On the W83795ADG, there's a single pin for BEEP and OVT#, so you
can't have both. Check the configuration and don't create beep
attributes when BEEP pin is not available.

The W83795G has a dedicated BEEP pin so the functionality is always
available there.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>

When asked to clear the intrusion alarm, do so immediately. We have to
invalidate the cache to make sure the new status will be read. But we
also have to read from the status register once to clear the pending
alarm, as writing to CLR_CHS surprising won't clear it automatically.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>

We can't read the intrusion state from the real-time alarm registers
as we do for all other alarm flags, because real-time alarm bits don't
stick (by definition) and the intrusion state has to stick until
explicitly cleared (otherwise it has little value.)

So we have to use the interrupt status register instead, which is read
from the same address but with a configuration bit flipped in another
register.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>

Don't expose raw register values to user-space. Decode and encode
temperature channels selected as temperature sources as needed.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>

Temperature sources are not correlated directly with temperature
channels. A look-up table is required to find out which temperature
sources can be used depending on which temperature channels (both
analog and digital) are enabled.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>

Expose fan control method (DC vs. PWM) using the standard sysfs
attributes. I've made it read-only as the board should be wired for
a given mode, the BIOS should have set up the chip for this mode, and
you shouldn't have to change it. But it would be easy enough to make
it changeable if someone comes up with a use case.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>

There were two bugs:
* Speed cruise mode was improperly reported for all fans but fan1.
* Fan control method (PWM vs. DC) was mixed with the control mode.
  It will be added back as a separate attribute, as per the standard
  sysfs interface.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>

This clears the following build-time warnings I was seeing:

drivers/hwmon/lm95241.c: In function "set_interval":
drivers/hwmon/lm95241.c:132:15: warning: ignoring return value of "strict_strtol", declared with attribute warn_unused_result
drivers/hwmon/lm95241.c: In function "set_max2":
drivers/hwmon/lm95241.c:278:1: warning: ignoring return value of "strict_strtol", declared with attribute warn_unused_result
drivers/hwmon/lm95241.c: In function "set_max1":
drivers/hwmon/lm95241.c:277:1: warning: ignoring return value of "strict_strtol", declared with attribute warn_unused_result
drivers/hwmon/lm95241.c: In function "set_min2":
drivers/hwmon/lm95241.c:249:1: warning: ignoring return value of "strict_strtol", declared with attribute warn_unused_result
drivers/hwmon/lm95241.c: In function "set_min1":
drivers/hwmon/lm95241.c:248:1: warning: ignoring return value of "strict_strtol", declared with attribute warn_unused_result
drivers/hwmon/lm95241.c: In function "set_type2":
drivers/hwmon/lm95241.c:220:1: warning: ignoring return value of "strict_strtol", declared with attribute warn_unused_result
drivers/hwmon/lm95241.c: In function "set_type1":
drivers/hwmon/lm95241.c:219:1: warning: ignoring return value of "strict_strtol", declared with attribute warn_unused_result

This also fixes a small race in set_interval() as a side effect: by
working with a temporary local variable we prevent data->interval from
being accessed at a time it contains the interval value in the wrong
unit.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Davide Rizzo <elpa.rizzo@gmail.com>

My old mail address doesn't exist anymore. This changes all occurrences
to my new address.
Signed-off-by: Hans J. Koch <hjk@hansjkoch.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

* 'urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/brodo/pcmcia-2.6:
  drivers/pcmcia/soc_common.c: Use printf extension %pV
  pcmcia: fix warning in synclink driver
  pcmcia/sa1100: don't put machine specific init functions in .init.text
  pcmcia/cm4000: fix error code
  pd6729: Coding Style fixes

This reverts commit 47d3904f.

