Add a function which indicates our intention to enable or disable a particular
Tx queue. Also add a function to notify the device's Tx unit that we're about
to enable or disable a Tx queue.

Change-ID: I6adf3cbb5bb3e3c984d1ec969e06577c19ef296d
Signed-off-by: Matt Jared <matthew.a.jared@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

B0 Si blocks AQ registers when in Blank Flash mode - write is dropped,
read gives 0xDEADBEEF. Introduce a simple check for a correct value in one
of the AQ registers to be sure that AQ was configured correctly.
Without this check we get into an endless loop while trying to send
GetVersion AQ cmd.

Change-ID: I00102b8c5fa6c16d14289be677aafadf87f10f0d
Signed-off-by: Kamil Krawczyk <kamil.krawczyk@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Depending on the timing of what the PF driver is doing, it make take a
few tries before the VF driver is able to communicate with the PF driver
on init or reset recovery. In order to prevent confusion, make the most
common messages less scary by lowering them to a less terrifying log
level and indicate that the driver will retry.

Change-ID: I1ec22aa59a68f4469aabe14775a1bfc1ab4b7f2f
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The driver and hardware are not expected to work correctly
with revision_id 0 hardware.  Don't prevent the user from
using it, but be sure to print a warning.

Change-ID: I3712d34752bfad458078a5f35dfd0aa0ae9fd20e
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Print the VEB statistics in the ethtool stats output.

Change-ID: Ic93d4c3922345c43e4cfd7f7e7a906844dd2f49f
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

When the VEB is created for the basic LAN device and its VSIs, we need to
set the tracking lan_veb index for later use.

Change-ID: I66bb74993bbda3621ca557437cb4b3517f9b315b
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

To avoid the confusion of having two variables, shrink the function to
only use the parameter variable for looping.

Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Conflicts:
	drivers/net/xen-netback/netback.c
	net/core/filter.c

A filter bug fix overlapped some cleanups and a conversion
over to some new insn generation macros.

A xen-netback bug fix overlapped the addition of multi-queue
support.
Signed-off-by: David S. Miller <davem@davemloft.net>

BPF classic->internal converter broke SKF_AD_PKTTYPE extension, since
pkt_type_offset() was failing to find skb->pkt_type field which is defined as:
__u8 pkt_type:3,
     fclone:2,
     ipvs_property:1,
     peeked:1,
     nf_trace:1;

Fix it by searching for 3 most significant bits and shift them by 5 at run-time

Fixes: bd4cf0ed ("net: filter: rework/optimize internal BPF interpreter's instruction set")
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Tested-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This commit fixes the following sparse warning:

drivers/net/phy/fixed.c:207
    - warning: symbol 'fixed_phy_del' was not declared.
      Should it be static?

by adding symbol definition to the phy_fixed.h API file. It is ok to do
because the function in question is an exported symbol.
Signed-off-by: Konrad Zapalowicz <bergo.torino@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Florian Fainelli says:

====================
net: systemport: misc fixes

This patch series contains some misc fixes for the SYSTEMPORT driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The SYSTEMPORT driver uses libphy to determine the carrier state, so
make sure we start with a carrier off until libphy has completed the
link training process.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The comment about how the hardware prepends 2bytes to align the IP
header on a 4-byte boundary was not correct, fix that.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We were missing an and comparison with status to check whether
RX_STATUS_OVFLOW is asserted or not in the per-packet status word, fix
that.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Our transmit locking scheme did not account for the TX ring full
interrupt. If a TX ring full interrupt fires while we are attempting to
transmit, we will cause a deadlock to occur. Fix this by making sure
that we properly disable interrupts while acquiring the spinlock.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
Netfilter/nf_tables fixes for net-next

This patchset contains fixes for recent updates available in your
net-next, they are:

1) Fix double memory allocation for accounting objects that results
   in a leak, this slipped through with the new quota extension,
   patch from Mathieu Poirier.

2) Fix broken ordering when adding set element transactions.

3) Make sure that objects are released in reverse order in the abort
   path, to avoid possible use-after-free when accessing dependencies.

4) Allow to delete several objects (as long as dependencies are
   fulfilled) by using one batch. This includes changes in the use
   counter semantics of the nf_tables objects.

5) Fix illegal sleeping allocation from rcu callback.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Tom Lendacky says:

====================
amd-xgbe: AMD 10Gb Ethernet driver

The following series implements support for the new AMD 10Gb Ethernet
driver (amd-xgbe).  It includes the 10Gb Ethernet driver as well as
a 10Gb Ethernet PHY driver.

This patch series is based on net-next.

