(struct hci_dev *hdev,
 					  struct btrtl_device_info *btrtl_dev,
 					  unsigned int *controller_baudrate,

drivers/bluetooth/btsdio.c

@@ -286,6 +286,7 @@ static int btsdio_probe(struct sdio_func *func,
 		switch (func->device) {
 		case SDIO_DEVICE_ID_BROADCOM_43341:
 		case SDIO_DEVICE_ID_BROADCOM_43430:
+		case SDIO_DEVICE_ID_BROADCOM_4356:
 			return -ENODEV;
 		}
 	}

drivers/bluetooth/btusb.c

@@ -11,6 +11,7 @@
 #include <linux/usb.h>
 #include <linux/usb/quirks.h>
 #include <linux/firmware.h>
+#include <linux/iopoll.h>
 #include <linux/of_device.h>
 #include <linux/of_irq.h>
 #include <linux/suspend.h>
@@ -55,6 +56,7 @@ static struct usb_driver btusb_driver;
 #define BTUSB_BCM2045		0x40000
 #define BTUSB_IFNUM_2		0x80000
 #define BTUSB_CW6622		0x100000
+#define BTUSB_MEDIATEK		0x200000
 
 static const struct usb_device_id btusb_table[] = {
 	/* Generic Bluetooth USB device */
@@ -264,7 +266,9 @@ static const struct usb_device_id blacklist_table[] = {
 	{ USB_DEVICE(0x04ca, 0x3015), .driver_info = BTUSB_QCA_ROME },
 	{ USB_DEVICE(0x04ca, 0x3016), .driver_info = BTUSB_QCA_ROME },
 	{ USB_DEVICE(0x04ca, 0x301a), .driver_info = BTUSB_QCA_ROME },
+	{ USB_DEVICE(0x13d3, 0x3491), .driver_info = BTUSB_QCA_ROME },
 	{ USB_DEVICE(0x13d3, 0x3496), .driver_info = BTUSB_QCA_ROME },
+	{ USB_DEVICE(0x13d3, 0x3501), .driver_info = BTUSB_QCA_ROME },
 
 	/* Broadcom BCM2035 */
 	{ USB_DEVICE(0x0a5c, 0x2009), .driver_info = BTUSB_BCM92035 },
@@ -346,6 +350,10 @@ static const struct usb_device_id blacklist_table[] = {
 	{ USB_VENDOR_AND_INTERFACE_INFO(0x0bda, 0xe0, 0x01, 0x01),
 	  .driver_info = BTUSB_REALTEK },
 
+	/* MediaTek Bluetooth devices */
+	{ USB_VENDOR_AND_INTERFACE_INFO(0x0e8d, 0xe0, 0x01, 0x01),
+	  .driver_info = BTUSB_MEDIATEK },
+
 	/* Additional Realtek 8723AE Bluetooth devices */
 	{ USB_DEVICE(0x0930, 0x021d), .driver_info = BTUSB_REALTEK },
 	{ USB_DEVICE(0x13d3, 0x3394), .driver_info = BTUSB_REALTEK },
@@ -426,6 +434,7 @@ static const struct dmi_system_id btusb_needs_reset_resume_table[] = {
 #define BTUSB_DIAG_RUNNING	10
 #define BTUSB_OOB_WAKE_ENABLED	11
 #define BTUSB_HW_RESET_ACTIVE	12
+#define BTUSB_TX_WAIT_VND_EVT	13
 
 struct btusb_data {
 	struct hci_dev       *hdev;
@@ -449,6 +458,7 @@ struct btusb_data {
 	struct usb_anchor bulk_anchor;
 	struct usb_anchor isoc_anchor;
 	struct usb_anchor diag_anchor;
+	struct usb_anchor ctrl_anchor;
 	spinlock_t rxlock;
 
 	struct sk_buff *evt_skb;
@@ -1202,6 +1212,7 @@ static void btusb_stop_traffic(struct btusb_data *data)
 	usb_kill_anchored_urbs(&data->bulk_anchor);
 	usb_kill_anchored_urbs(&data->isoc_anchor);
 	usb_kill_anchored_urbs(&data->diag_anchor);
+	usb_kill_anchored_urbs(&data->ctrl_anchor);
 }
 
 static int btusb_close(struct hci_dev *hdev)
@@ -2437,6 +2448,568 @@ static int btusb_shutdown_intel_new(struct hci_dev *hdev)
 	return 0;
 }
 
