Merge tag 'renesas-arm-dt-for-v4.19' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt

Renesas ARM Based SoC DT Updates for v4.19

* RZ/G1C (r8a77470) SoC: Use r8a77470-cpg-mssr binding definitions
* Add GR-Peach audio camera shield support with MT9V111 image sensor
* Add initial support for RZ/N1D (r9a06g032) SoC and its RZN1D-DB board
* Use SPDX identifiers in DT for all SoCs and boards
* Add missing OPP properties for all CPUs on various SoCs
* Add missing PMIC nodes to R-Car Gen2 M2-W (r8a7791) based porter board

* tag 'renesas-arm-dt-for-v4.19' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
  ARM: dts: r8a77470: Use r8a77470-cpg-mssr binding definitions
  ARM: dts: gr-peach: Add GR-Peach audiocamerashield support
  ARM: dts: Renesas R9A06G032 SMP enable method
  ARM: dts: Renesas RZN1D-DB Board base file
  ARM: dts: Renesas R9A06G032 base device tree file
  ARM: dts: convert to SPDX identifier for Renesas boards
  ARM: dts: r8a77(43|9[013]): Add missing OPP properties for CPUs
  ARM: dts: porter: Add missing PMIC nodes
Signed-off-by: Olof Johansson <olof@lixom.net>

* sprd/dt:
  arm64: dts: sprd: Add one suspend timer
  arm64: dts: sprd: Add SC27XX ADC device
  arm64: dts: sprd: Add SC27XX eFuse device
  arm64: dts: sprd: Add SC27XX vibrator device
  arm64: dts: sprd: Add SC27XX breathing light controller device
Signed-off-by: Olof Johansson <olof@lixom.net>

On Spreadtrum platform, the current clocksource for timekeeping will be
stopped in suspend state, thus add one always-on timer to calculate the
suspend time.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>

Add the Spreadtrum SC27XX PMICs ADC device node which contains 32 channels.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>

This patch adds the eFuse device node for Spreadtrum SC27XX PMICs.
The SC27XX eFuse contains 32 blocks and each block's data width is
16 bits.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>

This patch adds the vibrator device node for Spreadtrum SC27XX PMICs.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>

The SC27xx breathing light controller can support 3 outputs:
red LED, green LED and blue LED.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'qcom-dts-for-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux into next/dt

Qualcomm Device Tree Changes for v4.19

* Add missing OPPs on IPQ4019
* Fix sdhci l20 load on Hammerhead
* Use proper IRQ macros for IPQ8064 interrupts

* tag 'qcom-dts-for-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux:
  ARM: dts: qcom: Add missing OPP properties for CPUs
  ARM: dts: qcom: msm8974-hammerhead: increase load on l20 for sdhci
  ARM: dts: qcom: Fix 'interrupts = <>' property to use proper macros
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'qcom-arm64-for-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux into next/dt

Qualcomm ARM64 Updates for v4.19

* Add support for PM8005/PM8998 and related nodes
* Add/fix nodes on SDM845 for I2c, SPI, UART, and RPMH
* Fix BT LED trigger on DB410c
* Drop legacy clock names on MSM8916
* Add gpio line names on DB820c

* tag 'qcom-arm64-for-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux:
  arm64: dts: qcom: db410c: Fix Bluetooth LED trigger
  arm64: dts: sdm845: Default qupv3_id_0 as "disabled" like _id_1
  arm64: dts: msm8916: drop legacy suffix for clocks used by MSM DRM driver
  arm64: dts: qcom: db820c: Add gpio-line-names property
  arm64: dts: sdm845: Add rpmh-clk node
  arm64: dts: sdm845: Add rpmh-rsc node
  arm64: dts: qcom: sdm845: Enable debug UART and I2C10 on sdm845-mtp
  arm64: dts: qcom: sdm845: Add I2C, SPI, and UART9 nodes
  arm64: dts: qcom: Add pm8005 and pm8998 support
  arm64: dts: qcom: Add pmu node to sdm845
Signed-off-by: Olof Johansson <olof@lixom.net>

Replace the hardcoded clock indices by R8A77470_CLK_* symbols.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add device tree header for GR-Peach's audiocamerashield with MT9V111
image sensor.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add a special enable method for the second CA7 of the R9A06G032
as well as the default value for the "cpu-release-addr" property.
Signed-off-by: Michel Pollet <michel.pollet@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

This adds a base device tree file for the RZN1-DB board, with only the
basic support allowing the system to boot to a prompt. Only one UART is
used, with only a single CPU running.
Signed-off-by: Michel Pollet <michel.pollet@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

This adds the Renesas R9A06G032 bare bone support.

