Merge branch 'avr32-arch' of git://git.kernel.org/pub/scm/linux/kernel/git/hskinnemoen/avr32-2.6

arch/avr32/boards/atngw100/Kconfig

@@ -2,8 +2,15 @@
 
 if BOARD_ATNGW100
 
+choice
+	prompt "Select an NGW100 add-on board to support"
+	default BOARD_ATNGW100_ADDON_NONE
+
+config BOARD_ATNGW100_ADDON_NONE
+	bool "None"
+
 config BOARD_ATNGW100_EVKLCD10X
-	bool "Add support for EVKLCD10X addon board"
+	bool "EVKLCD10X addon board"
 	help
 	  This enables support for the EVKLCD100 (QVGA) or EVKLCD101 (VGA)
 	  addon board for the NGW100. By enabling this the LCD controller and
@@ -14,7 +21,19 @@ config BOARD_ATNGW100_EVKLCD10X
 	  The MCI pins can be reenabled by editing the "add device function" but
 	  this may break the setup for other displays that use these pins.
 
-	  Choose 'Y' here if you have a EVKLCD100/101 connected to the NGW100.
+config BOARD_ATNGW100_MRMT
+	bool "Mediama RMT1/2 add-on board"
+	help
+	  This enables support for the Mediama RMT1 or RMT2 board.
+	  RMT provides LCD support, AC97 codec and other
+	  optional peripherals to the Atmel NGW100.
+
+	  This choice disables the detect pin and the write-protect pin for the
+	  MCI platform device, since it conflicts with the LCD platform device.
+	  The MCI pins can be reenabled by editing the "add device function" but
+	  this may break the setup for other displays that use these pins.
+
+endchoice
 
 choice
 	prompt "LCD panel resolution on EVKLCD10X"
@@ -32,4 +51,8 @@ config BOARD_ATNGW100_EVKLCD10X_POW_QVGA
 
 endchoice
 
+if BOARD_ATNGW100_MRMT
+source	"arch/avr32/boards/atngw100/Kconfig_mrmt"
+endif
+
 endif	# BOARD_ATNGW100

arch/avr32/boards/atngw100/Kconfig_mrmt

+# RMT for NGW100 customization
+
+choice
+	prompt "RMT Version"
+	help
+	  Select the RMTx board version.
+
+config BOARD_MRMT_REV1
+	bool "RMT1"
+config BOARD_MRMT_REV2
+	bool "RMT2"
+
+endchoice
+
+config BOARD_MRMT_AC97
+	bool "Enable AC97 CODEC"
+	help
+	  Enable the UCB1400 AC97 CODEC driver.
+
+choice
+	prompt "Touchscreen Driver"
+	default BOARD_MRMT_ADS7846_TS
+
+config BOARD_MRMT_UCB1400_TS
+	bool "Use UCB1400 Touchscreen"
+
+config BOARD_MRMT_ADS7846_TS
+	bool "Use ADS7846 Touchscreen"
+
+endchoice
+
+choice
+	prompt "RMTx LCD Selection"
+	default BOARD_MRMT_LCD_DISABLE
+
+config BOARD_MRMT_LCD_DISABLE
+	bool "LCD Disabled"
+
+config BOARD_MRMT_LCD_LQ043T3DX0X
+	bool "Sharp LQ043T3DX0x or compatible"
+	help
+	  If using RMT2, be sure to load the resistor pack selectors accordingly
+
+if BOARD_MRMT_REV2
+config BOARD_MRMT_LCD_KWH043GM08
+	bool "Formike KWH043GM08 or compatible"
+	help
+	  Be sure to load the RMT2 resistor pack selectors accordingly
+endif
+
+endchoice
+
+if !BOARD_MRMT_LCD_DISABLE
+config BOARD_MRMT_BL_PWM
+	bool "Use PWM control for LCD Backlight"
+	help
+		Use PWM driver for controlling LCD Backlight.
+		Otherwise, LCD Backlight is always on.
+endif
+
+config BOARD_MRMT_RTC_I2C
+	bool "Use External RTC on I2C Bus"
+	help
+		RMT1 has an optional RTC device on the I2C bus.
+		It is a SII S35390A.  Be sure to select the
+		matching RTC driver.
+
+choice
+	prompt "Wireless Module on ttyS2"
+	default BOARD_MRMT_WIRELESS_ZB
+
+config BOARD_MRMT_WIRELESS_ZB
+	bool "Use ZigBee/802.15.4 Module"
+
+config BOARD_MRMT_WIRELESS_BT
+	bool "Use Bluetooth (HCI) Module"
+
+config BOARD_MRMT_WIRELESS_NONE
+	bool "Not Installed"
+endchoice

arch/avr32/boards/atngw100/Makefile

 obj-y					+= setup.o flash.o
 obj-$(CONFIG_BOARD_ATNGW100_EVKLCD10X)	+= evklcd10x.o
+obj-$(CONFIG_BOARD_ATNGW100_MRMT)	+= mrmt.o