+#ifdef CONFIG_BT_HCIBTUSB_MTK
+
+#define FIRMWARE_MT7663		"mediatek/mt7663pr2h.bin"
+#define FIRMWARE_MT7668		"mediatek/mt7668pr2h.bin"
+
+#define HCI_WMT_MAX_EVENT_SIZE		64
+
+enum {
+	BTMTK_WMT_PATCH_DWNLD = 0x1,
+	BTMTK_WMT_FUNC_CTRL = 0x6,
+	BTMTK_WMT_RST = 0x7,
+	BTMTK_WMT_SEMAPHORE = 0x17,
+};
+
+enum {
+	BTMTK_WMT_INVALID,
+	BTMTK_WMT_PATCH_UNDONE,
+	BTMTK_WMT_PATCH_DONE,
+	BTMTK_WMT_ON_UNDONE,
+	BTMTK_WMT_ON_DONE,
+	BTMTK_WMT_ON_PROGRESS,
+};
+
+struct btmtk_wmt_hdr {
+	u8	dir;
+	u8	op;
+	__le16	dlen;
+	u8	flag;
+} __packed;
+
+struct btmtk_hci_wmt_cmd {
+	struct btmtk_wmt_hdr hdr;
+	u8 data[256];
+} __packed;
+
+struct btmtk_hci_wmt_evt {
+	struct hci_event_hdr hhdr;
+	struct btmtk_wmt_hdr whdr;
+} __packed;
+
+struct btmtk_hci_wmt_evt_funcc {
+	struct btmtk_hci_wmt_evt hwhdr;
+	__be16 status;
+} __packed;
+
+struct btmtk_tci_sleep {
+	u8 mode;
+	__le16 duration;
+	__le16 host_duration;
+	u8 host_wakeup_pin;
+	u8 time_compensation;
+} __packed;
+
+struct btmtk_hci_wmt_params {
+	u8 op;
+	u8 flag;
+	u16 dlen;
+	const void *data;
+	u32 *status;
+};
+
+static void btusb_mtk_wmt_recv(struct urb *urb)
+{
+	struct hci_dev *hdev = urb->context;
+	struct btusb_data *data = hci_get_drvdata(hdev);
+	struct hci_event_hdr *hdr;
+	struct sk_buff *skb;
+	int err;
+
+	if (urb->status == 0 && urb->actual_length > 0) {
+		hdev->stat.byte_rx += urb->actual_length;
+
+		/* WMT event shouldn't be fragmented and the size should be
+		 * less than HCI_WMT_MAX_EVENT_SIZE.
+		 */
+		skb = bt_skb_alloc(HCI_WMT_MAX_EVENT_SIZE, GFP_ATOMIC);
+		if (!skb) {
+			hdev->stat.err_rx++;
+			goto err_out;
+		}
+
+		hci_skb_pkt_type(skb) = HCI_EVENT_PKT;
+		skb_put_data(skb, urb->transfer_buffer, urb->actual_length);
+
+		hdr = (void *)skb->data;
+		/* Fix up the vendor event id with 0xff for vendor specific
+		 * instead of 0xe4 so that event send via monitoring socket can
+		 * be parsed properly.
+		 */
+		hdr->evt = 0xff;
+
+		/* When someone waits for the WMT event, the skb is being cloned
+		 * and being processed the events from there then.
+		 */
+		if (test_bit(BTUSB_TX_WAIT_VND_EVT, &data->flags)) {
+			data->evt_skb = skb_clone(skb, GFP_KERNEL);
+			if (!data->evt_skb)
+				goto err_out;
+		}
+
+		err = hci_recv_frame(hdev, skb);
+		if (err < 0)
+			goto err_free_skb;
+
+		if (test_and_clear_bit(BTUSB_TX_WAIT_VND_EVT,
+				       &data->flags)) {
+			/* Barrier to sync with other CPUs */
+			smp_mb__after_atomic();
+			wake_up_bit(&data->flags,
+				    BTUSB_TX_WAIT_VND_EVT);
+		}
+err_out:
+		return;
+err_free_skb:
+		kfree_skb(data->evt_skb);
+		data->evt_skb = NULL;
+		return;
+	} else if (urb->status == -ENOENT) {
+		/* Avoid suspend failed when usb_kill_urb */
+		return;
+	}
+
+	usb_mark_last_busy(data->udev);
+
+	/* The URB complete handler is still called with urb->actual_length = 0
+	 * when the event is not available, so we should keep re-submitting
+	 * URB until WMT event returns, Also, It's necessary to wait some time
+	 * between the two consecutive control URBs to relax the target device
+	 * to generate the event. Otherwise, the WMT event cannot return from
+	 * the device successfully.
+	 */
+	udelay(100);
+
+	usb_anchor_urb(urb, &data->ctrl_anchor);
+	err = usb_submit_urb(urb, GFP_ATOMIC);
+	if (err < 0) {
+		/* -EPERM: urb is being killed;
+		 * -ENODEV: device got disconnected
+		 */
+		if (err != -EPERM && err != -ENODEV)
+			bt_dev_err(hdev, "urb %p failed to resubmit (%d)",
+				   urb, -err);
+		usb_unanchor_urb(urb);
+	}
+}
+
+static int btusb_mtk_submit_wmt_recv_urb(struct hci_dev *hdev)
+{
+	struct btusb_data *data = hci_get_drvdata(hdev);
+	struct usb_ctrlrequest *dr;
+	unsigned char *buf;
+	int err, size = 64;
+	unsigned int pipe;
+	struct urb *urb;
+
+	urb = usb_alloc_urb(0, GFP_KERNEL);
+	if (!urb)
+		return -ENOMEM;
+
+	dr = kmalloc(sizeof(*dr), GFP_KERNEL);
+	if (!dr) {
+		usb_free_urb(urb);
+		return -ENOMEM;
+	}
+
+	dr->bRequestType = USB_TYPE_VENDOR | USB_DIR_IN;
+	dr->bRequest     = 1;
+	dr->wIndex       = cpu_to_le16(0);
+	dr->wValue       = cpu_to_le16(48);
+	dr->wLength      = cpu_to_le16(size);
+
+	buf = kmalloc(size, GFP_KERNEL);
+	if (!buf) {
+		kfree(dr);
+		return -ENOMEM;
+	}
+
+	pipe = usb_rcvctrlpipe(data->udev, 0);
+
+	usb_fill_control_urb(urb, data->udev, pipe, (void *)dr,
+			     buf, size, btusb_mtk_wmt_recv, hdev);
+
+	urb->transfer_flags |= URB_FREE_BUFFER;
+
+	usb_anchor_urb(urb, &data->ctrl_anchor);
+	err = usb_submit_urb(urb, GFP_KERNEL);
+	if (err < 0) {
+		if (err != -EPERM && err != -ENODEV)
+			bt_dev_err(hdev, "urb %p submission failed (%d)",
+				   urb, -err);
+		usb_unanchor_urb(urb);
+	}
+
+	usb_free_urb(urb);
+
+	return err;
+}
+
+static int btusb_mtk_hci_wmt_sync(struct hci_dev *hdev,
+				  struct btmtk_hci_wmt_params *wmt_params)
+{
+	struct btusb_data *data = hci_get_drvdata(hdev);
+	struct btmtk_hci_wmt_evt_funcc *wmt_evt_funcc;
+	u32 hlen, status = BTMTK_WMT_INVALID;
+	struct btmtk_hci_wmt_evt *wmt_evt;
+	struct btmtk_hci_wmt_cmd wc;
+	struct btmtk_wmt_hdr *hdr;
+	int err;
+
+	/* Submit control IN URB on demand to process the WMT event */
+	err = btusb_mtk_submit_wmt_recv_urb(hdev);
+	if (err < 0)
+		return err;
+
+	/* Send the WMT command and wait until the WMT event returns */
+	hlen = sizeof(*hdr) + wmt_params->dlen;
+	if (hlen > 255)
+		return -EINVAL;
+
+	hdr = (struct btmtk_wmt_hdr *)&wc;
+	hdr->dir = 1;
+	hdr->op = wmt_params->op;
+	hdr->dlen = cpu_to_le16(wmt_params->dlen + 1);
+	hdr->flag = wmt_params->flag;
+	memcpy(wc.data, wmt_params->data, wmt_params->dlen);
+
+	set_bit(BTUSB_TX_WAIT_VND_EVT, &data->flags);
+
+	err = __hci_cmd_send(hdev, 0xfc6f, hlen, &wc);
+
+	if (err < 0) {
+		clear_bit(BTUSB_TX_WAIT_VND_EVT, &data->flags);
+		return err;
+	}
+
+	/* The vendor specific WMT commands are all answered by a vendor
+	 * specific event and will have the Command Status or Command
+	 * Complete as with usual HCI command flow control.
+	 *
+	 * After sending the command, wait for BTUSB_TX_WAIT_VND_EVT
+	 * state to be cleared. The driver specific event receive routine
+	 * will clear that state and with that indicate completion of the
+	 * WMT command.
+	 */
+	err = wait_on_bit_timeout(&data->flags, BTUSB_TX_WAIT_VND_EVT,
+				  TASK_INTERRUPTIBLE, HCI_INIT_TIMEOUT);
+	if (err == -EINTR) {
+		bt_dev_err(hdev, "Execution of wmt command interrupted");
+		clear_bit(BTUSB_TX_WAIT_VND_EVT, &data->flags);
+		return err;
+	}
+
+	if (err) {
+		bt_dev_err(hdev, "Execution of wmt command timed out");
+		clear_bit(BTUSB_TX_WAIT_VND_EVT, &data->flags);
+		return -ETIMEDOUT;
+	}
+
+	/* Parse and handle the return WMT event */
+	wmt_evt = (struct btmtk_hci_wmt_evt *)data->evt_skb->data;
+	if (wmt_evt->whdr.op != hdr->op) {
+		bt_dev_err(hdev, "Wrong op received %d expected %d",
+			   wmt_evt->whdr.op, hdr->op);
+		err = -EIO;
+		goto err_free_skb;
+	}
+
+	switch (wmt_evt->whdr.op) {
+	case BTMTK_WMT_SEMAPHORE:
+		if (wmt_evt->whdr.flag == 2)
+			status = BTMTK_WMT_PATCH_UNDONE;
+		else
+			status = BTMTK_WMT_PATCH_DONE;
+		break;
+	case BTMTK_WMT_FUNC_CTRL:
+		wmt_evt_funcc = (struct btmtk_hci_wmt_evt_funcc *)wmt_evt;
+		if (be16_to_cpu(wmt_evt_funcc->status) == 0x404)
+			status = BTMTK_WMT_ON_DONE;
+		else if (be16_to_cpu(wmt_evt_funcc->status) == 0x420)
+			status = BTMTK_WMT_ON_PROGRESS;
+		else
+			status = BTMTK_WMT_ON_UNDONE;
+		break;
+	}
+
+	if (wmt_params->status)
+		*wmt_params->status = status;
+
+err_free_skb:
+	kfree_skb(data->evt_skb);
+	data->evt_skb = NULL;
+
+	return err;
+}
+
+static int btusb_mtk_setup_firmware(struct hci_dev *hdev, const char *fwname)
+{
+	struct btmtk_hci_wmt_params wmt_params;
+	const struct firmware *fw;
+	const u8 *fw_ptr;
+	size_t fw_size;
+	int err, dlen;
+	u8 flag;
+
+	err = request_firmware(&fw, fwname, &hdev->dev);
+	if (err < 0) {
+		bt_dev_err(hdev, "Failed to load firmware file (%d)", err);
+		return err;
+	}
+
+	fw_ptr = fw->data;
+	fw_size = fw->size;
+
+	/* The size of patch header is 30 bytes, should be skip */
+	if (fw_size < 30)
+		goto err_release_fw;
+
+	fw_size -= 30;
+	fw_ptr += 30;
+	flag = 1;
+
+	wmt_params.op = BTMTK_WMT_PATCH_DWNLD;
+	wmt_params.status = NULL;
+
+	while (fw_size > 0) {
+		dlen = min_t(int, 250, fw_size);
+
+		/* Tell deivice the position in sequence */
+		if (fw_size - dlen <= 0)
+			flag = 3;
+		else if (fw_size < fw->size - 30)
+			flag = 2;
+
+		wmt_params.flag = flag;
+		wmt_params.dlen = dlen;
+		wmt_params.data = fw_ptr;
+
+		err = btusb_mtk_hci_wmt_sync(hdev, &wmt_params);
+		if (err < 0) {
+			bt_dev_err(hdev, "Failed to send wmt patch dwnld (%d)",
+				   err);
+			goto err_release_fw;
+		}
+
+		fw_size -= dlen;
+		fw_ptr += dlen;
+	}
+
+	wmt_params.op = BTMTK_WMT_RST;
+	wmt_params.flag = 4;
+	wmt_params.dlen = 0;
+	wmt_params.data = NULL;
+	wmt_params.status = NULL;
+
+	/* Activate funciton the firmware providing to */
+	err = btusb_mtk_hci_wmt_sync(hdev, &wmt_params);
+	if (err < 0) {
+		bt_dev_err(hdev, "Failed to send wmt rst (%d)", err);
+		return err;
+	}
+
+	/* Wait a few moments for firmware activation done */
+	usleep_range(10000, 12000);
+
+err_release_fw:
+	release_firmware(fw);
+
+	return err;
+}
+
+static int btusb_mtk_func_query(struct hci_dev *hdev)
+{
+	struct btmtk_hci_wmt_params wmt_params;
+	int status, err;
+	u8 param = 0;
+
+	/* Query whether the function is enabled */
+	wmt_params.op = BTMTK_WMT_FUNC_CTRL;
+	wmt_params.flag = 4;
+	wmt_params.dlen = sizeof(param);
+	wmt_params.data = &param;
+	wmt_params.status = &status;
+
+	err = btusb_mtk_hci_wmt_sync(hdev, &wmt_params);
+	if (err < 0) {
+		bt_dev_err(hdev, "Failed to query function status (%d)", err);
+		return err;
+	}
+
+	return status;
+}
+
+static int btusb_mtk_reg_read(struct btusb_data *data, u32 reg, u32 *val)
+{
+	int pipe, err, size = sizeof(u32);
+	void *buf;
+
+	buf = kzalloc(size, GFP_KERNEL);
+	if (!buf)
+		return -ENOMEM;
+
+	pipe = usb_rcvctrlpipe(data->udev, 0);
+	err = usb_control_msg(data->udev, pipe, 0x63,
+			      USB_TYPE_VENDOR | USB_DIR_IN,
+			      reg >> 16, reg & 0xffff,
+			      buf, size, USB_CTRL_SET_TIMEOUT);
+	if (err < 0)
+		goto err_free_buf;
+
+	*val = get_unaligned_le32(buf);
+
+err_free_buf:
+	kfree(buf);
+
+	return err;
+}
+
+static int btusb_mtk_id_get(struct btusb_data *data, u32 *id)
+{
+	return btusb_mtk_reg_read(data, 0x80000008, id);
+}
+
+static int btusb_mtk_setup(struct hci_dev *hdev)
+{
+	struct btusb_data *data = hci_get_drvdata(hdev);
+	struct btmtk_hci_wmt_params wmt_params;
+	ktime_t calltime, delta, rettime;
+	struct btmtk_tci_sleep tci_sleep;
+	unsigned long long duration;
+	struct sk_buff *skb;
+	const char *fwname;
+	int err, status;
+	u32 dev_id;
+	u8 param;
+
+	calltime = ktime_get();
+
+	err = btusb_mtk_id_get(data, &dev_id);
+	if (err < 0) {
+		bt_dev_err(hdev, "Failed to get device id (%d)", err);
+		return err;
+	}
+
+	switch (dev_id) {
+	case 0x7663:
+		fwname = FIRMWARE_MT7663;
+		break;
+	case 0x7668:
+		fwname = FIRMWARE_MT7668;
+		break;
+	default:
+		bt_dev_err(hdev, "Unsupported support hardware variant (%08x)",
+			   dev_id);
+		return -ENODEV;
+	}
+
+	/* Query whether the firmware is already download */
+	wmt_params.op = BTMTK_WMT_SEMAPHORE;
+	wmt_params.flag = 1;
+	wmt_params.dlen = 0;
+	wmt_params.data = NULL;
+	wmt_params.status = &status;
+
+	err = btusb_mtk_hci_wmt_sync(hdev, &wmt_params);
+	if (err < 0) {
+		bt_dev_err(hdev, "Failed to query firmware status (%d)", err);
+		return err;
+	}
+
+	if (status == BTMTK_WMT_PATCH_DONE) {
+		bt_dev_info(hdev, "firmware already downloaded");
+		goto ignore_setup_fw;
+	}
+
+	/* Setup a firmware which the device definitely requires */
+	err = btusb_mtk_setup_firmware(hdev, fwname);
+	if (err < 0)
+		return err;
+
+ignore_setup_fw:
+	err = readx_poll_timeout(btusb_mtk_func_query, hdev, status,
+				 status < 0 || status != BTMTK_WMT_ON_PROGRESS,
+				 2000, 5000000);
+	/* -ETIMEDOUT happens */
+	if (err < 0)
+		return err;
+
+	/* The other errors happen in btusb_mtk_func_query */
+	if (status < 0)
+		return status;
+
+	if (status == BTMTK_WMT_ON_DONE) {
+		bt_dev_info(hdev, "function already on");
+		goto ignore_func_on;
+	}
+
+	/* Enable Bluetooth protocol */
+	param = 1;
+	wmt_params.op = BTMTK_WMT_FUNC_CTRL;
+	wmt_params.flag = 0;
+	wmt_params.dlen = sizeof(param);
+	wmt_params.data = &param;
+	wmt_params.status = NULL;
+
+	err = btusb_mtk_hci_wmt_sync(hdev, &wmt_params);
+	if (err < 0) {
+		bt_dev_err(hdev, "Failed to send wmt func ctrl (%d)", err);
+		return err;
+	}
+
+ignore_func_on:
+	/* Apply the low power environment setup */
+	tci_sleep.mode = 0x5;
+	tci_sleep.duration = cpu_to_le16(0x640);
+	tci_sleep.host_duration = cpu_to_le16(0x640);
+	tci_sleep.host_wakeup_pin = 0;
+	tci_sleep.time_compensation = 0;
+
+	skb = __hci_cmd_sync(hdev, 0xfc7a, sizeof(tci_sleep), &tci_sleep,
+			     HCI_INIT_TIMEOUT);
+	if (IS_ERR(skb)) {
+		err = PTR_ERR(skb);
+		bt_dev_err(hdev, "Failed to apply low power setting (%d)", err);
+		return err;
+	}
+	kfree_skb(skb);
+
+	rettime = ktime_get();
+	delta = ktime_sub(rettime, calltime);
+	duration = (unsigned long long)ktime_to_ns(delta) >> 10;
+
+	bt_dev_info(hdev, "Device setup in %llu usecs", duration);
+
+	return 0;
+}
+
+static int btusb_mtk_shutdown(struct hci_dev *hdev)
+{
+	struct btmtk_hci_wmt_params wmt_params;
+	u8 param = 0;
+	int err;
+
+	/* Disable the device */
+	wmt_params.op = BTMTK_WMT_FUNC_CTRL;
+	wmt_params.flag = 0;
+	wmt_params.dlen = sizeof(param);
+	wmt_params.data = &param;
+	wmt_params.status = NULL;
+
+	err = btusb_mtk_hci_wmt_sync(hdev, &wmt_params);
+	if (err < 0) {
+		bt_dev_err(hdev, "Failed to send wmt func ctrl (%d)", err);
+		return err;
+	}
+
+	return 0;
+}
+
+MODULE_FIRMWARE(FIRMWARE_MT7663);
+MODULE_FIRMWARE(FIRMWARE_MT7668);
+#endif
+
 #ifdef CONFIG_PM
 /* Configure an out-of-band gpio as wake-up pin, if specified in device tree */
 static int marvell_config_oob_wake(struct hci_dev *hdev)
@@ -3044,6 +3617,7 @@ static int btusb_probe(struct usb_interface *intf,
 	init_usb_anchor(&data->bulk_anchor);
 	init_usb_anchor(&data->isoc_anchor);
 	init_usb_anchor(&data->diag_anchor);
+	init_usb_anchor(&data->ctrl_anchor);
 	spin_lock_init(&data->rxlock);
 
