Interrupt endpoints behave much like Bulk endpoints with the exception
that they are periodic. We can pre-issue Start Transfer exactly as we
do for Bulk endpoints.

While at that, remove one trailing blank line which is unnecessary.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

The present code correctly fetches the req which were previously not
queued from the started_list but fails to continue queuing from the sg
where it previously stopped queuing (because of the unavailable TRB's).
This patch correct's the code to continue queuing from the correct sg
present in the sglist.

For example, consider 5 sgs in req. Because of limited TRB's among the
5 sgs only 3 got queued. This patch corrects the code to start queuing
from correct sg i.e 4th sg when the TRBs are available.
Signed-off-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

The code logic in dwc3_prepare_one_trb() incorrectly uses the address
and length fields present in req packet for mapping TRB's instead of
using the address and length fields of scattergather lists. This patch
correct's the code to use sg->address and sg->length when scattergather
lists are present.
Signed-off-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

extcon device is used to detect host/device connection. Since extcon
OF property is deprecated, alternative method should be added.
This method uses OF graph bindings to locate extcon.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Historically, the clocks and resets are handled on the glue layer
side instead of the DWC3 core.  For simple cases, dwc3-of-simple.c
takes care of arbitrary number of clocks and resets.  The DT node
structure typically looks like as follows:

  dwc3-glue {
          compatible = "foo,dwc3";
          clocks = ...;
          resets = ...;
          ...

          dwc3 {
                  compatible = "snps,dwc3";
                  ...
          };
  }

By supporting the clocks and the reset in the dwc3/core.c, it will
be turned into a single node:

  dwc3 {
          compatible = "foo,dwc3", "snps,dwc3";
          clocks = ...;
          resets = ...;
          ...
  }

This commit adds the binding of clocks and resets specific to this IP.
The number of clocks should generally be the same across SoCs, it is
just some SoCs either tie clocks together or do not provide software
control of some of the clocks.

I took the clock names from the Synopsys datasheet: "ref" (ref_clk),
"bus_early" (bus_clk_early), and "suspend" (suspend_clk).

I found only one reset line in the datasheet, hence the reset-names
property is omitted.

Those clocks are required for new platforms.  Enforcing the new
binding breaks existing platforms since they specify clocks (and
resets) in their glue layer node, but nothing in the core node.
I listed such exceptional cases in the DT binding.  The driver
code has been relaxed to accept no clock.  This change is based
on the discussion [1].

I inserted reset_control_deassert() and clk_bulk_enable() before the
first register access, i.e. dwc3_cache_hwparams().

[1] https://patchwork.kernel.org/patch/10284265/Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Fix the fallout of the conversion to GPIO descriptors in 3df03408.
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

The include defines the private platform_data structure used with AVR
platforms. It has no user since 7c55984e. Remove it.
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

When converting to GPIO descriptors, gpiod_get_value automatically
handles the line inversion flags from the device tree.

Do not invert the line twice.

Fixes: 3df03408 ("usb: gadget: udc: atmel: convert to use GPIO descriptors")
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

A message can be forged to crash the stack; here we make sure we don't
completely break the system if this occurs
Signed-off-by: Michel Pollet <michel.pollet@bp.renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

It is not a good idea to directly modify the resource of a platform
device.  Modify its local copy, and pass it to devm_ioremap_resource()
so that we do not need to restore it in the failure path and the remove
hook.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

The USB3CV version 2.1.80 (March 26, 2018) requires all devices
( gen1, gen2, single lane, dual lane) to return the value of 0x0320
in the bcdUSB field
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Some PHY drivers (e.g. for Qualcomm QUSB2 and QMP PHYs) support
runtime PM to reduce PHY power consumption during bus_suspend.
Add changes to let core auto-suspend PHYs on host bus-suspend
using GUSB2PHYCFG register if needed for a platform. Also perform
PHYs runtime suspend/resume and let platform glue drivers e.g.
dwc3-qcom handle remote wakeup during bus suspend by waking up
devices on receiving wakeup event from PHY.
Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

