Add support for configuring the machine constraints
valid_modes_mask element based on a list of allowed modes
specified via a device tree property.
Signed-off-by: David Collins <collinsd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

Add a common device tree property for regulator nodes to support
the specification of allowed operating modes.
Signed-off-by: David Collins <collinsd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

Regulators attached via RPMh on Qualcomm sdm845 apparently are
write-only.  Specifically you can send a request for a certain voltage
but you can't read back to see what voltage you've requested.  What
this means is that at bootup we have absolutely no idea what voltage
we could be at.

As discussed in the patches to try to support the RPMh regulators [1],
the fact that regulators are write-only means that its driver's
get_voltage_sel() should return an error code if it's called before
any calls to set_voltage_sel().  This causes problems in
machine_constraints_voltage() when trying to apply the constraints.

A proposed fix was to come up with an error code that could be
returned by get_voltage_sel() which would cause the regulator
framework to simply try setting the voltage with the current
constraints.

In this patch I propose the error code -ENOTRECOVERABLE.  In errno.h
this error is described as "State not recoverable".  Though the error
code was originally intended "for robust mutexes", the description of
the error code seems to apply here because we can't read the state of
the regulator.  Also note that the only existing user of this error
code in the regulator framework is tps65090-regulator.c which returns
this error code from the enable() call (not get_voltage() or
get_voltage_sel()), so there should be no existing regulators that
might accidentally get the new behavior.  (Side note is that tps65090
seems to interpret this error code to mean an error that you can't
recover from rather than some data that can't be recovered).

[1] https://patchwork.kernel.org/patch/10340897/Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

SY8106A is an I2C attached single output regulator made by Silergy Corp,
which is used on several Allwinner H3/H5 SBCs to control the power
supply of the ARM cores.

Add a driver for it.
Signed-off-by: Ondrej Jirman <megous@megous.com>
[Icenowy: Change commit message, remove enable/disable code, add default
 ramp_delay, add comment for go bit, add code for fixed mode voltage]
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

SY8106A is an I2C-controlled adjustable voltage regulator made by
Silergy Corp.

Add its device tree binding.
Signed-off-by: Ondrej Jirman <megous@megous.com>
[Icenowy: Change commit message and slight fixes]
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

If device tree is not enabled, of_find_regulator_by_node() should have
a dummy function since the function call is still there.

This is to fix build error after CONFIG_NO_AUTO_INLINE is introduced.
If this option is enabled, GCC will not auto-inline functions that are
not explicitly marked as inline.

In this case (no CONFIG_OF), the copmiler will report error in function
regulator_dev_lookup().

W/O NO_AUTO_INLINE, function of_get_regulator() is auto-inlined and then
the call to of_find_regulator_by_node() is optimized out since
of_get_regulator() always return NULL.

W/ NO_AUTO_INLINE, the return value of of_get_regulator() is a variable
so the call to of_find_regulator_by_node() cannot be optimized out. So
we need a stub of_find_regulator_by_node().

static struct regulator_dev *regulator_dev_lookup(struct device *dev,
						  const char *supply)
{
	struct regulator_dev *r = NULL;
	struct device_node *node;
	struct regulator_map *map;
	const char *devname = NULL;

	regulator_supply_alias(&dev, &supply);

	/* first do a dt based lookup */
	if (dev && dev->of_node) {
		node = of_get_regulator(dev, supply);
		if (node) {
			r = of_find_regulator_by_node(node);
			if (r)
				return r;
	...
Signed-off-by: Changbin Du <changbin.du@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

According to Devicetree Specification v0.2 document:

"The name of a node should be somewhat generic, reflecting the function
of the device and not its precise programming model."

Do as suggested in the binding example.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Merge branch 'topic/bd9571mwv' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator into regulator-4.18

The BD9571MWV PMIC supports backup mode, which keeps one or more DDR
rails powered while the main SoC is powered down.

Which DDR rails are to be kept powered is board-specific, and controlled
using the optional "rohm,ddr-backup-power" DT property.  In the absence
of this property, backup mode is not available.