This currently only handles the SYSCTRL block note,
generic parts (gic, architected timer) and a UART.
Signed-off-by: Michel Pollet <michel.pollet@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
[simon: updated MAINTAINERS file
[simon: do not use r9a06g032-sysctrl.h as it is not in the renesas tree yet]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

The OPP properties, like "operating-points", should either be present
for all the CPUs of a cluster or none. If these are present only for a
subset of CPUs of a cluster then things will start falling apart as soon
as the CPUs are brought online in a different order. For example, this
will happen because the operating system looks for such properties in
the CPU node it is trying to bring up, so that it can create an OPP
table.

Add such missing properties.

Fix other missing properties (like, clock latency, voltage tolerance,
etc) as well to make it all work.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Merge tag 'am654-for-v4.19-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt

TI AM654 support for v4.19 merge window

This branch adds initial support for new Texas Instruments AM654
quad core A53 ARMv8 SoC. It's the first device for TI K3 multicore SoC
architecture.

Initially only basic devices are configured, support for more devices
will follow later on. And many of the internal devices familiar from
earlier TI SoCs should work with existing kernel device drivers.

* tag 'am654-for-v4.19-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  arm64: dts: ti: Add support for AM654 EVM base board
  soc: ti: Add Support for AM654 SoC config option
  arm64: dts: ti: Add Support for AM654 SoC
  arm64: Add support for TI's K3 Multicore SoC architecture
  dt-bindings: arm: ti: Add bindings for AM654 SoC
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'imx-dt64-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt

Freescale arm64 device tree update for 4.19:
 - Update device tree sources to use SPDX identifiers for license.
 - Add cooling device property '#cooling-cells' for all CPUs of
   a cluster.

* tag 'imx-dt64-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
  arm64: dts: freescale: Add missing cooling device properties for CPUs
  arm64: dts: freescale: Update to use SPDX identifiers
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'imx-dt-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt

i.MX device tree update for 4.19:
 - Add device tree support for i.MX6SLL SoC.
 - New board support: ConnectCore 6UL System-On-Module and SBC Express;
   ZII SCU2 Mezz, SCU3 ESB, SSMB SPU3 and CFU1 board; i.MX6SLL EVK
   board; Engicam i.CoreM6 1.5 Quad/Dual MIPI; LogicPD MX31Lite board;
   i.MX53 HSC/DDC boards from K+P.
 - Remove fake regulator bus container node and enable USB OTG support
   for i.MX6 wandboard and riotboard.
 - Populate RAVE SP EEPROM, backlight, power button and watchdog devices
   for ZII boards.
 - Add cooling-cells for cpufreq cooling device, and add OPP properties
   for all CPUs.
 - A series from Anson Huang to enable LCD panel and backlight support
   for imx6sll-evk board.
 - Make pfuze100 sw4 regulator always-on for for a few Freescale/NXP
   development boards, because the regulator is critical there and
   cannot be turned off.
 - Add more device support for i.MX5: AIPSTZ, SAHARA Crypto, M4IF,
   Tigerp, PMU, CodaHx4 VPU.
 - Enable PMU secure-reg-access for imx51-babbage, imx51-zii-rdu1 and
   imx53-ppd board.
 - Switch more device tree license to use SPDX identifier.
 - Switch to use OF graph to describe the display for imx7d-nitrogen7.
 - Add chosen/stdout-path for more boards, so that earlycon can be
   enabled more easily on kernel cmdline.
 - Convert GPC to new device tree bindings and add Vivante gpu nodes
   for i.MX6SL SoC.
 - Add more device support for imx6dl-mamoj board: parallel display,
   WiFi and USB.
 - A series from Stefan Agner to update i.MX6 apalis/colibri boards on
   various aspects: SD/MMC card detection, regulators, etc.

