The USB hub driver's event handler contains a check to catch SuperSpeed
devices that transitioned into the SS.Inactive state and tries to fix
them with a reset. It decides whether to do a plain hub port reset or
call the usb_reset_device() function based on whether there was a device
attached to the port.

However, there are device/hub combinations (found with a JetFlash
Transcend mass storage stick (8564:1000) on the root hub of an Intel
LynxPoint PCH) which can transition to the SS.Inactive state on
disconnect (and stay there long enough for the host to notice). In this
case, above-mentioned reset check will call usb_reset_device() on the
stale device data structure. The kernel will send pointless LPM control
messages to the no longer connected device address and can even cause
several 5 second khubd stalls on some (buggy?) host controllers, before
finally accepting the device's fate amongst a flurry of error messages.

This patch makes the choice of reset dependent on the port status that
has just been read from the hub in addition to the existence of an
in-kernel data structure for the device, and only proceeds with the more
extensive reset if both are valid.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>

RT Systems makes many usb serial cables based on the ftdi_sio driver for
programming various amateur radios.  This patch is a full listing of
their current product offerings and should allow these cables to all
be recognized.
Signed-off-by: Rick Farina (Zero_Chaos) <zerochaos@gentoo.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Using below  configs, the compile will have error:
ERROR: "ehci_init_driver" undefined!

.config:
CONFIG_USB_CHIPIDEA=m
CONFIG_USB_CHIPIDEA_HOST=y
CONFIG_USB_CHIPIDEA_DEBUG=y

The reason is chipidea host uses symbol from ehci, but ehci
is not compiled. Let the chipidea host depend on
ehci even it is built as module.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix the following build warnings on x86:

drivers/usb/chipidea/core.c: In function 'hw_phymode_configure':
drivers/usb/chipidea/core.c:226:3: warning: large integer implicitly truncated to unsigned type [-Woverflow]
drivers/usb/chipidea/core.c:230:3: warning: large integer implicitly truncated to unsigned type [-Woverflow]
drivers/usb/chipidea/core.c:243:3: warning: large integer implicitly truncated to unsigned type [-Woverflow]
drivers/usb/chipidea/core.c:246:3: warning: large integer implicitly truncated to unsigned type [-Woverflow]
Reported-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Merge tag 'fixes-for-v3.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus

Felipe writes:

usb: fixes for v3.11-rc3

Here are some fixes for v3.11-rc3. Mostly related to
the recent conversion to configfs done on the gadget
drivers, but we also have a fix for MUSB resources
on platforms which need 3 resources instead of 2, and
a fix for the sysfs_notify() call on udc-core.c which
was notifying an unexistent file.

The name of udc state attribute file under sysfs is registered as
"state", while usb_gadget_set_state take it as "status" when it's
going to update. This patch fixes the typo.
Signed-off-by: Rong Wang <Rong.Wang@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Cc: <stable@kernel.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>

The compatibility layer which the USBF_PHONET_INCLUDED was a part of
is no longer present - the USBF_PHONET_INCLUDED is not #defined by anyone
anymore, so the ifndef is always true. Removing it.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Fix to return a negative error code from the error handling
case instead of 0, as returned elsewhere in this function.

Introduced by commit 59835a (usb: gadget: multi: use
function framework for ACM.)

Make rndis_do_config() consistent with cdc_do_config() in the way it
handles returning the PTR_ERR(f_acm_*).
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Silence compiler warnings on 64-bit systems introduced by commit
05cf0dec ("USB: mos7840: fix race in led handling") which uses the
usb-serial data pointer to temporarily store the device type during
probe but failed to add the required casts.

[gregkh - change uintptr_t to unsigned long]

Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix race in LED handling introduced by commit 0eafe4de ("USB: serial:
mos7840: add support for MCS7810 devices") which reused the port control
urb for manipulating the LED without making sure that the urb is not
already in use. This could lead to the control urb being manipulated
while in flight.

Fix by adding a dedicated LED urb and ctrlrequest along with a LED-busy
flag to handle concurrency.

Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix race in device-type detection introduced by commit 0eafe4de ("USB:
serial: mos7840: add support for MCS7810 devices") which used a static
variable to hold the device type.

Move type detection to probe and use serial data to store the device
type.

Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix race in mos7840_get_reg which unconditionally manipulated the
control urb (which may already be in use) by adding a control-urb busy
flag.

Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This adds a driver for the Suunto ANT+ USB device, exposing it as a usb
serial device.  This lets the userspace "gant" program to talk to the
device to communicate over the ANT+ protocol to any devices it finds.
Reported-by: Steinar Gunderson <sgunderson@bigfoot.com>
Tested-by: Steinar Gunderson <sgunderson@bigfoot.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Control transfers have both IN and OUT (or SETUP) packets, so when
clearing TT buffers for a control transfer it's necessary to send
two HUB_CLEAR_TT_BUFFER requests to the hub.
Signed-off-by: William Gulland <wgulland@google.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix memory leaks introduced in commits:

40d133d7
usb: gadget: f_ncm: convert to new function interface with backward compatibility

fee562a6
usb: gadget: f_ecm: convert to new function interface with backward compatibility

fcbdf12e
usb: gadget: f_phonet: convert to new function interface with backward compatibility

b29002a1
usb: gadget: f_eem: convert to new function interface with backward compatibility

8cedba7c
usb: gadget: f_subset: convert to new function interface with backward compatibility

f466c635
usb: gadget: f_rndis: convert to new function interface with backward compatibility
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Allocated urbs and buffers were never freed on errors in open.

Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Some (very few) early devices like mine, where not exposting a proper CDC
descriptor. This was fixed with an immediate firmware update from the vendor,
and pre-installed on newer devices.
So actual devices can be driven by cdc_acm.c + cdc_ether.c.
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Speaks AT on interfaces 5 (command & PPP) and 3 (secondary), other
interface protocols are unknown.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Prevent the option driver from binding itself to the QMI/WWAN interface, making
it unusable by the proper driver.
Signed-off-by: enrico Mioso <mrkiko.rs@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix memory leaks introduced in commits:

40d133d7
usb: gadget: f_ncm: convert to new function interface with backward compatibility

fee562a6
usb: gadget: f_ecm: convert to new function interface with backward compatibility

fcbdf12e
usb: gadget: f_phonet: convert to new function interface with backward compatibility

b29002a1
usb: gadget: f_eem: convert to new function interface with backward compatibility

8cedba7c
usb: gadget: f_subset: convert to new function interface with backward compatibility

f466c635
usb: gadget: f_rndis: convert to new function interface with backward compatibility
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Fix bugs introduced in

9c62ce83
usb: gadget: ether: convert to new interface of f_ecm

94b5573e
usb: gadget: ether: convert to new interface of f_eem

8af5232d
usb: gadget: ether: convert to new interface of f_subset

9bd4a10e
usb: gadget: ether: convert to new interface of f_rndis
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Merge tag 'for-usb-linus-2013-07-25' of git://git.kernel.org/pub/scm/linux/kernel/git/sarah/xhci into usb-linus

Sarah writes:

xhci: Bug fixes, now with more tags!

Hi Greg,

Here's five bug fixes for 3.12.

The three patches are marked for stable.  Two fix NULL pointer dereferences.
The third marked for stable suppresses some serious log spam from unnecessary
xHCI driver warnings, whenever an isochronous short packet happens on an xHCI
1.0 host.

The other two patches fix build warnings.

Sarah Sharp

in some cases where device is attched to xhci port and do not responding,
for example ath9k_htc with stalled firmware, kernel will
crash on ring_doorbell_for_active_rings.
This patch check if pointer exist before it is used.

This patch should be backported to kernels as old as 2.6.35, that
contain the commit e9df17eb "USB: xhci:
Correct assumptions about number of rings per endpoint"
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org

Xhci controllers with hci_version > 0.96 gives spurious success
events on short packet completion. During webcam capture the
"ERROR Transfer event TRB DMA ptr not part of current TD" was observed.
The same application works fine with synopsis controllers hci_version 0.96.
The same issue is seen with Intel Pantherpoint xhci controller. So enabling
this quirk in xhci_gen_setup if controller verion is greater than 0.96.
For xhci-pci move the quirk to much generic place xhci_gen_setup.