 	if (id->driver_info & BTUSB_INTEL_NEW) {
@@ -3157,6 +3731,15 @@ static int btusb_probe(struct usb_interface *intf,
 	if (id->driver_info & BTUSB_MARVELL)
 		hdev->set_bdaddr = btusb_set_bdaddr_marvell;
 
+#ifdef CONFIG_BT_HCIBTUSB_MTK
+	if (id->driver_info & BTUSB_MEDIATEK) {
+		hdev->setup = btusb_mtk_setup;
+		hdev->shutdown = btusb_mtk_shutdown;
+		hdev->manufacturer = 70;
+		set_bit(HCI_QUIRK_NON_PERSISTENT_SETUP, &hdev->quirks);
+	}
+#endif
+
 	if (id->driver_info & BTUSB_SWAVE) {
 		set_bit(HCI_QUIRK_FIXUP_INQUIRY_MODE, &hdev->quirks);
 		set_bit(HCI_QUIRK_BROKEN_LOCAL_COMMANDS, &hdev->quirks);
@@ -3184,6 +3767,7 @@ static int btusb_probe(struct usb_interface *intf,
 #ifdef CONFIG_BT_HCIBTUSB_RTL
 	if (id->driver_info & BTUSB_REALTEK) {
 		hdev->setup = btrtl_setup_realtek;
+		hdev->shutdown = btrtl_shutdown_realtek;
 
 		/* Realtek devices lose their updated firmware over suspend,
 		 * but the USB hub doesn't notice any status change.

drivers/bluetooth/hci_bcsp.c

@@ -744,6 +744,11 @@ static int bcsp_close(struct hci_uart *hu)
 	skb_queue_purge(&bcsp->rel);
 	skb_queue_purge(&bcsp->unrel);
 
+	if (bcsp->rx_skb) {
+		kfree_skb(bcsp->rx_skb);
+		bcsp->rx_skb = NULL;
+	}
+
 	kfree(bcsp);
 	return 0;
 }

drivers/bluetooth/hci_ldisc.c

@@ -178,6 +178,7 @@ static void hci_uart_write_work(struct work_struct *work)
 		goto restart;
 
 	clear_bit(HCI_UART_SENDING, &hu->tx_state);
+	wake_up_bit(&hu->tx_state, HCI_UART_SENDING);
 }
 
 void hci_uart_init_work(struct work_struct *work)
@@ -213,6 +214,13 @@ int hci_uart_init_ready(struct hci_uart *hu)
 	return 0;
 }
 
+int hci_uart_wait_until_sent(struct hci_uart *hu)
+{
+	return wait_on_bit_timeout(&hu->tx_state, HCI_UART_SENDING,
+				   TASK_INTERRUPTIBLE,
+				   msecs_to_jiffies(2000));
+}
+
 /* ------- Interface to HCI layer ------ */
 /* Reset device */
 static int hci_uart_flush(struct hci_dev *hdev)

drivers/bluetooth/hci_ll.c

@@ -128,6 +128,7 @@ static int ll_open(struct hci_uart *hu)
 
 	if (hu->serdev) {
 		struct ll_device *lldev = serdev_device_get_drvdata(hu->serdev);
+
 		if (!IS_ERR(lldev->ext_clk))
 			clk_prepare_enable(lldev->ext_clk);
 	}
@@ -162,6 +163,7 @@ static int ll_close(struct hci_uart *hu)
 
 	if (hu->serdev) {
 		struct ll_device *lldev = serdev_device_get_drvdata(hu->serdev);
+
 		gpiod_set_value_cansleep(lldev->enable_gpio, 0);
 
 		clk_disable_unprepare(lldev->ext_clk);
@@ -227,7 +229,8 @@ static void ll_device_want_to_wakeup(struct hci_uart *hu)
 		break;
 	default:
 		/* any other state is illegal */
-		BT_ERR("received HCILL_WAKE_UP_IND in state %ld", ll->hcill_state);
+		BT_ERR("received HCILL_WAKE_UP_IND in state %ld",
+		       ll->hcill_state);
 		break;
 	}
 
@@ -256,7 +259,8 @@ static void ll_device_want_to_sleep(struct hci_uart *hu)
 
 	/* sanity check */
 	if (ll->hcill_state != HCILL_AWAKE)
-		BT_ERR("ERR: HCILL_GO_TO_SLEEP_IND in state %ld", ll->hcill_state);
+		BT_ERR("ERR: HCILL_GO_TO_SLEEP_IND in state %ld",
+		       ll->hcill_state);
 
 	/* acknowledge device sleep */
 	if (send_hcill_cmd(HCILL_GO_TO_SLEEP_ACK, hu) < 0) {
@@ -289,7 +293,8 @@ static void ll_device_woke_up(struct hci_uart *hu)
 
 	/* sanity check */
 	if (ll->hcill_state != HCILL_ASLEEP_TO_AWAKE)
-		BT_ERR("received HCILL_WAKE_UP_ACK in state %ld", ll->hcill_state);
+		BT_ERR("received HCILL_WAKE_UP_ACK in state %ld",
+		       ll->hcill_state);
 
 	/* send pending packets and change state to HCILL_AWAKE */
 	__ll_do_awake(ll);
@@ -338,7 +343,8 @@ static int ll_enqueue(struct hci_uart *hu, struct sk_buff *skb)
 		skb_queue_tail(&ll->tx_wait_q, skb);
 		break;
 	default:
-		BT_ERR("illegal hcill state: %ld (losing packet)", ll->hcill_state);
+		BT_ERR("illegal hcill state: %ld (losing packet)",
+		       ll->hcill_state);
 		kfree_skb(skb);
 		break;
 	}
@@ -438,6 +444,7 @@ static int ll_recv(struct hci_uart *hu, const void *data, int count)
 static struct sk_buff *ll_dequeue(struct hci_uart *hu)
 {
 	struct ll_struct *ll = hu->priv;
+
 	return skb_dequeue(&ll->txq);
 }
 