Crashes any x86 serial console bootup:

  Console: colour VGA+ 80x25
  BUG: unable to handle kernel NULL pointer dereference at 0000000000000158
  IP: [<ffffffff811ebcb4>] serial8250_do_set_termios+0x1d4/0x430
  ...
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Greg KH <gregkh@suse.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: padlock - Fix AES-CBC handling on odd-block-sized input
  crypto: n2 - dubious error check

* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6:
  [media] soc-camera: Compile fixes for mx2-camera
  [media] SoC Camera: ov6650: minor cleanups
  [media] SOC Camera: OMAP1: typo fix
  [media] SoC Camera: OMAP1: update for recent videobuf changes
  [media] SoC Camera: OMAP1: update for recent framework changes
  [media] ARM mx3_camera: check for DMA engine type
  [media] tm6000: bugfix set tv standards
  [media] cafe_ccic: fix subdev configuration
  [media] saa7134: Fix autodetect for Behold A7 and H7 TV cards
  [media] v4l: kill the BKL
  [media] BZ#22292: dibx000_common: Restore i2c algo pointer

More recent GCC caused the i8k driver to stop working, on Slackware
compiler was upgraded from gcc-4.4.4 to gcc-4.5.1 after which it didn't
work anymore, meaning the driver didn't load or gave total nonsensical
output.

As it turned out the asm(..) statement forgot to mention it modifies the
*regs variable.

Credits to Andi Kleen and Andreas Schwab for providing the fix.
Signed-off-by: Jim Bos <jim876@xs4all.nl>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Currently we have:

  --w--w--w-. 1 root root 0 2010-11-11 14:56 /sys/kernel/debug/acpi/custom_method

which is just crazy. Change this to --w-------.
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Cc: stable@kernel.org (for 2.6.36)
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (66 commits)
  can-bcm: fix minor heap overflow
  gianfar: Do not call device_set_wakeup_enable() under a spinlock
  ipv6: Warn users if maximum number of routes is reached.
  docs: Add neigh/gc_thresh3 and route/max_size documentation.
  axnet_cs: fix resume problem for some Ax88790 chip
  ipv6: addrconf: don't remove address state on ifdown if the address is being kept
  tcp: Don't change unlocked socket state in tcp_v4_err().
  x25: Prevent crashing when parsing bad X.25 facilities
  cxgb4vf: add call to Firmware to reset VF State.
  cxgb4vf: Fail open if link_start() fails.
  cxgb4vf: flesh out PCI Device ID Table ...
  cxgb4vf: fix some errors in Gather List to skb conversion
  cxgb4vf: fix bug in Generic Receive Offload
  cxgb4vf: don't implement trivial (and incorrect) ndo_select_queue()
  ixgbe: Look inside vlan when determining offload protocol.
  bnx2x: Look inside vlan when determining checksum proto.
  vlan: Add function to retrieve EtherType from vlan packets.
  virtio-net: init link state correctly
  ucc_geth: Fix deadlock
  ucc_geth: Do not bring the whole IF down when TX failure.
  ...

* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  drivers/ata/pata_octeon_cf.c: delete double assignment
  pata_legacy: fix CONFIG_PATA_WINBOND_VLB_MODULE test
  libata: fix NULL sdev dereference race in atapi_qc_complete()

* 'staging-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6: (38 commits)
  Revert "staging: tidspbridge: replace iommu custom for opensource implementation"
  Revert "staging: tidspbridge - move shared memory iommu maps to tiomap3430.c"
  Revert "staging: tidspbridge - rename bridge_brd_mem_map/unmap to a proper name"
  Revert "staging: tidspbridge - remove custom mmu code from tiomap3430.c"
  Revert "staging: tidspbridge - fix mmufault support"
  Revert "staging: tidspbridge - remove hw directory"
  Revert "staging: tidspbridge - move all iommu related code to a new file"
  Revert "staging: tidspbridge: remove dw_dmmu_base from cfg_hostres struct"
  Revert "staging: tidspbridge - remove reserved memory clean up"
  Revert "staging: tidspbridge - deprecate reserve/unreserve_memory funtions"
  Revert "staging: tidspbridge - remove dmm custom module"
  Revert "staging: tidspbridge - update Kconfig to select IOMMU module"
  staging: tidspbridge: hardcode SCM macros while fix is upstreamed
  Staging: keucr driver: fix uninitialized variable & proper memset length
  omap: dsp: remove shm from normal memory
  Staging: wlan-ng: Fix wrong #ifdef #endif sequence
  Staging: Update parameters for cfg80211 key management operation
  Staging: ath6kl: Fix pointer casts on 64-bit architectures
  Staging: batman-adv: suppress false warning when changing the mac address
  Staging: batman-adv: fix interface alternating and bonding reggression
  ...

