This is a quick and dirty patch to add panic_write for NAND flashes. The
patch seems to work OK on my CRIS board running a 2.6.26 kernel with a
ID: 0x20, Chip ID: 0xf1 (ST Micro NAND 128MiB 3,3V 8-bit), and also on a
OpenRD base (Marvell Kirkwood) board with a Toshiba NAND 512MiB 3,3V
8-bit flash with 2.6.32-pre1.
Signed-off-by: Edgar E. Iglesias <edgar@axis.com>
Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Signed-off-by: Mika Korhonen <ext-mika.2.korhonen@nokia.com>
Reviewed-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Add support for multiblock erase command. OneNANDs (excluding Flex-OneNAND)
are capable of simultaneous erase of up to 64 eraseblocks which is much faster.

This changes the erase requests for regions covering multiple eraseblocks
to be performed using multiblock erase.
Signed-off-by: Mika Korhonen <ext-mika.2.korhonen@nokia.com>
Reviewed-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Separate the actual execution of erase to a new function:
onenand_block_by_block_erase(). This is done in preparation for
the multiblock erase support.
Signed-off-by: Mika Korhonen <ext-mika.2.korhonen@nokia.com>
Reviewed-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

This module tests NAND ECC functions.

The test is simple.

1. Create a 256 or 512 bytes block of data filled with random bytes (data)
2. Duplicate the data block and inject single bit error (error_data)
3. Try to correct error_data
4. Compare data and error_data
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Vimal Singh <vimalsingh@ti.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Add __nand_calculate_ecc() which does not take struct mtd_info.
The built-in 256/512 software ECC calculation and correction tester
will use it.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Vimal Singh <vimalsingh@ti.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

What is OTP in OneNAND?
The device includes,
1. one block-sized OTP (One Time Programmable) area and
2. user-controlled 1st block OTP(Block 0)
that can be used to increase system security or to provide
identification capabilities.

What is done?
In OneNAND, one block of the NAND Array is set aside as an OTP
memory area, and 1st Block (Block 0) can be used as OTP area.
This area, available to the user, can be configured and locked
with secured user information. The OTP block can be read,
programmed and locked using the same operations as any other NAND
Flash Array memory block. After issuing an OTP-Lock, OTP block
cannot be erased. OTP block is fully-guaranteed to be a good
block.

Why it is done?
Locking the 1st Block OTP has the effect of a 'Write-protect' to
guard against accidental re-programming of data stored in the 1st
block and OTP Block.

Which problem it solves?
OTP support is provided in the existing implementation of
OneNAND/Flex-OneNAND driver, but it is not working with OneNAND
devices. Have observed the following in current OTP OneNAND Implmentation,
1. DataSheet specific sequence to lock the OTP Area is not followed.
2. Certain functions are quiet generic to cope with OTP specific activity.
This patch re-implements OTP support for OneNAND device.

How it is done?
For all blocks, 8th word is available to the user.
However, in case of OTP Block, 8th word of sector 0, page 0 is reserved as
OTP Locking Bit area. Therefore, in case of OTP Block, user usage on this
area is prohibited. Condition specific values are entered in the 8th word,
sector0, page 0 of the OTP block during the process of issuing an OTP-Lock.
The possible conditions are:
1. Only 1st Block Lock
2. Only OTP Block Lock
3. Lock both the 1st Block and the OTP Block

What Other feature additions have been done in this patch?
This patch adds feature for:
1. Only 1st Block Lock
2. Lock both the 1st Block and the OTP Blocks

Re-implemented OTP support for OneNAND
Added following features to OneNAND
	1. Lock only 1st Block in OneNAND
	2. Lock BOTH 1st Block and OTP Block in OneNAND

[comments were slightly tweaked by Artem]
Signed-off-by: Amul Kumar Saha <amul.saha@samsung.com>
Reviewed-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Use hweight_long instead of Brian Kernighan's/Peter Wegner's method
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Commit 4b56ffca ("mtd: Fix kernel NULL
pointer dereference in physmap.c") introduced a couple of bugs.

It neglected to run the loop of map_destroy() calls in
physmap_flash_remove(), if !info->cmtd, which would happen if that
function was called to clean up errors during probe.

It also failed to compile if CONFIG_MTD_PARTITIONS was not defined.
Reported-By: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

This reverts commit 71b7d0d9.

The problem which that commit attempted to fix was a bootloader issue,
which had been misunderstood. The 'fix' causes lots of false bad blocks
for existing users with sane firmware.

Thanks to Mathieu Berland for diagnosing the problem coherently.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

In register_mtd_blktrans(), the symbol 'ret' is already declared
as an int at the start of the function.  The inner loop declaration
is unnecessary.  Quiets the following sparse warning:

  warning: symbol 'ret' shadows an earlier one
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Signed-off-by: Leo Hao Chen <leochen@broadcom.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

During the probe for physmap platform flash devices there are a
number error exit conditions that all do a goto err_out which
then calls physmap_flash_remove().  In that function one of the
cleanup steps is:

#ifdef CONFIG_MTD_CONCAT
	if (info->cmtd != info->mtd[0])
		mtd_concat_destroy(info->cmtd);
#endif

This test will succeed since info->cmtd == NULL and info->mtd[0] is
valid.

