fw_core_handle_bus_reset() incorrectly relied on the assumption that
self_id_count > 0.

We check early in fw-ohci and discard the self ID complete event if
self_id_count == 0 because a valid event always has at least one self ID
packet in it (the one of the local node).  Hence treat self_id_count ==
0 like any other kind of invalid self ID buffer.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Jarod Wilson <jwilson@redhat.com>

Discard self ID buffer contents if
  - the selfIDError flag is set,
  - any of the self ID packets has bit errors.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Jarod Wilson <jwilson@redhat.com>

Clean up shared code and variable names.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

The platform feature calls in the suspend method switched off cable
power, but the calls in the resume method did not switch it back on.

Add the necessary feature call to .resume.  Also add the corresponding
call to .suspend to make .suspend's behavior explicitly the same on all
PMacs.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

This way firewire-ohci can be used for remote debugging like ohci1394.
Version with amendment from Fri, 11 Apr 2008 00:08:08 +0200.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Acked-by: Bernhard Kaindl <bk@suse.de>

Try to write dual-phase retry protocol limits to BUSY_TIMEOUT register.
- The dual-phase retry protocol is optional to implement, and if not 
  supported, writes to the dual-phase portion of the register will be
  ignored. We try to write the original 1394-1995 default here.
- In the case of devices that are also SBP-3-compliant, all writes are 
  ignored, as the register is read-only, but contains single-phase retry of
  15, which is what we're trying to set for all SBP-2 device anyway, so this
  write attempt is safe and yields more consistent behavior for all devices.

See section 8.3.2.3.5 of the 1394-1995 spec, section 6.2 of the SBP-2 spec,
and section 6.4 of the SBP-3 spec for further details.
Signed-off-by: Jarod Wilson <jwilson@redhat.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

The block/unblock logic is now sufficiently tested.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

orb came from kzalloc.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

How hard can it be to switch on one bit? :-)
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

Write directly in big endian instead of byte-swapping after the fact.
This saves a few conversions, lets gcc use constant endianess
conversions where possible, and enables deeper endianess annotation.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

Add wrappers for getting and putting a unit.
Remove some line breaks.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Jarod Wilson <jwilson@redhat.com>

The reference count of the unit dropped too low in an error path in
sbp2_probe.  Fixed by moving the _get further up.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Jarod Wilson <jwilson@redhat.com>

The card->kref became obsolete since patch "firewire: fix crash in
automatic module unloading" added another counter of card users.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Jarod Wilson <jwilson@redhat.com>

The following patch limits the node speed to the host interface speed,
before using it.
Signed-off-by: Philippe De Muyter <phdm@macqel.be>

It should actually suffice to do this only for the local node's
speedcap[].  But there is another bug in the speed calculation:
The local node's speed is not correctly propagated to the speeds
which are to be used to access remote nodes.
http://thread.gmane.org/gmane.linux.kernel.firewire.devel/11772/focus=12024Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

Unless you're adding a kobject to the sysfs hierarchy, there is no
point setting its kobject name.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

The failure path of ohci1394_pci_probe() reuses ohci1394_pci_remove().
Doing so it missed to call ohci1394_pmac_off() in a few unlikely early
error cases.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

to reduce the size of ohci1394.ko.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

We don't want to hide something like return in a preprocessor macro.
Unroll the macro and use a goto, which also reduces the size of
ohci1394.ko.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

Clean up shared code and variable names.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

The platform feature calls in the suspend method switched off cable
power, but the calls in the resume method did not switch it back on.

Add the necessary feature call to .resume.  Also add the corresponding
call to .suspend to make .suspend's behavior explicitly the same on all
PMacs.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

These drivers don't need to match any unit_directory type device.
They just need the id_table for module autoloading per module alias.

Not binding any of these drivers allows special-purpose drivers with
similar or same IDs to bind to devices.  This currently only benefits
out-of-tree drivers; on the other hand it is in no way detrimental to
in-tree drivers.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

replace all:
big_endian_variable = cpu_to_beX(beX_to_cpu(big_endian_variable) +
					expression_in_cpu_byteorder);
with:
	beX_add_cpu(&big_endian_variable, expression_in_cpu_byteorder);
generated with semantic patch
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6:
  it821x: do not describe noraid parameter with its value
  Pb1200/DBAu1200: fix bad IDE resource size
  Au1200: IDE driver build fix
  Au1200: kill IDE driver function prototypes
  avr32 mustn't select HAVE_IDE