Backup mode can be enabled or disabled by the user using the standard
"wakeup" virtual file in sysfs, e.g. to enable:

    echo enabled > /sys/devices/platform/soc/e60b0000.i2c/i2c-7/7-0030/bd9571mwv-regulator.2.auto/power/wakeup

When the PMIC is configured for backup mode, the role of the accessory
power switch changes from a power switch to a wake-up switch.
Two types of switches (or signals) can be used:
  A. With a momentary power switch (or pulse signal), the PMIC is
     configured for backup mode in the PMIC driver's suspend callback,
     during system suspend.
     Backup mode is enabled by default, as there is no further impact
     during normal system operation.

  B. With a toggle power switch (or level signal), the following steps
     must be followed exactly:
       1. Configure PMIC for backup mode,
       2. Switch accessory power switch off, to prepare for system
          suspend, which is a manual step not controlled by software,
       3. Suspend system.
     This mode is not yet supported by the driver.

As the switch type is board-specific, and cannot be determined
automatically, it is obtained from the presence of one of the
"rohm,rstbmode-*" properties in DT.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

Enable read/write access to the BD9571MWV_BKUP_MODE_CNT register, which
is amongst others used to configure DDR Backup Power.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

Add definitions for the KEEPON_* bits in the "BKUP Mode Cnt" register,
which control the DDR rails to be kept powered when backup mode is
enabled.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

Document the new optional properties related to DDR Backup Mode and
toggle/momentary power switches.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

Like axp221, axp223, axp813 the axp803 is also supporting external
regulator to drive the  OTG VBus through N_VBUSEN PMIC pin.

Add support for it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

It seems that the loop index i is not being incremented and hence
potentially the while loop could spin forever. Fortunately with the
data being used this does not appear to happen at the moment.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

In of_get_regulation_constraints() we were taking the result of
of_map_mode() (an unsigned int) and assigning it to an int.  We were
then checking whether this value was -EINVAL.  Some implementers of
of_map_mode() were returning -EINVAL (even though the return type of
their function needed to be unsigned int) because they needed to
signal an error back to of_get_regulation_constraints().

In general in the regulator framework the mode is always referred to
as an unsigned int.  While we could fix this to be a signed int (the
highest value we store in there right now is 0x8), it's actually
pretty clean to just define the regulator mode 0x0 (the lack of any
bits set) as an invalid mode.  Let's do that.

Fixes: 5e5e3a42 ("regulator: of: Add support for parsing initial and suspend modes")
Suggested-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

This version is exists in the Samsung Galaxy Tab 10.1 which is based on the
Nvidia Tegra 2 board. The TPS658624 has the same SM2 voltage table as
TPS658623.
Signed-off-by: ryang <decatf@gmail.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

pfuze3000 datasheet(Rev.9.0) from:

https://www.nxp.com/docs/en/data-sheet/PF3000.pdf

updates sw1a's voltage range, the settings for 1.450V and 1.475V
are replaced with 1.8V and 3.3V:

5b'11110 1.450 (SW1B), 1.8 (SW1A/SW1AB)
5b'11111 1.475 (SW1B), 3.3 (SW1A/SW1AB)

the voltage calculation using steps is NOT available for sw1a now,
use voltage table instead.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Buck10 is a multi(dual) phase regulator. So as part of enabling it
turn on the LP87565_BUCK_CTRL_1_FPWM_MP_0_2 bit which forces it to
operate always in multiphase and forced-PWM operation mode.
This helps improve the transient voltage response while switching OPP.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

The slew rate might need a +/- 15% margin as per the latest data manual:

	http://www.ti.com/lit/ds/snvsb22/snvsb22.pdf

Hence take a conservative approach to program 85% of the original
hardware slew rate so that the software accommodates the margin
delay while voltage switching. Hence reduce the default ramp_delay
populated in the descriptors also by 15%.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

The AB8540 was an evolved version of the AB8500, but it was never
mass produced or put into products, only reference designs exist.
The upstream support was never completed and it is unlikely that
this will happen so drop the support for now to simplify
maintenance of the AB8500.