@@ -449,7 +456,8 @@ static int read_local_version(struct hci_dev *hdev)
 	struct sk_buff *skb;
 	struct hci_rp_read_local_version *ver;
 
-	skb = __hci_cmd_sync(hdev, HCI_OP_READ_LOCAL_VERSION, 0, NULL, HCI_INIT_TIMEOUT);
+	skb = __hci_cmd_sync(hdev, HCI_OP_READ_LOCAL_VERSION, 0, NULL,
+			     HCI_INIT_TIMEOUT);
 	if (IS_ERR(skb)) {
 		bt_dev_err(hdev, "Reading TI version information failed (%ld)",
 			   PTR_ERR(skb));
@@ -469,11 +477,38 @@ static int read_local_version(struct hci_dev *hdev)
 	version = le16_to_cpu(ver->lmp_subver);
 
 out:
-	if (err) bt_dev_err(hdev, "Failed to read TI version info: %d", err);
+	if (err)
+		bt_dev_err(hdev, "Failed to read TI version info: %d", err);
 	kfree_skb(skb);
 	return err ? err : version;
 }
 
+static int send_command_from_firmware(struct ll_device *lldev,
+				      struct hci_command *cmd)
+{
+	struct sk_buff *skb;
+
+	if (cmd->opcode == HCI_VS_UPDATE_UART_HCI_BAUDRATE) {
+		/* ignore remote change
+		 * baud rate HCI VS command
+		 */
+		bt_dev_warn(lldev->hu.hdev,
+			    "change remote baud rate command in firmware");
+		return 0;
+	}
+	if (cmd->prefix != 1)
+		bt_dev_dbg(lldev->hu.hdev, "command type %d", cmd->prefix);
+
+	skb = __hci_cmd_sync(lldev->hu.hdev, cmd->opcode, cmd->plen,
+			     &cmd->speed, HCI_INIT_TIMEOUT);
+	if (IS_ERR(skb)) {
+		bt_dev_err(lldev->hu.hdev, "send command failed");
+		return PTR_ERR(skb);
+	}
+	kfree_skb(skb);
+	return 0;
+}
+
 /**
  * download_firmware -
  *	internal function which parses through the .bts firmware
@@ -486,7 +521,6 @@ static int download_firmware(struct ll_device *lldev)
 	unsigned char *ptr, *action_ptr;
 	unsigned char bts_scr_name[40];	/* 40 char long bts scr name? */
 	const struct firmware *fw;
-	struct sk_buff *skb;
 	struct hci_command *cmd;
 
 	version = read_local_version(lldev->hu.hdev);
@@ -528,23 +562,9 @@ static int download_firmware(struct ll_device *lldev)
 		case ACTION_SEND_COMMAND:	/* action send */
 			bt_dev_dbg(lldev->hu.hdev, "S");
 			cmd = (struct hci_command *)action_ptr;
-			if (cmd->opcode == HCI_VS_UPDATE_UART_HCI_BAUDRATE) {
-				/* ignore remote change
-				 * baud rate HCI VS command
-				 */
-				bt_dev_warn(lldev->hu.hdev, "change remote baud rate command in firmware");
-				break;
-			}
-			if (cmd->prefix != 1)
-				bt_dev_dbg(lldev->hu.hdev, "command type %d", cmd->prefix);
-
-			skb = __hci_cmd_sync(lldev->hu.hdev, cmd->opcode, cmd->plen, &cmd->speed, HCI_INIT_TIMEOUT);
-			if (IS_ERR(skb)) {
-				bt_dev_err(lldev->hu.hdev, "send command failed");
-				err = PTR_ERR(skb);
+			err = send_command_from_firmware(lldev, cmd);
+			if (err)
 				goto out_rel_fw;
-			}
-			kfree_skb(skb);
 			break;
 		case ACTION_WAIT_EVENT:  /* wait */
 			/* no need to wait as command was synchronous */
@@ -601,6 +621,13 @@ static int ll_setup(struct hci_uart *hu)
 
 	serdev_device_set_flow_control(serdev, true);
 
+	if (hu->oper_speed)
+		speed = hu->oper_speed;
+	else if (hu->proto->oper_speed)
+		speed = hu->proto->oper_speed;
+	else
+		speed = 0;
+
 	do {
 		/* Reset the Bluetooth device */
 		gpiod_set_value_cansleep(lldev->enable_gpio, 0);
@@ -612,6 +639,20 @@ static int ll_setup(struct hci_uart *hu)
 			return err;
 		}
 
+		if (speed) {
+			__le32 speed_le = cpu_to_le32(speed);
+			struct sk_buff *skb;
+
+			skb = __hci_cmd_sync(hu->hdev,
+					     HCI_VS_UPDATE_UART_HCI_BAUDRATE,
+					     sizeof(speed_le), &speed_le,
+					     HCI_INIT_TIMEOUT);
+			if (!IS_ERR(skb)) {
+				kfree_skb(skb);
+				serdev_device_set_baudrate(serdev, speed);
+			}
+		}
+
 		err = download_firmware(lldev);
 		if (!err)
 			break;
@@ -636,25 +677,7 @@ static int ll_setup(struct hci_uart *hu)
 	}
 
 	/* Operational speed if any */
-	if (hu->oper_speed)
-		speed = hu->oper_speed;
-	else if (hu->proto->oper_speed)
-		speed = hu->proto->oper_speed;
-	else
-		speed = 0;
-
-	if (speed) {
-		__le32 speed_le = cpu_to_le32(speed);
-		struct sk_buff *skb;
 
-		skb = __hci_cmd_sync(hu->hdev, HCI_VS_UPDATE_UART_HCI_BAUDRATE,
-				     sizeof(speed_le), &speed_le,
-				     HCI_INIT_TIMEOUT);
-		if (!IS_ERR(skb)) {
-			kfree_skb(skb);
-			serdev_device_set_baudrate(serdev, speed);
-		}
-	}
 
 	return 0;
 }
@@ -676,7 +699,9 @@ static int hci_ti_probe(struct serdev_device *serdev)
 	serdev_device_set_drvdata(serdev, lldev);
 	lldev->serdev = hu->serdev = serdev;
 
-	lldev->enable_gpio = devm_gpiod_get_optional(&serdev->dev, "enable", GPIOD_OUT_LOW);
+	lldev->enable_gpio = devm_gpiod_get_optional(&serdev->dev,
+						     "enable",
+						     GPIOD_OUT_LOW);
 	if (IS_ERR(lldev->enable_gpio))
 		return PTR_ERR(lldev->enable_gpio);
 

drivers/bluetooth/hci_mrvl.c

@@ -13,6 +13,8 @@
 #include <linux/firmware.h>
 #include <linux/module.h>
 #include <linux/tty.h>
+#include <linux/of.h>
+#include <linux/serdev.h>
 
 #include <net/bluetooth/bluetooth.h>
 #include <net/bluetooth/hci_core.h>
@@ -40,6 +42,10 @@ struct mrvl_data {
 	u8 id, rev;
 };
 
+struct mrvl_serdev {
+	struct hci_uart hu;
+};
+
 struct hci_mrvl_pkt {
 	__le16 lhs;
 	__le16 rhs;
@@ -49,6 +55,7 @@ struct hci_mrvl_pkt {
 static int mrvl_open(struct hci_uart *hu)
 {
 	struct mrvl_data *mrvl;
+	int ret;
 
 	BT_DBG("hu %p", hu);
 
@@ -62,7 +69,18 @@ static int mrvl_open(struct hci_uart *hu)
 	set_bit(STATE_CHIP_VER_PENDING, &mrvl->flags);
 
 	hu->priv = mrvl;
+
+	if (hu->serdev) {
+		ret = serdev_device_open(hu->serdev);
+		if (ret)
+			goto err;
+	}
+
 	return 0;
+err:
+	kfree(mrvl);
+
+	return ret;
 }
 
 static int mrvl_close(struct hci_uart *hu)
@@ -71,6 +89,9 @@ static int mrvl_close(struct hci_uart *hu)
 
 	BT_DBG("hu %p", hu);
 
+	if (hu->serdev)
+		serdev_device_close(hu->serdev);
+
 	skb_queue_purge(&mrvl->txq);
 	skb_queue_purge(&mrvl->rawq);
 	kfree_skb(mrvl->rx_skb);
@@ -339,7 +360,14 @@ static int mrvl_setup(struct hci_uart *hu)
 		return -EINVAL;
 	}
 
-	hci_uart_set_baudrate(hu, 3000000);
+	/* Let the final ack go out before switching the baudrate */
+	hci_uart_wait_until_sent(hu);
+
+	if (hu->serdev)
+		serdev_device_set_baudrate(hu->serdev, 3000000);
+	else
+		hci_uart_set_baudrate(hu, 3000000);
+
 	hci_uart_set_flow_control(hu, false);
 
 	err = mrvl_load_firmware(hu->hdev, "mrvl/uart8897_bt.bin");
@@ -362,12 +390,54 @@ static const struct hci_uart_proto mrvl_proto = {
 	.dequeue	= mrvl_dequeue,
 };
 
