For ARMv7 kernels running in the non-secure world, writing to the
auxillary control register causes an abort, so we must avoid directly
writing the auxillary control register.  If the ACR has already been
reinitialized by SoC code, don't try to restore it.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Add a dsb after the isb to ensure that the previous writes to the
CP15 registers take effect before we enable the MMU.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

ARM920 and ARM926 save four registers, not three.  Fix the size of
the suspend region required.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

r1 stores the v:p offset from the CPU invariant resume code, and is
expected to be preserved by the CPU specific code.  Overwriting it is
not a good idea.

We've managed to get away with it on sa1100 platforms because most
happen to have PHYS_OFFSET == PAGE_OFFSET, but that may not be the
case depending on kernel configuration.  So fix this latent bug.

This fixes xsc3 as well which was saving and restoring this register
independently.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

cpu_v7_reset disables the MMU and then branches to the provided address.
On Thumb-2 kernels, we should take care to clear the Thumb Exception
enable bit in the System Control Register, otherwise this may wreak
havok in the code to which we are branching (for example, an ARM kernel
image via kexec).
Reviewed-by: Dave Martin <dave.martin@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Commit 540b5738 ("ARM: 6999/1: head, zImage: Always Enter the kernel in
ARM state") mandates that the kernel should be entered in ARM state.

If a Thumb-2 kernel kexecs a new kernel image, we need to ensure that
we change state when branching to the new code. This patch replaces a
mov pc, lr with a bx lr on Thumb-2 kernels so that we transition to ARM
state if need be.
Reviewed-by: Dave Martin <dave.martin@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

It seems that an entry for the SP805 watchdog in the table of clocks was
missing.  This results in the sp805_wdt driver rejecting the device with
the following errors:

  sp805-wdt mb:wdt: Clock not found
  sp805-wdt mb:wdt: Probe Failed!!!
  sp805-wdt: probe of mb:wdt failed with error -2

While not obviously stated in the hardware docs, the onboard SP810's
"REFCLK" is connected to a 32.768KHz crystal, and this drives the
watchdog.  Add a struct clk and corresponding lookup entry for it.
Signed-off-by: Nick Bowler <nbowler@elliptictech.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

I made some changes to the entry in the ARM Machine Registry after
submission which was the wrong thing to do.
This patch should help to fix this error.
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Since commit 8560a6cf
"arm: Footbridge: Use common i8253 clockevent",
ARCH_NETWINDER needs to select CLKEVT_I8253.

This patch fixes below build error with "make netwinder_defconfig".

  LD      .tmp_vmlinux1
arch/arm/mach-footbridge/built-in.o: In function `isa_timer_init':
isa-rtc.c:(.init.text+0x12c8): undefined reference to `clockevent_i8253_init'
isa-rtc.c:(.init.text+0x12d0): undefined reference to `i8253_clockevent'
arch/arm/mach-footbridge/built-in.o:(.data+0x198): undefined reference to `i8253_clockevent'
make: *** [.tmp_vmlinux1] Error 1
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

This patch is a workaround for the 364296 ARM1136 r0p2 erratum (possible
cache data corruption with hit-under-miss enabled). It sets the
undocumented bit 31 in the auxiliary control register and the FI bit in
the control register, thus disabling hit-under-miss without putting the
processor into full low interrupt latency mode.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

This patch fixes L2 Cache size calculations for L2C-210, L2C-310 and
PL310, by changing the L2X0_AUX_CTRL_WAY_SIZE_MASK from 2 bits to 3
bits.

The Auxiliary Control Register for L2C-210, L2C-310 and PL310 has 3bits
[19:17] for Way size, however the existing code only uses 2 bits to
get this value. This results in incorrect cachesize calculations.

It also results in performing operations on the whole cache when we
erroneously decide that the range is big enough (due to l2x0_size being
too small) and also prints incorrect cachesize.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Cc: stable@kernel.org
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Fix the obvious error in board detection logic, because according to the TS's
manual, the model is stored in the least three significant bits. For example
the byte read on my ts-7300 is 0x23 and the detection then fails.

Cc: Ryan Mallon <ryan@bluewatersys.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Cc: Ryan Mallon <ryan@bluewatersys.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

* 'devicetree/merge' of git://git.secretlab.ca/git/linux-2.6:
  dt: add empty of_get_property for non-dt