Cc: Loic Pallardy <loic.pallardy@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

Pull more btrfs updates from David Sterba:
 "We have queued a few more fixes (error handling, log replay,
  softlockup) and the rest is SPDX updates that touche almost all files
  so the diffstat is long"

* tag 'for-4.17-part2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
  btrfs: Only check first key for committed tree blocks
  btrfs: add SPDX header to Kconfig
  btrfs: replace GPL boilerplate by SPDX -- sources
  btrfs: replace GPL boilerplate by SPDX -- headers
  Btrfs: fix loss of prealloc extents past i_size after fsync log replay
  Btrfs: clean up resources during umount after trans is aborted
  btrfs: Fix possible softlock on single core machines
  Btrfs: bail out on error during replay_dir_deletes
  Btrfs: fix NULL pointer dereference in log_dir_items

Pull cifs fixes from Steve French:
 "SMB3 fixes, a few for stable, and some important cleanup work from
  Ronnie of the smb3 transport code"

* tag '4.17-rc1SMB3-Fixes' of git://git.samba.org/sfrench/cifs-2.6:
  cifs: change validate_buf to validate_iov
  cifs: remove rfc1002 hardcoded constants from cifs_discard_remaining_data()
  cifs: Change SMB2_open to return an iov for the error parameter
  cifs: add resp_buf_size to the mid_q_entry structure
  smb3.11: replace a 4 with server->vals->header_preamble_size
  cifs: replace a 4 with server->vals->header_preamble_size
  cifs: add pdu_size to the TCP_Server_Info structure
  SMB311: Improve checking of negotiate security contexts
  SMB3: Fix length checking of SMB3.11 negotiate request
  CIFS: add ONCE flag for cifs_dbg type
  cifs: Use ULL suffix for 64-bit constant
  SMB3: Log at least once if tree connect fails during reconnect
  cifs: smb2pdu: Fix potential NULL pointer dereference

Pull SCSI fixes from James Bottomley:
 "This is a set of minor (and safe changes) that didn't make the initial
  pull request plus some bug fixes.

  The status handling code is actually a running regression from the
  previous merge window which had an incomplete fix (now reverted) and
  most of the remaining bug fixes are for problems older than the
  current merge window"

[ Side note: this merge also takes the base kernel git repository to 6+
  million objects for the first time. Technically we hit it a couple of
  merges ago already if you count all the tag objects, but now it
  reaches 6M+ objects reachable from HEAD.

  I was joking around that that's when I should switch to 5.0, because
  3.0 happened at the 2M mark, and 4.0 happened at 4M objects. But
  probably not, even if numerology is about as good a reason as any.

                                                              - Linus ]

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: devinfo: Add Microsoft iSCSI target to 1024 sector blacklist
  scsi: cxgb4i: silence overflow warning in t4_uld_rx_handler()
  scsi: dpt_i2o: Use after free in I2ORESETCMD ioctl
  scsi: core: Make scsi_result_to_blk_status() recognize CONDITION MET
  scsi: core: Rename __scsi_error_from_host_byte() into scsi_result_to_blk_status()
  Revert "scsi: core: return BLK_STS_OK for DID_OK in __scsi_error_from_host_byte()"
  scsi: aacraid: Insure command thread is not recursively stopped
  scsi: qla2xxx: Correct setting of SAM_STAT_CHECK_CONDITION
  scsi: qla2xxx: correctly shift host byte
  scsi: qla2xxx: Fix race condition between iocb timeout and initialisation
  scsi: qla2xxx: Avoid double completion of abort command
  scsi: qla2xxx: Fix small memory leak in qla2x00_probe_one on probe failure
  scsi: scsi_dh: Don't look for NULL devices handlers by name
  scsi: core: remove redundant assignment to shost->use_blk_mq

Pull more Kbuild updates from Masahiro Yamada:

 - pass HOSTLDFLAGS when compiling single .c host programs

 - build genksyms lexer and parser files instead of using shipped
   versions

 - rename *-asn1.[ch] to *.asn1.[ch] for suffix consistency

 - let the top .gitignore globally ignore artifacts generated by flex,
   bison, and asn1_compiler

 - let the top Makefile globally clean artifacts generated by flex,
   bison, and asn1_compiler

 - use safer .SECONDARY marker instead of .PRECIOUS to prevent
   intermediate files from being removed

 - support -fmacro-prefix-map option to make __FILE__ a relative path

 - fix # escaping to prepare for the future GNU Make release

 - clean up deb-pkg by using debian tools instead of handrolled
   source/changes generation

 - improve rpm-pkg portability by supporting kernel-install as a
   fallback of new-kernel-pkg

 - extend Kconfig listnewconfig target to provide more information

* tag 'kbuild-v4.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
  kconfig: extend output of 'listnewconfig'
  kbuild: rpm-pkg: use kernel-install as a fallback for new-kernel-pkg
  Kbuild: fix # escaping in .cmd files for future Make
  kbuild: deb-pkg: split generating packaging and build
  kbuild: use -fmacro-prefix-map to make __FILE__ a relative path
  kbuild: mark $(targets) as .SECONDARY and remove .PRECIOUS markers
  kbuild: rename *-asn1.[ch] to *.asn1.[ch]
  kbuild: clean up *-asn1.[ch] patterns from top-level Makefile
  .gitignore: move *-asn1.[ch] patterns to the top-level .gitignore
  kbuild: add %.dtb.S and %.dtb to 'targets' automatically
  kbuild: add %.lex.c and %.tab.[ch] to 'targets' automatically
  genksyms: generate lexer and parser during build instead of shipping
  kbuild: clean up *.lex.c and *.tab.[ch] patterns from top-level Makefile
  .gitignore: move *.lex.c *.tab.[ch] patterns to the top-level .gitignore
  kbuild: use HOSTLDFLAGS for single .c executables

Pull x86 fixes from Thomas Gleixner:
 "A set of fixes and updates for x86:

   - Address a swiotlb regression which was caused by the recent DMA
     rework and made driver fail because dma_direct_supported() returned
     false

   - Fix a signedness bug in the APIC ID validation which caused invalid
     APIC IDs to be detected as valid thereby bloating the CPU possible
     space.

   - Fix inconsisten config dependcy/select magic for the MFD_CS5535
     driver.

   - Fix a corruption of the physical address space bits when encryption
     has reduced the address space and late cpuinfo updates overwrite
     the reduced bit information with the original value.

   - Dominiks syscall rework which consolidates the architecture
     specific syscall functions so all syscalls can be wrapped with the
     same macros. This allows to switch x86/64 to struct pt_regs based
     syscalls. Extend the clearing of user space controlled registers in
     the entry patch to the lower registers"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/apic: Fix signedness bug in APIC ID validity checks
  x86/cpu: Prevent cpuinfo_x86::x86_phys_bits adjustment corruption
  x86/olpc: Fix inconsistent MFD_CS5535 configuration
  swiotlb: Use dma_direct_supported() for swiotlb_ops
  syscalls/x86: Adapt syscall_wrapper.h to the new syscall stub naming convention
  syscalls/core, syscalls/x86: Rename struct pt_regs-based sys_*() to __x64_sys_*()
  syscalls/core, syscalls/x86: Clean up compat syscall stub naming convention
  syscalls/core, syscalls/x86: Clean up syscall stub naming convention
  syscalls/x86: Extend register clearing on syscall entry to lower registers
  syscalls/x86: Unconditionally enable 'struct pt_regs' based syscalls on x86_64
  syscalls/x86: Use 'struct pt_regs' based syscall calling for IA32_EMULATION and x32
  syscalls/core: Prepare CONFIG_ARCH_HAS_SYSCALL_WRAPPER=y for compat syscalls
  syscalls/x86: Use 'struct pt_regs' based syscall calling convention for 64-bit syscalls
  syscalls/core: Introduce CONFIG_ARCH_HAS_SYSCALL_WRAPPER=y
  x86/syscalls: Don't pointlessly reload the system call number
  x86/mm: Fix documentation of module mapping range with 4-level paging
  x86/cpuid: Switch to 'static const' specifier

Pull x86 pti updates from Thomas Gleixner:
 "Another series of PTI related changes:

   - Remove the manual stack switch for user entries from the idtentry
     code. This debloats entry by 5k+ bytes of text.