+static int mrvl_serdev_probe(struct serdev_device *serdev)
+{
+	struct mrvl_serdev *mrvldev;
+
+	mrvldev = devm_kzalloc(&serdev->dev, sizeof(*mrvldev), GFP_KERNEL);
+	if (!mrvldev)
+		return -ENOMEM;
+
+	mrvldev->hu.serdev = serdev;
+	serdev_device_set_drvdata(serdev, mrvldev);
+
+	return hci_uart_register_device(&mrvldev->hu, &mrvl_proto);
+}
+
+static void mrvl_serdev_remove(struct serdev_device *serdev)
+{
+	struct mrvl_serdev *mrvldev = serdev_device_get_drvdata(serdev);
+
+	hci_uart_unregister_device(&mrvldev->hu);
+}
+
+#ifdef CONFIG_OF
+static const struct of_device_id mrvl_bluetooth_of_match[] = {
+	{ .compatible = "mrvl,88w8897" },
+	{ },
+};
+MODULE_DEVICE_TABLE(of, mrvl_bluetooth_of_match);
+#endif
+
+static struct serdev_device_driver mrvl_serdev_driver = {
+	.probe = mrvl_serdev_probe,
+	.remove = mrvl_serdev_remove,
+	.driver = {
+		.name = "hci_uart_mrvl",
+		.of_match_table = of_match_ptr(mrvl_bluetooth_of_match),
+	},
+};
+
 int __init mrvl_init(void)
 {
+	serdev_device_driver_register(&mrvl_serdev_driver);
+
 	return hci_uart_register_proto(&mrvl_proto);
 }
 
 int __exit mrvl_deinit(void)
 {
+	serdev_device_driver_unregister(&mrvl_serdev_driver);
+
 	return hci_uart_unregister_proto(&mrvl_proto);
 }

drivers/bluetooth/hci_qca.c

@@ -17,6 +17,7 @@
 
 #include <linux/kernel.h>
 #include <linux/clk.h>
+#include <linux/completion.h>
 #include <linux/debugfs.h>
 #include <linux/delay.h>
 #include <linux/device.h>
@@ -53,6 +54,7 @@
 
 enum qca_flags {
 	QCA_IBS_ENABLED,
+	QCA_DROP_VENDOR_EVENT,
 };
 
 /* HCI_IBS transmit side sleep protocol states */
@@ -97,6 +99,7 @@ struct qca_data {
 	struct work_struct ws_rx_vote_off;
 	struct work_struct ws_tx_vote_off;
 	unsigned long flags;
+	struct completion drop_ev_comp;
 
 	/* For debugging purpose */
 	u64 ibs_sent_wacks;
@@ -156,6 +159,7 @@ struct qca_serdev {
 	struct qca_power *bt_power;
 	u32 init_speed;
 	u32 oper_speed;
+	const char *firmware_name;
 };
 
 static int qca_power_setup(struct hci_uart *hu, bool on);
@@ -177,6 +181,17 @@ static enum qca_btsoc_type qca_soc_type(struct hci_uart *hu)
 	return soc_type;
 }
 
+static const char *qca_get_firmware_name(struct hci_uart *hu)
+{
+	if (hu->serdev) {
+		struct qca_serdev *qsd = serdev_device_get_drvdata(hu->serdev);
+
+		return qsd->firmware_name;
+	} else {
+		return NULL;
+	}
+}
+
 static void __serial_clock_on(struct tty_struct *tty)
 {
 	/* TODO: Some chipset requires to enable UART clock on client
@@ -478,6 +493,7 @@ static int qca_open(struct hci_uart *hu)
 	INIT_WORK(&qca->ws_tx_vote_off, qca_wq_serial_tx_clock_vote_off);
 
 	qca->hu = hu;
+	init_completion(&qca->drop_ev_comp);
 
 	/* Assume we start with both sides asleep -- extra wakes OK */
 	qca->tx_ibs_state = HCI_IBS_TX_ASLEEP;
@@ -872,6 +888,35 @@ static int qca_recv_acl_data(struct hci_dev *hdev, struct sk_buff *skb)
 	return hci_recv_frame(hdev, skb);
 }
 
+static int qca_recv_event(struct hci_dev *hdev, struct sk_buff *skb)
+{
+	struct hci_uart *hu = hci_get_drvdata(hdev);
+	struct qca_data *qca = hu->priv;
+
+	if (test_bit(QCA_DROP_VENDOR_EVENT, &qca->flags)) {
+		struct hci_event_hdr *hdr = (void *)skb->data;
+
+		/* For the WCN3990 the vendor command for a baudrate change
+		 * isn't sent as synchronous HCI command, because the
+		 * controller sends the corresponding vendor event with the
+		 * new baudrate. The event is received and properly decoded
+		 * after changing the baudrate of the host port. It needs to
+		 * be dropped, otherwise it can be misinterpreted as
+		 * response to a later firmware download command (also a
+		 * vendor command).
+		 */
+
+		if (hdr->evt == HCI_EV_VENDOR)
+			complete(&qca->drop_ev_comp);
+
+		kfree(skb);
+
+		return 0;
+	}
+
+	return hci_recv_frame(hdev, skb);
+}
+
 #define QCA_IBS_SLEEP_IND_EVENT \
 	.type = HCI_IBS_SLEEP_IND, \
 	.hlen = 0, \
@@ -896,7 +941,7 @@ static int qca_recv_acl_data(struct hci_dev *hdev, struct sk_buff *skb)
 static const struct h4_recv_pkt qca_recv_pkts[] = {
 	{ H4_RECV_ACL,             .recv = qca_recv_acl_data },
 	{ H4_RECV_SCO,             .recv = hci_recv_frame    },
-	{ H4_RECV_EVENT,           .recv = hci_recv_frame    },
+	{ H4_RECV_EVENT,           .recv = qca_recv_event    },
 	{ QCA_IBS_WAKE_IND_EVENT,  .recv = qca_ibs_wake_ind  },
 	{ QCA_IBS_WAKE_ACK_EVENT,  .recv = qca_ibs_wake_ack  },
 	{ QCA_IBS_SLEEP_IND_EVENT, .recv = qca_ibs_sleep_ind },
@@ -1091,6 +1136,7 @@ static int qca_check_speeds(struct hci_uart *hu)
 static int qca_set_speed(struct hci_uart *hu, enum qca_speed_type speed_type)
 {
 	unsigned int speed, qca_baudrate;
+	struct qca_data *qca = hu->priv;
 	int ret = 0;
 
 	if (speed_type == QCA_INIT_SPEED) {
@@ -1110,6 +1156,11 @@ static int qca_set_speed(struct hci_uart *hu, enum qca_speed_type speed_type)
 		if (qca_is_wcn399x(soc_type))
 			hci_uart_set_flow_control(hu, true);
 
+		if (soc_type == QCA_WCN3990) {
+			reinit_completion(&qca->drop_ev_comp);
+			set_bit(QCA_DROP_VENDOR_EVENT, &qca->flags);
+		}
+
 		qca_baudrate = qca_get_baudrate_value(speed);
 		bt_dev_dbg(hu->hdev, "Set UART speed to %d", speed);
 		ret = qca_set_baudrate(hu->hdev, qca_baudrate);
@@ -1121,6 +1172,20 @@ static int qca_set_speed(struct hci_uart *hu, enum qca_speed_type speed_type)
 error:
 		if (qca_is_wcn399x(soc_type))
 			hci_uart_set_flow_control(hu, false);
+
+		if (soc_type == QCA_WCN3990) {
+			/* Wait for the controller to send the vendor event
+			 * for the baudrate change command.
+			 */
+			if (!wait_for_completion_timeout(&qca->drop_ev_comp,
+						 msecs_to_jiffies(100))) {
+				bt_dev_err(hu->hdev,
+					   "Failed to change controller baudrate\n");
+				ret = -ETIMEDOUT;
+			}
+
+			clear_bit(QCA_DROP_VENDOR_EVENT, &qca->flags);
+		}
 	}
 
 	return ret;
@@ -1182,6 +1247,7 @@ static int qca_setup(struct hci_uart *hu)
 	struct qca_data *qca = hu->priv;
 	unsigned int speed, qca_baudrate = QCA_BAUDRATE_115200;
 	enum qca_btsoc_type soc_type = qca_soc_type(hu);
+	const char *firmware_name = qca_get_firmware_name(hu);
 	int ret;
 	int soc_ver = 0;
 
@@ -1232,7 +1298,8 @@ static int qca_setup(struct hci_uart *hu)
 
 	bt_dev_info(hdev, "QCA controller version 0x%08x", soc_ver);
 	/* Setup patch / NVM configurations */
-	ret = qca_uart_setup(hdev, qca_baudrate, soc_type, soc_ver);
+	ret = qca_uart_setup(hdev, qca_baudrate, soc_type, soc_ver,
+			firmware_name);
 	if (!ret) {
 		set_bit(QCA_IBS_ENABLED, &qca->flags);
 		qca_debugfs_init(hdev);
@@ -1426,6 +1493,8 @@ static int qca_serdev_probe(struct serdev_device *serdev)
 	qcadev->serdev_hu.serdev = serdev;
 	data = of_device_get_match_data(&serdev->dev);
 	serdev_device_set_drvdata(serdev, qcadev);
+	device_property_read_string(&serdev->dev, "firmware-name",
+					 &qcadev->firmware_name);
 	if (data && qca_is_wcn399x(data->soc_type)) {
 		qcadev->btsoc_type = data->soc_type;
 		qcadev->bt_power = devm_kzalloc(&serdev->dev,

drivers/bluetooth/hci_uart.h

@@ -100,6 +100,7 @@ int hci_uart_register_device(struct hci_uart *hu, const struct hci_uart_proto *p
 void hci_uart_unregister_device(struct hci_uart *hu);
 
 int hci_uart_tx_wakeup(struct hci_uart *hu);
+int hci_uart_wait_until_sent(struct hci_uart *hu);
 int hci_uart_init_ready(struct hci_uart *hu);
 void hci_uart_init_work(struct work_struct *work);
 void hci_uart_set_baudrate(struct hci_uart *hu, unsigned int speed);

include/net/bluetooth/hci.h

@@ -1143,6 +1143,26 @@ struct hci_cp_write_sc_support {
 	__u8	support;
 } __packed;
 