* tag 'imx-dt-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (96 commits)
  ARM: dts: imx7d: remove "operating-points" property for cpu1
  ARM: dts: vf610-zii-ssmb-spu3: Fix W=1 level warnings
  ARM: dts: vf610: Add ZII CFU1 board
  ARM: dts: imx6dl-mamoj: Add usb host and device support
  ARM: dts: imx6dl-mamoj: Add Wifi support
  ARM: dts: imx6dl-mamoj: Add parallel display support
  ARM: dts: vf610: Add ZII SSMB SPU3 board
  ARM: dts: imx6ul-pico-hobbit: Do not hardcode the memory size
  ARM: dts: imx6sl-evk: make pfuze100 sw4 always on
  ARM: dts: imx6sll-evk: make pfuze100 sw4 always on
  ARM: dts: imx6sx-sdb-reva: make pfuze100 sw4 always on
  ARM: dts: imx6qdl-sabresd: make pfuze100 sw4 always on
  ARM: dts: imx6sl-evk: add missing GPIO iomux setting
  ARM: dts: imx51-zii-scu3-esb: Fix RAVE SP watchdog compatible string
  ARM: dts: imx51-zii-scu3-esb: Add switch IRQ line pinumx config
  ARM: dts: imx6sx-nitrogen6sx: remove obsolete display configuration
  ARM: dts: imx7d-nitrogen7: use OF graph to describe the display
  ARM: dts: imx: Switch Boundary Devices boards to SPDX identifier
  ARM: dts: imx6sl: Add vivante gpu nodes
  ARM: dts: imx6sll-evk: enable SEIKO 43WVF1G lcdif panel
  ...
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'imx-dt-clkdep-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt

i.MX device tree changes with clock dependency:
 - Add clock for i.MX6UL GPIO blocks

* tag 'imx-dt-clkdep-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
  ARM: dts: imx6ul: add GPIO clocks
  clk: imx6ul: remove clks_init_on array
  clk: imx6ul: add GPIO clock gates
  dt-bindings: clock: imx6ul: Do not change the clock definition order
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'amlogic-dt64-1' of https://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into next/dt

Amlogic 64-bit DT updates for v4.19
- new SoC: S805x
- new board: S805x-based P241 board from Amlogic
- AXG: add ADC support w/buttons, add pins for PDM, SPDIF
- AXG: s400 board: preliminary support for audio
- GX: nanopi-k2: add HDMI, CEC, CVBS support

* tag 'amlogic-dt64-1' of https://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
  ARM64: dts: meson-axg: add pdm pins
  ARM64: dts: meson-axg: add spdif input pins
  ARM64: dts: meson-axg: remove spdif out from gpio a7
  ARM64: dts: meson-axg: add adc buttons the S400
  ARM64: dts: meson-axg: remove vddio_ao18 from SoC dtsi
  ARM64: dts: meson-axg: add saradc support
  ARM64: dts: add S805X based P241 board
  dt-bindings: amlogic: Add support for GXL S805X and the P241 board
  ARM64: dts: amlogic: Add missing cooling device properties for CPUs
  ARM64: dts: meson-axg: add spdif output pins
  ARM64: dts: meson-axg: add s400 speaker amplifier
  ARM64: dts: meson-axg: add s400 main 12v supply
  ARM64: dts: meson-axg: add s400 microphone card leds
  ARM64: dts: meson-gxbb-nanopi-k2: Add HDMI, CEC and CVBS nodes
  ARM64: dts: meson-gx-p23x-q20x: move the wifi node to each board's .dts
  ARM64: dts: meson: enable the saradc node in meson-gx-p23x-q20x.dtsi
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'renesas-dt-bindings-for-v4.19' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt

Renesas ARM Based SoC DT Bindings Updates for v4.19

Bindings relating to initial support for RZ/N1D (R9A06G032) SoC and its
RZN1D-DB board:

* Add Renesas R9A06G032 SMP enable method
* Document SoC and Board bindings

* tag 'renesas-dt-bindings-for-v4.19' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
  dt-bindings: cpu: Add Renesas R9A06G032 SMP enable method.
  dt-bindings: arm: Document the RZN1D-DB board
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'renesas-arm64-dt2-for-v4.19' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt

Second Round of Renesas ARM64 Based SoC DT Updates for v4.19

Corrections:

* Remove non-existing STBE region from Ether-AVB node in DT of
  R-Car E3 (r8a77990) SoC

Cleanups:

* Consistently use rwdt as label for Renesas Watchdog Timer devices
* Add second port to rcar_sound placeholder in DT of R-Car M3-N (r8a77965) SoC
* Fix adv7482 decimal unit addresses in DT of Salvator-X and -XS boards