DWC3 controller on Qualcomm SOCs has a Qscratch wrapper.
Some of its uses are described below resulting in need to
have a separate glue driver instead of using dwc3-of-simple:
 - It exposes register interface to override vbus-override
   and lane0-pwr-present signals going to hardware. These
   must be updated in peripheral mode for DWC3 if vbus lines
   are not connected to hardware block. Otherwise RX termination
   in SS mode or DP pull-up is not applied by device controller.
 - pwr_events_irq_stat support to check if USB2 PHY is in L2 state
   before glue driver proceeds with suspend.
 - Support for wakeup interrupts lines that are asserted whenever
   there is any wakeup event on USB3 or USB2 bus.
 - Support to replace pip3 clock going to DWC3 with utmi clock
   for hardware configuration where SSPHY is not used with DWC3.
Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Existing documentation has lot of incorrect information as it
was originally added for a driver that no longer exists.
Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Add compatible string to use this generic glue layer to support
Allwinner H6 platform's dwc3 controller.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

In case there are multiple ecm instances, either for multiple
otg controllers, or multiple virtual links using libcomposite,
each instance needs to have its own host mac address string
value for iMACAddress.

Update the source array (ecm_string_defs), every time before
usb_gstrings_attach(). Without that, all links wrongly were
getting the same, last allocated, host mac address, rather
than the correct one, as requested via configfs.
Signed-off-by: Lukasz Nowak <lukasz.nowak@exablue.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Fixes: <b3e3893e> ("net: use core MTU range checking")
which patched only one of two functions used to setup the
USB Gadget Ethernet driver, causing a serious performance
regression in the ability to increase mtu size above 1500.
Signed-off-by: John Greb <h3x4m3r0n@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

The current frame_number is read from core for both
device and host modes. Reading of the current frame
number needs to be performed ASAP due to IRQ latency's.
This is why, it is moved to common interrupt handler.

Accordingly updated dwc2_gadget_target_frame_elapsed()
function which uses stored frame_number instead of
reading frame number.

In cases when target frame value is incremented
the frame_number is required to read again.
Signed-off-by: Artur Petrosyan <arturp@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Dumping the registers via debugfs makes USB on Raspberry Pi completely
unusable. The read of register GRXSTSP ("Receive Status Read and Pop
Register") is responsible for this behaviour, because it pops the RX FIFO.
So avoid this by omitting the relevant register.

CC: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Fixes: 563cf017 ("usb: dwc2: debugfs: add support for complete register dump")
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Crash caused by going out of "eps_out" array range.
Iteration on "eps_out" changed to less than "num_of_eps".
Signed-off-by: Artur Petrosyan <arturp@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Added GHWCFG4_IPG_ISOC_SUPPORTED and DCFG_IPG_ISOC_SUPPORDED
bits definitions to enable/disable IPG feature.

Added ipg_isoc_en core parameter which will indicate IPG support
enable/disable and initialize it.
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

In DDMA mode required to enable BNA interrupt for
both directions.
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Changed existing two descriptor-chain flow to one chain.

In two-chain implementation BNA interrupt used for switching between
two chains. BNA interrupt asserted because of returning to
beginning of the chain based on L-bit of last descriptor.

Because of that we lose packets. This issue resolved by using one
desc-chain.

Removed all staff related to two desc-chain flow from
DDMA ISOC related functions.

Removed request length checking from dwc2_gadget_fill_isoc_desc()
function. Request length checking added to dwc2_hsotg_ep_queue()
function. If request length greater than descriptor limits then
request not added to queue. Additional checking done for High
Bandwidth ISOC OUT's which not supported by driver. In
dwc2_gadget_fill_isoc_desc() function also checked desc-chain
status (full or not) to avoid of reusing not yet processed
descriptors.

