The I2C core always reports the MODALIAS uevent as "i2c:<client name"
regardless if the driver was matched using the I2C id_table or the
of_match_table. So the driver needs to export the I2C table and this
be built into the module or udev won't have the necessary information
to auto load the correct module when the device is added.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

The USB Battery Charging spec (BC1.2) suggests a dedicated
charging port can deliver from 0.5 to 5.0A at between 4.75 and 5.25
volts.

To choose the "correct" current voltage setting requires a trial
and error approach: try to draw current and see if the voltage drops
too low.

Even with a configured Standard Downstream Port, it may not be possible
to reliably pull 500mA - depending on cable quality and source
quality I have reports of charging failure due to the voltage dropping
too low.

To address both these concerns, this patch introduce incremental
current setting.
The current pull from VBUS is increased in steps of 20mA every 100ms
until the target is reached or until the measure voltage drops below
4.75V.  If the voltage does go too low, the target current is reduced
by 20mA and kept there.

This applies to currents selected automatically, or to values
set via sysfs.  So setting a large value will cause the maximum
available to be used - up to the limit of 1.7A imposed by the
hardware.
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

This allows AC charging to be turned off, much like usb charging.
"continuous" mode is not available though.
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

Add a 'continuous' option for usb charging which enables
the "linear" charging mode of the twl4030.

Linear charging does a good job with not-so-reliable power sources.
Auto mode does not work well as it switches off when voltage drops
momentarily.  Care must be taken not to over-charge.

It was used with a bike hub dynamo since a year or so. In that case
there are automatically charging stops when the cyclist needs a break.
Original-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

'off' or 'auto' to

 /sys/class/power/twl4030_usb/mode

will now enable or disable charging from USB port.  Normally this is
enabled on 'plug' and disabled on 'unplug'.
Unplug will still disable charging.  'plug' will only enable it if
'auto' if selected.
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

'max_current' sysfs attributes are created which allow the
max to be set.
Whenever a current source changes, the default is restored.
This will be followed by a uevent, so user-space can decide to
update again.
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

The twl4030 charger has two current sources, 'USB' and 'AC'
(presumably "Accessory Charger" because it isn't Alternating Current).

If 'AC' is providing current, we should set the current limit
differently to when it isn't (and so USB is used).
So split 'cur' into 'usb_cur' and 'ac_cur' and use accordingly.

Now we must review the current setting on any interrupt or USB
event which might indicate that the charger-source has changed.
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

The twl4030 allows control of the incoming current.
Part of this control is a 'CGAIN' setting which doubles
the range for half the precision.  This control affects
several different current setting, so all need to be updated
at once when CGAIN is changed.

With this patch, all of these current setting are managed
by the driver, but most are left at their default settings.

The current drawn is set to 500mA if the allow_usb module parameter is
set, and to 100mA otherwise.
More fine control will appear in later patches.
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

We will need this calculation in other places, so
create functions to map between register value and uA value.
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

The usb phy driver already determines when VBUS is available,
so repeating the test in the charger driver is pointless duplication.

On probe, process the last event from the phy, and from then on,
do whatever the phy tells us without double-checking.
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

Now that twl4030_bci_probe can safely return -EPROBE_DEFER,
do so when devm_usb_get_phy_by_node returns that error.
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

Drivers using module_platform_driver_probe cannot return
EPROBE_DEFER from the probe function, which makes them rather useless
these days...

Convert to module_platform_driver() so EPROBE_DEFER can be used.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

The twl4030 usb phy needs to be active while we are using
the USB VBUS as a current source for charging.
In particular, the usb3v1 regulator must be enabled and the
PHY_PWR_PHYPWD bit must be set to keep the phy powered.

commit ab37813f
    twl4030_charger: Allow charger to control the regulator that feeds it

gave the charger control over the regulator, but didn't resolve
the PHY_PWR_PHYPWD issue.

Now that both of these are controlled by runtime_pm in
phy-twl4030-usb, we can simply take a runtime_pm reference to the USB
phy whenever the charger wants to use it as a current source.

