Add GRO capability to IPv4 GRE tunnels, using the gro_cells
infrastructure.

Tested using IPv4 and IPv6 TCP traffic inside this tunnel, and
checking GRO is building large packets.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This adds a new include file (include/net/gro_cells.h), to bring GRO
(Generic Receive Offload) capability to tunnels, in a modular way.

Because tunnels receive path is lockless, and GRO adds a serialization
using a napi_struct, I chose to add an array of up to
DEFAULT_MAX_NUM_RSS_QUEUES cells, so that multi queue devices wont be
slowed down because of GRO layer.

skb_get_rx_queue() is used as selector.

In the future, we might add optional fanout capabilities, using rxhash
for example.

With help from Ben Hutchings who reminded me
netif_get_num_default_rss_queues() function.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

skb with CHECKSUM_NONE cant currently be handled by GRO, and
we notice this deep in GRO stack in tcp[46]_gro_receive()

But there are cases where GRO can be a benefit, even with a lack
of checksums.

This preliminary work is needed to add GRO support
to tunnels.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When an address is added on loopback (ip -6 a a 2002::1/128 dev lo), two routes
are added:
 - one in the local table:
    local 2002::1 via :: dev lo  proto none  metric 0
 - one the in main table (for the prefix):
    unreachable 2002::1 dev lo  proto kernel  metric 256  error -101

When the address is deleted, the route inserted in the main table remains
because we use rt6_lookup(), which returns NULL when dst->error is set, which
is the case here! Thus, it is better to use ip6_route_lookup() to avoid this
kind of filter.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch moves the bnx2x and cnic drivers into using FW 7.8.2
which was recently submitted into the linux-firmware tree.

A short summary of minor bugs fixed by this FW:
 1. In switch dependent mode, fix several issues regarding inner vlan
    vs. DCB priorities.
 2. iSCSI - not all packets were completed on a forward channel.
 3. DCB - fixed for 4-port devices.
 4. Fixed false parity reported in CAM memories when operating near -5%
    on the 1.0V core supply.
 5. ETS default settings are set to fairness between traffic classes
    (rather than strict priority), and uses the same chip receive buffer
    configuration for both PFC and pause.

For a complete list of fixes made by this FW, see commit 236367db
in the linux-firmware git repository.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Current VFs enumeration algorithm used in be_find_vfs does not take domain
number into the match. The match found in igb/ixgbe is more elegant and
safe.

This 2nd version uses pci_physfn instead of checking dev->physfn directly.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit ec47ea82(skb: Add inline helper for getting the skb end offset from
head) introduces this helper function, skb_end_offset(),
we should make use of it.
Signed-off-by: Weiping Pan <wpan@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next into for-davem

John W. Linville says:

====================
Here is another batch of updates intended for 3.7...

Highlights include an hci_connect re-write in Bluetooth, HCI/LLC
layer separation in NFC, removal of the raw pn544 NFC driver, NFC LLCP
raw sockets support, improved IBSS auth frame handling in mac80211,
full-MAC AP mode notification support in mac80211, a lot of attention
paid to brcmfmac, and the usual level of updates to iwlwifi, ath9k,
mwifiex, and rt2x00, and various other updates.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Added and modified a few log messages mostly in probe path.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

1) link_status_query() is always called to query the link-speed (speed
after applying qos). When there is no qos setting, link-speed is derived from
port-speed. Do all this inside this routine and hide this from the callers.

2) adpater->phy.forced_port_speed is not being set anywhere after being
initialized. Get rid of this variable.

3) Ignore async link_speed notifications till the initial value has been
fetched from FW.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

All invocations of this routine use the same type value.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Simple round-robin hardware TX scheduling can cause starvation of TX rings
with small packets when other TX rings have large TSO or jumbo packets.

In the simplest case, consider 2 TCP streams running in opposite
directions.  The TSO TX traffic will hash to one ring and the ACKs for the
incoming data on a different TCP connection will hash to a different TX
ring.  The hardware fetches one complete TSO packet (up to 64K data)
before servicing the other TX ring.  When it gets to the other TX ring, it
will only fetch one packet (64-byte ACK packet in this case).  After that,
it will switch back to the 1st ring filled with more TSO packets.  Because
only one ACK can go out roughly every 500 usec in this case, the incoming
data rate becomes very low.