In dwc2_gadget_start_isoc_ddma() function creation of desc-chain
always started from descriptor 0. Before filling descriptors, they
were initialized by HOST BUSY status.

In dwc2_gadget_complete_isoc_request_ddma() added checking for
desc-chain rollover. Also added checking completion status.
Request completed successfully if DEV_DMA_STS is DEV_DMA_STS_SUCC,
otherwise complete with actual=0. For systems with high IRQ latency
added pointer compl_desc to next descriptor to be completed by
XferCompl interrupt. This pointer replace descriptor index calculation
based on DxEPDMA register. On descriptor completion interrupt
processing all descriptors starting from compl_desc till descriptor
which Buffer Status field not equal DMA_DONE status.

Actually removed dwc2_gadget_start_next_isoc_ddma() function because
now driver use only one desc-chain and instead that function added
dwc2_gadget_handle_isoc_bna() function for handling BNA interrupts.

Handling BNA interrupt done by flushing TxFIFOs for OUT EPs,
completing request with actual=0 and resetting desc-chain number and
target frame to initial values for restarting transfers.

On handling NAK request completed with actual=0. Incremented target
frame to allow fill desc chain and start transfers.
In DDMA mode avoided of frame number incrementing, because tracking
of frame number performed in dwc2_gadget_fill_isoc_desc() function.

When core assert XferCompl along with BNA, we should ignore XferCompl
in dwc2_hsotg_epint() function.

On BNA interrupt replaced dwc2_gadget_start_next_isoc_ddma() by above
mentioned BNA handler.

In dwc2_hsotg_ep_enable() function added sanity check of bInterval
for ISOC IN in DDMA mode, because HW doesn't supported EP's with
bInterval more than 10 and check for mc for ISOC OUT transfers,
because core doesn't support high bandwidth transfers.
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

In fact the driver depends on EXTCON only when it's configed as
USB_MTU3_DUAL_ROLE, so make USB_MTU3_DUAL_ROLE depend on EXTCON but
not USB_MTU3.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

There is an error dialog popped up in PC when test TEST_J/K
by EHSETT tool, due to not waiting for the completion of
control transfer. Here fix it by entering test mode after
Status Stage finish.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

When boot on the platform with the USB cable connected to Win7,
the Win7 will pop up an error dialog: "USB Device not recognized",
but finally the Win7 can enumerate it successfully.
The root cause is as the following:
When the xHCI driver set PORT_POWER of the OTG port, and if both
IDPIN and VBUS_VALID are high at the same time, the MTU3 controller
will set SESSION and pull up DP, so the Win7 can detect existence
of USB device, but if the mtu3 driver can't switch to device mode
during the debounce time, the Win7 can not enumerate it.
Here to fix it by removing the 1s delayed EXTCON register to speed up
mode switch.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

The usb_add_gadget_udc() will set the gadget state as
USB_STATE_NOTATTACHED, so we needn't set it again.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

The variable of 'count' is declared as u8, this will cause an issue
due to value truncated when works in SS or SSP mode and data length
is greater than 255, so change it as u32.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

We should get drvdata from struct device directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

We should get drvdata from struct device directly. Going via
platform_device is an unneeded step back and forth.
Acked-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Tegra's EHCI driver has a build dependency on Tegra's PHY driver and
currently Tegra's PHY driver is built only when Tegra's EHCI driver is
built. Add own Kconfig entry for the Tegra's PHY driver so that drivers
other than ehci-tegra (like ChipIdea UDC) could work with ehci-tegra
driver being disabled in kernels config by allowing user to manually
select the PHY driver.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

UTMI pads are shared by USB controllers and reset of UTMI pads is shared
with the reset of USB1 controller. Currently reset of UTMI pads is done by
the EHCI driver and ChipIdea UDC works because EHCI driver always happen
to be probed first. Move reset controls from ehci-tegra to tegra-phy in
order to resolve the problem.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Tegra's PHY driver has a mix of pr_err() and dev_err(), let's switch to
dev_err() and use common errors message formatting across the driver for
consistency.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

This allows 32 bit owners of ffs endpoints to
make ioctls into a 64 bit kernel.

