1. 30 Jul, 2014 6 commits
  2. 02 Jul, 2014 3 commits
    • Laurentiu TUDOR's avatar
      powerpc/85xx: drop hypervisor specific board compatibles · cd115477
      Laurentiu TUDOR authored
      They're almost a duplicate of the boards array
      and we can build them at run-time.
      Signed-off-by: default avatarLaurentiu Tudor <Laurentiu.Tudor@freescale.com>
      Signed-off-by: default avatarScott Wood <scottwood@freescale.com>
      cd115477
    • Shengzhou Liu's avatar
      powerpc/fsl-booke: Add initial T208x QDS board support · 4c18be2b
      Shengzhou Liu authored
      Add support for Freescale T2080/T2081 QDS Development System Board.
      
      The T2080QDS Development System is a high-performance computing,
      evaluation, and development platform that supports T2080 QorIQ
      Power Architecture processor, with following major features:
      
      T2080QDS feature overview:
      Processor:
       - T2080 SoC integrating four 64-bit dual-threads e6500 cores up to 1.8GHz
      Memory:
       - Single memory controller capable of supporting DDR3 and DDR3-LP
       - Dual DIMM slots up 2133MT/s with ECC
      Ethernet interfaces:
       - Two 1Gbps RGMII on-board ports
       - Four 10Gbps XFI on-board cages
       - 1Gbps/2.5Gbps SGMII Riser card
       - 10Gbps XAUI Riser card
      Accelerator:
       - DPAA components consist of FMan, BMan, QMan, PME, DCE and SEC
      SerDes:
       - 16 lanes up to 10.3125GHz
       - Supports Aurora debug, PEX, SATA, SGMII, sRIO, HiGig, XFI and XAUI
      IFC:
       - 128MB NOR Flash, 512MB NAND Flash, PromJet debug port and FPGA
      eSPI:
       - Three SPI flash (16MB N25Q128A + 8MB EN25S64 + 512KB SST25WF040)
      USB:
       - Two USB2.0 ports with internal PHY (one Type-A + one micro Type-AB)
      PCIE:
       - Four PCI Express controllers (two PCIe 2.0 and two PCIe 3.0, SR-IOV)
      SATA:
       - Two SATA 2.0 ports on-board
      SRIO:
       - Two Serial RapidIO 2.0 ports up to 5 GHz
      eSDHC:
       - Supports SD/MMC/eMMC Card
      DMA:
       - Three 8-channels DMA controllers
      I2C:
       - Four I2C controllers.
      UART:
       - Dual 4-pins UART serial ports
      System Logic:
       - QIXIS-II FPGA system controll
      
      T2081QDS board shares the same PCB with T1040QDS with some differences.
      Signed-off-by: default avatarShengzhou Liu <Shengzhou.Liu@freescale.com>
      Signed-off-by: default avatarScott Wood <scottwood@freescale.com>
      4c18be2b
    • Shengzhou Liu's avatar
      powerpc/fsl-booke: Add support for T2080/T2081 SoC · 1d8de8fc
      Shengzhou Liu authored
      The T2080 QorIQ multicore processor combines four dual-threaded e6500 Power
      Architecture processor cores with high-performance datapath acceleration
      logic and network and peripheral bus interfaces required for networking,
      telecom/datacom, wireless infrastructure, and mil/aerospace applications.
      