   - Use the proper types for the asm/bootparam.h defines to prevent
     user space compile errors.

   - Use PAGE_GLOBAL for !PCID systems to gain back performance

   - Prevent setting of huge PUD/PMD entries when the entries are not
     leaf entries otherwise the entries to which the PUD/PMD points to
     and are populated get lost"

* 'x86-pti-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/pgtable: Don't set huge PUD/PMD on non-leaf entries
  x86/pti: Leave kernel text global for !PCID
  x86/pti: Never implicitly clear _PAGE_GLOBAL for kernel image
  x86/pti: Enable global pages for shared areas
  x86/mm: Do not forbid _PAGE_RW before init for __ro_after_init
  x86/mm: Comment _PAGE_GLOBAL mystery
  x86/mm: Remove extra filtering in pageattr code
  x86/mm: Do not auto-massage page protections
  x86/espfix: Document use of _PAGE_GLOBAL
  x86/mm: Introduce "default" kernel PTE mask
  x86/mm: Undo double _PAGE_PSE clearing
  x86/mm: Factor out pageattr _PAGE_GLOBAL setting
  x86/entry/64: Drop idtentry's manual stack switch for user entries
  x86/uapi: Fix asm/bootparam.h userspace compilation errors

Pull scheduler fixes from Thomas Gleixner:
 "A few scheduler fixes:

   - Prevent a bogus warning vs. runqueue clock update flags in
     do_sched_rt_period_timer()

   - Simplify the helper functions which handle requests for skipping
     the runqueue clock updat.

   - Do not unlock the tunables mutex in the error path of the cpu
     frequency scheduler utils. Its not held.

   - Enforce proper alignement for 'struct util_est' in sched_avg to
     prevent a misalignment fault on IA64"

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/core: Force proper alignment of 'struct util_est'
  sched/core: Simplify helpers for rq clock update skip requests
  sched/rt: Fix rq->clock_update_flags < RQCF_ACT_SKIP warning
  sched/cpufreq/schedutil: Fix error path mutex unlock

Pull more perf updates from Thomas Gleixner:
 "A rather large set of perf updates:

  Kernel:

   - Fix various initialization issues

   - Prevent creating [ku]probes for not CAP_SYS_ADMIN users

  Tooling:

   - Show only failing syscalls with 'perf trace --failure' (Arnaldo
     Carvalho de Melo)

            e.g: See what 'openat' syscalls are failing:

        # perf trace --failure -e openat
         762.323 ( 0.007 ms): VideoCapture/4566 openat(dfd: CWD, filename: /dev/video2) = -1 ENOENT No such file or directory
         <SNIP N /dev/videoN open attempts... sigh, where is that improvised camera lid?!? >
         790.228 ( 0.008 ms): VideoCapture/4566 openat(dfd: CWD, filename: /dev/video63) = -1 ENOENT No such file or directory
        ^C#

   - Show information about the event (freq, nr_samples, total
     period/nr_events) in the annotate --tui and --stdio2 'perf
     annotate' output, similar to the first line in the 'perf report
     --tui', but just for the samples for a the annotated symbol
     (Arnaldo Carvalho de Melo)

   - Introduce 'perf version --build-options' to show what features were
     linked, aliased as well as a shorter 'perf -vv' (Jin Yao)

   - Add a "dso_size" sort order (Kim Phillips)

   - Remove redundant ')' in the tracepoint output in 'perf trace'
     (Changbin Du)

   - Synchronize x86's cpufeatures.h, no effect on toolss (Arnaldo
     Carvalho de Melo)