+#define HCI_OP_READ_AUTH_PAYLOAD_TO    0x0c7b
+struct hci_cp_read_auth_payload_to {
+	__le16  handle;
+} __packed;
+struct hci_rp_read_auth_payload_to {
+	__u8    status;
+	__le16  handle;
+	__le16  timeout;
+} __packed;
+
+#define HCI_OP_WRITE_AUTH_PAYLOAD_TO    0x0c7c
+struct hci_cp_write_auth_payload_to {
+	__le16  handle;
+	__le16  timeout;
+} __packed;
+struct hci_rp_write_auth_payload_to {
+	__u8    status;
+	__le16  handle;
+} __packed;
+
 #define HCI_OP_READ_LOCAL_OOB_EXT_DATA	0x0c7d
 struct hci_rp_read_local_oob_ext_data {
 	__u8     status;

include/net/bluetooth/hci_core.h

@@ -199,6 +199,8 @@ struct adv_info {
 /* Default min/max age of connection information (1s/3s) */
 #define DEFAULT_CONN_INFO_MIN_AGE	1000
 #define DEFAULT_CONN_INFO_MAX_AGE	3000
+/* Default authenticated payload timeout 30s */
+#define DEFAULT_AUTH_PAYLOAD_TIMEOUT   0x0bb8
 
 struct amp_assoc {
 	__u16	len;
@@ -275,6 +277,7 @@ struct hci_dev {
 	__u16		discov_interleaved_timeout;
 	__u16		conn_info_min_age;
 	__u16		conn_info_max_age;
+	__u16		auth_payload_timeout;
 	__u8		ssp_debug_mode;
 	__u8		hw_error_code;
 	__u32		clock;
@@ -481,6 +484,7 @@ struct hci_conn {
 	__u16		disc_timeout;
 	__u16		conn_timeout;
 	__u16		setting;
+	__u16		auth_payload_timeout;
 	__u16		le_conn_min_interval;
 	__u16		le_conn_max_interval;
 	__u16		le_conn_interval;

net/6lowpan/6lowpan_i.h

@@ -18,24 +18,16 @@ extern const struct ndisc_ops lowpan_ndisc_ops;
 int addrconf_ifid_802154_6lowpan(u8 *eui, struct net_device *dev);
 
 #ifdef CONFIG_6LOWPAN_DEBUGFS
-int lowpan_dev_debugfs_init(struct net_device *dev);
+void lowpan_dev_debugfs_init(struct net_device *dev);
 void lowpan_dev_debugfs_exit(struct net_device *dev);
 
-int __init lowpan_debugfs_init(void);
+void __init lowpan_debugfs_init(void);
 void lowpan_debugfs_exit(void);
 #else
-static inline int lowpan_dev_debugfs_init(struct net_device *dev)
-{
-	return 0;
-}
-
+static inline void lowpan_dev_debugfs_init(struct net_device *dev) { }
 static inline void lowpan_dev_debugfs_exit(struct net_device *dev) { }
 
-static inline int __init lowpan_debugfs_init(void)
-{
-	return 0;
-}
-
+static inline void __init lowpan_debugfs_init(void) { }
 static inline void lowpan_debugfs_exit(void) { }
 #endif /* CONFIG_6LOWPAN_DEBUGFS */
 

net/6lowpan/core.c

@@ -42,9 +42,7 @@ int lowpan_register_netdevice(struct net_device *dev,
 	if (ret < 0)
 		return ret;
 
-	ret = lowpan_dev_debugfs_init(dev);
-	if (ret < 0)
-		unregister_netdevice(dev);
+	lowpan_dev_debugfs_init(dev);
 
 	return ret;
 }
@@ -152,9 +150,7 @@ static int __init lowpan_module_init(void)
 {
 	int ret;
 
-	ret = lowpan_debugfs_init();
-	if (ret < 0)
-		return ret;
+	lowpan_debugfs_init();
 
 	ret = register_netdevice_notifier(&lowpan_notifier);
 	if (ret < 0) {

net/6lowpan/debugfs.c

@@ -163,11 +163,11 @@ static const struct file_operations lowpan_ctx_pfx_fops = {
 	.release	= single_release,
 };
 
-static int lowpan_dev_debugfs_ctx_init(struct net_device *dev,
-				       struct dentry *ctx, u8 id)
+static void lowpan_dev_debugfs_ctx_init(struct net_device *dev,
+					struct dentry *ctx, u8 id)
 {
 	struct lowpan_dev *ldev = lowpan_dev(dev);
-	struct dentry *dentry, *root;
+	struct dentry *root;
 	char buf[32];
 
 	WARN_ON_ONCE(id > LOWPAN_IPHC_CTX_TABLE_SIZE);
@@ -175,34 +175,18 @@ static int lowpan_dev_debugfs_ctx_init(struct net_device *dev,
 	sprintf(buf, "%d", id);
 
 	root = debugfs_create_dir(buf, ctx);
-	if (!root)
-		return -EINVAL;
 
-	dentry = debugfs_create_file_unsafe("active", 0644, root,
-					    &ldev->ctx.table[id],
-					    &lowpan_ctx_flag_active_fops);
-	if (!dentry)
-		return -EINVAL;
+	debugfs_create_file("active", 0644, root, &ldev->ctx.table[id],
+			    &lowpan_ctx_flag_active_fops);
 
-	dentry = debugfs_create_file_unsafe("compression", 0644, root,
-					    &ldev->ctx.table[id],
-					    &lowpan_ctx_flag_c_fops);
-	if (!dentry)
-		return -EINVAL;
-
-	dentry = debugfs_create_file("prefix", 0644, root,
-				     &ldev->ctx.table[id],
-				     &lowpan_ctx_pfx_fops);
-	if (!dentry)
-		return -EINVAL;
+	debugfs_create_file("compression", 0644, root, &ldev->ctx.table[id],
+			    &lowpan_ctx_flag_c_fops);
 
-	dentry = debugfs_create_file_unsafe("prefix_len", 0644, root,
-					    &ldev->ctx.table[id],
-					    &lowpan_ctx_plen_fops);
-	if (!dentry)
-		return -EINVAL;
+	debugfs_create_file("prefix", 0644, root, &ldev->ctx.table[id],
+			    &lowpan_ctx_pfx_fops);
 
-	return 0;
+	debugfs_create_file("prefix_len", 0644, root, &ldev->ctx.table[id],
+			    &lowpan_ctx_plen_fops);
 }
 
 static int lowpan_context_show(struct seq_file *file, void *offset)
@@ -242,64 +226,39 @@ static int lowpan_short_addr_get(void *data, u64 *val)
 DEFINE_DEBUGFS_ATTRIBUTE(lowpan_short_addr_fops, lowpan_short_addr_get, NULL,
 			 "0x%04llx\n");
 
-static int lowpan_dev_debugfs_802154_init(const struct net_device *dev,
+static void lowpan_dev_debugfs_802154_init(const struct net_device *dev,
 					  struct lowpan_dev *ldev)
 {
-	struct dentry *dentry, *root;
+	struct dentry *root;
 
 	if (!lowpan_is_ll(dev, LOWPAN_LLTYPE_IEEE802154))
-		return 0;
+		return;
 
 	root = debugfs_create_dir("ieee802154", ldev->iface_debugfs);
-	if (!root)
-		return -EINVAL;
-
-	dentry = debugfs_create_file_unsafe("short_addr", 0444, root,
-					    lowpan_802154_dev(dev)->wdev->ieee802154_ptr,
-					    &lowpan_short_addr_fops);
-	if (!dentry)
-		return -EINVAL;
 
-	return 0;
+	debugfs_create_file("short_addr", 0444, root,
+			    lowpan_802154_dev(dev)->wdev->ieee802154_ptr,
+			    &lowpan_short_addr_fops);
 }
 
-int lowpan_dev_debugfs_init(struct net_device *dev)
+void lowpan_dev_debugfs_init(struct net_device *dev)
 {
 	struct lowpan_dev *ldev = lowpan_dev(dev);
-	struct dentry *contexts, *dentry;
-	int ret, i;
+	struct dentry *contexts;
+	int i;
 
 	/* creating the root */
 	ldev->iface_debugfs = debugfs_create_dir(dev->name, lowpan_debugfs);
-	if (!ldev->iface_debugfs)
-		goto fail;
 
 	contexts = debugfs_create_dir("contexts", ldev->iface_debugfs);
-	if (!contexts)
-		goto remove_root;
-
-	dentry = debugfs_create_file("show", 0644, contexts,
-				     &lowpan_dev(dev)->ctx,
-				     &lowpan_context_fops);
-	if (!dentry)
-		goto remove_root;
-
-	for (i = 0; i < LOWPAN_IPHC_CTX_TABLE_SIZE; i++) {
-		ret = lowpan_dev_debugfs_ctx_init(dev, contexts, i);
-		if (ret < 0)
-			goto remove_root;
-	}
 
-	ret = lowpan_dev_debugfs_802154_init(dev, ldev);
-	if (ret < 0)
-		goto remove_root;
+	debugfs_create_file("show", 0644, contexts, &lowpan_dev(dev)->ctx,
+			    &lowpan_context_fops);
 
-	return 0;
+	for (i = 0; i < LOWPAN_IPHC_CTX_TABLE_SIZE; i++)
+		lowpan_dev_debugfs_ctx_init(dev, contexts, i);
 
-remove_root:
-	lowpan_dev_debugfs_exit(dev);
-fail:
-	return -EINVAL;
+	lowpan_dev_debugfs_802154_init(dev, ldev);
 }
 
 void lowpan_dev_debugfs_exit(struct net_device *dev)
@@ -307,13 +266,9 @@ void lowpan_dev_debugfs_exit(struct net_device *dev)
 	debugfs_remove_recursive(lowpan_dev(dev)->iface_debugfs);
 }
 
-int __init lowpan_debugfs_init(void)
+void __init lowpan_debugfs_init(void)
 {
 	lowpan_debugfs = debugfs_create_dir("6lowpan", NULL);
-	if (!lowpan_debugfs)
-		return -EINVAL;
-
-	return 0;
 }
 
 void lowpan_debugfs_exit(void)

net/bluetooth/6lowpan.c

@@ -164,26 +164,21 @@ static inline struct lowpan_peer *peer_lookup_dst(struct lowpan_btle_dev *dev,
 	int count = atomic_read(&dev->peer_count);
 	const struct in6_addr *nexthop;
 	struct lowpan_peer *peer;
+	struct neighbour *neigh;
 
 	BT_DBG("peers %d addr %pI6c rt %p", count, daddr, rt);
 