Fix this by exiting the remove function when info->cmtd == NULL.

Also, cleanup the #ifdef CONFIG_MTD_PARTITIONS stuff by using
mtd_has_partitions().
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Add a request_mem_region() before doing the ioremap().  Also, use the
resource_size macro instead of doing the end - start + 1 calc by hand.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Convert the (broken) pcmciamtd driver to use the new CIS helpers.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

This driver seems to be obsolete and broken for a long time.
It depends on CONFIG_IPAQ_HANDHELD that simply doesn't exists
anywhere in kernel. Also, it seems that none of machines it
claims to support have any use of it:
 SA11xx-based iPAQs (h3100/h3600) use sa1100-flash
 iPAQ h5000 uses physmap-flash
 Jornada 720 uses sa1100-flash
 Jornada 560 and iPAQ h1910 are not in mainline
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Fix a potential memory leak in mtd_dataflash driver.

The private data that is allocated when registering a DataFlash
device with the MTD subsystem is not released if an error occurs
when add_mtd_partitions() or add_mtd_device() is called.  Fix this
by adding an error path.  The memory is already released during a
remove.

Also, add a dev_set_drvdata(&spi->dev, NULL) before the kfree() so
that the spi device does not reference invalid data.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

- Remove unnecessary memset for bbt
  All entries will be initialized at a few lines below
- Remove unnecessary initialization for mtd->erasesize
- Use write_whole_device()
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Commit f0b1e589 changed sa1100_mtd_probe from __init to __devinit,
but missed to correct sa1100_setup_mtd definition accordingly, which
causes following warning:

WARNING: vmlinux.o(.devinit.text+0xf4): Section mismatch in reference from
 the function sa1100_mtd_probe() to the function .init.text:sa1100_setup_mtd()
The function __devinit sa1100_mtd_probe() references
a function __init sa1100_setup_mtd().
If sa1100_setup_mtd is only used by sa1100_mtd_probe then
annotate sa1100_setup_mtd with a matching annotation.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

The function mxcnd_remove is used only wrapped by __exit_p so define it
using __exit.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Vladimir Barinov <vova.barinov@gmail.com>
Cc: Vladimir Barinov <vbarinov@embeddedalley.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Unused variable "eccpos" removed from atmel_nand driver.
Signed-off-by: Claudio Scordino <claudio@evidence.eu.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

This patch resolves all the prints present in onenand_base.c
Primarily, it replaces the hard-coded function names in the prints,
and makes use of __func__.
Signed-off-by: Amul Kumar Saha <amul.saha@samsung.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Correct typo to use mask_ale from platform data when set to non-zero.
Signed-off-by: Hemant Pedanekar <hemantp@ti.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

drivers/mtd/maps/sa1100-flash.c: In function 'sa1100_probe_subdev':
drivers/mtd/maps/sa1100-flash.c:214: warning: format '%d' expects type 'int', but argument 3 has type 'uint64_t'
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

This enables the onenand with the new platform device name.
Moreover, it fixes a related typo that doesn't deserve a
separate patch.
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

nand.h, onenand.h and flashchip.h defined enumeration types
for chip status using the same symbolic names. This prevented
a board file to include more than one of them. In particular,
no nand and onenand platform devices could live in the same file.
This patch augments flashchip.h with a few status values in order
to cover all cases, so nand.h and onenand.h can use flstate_t
without declaring their own status enum.
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

This consolidates common code in nand.h and bbm.h. The
comments and data structures were the same, this keeps
the comment from nand.h as it fits 80 columns, while the one
in bbm.h did not.
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

The SST SPI flashes is like Atmel SPI flashes in that the software
protection bits are set by default at power up, so clear them at init
time.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

The driver requires gpio functionality, so make sure we depend on that in
the Kconfig menu.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Now that there are linux/ versions of gpio.h and io.h, include those
rather than hitting the asm/ versions.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Fixed following htmldocs warnings:

  DOCPROC Documentation/DocBook/mtdnand.xml
  Warning(drivers/mtd/nand/nand_base.c:769): No description found for parameter 'page'
  Warning(drivers/mtd/nand/nand_base.c:785): No description found for parameter 'page'
  Warning(drivers/mtd/nand/nand_base.c:824): No description found for parameter 'page'
  Warning(drivers/mtd/nand/nand_base.c:947): No description found for parameter 'page'
  Warning(drivers/mtd/nand/nand_base.c:996): No description found for parameter 'page'
  Warning(drivers/mtd/nand/nand_base.c:1040): No description found for parameter 'page'
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