Changes in V3:
  - Add OF dependency to the phylib driver configuration
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds the maintainer information for the AMD 10GbE
platform driver.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch provides the Kconfig and Makefile changes needed
to configure and build the AMD 10GbE platform driver and the
AMD 10GbE phylib driver.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch provides the initial phylib driver in support
of the AMD 10GbE device.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch provides the initial platform driver for the AMD
10GbE device.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch provides the documentation of the device bindings
for the AMD 10GbE platform driver.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

br_manage_promisc() incorrectly expects br_auto_port() to return only 0
or 1, while it actually returns flags, i.e., a subset of BR_AUTO_MASK.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/ethernet/amd/hplance.h:
 #define HPLANCE_MEMOFF 0x8000   /* struct lance_init_block */
 #define HPLANCE_NVRAMOFF 0xC008 /* etheraddress as one *nibble* per byte */

The offset of RAM start is 0x8000, the offset of RAM end is 0xC008,
so the RAM size is 16392 bytes.
Signed-off-by: Amos Kong <akong@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The order of ram pages is 3, so the ram size is 2^3 * 4K = 32K.
Signed-off-by: Amos Kong <akong@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Andrew Ruder says:

====================
miscellaneous dm9000 driver fixes

This is a collection of changes discovered while bringing a PXA270 based board
(Arcom ZEUS) with a Davicom DM9000A/B up to a more recent kernel (from 2.6.xx).
This addresses all of my earlier issues (August 2013) listed here:

http://marc.info/?l=linux-netdev&m=137598605603324&w=2
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

On the DM9000B, dm9000_msleep() is called during the dm9000_timeout()
routine.  Since dm9000_timeout() holds the main spinlock through the
entire routine, mdelay() needs to be used rather than msleep().
Furthermore, the mutex_lock()/mutex_unlock() should be avoided so as to
not sleep with spinlocks held.
Signed-off-by: Andrew Ruder <andrew.ruder@elecsyscorp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

On the DM9000A/DM9000B force the initial check of the link status.  The
DM9000A/B has a link status changed event and this interrupt bit isn't
always set out of reset when a cable is plugged in.  This results in the
driver not seeing the cable attached link status until the cable is
removed and plugged in again.
Signed-off-by: Andrew Ruder <andrew.ruder@elecsyscorp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since dm9000_interrupt() is already reading/clearing every set bit in
DM9000_ISR, this additional clear in dm9000_rx() (which is only called
by dm9000_interrupt()) is unnecessary and can be removed.
Signed-off-by: Andrew Ruder <andrew.ruder@elecsyscorp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

DM9000 uses level-triggered interrupts.  Some systems (PXA270) only
support edge-triggered interrupts on GPIOs.  Some changes are necessary
to ensure that interrupts are not triggered while the GPIO interrupt is
masked or we will miss the interrupt forever.

* Make some helper functions called dm9000_mask_interrupts() and
  dm9000_unmask_interrupts() for readability.

* dm9000_init_dm9000(): ensure that this function always leaves interrupts
  masked regardless of the state when it entered the function.  This is
  primarily to support the situation in dm9000_open where the logic used
  to go:

    dm9000_open()
        dm9000_init_dm9000()
            unmask interrupts
        request_irq()

  If an interrupt occurred between unmasking the interrupt and
  requesting the irq, it would be missed forever as the edge event would
  never be seen by the GPIO hardware in the PXA270.  This allows us to
  change the logic to:

    dm9000_open()
        dm9000_init_dm9000()
            dm9000_mask_interrupts()
        request_irq()
        dm9000_unmask_interrupts()

* dm9000_timeout(), dm9000_drv_resume(): Add the missing
  dm9000_unmask_interrupts() now required by the change above.

* dm9000_shutdown(): Use mask helper function

* dm9000_interrupt(): Use mask/unmask helper functions
Signed-off-by: Andrew Ruder <andrew.ruder@elecsyscorp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

* Change a hard-coded 0x3 to NCR_RST | NCR_MAC_LBK in dm9000_reset

* Every single place where dm9000_init_dm9000 was ran, a dm9000_reset
  was called immediately before-hand.  Bring dm9000_reset into
  dm9000_init_dm9000.