* 'usb-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (30 commits)
  USB: Serial: Add PID(0xF7C0) to FTDI SIO driver for a zeitcontrol-device
  USB: Serial: Add device ID for Sierra Wireless MC8305
  USB: Serial: Added device ID for Qualcomm Modem in Sagemcom's HiLo3G
  usb/host/pci-quirks.c: correct annotation of `ehci_dmi_nohandoff_table'
  USB: option driver: add PID for Vodafone-Huawei K4511
  USB: option driver: add PID for Vodafone-Huawei K4510
  USB: option driver: add PID for Vodafone-Huawei K3771
  USB: option driver: add PID for Vodafone-Huawei K3770
  usb: serial: ftdi_sio.c: For the FT232H FTDI_SIO_SET_BAUDRATE_REQUEST, index needs to be shifted too
  usb/isp1760: Added missing call to usb_hcd_check_unlink_urb() during unlink
  USB: EHCI: Fix test mode sequence
  USB: ftdi_sio: fix minor typo in get_ftdi_divisor
  USB: at91_udc: include linux/prefetch.h explicitly
  USB: usb-storage: unusual_devs entry for ARM V2M motherboard.
  usb/ehci-mxc: add missing inclusion of mach/hardware.h
  USB: assign instead of equal in usbtmc.c
  usb: renesas_usbhs: fixup usbhsg_for_each_uep 1st pos
  usb: renesas_usbhs: fix DMA build by including dma-mapping.h
  usb: gadget: net2272 - Correct includes
  usb: musb: fix oops on musb_gadget_pullup
  ...

* 'staging-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6:
  zcache: Fix build error when sysfs is not defined
  zcache: Use div_u64 for 64-bit division
  staging:rts_pstor: fix thread synchronization flow
  drivers:staging:solo6x10:add the missed slab.h
  staging: zcache: include module.h for MODULE_LICENSE
  drivers/staging/hv/blkvsc_drv.c: eliminate NULL pointer dereference
  Staging: Add clk API note to nvec/TODO
  drivers/staging/ath6kl/miscdrv/ar3kps/ar3kpsparser.c: adjust array index
  staging: more missing slab.h inclusions
  drivers/staging/solo6x10/p2m.c needs slab.h
  drivers/staging/solo6x10/core.c needs slab.h
  drivers/staging/dt3155v4l/dt3155v4l.c needs slab.h
  drivers/staging/speakup/devsynth.c: fix "buffer size is not provably correct" error
  Staging: iio: add some unlocks to raw_read() functions
  staging: ft1000_proc needs asm/io.h for inw/outw on sparc
  staging: rtl8192u: declare MODULE_FIRMWARE
  gma500: Fix clashes with DRM updates
  staging: zcache: module is GPL
  staging: fix zcache building

* 'x86-vdso-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-tip:
  x86-64: Rework vsyscall emulation and add vsyscall= parameter
  x86-64: Wire up getcpu syscall
  x86: Remove unnecessary compile flag tweaks for vsyscall code
  x86-64: Add vsyscall:emulate_vsyscall trace event
  x86-64: Add user_64bit_mode paravirt op
  x86-64, xen: Enable the vvar mapping
  x86-64: Work around gold bug 13023
  x86-64: Move the "user" vsyscall segment out of the data segment.
  x86-64: Pad vDSO to a page boundary

* 'for-linus' of git://oss.sgi.com/xfs/xfs:
  xfs: replace xfs_buf_geterror() with bp->b_error
  xfs: Check the return value of xfs_buf_read() for NULL
  "xfs: fix error handling for synchronous writes" revisited
  xfs: set cursor in xfs_ail_splice() even when AIL was empty
  xfs: Remove the macro XFS_BUFTARG_NAME
  xfs: Remove the macro XFS_BUF_TARGET
  xfs: Remove the macro XFS_BUF_SET_TARGET
  Replace the macro XFS_BUF_ISPINNED with helper xfs_buf_ispinned
  xfs: Remove the macro XFS_BUF_SET_PTR
  xfs: Remove the macro XFS_BUF_PTR
  xfs: Remove macro XFS_BUF_SET_START
  xfs: Remove macro XFS_BUF_HOLD
  xfs: Remove macro XFS_BUF_BUSY and family
  xfs: Remove the macro XFS_BUF_ERROR and family
  xfs: Remove the macro XFS_BUF_BFLAGS

* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc: (32 commits)
  ARM: mmp: Change the way we use timer 0 as clockevent timer.
  ARM: mmp: Switch to using timer 1 as clocksource timer.
  ARM: mmp: Also start timer 1 on boot.
  ARM: pxa168/gplugd: free correct GPIO
  ARM: pxa168/gplugd: get rid of mfp-gplugd.h
  ARM: pxa: fix logic error in PJ4 iWMMXt handling
  mach-sa1100: fix PCI build problem
  omap: timer: Set dmtimer used as clocksource in autoreload mode
  OMAP3: am3517crane: remove NULL board_mux from board file
  arm: mach-omap2: mux: use kstrdup()
  arch:arm:plat-omap:iovmm: remove unused variable 'va'
  Update Nook Color machine 3284 to common Encore name
  am3505/3517: Various platform defines for UART4
  OMAP: hwmod: fix build break on non-OMAP4 multi-OMAP2 builds
  OMAP: Fix linking error in twl-common.c for OMAP2/3/4 only builds
  iMX: Fix build for iMX53
  ARM: mx5: board-cpuimx51.c fixup irq_to_gpio() usage
  OMAP2+: PM: SmartReflex: use put_sync_suspend for IRQ-safe disabling
  OMAP3: beagle: don't touch omap_device internals
  OMAP1: enable GENERIC_IRQ_CHIP
  ...