Note from Sarah:

The xHCI 1.0 spec changed how hardware handles short packets.  The HW
will notify SW of the TRB where the short packet occurred, and it will
also give a successful status for the last TRB in a TD (the one with the
IOC flag set).  On the second successful status, that warning will be
triggered in the driver.

Software is now supposed to not assume the TD is not completed until it
gets that last successful status.  That means we have a slight race
condition, although it should have little practical impact.  This patch
papers over that issue.

It's on my long-term to-do list to fix this race condition, but it is a
much more involved patch that will probably be too big for stable.  This
patch is needed for stable to avoid serious log spam.

This patch should be backported to kernels as old as 3.0, that
contain the commit ad808333 "Intel xhci:
Ignore spurious successful event."

The patch will have to be modified for kernels older than 3.2, since
that kernel added the xhci_gen_setup function for xhci platform devices.
The correct conflict resolution for kernels older than 3.2 is to set
XHCI_SPURIOUS_SUCCESS in xhci_pci_quirks for all xHCI 1.0 hosts.
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org

Fix warning when CONFIG_PCI is not enabled
(from commit 29636578).

drivers/usb/host/pci-quirks.h: warning: its scope is only this definition or declaration, which is probably not what you want [enabled by default]
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Moiz Sonasath <m-sonasath@ti.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>

Resolves the following build warnings:
drivers/usb/host/xhci.c:332:13: warning: 'xhci_msix_sync_irqs' defined but not used [-Wunused-function]
drivers/usb/host/xhci.c:3901:12: warning: 'xhci_change_max_exit_latency' defined but not used [-Wunused-function]

These functions are not always used, and since they're marked static
they will produce build warnings:
- xhci_msix_sync_irqs is only used with CONFIG_PCI.
- xhci_change_max_exit_latency is a little more complicated with
  dependencies on CONFIG_PM and CONFIG_PM_RUNTIME.

Instead of building a bigger maze of ifdefs in this code, I've just
marked both with __maybe_unused.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>

When the host controller fails to respond to an Enable Slot command, and
the host fails to respond to the register write to abort the command
ring, the xHCI driver will assume the host is dead, and call
usb_hc_died().

The USB device's slot_id is still set to zero, and the pointer stored at
xhci->devs[0] will always be NULL.  The call to xhci_check_args in
xhci_free_dev should have caught the NULL virt_dev pointer.

However, xhci_free_dev is designed to free the xhci_virt_device
structures, even if the host is dead, so that we don't leak kernel
memory.  xhci_free_dev checks the return value from the generic
xhci_check_args function.  If the return value is -ENODEV, it carries on
trying to free the virtual device.

The issue is that xhci_check_args looks at the host controller state
before it looks at the xhci_virt_device pointer.  It will return -ENIVAL
because the host is dead, and xhci_free_dev will ignore the return
value, and happily dereference the NULL xhci_virt_device pointer.

The fix is to make sure that xhci_check_args checks the xhci_virt_device
pointer before it checks the host state.

See https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1203453 for
further details.  This patch doesn't solve the underlying issue, but
will ensure we don't see any more NULL pointer dereferences because of
the issue.

This patch should be backported to kernels as old as 3.1, that
contain the commit 7bd89b40 "xhci: Don't
submit commands or URBs to halted hosts."
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: Vincent Thiele <vincentthiele@gmail.com>
Cc: stable@vger.kernel.org

This patch adds support for the ONYX 3G device (version 1) from ALFA
NETWORK.
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The driver failed to take the dynamic ids into account when determining
the device type and therefore all devices were detected as 2-port
devices when using the dynamic-id interface.

Match on the usb-serial-driver field instead of doing redundant id-table
searches.
Reported-by: Anders Hammarquist <iko@iko.pp.se>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Signed-off-by: Bjørn Mork <bjorn@mork.no>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Adding support for D-Link DWM-152/C1 and DWM-156/C1 devices.