   - Show group details on the title line in the annotate browser and
     'perf annotate --stdio2' output, so that the per-event columns can
     have headers (Arnaldo Carvalho de Melo)

   - Fixup vertical line separating metrics from instructions and
     cleaning unused lines at the bottom, both in the annotate TUI
     browser (Arnaldo Carvalho de Melo)

   - Remove duplicated 'samples' in lost samples warning in
     'perf report' (Arnaldo Carvalho de Melo)

   - Synchronize i915_drm.h, silencing the perf build process,
     automagically adding support for the new DRM_I915_QUERY ioctl
     (Arnaldo Carvalho de Melo)

   - Make auxtrace_queues__add_buffer() allocate struct buffer, from a
     patchkit already applied (Adrian Hunter)

   - Fix the --stdio2/TUI annotate output to include group details, be
     it for a recorded '{a,b,f}' explicit event group or when forcing
     group display using 'perf report --group' for a set of events not
     recorded as a group (Arnaldo Carvalho de Melo)

   - Fix display artifacts in the ui browser (base class for the
     annotate and main report/top TUI browser) related to the extra
     title lines work (Arnaldo Carvalho de Melo)

   - perf auxtrace refactorings, leftovers from a previously partially
     processed patchset (Adrian Hunter)

   - Fix the builtin clang build (Sandipan Das, Arnaldo Carvalho de
     Melo)

   - Synchronize i915_drm.h, silencing a perf build warning and in the
     process automagically adding support for a new ioctl command
     (Arnaldo Carvalho de Melo)

   - Fix a strncpy issue in uprobe tracing"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (36 commits)
  perf/core: Need CAP_SYS_ADMIN to create k/uprobe with perf_event_open()
  tracing/uprobe_event: Fix strncpy corner case
  perf/core: Fix perf_uprobe_init()
  perf/core: Fix perf_kprobe_init()
  perf/core: Fix use-after-free in uprobe_perf_close()
  perf tests clang: Fix function name for clang IR test
  perf clang: Add support for recent clang versions
  perf tools: Fix perf builds with clang support
  perf tools: No need to include namespaces.h in util.h
  perf hists browser: Remove leftover from row returned from refresh
  perf hists browser: Show extra_title_lines in the 'D' debug hotkey
  perf auxtrace: Make auxtrace_queues__add_buffer() do CPU filtering
  tools headers uapi: Synchronize i915_drm.h
  perf report: Remove duplicated 'samples' in lost samples warning
  perf ui browser: Fixup cleaning unused lines at the bottom
  perf annotate browser: Fixup vertical line separating metrics from instructions
  perf annotate: Show group details on the title line
  perf auxtrace: Make auxtrace_queues__add_buffer() allocate struct buffer
  perf/x86/intel: Move regs->flags EXACT bit init
  perf trace: Remove redundant ')'
  ...

Pull x86 EFI bootup fixlet from Thomas Gleixner:
 "A single fix for an early boot warning caused by invoking
  this_cpu_has() before SMP initialization"

* 'efi-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/mm: Fix bogus warning during EFI bootup, use boot_cpu_has() instead of this_cpu_has() in build_cr3_noflush()

Pull irq affinity fixes from Thomas Gleixner:

  - Fix error path handling in the affinity spreading code

  - Make affinity spreading smarter to avoid issues on systems which
    claim to have hotpluggable CPUs while in fact they can't hotplug
    anything.

    So instead of trying to spread the vectors (and thereby the
    associated device queues) to all possibe CPUs, spread them on all
    present CPUs first. If there are left over vectors after that first
    step they are spread among the possible, but not present CPUs which
    keeps the code backwards compatible for virtual decives and NVME
    which allocate a queue per possible CPU, but makes the spreading
    smarter for devices which have less queues than possible or present
    CPUs.

* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  genirq/affinity: Spread irq vectors among present CPUs as far as possible
  genirq/affinity: Allow irq spreading from a given starting point
  genirq/affinity: Move actual irq vector spreading into a helper function
  genirq/affinity: Rename *node_to_possible_cpumask as *node_to_cpumask
  genirq/affinity: Don't return with empty affinity masks on error

Pull OpenRISC fixlet from Stafford Horne:
 "Just one small thing here, it came in a while back but I didnt have
  anything in my 4.16 queue, still its the only thing for 4.17 so
  sending it alone.

  Small cleanup: remove unused __ARCH_HAVE_MMU define"

* tag 'for-linus' of git://github.com/openrisc/linux:
  openrisc: remove unused __ARCH_HAVE_MMU define

Pull powerpc fixes from Michael Ellerman:

 - Fix crashes when loading modules built with a different
   CONFIG_RELOCATABLE value by adding CONFIG_RELOCATABLE to vermagic.

 - Fix busy loops in the OPAL NVRAM driver if we get certain error
   conditions from firmware.

 - Remove tlbie trace points from KVM code that's called in real mode,
   because it causes crashes.

 - Fix checkstops caused by invalid tlbiel on Power9 Radix.

 - Ensure the set of CPU features we "know" are always enabled is
   actually the minimal set when we build with support for firmware
   supplied CPU features.

Thanks to: Aneesh Kumar K.V, Anshuman Khandual, Nicholas Piggin.

* tag 'powerpc-4.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/64s: Fix CPU_FTRS_ALWAYS vs DT CPU features
  powerpc/mm/radix: Fix checkstops caused by invalid tlbiel
  KVM: PPC: Book3S HV: trace_tlbie must not be called in realmode
  powerpc/8xx: Fix build with hugetlbfs enabled
  powerpc/powernv: Fix OPAL NVRAM driver OPAL_BUSY loops
  powerpc/powernv: define a standard delay for OPAL_BUSY type retry loops
  powerpc/fscr: Enable interrupts earlier before calling get_user()
  powerpc/64s: Fix section mismatch warnings from setup_rfi_flush()
  powerpc/modules: Fix crashes by adding CONFIG_RELOCATABLE to vermagic

Merge yet more updates from Andrew Morton:

 - various hotfixes

 - kexec_file updates and feature work

* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (27 commits)
  kernel/kexec_file.c: move purgatories sha256 to common code
  kernel/kexec_file.c: allow archs to set purgatory load address
  kernel/kexec_file.c: remove mis-use of sh_offset field during purgatory load
  kernel/kexec_file.c: remove unneeded variables in kexec_purgatory_setup_sechdrs
  kernel/kexec_file.c: remove unneeded for-loop in kexec_purgatory_setup_sechdrs
  kernel/kexec_file.c: split up __kexec_load_puragory
  kernel/kexec_file.c: use read-only sections in arch_kexec_apply_relocations*
  kernel/kexec_file.c: search symbols in read-only kexec_purgatory
  kernel/kexec_file.c: make purgatory_info->ehdr const
  kernel/kexec_file.c: remove checks in kexec_purgatory_load
  include/linux/kexec.h: silence compile warnings
  kexec_file, x86: move re-factored code to generic side
  x86: kexec_file: clean up prepare_elf64_headers()
  x86: kexec_file: lift CRASH_MAX_RANGES limit on crash_mem buffer
  x86: kexec_file: remove X86_64 dependency from prepare_elf64_headers()
  x86: kexec_file: purge system-ram walking from prepare_elf64_headers()
  kexec_file,x86,powerpc: factor out kexec_file_ops functions
  kexec_file: make use of purgatory optional
  proc: revalidate misc dentries
  mm, slab: reschedule cache_reap() on the same CPU
  ...

The code to verify the new kernels sha digest is applicable for all
architectures.  Move it to common code.