      The T2080 SoC includes the following function and features:
      - Four dual-threaded 64-bit Power architecture e6500 cores, up to 1.8GHz
      - 2MB L2 cache and 512KB CoreNet platform cache (CPC)
      - Hierarchical interconnect fabric
      - One 32-/64-bit DDR3/3L SDRAM memory controllers with ECC and interleaving
      - Data Path Acceleration Architecture (DPAA) incorporating acceleration
      - 16 SerDes lanes up to 10.3125 GHz
      - 8 Ethernet interfaces (multiple 1G/2.5G/10G MACs)
      - High-speed peripheral interfaces
        - Four PCI Express controllers (two PCIe 2.0 and two PCIe 3.0)
        - Two Serial RapidIO 2.0 controllers/ports running at up to 5 GHz
      - Additional peripheral interfaces
        - Two serial ATA (SATA 2.0) controllers
        - Two high-speed USB 2.0 controllers with integrated PHY
        - Enhanced secure digital host controller (SD/SDXC/eMMC)
        - Enhanced serial peripheral interface (eSPI)
        - Four I2C controllers
        - Four 2-pin UARTs or two 4-pin UARTs
        - Integrated Flash Controller supporting NAND and NOR flash
      - Three eight-channel DMA engines
      - Support for hardware virtualization and partitioning enforcement
      - QorIQ Platform's Trust Architecture 2.0
      
      T2081 is a reduced personality of T2080 with following difference:
      Feature               T2080 T2081
      1G Ethernet numbers:  8     6
      10G Ethernet numbers: 4     2
      SerDes lanes:         16    8
      Serial RapidIO,RMan:  2     no
      SATA Controller:      2     no
      Aurora:               yes   no
      SoC Package:          896-pins 780-pins
      Signed-off-by: default avatarShengzhou Liu <Shengzhou.Liu@freescale.com>
      [scottwood@freescale.com: added fsl,qoriq-pci-v3.0 for U-Boot compat]
      Signed-off-by: default avatarScott Wood <scottwood@freescale.com>
      1d8de8fc
  3. 25 Jun, 2014 5 commits
  4. 20 Jun, 2014 9 commits
  5. 16 Jun, 2014 5 commits
    • Benjamin Herrenschmidt's avatar
      Revert "offb: Add palette hack for little endian" · 68986c9f
      Benjamin Herrenschmidt authored
      This reverts commit e1edf18b.
      
      This patch was a misguided attempt at fixing offb for LE ppc64
      kernels on BE qemu but is just wrong ... it breaks real LE/LE
      setups, LE with real HW, and existing mixed endian systems
      that did the fight thing with the appropriate device-tree
      property. Bad reviewing on my part, sorry.
      
      The right fix is to either make qemu change its endian when
      the guest changes endian (working on that) or to use the
      existing foreign endian support.
      Signed-off-by: default avatarBenjamin Herrenschmidt <benh@kernel.crashing.org>
      CC: <stable@vger.kernel.org> [v3.13+]
      ---
      68986c9f
    • Linus Torvalds's avatar
      Linux 3.16-rc1 · 7171511e
      Linus Torvalds authored
      7171511e
    • Linus Torvalds's avatar
      Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net · a9be2242
      Linus Torvalds authored
      Pull networking fixes from David Miller:
      
       1) Fix checksumming regressions, from Tom Herbert.
      
       2) Undo unintentional permissions changes for SCTP rto_alpha and
          rto_beta sysfs knobs, from Denial Borkmann.
      
       3) VXLAN, like other IP tunnels, should advertize it's encapsulation
          size using dev->needed_headroom instead of dev->hard_header_len.
          From Cong Wang.
      
      * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
        net: sctp: fix permissions for rto_alpha and rto_beta knobs
        vxlan: Checksum fixes
        net: add skb_pop_rcv_encapsulation
        udp: call __skb_checksum_complete when doing full checksum
        net: Fix save software checksum complete
        net: Fix GSO constants to match NETIF flags
        udp: ipv4: do not waste time in __udp4_lib_mcast_demux_lookup
        vxlan: use dev->needed_headroom instead of dev->hard_header_len
        MAINTAINERS: update cxgb4 maintainer
      a9be2242
    • Linus Torvalds's avatar
      Merge tag 'clk-for-linus-3.16-part2' of git://git.linaro.org/people/mike.turquette/linux · dd1845af
      Linus Torvalds authored
      Pull more clock framework updates from Mike Turquette:
       "This contains the second half the of the clk changes for 3.16.
      