DWM-152/C1:
T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  6 Spd=480 MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=07d1 ProdID=3e01 Rev= 0.00
S:  Product=USB Configuration
S:  SerialNumber=1234567890ABCDEF
C:* #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=81(I) Atr=03(Int.) MxPS=  64 Ivl=2ms
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 4 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E:  Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms

DWM-156/C1:
T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  8 Spd=480 MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=07d1 ProdID=3e02 Rev= 0.00
S:  Product=DataCard Device
S:  SerialNumber=1234567890ABCDEF
C:* #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=81(I) Atr=03(Int.) MxPS=  64 Ivl=2ms
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 4 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E:  Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Signed-off-by: Alexandr Ivanov <alexandr.sky@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Set the ehci->resuming flag for the port we receive a remote
wakeup on so that resume signalling can be completed.

Without this, the root hub timer will not fire again to check
if the resume was completed and there will be a never-ending wait on
on the port.

This effect is only observed if the HUB IRQ IN does not come after we
have initiated the port resume.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Added support for MMB Networks and Planet Innovation Ingeni ZigBee USB
devices using customized Silicon Labs' CP210x.c USB to UART bridge
drivers with PIDs: 88A4, 88A5.
Signed-off-by: Sami Rahman <sami.rahman@mmbresearch.com>
Tested-by: Sami Rahman <sami.rahman@mmbresearch.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch adds support for the Schweitzer Engineering Laboratories
C662 USB cable based off the CP210x driver.
Signed-off-by: Barry Grussling <barry@grussling.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch was tested on 3.10.1 kernel.

Same models of Petatel NP10T modems have different device IDs.
Unfortunately they have no additional revision information on a board
which may treat them as different devices. Currently I've seen only
two NP10T devices with various IDs. Possibly Petatel NP10T list will
be appended upon devices with new IDs will appear.
Signed-off-by: Daniil Bolsun <dan.bolsun@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Signed-off-by: Jóhann B. Guðmundsson <johannbg@fedoraproject.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The device report an error capacity when read_capacity_16().
Using read_capacity_10() can get the correct capacity.
Signed-off-by: Ren Bigcren <bigcren.ren@sonymobile.com>
Cc: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Oskar Andero <oskar.andero@sonymobile.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This adds NetGear Managed Switch M4100 series, M5300 series, M7100 series
USB ID (0846:0110) to the cp210x driver. Without this, the serial
adapter is not recognized in Linux. Description was obtained from
an Netgear Eng.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

some MUSB incarnations, such as those governed by
omap2430.c and tusb6010.c, have three resources, not
two.

Fix the bug created by commit 09fc7d22 (usb: musb:
fix incorrect usage of resource pointer) where only
two of the three resources would be passed to musb_core.c

[ balbi@ti.com : add tusb6010.c to original patch ]
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

The hub driver was recently changed to use "global" suspend for system
suspend transitions on non-SuperSpeed buses.  This means that we don't
suspend devices individually by setting the suspend feature on the
upstream hub port; instead devices all go into suspend automatically
when the root hub stops transmitting packets.  The idea was to save
time and to avoid certain kinds of wakeup races.

Now it turns out that many hubs are buggy; they don't relay wakeup
requests from a downstream port to their upstream port if the
downstream port's suspend feature is not set (depending on the speed
of the downstream port, whether or not the hub is enabled for remote
wakeup, and possibly other factors).

We can't have hubs dropping wakeup requests.  Therefore this patch
goes partway back to the old policy: It sets the suspend feature for a
port if the device attached to that port or any of its descendants is
enabled for wakeup.  People will still be able to benefit from the
time savings if they don't care about wakeup and leave it disabled on
all their devices.

In order to accomplish this, the patch adds a new field to the usb_hub
structure: wakeup_enabled_descendants is a count of how many devices
below a suspended hub are enabled for remote wakeup.  A corresponding
new subroutine determines the number of wakeup-enabled devices at or
below an arbitrary suspended USB device.

This should be applied to the 3.10 stable kernel.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: Toralf Förster <toralf.foerster@gmx.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>