arch/avr32/boards/atngw100/mrmt.c

+/*
+ * Board-specific setup code for Remote Media Terminal 1 (RMT1)
+ * add-on board for the ATNGW100 Network Gateway
+ *
+ * Copyright (C) 2008 Mediama Technologies
+ * Based on ATNGW100 Network Gateway (Copyright (C) Atmel)
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#include <linux/gpio.h>
+#include <linux/init.h>
+#include <linux/irq.h>
+#include <linux/linkage.h>
+#include <linux/platform_device.h>
+#include <linux/types.h>
+#include <linux/fb.h>
+#include <linux/leds.h>
+#include <linux/input.h>
+#include <linux/gpio_keys.h>
+#include <linux/atmel_serial.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/ads7846.h>
+
+#include <video/atmel_lcdc.h>
+#include <sound/atmel-ac97c.h>
+
+#include <asm/delay.h>
+#include <asm/io.h>
+#include <asm/setup.h>
+
+#include <mach/at32ap700x.h>
+#include <mach/board.h>
+#include <mach/init.h>
+#include <mach/portmux.h>
+
+/* Define board-specifoic GPIO assignments */
+#define PIN_LCD_BL	GPIO_PIN_PA(28)
+#define PWM_CH_BL	0	/* Must match with GPIO pin definition */
+#define PIN_LCD_DISP	GPIO_PIN_PA(31)
+#define	PIN_AC97_RST_N	GPIO_PIN_PA(30)
+#define PB_EXTINT_BASE	25
+#define TS_IRQ		0
+#define PIN_TS_EXTINT	GPIO_PIN_PB(PB_EXTINT_BASE+TS_IRQ)
+#define PIN_PB_LEFT	GPIO_PIN_PB(11)
+#define PIN_PB_RIGHT	GPIO_PIN_PB(12)
+#define PIN_PWR_SW_N	GPIO_PIN_PB(14)
+#define PIN_PWR_ON	GPIO_PIN_PB(13)
+#define PIN_ZB_RST_N	GPIO_PIN_PA(21)
+#define PIN_BT_RST	GPIO_PIN_PA(22)
+#define PIN_LED_SYS	GPIO_PIN_PA(16)
+#define PIN_LED_A	GPIO_PIN_PA(19)
+#define PIN_LED_B	GPIO_PIN_PE(19)
+
+#ifdef CONFIG_BOARD_MRMT_LCD_LQ043T3DX0X
+/* Sharp LQ043T3DX0x (or compatible) panel */
+static struct fb_videomode __initdata lcd_fb_modes[] = {
+	{
+		.name		= "480x272 @ 59.94Hz",
+		.refresh	= 59.94,
+		.xres		= 480,		.yres		= 272,
+		.pixclock	= KHZ2PICOS(9000),
+
+		.left_margin	= 2,		.right_margin	= 2,
+		.upper_margin	= 3,		.lower_margin	= 9,
+		.hsync_len	= 41,		.vsync_len	= 1,
+
+		.sync		= 0,
+		.vmode		= FB_VMODE_NONINTERLACED,
+	},
+};
+
+static struct fb_monspecs __initdata lcd_fb_default_monspecs = {
+	.manufacturer		= "SHA",
+	.monitor		= "LQ043T3DX02",
+	.modedb			= lcd_fb_modes,
+	.modedb_len		= ARRAY_SIZE(lcd_fb_modes),
+	.hfmin			= 14915,
+	.hfmax			= 17638,
+	.vfmin			= 53,
+	.vfmax			= 61,
+	.dclkmax		= 9260000,
+};
+
+static struct atmel_lcdfb_info __initdata rmt_lcdc_data = {
+	.default_bpp		= 24,
+	.default_dmacon		= ATMEL_LCDC_DMAEN | ATMEL_LCDC_DMA2DEN,
+	.default_lcdcon2	= (ATMEL_LCDC_DISTYPE_TFT
+				   | ATMEL_LCDC_CLKMOD_ALWAYSACTIVE
+				   | ATMEL_LCDC_INVCLK_NORMAL
+				   | ATMEL_LCDC_MEMOR_BIG),
+	.lcd_wiring_mode	= ATMEL_LCDC_WIRING_RGB,
+	.default_monspecs	= &lcd_fb_default_monspecs,
+	.guard_time		= 2,
+};
+#endif
+
+#ifdef CONFIG_BOARD_MRMT_LCD_KWH043GM08
+/* Sharp KWH043GM08-Fxx (or compatible) panel */
+static struct fb_videomode __initdata lcd_fb_modes[] = {
+	{
+		.name		= "480x272 @ 59.94Hz",
+		.refresh	= 59.94,
+		.xres		= 480,		.yres		= 272,
+		.pixclock	= KHZ2PICOS(9000),
+
+		.left_margin	= 2,		.right_margin	= 2,
+		.upper_margin	= 3,		.lower_margin	= 9,
+		.hsync_len	= 41,		.vsync_len	= 1,
+
+		.sync		= 0,
+		.vmode		= FB_VMODE_NONINTERLACED,
+	},
+};
+
+static struct fb_monspecs __initdata lcd_fb_default_monspecs = {
+	.manufacturer		= "FOR",
+	.monitor		= "KWH043GM08",
+	.modedb			= lcd_fb_modes,
+	.modedb_len		= ARRAY_SIZE(lcd_fb_modes),
+	.hfmin			= 14915,
+	.hfmax			= 17638,
+	.vfmin			= 53,
+	.vfmax			= 61,
+	.dclkmax		= 9260000,
+};
+
+static struct atmel_lcdfb_info __initdata rmt_lcdc_data = {
+	.default_bpp		= 24,
+	.default_dmacon		= ATMEL_LCDC_DMAEN | ATMEL_LCDC_DMA2DEN,
+	.default_lcdcon2	= (ATMEL_LCDC_DISTYPE_TFT
+				   | ATMEL_LCDC_CLKMOD_ALWAYSACTIVE
+				   | ATMEL_LCDC_INVCLK_INVERTED
+				   | ATMEL_LCDC_MEMOR_BIG),
+	.lcd_wiring_mode	= ATMEL_LCDC_WIRING_RGB,
+	.default_monspecs	= &lcd_fb_default_monspecs,
+	.guard_time		= 2,
+};
+#endif
+
+#ifdef CONFIG_BOARD_MRMT_AC97
+static struct ac97c_platform_data __initdata ac97c0_data = {
+	.reset_pin		= PIN_AC97_RST_N,
+};
+#endif
+
+#ifdef CONFIG_BOARD_MRMT_UCB1400_TS
+/* NOTE: IRQ assignment relies on kernel module parameter */
+static struct platform_device rmt_ts_device = {
+	.name	= "ucb1400_ts",
+	.id	= -1,
+	}
+};
+#endif
+
+#ifdef CONFIG_BOARD_MRMT_BL_PWM
+/* PWM LEDs: LCD Backlight, etc */
+static struct gpio_led rmt_pwm_led[] = {
+	/* here the "gpio" is actually a PWM channel */
+	{ .name = "backlight",	.gpio = PWM_CH_BL, },
+};
+
+static struct gpio_led_platform_data rmt_pwm_led_data = {
+	.num_leds	= ARRAY_SIZE(rmt_pwm_led),
+	.leds		= rmt_pwm_led,
+};
+
+static struct platform_device rmt_pwm_led_dev = {
+	.name		= "leds-atmel-pwm",
+	.id		= -1,
+	.dev		= {
+		.platform_data	= &rmt_pwm_led_data,
+	},
+};
+#endif
+
+#ifdef CONFIG_BOARD_MRMT_ADS7846_TS
+static int ads7846_pendown_state(void)
+{
+	return !gpio_get_value( PIN_TS_EXTINT );	/* PENIRQ.*/
+}
+
+static struct ads7846_platform_data ads_info = {
+	.model				= 7846,
+	.keep_vref_on			= 0,	/* Use external VREF pin */
+	.vref_delay_usecs		= 0,
+	.vref_mv			= 3300,	/* VREF = 3.3V */
+	.settle_delay_usecs		= 800,
+	.penirq_recheck_delay_usecs	= 800,
+	.x_plate_ohms			= 750,
+	.y_plate_ohms			= 300,
+	.pressure_max			= 4096,
+	.debounce_max			= 1,
+	.debounce_rep			= 0,
+	.debounce_tol			= (~0),
+	.get_pendown_state		= ads7846_pendown_state,
+	.filter				= NULL,
+	.filter_init			= NULL,
+};
+
+static struct spi_board_info spi01_board_info[] __initdata = {
+	{
+		.modalias	= "ads7846",
+		.max_speed_hz	= 31250*26,
+		.bus_num	= 0,
+		.chip_select	= 1,
+		.platform_data	= &ads_info,
+		.irq		= AT32_EXTINT(TS_IRQ),
+	},
+};
+#endif
+
+/* GPIO Keys: left, right, power, etc */
+static const struct gpio_keys_button rmt_gpio_keys_buttons[] = {
+	[0] = {
+		.type		= EV_KEY,
+		.code		= KEY_POWER,
+		.gpio		= PIN_PWR_SW_N,
+		.active_low	= 1,
+		.desc		= "power button",
+	},
+	[1] = {
+		.type		= EV_KEY,
+		.code		= KEY_LEFT,
+		.gpio		= PIN_PB_LEFT,
+		.active_low	= 1,
+		.desc		= "left button",
+	},
+	[2] = {
+		.type		= EV_KEY,
+		.code		= KEY_RIGHT,
+		.gpio		= PIN_PB_RIGHT,
+		.active_low	= 1,
+		.desc		= "right button",
+	},
+};
+
+static const struct gpio_keys_platform_data rmt_gpio_keys_data = {
+	.nbuttons =	ARRAY_SIZE(rmt_gpio_keys_buttons),
+	.buttons =	(void *) rmt_gpio_keys_buttons,
+};
+
+static struct platform_device rmt_gpio_keys = {
+	.name =		"gpio-keys",
+	.id =		-1,
+	.dev = {
+		.platform_data = (void *) &rmt_gpio_keys_data,
+	}
+};
+
+#ifdef CONFIG_BOARD_MRMT_RTC_I2C
+static struct i2c_board_info __initdata mrmt1_i2c_rtc = {
+	I2C_BOARD_INFO("s35390a", 0x30),
+	.irq		= 0,
+};
+#endif
+
+static void mrmt_power_off(void)
+{
+	/* PWR_ON=0 will force power off */
+	gpio_set_value( PIN_PWR_ON, 0 );
+}
+
+static int __init mrmt1_init(void)
+{
+	gpio_set_value( PIN_PWR_ON, 1 );	/* Ensure PWR_ON is enabled */
+
+	pm_power_off = mrmt_power_off;
+
+	/* Setup USARTS (other than console) */
+	at32_map_usart(2, 1, 0);	/* USART 2: /dev/ttyS1, RMT1:DB9M */
+	at32_map_usart(3, 2, ATMEL_USART_RTS | ATMEL_USART_CTS);
+			/* USART 3: /dev/ttyS2, RMT1:Wireless, w/ RTS/CTS */
+	at32_add_device_usart(1);
+	at32_add_device_usart(2);
+
+	/* Select GPIO Key pins */
+	at32_select_gpio( PIN_PWR_SW_N, AT32_GPIOF_DEGLITCH);
+	at32_select_gpio( PIN_PB_LEFT, AT32_GPIOF_DEGLITCH);
+	at32_select_gpio( PIN_PB_RIGHT, AT32_GPIOF_DEGLITCH);
+	platform_device_register(&rmt_gpio_keys);
+
+#ifdef CONFIG_BOARD_MRMT_RTC_I2C
+	i2c_register_board_info(0, &mrmt1_i2c_rtc, 1);
+#endif
+
+#ifndef CONFIG_BOARD_MRMT_LCD_DISABLE
+	/* User "alternate" LCDC inferface on Port E & D */
+	/* NB: exclude LCDC_CC pin, as NGW100 reserves it for other use */
+	at32_add_device_lcdc(0, &rmt_lcdc_data,
+		fbmem_start, fbmem_size,
+		(ATMEL_LCDC_ALT_24BIT | ATMEL_LCDC_PE_DVAL ) );
+#endif
+
+#ifdef CONFIG_BOARD_MRMT_AC97
+	at32_add_device_ac97c(0, &ac97c0_data, AC97C_BOTH);
+#endif
+
+#ifdef CONFIG_BOARD_MRMT_ADS7846_TS
+	/* Select the Touchscreen interrupt pin mode */
+	at32_select_periph( GPIO_PIOB_BASE, 1 << (PB_EXTINT_BASE+TS_IRQ),
+			GPIO_PERIPH_A, AT32_GPIOF_DEGLITCH);
+	set_irq_type( AT32_EXTINT(TS_IRQ), IRQ_TYPE_EDGE_FALLING );
+	spi_register_board_info(spi01_board_info,ARRAY_SIZE(spi01_board_info));
+#endif
+
+#ifdef CONFIG_BOARD_MRMT_UCB1400_TS
+	/* Select the Touchscreen interrupt pin mode */
+	at32_select_periph( GPIO_PIOB_BASE, 1 << (PB_EXTINT_BASE+TS_IRQ),
+			GPIO_PERIPH_A, AT32_GPIOF_DEGLITCH);
+	platform_device_register(&rmt_ts_device);
+#endif
+
+	at32_select_gpio( PIN_LCD_DISP, AT32_GPIOF_OUTPUT );
+	gpio_request( PIN_LCD_DISP, "LCD_DISP" );
+	gpio_direction_output( PIN_LCD_DISP, 0 );	/* LCD DISP */
+#ifdef CONFIG_BOARD_MRMT_LCD_DISABLE
+	/* Keep Backlight and DISP off */
+	at32_select_gpio( PIN_LCD_BL, AT32_GPIOF_OUTPUT );
+	gpio_request( PIN_LCD_BL, "LCD_BL" );
+	gpio_direction_output( PIN_LCD_BL, 0 );		/* Backlight */
+#else
+	gpio_set_value( PIN_LCD_DISP, 1 );	/* DISP asserted first */
+#ifdef CONFIG_BOARD_MRMT_BL_PWM
+	/* Use PWM for Backlight controls */
+	at32_add_device_pwm(1 << PWM_CH_BL);
+	platform_device_register(&rmt_pwm_led_dev);
+#else
+	/* Backlight always on */
+	udelay( 1 );
+	at32_select_gpio( PIN_LCD_BL, AT32_GPIOF_OUTPUT );
+	gpio_request( PIN_LCD_BL, "LCD_BL" );
+	gpio_direction_output( PIN_LCD_BL, 1 );
+#endif
+#endif
+
+	/* Make sure BT and Zigbee modules in reset */
+	at32_select_gpio( PIN_BT_RST, AT32_GPIOF_OUTPUT );
+	gpio_request( PIN_BT_RST, "BT_RST" );
+	gpio_direction_output( PIN_BT_RST, 1 );
+	/* BT Module in Reset */
+
+	at32_select_gpio( PIN_ZB_RST_N, AT32_GPIOF_OUTPUT );
+	gpio_request( PIN_ZB_RST_N, "ZB_RST_N" );
+	gpio_direction_output( PIN_ZB_RST_N, 0 );
+	/* XBee Module in Reset */
+
+#ifdef CONFIG_BOARD_MRMT_WIRELESS_ZB
+	udelay( 1000 );
+	/* Unreset the XBee Module */
+	gpio_set_value( PIN_ZB_RST_N, 1 );
+#endif
+#ifdef CONFIG_BOARD_MRMT_WIRELESS_BT
+	udelay( 1000 );
+	/* Unreset the BT Module */
+	gpio_set_value( PIN_BT_RST, 0 );
+#endif
+
+	return 0;
+}
+arch_initcall(mrmt1_init);
+
+static int __init mrmt1_early_init(void)
+{
+	/* To maintain power-on signal in case boot loader did not already */
+	at32_select_gpio( PIN_PWR_ON, AT32_GPIOF_OUTPUT );
+	gpio_request( PIN_PWR_ON, "PIN_PWR_ON" );
+	gpio_direction_output( PIN_PWR_ON, 1 );
+
+	return 0;
+}
+core_initcall(mrmt1_early_init);

arch/avr32/boards/atngw100/setup.c

@@ -56,8 +56,13 @@ static struct spi_board_info spi0_board_info[] __initdata = {
 static struct mci_platform_data __initdata mci0_data = {
 	.slot[0] = {
 		.bus_width	= 4,
+#if defined(CONFIG_BOARD_ATNGW100_EVKLCD10X) || defined(CONFIG_BOARD_ATNGW100_MRMT1)
+		.detect_pin     = GPIO_PIN_NONE,
+		.wp_pin         = GPIO_PIN_NONE,
+#else
 		.detect_pin	= GPIO_PIN_PC(25),
 		.wp_pin		= GPIO_PIN_PE(0),
+#endif
 	},
 };
 