One problem is the string.c implementation on x86.  Currently sha256
includes x86/boot/string.h which defines memcpy and memset to be gcc
builtins.  By moving the sha256 implementation to common code and
changing the include to linux/string.h both functions are no longer
defined.  Thus definitions have to be provided in x86/purgatory/string.c

Link: http://lkml.kernel.org/r/20180321112751.22196-12-prudo@linux.vnet.ibm.comSigned-off-by: Philipp Rudo <prudo@linux.vnet.ibm.com>
Acked-by: Dave Young <dyoung@redhat.com>
Cc: AKASHI Takahiro <takahiro.akashi@linaro.org>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

For s390 new kernels are loaded to fixed addresses in memory before they
are booted.  With the current code this is a problem as it assumes the
kernel will be loaded to an 'arbitrary' address.  In particular,
kexec_locate_mem_hole searches for a large enough memory region and sets
the load address (kexec_bufer->mem) to it.

Luckily there is a simple workaround for this problem.  By returning 1
in arch_kexec_walk_mem, kexec_locate_mem_hole is turned off.  This
allows the architecture to set kbuf->mem by hand.  While the trick works
fine for the kernel it does not for the purgatory as here the
architectures don't have access to its kexec_buffer.

Give architectures access to the purgatories kexec_buffer by changing
kexec_load_purgatory to take a pointer to it.  With this change
architectures have access to the buffer and can edit it as they need.

A nice side effect of this change is that we can get rid of the
purgatory_info->purgatory_load_address field.  As now the information
stored there can directly be accessed from kbuf->mem.

Link: http://lkml.kernel.org/r/20180321112751.22196-11-prudo@linux.vnet.ibm.comSigned-off-by: Philipp Rudo <prudo@linux.vnet.ibm.com>
Reviewed-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Acked-by: Dave Young <dyoung@redhat.com>
Cc: AKASHI Takahiro <takahiro.akashi@linaro.org>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The current code uses the sh_offset field in purgatory_info->sechdrs to
store a pointer to the current load address of the section.  Depending
whether the section will be loaded or not this is either a pointer into
purgatory_info->purgatory_buf or kexec_purgatory.  This is not only a
violation of the ELF standard but also makes the code very hard to
understand as you cannot tell if the memory you are using is read-only
or not.

Remove this misuse and store the offset of the section in
pugaroty_info->purgatory_buf in sh_offset.

Link: http://lkml.kernel.org/r/20180321112751.22196-10-prudo@linux.vnet.ibm.comSigned-off-by: Philipp Rudo <prudo@linux.vnet.ibm.com>
Acked-by: Dave Young <dyoung@redhat.com>
Cc: AKASHI Takahiro <takahiro.akashi@linaro.org>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The main loop currently uses quite a lot of variables to update the
section headers.  Some of them are unnecessary.  So clean them up a
little.

Link: http://lkml.kernel.org/r/20180321112751.22196-9-prudo@linux.vnet.ibm.comSigned-off-by: Philipp Rudo <prudo@linux.vnet.ibm.com>
Acked-by: Dave Young <dyoung@redhat.com>
Cc: AKASHI Takahiro <takahiro.akashi@linaro.org>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

To update the entry point there is an extra loop over all section
headers although this can be done in the main loop.  So move it there
and eliminate the extra loop and variable to store the 'entry section
index'.

Also, in the main loop, move the usual case, i.e.  non-bss section, out
of the extra if-block.

Link: http://lkml.kernel.org/r/20180321112751.22196-8-prudo@linux.vnet.ibm.comSigned-off-by: Philipp Rudo <prudo@linux.vnet.ibm.com>
Reviewed-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Acked-by: Dave Young <dyoung@redhat.com>
Cc: AKASHI Takahiro <takahiro.akashi@linaro.org>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

When inspecting __kexec_load_purgatory you find that it has two tasks

	1) setting up the kexec_buffer for the new kernel and,
	2) setting up pi->sechdrs for the final load address.

The two tasks are independent of each other.  To improve readability
split up __kexec_load_purgatory into two functions, one for each task,
and call them directly from kexec_load_purgatory.

Link: http://lkml.kernel.org/r/20180321112751.22196-7-prudo@linux.vnet.ibm.comSigned-off-by: Philipp Rudo <prudo@linux.vnet.ibm.com>
Acked-by: Dave Young <dyoung@redhat.com>
Cc: AKASHI Takahiro <takahiro.akashi@linaro.org>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>