-	/* If we have multiple 6lowpan peers, then check where we should
-	 * send the packet. If only one peer exists, then we can send the
-	 * packet right away.
-	 */
-	if (count == 1) {
-		rcu_read_lock();
-		peer = list_first_or_null_rcu(&dev->peers, struct lowpan_peer,
-					      list);
-		rcu_read_unlock();
-		return peer;
-	}
-
 	if (!rt) {
-		nexthop = &lowpan_cb(skb)->gw;
-
-		if (ipv6_addr_any(nexthop))
-			return NULL;
+		if (ipv6_addr_any(&lowpan_cb(skb)->gw)) {
+			/* There is neither route nor gateway,
+			 * probably the destination is a direct peer.
+			 */
+			nexthop = daddr;
+		} else {
+			/* There is a known gateway
+			 */
+			nexthop = &lowpan_cb(skb)->gw;
+		}
 	} else {
 		nexthop = rt6_nexthop(rt, daddr);
 
@@ -209,6 +204,20 @@ static inline struct lowpan_peer *peer_lookup_dst(struct lowpan_btle_dev *dev,
 		}
 	}
 
+	/* use the neighbour cache for matching addresses assigned by SLAAC
+	*/
+	neigh = __ipv6_neigh_lookup(dev->netdev, nexthop);
+	if (neigh) {
+		list_for_each_entry_rcu(peer, &dev->peers, list) {
+			if (!memcmp(neigh->ha, peer->lladdr, ETH_ALEN)) {
+				neigh_release(neigh);
+				rcu_read_unlock();
+				return peer;
+			}
+		}
+		neigh_release(neigh);
+	}
+
 	rcu_read_unlock();
 
 	return NULL;

net/bluetooth/hci_conn.c

@@ -520,6 +520,9 @@ struct hci_conn *hci_conn_add(struct hci_dev *hdev, int type, bdaddr_t *dst,
 	set_bit(HCI_CONN_POWER_SAVE, &conn->flags);
 	conn->disc_timeout = HCI_DISCONN_TIMEOUT;
 
+	/* Set Default Authenticated payload timeout to 30s */
+	conn->auth_payload_timeout = DEFAULT_AUTH_PAYLOAD_TIMEOUT;
+
 	if (conn->role == HCI_ROLE_MASTER)
 		conn->out = true;
 
@@ -912,7 +915,7 @@ static void hci_req_directed_advertising(struct hci_request *req,
 				    sizeof(cp), &cp);
 		}
 
-		__hci_req_enable_ext_advertising(req);
+		__hci_req_enable_ext_advertising(req, 0x00);
 	} else {
 		struct hci_cp_le_set_adv_param cp;
 

net/bluetooth/hci_core.c

@@ -2827,7 +2827,7 @@ int hci_add_adv_instance(struct hci_dev *hdev, u8 instance, u32 flags,
 		memset(adv_instance->scan_rsp_data, 0,
 		       sizeof(adv_instance->scan_rsp_data));
 	} else {
-		if (hdev->adv_instance_cnt >= HCI_MAX_ADV_INSTANCES ||
+		if (hdev->adv_instance_cnt >= hdev->le_num_of_adv_sets ||
 		    instance < 1 || instance > HCI_MAX_ADV_INSTANCES)
 			return -EOVERFLOW;
 
@@ -3195,11 +3195,13 @@ struct hci_dev *hci_alloc_dev(void)
 	hdev->le_min_key_size = SMP_MIN_ENC_KEY_SIZE;
 	hdev->le_tx_def_phys = HCI_LE_SET_PHY_1M;
 	hdev->le_rx_def_phys = HCI_LE_SET_PHY_1M;
+	hdev->le_num_of_adv_sets = HCI_MAX_ADV_INSTANCES;
 
 	hdev->rpa_timeout = HCI_DEFAULT_RPA_TIMEOUT;
 	hdev->discov_interleaved_timeout = DISCOV_INTERLEAVED_TIMEOUT;
 	hdev->conn_info_min_age = DEFAULT_CONN_INFO_MIN_AGE;
 	hdev->conn_info_max_age = DEFAULT_CONN_INFO_MAX_AGE;
+	hdev->auth_payload_timeout = DEFAULT_AUTH_PAYLOAD_TIMEOUT;
 
 	mutex_init(&hdev->lock);
 	mutex_init(&hdev->req_lock);

net/bluetooth/hci_debugfs.c

@@ -941,6 +941,35 @@ static int adv_max_interval_get(void *data, u64 *val)
 DEFINE_SIMPLE_ATTRIBUTE(adv_max_interval_fops, adv_max_interval_get,
 			adv_max_interval_set, "%llu\n");
 
+static int auth_payload_timeout_set(void *data, u64 val)
+{
+	struct hci_dev *hdev = data;
+
+	if (val < 0x0001 || val > 0xffff)
+		return -EINVAL;
+
+	hci_dev_lock(hdev);
+	hdev->auth_payload_timeout = val;
+	hci_dev_unlock(hdev);
+
+	return 0;
+}
+
+static int auth_payload_timeout_get(void *data, u64 *val)
+{
+	struct hci_dev *hdev = data;
+
+	hci_dev_lock(hdev);
+	*val = hdev->auth_payload_timeout;
+	hci_dev_unlock(hdev);
+
+	return 0;
+}
+
+DEFINE_SIMPLE_ATTRIBUTE(auth_payload_timeout_fops,
+			auth_payload_timeout_get,
+			auth_payload_timeout_set, "%llu\n");
+
 DEFINE_QUIRK_ATTRIBUTE(quirk_strict_duplicate_filter,
 		       HCI_QUIRK_STRICT_DUPLICATE_FILTER);
 DEFINE_QUIRK_ATTRIBUTE(quirk_simultaneous_discovery,
@@ -994,6 +1023,8 @@ void hci_debugfs_create_le(struct hci_dev *hdev)
 			    &adv_max_interval_fops);
 	debugfs_create_u16("discov_interleaved_timeout", 0644, hdev->debugfs,
 			   &hdev->discov_interleaved_timeout);
+	debugfs_create_file("auth_payload_timeout", 0644, hdev->debugfs, hdev,
+			    &auth_payload_timeout_fops);
 
 	debugfs_create_file("quirk_strict_duplicate_filter", 0644,
 			    hdev->debugfs, hdev,

net/bluetooth/hci_event.c

@@ -579,6 +579,51 @@ static void hci_cc_read_local_commands(struct hci_dev *hdev,
 		memcpy(hdev->commands, rp->commands, sizeof(hdev->commands));
 }
 
+static void hci_cc_read_auth_payload_timeout(struct hci_dev *hdev,
+					     struct sk_buff *skb)
+{
+	struct hci_rp_read_auth_payload_to *rp = (void *)skb->data;
+	struct hci_conn *conn;
+
+	BT_DBG("%s status 0x%2.2x", hdev->name, rp->status);
+
+	if (rp->status)
+		return;
+
+	hci_dev_lock(hdev);
+
+	conn = hci_conn_hash_lookup_handle(hdev, __le16_to_cpu(rp->handle));
+	if (conn)
+		conn->auth_payload_timeout = __le16_to_cpu(rp->timeout);
+
+	hci_dev_unlock(hdev);
+}
+
+static void hci_cc_write_auth_payload_timeout(struct hci_dev *hdev,
+					      struct sk_buff *skb)
+{
+	struct hci_rp_write_auth_payload_to *rp = (void *)skb->data;
+	struct hci_conn *conn;
+	void *sent;
+
+	BT_DBG("%s status 0x%2.2x", hdev->name, rp->status);
+
+	if (rp->status)
+		return;
+
+	sent = hci_sent_cmd_data(hdev, HCI_OP_WRITE_AUTH_PAYLOAD_TO);
+	if (!sent)
+		return;
+
+	hci_dev_lock(hdev);
+
+	conn = hci_conn_hash_lookup_handle(hdev, __le16_to_cpu(rp->handle));
+	if (conn)
+		conn->auth_payload_timeout = get_unaligned_le16(sent + 2);
+
+	hci_dev_unlock(hdev);
+}
+
 static void hci_cc_read_local_features(struct hci_dev *hdev,
 				       struct sk_buff *skb)
 {
@@ -2975,6 +3020,25 @@ static void hci_encrypt_change_evt(struct hci_dev *hdev, struct sk_buff *skb)
 		goto unlock;
 	}
 
+	/* Set the default Authenticated Payload Timeout after
+	 * an LE Link is established. As per Core Spec v5.0, Vol 2, Part B
+	 * Section 3.3, the HCI command WRITE_AUTH_PAYLOAD_TIMEOUT should be
+	 * sent when the link is active and Encryption is enabled, the conn
+	 * type can be either LE or ACL and controller must support LMP Ping.
+	 * Ensure for AES-CCM encryption as well.
+	 */
+	if (test_bit(HCI_CONN_ENCRYPT, &conn->flags) &&
+	    test_bit(HCI_CONN_AES_CCM, &conn->flags) &&
+	    ((conn->type == ACL_LINK && lmp_ping_capable(hdev)) ||
+	     (conn->type == LE_LINK && (hdev->le_features[0] & HCI_LE_PING)))) {
+		struct hci_cp_write_auth_payload_to cp;
+
+		cp.handle = cpu_to_le16(conn->handle);
+		cp.timeout = cpu_to_le16(hdev->auth_payload_timeout);
+		hci_send_cmd(conn->hdev, HCI_OP_WRITE_AUTH_PAYLOAD_TO,
+			     sizeof(cp), &cp);
+	}
+
 notify:
 	if (conn->state == BT_CONFIG) {
 		if (!ev->status)
@@ -3170,6 +3234,14 @@ static void hci_cmd_complete_evt(struct hci_dev *hdev, struct sk_buff *skb,
 		hci_cc_write_sc_support(hdev, skb);
 		break;
 
+	case HCI_OP_READ_AUTH_PAYLOAD_TO:
+		hci_cc_read_auth_payload_timeout(hdev, skb);
+		break;
+
+	case HCI_OP_WRITE_AUTH_PAYLOAD_TO:
+		hci_cc_write_auth_payload_timeout(hdev, skb);
+		break;
+
 	case HCI_OP_READ_LOCAL_VERSION:
 		hci_cc_read_local_version(hdev, skb);
 		break;
@@ -5588,6 +5660,11 @@ static void hci_le_remote_conn_param_req_evt(struct hci_dev *hdev,
 		return send_conn_param_neg_reply(hdev, handle,
 						 HCI_ERROR_UNKNOWN_CONN_ID);
 