Describe noraid parameter with its name (and not its value).
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

The header files for the Pb1200/DBAu1200 boards have wrong definition for the
IDE interface's decoded range length -- it should be 512 bytes according to
what the IDE driver does.  In addition, the IDE platform device claims 1 byte
too many for its memory resource -- fix the platform code and the IDE driver
in accordance.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

The driver fails to compile with CONFIG_BLK_DEV_IDE_AU1XXX_MDMA2_DBDMA enabled:

drivers/ide/mips/au1xxx-ide.c: In function `auide_build_dmatable':
drivers/ide/mips/au1xxx-ide.c:256: error: implicit declaration of function
`sg_virt'
drivers/ide/mips/au1xxx-ide.c:275: error: implicit declaration of function
`sg_next'
drivers/ide/mips/au1xxx-ide.c:275: warning: assignment makes pointer from
integer without a cast

Fix this by including <linux/scatterlist.h>. While at it, remove the #include's
without which the driver happily builds.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Fix these warnings emitted when compiling drivers/ide/mips/au1xxx-ide.c:

include/asm/mach-au1x00/au1xxx_ide.h:137: warning: 'auide_tune_drive' declared 
`static' but never defined
include/asm/mach-au1x00/au1xxx_ide.h:138: warning: 'auide_tune_chipset' declared
 `static' but never defined

by wiping out the whole "function prototyping" section from the header file
<asm-mips/mach-au1x00/au1xxx_ide.h> as it mostly declared functions that are
already dead in the IDE driver; move the only useful prototype into the driver.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

There's a libata based PATA driver for avr32, but no support for 
drivers/ide/ on avr32.

This patch fixes the following compile error:

<--  snip  -->

...
  CC [M]  drivers/ide/ide-cd.o
In file included from /home/bunk/linux/kernel-2.6/git/linux-2.6/drivers/ide/ide-cd.c:37:
/home/bunk/linux/kernel-2.6/git/linux-2.6/include/linux/ide.h:209:21: error: asm/ide.h: No such file or directory
make[3]: *** [drivers/ide/ide-cd.o] Error 1

<--  snip  -->
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
  block: update git url for blktrace
  io context: increment task attachment count in ioc_task_link()

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
  USB: remove broken usb-serial num_endpoints check
  USB: option: Add new vendor ID and device ID for AMOI HSDPA modem
  USB: support more Huawei data card product IDs
  USB: option.c: add more device IDs
  USB: Obscure Maxon BP3-USB Device Support 16d8:6280 for option driver

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
  [TCP]: Add return value indication to tcp_prune_ofo_queue().
  PS3: gelic: fix the oops on the broken IE returned from the hypervisor
  b43legacy: fix DMA mapping leakage
  mac80211: remove message on receiving unexpected unencrypted frames
  Update rt2x00 MAINTAINERS entry
  Add rfkill to MAINTAINERS file
  rfkill: Fix device type check when toggling states
  b43legacy: Fix usage of struct device used for DMAing
  ssb: Fix usage of struct device used for DMAing
  MAINTAINERS: move to generic repository for iwlwifi
  b43legacy: fix initvals loading on bcm4303
  rtl8187: Add missing priv->vif assignments
  netconsole: only set CON_PRINTBUFFER if the user specifies a netconsole
  [CAN]: Update documentation of struct sockaddr_can
  MAINTAINERS: isdn4linux@listserv.isdn4linux.de is subscribers-only
  [TCP]: Fix never pruned tcp out-of-order queue.
  [NET_SCHED] sch_api: fix qdisc_tree_decrease_qlen() loop

Describe debug parameters with their names (and not their values).
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The num_interrupt_in, num_bulk_in, and other checks in the usb-serial
code are just wrong, there are too many different devices out there with
different numbers of endpoints.  We need to just be sticking with the
device ids instead of trying to catch this kind of thing.  It broke too
many different devices.

This fixes a large number of usb-serial devices to get them working
properly again.


Cc: Oliver Neukum <oliver@neukum.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch add new vendor ID and device ID  for AMOI HSDPA modem. 

From: tang kai <tangk73@hotmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

 - declare the unusal device for Huawei data card devices in
   unusual_devs.h
 - disable the product ID matching for Huawei data card devices in
   usb_match_device function of driver.c
 - declare the product IDs in option.c.
Signed-off-by: fangxiaozhi <huananhu@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>