        They are simply fixes and code refactoring for the OMAP clock drivers.
        The sunxi clock driver changes include splitting out the one
        mega-driver into several smaller pieces and adding support for the A31
        SoC clocks"
      
      * tag 'clk-for-linus-3.16-part2' of git://git.linaro.org/people/mike.turquette/linux: (25 commits)
        clk: sunxi: document PRCM clock compatible strings
        clk: sunxi: add PRCM (Power/Reset/Clock Management) clks support
        clk: sun6i: Protect SDRAM gating bit
        clk: sun6i: Protect CPU clock
        clk: sunxi: Rework clock protection code
        clk: sunxi: Move the GMAC clock to a file of its own
        clk: sunxi: Move the 24M oscillator to a file of its own
        clk: sunxi: Remove calls to clk_put
        clk: sunxi: document new A31 USB clock compatible
        clk: sunxi: Implement A31 USB clock
        ARM: dts: OMAP5/DRA7: use omap5-mpu-dpll-clock capable of dealing with higher frequencies
        CLK: TI: dpll: support OMAP5 MPU DPLL that need special handling for higher frequencies
        ARM: OMAP5+: dpll: support Duty Cycle Correction(DCC)
        CLK: TI: clk-54xx: Set the rate for dpll_abe_m2x2_ck
        CLK: TI: Driver for DRA7 ATL (Audio Tracking Logic)
        dt:/bindings: DRA7 ATL (Audio Tracking Logic) clock bindings
        ARM: dts: dra7xx-clocks: Correct name for atl clkin3 clock
        CLK: TI: gate: add composite interface clock to OMAP2 only build
        ARM: OMAP2: clock: add DT boot support for cpufreq_ck
        CLK: TI: OMAP2: add clock init support
        ...
      dd1845af
    • Linus Torvalds's avatar
      Merge git://git.infradead.org/users/willy/linux-nvme · b55b3902
      Linus Torvalds authored
      Pull NVMe update from Matthew Wilcox:
       "Mostly bugfixes again for the NVMe driver.  I'd like to call out the
        exported tracepoint in the block layer; I believe Keith has cleared
        this with Jens.
      
        We've had a few reports from people who're really pounding on NVMe
        devices at scale, hence the timeout changes (and new module
        parameters), hotplug cpu deadlock, tracepoints, and minor performance
        tweaks"
      
      [ Jens hadn't seen that tracepoint thing, but is ok with it - it will
        end up going away when mq conversion happens ]
      
      * git://git.infradead.org/users/willy/linux-nvme: (22 commits)
        NVMe: Fix START_STOP_UNIT Scsi->NVMe translation.
        NVMe: Use Log Page constants in SCSI emulation
        NVMe: Define Log Page constants
        NVMe: Fix hot cpu notification dead lock
        NVMe: Rename io_timeout to nvme_io_timeout
        NVMe: Use last bytes of f/w rev SCSI Inquiry
        NVMe: Adhere to request queue block accounting enable/disable
        NVMe: Fix nvme get/put queue semantics
        NVMe: Delete NVME_GET_FEAT_TEMP_THRESH
        NVMe: Make admin timeout a module parameter
        NVMe: Make iod bio timeout a parameter
        NVMe: Prevent possible NULL pointer dereference
        NVMe: Fix the buffer size passed in GetLogPage(CDW10.NUMD)
        NVMe: Update data structures for NVMe 1.2
        NVMe: Enable BUILD_BUG_ON checks
        NVMe: Update namespace and controller identify structures to the 1.1a spec
        NVMe: Flush with data support
        NVMe: Configure support for block flush
        NVMe: Add tracepoints
        NVMe: Protect against badly formatted CQEs
        ...
      b55b3902
  6. 15 Jun, 2014 11 commits
    • Daniel Borkmann's avatar
      net: sctp: fix permissions for rto_alpha and rto_beta knobs · b58537a1
      Daniel Borkmann authored
      Commit 3fd091e7 ("[SCTP]: Remove multiple levels of msecs
      to jiffies conversions.") has silently changed permissions for
      rto_alpha and rto_beta knobs from 0644 to 0444. The purpose of
      this was to discourage users from tweaking rto_alpha and
      rto_beta knobs in production environments since they are key
      to correctly compute rtt/srtt.
      