So this patch reverts the above commit, and adds the necessary
runtime_pm calls.
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

For compatibility between board code and DT, set battery name to same value.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

The adaptive voltage scaling framework is not maintained
via the power supply tree and has its own entry in the
MAINTAINERS file, so add an exception in the power supply
entry.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Acked-by: Kevin Hilman <khilman@linaro.org>

The change removes redundant sysfs binary file boundary check while
reading eeprom content from userspace, the check is done on caller
side in fs/sysfs/file.c, if binary attribute size is not zero.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

The change removes redundant calculation of left space on eeprom while
reading or writing "param_eeprom" or "user_eeprom", the checks are not
needed, since this task is done on caller side in fs/sysfs/file.c
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

The change removes redundant sysfs binary file boundary checks while
reading or writing "param_eeprom" or "user_eeprom", the checks are not
needed, since this task is done on caller side in fs/sysfs/file.c
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

Use managed resource functions like devm_kasprintf and
devm_power_supply_register in bq24735_charger_probe. To be
compatible with the change, replace various gotos by direct
returns and drop unneeded labels.

Also, remove bq24735_charger_remove as it is now redundant.
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

Including ARM related header file cause build failure
in i386 build because COMILE_TEST also involve building
zx driver. Remove the unnecessary include file.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

Remove space before tab.
Remove unnecessary line continuations.
Add braces to else statement.
Remove unnecessary parentheses.
Remove unneeded blank lines.
Remove unnecessary 'out of memory' message.
Add missing line after declarations.
Change use of printk to pr_err.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Acked-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

Fix the alignment of function parameters on new lines.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Acked-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

Shorted lines over 80 characters long by reducing tab count.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Acked-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

Add the manufacturer property to the bq27x00 driver.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Dan Murphy <dmurphy@ti.com>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

Register with kernel restart handler instead of setting arm_pm_restart
directly.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

Make it possible to set the name of the supply from the devicetree.
Like other power supply drivers just use the node name. This makes
the code smaller as well, as it doesn't need to allocate memory to
hold the name and allocate a unique ID.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

Final allocations/registrations are now managed by devres.
Signed-off-by: NeilBrown <neilb@suse.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

This simplifies the error paths.
Signed-off-by: NeilBrown <neilb@suse.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

This patch introduces a new compatible string: "atmel,sama5d3-rstc" and
new reset function for sama5d3 and later chips.

As in sama5d3 or later chips, we don't have to shutdown the DDR
controller before reset. Shutdown the DDR controller before reset is a
workaround to avoid DDR signal driving the bus, but since sama5d3 and
later chips there is no such a conflict.

So in this patch:
   1. the sama5d3 reset function only need to write the rstc register
and return.
   2. we can remove the code related with sama5d3 DDR controller as
we don't use it at all.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

i2c_driver does not need to set an owner because i2c_register_driver()
will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

Charging events this patch refers to are:
- charger is connected to/disconnected from the power source
- battery is reconnected to the charger, after it was absent.

When the charger is connected to/disconnected from the power source, CHRVPI
interrupt occurs and PWR_RDY bit is either set or cleared. PWR_RDY bit is
updated after 1-2 seconds CHRVPI interrupt has occurred.
power_supply_changed() should be called after PWR_RDY bit is updated.
/sys/class/power_supply/rt9455-charger/online file displays the value of
PWR_RDY bit.
This way, if the userspace is notified that a charging event has occurred
and the userspace reads /sys/class/power_supply/rt9455-charger/online file,
this file is properly updated when the userspace reads it.
This is the reason why power_supply_changed() is called in
rt9455_pwr_rdy_work_callback(), instead of being called in interrupt
handler.

Since no interrupt is triggered when the battery is reconnected to the
charger, the userspace is never notified that the battery is reconnected.
This is why power_supply_changed() is called in
rt9455_max_charging_time_work_callback(), so that the userspace is notified
that the battery is reconnected.
Signed-off-by: Anda-Maria Nicolae <anda-maria.nicolae@intel.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

Merge tag 'platform-drivers-x86-v4.2-2' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86

Pull late x86 platform driver updates from Darren Hart:
 "The following came in a bit later and I wanted them to bake in next a
  few more days before submitting, thus the second pull.