+	if (min < hcon->le_conn_min_interval ||
+	    max > hcon->le_conn_max_interval)
+		return send_conn_param_neg_reply(hdev, handle,
+						 HCI_ERROR_INVALID_LL_PARAMS);
+
 	if (hci_check_conn_params(min, max, latency, timeout))
 		return send_conn_param_neg_reply(hdev, handle,
 						 HCI_ERROR_INVALID_LL_PARAMS);

net/bluetooth/hci_request.c

@@ -1601,7 +1601,7 @@ int __hci_req_setup_ext_adv_instance(struct hci_request *req, u8 instance)
 	cp.own_addr_type = own_addr_type;
 	cp.channel_map = hdev->le_adv_channel_map;
 	cp.tx_power = 127;
-	cp.handle = 0;
+	cp.handle = instance;
 
 	if (flags & MGMT_ADV_FLAG_SEC_2M) {
 		cp.primary_phy = HCI_ADV_PHY_1M;
@@ -1643,11 +1643,21 @@ int __hci_req_setup_ext_adv_instance(struct hci_request *req, u8 instance)
 	return 0;
 }
 
-void __hci_req_enable_ext_advertising(struct hci_request *req)
+int __hci_req_enable_ext_advertising(struct hci_request *req, u8 instance)
 {
+	struct hci_dev *hdev = req->hdev;
 	struct hci_cp_le_set_ext_adv_enable *cp;
 	struct hci_cp_ext_adv_set *adv_set;
 	u8 data[sizeof(*cp) + sizeof(*adv_set) * 1];
+	struct adv_info *adv_instance;
+
+	if (instance > 0) {
+		adv_instance = hci_find_adv_instance(hdev, instance);
+		if (!adv_instance)
+			return -EINVAL;
+	} else {
+		adv_instance = NULL;
+	}
 
 	cp = (void *) data;
 	adv_set = (void *) cp->data;
@@ -1659,11 +1669,23 @@ void __hci_req_enable_ext_advertising(struct hci_request *req)
 
 	memset(adv_set, 0, sizeof(*adv_set));
 
-	adv_set->handle = 0;
+	adv_set->handle = instance;
+
+	/* Set duration per instance since controller is responsible for
+	 * scheduling it.
+	 */
+	if (adv_instance && adv_instance->duration) {
+		u16 duration = adv_instance->duration * MSEC_PER_SEC;
+
+		/* Time = N * 10 ms */
+		adv_set->duration = cpu_to_le16(duration / 10);
+	}
 
 	hci_req_add(req, HCI_OP_LE_SET_EXT_ADV_ENABLE,
 		    sizeof(*cp) + sizeof(*adv_set) * cp->num_of_sets,
 		    data);
+
+	return 0;
 }
 
 int __hci_req_start_ext_adv(struct hci_request *req, u8 instance)
@@ -1679,7 +1701,7 @@ int __hci_req_start_ext_adv(struct hci_request *req, u8 instance)
 		return err;
 
 	__hci_req_update_scan_rsp_data(req, instance);
-	__hci_req_enable_ext_advertising(req);
+	__hci_req_enable_ext_advertising(req, instance);
 
 	return 0;
 }
@@ -1723,10 +1745,13 @@ int __hci_req_schedule_adv_instance(struct hci_request *req, u8 instance,
 		adv_instance->remaining_time =
 				adv_instance->remaining_time - timeout;
 
-	hdev->adv_instance_timeout = timeout;
-	queue_delayed_work(hdev->req_workqueue,
+	/* Only use work for scheduling instances with legacy advertising */
+	if (!ext_adv_capable(hdev)) {
+		hdev->adv_instance_timeout = timeout;
+		queue_delayed_work(hdev->req_workqueue,
 			   &hdev->adv_instance_expire,
 			   msecs_to_jiffies(timeout * 1000));
+	}
 
 	/* If we're just re-scheduling the same instance again then do not
 	 * execute any HCI commands. This happens when a single instance is
@@ -2744,7 +2769,8 @@ static int powered_update_hci(struct hci_request *req, unsigned long opt)
 				if (!ext_adv_capable(hdev))
 					__hci_req_enable_advertising(req);
 				else if (!err)
-					__hci_req_enable_ext_advertising(req);
+					__hci_req_enable_ext_advertising(req,
+									 0x00);
 			}
 		} else if (!list_empty(&hdev->adv_instances)) {
 			struct adv_info *adv_instance;

net/bluetooth/hci_request.h

@@ -83,7 +83,7 @@ void hci_req_clear_adv_instance(struct hci_dev *hdev, struct sock *sk,
 
 int __hci_req_setup_ext_adv_instance(struct hci_request *req, u8 instance);
 int __hci_req_start_ext_adv(struct hci_request *req, u8 instance);
-void __hci_req_enable_ext_advertising(struct hci_request *req);
+int __hci_req_enable_ext_advertising(struct hci_request *req, u8 instance);
 void __hci_req_clear_ext_adv_sets(struct hci_request *req);
 int hci_get_random_address(struct hci_dev *hdev, bool require_privacy,
 			   bool use_rpa, struct adv_info *adv_instance,

net/bluetooth/hidp/core.c

@@ -775,7 +775,7 @@ static int hidp_setup_hid(struct hidp_session *session,
 	hid->version = req->version;
 	hid->country = req->country;
 
-	strncpy(hid->name, req->name, sizeof(hid->name));
+	strscpy(hid->name, req->name, sizeof(hid->name));
 
 	snprintf(hid->phys, sizeof(hid->phys), "%pMR",
 		 &l2cap_pi(session->ctrl_sock->sk)->chan->src);

net/bluetooth/hidp/sock.c

@@ -192,6 +192,7 @@ static int hidp_sock_compat_ioctl(struct socket *sock, unsigned int cmd, unsigne
 		ca.version = ca32.version;
 		ca.flags = ca32.flags;
 		ca.idle_to = ca32.idle_to;
+		ca32.name[sizeof(ca32.name) - 1] = '\0';
 		memcpy(ca.name, ca32.name, 128);
 
 		csock = sockfd_lookup(ca.ctrl_sock, &err);

net/bluetooth/l2cap_core.c

@@ -168,11 +168,18 @@ static struct l2cap_chan *l2cap_get_chan_by_ident(struct l2cap_conn *conn,
 	return c;
 }
 
-static struct l2cap_chan *__l2cap_global_chan_by_addr(__le16 psm, bdaddr_t *src)
+static struct l2cap_chan *__l2cap_global_chan_by_addr(__le16 psm, bdaddr_t *src,
+						      u8 src_type)
 {
 	struct l2cap_chan *c;
 
 	list_for_each_entry(c, &chan_list, global_l) {
+		if (src_type == BDADDR_BREDR && c->src_type != BDADDR_BREDR)
+			continue;
+
+		if (src_type != BDADDR_BREDR && c->src_type == BDADDR_BREDR)
+			continue;
+
 		if (c->sport == psm && !bacmp(&c->src, src))
 			return c;
 	}
@@ -185,7 +192,7 @@ int l2cap_add_psm(struct l2cap_chan *chan, bdaddr_t *src, __le16 psm)
 
 	write_lock(&chan_list_lock);
 
-	if (psm && __l2cap_global_chan_by_addr(psm, src)) {
+	if (psm && __l2cap_global_chan_by_addr(psm, src, chan->src_type)) {
 		err = -EADDRINUSE;
 		goto done;
 	}
@@ -209,7 +216,8 @@ int l2cap_add_psm(struct l2cap_chan *chan, bdaddr_t *src, __le16 psm)
 
 		err = -EINVAL;
 		for (p = start; p <= end; p += incr)
-			if (!__l2cap_global_chan_by_addr(cpu_to_le16(p), src)) {
+			if (!__l2cap_global_chan_by_addr(cpu_to_le16(p), src,
+							 chan->src_type)) {
 				chan->psm   = cpu_to_le16(p);
 				chan->sport = cpu_to_le16(p);
 				err = 0;
@@ -4394,6 +4402,12 @@ static inline int l2cap_disconnect_rsp(struct l2cap_conn *conn,
 
 	l2cap_chan_lock(chan);
 
+	if (chan->state != BT_DISCONN) {
+		l2cap_chan_unlock(chan);
+		mutex_unlock(&conn->chan_lock);
+		return 0;
+	}
+
 	l2cap_chan_hold(chan);
 	l2cap_chan_del(chan, 0);
 
@@ -5291,7 +5305,14 @@ static inline int l2cap_conn_param_update_req(struct l2cap_conn *conn,
 
 	memset(&rsp, 0, sizeof(rsp));
 
-	err = hci_check_conn_params(min, max, latency, to_multiplier);
+	if (min < hcon->le_conn_min_interval ||
+	    max > hcon->le_conn_max_interval) {
+		BT_DBG("requested connection interval exceeds current bounds.");
+		err = -EINVAL;
+	} else {
+		err = hci_check_conn_params(min, max, latency, to_multiplier);
+	}
+
 	if (err)
 		rsp.result = cpu_to_le16(L2CAP_CONN_PARAM_REJECTED);
 	else

net/bluetooth/smp.c

@@ -2579,6 +2579,19 @@ static int smp_cmd_ident_addr_info(struct l2cap_conn *conn,
 		goto distribute;
 	}
 
+	/* Drop IRK if peer is using identity address during pairing but is
+	 * providing different address as identity information.
+	 *
+	 * Microsoft Surface Precision Mouse is known to have this bug.
+	 */
+	if (hci_is_identity_address(&hcon->dst, hcon->dst_type) &&
+	    (bacmp(&info->bdaddr, &hcon->dst) ||
+	     info->addr_type != hcon->dst_type)) {
+		bt_dev_err(hcon->hdev,
+			   "ignoring IRK with invalid identity address");
+		goto distribute;
+	}
+
 	bacpy(&smp->id_addr, &info->bdaddr);
 	smp->id_addr_type = info->addr_type;