Update version to 3.125.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Default remains the same.
Reviewed-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

by introducing tg3_stop() that does the opposite of tg3_start().  This
function will be useful when adding the support for changing the numbe
of rx and tx rings.
Reviewed-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

by introducing tg3_start() that handles all initialization steps from
IRQ allocation.  This function will be needed when adding support for
changing the number of rx and tx rings.
Reviewed-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

since the number of rings can be different.
Reviewed-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

irq_cnt is no longer necessarily equal to the number rx or tx rings.
Reviewed-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is preparation work to allow the number of RX and TX rings to be
configured separately.
Reviewed-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

fib6_add_1() should consistently return errno pointers,
rather than a mixture of NULL and errno pointers.
Signed-off-by: Lin Ming <mlin@ss.pku.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>

Marc Kleine-Budde says:

====================
this pull request is for net-next, for the v3.7 release cycle.
AnilKumar Ch contributed a fix for a segfault in the c_can driver,
which is triggered by an earlier commit [1] in net-next (so no backport
is needed).
...
[1] 4cdd34b2 can: c_can: Add runtime PM support to Bosch C_CAN/D_CAN controller
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch enables wake from system suspend on magic packet.

Patch updated to change BUG_ON to WARN_ON_ONCE.
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch instructs the device to enter its lowest power SUSPEND2
state during system suspend.

This patch also explicitly wakes the device after resume, which
should address reports of the device not automatically coming
back after system suspend:

Patch updated to change BUG_ON to WARN_ON_ONCE.

http://code.google.com/p/chromium-os/issues/detail?id=31871Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds an explicit test that the READY bit is set on
the device when attempting to initialize it.

If this bit is clear then the device hasn't succesfully started
all its clocks, and this patch helps make the resulting logged
error more helpful.
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch enables wake from system suspend on magic packet.

Patch updated to replace BUG_ON with WARN_ON_ONCE and return.
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch enables the device to enter its lowest power SUSPEND2
state during system suspend, instead of staying up using full power.

Patch updated to not add two pointers to .suspend & .resume.

Patch updated to replace BUG_ON with WARN_ON_ONCE and return.
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes an issue on some systems, where after suspend the
link is re-established but the ethernet interface does not resume.
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds additional checks of the values returned by
smsc95xx_(read|write)_reg, and wraps their common patterns
in macros.
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Removes unnecessary variables as smsc95xx_write_reg takes its
value by parameter.  Early versions passed this parameter by
reference.

Also replace hardcoded interrupt status value with a #define
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

During init, the device reset is unexpected to complete immediately,
so sleep before testing the condition rather than after it.
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Conflicts:
	drivers/net/team/team.c
	drivers/net/usb/qmi_wwan.c
	net/batman-adv/bat_iv_ogm.c
	net/ipv4/fib_frontend.c
	net/ipv4/route.c
	net/l2tp/l2tp_netlink.c

The team, fib_frontend, route, and l2tp_netlink conflicts were simply
overlapping changes.

qmi_wwan and bat_iv_ogm were of the "use HEAD" variety.

With help from Antonio Quartulli.
Signed-off-by: David S. Miller <davem@davemloft.net>

The WLAN/BT weights have to set correctly before BTCOEX
is initialized. Currently, this is not done for all chips
in the AR9003 family. This patch fixes this issue by setting
the weights in the init path. While at it, rename ar9462_wlan_weights
to mci_wlan_weights since it is common to both AR9462 and AR9565.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Convert cpu_to_le16(le16_to_cpu(E1) + E2) to use le16_add_cpu().

dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Once hostsleep is activated, this patch takes care of not
dropping packets in RX reorder table.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Interrupts with the sync_cause AR_INTR_SYNC_HOST1_FATAL and
AR_INTR_SYNC_HOST1_PERR have to be handled using a chip reset. Otherwise a
interrupt storm with unhandled interrupts will cause a hang or crash of the
machine.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The function brcmf_update_prof() only add complexity that is not
needed.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The function brcmf_read_prof() provided access to fields
with brcmf_cfg80211_profile structure using a field id,
but the calling function can easily access that structure
directly. This patch removes the function.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Renamed structure to brcmf_cfg80211_info as it is not really a
private structure since it is exposed in header file.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>