  A new intel_pmc_ipc driver, a symmetrical allocation and free fix in
  dell-laptop, a couple minor fixes, and some updated documentation in
  the dell-laptop comments.

  intel_pmc_ipc:
   - Add Intel Apollo Lake PMC IPC driver

  tc1100-wmi:
   - Delete an unnecessary check before the function call "kfree"

  dell-laptop:
   - Fix allocating & freeing SMI buffer page
   - Show info about WiGig and UWB in debugfs
   - Update information about wireless control"

* tag 'platform-drivers-x86-v4.2-2' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86:
  intel_pmc_ipc: Add Intel Apollo Lake PMC IPC driver
  tc1100-wmi: Delete an unnecessary check before the function call "kfree"
  dell-laptop: Fix allocating & freeing SMI buffer page
  dell-laptop: Show info about WiGig and UWB in debugfs
  dell-laptop: Update information about wireless control

Pull more vfs updates from Al Viro:
 "Assorted VFS fixes and related cleanups (IMO the most interesting in
  that part are f_path-related things and Eric's descriptor-related
  stuff).  UFS regression fixes (it got broken last cycle).  9P fixes.
  fs-cache series, DAX patches, Jan's file_remove_suid() work"

[ I'd say this is much more than "fixes and related cleanups".  The
  file_table locking rule change by Eric Dumazet is a rather big and
  fundamental update even if the patch isn't huge.   - Linus ]

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (49 commits)
  9p: cope with bogus responses from server in p9_client_{read,write}
  p9_client_write(): avoid double p9_free_req()
  9p: forgetting to cancel request on interrupted zero-copy RPC
  dax: bdev_direct_access() may sleep
  block: Add support for DAX reads/writes to block devices
  dax: Use copy_from_iter_nocache
  dax: Add block size note to documentation
  fs/file.c: __fget() and dup2() atomicity rules
  fs/file.c: don't acquire files->file_lock in fd_install()
  fs:super:get_anon_bdev: fix race condition could cause dev exceed its upper limitation
  vfs: avoid creation of inode number 0 in get_next_ino
  namei: make set_root_rcu() return void
  make simple_positive() public
  ufs: use dir_pages instead of ufs_dir_pages()
  pagemap.h: move dir_pages() over there
  remove the pointless include of lglock.h
  fs: cleanup slight list_entry abuse
  xfs: Correctly lock inode when removing suid and file capabilities
  fs: Call security_ops->inode_killpriv on truncate
  fs: Provide function telling whether file_remove_privs() will do anything
  ...

Commit 835a6a2f ("Bluetooth: Stop sabotaging list poisoning")
thought that the code was sabotaging the list poisoning when NULL'ing
out the list pointers and removed it.

But what was going on was that the bluetooth code was using NULL
pointers for the list as a way to mark it empty, and that commit just
broke it (and replaced the test with NULL with a "list_empty()" test on
a uninitialized list instead, breaking things even further).

So fix it all up to use the regular and real list_empty() handling
(which does not use NULL, but a pointer to itself), also making sure to
initialize the list properly (the previous NULL case was initialized
implicitly by the session being allocated with kzalloc())

This is a combination of patches by Marcel Holtmann and Tedd Ho-Jeong
An.

[ I would normally expect to get this through the bt tree, but I'm going
  to release -rc1, so I'm just committing this directly   - Linus ]
Reported-and-tested-by: Jörg Otte <jrg.otte@gmail.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Original-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Original-by: Marcel Holtmann <marcel@holtmann.org>:
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull SCSI target updates from Nicholas Bellinger:
 "It's been a busy development cycle for target-core in a number of
  different areas.

  The fabric API usage for se_node_acl allocation is now within
  target-core code, dropping the external API callers for all fabric
  drivers tree-wide.

  There is a new conversion to RCU hlists for se_node_acl and
  se_portal_group LUN mappings, that turns fast-past LUN lookup into a
  completely lockless code-path.  It also removes the original
  hard-coded limitation of 256 LUNs per fabric endpoint.

  The configfs attributes for backends can now be shared between core
  and driver code, allowing existing drivers to use common code while
  still allowing flexibility for new backend provided attributes.