      RFC4960 under section 6.3.1. RTO Calculation says regarding
      rto_alpha and rto_beta under rule C3 and C4:
      
        [...]
        C3)  When a new RTT measurement R' is made, set
      
             RTTVAR <- (1 - RTO.Beta) * RTTVAR + RTO.Beta * |SRTT - R'|
      
             and
      
             SRTT <- (1 - RTO.Alpha) * SRTT + RTO.Alpha * R'
      
             Note: The value of SRTT used in the update to RTTVAR
             is its value before updating SRTT itself using the
             second assignment. After the computation, update
             RTO <- SRTT + 4 * RTTVAR.
      
        C4)  When data is in flight and when allowed by rule C5
             below, a new RTT measurement MUST be made each round
             trip. Furthermore, new RTT measurements SHOULD be
             made no more than once per round trip for a given
             destination transport address. There are two reasons
             for this recommendation: First, it appears that
             measuring more frequently often does not in practice
             yield any significant benefit [ALLMAN99]; second,
             if measurements are made more often, then the values
             of RTO.Alpha and RTO.Beta in rule C3 above should be
             adjusted so that SRTT and RTTVAR still adjust to
             changes at roughly the same rate (in terms of how many
             round trips it takes them to reflect new values) as
             they would if making only one measurement per
             round-trip and using RTO.Alpha and RTO.Beta as given
             in rule C3. However, the exact nature of these
             adjustments remains a research issue.
        [...]
      
      While it is discouraged to adjust rto_alpha and rto_beta
      and not further specified how to adjust them, the RFC also
      doesn't explicitly forbid it, but rather gives a RECOMMENDED
      default value (rto_alpha=3, rto_beta=2). We have a couple
      of users relying on the old permissions before they got
      changed. That said, if someone really has the urge to adjust
      them, we could allow it with a warning in the log.
      
      Fixes: 3fd091e7 ("[SCTP]: Remove multiple levels of msecs to jiffies conversions.")
      Signed-off-by: default avatarDaniel Borkmann <dborkman@redhat.com>
      Cc: Vlad Yasevich <vyasevich@gmail.com>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      b58537a1
    • David S. Miller's avatar
      Merge branch 'csum_fixes' · e4f7ae93
      David S. Miller authored
      Tom Herbert says:
      
      ====================
      Fixes related to some recent checksum modifications.
      
      - Fix GSO constants to match NETIF flags
      - Fix logic in saving checksum complete in __skb_checksum_complete
      - Call __skb_checksum_complete from UDP if we are checksumming over
        whole packet in order to save checksum.
      - Fixes to VXLAN to work correctly with checksum complete
      ====================
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      e4f7ae93
    • Tom Herbert's avatar
      vxlan: Checksum fixes · f79b064c
      Tom Herbert authored
      Call skb_pop_rcv_encapsulation and postpull_rcsum for the Ethernet
      header to work properly with checksum complete.
      Signed-off-by: default avatarTom Herbert <therbert@google.com>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      f79b064c
    • Tom Herbert's avatar
      net: add skb_pop_rcv_encapsulation · e5eb4e30
      Tom Herbert authored
      This function is used by UDP encapsulation protocols in RX when
      crossing encapsulation boundary. If ip_summed is set to
      CHECKSUM_UNNECESSARY and encapsulation is not set, change to
      CHECKSUM_NONE since the checksum has not been validated within the
      encapsulation. Clears csum_valid by the same rationale.
      Signed-off-by: default avatarTom Herbert <therbert@google.com>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      e5eb4e30
    • Tom Herbert's avatar
      udp: call __skb_checksum_complete when doing full checksum · bbdff225
      Tom Herbert authored
      In __udp_lib_checksum_complete check if checksum is being done over all
      the data (len is equal to skb->len) and if it is call
      __skb_checksum_complete instead of __skb_checksum_complete_head. This
      allows checksum to be saved in checksum complete.
      Signed-off-by: default avatarTom Herbert <therbert@google.com>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      bbdff225
    • Tom Herbert's avatar
      net: Fix save software checksum complete · 46fb51eb
      Tom Herbert authored
      Geert reported issues regarding checksum complete and UDP.
      The logic introduced in commit 7e3cead5
      ("net: Save software checksum complete") is not correct.
      