arch/avr32/boards/merisc/setup.c

@@ -94,9 +94,10 @@ static struct spi_board_info __initdata spi0_board_info[] = {
 
 static struct mci_platform_data __initdata mci0_data = {
 	.slot[0] = {
-		.bus_width	= 4,
-		.detect_pin	= GPIO_PIN_PE(19),
-		.wp_pin		= GPIO_PIN_PE(20),
+		.bus_width		= 4,
+		.detect_pin		= GPIO_PIN_PE(19),
+		.wp_pin			= GPIO_PIN_PE(20),
+		.detect_is_active_high	= true,
 	},
 };
 

arch/avr32/configs/atngw100_mrmt_defconfig

+#
+# Automatically generated make config: don't edit
+# Linux kernel version: 2.6.30-rc1
+# Wed Jun  3 00:24:53 2009
+#
+CONFIG_AVR32=y
+CONFIG_GENERIC_GPIO=y
+CONFIG_GENERIC_HARDIRQS=y
+CONFIG_STACKTRACE_SUPPORT=y
+CONFIG_LOCKDEP_SUPPORT=y
+CONFIG_TRACE_IRQFLAGS_SUPPORT=y
+CONFIG_HARDIRQS_SW_RESEND=y
+CONFIG_GENERIC_IRQ_PROBE=y
+CONFIG_RWSEM_GENERIC_SPINLOCK=y
+CONFIG_GENERIC_TIME=y
+CONFIG_GENERIC_CLOCKEVENTS=y
+# CONFIG_RWSEM_XCHGADD_ALGORITHM is not set
+# CONFIG_ARCH_HAS_ILOG2_U32 is not set
+# CONFIG_ARCH_HAS_ILOG2_U64 is not set
+CONFIG_GENERIC_HWEIGHT=y
+CONFIG_GENERIC_CALIBRATE_DELAY=y
+CONFIG_GENERIC_BUG=y
+CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+
+#
+# General setup
+#
+CONFIG_EXPERIMENTAL=y
+CONFIG_BROKEN_ON_SMP=y
+CONFIG_INIT_ENV_ARG_LIMIT=32
+CONFIG_LOCALVERSION=""
+# CONFIG_LOCALVERSION_AUTO is not set
+CONFIG_SWAP=y
+CONFIG_SYSVIPC=y
+CONFIG_SYSVIPC_SYSCTL=y
+CONFIG_POSIX_MQUEUE=y
+CONFIG_POSIX_MQUEUE_SYSCTL=y
+CONFIG_BSD_PROCESS_ACCT=y
+CONFIG_BSD_PROCESS_ACCT_V3=y
+# CONFIG_TASKSTATS is not set
+# CONFIG_AUDIT is not set
+
+#
+# RCU Subsystem
+#
+CONFIG_CLASSIC_RCU=y
+# CONFIG_TREE_RCU is not set
+# CONFIG_PREEMPT_RCU is not set
+# CONFIG_TREE_RCU_TRACE is not set
+# CONFIG_PREEMPT_RCU_TRACE is not set
+# CONFIG_IKCONFIG is not set
+CONFIG_LOG_BUF_SHIFT=14
+CONFIG_GROUP_SCHED=y
+CONFIG_FAIR_GROUP_SCHED=y
+# CONFIG_RT_GROUP_SCHED is not set
+CONFIG_USER_SCHED=y
+# CONFIG_CGROUP_SCHED is not set
+# CONFIG_CGROUPS is not set
+CONFIG_SYSFS_DEPRECATED=y
+CONFIG_SYSFS_DEPRECATED_V2=y
+# CONFIG_RELAY is not set
+# CONFIG_NAMESPACES is not set
+CONFIG_BLK_DEV_INITRD=y
+CONFIG_INITRAMFS_SOURCE=""
+CONFIG_RD_GZIP=y
+# CONFIG_RD_BZIP2 is not set
+# CONFIG_RD_LZMA is not set
+CONFIG_CC_OPTIMIZE_FOR_SIZE=y
+CONFIG_SYSCTL=y
+CONFIG_ANON_INODES=y
+CONFIG_EMBEDDED=y
+# CONFIG_SYSCTL_SYSCALL is not set
+CONFIG_KALLSYMS=y
+# CONFIG_KALLSYMS_ALL is not set
+# CONFIG_KALLSYMS_EXTRA_PASS is not set
+CONFIG_HOTPLUG=y
+CONFIG_PRINTK=y
+CONFIG_BUG=y
+CONFIG_ELF_CORE=y
+# CONFIG_BASE_FULL is not set
+CONFIG_FUTEX=y
+CONFIG_EPOLL=y
+CONFIG_SIGNALFD=y
+CONFIG_TIMERFD=y
+CONFIG_EVENTFD=y
+CONFIG_SHMEM=y
+CONFIG_AIO=y
+CONFIG_VM_EVENT_COUNTERS=y
+# CONFIG_SLUB_DEBUG is not set
+CONFIG_COMPAT_BRK=y
+# CONFIG_SLAB is not set
+CONFIG_SLUB=y
+# CONFIG_SLOB is not set
+# CONFIG_PROFILING is not set
+# CONFIG_MARKERS is not set
+CONFIG_HAVE_OPROFILE=y
+# CONFIG_KPROBES is not set
+CONFIG_HAVE_KPROBES=y
+CONFIG_HAVE_CLK=y
+# CONFIG_SLOW_WORK is not set
+# CONFIG_HAVE_GENERIC_DMA_COHERENT is not set
+CONFIG_RT_MUTEXES=y
+CONFIG_BASE_SMALL=1
+CONFIG_MODULES=y
+# CONFIG_MODULE_FORCE_LOAD is not set
+CONFIG_MODULE_UNLOAD=y
+CONFIG_MODULE_FORCE_UNLOAD=y
+# CONFIG_MODVERSIONS is not set
+# CONFIG_MODULE_SRCVERSION_ALL is not set
+CONFIG_BLOCK=y
+# CONFIG_LBD is not set
+# CONFIG_BLK_DEV_BSG is not set
+# CONFIG_BLK_DEV_INTEGRITY is not set
+
+#
+# IO Schedulers
+#
+CONFIG_IOSCHED_NOOP=y
+# CONFIG_IOSCHED_AS is not set
+# CONFIG_IOSCHED_DEADLINE is not set
+CONFIG_IOSCHED_CFQ=y
+# CONFIG_DEFAULT_AS is not set
+# CONFIG_DEFAULT_DEADLINE is not set
+CONFIG_DEFAULT_CFQ=y
+# CONFIG_DEFAULT_NOOP is not set
+CONFIG_DEFAULT_IOSCHED="cfq"
+# CONFIG_FREEZER is not set
+
+#
+# System Type and features
+#
+# CONFIG_NO_HZ is not set
+# CONFIG_HIGH_RES_TIMERS is not set
+CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
+CONFIG_SUBARCH_AVR32B=y
+CONFIG_MMU=y
+CONFIG_PERFORMANCE_COUNTERS=y
+CONFIG_PLATFORM_AT32AP=y
+CONFIG_CPU_AT32AP700X=y
+CONFIG_CPU_AT32AP7000=y
+# CONFIG_BOARD_ATSTK1000 is not set
+CONFIG_BOARD_ATNGW100=y
+# CONFIG_BOARD_HAMMERHEAD is not set
+# CONFIG_BOARD_FAVR_32 is not set
+# CONFIG_BOARD_MERISC is not set
+# CONFIG_BOARD_MIMC200 is not set
+# CONFIG_BOARD_ATNGW100_ADDON_NONE is not set
+# CONFIG_BOARD_ATNGW100_EVKLCD10X is not set
+CONFIG_BOARD_ATNGW100_MRMT=y
+CONFIG_BOARD_MRMT_REV1=y
+# CONFIG_BOARD_MRMT_REV2 is not set
+CONFIG_BOARD_MRMT_AC97=y
+# CONFIG_BOARD_MRMT_UCB1400_TS is not set
+CONFIG_BOARD_MRMT_ADS7846_TS=y
+# CONFIG_BOARD_MRMT_LCD_DISABLE is not set
+CONFIG_BOARD_MRMT_LCD_LQ043T3DX0X=y
+# CONFIG_BOARD_MRMT_LCD_KWH043GM08 is not set
+CONFIG_BOARD_MRMT_BL_PWM=y
+CONFIG_BOARD_MRMT_RTC_I2C=y
+CONFIG_BOARD_MRMT_WIRELESS_ZB=y
+# CONFIG_BOARD_MRMT_WIRELESS_BT is not set
+# CONFIG_BOARD_MRMT_WIRELESS_NONE is not set
+CONFIG_LOADER_U_BOOT=y
+
+#
+# Atmel AVR32 AP options
+#
+# CONFIG_AP700X_32_BIT_SMC is not set
+CONFIG_AP700X_16_BIT_SMC=y
+# CONFIG_AP700X_8_BIT_SMC is not set
+CONFIG_LOAD_ADDRESS=0x10000000
+CONFIG_ENTRY_ADDRESS=0x90000000
+CONFIG_PHYS_OFFSET=0x10000000
+CONFIG_PREEMPT_NONE=y
+# CONFIG_PREEMPT_VOLUNTARY is not set
+# CONFIG_PREEMPT is not set
+CONFIG_QUICKLIST=y
+# CONFIG_HAVE_ARCH_BOOTMEM is not set
+# CONFIG_ARCH_HAVE_MEMORY_PRESENT is not set
+# CONFIG_NEED_NODE_MEMMAP_SIZE is not set
+CONFIG_ARCH_FLATMEM_ENABLE=y
+# CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set
+# CONFIG_ARCH_SPARSEMEM_ENABLE is not set
+CONFIG_SELECT_MEMORY_MODEL=y
+CONFIG_FLATMEM_MANUAL=y
+# CONFIG_DISCONTIGMEM_MANUAL is not set
+# CONFIG_SPARSEMEM_MANUAL is not set
+CONFIG_FLATMEM=y
+CONFIG_FLAT_NODE_MEM_MAP=y
+CONFIG_PAGEFLAGS_EXTENDED=y
+CONFIG_SPLIT_PTLOCK_CPUS=4
+# CONFIG_PHYS_ADDR_T_64BIT is not set
+CONFIG_ZONE_DMA_FLAG=0
+CONFIG_NR_QUICK=2
+CONFIG_VIRT_TO_BUS=y
+CONFIG_UNEVICTABLE_LRU=y
+CONFIG_HAVE_MLOCK=y
+CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+# CONFIG_OWNERSHIP_TRACE is not set
+# CONFIG_NMI_DEBUGGING is not set
+# CONFIG_HZ_100 is not set
+CONFIG_HZ_250=y
+# CONFIG_HZ_300 is not set
+# CONFIG_HZ_1000 is not set
+CONFIG_HZ=250
+# CONFIG_SCHED_HRTICK is not set
+CONFIG_CMDLINE=""
+
+#
+# Power management options
+#
+CONFIG_PM=y
+# CONFIG_PM_DEBUG is not set
+# CONFIG_SUSPEND is not set
+CONFIG_ARCH_SUSPEND_POSSIBLE=y
+
+#
+# CPU Frequency scaling
+#
+CONFIG_CPU_FREQ=y
+CONFIG_CPU_FREQ_TABLE=y
+# CONFIG_CPU_FREQ_DEBUG is not set
+CONFIG_CPU_FREQ_STAT=y
+# CONFIG_CPU_FREQ_STAT_DETAILS is not set
+CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE=y
+# CONFIG_CPU_FREQ_DEFAULT_GOV_POWERSAVE is not set
+# CONFIG_CPU_FREQ_DEFAULT_GOV_USERSPACE is not set
+# CONFIG_CPU_FREQ_DEFAULT_GOV_ONDEMAND is not set
+# CONFIG_CPU_FREQ_DEFAULT_GOV_CONSERVATIVE is not set
+CONFIG_CPU_FREQ_GOV_PERFORMANCE=y
+CONFIG_CPU_FREQ_GOV_POWERSAVE=y
+CONFIG_CPU_FREQ_GOV_USERSPACE=y
+CONFIG_CPU_FREQ_GOV_ONDEMAND=y
+# CONFIG_CPU_FREQ_GOV_CONSERVATIVE is not set
+CONFIG_CPU_FREQ_AT32AP=y
+
+#
+# Bus options
+#
+# CONFIG_ARCH_SUPPORTS_MSI is not set
+# CONFIG_PCCARD is not set
+
+#
+# Executable file formats
+#
+CONFIG_BINFMT_ELF=y
+# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
+# CONFIG_HAVE_AOUT is not set
+# CONFIG_BINFMT_MISC is not set