Enhancements:

* Describe in DT:
  - INTC-EX of R-Car V3H (r8a77980) SoC
  - USB3.0 of R-Car E3 (r8a77980) SoC
  - All SCIF and HSCIF devices of R-Car D3 (r8a77995) SoC.
    Previously only SCIF2, used as the debug consile, was described.
  - All IPMMU devicesof R-Car M3-N (r8a77965), V3H (r8a77980) and
    E3 (r8a77990) SoCs
* Enable USB3.0 in DT of R-Car E3 (r8a77980) based Ebisu board
* Prefer HSCIF1 over SCIF1 in DT of Salvator-X and -XS boards

* tag 'renesas-arm64-dt2-for-v4.19' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
  arm64: dts: renesas: r8a77980: add INTC-EX support
  arm64: dts: renesas: r8a77990: Enable USB3.0 host for Ebisu board
  arm64: dts: renesas: r8a77995: Add SCIF {0,1,3,4,5} and all HSCIF device nodes
  arm64: dts: renesas: r8a779{65,80,90}: Add IPMMU devices nodes
  arm64: dts: renesas: Unify the labels for RWDT
  arm64: dts: renesas: salvator-common: Prefer HSCIF1 over SCIF1
  arm64: dts: renesas: r8a77965: Add second port to rcar_sound placeholder
  arm64: dts: renesas: salvator-common: Fix adv7482 decimal unit addresses
  arm64: dts: renesas: r8a77990: Remove non-existing STBE region
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'at91-ab-4.19-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux into next/dt

AT91 DT for 4.19:

 - New boards from Laird: WB45N, WB50N, SOM60 modules and DVK, Gatwick
 - fix the PMC compatibles

* tag 'at91-ab-4.19-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
  ARM: dts: at91: fix typos for SSC TD functions
  ARM: dts: add support for Laird SOM60 module and DVK boards
  ARM: dts: add support for Gatwick board based on WB50N
  ARM: dts: add support for Laird WB50N cpu module and DVK
  ARM: dts: add support for Laird WB45N cpu module and DVK
  ARM: dts: at91: add labels to soc dtsi for derivative boards
  dt-bindings: add laird and giantec vendor prefix
  ARM: dts: fix PMC compatible
  ARM: at91: fix USB clock detection handling
  dt-bindings: clk: at91: Document all the PMC compatibles
  dt-bindings: arm: remove PMC bindings
Signed-off-by: Olof Johansson <olof@lixom.net>

The OPP properties, like "operating-points", should either be present
for all the CPUs of a cluster or none. If these are present only for a
subset of CPUs of a cluster then things will start falling apart as soon
as the CPUs are brought online in a different order. For example, this
will happen because the operating system looks for such properties in
the CPU node it is trying to bring up, so that it can create an OPP
table.

Add such missing properties.

Fix other missing properties (clocks, clock latency) as well to
make it all work.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

ARM64: DT: Hisilicon SoC DT updates for 4.19v2

- Tidy up MMC properties for hi3660
- Remove keep-power-in-suspend on hikey and hikey960 to
  avoid keeping wifi power during suspend and let the
  user enable it if required
- Update idle states for hikey960
- Add missing cooling device properties for cpus on hi6220

* tag 'hisi-arm64-dt-for-4.19v2' of git://github.com/hisilicon/linux-hisi:
  arm64: dts: hisilicon: Add missing cooling device properties for CPUs
  arm64: hikey960: update idle-states
  arm64: dts: hikey: Remove keep-power-in-suspend property
  arm64: dts: hikey960: Remove keep-power-in-suspend property
  arm64: dts: hikey960: Clean up MMC properties and move to proper file
  arm64: dts: hikey960: Remove deprecated MMC properties
Signed-off-by: Olof Johansson <olof@lixom.net>

ARM: dts: zynq: DT changes for v4.19

- Add Z-turn board
- Add mmc aliases
- Fix model information
- Sort out documentatio
- Update Zybo Z7
- Fix gpio-keys