* git://git.infradead.org/mtd-2.6: (58 commits)
  mtd: jedec_probe: add PSD4256G6V id
  mtd: OneNand support for Nomadik 8815 SoC (on NHK8815 board)
  mtd: nand: driver for Nomadik 8815 SoC (on NHK8815 board)
  m25p80: Add Spansion S25FL129P serial flashes
  jffs2: Use SLAB_HWCACHE_ALIGN for jffs2_raw_{dirent,inode} slabs
  mtd: sh_flctl: register sh_flctl using platform_driver_probe()
  mtd: nand: txx9ndfmc: transfer 512 byte at a time if possible
  mtd: nand: fix tmio_nand ecc correction
  mtd: nand: add __nand_correct_data helper function
  mtd: cfi_cmdset_0002: add 0xFF intolerance for M29W128G
  mtd: inftl: fix fold chain block number
  mtd: jedec: fix compilation problem with I28F640C3B definition
  mtd: nand: fix ECC Correction bug for SMC ordering for NDFC driver
  mtd: ofpart: Check availability of reg property instead of name property
  driver/Makefile: Initialize "mtd" and "spi" before "net"
  mtd: omap: adding DMA mode support in nand prefetch/post-write
  mtd: omap: add support for nand prefetch-read and post-write
  mtd: add nand support for w90p910 (v2)
  mtd: maps: add mtd-ram support to physmap_of
  mtd: pxa3xx_nand: add single-bit error corrections reporting
  ...

* 'vgaarb-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
  vgaarb: make client interface config invariant.

* git://git.infradead.org/iommu-2.6: (23 commits)
  intel-iommu: Disable PMRs after we enable translation, not before
  intel-iommu: Kill DMAR_BROKEN_GFX_WA option.
  intel-iommu: Fix integer wrap on 32 bit kernels
  intel-iommu: Fix integer overflow in dma_pte_{clear_range,free_pagetable}()
  intel-iommu: Limit DOMAIN_MAX_PFN to fit in an 'unsigned long'
  intel-iommu: Fix kernel hang if interrupt remapping disabled in BIOS
  intel-iommu: Disallow interrupt remapping if not all ioapics covered
  intel-iommu: include linux/dmi.h to use dmi_ routines
  pci/dmar: correct off-by-one error in dmar_fault()
  intel-iommu: Cope with yet another BIOS screwup causing crashes
  intel-iommu: iommu init error path bug fixes
  intel-iommu: Mark functions with __init
  USB: Work around BIOS bugs by quiescing USB controllers earlier
  ia64: IOMMU passthrough mode shouldn't trigger swiotlb init
  intel-iommu: make domain_add_dev_info() call domain_context_mapping()
  intel-iommu: Unify hardware and software passthrough support
  intel-iommu: Cope with broken HP DC7900 BIOS
  iommu=pt is a valid early param
  intel-iommu: double kfree()
  intel-iommu: Kill pointless intel_unmap_single() function
  ...

Fixed up trivial include lines conflict in drivers/pci/intel-iommu.c

Impact: cleanup

No need for redeclaration.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6: (41 commits)
  regulator: Add some brief design documentation
  regulator: fix voltage range in da9034 ldo12
  regulator/driver: be more specific in nanodoc for is_enabled
  regulator/lp3971: drop unnecessary initialization
  regulator: drop 'default n'
  regulator: fix typos
  regulator: fix calculation of voltage range in da9034_set_ldo12_voltage()
  regulator: update a filename in documentation
  drivers/regulator/Kconfig: fix typo (s/Usersapce/Userspace/) in REGULATOR_USERSPACE_CONSUMER description
  REGULATOR Handle positive returncode from enable
  regulator: tps650xx - build fixes for x86_64
  Fix some regulator documentation
  Regulator: Adding TPS65023 and TPS6507x in Kconfig and Makefile
  Regulator: Add TPS6507x regulator driver
  Regulator: Add TPS65023 regulator driver
  regulator: userspace: use sysfs_create_group
  regulator: Add GPIO enable control to fixed voltage regulator driver
  Regulator: Implement list_voltage for pcf50633 regulator driver.
  regulator: regulator_enable() permission checking
  regulator: Push locking for regulator_is_enabled() out
  ...

* 'fix/misc' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
  ALSA: lx6464es - remove unused struct member
  ALSA: lx6464es - cleanup of rmh message bus function
  ALSA: pcm - Simplify snd_pcm_drain() implementation

* 'fix/asoc' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
  ASoC: wm8753: fix mapping when MONOMIX is set to Stereo
  ASoC: some minor changes for AD1836 and AD1938 codec drivers
  ASoC: DaVinci: Fixes to McASP configuration
  ASoC: Blackfin I2S: fix resuming when device hasn't been used
  ASoC: Blackfin I2S: add lost platform_device parameter to resume function
  ASoC: fix typos in Blackfin headers
  ASoC: bf5xx-sport: the irq save/restore funcs take an unsigned long
  ASoC: Blackfin AC97: add a few missing multichannel define handling