+CONFIG_NET=y
+
+#
+# Networking options
+#
+CONFIG_PACKET=y
+CONFIG_PACKET_MMAP=y
+CONFIG_UNIX=y
+# CONFIG_NET_KEY is not set
+CONFIG_INET=y
+# CONFIG_IP_MULTICAST is not set
+# CONFIG_IP_ADVANCED_ROUTER is not set
+CONFIG_IP_FIB_HASH=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+# CONFIG_IP_PNP_BOOTP is not set
+# CONFIG_IP_PNP_RARP is not set
+# CONFIG_NET_IPIP is not set
+# CONFIG_NET_IPGRE is not set
+# CONFIG_ARPD is not set
+CONFIG_SYN_COOKIES=y
+# CONFIG_INET_AH is not set
+# CONFIG_INET_ESP is not set
+# CONFIG_INET_IPCOMP is not set
+# CONFIG_INET_XFRM_TUNNEL is not set
+# CONFIG_INET_TUNNEL is not set
+# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
+# CONFIG_INET_XFRM_MODE_TUNNEL is not set
+# CONFIG_INET_XFRM_MODE_BEET is not set
+# CONFIG_INET_LRO is not set
+CONFIG_INET_DIAG=y
+CONFIG_INET_TCP_DIAG=y
+# CONFIG_TCP_CONG_ADVANCED is not set
+CONFIG_TCP_CONG_CUBIC=y
+CONFIG_DEFAULT_TCP_CONG="cubic"
+# CONFIG_TCP_MD5SIG is not set
+# CONFIG_IPV6 is not set
+# CONFIG_NETWORK_SECMARK is not set
+# CONFIG_NETFILTER is not set
+# CONFIG_IP_DCCP is not set
+# CONFIG_IP_SCTP is not set
+# CONFIG_TIPC is not set
+# CONFIG_ATM is not set
+# CONFIG_BRIDGE is not set
+# CONFIG_NET_DSA is not set
+# CONFIG_VLAN_8021Q is not set
+# CONFIG_DECNET is not set
+# CONFIG_LLC2 is not set
+# CONFIG_IPX is not set
+# CONFIG_ATALK is not set
+# CONFIG_X25 is not set
+# CONFIG_LAPB is not set
+# CONFIG_ECONET is not set
+# CONFIG_WAN_ROUTER is not set
+# CONFIG_PHONET is not set
+# CONFIG_NET_SCHED is not set
+# CONFIG_DCB is not set
+
+#
+# Network testing
+#
+# CONFIG_NET_PKTGEN is not set
+# CONFIG_HAMRADIO is not set
+# CONFIG_CAN is not set
+# CONFIG_IRDA is not set
+CONFIG_BT=m
+CONFIG_BT_L2CAP=m
+# CONFIG_BT_SCO is not set
+CONFIG_BT_RFCOMM=m
+CONFIG_BT_RFCOMM_TTY=y
+# CONFIG_BT_BNEP is not set
+CONFIG_BT_HIDP=m
+
+#
+# Bluetooth device drivers
+#
+# CONFIG_BT_HCIBTSDIO is not set
+CONFIG_BT_HCIUART=m
+CONFIG_BT_HCIUART_H4=y
+CONFIG_BT_HCIUART_BCSP=y
+# CONFIG_BT_HCIUART_LL is not set
+# CONFIG_BT_HCIVHCI is not set
+# CONFIG_AF_RXRPC is not set
+# CONFIG_WIRELESS is not set
+# CONFIG_WIMAX is not set
+# CONFIG_RFKILL is not set
+# CONFIG_NET_9P is not set
+
+#
+# Device Drivers
+#
+
+#
+# Generic Driver Options
+#
+CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+CONFIG_STANDALONE=y
+# CONFIG_PREVENT_FIRMWARE_BUILD is not set
+# CONFIG_FW_LOADER is not set
+# CONFIG_DEBUG_DRIVER is not set
+# CONFIG_DEBUG_DEVRES is not set
+# CONFIG_SYS_HYPERVISOR is not set
+# CONFIG_CONNECTOR is not set
+CONFIG_MTD=y
+# CONFIG_MTD_DEBUG is not set
+# CONFIG_MTD_CONCAT is not set
+CONFIG_MTD_PARTITIONS=y
+# CONFIG_MTD_TESTS is not set
+# CONFIG_MTD_REDBOOT_PARTS is not set
+CONFIG_MTD_CMDLINE_PARTS=y
+# CONFIG_MTD_AR7_PARTS is not set
+
+#
+# User Modules And Translation Layers
+#
+CONFIG_MTD_CHAR=y
+CONFIG_MTD_BLKDEVS=y
+CONFIG_MTD_BLOCK=y
+# CONFIG_FTL is not set
+# CONFIG_NFTL is not set
+# CONFIG_INFTL is not set
+# CONFIG_RFD_FTL is not set
+# CONFIG_SSFDC is not set
+# CONFIG_MTD_OOPS is not set
+
+#
+# RAM/ROM/Flash chip drivers
+#
+CONFIG_MTD_CFI=y
+# CONFIG_MTD_JEDECPROBE is not set
+CONFIG_MTD_GEN_PROBE=y
+# CONFIG_MTD_CFI_ADV_OPTIONS is not set
+CONFIG_MTD_MAP_BANK_WIDTH_1=y
+CONFIG_MTD_MAP_BANK_WIDTH_2=y
+CONFIG_MTD_MAP_BANK_WIDTH_4=y
+# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set
+CONFIG_MTD_CFI_I1=y
+CONFIG_MTD_CFI_I2=y
+# CONFIG_MTD_CFI_I4 is not set
+# CONFIG_MTD_CFI_I8 is not set
+# CONFIG_MTD_CFI_INTELEXT is not set
+CONFIG_MTD_CFI_AMDSTD=y
+# CONFIG_MTD_CFI_STAA is not set
+CONFIG_MTD_CFI_UTIL=y
+# CONFIG_MTD_RAM is not set
+# CONFIG_MTD_ROM is not set
+# CONFIG_MTD_ABSENT is not set
+
+#
+# Mapping drivers for chip access
+#
+# CONFIG_MTD_COMPLEX_MAPPINGS is not set
+CONFIG_MTD_PHYSMAP=y
+# CONFIG_MTD_PHYSMAP_COMPAT is not set
+# CONFIG_MTD_PLATRAM is not set
+
+#
+# Self-contained MTD device drivers
+#
+CONFIG_MTD_DATAFLASH=y
+# CONFIG_MTD_DATAFLASH_WRITE_VERIFY is not set
+# CONFIG_MTD_DATAFLASH_OTP is not set
+# CONFIG_MTD_M25P80 is not set
+# CONFIG_MTD_SLRAM is not set
+# CONFIG_MTD_PHRAM is not set
+# CONFIG_MTD_MTDRAM is not set
+# CONFIG_MTD_BLOCK2MTD is not set
+
+#
+# Disk-On-Chip Device Drivers
+#
+# CONFIG_MTD_DOC2000 is not set
+# CONFIG_MTD_DOC2001 is not set
+# CONFIG_MTD_DOC2001PLUS is not set
+# CONFIG_MTD_NAND is not set
+# CONFIG_MTD_ONENAND is not set
+
+#
+# LPDDR flash memory drivers
+#
+# CONFIG_MTD_LPDDR is not set
+
+#
+# UBI - Unsorted block images
+#
+# CONFIG_MTD_UBI is not set
+# CONFIG_PARPORT is not set
+CONFIG_BLK_DEV=y
+# CONFIG_BLK_DEV_COW_COMMON is not set
+CONFIG_BLK_DEV_LOOP=y
+# CONFIG_BLK_DEV_CRYPTOLOOP is not set
+# CONFIG_BLK_DEV_NBD is not set
+# CONFIG_BLK_DEV_RAM is not set
+# CONFIG_CDROM_PKTCDVD is not set
+# CONFIG_ATA_OVER_ETH is not set
+CONFIG_MISC_DEVICES=y
+CONFIG_ATMEL_PWM=y
+# CONFIG_ATMEL_TCLIB is not set
+# CONFIG_ICS932S401 is not set
+# CONFIG_ATMEL_SSC is not set
+# CONFIG_ENCLOSURE_SERVICES is not set
+# CONFIG_ISL29003 is not set
+# CONFIG_C2PORT is not set
+
+#
+# EEPROM support
+#
+# CONFIG_EEPROM_AT24 is not set
+# CONFIG_EEPROM_AT25 is not set
+# CONFIG_EEPROM_LEGACY is not set
+# CONFIG_EEPROM_93CX6 is not set
+
+#
+# SCSI device support
+#
+# CONFIG_RAID_ATTRS is not set
+# CONFIG_SCSI is not set
+# CONFIG_SCSI_DMA is not set
+# CONFIG_SCSI_NETLINK is not set
+# CONFIG_ATA is not set
+# CONFIG_MD is not set
+CONFIG_NETDEVICES=y
+CONFIG_COMPAT_NET_DEV_OPS=y
+# CONFIG_DUMMY is not set
+# CONFIG_BONDING is not set
+# CONFIG_MACVLAN is not set
+# CONFIG_EQUALIZER is not set
+# CONFIG_TUN is not set
+# CONFIG_VETH is not set
+CONFIG_PHYLIB=y
+
+#
+# MII PHY device drivers
+#
+# CONFIG_MARVELL_PHY is not set
+# CONFIG_DAVICOM_PHY is not set
+# CONFIG_QSEMI_PHY is not set
+# CONFIG_LXT_PHY is not set
+# CONFIG_CICADA_PHY is not set
+# CONFIG_VITESSE_PHY is not set
+# CONFIG_SMSC_PHY is not set
+# CONFIG_BROADCOM_PHY is not set
+# CONFIG_ICPLUS_PHY is not set
+# CONFIG_REALTEK_PHY is not set
+# CONFIG_NATIONAL_PHY is not set
+# CONFIG_STE10XP is not set
+# CONFIG_LSI_ET1011C_PHY is not set
+# CONFIG_FIXED_PHY is not set
+# CONFIG_MDIO_BITBANG is not set
+CONFIG_NET_ETHERNET=y
+# CONFIG_MII is not set
+CONFIG_MACB=y
+# CONFIG_ENC28J60 is not set
+# CONFIG_ETHOC is not set
+# CONFIG_DNET is not set
+# CONFIG_IBM_NEW_EMAC_ZMII is not set
+# CONFIG_IBM_NEW_EMAC_RGMII is not set
+# CONFIG_IBM_NEW_EMAC_TAH is not set
+# CONFIG_IBM_NEW_EMAC_EMAC4 is not set
+# CONFIG_IBM_NEW_EMAC_NO_FLOW_CTRL is not set
+# CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set
+# CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set
+# CONFIG_B44 is not set
+# CONFIG_NETDEV_1000 is not set
+# CONFIG_NETDEV_10000 is not set
+
+#
+# Wireless LAN
+#
+# CONFIG_WLAN_PRE80211 is not set
+# CONFIG_WLAN_80211 is not set
+
+#
+# Enable WiMAX (Networking options) to see the WiMAX drivers
+#
+# CONFIG_WAN is not set
+# CONFIG_PPP is not set
+# CONFIG_SLIP is not set
+# CONFIG_NETCONSOLE is not set
+# CONFIG_NETPOLL is not set
+# CONFIG_NET_POLL_CONTROLLER is not set
+# CONFIG_ISDN is not set
+# CONFIG_PHONE is not set
+
+#
+# Input device support