* tag 'zynq-dt-for-v4.19-v2' of https://github.com/Xilinx/linux-xlnx:
  ARM: dts: zynq: Remove #address/#size-cells from gpio-keys
  ARM: dts: zynq: Add LEDs to the Zybo Z7 board
  ARM: dts: zynq: Use gpio constants for the Zybo Z7 board
  ARM: dts: zynq: Fix memory size on the Zybo Z7 board
  dt-bindings: xilinx: zynq: Add missing boards
  dt-bindings: xilinx: zynq: Move Paralella board to Xilinx
  dt-bindings: xilinx: zynq: Sort entries alphabetically
  dt-bindings: xilinx: zynq: Improve boards description
  ARM: dts: zynq: correct and improve the model property of dt files
  ARM: dts: zynq: Set correct manufacturer for ZedBoard and MicroZed boards
  ARM: dts: zynq: Add mmc alias for zc702/zc706/zed/zybo
  ARM: dts: zynq: Add support for Z-turn board
Signed-off-by: Olof Johansson <olof@lixom.net>

arm: dts: zynqmp: DT changes for v4.19

- Use serdev for BT in zcu100
- Remove ep108
- Fix gpio-keys binding
- Add suport for Ultra96

* tag 'zynqmp-dt-for-v4.19-v2' of https://github.com/Xilinx/linux-xlnx:
  arm64: dts: zynqmp: Add support for Avnet Ultra96 rev1 board
  arm64: dts: zynqmp: Remove #address/#size-cells from gpio-keys
  arm64: dts: zynqmp: Remove ep108 board
  arm64: dts: zynqmp: Use serdev for zcu100 BT
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'uniphier-dt64-v4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier into next/dt

UniPhier ARM64 SoC DT updates for v4.19

- Add missing #cooling-cells properties

- Add hp-det-gpio property to detect headphone via GPIO

* tag 'uniphier-dt64-v4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier:
  arm64: dts: uniphier: add headphone detect gpio for LD11 global board
  arm64: dts: uniphier: add headphone detect gpio for LD20 global board
  arm64: dts: uniphier: Add missing cooling device properties for CPUs
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'uniphier-dt-v4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier into next/dt

UniPhier ARM SoC DT updates for v4.19

- Add missing #cooling-cells properties

* tag 'uniphier-dt-v4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier:
  ARM: dts: uniphier: Add missing cooling device properties for CPUs
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'omap-for-v4.19/dt-pt2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt

Few more beaglebone variants for v4.19 merge window

This adds dts files for two new beaglebone variants for
Octavo Systems OSD3358-SM-RED and Sancloud am335x-sancloud-bbe.

* tag 'omap-for-v4.19/dt-pt2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: dts: am335x: add am335x-sancloud-bbe board support
  dt-bindings: Add vendor prefix for Sancloud
  ARM: dts: Add DT support for Octavo Systems OSD3358-SM-RED based on TI AM335x
Signed-off-by: Olof Johansson <olof@lixom.net>

The OPP properties, like "operating-points", should either be present
for all the CPUs of a cluster or none. If these are present only for a
subset of CPUs of a cluster then things will start falling apart as soon
as the CPUs are brought online in a different order. For example, this
will happen because the operating system looks for such properties in
the CPU node it is trying to bring up, so that it can create an OPP
table.

Add such missing properties.

Fix other missing property (clock latency) as well to make it all
work.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>

Current LED trigger, 'bt', is not known/used by any existing driver.
Fix this by renaming it to 'bluetooth-power' trigger which is
controlled by the Bluetooth subsystem.

Fixes: 9943230c ("arm64: dts: qcom: Add apq8016-sbc board LED's related device nodes")
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>

In commit 8e4947ee477d ("arm64: dts: qcom: sdm845: Add I2C, SPI, and
UART9 nodes") I accidentally forgot to add the line:

  status = "disabled";

to qupv3_id_0 to match qupv3_id_1.  Add it now.  NOTE: right now the
only sdm845 board with a device tree in mainline is MTP and that board
currently doesn't have any peripherals under qupv3_id_0.  If any board
was currently using peripherals under qupv3_id_0 then that board would
need to add this snippet to their board dts file:

  &qupv3_id_0 {
     status = "okay";
  };
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>

Drop legacy suffix for clocks used by MSM DRM driver.

The _clk suffix has been deprecated since commit 20c3bb80235 ("drm/msm:
drop _clk suffix from clk names").