* The following commit updated the dm9000_probe reset routine to use NCR_RST
  | NCR_MAC_LBK:

    6741f40 DM9000B: driver initialization upgrade

  and a later commit added a bug-fix to always reset the chip twice:

    09ee9f87 dm9000: Implement full reset of DM9000 network device

  Unfortunately, since the changes in 6741f40 were made by replacing the
  dm9000_probe dm9000_reset with the adjusted iow(), the changes in
  09ee9f87 were not incorporated into the dm9000_probe reset.
  Furthermore, it bypassed the requisite reset-delay causing some boards
  to get at least one "read wrong id ..." dev_err message during
  dm9000_probe.
Signed-off-by: Andrew Ruder <andrew.ruder@elecsyscorp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The DM9000 supports both active high interrupts and active low interrupts.
This is configured via the attached EEPROM.  In the device-tree case, make sure
that the DM9000 driver passes the correct flags to request_irq.
Signed-off-by: Andrew Ruder <andrew.ruder@elecsyscorp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A recent commit (a02eb4 "xen-netback: worse-case estimate in xenvif_rx_action is
underestimating") capped the slot estimation to MAX_SKB_FRAGS, but that triggers
the next BUG_ON a few lines down, as the packet consumes more slots than
estimated.
This patch introduces full_coalesce on the skb callback buffer, which is used in
start_new_rx_buffer() to decide whether netback needs coalescing more
aggresively. By doing that, no packet should need more than
(XEN_NETIF_MAX_TX_SIZE + 1) / PAGE_SIZE data slots (excluding the optional GSO
slot, it doesn't carry data, therefore irrelevant in this case), as the provided
buffers are fully utilized.
Signed-off-by: Zoltan Kiss <zoltan.kiss@citrix.com>
Cc: Paul Durrant <paul.durrant@citrix.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Reviewed-by: Paul Durrant <paul.durrant@gmail.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

o Uninitialzed fields in mailbox command structure
  caused commands to time out randomly due to garbage
  values so initialize it to zero.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If an MPLS packet requires segmentation then use mpls_features
to determine if the software implementation should be used.

As no driver advertises MPLS GSO segmentation this will always be
the case.

I had not noticed that this was necessary before as software MPLS GSO
segmentation was already being used in my test environment. I believe that
the reason for that is the skbs in question always had fragments and the
driver I used does not advertise NETIF_F_FRAGLIST (which seems to be the
case for most drivers). Thus software segmentation was activated by
skb_gso_ok().

This introduces the overhead of an extra call to skb_network_protocol()
in the case where where CONFIG_NET_MPLS_GSO is set and
skb->ip_summed == CHECKSUM_NONE.

Thanks to Jesse Gross for prompting me to investigate this.
Signed-off-by: Simon Horman <horms@verge.net.au>
Acked-by: YAMAMOTO Takashi <yamamoto@valinux.co.jp>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Quoting David Miller:
"At the moment you call register_netdev() the device is visible, notifications
are sent to userspace, and userland tools can try to bring the interface up
and see the incorrect link state, before you do the netif_carrier_off().

Said another way, between the register_netdev() and netif_carrier_off() call,
userspace can see the device in an inconsistent state."

So call netif_carrier_off() prior to register_netdev().
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
Intel Wired LAN Driver Updates 2014-06-05

This series contains updates to i40e and i40evf.

Jesse fixes an issue reported by Dave Jones where a couple of FD checks
ended up using bitwise OR where it should have been bitwise AND.

Neerav removes unused defines and macros for receive LRO.  Fix the driver
from allowing the user to set a larger MTU size that the hardware was
being configured to support.  Refactors send version which moves code in
two places into a small helper function.

Kamil modifies register diagnostics since register ranges can vary among
the different NVMs to avoid false test results.  So now we try to identify
the full range and use it for a register test and if we fail to define the
proper register range, we will only test the first register from that
group.  Then removes the check for large buffer since this was added in the
case this structure changed in the future, since the AQ definition is now
mature enough that this check is no longer necessary.

Mitch fixes i40evf driver to allocate descriptors in groups of 32 since the
hardware requires it.  Also fixes a crash when the ring size changed because
it would change the count before deallocating resources, causing the driver
to either free nonexistent buffers or leak leftover buffers.  Fixed the
driver to notify the VF for all types of resets so the VF can attempt a
graceful reinit.

Shannon refactors stats collection to create a unifying stats update routine
to call the various stat collection routines.  Removes rx_errors and
rx_missed stats since they were removed from the chip design.  Added
missing VSI statistics that the hardware offers but are not apart of the
standard netdev stats.

v2: dropped patch "i40e: Allow disabling of DCB via debugfs" from Neerav
    based on feedback from David Miller.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a couple more statistics that the hardware offers but aren't part
of the standard netdev stats.

Change-ID: I201db2898f2c284aee3d9631470bc5edd349e9a5
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The rx_errors (GLV_REPC) and rx_missed (GLV_RMPC) were removed
from the chip design.

Change-ID: Ifdeb69c90feac64ec95c36d3d32c75e3a06de3b7
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Pull the PF stat collection out of the VSI collection routine, and
add a unifying stats update routine to call the various stat collection
routines.

Change-ID: I224192455bb3a6e5dc0a426935e67dffc123e306
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>