+#
+CONFIG_INPUT=y
+# CONFIG_INPUT_FF_MEMLESS is not set
+# CONFIG_INPUT_POLLDEV is not set
+
+#
+# Userland interfaces
+#
+# CONFIG_INPUT_MOUSEDEV is not set
+# CONFIG_INPUT_JOYDEV is not set
+CONFIG_INPUT_EVDEV=y
+# CONFIG_INPUT_EVBUG is not set
+
+#
+# Input Device Drivers
+#
+CONFIG_INPUT_KEYBOARD=y
+# CONFIG_KEYBOARD_ATKBD is not set
+# CONFIG_KEYBOARD_SUNKBD is not set
+# CONFIG_KEYBOARD_LKKBD is not set
+# CONFIG_KEYBOARD_XTKBD is not set
+# CONFIG_KEYBOARD_NEWTON is not set
+# CONFIG_KEYBOARD_STOWAWAY is not set
+CONFIG_KEYBOARD_GPIO=y
+# CONFIG_INPUT_MOUSE is not set
+# CONFIG_INPUT_JOYSTICK is not set
+# CONFIG_INPUT_TABLET is not set
+CONFIG_INPUT_TOUCHSCREEN=y
+CONFIG_TOUCHSCREEN_ADS7846=m
+# CONFIG_TOUCHSCREEN_FUJITSU is not set
+# CONFIG_TOUCHSCREEN_GUNZE is not set
+# CONFIG_TOUCHSCREEN_ELO is not set
+# CONFIG_TOUCHSCREEN_WACOM_W8001 is not set
+# CONFIG_TOUCHSCREEN_MTOUCH is not set
+# CONFIG_TOUCHSCREEN_INEXIO is not set
+# CONFIG_TOUCHSCREEN_MK712 is not set
+# CONFIG_TOUCHSCREEN_PENMOUNT is not set
+# CONFIG_TOUCHSCREEN_TOUCHRIGHT is not set
+# CONFIG_TOUCHSCREEN_TOUCHWIN is not set
+# CONFIG_TOUCHSCREEN_WM97XX is not set
+# CONFIG_TOUCHSCREEN_TOUCHIT213 is not set
+# CONFIG_TOUCHSCREEN_TSC2007 is not set
+# CONFIG_INPUT_MISC is not set
+
+#
+# Hardware I/O ports
+#
+# CONFIG_SERIO is not set
+# CONFIG_GAMEPORT is not set
+
+#
+# Character devices
+#
+CONFIG_VT=y
+CONFIG_CONSOLE_TRANSLATIONS=y
+CONFIG_VT_CONSOLE=y
+CONFIG_HW_CONSOLE=y
+CONFIG_VT_HW_CONSOLE_BINDING=y
+CONFIG_DEVKMEM=y
+# CONFIG_SERIAL_NONSTANDARD is not set
+
+#
+# Serial drivers
+#
+# CONFIG_SERIAL_8250 is not set
+
+#
+# Non-8250 serial port support
+#
+CONFIG_SERIAL_ATMEL=y
+CONFIG_SERIAL_ATMEL_CONSOLE=y
+CONFIG_SERIAL_ATMEL_PDC=y
+# CONFIG_SERIAL_ATMEL_TTYAT is not set
+# CONFIG_SERIAL_MAX3100 is not set
+CONFIG_SERIAL_CORE=y
+CONFIG_SERIAL_CORE_CONSOLE=y
+CONFIG_UNIX98_PTYS=y
+# CONFIG_DEVPTS_MULTIPLE_INSTANCES is not set
+# CONFIG_LEGACY_PTYS is not set
+# CONFIG_IPMI_HANDLER is not set
+# CONFIG_HW_RANDOM is not set
+# CONFIG_R3964 is not set
+# CONFIG_RAW_DRIVER is not set
+# CONFIG_TCG_TPM is not set
+CONFIG_I2C=y
+CONFIG_I2C_BOARDINFO=y
+CONFIG_I2C_CHARDEV=y
+CONFIG_I2C_HELPER_AUTO=y
+CONFIG_I2C_ALGOBIT=y
+
+#
+# I2C Hardware Bus support
+#
+
+#
+# I2C system bus drivers (mostly embedded / system-on-chip)
+#
+CONFIG_I2C_GPIO=y
+# CONFIG_I2C_OCORES is not set
+# CONFIG_I2C_SIMTEC is not set
+
+#
+# External I2C/SMBus adapter drivers
+#
+# CONFIG_I2C_PARPORT_LIGHT is not set
+# CONFIG_I2C_TAOS_EVM is not set
+
+#
+# Other I2C/SMBus bus drivers
+#
+# CONFIG_I2C_PCA_PLATFORM is not set
+# CONFIG_I2C_STUB is not set
+
+#
+# Miscellaneous I2C Chip support
+#
+# CONFIG_DS1682 is not set
+# CONFIG_SENSORS_PCF8574 is not set
+# CONFIG_PCF8575 is not set
+# CONFIG_SENSORS_PCA9539 is not set
+# CONFIG_SENSORS_MAX6875 is not set
+# CONFIG_SENSORS_TSL2550 is not set
+# CONFIG_I2C_DEBUG_CORE is not set
+# CONFIG_I2C_DEBUG_ALGO is not set
+# CONFIG_I2C_DEBUG_BUS is not set
+# CONFIG_I2C_DEBUG_CHIP is not set
+CONFIG_SPI=y
+# CONFIG_SPI_DEBUG is not set
+CONFIG_SPI_MASTER=y
+
+#
+# SPI Master Controller Drivers
+#
+CONFIG_SPI_ATMEL=y
+# CONFIG_SPI_BITBANG is not set
+# CONFIG_SPI_GPIO is not set
+
+#
+# SPI Protocol Masters
+#
+CONFIG_SPI_SPIDEV=y
+# CONFIG_SPI_TLE62X0 is not set
+CONFIG_ARCH_REQUIRE_GPIOLIB=y
+CONFIG_GPIOLIB=y
+# CONFIG_DEBUG_GPIO is not set
+# CONFIG_GPIO_SYSFS is not set
+
+#
+# Memory mapped GPIO expanders:
+#
+
+#
+# I2C GPIO expanders:
+#
+# CONFIG_GPIO_MAX732X is not set
+# CONFIG_GPIO_PCA953X is not set
+# CONFIG_GPIO_PCF857X is not set
+
+#
+# PCI GPIO expanders:
+#
+
+#
+# SPI GPIO expanders:
+#
+# CONFIG_GPIO_MAX7301 is not set
+# CONFIG_GPIO_MCP23S08 is not set
+# CONFIG_W1 is not set
+# CONFIG_POWER_SUPPLY is not set
+CONFIG_HWMON=y
+# CONFIG_HWMON_VID is not set
+# CONFIG_SENSORS_AD7414 is not set
+# CONFIG_SENSORS_AD7418 is not set
+# CONFIG_SENSORS_ADCXX is not set
+# CONFIG_SENSORS_ADM1021 is not set
+# CONFIG_SENSORS_ADM1025 is not set
+# CONFIG_SENSORS_ADM1026 is not set
+# CONFIG_SENSORS_ADM1029 is not set
+# CONFIG_SENSORS_ADM1031 is not set
+# CONFIG_SENSORS_ADM9240 is not set
+# CONFIG_SENSORS_ADT7462 is not set
+# CONFIG_SENSORS_ADT7470 is not set
+# CONFIG_SENSORS_ADT7473 is not set
+# CONFIG_SENSORS_ADT7475 is not set
+# CONFIG_SENSORS_ATXP1 is not set
+# CONFIG_SENSORS_DS1621 is not set
+# CONFIG_SENSORS_F71805F is not set
+# CONFIG_SENSORS_F71882FG is not set
+# CONFIG_SENSORS_F75375S is not set
+# CONFIG_SENSORS_G760A is not set
+# CONFIG_SENSORS_GL518SM is not set
+# CONFIG_SENSORS_GL520SM is not set
+# CONFIG_SENSORS_IT87 is not set
+# CONFIG_SENSORS_LM63 is not set
+# CONFIG_SENSORS_LM70 is not set
+# CONFIG_SENSORS_LM75 is not set
+# CONFIG_SENSORS_LM77 is not set
+# CONFIG_SENSORS_LM78 is not set
+# CONFIG_SENSORS_LM80 is not set
+# CONFIG_SENSORS_LM83 is not set
+# CONFIG_SENSORS_LM85 is not set
+# CONFIG_SENSORS_LM87 is not set
+# CONFIG_SENSORS_LM90 is not set
+# CONFIG_SENSORS_LM92 is not set
+# CONFIG_SENSORS_LM93 is not set
+# CONFIG_SENSORS_LTC4215 is not set
+# CONFIG_SENSORS_LTC4245 is not set
+# CONFIG_SENSORS_LM95241 is not set
+# CONFIG_SENSORS_MAX1111 is not set
+# CONFIG_SENSORS_MAX1619 is not set
+# CONFIG_SENSORS_MAX6650 is not set
+# CONFIG_SENSORS_PC87360 is not set
+# CONFIG_SENSORS_PC87427 is not set
+# CONFIG_SENSORS_PCF8591 is not set
+# CONFIG_SENSORS_DME1737 is not set
+# CONFIG_SENSORS_SMSC47M1 is not set
+# CONFIG_SENSORS_SMSC47M192 is not set
+# CONFIG_SENSORS_SMSC47B397 is not set
+# CONFIG_SENSORS_ADS7828 is not set
+# CONFIG_SENSORS_THMC50 is not set
+# CONFIG_SENSORS_VT1211 is not set
+# CONFIG_SENSORS_W83781D is not set
+# CONFIG_SENSORS_W83791D is not set
+# CONFIG_SENSORS_W83792D is not set
+# CONFIG_SENSORS_W83793 is not set
+# CONFIG_SENSORS_W83L785TS is not set
+# CONFIG_SENSORS_W83L786NG is not set
+# CONFIG_SENSORS_W83627HF is not set
+# CONFIG_SENSORS_W83627EHF is not set
+# CONFIG_SENSORS_LIS3_SPI is not set
+# CONFIG_HWMON_DEBUG_CHIP is not set
+# CONFIG_THERMAL is not set
+# CONFIG_THERMAL_HWMON is not set
+CONFIG_WATCHDOG=y
+# CONFIG_WATCHDOG_NOWAYOUT is not set
+
+#
+# Watchdog Device Drivers
+#
+# CONFIG_SOFT_WATCHDOG is not set
+CONFIG_AT32AP700X_WDT=y
+CONFIG_SSB_POSSIBLE=y
+
+#
+# Sonics Silicon Backplane
+#
+# CONFIG_SSB is not set
+
+#
+# Multifunction device drivers
+#
+# CONFIG_MFD_CORE is not set
+# CONFIG_MFD_SM501 is not set
+# CONFIG_HTC_PASIC3 is not set
+# CONFIG_UCB1400_CORE is not set
+# CONFIG_TPS65010 is not set
+# CONFIG_TWL4030_CORE is not set
+# CONFIG_MFD_TMIO is not set
+# CONFIG_PMIC_DA903X is not set
+# CONFIG_MFD_WM8400 is not set
+# CONFIG_MFD_WM8350_I2C is not set
+# CONFIG_MFD_PCF50633 is not set
+# CONFIG_REGULATOR is not set
+
+#
+# Multimedia devices
+#
+
+#
+# Multimedia core support
+#
+# CONFIG_VIDEO_DEV is not set
+# CONFIG_DVB_CORE is not set
+# CONFIG_VIDEO_MEDIA is not set
+
+#
+# Multimedia drivers
+#
+# CONFIG_DAB is not set
+
+#
+# Graphics support
+#
+# CONFIG_VGASTATE is not set
+# CONFIG_VIDEO_OUTPUT_CONTROL is not set
+CONFIG_FB=y
+# CONFIG_FIRMWARE_EDID is not set
+# CONFIG_FB_DDC is not set