      This patch:
      1) Restores code in __skb_checksum_complete_header except for setting
         CHECKSUM_UNNECESSARY. This function may be calculating checksum on
         something less than skb->len.
      2) Adds saving checksum to __skb_checksum_complete. The full packet
         checksum 0..skb->len is calculated without adding in pseudo header.
         This value is saved in skb->csum and then the pseudo header is added
         to that to derive the checksum for validation.
      3) In both __skb_checksum_complete_header and __skb_checksum_complete,
         set skb->csum_valid to whether checksum of zero was computed. This
         allows skb_csum_unnecessary to return true without changing to
         CHECKSUM_UNNECESSARY which was done previously.
      4) Copy new csum related bits in __copy_skb_header.
      Reported-by: default avatarGeert Uytterhoeven <geert@linux-m68k.org>
      Signed-off-by: default avatarTom Herbert <therbert@google.com>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      46fb51eb
    • Tom Herbert's avatar
      net: Fix GSO constants to match NETIF flags · 4b28252c
      Tom Herbert authored
      Joseph Gasparakis reported that VXLAN GSO offload stopped working with
      i40e device after recent UDP changes. The problem is that the
      SKB_GSO_* bits are out of sync with the corresponding NETIF flags. This
      patch fixes that. Also, we add BUILD_BUG_ONs in net_gso_ok for several
      GSO constants that were missing to avoid the problem in the future.
      Reported-by: default avatarJoseph Gasparakis <joseph.gasparakis@intel.com>
      Signed-off-by: default avatarTom Herbert <therbert@google.com>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      4b28252c
    • Linus Torvalds's avatar
      Merge tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi · abf04af7
      Linus Torvalds authored
      Pull more SCSI updates from James Bottomley:
       "This is just a couple of drivers (hpsa and lpfc) that got left out for
        further testing in linux-next.  We also have one fix to a prior
        submission (qla2xxx sparse)"
      
      * tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (36 commits)
        qla2xxx: fix sparse warnings introduced by previous target mode t10-dif patch
        lpfc: Update lpfc version to driver version 10.2.8001.0
        lpfc: Fix ExpressLane priority setup
        lpfc: mark old devices as obsolete
        lpfc: Fix for initializing RRQ bitmap
        lpfc: Fix for cleaning up stale ring flag and sp_queue_event entries
        lpfc: Update lpfc version to driver version 10.2.8000.0
        lpfc: Update Copyright on changed files from 8.3.45 patches
        lpfc: Update Copyright on changed files
        lpfc: Fixed locking for scsi task management commands
        lpfc: Convert runtime references to old xlane cfg param to fof cfg param
        lpfc: Fix FW dump using sysfs
        lpfc: Fix SLI4 s abort loop to process all FCP rings and under ring_lock
        lpfc: Fixed kernel panic in lpfc_abort_handler
        lpfc: Fix locking for postbufq when freeing
        lpfc: Fix locking for lpfc_hba_down_post
        lpfc: Fix dynamic transitions of FirstBurst from on to off
        hpsa: fix handling of hpsa_volume_offline return value
        hpsa: return -ENOMEM not -1 on kzalloc failure in hpsa_get_device_id
        hpsa: remove messages about volume status VPD inquiry page not supported
        ...
      abf04af7
    • Linus Torvalds's avatar
      Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs · 16d52ef7
      Linus Torvalds authored
      Pull more btrfs updates from Chris Mason:
       "This has a few fixes since our last pull and a new ioctl for doing
        btree searches from userland.  It's very similar to the existing
        ioctl, but lets us return larger items back down to the app"
      
      * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
        btrfs: fix error handling in create_pending_snapshot
        btrfs: fix use of uninit "ret" in end_extent_writepage()
        btrfs: free ulist in qgroup_shared_accounting() error path
        Btrfs: fix qgroups sanity test crash or hang
        btrfs: prevent RCU warning when dereferencing radix tree slot
        Btrfs: fix unfinished readahead thread for raid5/6 degraded mounting
        btrfs: new ioctl TREE_SEARCH_V2
        btrfs: tree_search, search_ioctl: direct copy to userspace
        btrfs: new function read_extent_buffer_to_user
        btrfs: tree_search, copy_to_sk: return needed size on EOVERFLOW
        btrfs: tree_search, copy_to_sk: return EOVERFLOW for too small buffer
        btrfs: tree_search, search_ioctl: accept varying buffer
        btrfs: tree_search: eliminate redundant nr_items check
      16d52ef7
    • Linus Torvalds's avatar
      Merge git://git.kvack.org/~bcrl/aio-next · a311c480
      Linus Torvalds authored
      Pull aio fix and cleanups from Ben LaHaise:
       "This consists of a couple of code cleanups plus a minor bug fix"
      
      * git://git.kvack.org/~bcrl/aio-next:
        aio: cleanup: flatten kill_ioctx()
        aio: report error from io_destroy() when threads race in io_destroy()
        fs/aio.c: Remove ctx parameter in kiocb_cancel
      a311c480
    • Al Viro's avatar
      fix __swap_writepage() compile failure on old gcc versions · 05064084
      Al Viro authored
      Tetsuo Handa wrote:
       "Commit 62a8067a ("bio_vec-backed iov_iter") introduced an unnamed
        union inside a struct which gcc-4.4.7 cannot handle.  Name the unnamed
         union as u in order to fix build failure"
      
      Let's do this instead: there is only one place in the entire tree that
      steps into this breakage.  Anon structs and unions work in older gcc
      versions; as the matter of fact, we have those in the tree - see e.g.
      struct ieee80211_tx_info in include/net/mac80211.h
      
      What doesn't work is handling their initializers:
      
      struct {
      	int a;
      	union {
      		int b;
      		char c;
      	};
      } x[2] = {{.a = 1, .c = 'a'}, {.a = 0, .b = 1}};
      
      is the obvious syntax for initializer, perfectly fine for C11 and
      handled correctly by gcc-4.7 or later.
      
      Earlier versions, though, break on it - declaration is fine and so's
      access to fields (i.e.  x[0].c = 'a'; would produce the right code), but
      members of the anon structs and unions are not inserted into the right
      namespace.  Tellingly, those older versions will not barf on struct {int
      a; struct {int a;};}; - looks like they just have it hacked up somewhere
      around the handling of .  and -> instead of doing the right thing.
      
      The easiest way to deal with that crap is to turn initialization of
      those fields (in the only place where we have such initializer of
      iov_iter) into plain assignment.
      Reported-by: default avatarTetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
      Reported-by: default avatarRussell King <rmk+kernel@arm.linux.org.uk>
      Signed-off-by: default avatarAl Viro <viro@zeniv.linux.org.uk>
      Signed-off-by: default avatarLinus Torvalds <torvalds@linux-foundation.org>
      05064084
  7. 14 Jun, 2014 1 commit