Fixes: 720c3bb8 (drm/msm: drop _clk suffix from clk names)

The following warnings during boot have been seen since the referenced
fixes commit:

msm_dsi_phy 1a98300.dsi-phy: Using legacy clk name binding.  Use "iface" instead of "iface_clk"
msm 1a00000.mdss: Using legacy clk name binding.  Use "iface" instead of "iface_clk"
msm 1a00000.mdss: Using legacy clk name binding.  Use "bus" instead of "bus_clk"
msm 1a00000.mdss: Using legacy clk name binding.  Use "vsync" instead of "vsync_clk"
msm_mdp 1a01000.mdp: Using legacy clk name binding.  Use "bus" instead of "bus_clk"
msm_mdp 1a01000.mdp: Using legacy clk name binding.  Use "iface" instead of "iface_clk"
msm_mdp 1a01000.mdp: Using legacy clk name binding.  Use "core" instead of "core_clk"
msm_mdp 1a01000.mdp: Using legacy clk name binding.  Use "vsync" instead of "vsync_clk"
msm_dsi 1a98000.dsi: Using legacy clk name binding.  Use "mdp_core" instead of "mdp_core_clk"
msm_dsi 1a98000.dsi: Using legacy clk name binding.  Use "iface" instead of "iface_clk"
msm_dsi 1a98000.dsi: Using legacy clk name binding.  Use "bus" instead of "bus_clk"
msm_dsi 1a98000.dsi: Using legacy clk name binding.  Use "byte" instead of "byte_clk"
msm_dsi 1a98000.dsi: Using legacy clk name binding.  Use "pixel" instead of "pixel_clk"
msm_dsi 1a98000.dsi: Using legacy clk name binding.  Use "core" instead of "core_clk"
Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
Reviewed-by: Nicolas Dechesne <nicolas.dechesne@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>

The kernel would not boot on the hammerhead hardware due to the
following error:

mmc0: Timeout waiting for hardware interrupt.
mmc0: sdhci: ============ SDHCI REGISTER DUMP ===========
mmc0: sdhci: Sys addr:  0x00000200 | Version:  0x00003802
mmc0: sdhci: Blk size:  0x00000200 | Blk cnt:  0x00000200
mmc0: sdhci: Argument:  0x00000000 | Trn mode: 0x00000023
mmc0: sdhci: Present:   0x03e80000 | Host ctl: 0x00000034
mmc0: sdhci: Power:     0x00000001 | Blk gap:  0x00000000
mmc0: sdhci: Wake-up:   0x00000000 | Clock:    0x00000007
mmc0: sdhci: Timeout:   0x0000000e | Int stat: 0x00000000
mmc0: sdhci: Int enab:  0x02ff900b | Sig enab: 0x02ff100b
mmc0: sdhci: AC12 err:  0x00000000 | Slot int: 0x00000000
mmc0: sdhci: Caps:      0x642dc8b2 | Caps_1:   0x00008007
mmc0: sdhci: Cmd:       0x00000c1b | Max curr: 0x00000000
mmc0: sdhci: Resp[0]:   0x00000c00 | Resp[1]:  0x00000000
mmc0: sdhci: Resp[2]:   0x00000000 | Resp[3]:  0x00000000
mmc0: sdhci: Host ctl2: 0x00000008
mmc0: sdhci: ADMA Err:  0x00000000 | ADMA Ptr: 0x70040220
mmc0: sdhci: ============================================
mmc0: Card stuck in wrong state! mmcblk0 card_busy_detect status: 0xe00
mmc0: cache flush error -110
mmc0: Reset 0x1 never completed.

This patch increases the load on l20 to 0.2 amps for the sdhci
and allows the device to boot normally.
Signed-off-by: Bhushan Shah <bshah@kde.org>
Signed-off-by: Brian Masney <masneyb@onstation.org>
Suggested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>

Fix all nodes to use proper GIC_* macros for the interrupt type and the
interrupt trigger settings to avoid the boot warnings.
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Tested-by: Abhishek Sahu <absahu@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>

Add gpio-line-names property for Dragonboard820c based on APQ8096 SoC.
There are 4 gpio-controllers present on this board, including the
APQ8096 SoC, PM8994 (GPIO and MPP) and PMI8994 (GPIO).

Lines names are derived from 96Boards CE Specification 1.0, Appendix
"Expansion Connector Signal Description". Line names for PMI8994 MPP
pins are not added due to the absence of the gpio-controller support.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>

This adds the rpmh-clk node to sdm845 based on the examples in the
bindings.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>

This adds the rpmh-rsc node to sdm845 based on the examples in the
bindings.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Lina Iyer <ilina@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>