+# CONFIG_FB_BOOT_VESA_SUPPORT is not set
+CONFIG_FB_CFB_FILLRECT=y
+CONFIG_FB_CFB_COPYAREA=y
+CONFIG_FB_CFB_IMAGEBLIT=y
+# CONFIG_FB_CFB_REV_PIXELS_IN_BYTE is not set
+# CONFIG_FB_SYS_FILLRECT is not set
+# CONFIG_FB_SYS_COPYAREA is not set
+# CONFIG_FB_SYS_IMAGEBLIT is not set
+# CONFIG_FB_FOREIGN_ENDIAN is not set
+# CONFIG_FB_SYS_FOPS is not set
+# CONFIG_FB_SVGALIB is not set
+# CONFIG_FB_MACMODES is not set
+# CONFIG_FB_BACKLIGHT is not set
+# CONFIG_FB_MODE_HELPERS is not set
+# CONFIG_FB_TILEBLITTING is not set
+
+#
+# Frame buffer hardware drivers
+#
+# CONFIG_FB_S1D13XXX is not set
+CONFIG_FB_ATMEL=y
+# CONFIG_FB_VIRTUAL is not set
+# CONFIG_FB_METRONOME is not set
+# CONFIG_FB_MB862XX is not set
+# CONFIG_FB_BROADSHEET is not set
+CONFIG_BACKLIGHT_LCD_SUPPORT=y
+CONFIG_LCD_CLASS_DEVICE=y
+# CONFIG_LCD_LTV350QV is not set
+# CONFIG_LCD_ILI9320 is not set
+# CONFIG_LCD_TDO24M is not set
+# CONFIG_LCD_VGG2432A4 is not set
+# CONFIG_LCD_PLATFORM is not set
+CONFIG_BACKLIGHT_CLASS_DEVICE=y
+# CONFIG_BACKLIGHT_ATMEL_LCDC is not set
+# CONFIG_BACKLIGHT_ATMEL_PWM is not set
+CONFIG_BACKLIGHT_GENERIC=y
+
+#
+# Display device support
+#
+# CONFIG_DISPLAY_SUPPORT is not set
+
+#
+# Console display driver support
+#
+CONFIG_DUMMY_CONSOLE=y
+# CONFIG_FRAMEBUFFER_CONSOLE is not set
+# CONFIG_LOGO is not set
+CONFIG_SOUND=m
+CONFIG_SOUND_OSS_CORE=y
+CONFIG_SND=m
+CONFIG_SND_TIMER=m
+CONFIG_SND_PCM=m
+# CONFIG_SND_SEQUENCER is not set
+CONFIG_SND_OSSEMUL=y
+CONFIG_SND_MIXER_OSS=m
+CONFIG_SND_PCM_OSS=m
+CONFIG_SND_PCM_OSS_PLUGINS=y
+# CONFIG_SND_DYNAMIC_MINORS is not set
+# CONFIG_SND_SUPPORT_OLD_API is not set
+# CONFIG_SND_VERBOSE_PROCFS is not set
+# CONFIG_SND_VERBOSE_PRINTK is not set
+# CONFIG_SND_DEBUG is not set
+CONFIG_SND_VMASTER=y
+CONFIG_SND_AC97_CODEC=m
+CONFIG_SND_DRIVERS=y
+# CONFIG_SND_DUMMY is not set
+# CONFIG_SND_MTPAV is not set
+# CONFIG_SND_SERIAL_U16550 is not set
+# CONFIG_SND_MPU401 is not set
+# CONFIG_SND_AC97_POWER_SAVE is not set
+
+#
+# Atmel devices (AVR32 and AT91)
+#
+# CONFIG_SND_ATMEL_ABDAC is not set
+CONFIG_SND_ATMEL_AC97C=m
+# CONFIG_SND_SPI is not set
+# CONFIG_SND_SOC is not set
+# CONFIG_SOUND_PRIME is not set
+CONFIG_AC97_BUS=m
+CONFIG_HID_SUPPORT=y
+CONFIG_HID=y
+# CONFIG_HID_DEBUG is not set
+# CONFIG_HIDRAW is not set
+# CONFIG_HID_PID is not set
+
+#
+# Special HID drivers
+#
+# CONFIG_HID_APPLE is not set
+CONFIG_USB_SUPPORT=y
+# CONFIG_USB_ARCH_HAS_HCD is not set
+# CONFIG_USB_ARCH_HAS_OHCI is not set
+# CONFIG_USB_ARCH_HAS_EHCI is not set
+# CONFIG_USB_OTG_WHITELIST is not set
+# CONFIG_USB_OTG_BLACKLIST_HUB is not set
+# CONFIG_USB_MUSB_HDRC is not set
+# CONFIG_USB_GADGET_MUSB_HDRC is not set
+
+#
+# NOTE: USB_STORAGE depends on SCSI but BLK_DEV_SD may
+#
+CONFIG_USB_GADGET=m
+# CONFIG_USB_GADGET_DEBUG is not set
+CONFIG_USB_GADGET_DEBUG_FILES=y
+# CONFIG_USB_GADGET_DEBUG_FS is not set
+CONFIG_USB_GADGET_VBUS_DRAW=2
+CONFIG_USB_GADGET_SELECTED=y
+# CONFIG_USB_GADGET_AT91 is not set
+CONFIG_USB_GADGET_ATMEL_USBA=y
+CONFIG_USB_ATMEL_USBA=m
+# CONFIG_USB_GADGET_FSL_USB2 is not set
+# CONFIG_USB_GADGET_LH7A40X is not set
+# CONFIG_USB_GADGET_OMAP is not set
+# CONFIG_USB_GADGET_PXA25X is not set
+# CONFIG_USB_GADGET_PXA27X is not set
+# CONFIG_USB_GADGET_S3C2410 is not set
+# CONFIG_USB_GADGET_IMX is not set
+# CONFIG_USB_GADGET_M66592 is not set
+# CONFIG_USB_GADGET_AMD5536UDC is not set
+# CONFIG_USB_GADGET_FSL_QE is not set
+# CONFIG_USB_GADGET_CI13XXX is not set
+# CONFIG_USB_GADGET_NET2280 is not set
+# CONFIG_USB_GADGET_GOKU is not set
+# CONFIG_USB_GADGET_DUMMY_HCD is not set
+CONFIG_USB_GADGET_DUALSPEED=y
+# CONFIG_USB_ZERO is not set
+# CONFIG_USB_ETH is not set
+# CONFIG_USB_GADGETFS is not set
+CONFIG_USB_FILE_STORAGE=m
+# CONFIG_USB_FILE_STORAGE_TEST is not set
+CONFIG_USB_G_SERIAL=m
+# CONFIG_USB_MIDI_GADGET is not set
+# CONFIG_USB_G_PRINTER is not set
+# CONFIG_USB_CDC_COMPOSITE is not set
+
+#
+# OTG and related infrastructure
+#
+# CONFIG_USB_GPIO_VBUS is not set
+# CONFIG_NOP_USB_XCEIV is not set
+CONFIG_MMC=y
+# CONFIG_MMC_DEBUG is not set
+# CONFIG_MMC_UNSAFE_RESUME is not set
+
+#
+# MMC/SD/SDIO Card Drivers
+#
+CONFIG_MMC_BLOCK=y
+CONFIG_MMC_BLOCK_BOUNCE=y
+# CONFIG_SDIO_UART is not set
+# CONFIG_MMC_TEST is not set
+
+#
+# MMC/SD/SDIO Host Controller Drivers
+#
+# CONFIG_MMC_SDHCI is not set
+CONFIG_MMC_ATMELMCI=y
+# CONFIG_MMC_ATMELMCI_DMA is not set
+# CONFIG_MMC_SPI is not set
+# CONFIG_MEMSTICK is not set
+CONFIG_NEW_LEDS=y
+CONFIG_LEDS_CLASS=y
+
+#
+# LED drivers
+#
+CONFIG_LEDS_ATMEL_PWM=y
+# CONFIG_LEDS_PCA9532 is not set
+CONFIG_LEDS_GPIO=y
+CONFIG_LEDS_GPIO_PLATFORM=y
+# CONFIG_LEDS_LP5521 is not set
+# CONFIG_LEDS_PCA955X is not set
+# CONFIG_LEDS_DAC124S085 is not set
+# CONFIG_LEDS_BD2802 is not set
+
+#
+# LED Triggers
+#
+CONFIG_LEDS_TRIGGERS=y
+CONFIG_LEDS_TRIGGER_TIMER=y
+CONFIG_LEDS_TRIGGER_HEARTBEAT=y
+# CONFIG_LEDS_TRIGGER_BACKLIGHT is not set
+# CONFIG_LEDS_TRIGGER_GPIO is not set
+# CONFIG_LEDS_TRIGGER_DEFAULT_ON is not set
+
+#
+# iptables trigger is under Netfilter config (LED target)
+#
+# CONFIG_ACCESSIBILITY is not set
+CONFIG_RTC_LIB=m
+CONFIG_RTC_CLASS=m
+
+#
+# RTC interfaces
+#
+CONFIG_RTC_INTF_SYSFS=y
+CONFIG_RTC_INTF_PROC=y
+CONFIG_RTC_INTF_DEV=y
+# CONFIG_RTC_INTF_DEV_UIE_EMUL is not set
+# CONFIG_RTC_DRV_TEST is not set
+
+#
+# I2C RTC drivers
+#
+# CONFIG_RTC_DRV_DS1307 is not set
+# CONFIG_RTC_DRV_DS1374 is not set
+# CONFIG_RTC_DRV_DS1672 is not set
+# CONFIG_RTC_DRV_MAX6900 is not set
+# CONFIG_RTC_DRV_RS5C372 is not set
+# CONFIG_RTC_DRV_ISL1208 is not set
+# CONFIG_RTC_DRV_X1205 is not set
+# CONFIG_RTC_DRV_PCF8563 is not set
+# CONFIG_RTC_DRV_PCF8583 is not set
+# CONFIG_RTC_DRV_M41T80 is not set
+CONFIG_RTC_DRV_S35390A=m
+# CONFIG_RTC_DRV_FM3130 is not set
+# CONFIG_RTC_DRV_RX8581 is not set
+
+#
+# SPI RTC drivers
+#
+# CONFIG_RTC_DRV_M41T94 is not set
+# CONFIG_RTC_DRV_DS1305 is not set
+# CONFIG_RTC_DRV_DS1390 is not set
+# CONFIG_RTC_DRV_MAX6902 is not set
+# CONFIG_RTC_DRV_R9701 is not set
+# CONFIG_RTC_DRV_RS5C348 is not set
+# CONFIG_RTC_DRV_DS3234 is not set
+
+#
+# Platform RTC drivers
+#
+# CONFIG_RTC_DRV_DS1286 is not set
+# CONFIG_RTC_DRV_DS1511 is not set
+# CONFIG_RTC_DRV_DS1553 is not set
+# CONFIG_RTC_DRV_DS1742 is not set
+# CONFIG_RTC_DRV_STK17TA8 is not set
+# CONFIG_RTC_DRV_M48T86 is not set
+# CONFIG_RTC_DRV_M48T35 is not set
+# CONFIG_RTC_DRV_M48T59 is not set
+# CONFIG_RTC_DRV_BQ4802 is not set
+# CONFIG_RTC_DRV_V3020 is not set
+
+#
+# on-CPU RTC drivers
+#
+CONFIG_RTC_DRV_AT32AP700X=m
+CONFIG_DMADEVICES=y
+
+#
+# DMA Devices
+#
+CONFIG_DW_DMAC=y
+CONFIG_DMA_ENGINE=y
+
+#
+# DMA Clients
+#
+# CONFIG_NET_DMA is not set
+# CONFIG_ASYNC_TX_DMA is not set
+# CONFIG_DMATEST is not set
+# CONFIG_AUXDISPLAY is not set
+CONFIG_UIO=y
+# CONFIG_UIO_PDRV is not set
+# CONFIG_UIO_PDRV_GENIRQ is not set
+# CONFIG_UIO_SMX is not set
+# CONFIG_UIO_SERCOS3 is not set
+# CONFIG_STAGING is not set
+
+#
+# File systems
+#
+CONFIG_EXT2_FS=y
+CONFIG_EXT2_FS_XATTR=y
+# CONFIG_EXT2_FS_POSIX_ACL is not set
+# CONFIG_EXT2_FS_SECURITY is not set
+# CONFIG_EXT2_FS_XIP is not set
+CONFIG_EXT3_FS=y