* 'usb-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (28 commits)
  Revert "USB: xhci: Use GFP_ATOMIC under spin_lock"
  USB: ohci-jz4740: Fix spelling in MODULE_ALIAS
  UWB: Return UWB_RSV_ALLOC_NOT_FOUND rather than crashing on NULL dereference if kzalloc fails
  usb: core: fix information leak to userland
  usb: misc: iowarrior: fix information leak to userland
  usb: misc: sisusbvga: fix information leak to userland
  usb: subtle increased memory usage in u_serial
  USB: option: fix when the driver is loaded incorrectly for some Huawei devices.
  USB: xhci: Use GFP_ATOMIC under spin_lock
  usb: gadget: goku_udc: add registered flag bit, fixing build
  USB: ehci/mxc: compile fix
  USB: Fix FSL USB driver on non Open Firmware systems
  USB: the development of the usb tree is now in git
  usb: musb: fail unaligned DMA transfers on v1.8 and above
  USB: ftdi_sio: add device IDs for Milkymist One JTAG/serial
  usb.h: fix ioctl kernel-doc info
  usb: musb: gadget: kill duplicate code in musb_gadget_queue()
  usb: musb: Fix handling of spurious SESSREQ
  usb: musb: fix kernel oops when loading musb_hdrc module for the 2nd time
  USB: musb: blackfin: push clkin value to platform resources
  ...

* 'tty-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
  n_gsm: Fix length handling
  n_gsm: Copy n2 over when configuring via ioctl interface
  serial: bfin_5xx: grab port lock before making port termios changes
  serial: bfin_5xx: disable CON_PRINTBUFFER for consoles
  serial: bfin_5xx: remove redundant SSYNC to improve TX speed
  serial: bfin_5xx: always include DMA headers
  vcs: make proper usage of the poll flags
  amiserial: Remove unused variable icount
  8250: Fix tcsetattr to avoid ioctl(TIOCMIWAIT) hang
  tty_ldisc: Fix BUG() on hangup
  TTY: restore tty_ldisc_wait_idle
  SERIAL: blacklist si3052 chip
  drivers/serial/bfin_5xx.c: Fix line continuation defects
  tty: prevent DOS in the flush_to_ldisc
  8250: add support for Kouwell KW-L221N-2
  nozomi: Fix warning from the previous TIOCGCOUNT changes
  tty: fix warning in synclink driver
  tty: Fix formatting in tty.h
  tty: the development tree is now done in git

* 'upstream/core' of git://git.kernel.org/pub/scm/linux/kernel/git/jeremy/xen:
  xen: do not release any memory under 1M in domain 0
  xen: events: do not unmask event channels on resume
  xen: correct size of level2_kernel_pgt

Merge branch 'stable/xen-pcifront-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen

* 'stable/xen-pcifront-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
  MAINTAINERS: Mark XEN lists as moderated
  xen-pcifront: fix PCI reference leak
  xen-pcifront: Remove duplicate inclusion of headers.
  xen: fix memory leak in Xen PCI MSI/MSI-X allocator.
  MAINTAINERS: Update mailing list name for Xen pieces.

Delete successive assignments to the same location.