  The highlights include:

   - Merge sbc_verify_dif_* into common code (sagi)
   - Remove iscsi-target support for obsolete IFMarker/OFMarker
     (Christophe Vu-Brugier)
   - Add bidi support in target/user backend (ilias + vangelis + agover)
   - Move se_node_acl allocation into target-core code (hch)
   - Add crc_t10dif_update common helper (akinobu + mkp)
   - Handle target-core odd SGL mapping for data transfer memory
     (akinobu)
   - Move transport ID handling into target-core (hch)
   - Move task tag into struct se_cmd + support 64-bit tags (bart)
   - Convert se_node_acl->device_list[] to RCU hlist (nab + hch +
     paulmck)
   - Convert se_portal_group->tpg_lun_list[] to RCU hlist (nab + hch +
     paulmck)
   - Simplify target backend driver registration (hch)
   - Consolidate + simplify target backend attribute implementations
     (hch + nab)
   - Subsume se_port + t10_alua_tg_pt_gp_member into se_lun (hch)
   - Drop lun_sep_lock for se_lun->lun_se_dev RCU usage (hch + nab)
   - Drop unnecessary core_tpg_register TFO parameter (nab)
   - Use 64-bit LUNs tree-wide (hannes)
   - Drop left-over TARGET_MAX_LUNS_PER_TRANSPORT limit (hannes)"

* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (76 commits)
  target: Bump core version to v5.0
  target: remove target_core_configfs.h
  target: remove unused TARGET_CORE_CONFIG_ROOT define
  target: consolidate version defines
  target: implement WRITE_SAME with UNMAP bit using ->execute_unmap
  target: simplify UNMAP handling
  target: replace se_cmd->execute_rw with a protocol_data field
  target/user: Fix inconsistent kmap_atomic/kunmap_atomic
  target: Send UA when changing LUN inventory
  target: Send UA upon LUN RESET tmr completion
  target: Send UA on ALUA target port group change
  target: Convert se_lun->lun_deve_lock to normal spinlock
  target: use 'se_dev_entry' when allocating UAs
  target: Remove 'ua_nacl' pointer from se_ua structure
  target_core_alua: Correct UA handling when switching states
  xen-scsiback: Fix compile warning for 64-bit LUN
  target: Remove TARGET_MAX_LUNS_PER_TRANSPORT
  target: use 64-bit LUNs
  target: Drop duplicate + unused se_dev_check_wce
  target: Drop unnecessary core_tpg_register TFO parameter
  ...

Pull NTB updates from Jon Mason:
 "This includes a pretty significant reworking of the NTB core code, but
  has already produced some significant performance improvements.

  An abstraction layer was added to allow the hardware and clients to be
  easily added.  This required rewriting the NTB transport layer for
  this abstraction layer.  This modification will allow future "high
  performance" NTB clients.

  In addition to this change, a number of performance modifications were
  added.  These changes include NUMA enablement, using CPU memcpy
  instead of asyncdma, and modification of NTB layer MTU size"

* tag 'ntb-4.2' of git://github.com/jonmason/ntb: (22 commits)
  NTB: Add split BAR output for debugfs stats
  NTB: Change WARN_ON_ONCE to pr_warn_once on unsafe
  NTB: Print driver name and version in module init
  NTB: Increase transport MTU to 64k from 16k
  NTB: Rename Intel code names to platform names
  NTB: Default to CPU memcpy for performance
  NTB: Improve performance with write combining
  NTB: Use NUMA memory in Intel driver
  NTB: Use NUMA memory and DMA chan in transport
  NTB: Rate limit ntb_qp_link_work
  NTB: Add tool test client
  NTB: Add ping pong test client
  NTB: Add parameters for Intel SNB B2B addresses
  NTB: Reset transport QP link stats on down
  NTB: Do not advance transport RX on link down
  NTB: Differentiate transport link down messages
  NTB: Check the device ID to set errata flags
  NTB: Enable link for Intel root port mode in probe
  NTB: Read peer info from local SPAD in transport
  NTB: Split ntb_hw_intel and ntb_transport drivers
  ...

if server claims to have written/read more than we'd told it to,
warn and cap the claimed byte count to avoid advancing more than
we are ready to.

Braino in "9p: switch p9_client_write() to passing it struct iov_iter *";
if response is impossible to parse and we discard the request, get the
out of the loop right there.

Cc: stable@vger.kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

If we'd already sent a request and decide to abort it, we *must*
issue TFLUSH properly and not just blindly reuse the tag, or
we'll get seriously screwed when response eventually arrives
and we confuse it for response to later request that had reused
the same tag.

Cc: stable@vger.kernel.org # v3.2 and later
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>