+# CONFIG_EXT3_DEFAULTS_TO_ORDERED is not set
+CONFIG_EXT3_FS_XATTR=y
+# CONFIG_EXT3_FS_POSIX_ACL is not set
+# CONFIG_EXT3_FS_SECURITY is not set
+# CONFIG_EXT4_FS is not set
+CONFIG_JBD=y
+# CONFIG_JBD_DEBUG is not set
+CONFIG_FS_MBCACHE=y
+# CONFIG_REISERFS_FS is not set
+# CONFIG_JFS_FS is not set
+# CONFIG_FS_POSIX_ACL is not set
+CONFIG_FILE_LOCKING=y
+# CONFIG_XFS_FS is not set
+# CONFIG_OCFS2_FS is not set
+# CONFIG_BTRFS_FS is not set
+# CONFIG_DNOTIFY is not set
+# CONFIG_INOTIFY is not set
+# CONFIG_QUOTA is not set
+# CONFIG_AUTOFS_FS is not set
+# CONFIG_AUTOFS4_FS is not set
+# CONFIG_FUSE_FS is not set
+
+#
+# Caches
+#
+# CONFIG_FSCACHE is not set
+
+#
+# CD-ROM/DVD Filesystems
+#
+# CONFIG_ISO9660_FS is not set
+# CONFIG_UDF_FS is not set
+
+#
+# DOS/FAT/NT Filesystems
+#
+CONFIG_FAT_FS=y
+CONFIG_MSDOS_FS=y
+CONFIG_VFAT_FS=y
+CONFIG_FAT_DEFAULT_CODEPAGE=850
+CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1"
+CONFIG_NTFS_FS=m
+# CONFIG_NTFS_DEBUG is not set
+CONFIG_NTFS_RW=y
+
+#
+# Pseudo filesystems
+#
+CONFIG_PROC_FS=y
+# CONFIG_PROC_KCORE is not set
+CONFIG_PROC_SYSCTL=y
+CONFIG_PROC_PAGE_MONITOR=y
+CONFIG_SYSFS=y
+CONFIG_TMPFS=y
+# CONFIG_TMPFS_POSIX_ACL is not set
+# CONFIG_HUGETLB_PAGE is not set
+CONFIG_CONFIGFS_FS=y
+CONFIG_MISC_FILESYSTEMS=y
+# CONFIG_ADFS_FS is not set
+# CONFIG_AFFS_FS is not set
+# CONFIG_HFS_FS is not set
+# CONFIG_HFSPLUS_FS is not set
+# CONFIG_BEFS_FS is not set
+# CONFIG_BFS_FS is not set
+# CONFIG_EFS_FS is not set
+CONFIG_JFFS2_FS=y
+CONFIG_JFFS2_FS_DEBUG=0
+CONFIG_JFFS2_FS_WRITEBUFFER=y
+# CONFIG_JFFS2_FS_WBUF_VERIFY is not set
+# CONFIG_JFFS2_SUMMARY is not set
+# CONFIG_JFFS2_FS_XATTR is not set
+# CONFIG_JFFS2_COMPRESSION_OPTIONS is not set
+CONFIG_JFFS2_ZLIB=y
+# CONFIG_JFFS2_LZO is not set
+CONFIG_JFFS2_RTIME=y
+# CONFIG_JFFS2_RUBIN is not set
+# CONFIG_CRAMFS is not set
+# CONFIG_SQUASHFS is not set
+# CONFIG_VXFS_FS is not set
+# CONFIG_MINIX_FS is not set
+# CONFIG_OMFS_FS is not set
+# CONFIG_HPFS_FS is not set
+# CONFIG_QNX4FS_FS is not set
+# CONFIG_ROMFS_FS is not set
+# CONFIG_SYSV_FS is not set
+# CONFIG_UFS_FS is not set
+# CONFIG_NILFS2_FS is not set
+CONFIG_NETWORK_FILESYSTEMS=y
+CONFIG_NFS_FS=y
+CONFIG_NFS_V3=y
+# CONFIG_NFS_V3_ACL is not set
+# CONFIG_NFS_V4 is not set
+CONFIG_ROOT_NFS=y
+# CONFIG_NFSD is not set
+CONFIG_LOCKD=y
+CONFIG_LOCKD_V4=y
+CONFIG_NFS_COMMON=y
+CONFIG_SUNRPC=y
+# CONFIG_RPCSEC_GSS_KRB5 is not set
+# CONFIG_RPCSEC_GSS_SPKM3 is not set
+CONFIG_SMB_FS=m
+CONFIG_SMB_NLS_DEFAULT=y
+CONFIG_SMB_NLS_REMOTE="cp437"
+CONFIG_CIFS=m
+CONFIG_CIFS_STATS=y
+# CONFIG_CIFS_STATS2 is not set
+CONFIG_CIFS_WEAK_PW_HASH=y
+CONFIG_CIFS_XATTR=y
+CONFIG_CIFS_POSIX=y
+# CONFIG_CIFS_DEBUG2 is not set
+# CONFIG_CIFS_EXPERIMENTAL is not set
+# CONFIG_NCP_FS is not set
+# CONFIG_CODA_FS is not set
+# CONFIG_AFS_FS is not set
+
+#
+# Partition Types
+#
+# CONFIG_PARTITION_ADVANCED is not set
+CONFIG_MSDOS_PARTITION=y
+CONFIG_NLS=y
+CONFIG_NLS_DEFAULT="iso8859-1"
+CONFIG_NLS_CODEPAGE_437=y
+# CONFIG_NLS_CODEPAGE_737 is not set
+# CONFIG_NLS_CODEPAGE_775 is not set
+CONFIG_NLS_CODEPAGE_850=y
+# CONFIG_NLS_CODEPAGE_852 is not set
+# CONFIG_NLS_CODEPAGE_855 is not set
+# CONFIG_NLS_CODEPAGE_857 is not set
+# CONFIG_NLS_CODEPAGE_860 is not set
+# CONFIG_NLS_CODEPAGE_861 is not set
+# CONFIG_NLS_CODEPAGE_862 is not set
+# CONFIG_NLS_CODEPAGE_863 is not set
+# CONFIG_NLS_CODEPAGE_864 is not set
+# CONFIG_NLS_CODEPAGE_865 is not set
+# CONFIG_NLS_CODEPAGE_866 is not set
+# CONFIG_NLS_CODEPAGE_869 is not set
+# CONFIG_NLS_CODEPAGE_936 is not set
+# CONFIG_NLS_CODEPAGE_950 is not set
+# CONFIG_NLS_CODEPAGE_932 is not set
+# CONFIG_NLS_CODEPAGE_949 is not set
+# CONFIG_NLS_CODEPAGE_874 is not set
+# CONFIG_NLS_ISO8859_8 is not set
+# CONFIG_NLS_CODEPAGE_1250 is not set
+# CONFIG_NLS_CODEPAGE_1251 is not set
+# CONFIG_NLS_ASCII is not set
+CONFIG_NLS_ISO8859_1=y
+# CONFIG_NLS_ISO8859_2 is not set
+# CONFIG_NLS_ISO8859_3 is not set
+# CONFIG_NLS_ISO8859_4 is not set
+# CONFIG_NLS_ISO8859_5 is not set
+# CONFIG_NLS_ISO8859_6 is not set
+# CONFIG_NLS_ISO8859_7 is not set
+# CONFIG_NLS_ISO8859_9 is not set
+# CONFIG_NLS_ISO8859_13 is not set
+# CONFIG_NLS_ISO8859_14 is not set
+# CONFIG_NLS_ISO8859_15 is not set
+# CONFIG_NLS_KOI8_R is not set
+# CONFIG_NLS_KOI8_U is not set
+CONFIG_NLS_UTF8=y
+# CONFIG_DLM is not set
+
+#
+# Kernel hacking
+#
+# CONFIG_PRINTK_TIME is not set
+CONFIG_ENABLE_WARN_DEPRECATED=y
+CONFIG_ENABLE_MUST_CHECK=y
+CONFIG_FRAME_WARN=1024
+CONFIG_MAGIC_SYSRQ=y
+# CONFIG_UNUSED_SYMBOLS is not set
+CONFIG_DEBUG_FS=y
+# CONFIG_HEADERS_CHECK is not set
+CONFIG_DEBUG_KERNEL=y
+# CONFIG_DEBUG_SHIRQ is not set
+CONFIG_DETECT_SOFTLOCKUP=y
+# CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC is not set
+CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC_VALUE=0
+CONFIG_DETECT_HUNG_TASK=y
+# CONFIG_BOOTPARAM_HUNG_TASK_PANIC is not set
+CONFIG_BOOTPARAM_HUNG_TASK_PANIC_VALUE=0
+CONFIG_SCHED_DEBUG=y
+# CONFIG_SCHEDSTATS is not set
+# CONFIG_TIMER_STATS is not set
+# CONFIG_DEBUG_OBJECTS is not set
+# CONFIG_DEBUG_RT_MUTEXES is not set
+# CONFIG_RT_MUTEX_TESTER is not set
+# CONFIG_DEBUG_SPINLOCK is not set
+# CONFIG_DEBUG_MUTEXES is not set
+# CONFIG_DEBUG_LOCK_ALLOC is not set
+# CONFIG_PROVE_LOCKING is not set
+# CONFIG_LOCK_STAT is not set
+# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
+# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
+# CONFIG_DEBUG_KOBJECT is not set
+CONFIG_DEBUG_BUGVERBOSE=y
+# CONFIG_DEBUG_INFO is not set
+# CONFIG_DEBUG_VM is not set
+# CONFIG_DEBUG_WRITECOUNT is not set
+# CONFIG_DEBUG_MEMORY_INIT is not set
+# CONFIG_DEBUG_LIST is not set
+# CONFIG_DEBUG_SG is not set
+# CONFIG_DEBUG_NOTIFIERS is not set
+CONFIG_FRAME_POINTER=y
+# CONFIG_BOOT_PRINTK_DELAY is not set
+# CONFIG_RCU_TORTURE_TEST is not set
+# CONFIG_RCU_CPU_STALL_DETECTOR is not set
+# CONFIG_BACKTRACE_SELF_TEST is not set
+# CONFIG_DEBUG_BLOCK_EXT_DEVT is not set
+# CONFIG_FAULT_INJECTION is not set
+# CONFIG_PAGE_POISONING is not set
+CONFIG_TRACING_SUPPORT=y
+
+#
+# Tracers
+#
+# CONFIG_IRQSOFF_TRACER is not set
+# CONFIG_SCHED_TRACER is not set
+# CONFIG_CONTEXT_SWITCH_TRACER is not set
+# CONFIG_EVENT_TRACER is not set
+# CONFIG_BOOT_TRACER is not set
+# CONFIG_TRACE_BRANCH_PROFILING is not set
+# CONFIG_KMEMTRACE is not set
+# CONFIG_WORKQUEUE_TRACER is not set
+# CONFIG_BLK_DEV_IO_TRACE is not set
+# CONFIG_DYNAMIC_DEBUG is not set
+# CONFIG_SAMPLES is not set
+
+#
+# Security options
+#
+# CONFIG_KEYS is not set
+# CONFIG_SECURITY is not set
+# CONFIG_SECURITYFS is not set
+# CONFIG_SECURITY_FILE_CAPABILITIES is not set
+# CONFIG_CRYPTO is not set
+# CONFIG_BINARY_PRINTF is not set
+
+#
+# Library routines
+#
+CONFIG_BITREVERSE=y
+CONFIG_GENERIC_FIND_LAST_BIT=y
+CONFIG_CRC_CCITT=y
+# CONFIG_CRC16 is not set
+# CONFIG_CRC_T10DIF is not set
+# CONFIG_CRC_ITU_T is not set
+CONFIG_CRC32=y
+# CONFIG_CRC7 is not set
+# CONFIG_LIBCRC32C is not set
+CONFIG_ZLIB_INFLATE=y
+CONFIG_ZLIB_DEFLATE=y
+CONFIG_DECOMPRESS_GZIP=y
+CONFIG_GENERIC_ALLOCATOR=y
+CONFIG_HAS_IOMEM=y
+CONFIG_HAS_IOPORT=y
+CONFIG_HAS_DMA=y
+CONFIG_NLATTR=y