All of the current epfile ioctls can be handled
with the same struct definitions as regular
ioctl.
Acked-by: Michał Nazarewicz <mina86@mina86.com>
Signed-off-by: Jerry Zhang <zhangjerry@google.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Currently, the midi function is not freed until it is
both removed from the config and released by the user.
Since the user could take a long time to release the
card, it's possible that the function could be unlinked
and thus f_midi_opts would be null when freeing f_midi.

Thus, refcount f_midi_opts and only free it when it is
unlinked and all f_midis have been freed.
Signed-off-by: Jerry Zhang <zhangjerry@google.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

The Aspeed BMC SoCs support a "virtual hub" function. It provides some
HW support for a top-level USB2 hub behind which sit 5 gadget "ports".

This driver adds support for the full functionality, emulating the
hub standard requests and exposing 5 UDC gadget drivers corresponding
to the ports.

The hub itself has HW provided dedicated EP0 and EP1 (the latter for
hub interrupts). It also has dedicated EP0s for each function. For
other endpoints, there's a pool of 15 "generic" endpoints that are
shared among the ports.

The driver relies on my previous patch adding a "dispose" EP op to
handle EP allocation between ports. EPs are allocated from the shared
pool in the UDC "match_ep" callback and assigned to the UDC instance
(added to the gadget ep_list).

When the composite driver gets unbound, the new hook will allow the UDC
to clean things up and return those EPs to the shared pool.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

The table is never modified by the function. This allows us
to use it on a statically defined table that is marked const.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Improve the kerneldoc for usb_ep_queue() to note explicitly that the
request's completion routine will be called if and only if the return
value is 0.  The corresponding fact about usb_submit_urb() for the
host-side API has long been documented, and this has always been the
intention for the gadget API.  But until now, documentation seems to
have been lacking.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Pull drm fixes from Dave Airlie:
 "Exynos, i915, vc4, amdgpu fixes.

  i915:
   - an oops fix
   - two race fixes
   - some gvt fixes

  amdgpu:
   - dark screen fix
   - clk/voltage fix
   - vega12 smu fix

  vc4:
   - memory leak fix

  exynos just drops some code"

* tag 'drm-fixes-for-v4.17-rc2' of git://people.freedesktop.org/~airlied/linux: (23 commits)
  drm/amd/powerplay: header file interface to SMU update
  drm/amd/pp: Fix bug voltage can't be OD separately on VI
  drm/amd/display: Don't program bypass on linear regamma LUT
  drm/i915: Fix LSPCON TMDS output buffer enabling from low-power state
  drm/i915/audio: Fix audio detection issue on GLK
  drm/i915: Call i915_perf_fini() on init_hw error unwind
  drm/i915/bios: filter out invalid DDC pins from VBT child devices
  drm/i915/pmu: Inspect runtime PM state more carefully while estimating RC6
  drm/i915: Do no use kfree() to free a kmem_cache_alloc() return value
  drm/exynos: exynos_drm_fb -> drm_framebuffer
  drm/exynos: Move dma_addr out of exynos_drm_fb
  drm/exynos: Move GEM BOs to drm_framebuffer
  drm: Fix HDCP downstream dev count read
  drm/vc4: Fix memory leak during BO teardown
  drm/i915/execlists: Clear user-active flag on preemption completion
  drm/i915/gvt: Add drm_format_mod update
  drm/i915/gvt: Disable primary/sprite/cursor plane at virtual display initialization
  drm/i915/gvt: Delete redundant error message in fb_decode.c
  drm/i915/gvt: Cancel dma map when resetting ggtt entries
  drm/i915/gvt: Missed to cancel dma map for ggtt entries
  ...