Since we just checked bp for NULL, it is ok to replace
xfs_buf_geterror() with bp->b_error in these places.
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: Alex Elder <aelder@sgi.com>

Check the return value of xfs_buf_read() for NULL and return ENOMEM
if it is NULL.  This is necessary in a few spots to avoid subsequent
code blindly dereferencing the null buffer pointer.
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: Alex Elder <aelder@sgi.com>

Merge branch 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6 into fixes

The current cache detection code does not check for an aliasing
I-cache if the D-cache is found to be VIPT aliasing.

This patch fixes the problem by always checking for an aliasing
I-cache on v6 and later.
Signed-off-by: Will Deacon <will.deacon@arm.com>

The smp_twd clockevents driver currently enables the local timer PPI
before the clockevents device is registered. This can lead to a kernel
panic if a spurious timer interrupt is generated before registration
has completed since the kernel will treat it as an IPI timer.

This patch moves the clockevents device registration before the IRQ
unmasking so that we can always handle timer interrupts once they can
occur.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>

The various reset routines in mach-realview rely on an FPGA to
power-cycle the board after writing some magic runes to memory-mapped
registers.

This patch adds a dsb() following the writes, so that they become
visible before we mdelay(1000) in the arch_reset code. Without this
patch, the timeout would expire sporadically, causing the reset to fail.
Signed-off-by: Will Deacon <will.deacon@arm.com>

Commit f12482c9 ("ARM: 6974/1: pmu: refactor reservation") changed
{release,reserve}_pmu to take an enum arm_pmu_type as a parameter, but
inconsistently named the parameter `type' or `device'. It would be nice
if these were consistent.

This patch makes use of enum arm_pmu_type consistent, always using
`type'. Related printks are updated, explicitly mentioning `type' also.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>

Commit  f12482c9 ("ARM: 6974/1: pmu: refactor reservation") changed the
prototype of release_pmu, but missed the stub for when
CONFIG_CPU_HAS_PMU is not selected by the platform.

This patch changes the prototype of the stub, preventing possible build
failures when CONFIG_CPU_HAS_PMU is not selected.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>

libio.h is not provided by uClibc, in order to be able to test the
definition of __UCLIBC__ we need to include stdlib.h, which also
includes stddef.h, providing the definition of 'NULL'.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (44 commits)
  e1000e: increase driver version number
  e1000e: alternate MAC address update
  e1000e: do not disable receiver on 82574/82583
  e1000e: alternate MAC address does not work on device id 0x1060
  PCnet: Fix section mismatch
  bnx2x: disable dcb on 578xx since not supported yet
  bnx2x: properly clean indirect addresses
  bnx2x: prevent race between undi_unload and load flows
  bnx2x: fix select_queue when FCoE is disabled
  bnx2x: init FCOE FP only once
  ipv4: some rt_iif -> rt_route_iif conversions
  net/bridge/netfilter/ebtables.c: use available error handling code
  net/netlabel/netlabel_kapi.c: add missing cleanup code
  net/irda: sh_sir: tidyup compile warning
  net/irda: sh_sir: add missing header
  net/irda: sh_irda: add missing header
  slcan: ldisc generated skbs are received in softirq context
  scm: Capture the full credentials of the scm sender
  tcp: initialize variable ecn_ok in syncookies path
  drivers/net/wireless/wl1251: add missing kfree
  ...

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
  sparc: Don't do hypervisor calls on non-sun4v in DS driver.

Reported-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Just like files-layout, blocks & objects layouts are part of the
NFS 4.1 protocol and should be automatically selected if NFS_4_1
is selected. The small problem is that these depend on other
Kernel support being present, while files only depends on NFS
itself.

This patch removes from the user choice the presence of objects
and blocks layout. But makes sure these are selected only if
the depended subsystems are present in the Kernel.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Acked-by: Peng Tao <peng_tao@emc.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Commit df5e6223 ("ext4: fix deadlock in ext4_symlink() in ENOSPC
conditions") recalculated the number of credits needed for a long
symlink, in the process of splitting it into two transactions.  However,
the first credit calculation under-counted because if selinux is
enabled, credits are needed to create the selinux xattr as well.

Overrunning the reservation will result in an OOPS in
jbd2_journal_dirty_metadata() due to this assert:

  J_ASSERT_JH(jh, handle->h_buffer_credits > 0);

Fix this by increasing the reservation size.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Acked-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Commit ae54870a ("ext3: Fix lock inversion in ext3_symlink()")
recalculated the number of credits needed for a long symlink, in the
process of splitting it into two transactions.  However, the first
credit calculation under-counted because if selinux is enabled, credits
are needed to create the selinux xattr as well.

Overrunning the reservation will result in an OOPS in
journal_dirty_metadata() due to this assert:

  J_ASSERT_JH(jh, handle->h_buffer_credits > 0);

Fix this by increasing the reservation size.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Acked-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

If word 0x37 in the EEPROM is 0xFFFF _or_ 0x0000, then there is no
alternate MAC address in the EEPROM.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>