arch/avr32/include/asm/hw_irq.h

 #ifndef __ASM_AVR32_HW_IRQ_H
 #define __ASM_AVR32_HW_IRQ_H
 
-static inline void hw_resend_irq(struct hw_interrupt_type *h, unsigned int i)
+static inline void hw_resend_irq(struct irq_chip *h, unsigned int i)
 {
 	/* Nothing to do */
 }

drivers/mmc/host/atmel-mci.c

@@ -177,6 +177,7 @@ struct atmel_mci {
  *	available.
  * @wp_pin: GPIO pin used for card write protect sending, or negative
  *	if not available.
+ * @detect_is_active_high: The state of the detect pin when it is active.
  * @detect_timer: Timer used for debouncing @detect_pin interrupts.
  */
 struct atmel_mci_slot {
@@ -196,6 +197,7 @@ struct atmel_mci_slot {
 
 	int			detect_pin;
 	int			wp_pin;
+	bool			detect_is_active_high;
 
 	struct timer_list	detect_timer;
 };
@@ -924,7 +926,8 @@ static int atmci_get_cd(struct mmc_host *mmc)
 	struct atmel_mci_slot	*slot = mmc_priv(mmc);
 
 	if (gpio_is_valid(slot->detect_pin)) {
-		present = !gpio_get_value(slot->detect_pin);
+		present = !(gpio_get_value(slot->detect_pin) ^
+			    slot->detect_is_active_high);
 		dev_dbg(&mmc->class_dev, "card is %spresent\n",
 				present ? "" : "not ");
 	}
@@ -1028,7 +1031,8 @@ static void atmci_detect_change(unsigned long data)
 		return;
 
 	enable_irq(gpio_to_irq(slot->detect_pin));
-	present = !gpio_get_value(slot->detect_pin);
+	present = !(gpio_get_value(slot->detect_pin) ^
+		    slot->detect_is_active_high);
 	present_old = test_bit(ATMCI_CARD_PRESENT, &slot->flags);
 
 	dev_vdbg(&slot->mmc->class_dev, "detect change: %d (was %d)\n",
@@ -1456,6 +1460,7 @@ static int __init atmci_init_slot(struct atmel_mci *host,
 	slot->host = host;
 	slot->detect_pin = slot_data->detect_pin;
 	slot->wp_pin = slot_data->wp_pin;
+	slot->detect_is_active_high = slot_data->detect_is_active_high;
 	slot->sdc_reg = sdc_reg;
 
 	mmc->ops = &atmci_ops;
@@ -1477,7 +1482,8 @@ static int __init atmci_init_slot(struct atmel_mci *host,
 		if (gpio_request(slot->detect_pin, "mmc_detect")) {
 			dev_dbg(&mmc->class_dev, "no detect pin available\n");
 			slot->detect_pin = -EBUSY;
-		} else if (gpio_get_value(slot->detect_pin)) {
+		} else if (gpio_get_value(slot->detect_pin) ^
+				slot->detect_is_active_high) {
 			clear_bit(ATMCI_CARD_PRESENT, &slot->flags);
 		}
 	}

include/linux/atmel-mci.h

@@ -10,6 +10,7 @@
  * @bus_width: Number of data lines wired up the slot
  * @detect_pin: GPIO pin wired to the card detect switch
  * @wp_pin: GPIO pin wired to the write protect sensor
+ * @detect_is_active_high: The state of the detect pin when it is active
  *
  * If a given slot is not present on the board, @bus_width should be
  * set to 0. The other fields are ignored in this case.
@@ -24,6 +25,7 @@ struct mci_slot_pdata {
 	unsigned int		bus_width;
 	int			detect_pin;
 	int			wp_pin;
+	bool			detect_is_active_high;
 };
 
 /**