A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@@
expression i;
@@

*i = ...;
 i = ...;
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

pata_legacy is incorrectly testing PATA_WINBOND_VLB_MODULE instead of
CONFIG_PATA_WINBOND_VLB_MODULE.  Fix it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: "Robert P. J. Day" <rpjday@crashcourse.ca>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

SCSI commands may be issued between __scsi_add_device() and dev->sdev
assignment, so it's unsafe for ata_qc_complete() to dereference
dev->sdev->locked without checking whether it's NULL or not.  Fix it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

On 64-bit platforms the ASCII representation of a pointer may be up to 17
bytes long. This patch increases the length of the buffer accordingly.

http://marc.info/?l=linux-netdev&m=128872251418192&w=2Reported-by: Dan Rosenberg <drosenberg@vsecurity.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
CC: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The gianfar driver calls device_set_wakeup_enable() under a spinlock,
which causes a problem to happen after the recent core power
management changes, because this function can sleep now.  Fix this
by moving the device_set_wakeup_enable() call out of the
spinlock-protected area.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

This gives users at least some clue as to what the problem
might be and how to go about fixing it.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

axnet_cs:
    Some Ax88790 chip need to reinitialize the CISREG_CCSR register
    after resume.
Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, addrconf_ifdown does not delete statically configured IPv6
addresses when the interface is brought down. The intent is that when
the interface comes back up the address will be usable again. However,
this doesn't actually work, because the system stops listening on the
corresponding solicited-node multicast address, so the address cannot
respond to neighbor solicitations and thus receive traffic. Also, the
code notifies the rest of the system that the address is being deleted
(e.g, RTM_DELADDR), even though it is not. Fix it so that none of this
state is updated if the address is being kept on the interface.

Tested: Added a statically configured IPv6 address to an interface,
started ping, brought link down, brought link up again. When link came
up ping kept on going and "ip -6 maddr" showed that the host was still
subscribed to there
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Alexey Kuznetsov noticed a regression introduced by
commit f1ecd5d9
("Revert Backoff [v3]: Revert RTO on ICMP destination unreachable")

The RTO and timer modification code added to tcp_v4_err()
doesn't check sock_owned_by_user(), which if true means we
don't have exclusive access to the socket and therefore cannot
modify it's critical state.

Just skip this new code block if sock_owned_by_user() is true
and eliminate the now superfluous sock_owned_by_user() code
block contained within.
Reported-by: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
CC: Damian Lukowski <damian@tvk.rwth-aachen.de>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>

Now with improved comma support.

On parsing malformed X.25 facilities, decrementing the remaining length
may cause it to underflow.  Since the length is an unsigned integer,
this will result in the loop continuing until the kernel crashes.

This patch adds checks to ensure decrementing the remaining length does
not cause it to wrap around.
Signed-off-by: Dan Rosenberg <drosenberg@vsecurity.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add call to Firmware to reset its VF State when we first attach to the VF.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fail open if link_start() fails.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a bunch of T4 Device IDs for the VF Driver.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There were some errors in the way that internal Gather Lists were being
translated into skb's.  This also makes the VF Driver look more like the PF
Driver to facilitate easier comarison.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix botch in Generic Receive Offload (the Packet Gather List Total length
field wasn't being initialized).
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Don't implement (struct net_device_ops *)->ndo_select_queue() with simple
call to skb_tx_hash().  This leads to non-persistent TX queue selection in
the Linux dev_pick_tx() routine for TCP connections.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently the skb->protocol field is used to setup various
offloading parameters on transmit for the correct protocol.
However, if vlan offloading is disabled or otherwise not used,
the protocol field will be ETH_P_8021Q, not the actual protocol.
This will cause the offloading to be not performed correctly,
even though the hardware is capable of looking inside vlan tags.
Instead, look inside the header if necessary to determine the
correct protocol type.

To some extent this fixes a regression from 2.6.36 because it
was previously not possible to disable vlan offloading and this
error case was not exposed.
Signed-off-by: Hao Zheng <hzheng@nicira.com>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Alex Duyck <alexander.h.duyck@intel.com>
CC: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>