There is a problem when ipvlan slaves are created on a master device that
is a vmxnet3 device (ipvlan in VMware guests). The vmxnet3 driver does not
support unicast address filtering. When an ipvlan device is brought up in
ipvlan_open(), the ipvlan driver calls dev_uc_add() to add the hardware
address of the vmxnet3 master device to the unicast address list of the
master device, phy_dev->uc. This inevitably leads to the vmxnet3 master
device being forced into promiscuous mode by __dev_set_rx_mode().

Promiscuous mode is switched on the master despite the fact that there is
still only one hardware address that the master device should use for
filtering in order for the ipvlan device to be able to receive packets.
The comment above struct net_device describes the uc_promisc member as a
"counter, that indicates, that promiscuous mode has been enabled due to
the need to listen to additional unicast addresses in a device that does
not implement ndo_set_rx_mode()". Moreover, the design of ipvlan
guarantees that only the hardware address of a master device,
phy_dev->dev_addr, will be used to transmit and receive all packets from
its ipvlan slaves. Thus, the unicast address list of the master device
should not be modified by ipvlan_open() and ipvlan_stop() in order to make
ipvlan a workable option on masters that do not support unicast address
filtering.

Fixes: 2ad7bf36 ("ipvlan: Initial check-in of the IPVLAN driver")
Reported-by: Per Sundstrom <per.sundstrom@redqube.se>
Signed-off-by: Jiri Wiesner <jwiesner@suse.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Acked-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

rhashtable_lookup_get_insert_key doesn't have a parameter `data`. It
does have a parameter `key`, however.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

pkaustub@cisco.com is bouncing, remove it.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Christian Benvenuti <benve@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

These are a couple of read locks that should be write locks.

Fixes: fbb39807 ("ionic: support sr-iov operations")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Similar to commit 38f88c45 ("bonding/alb: properly access headers
in bond_alb_xmit()"), we need to make sure arp header was pulled
in skb->head before blindly accessing it in rlb_arp_xmit().

Remove arp_pkt() private helper, since it is more readable/obvious
to have the following construct back to back :

	if (!pskb_network_may_pull(skb, sizeof(*arp)))
		return NULL;
	arp = (struct arp_pkt *)skb_network_header(skb);

syzbot reported :

BUG: KMSAN: uninit-value in bond_slave_has_mac_rx include/net/bonding.h:704 [inline]
BUG: KMSAN: uninit-value in rlb_arp_xmit drivers/net/bonding/bond_alb.c:662 [inline]
BUG: KMSAN: uninit-value in bond_alb_xmit+0x575/0x25e0 drivers/net/bonding/bond_alb.c:1477
CPU: 0 PID: 12743 Comm: syz-executor.4 Not tainted 5.6.0-rc2-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
 __dump_stack lib/dump_stack.c:77 [inline]
 dump_stack+0x1c9/0x220 lib/dump_stack.c:118
 kmsan_report+0xf7/0x1e0 mm/kmsan/kmsan_report.c:118
 __msan_warning+0x58/0xa0 mm/kmsan/kmsan_instr.c:215
 bond_slave_has_mac_rx include/net/bonding.h:704 [inline]
 rlb_arp_xmit drivers/net/bonding/bond_alb.c:662 [inline]
 bond_alb_xmit+0x575/0x25e0 drivers/net/bonding/bond_alb.c:1477
 __bond_start_xmit drivers/net/bonding/bond_main.c:4257 [inline]
 bond_start_xmit+0x85d/0x2f70 drivers/net/bonding/bond_main.c:4282
 __netdev_start_xmit include/linux/netdevice.h:4524 [inline]
 netdev_start_xmit include/linux/netdevice.h:4538 [inline]
 xmit_one net/core/dev.c:3470 [inline]
 dev_hard_start_xmit+0x531/0xab0 net/core/dev.c:3486
 __dev_queue_xmit+0x37de/0x4220 net/core/dev.c:4063
 dev_queue_xmit+0x4b/0x60 net/core/dev.c:4096
 packet_snd net/packet/af_packet.c:2967 [inline]
 packet_sendmsg+0x8347/0x93b0 net/packet/af_packet.c:2992
 sock_sendmsg_nosec net/socket.c:652 [inline]
 sock_sendmsg net/socket.c:672 [inline]
 __sys_sendto+0xc1b/0xc50 net/socket.c:1998
 __do_sys_sendto net/socket.c:2010 [inline]
 __se_sys_sendto+0x107/0x130 net/socket.c:2006
 __x64_sys_sendto+0x6e/0x90 net/socket.c:2006
 do_syscall_64+0xb8/0x160 arch/x86/entry/common.c:296
 entry_SYSCALL_64_after_hwframe+0x44/0xa9
RIP: 0033:0x45c479
Code: ad b6 fb ff c3 66 2e 0f 1f 84 00 00 00 00 00 66 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 7b b6 fb ff c3 66 2e 0f 1f 84 00 00 00 00
RSP: 002b:00007fc77ffbbc78 EFLAGS: 00000246 ORIG_RAX: 000000000000002c
RAX: ffffffffffffffda RBX: 00007fc77ffbc6d4 RCX: 000000000045c479
RDX: 000000000000000e RSI: 00000000200004c0 RDI: 0000000000000003
RBP: 000000000076bf20 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 00000000ffffffff
R13: 0000000000000a04 R14: 00000000004cc7b0 R15: 000000000076bf2c

Uninit was created at:
 kmsan_save_stack_with_flags mm/kmsan/kmsan.c:144 [inline]
 kmsan_internal_poison_shadow+0x66/0xd0 mm/kmsan/kmsan.c:127
 kmsan_slab_alloc+0x8a/0xe0 mm/kmsan/kmsan_hooks.c:82
 slab_alloc_node mm/slub.c:2793 [inline]
 __kmalloc_node_track_caller+0xb40/0x1200 mm/slub.c:4401
 __kmalloc_reserve net/core/skbuff.c:142 [inline]
 __alloc_skb+0x2fd/0xac0 net/core/skbuff.c:210
 alloc_skb include/linux/skbuff.h:1051 [inline]
 alloc_skb_with_frags+0x18c/0xa70 net/core/skbuff.c:5766
 sock_alloc_send_pskb+0xada/0xc60 net/core/sock.c:2242
 packet_alloc_skb net/packet/af_packet.c:2815 [inline]
 packet_snd net/packet/af_packet.c:2910 [inline]
 packet_sendmsg+0x66a0/0x93b0 net/packet/af_packet.c:2992
 sock_sendmsg_nosec net/socket.c:652 [inline]
 sock_sendmsg net/socket.c:672 [inline]
 __sys_sendto+0xc1b/0xc50 net/socket.c:1998
 __do_sys_sendto net/socket.c:2010 [inline]
 __se_sys_sendto+0x107/0x130 net/socket.c:2006
 __x64_sys_sendto+0x6e/0x90 net/socket.c:2006
 do_syscall_64+0xb8/0x160 arch/x86/entry/common.c:296
 entry_SYSCALL_64_after_hwframe+0x44/0xa9

Fixes: 1da177e4 ("Linux-2.6.12-rc2")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Madalin Bucur says:

====================
QorIQ DPAA FMan erratum A050385 workaround

Changes in v2:
 - added CONFIG_DPAA_ERRATUM_A050385
 - removed unnecessary parenthesis
 - changed alignment defines to use only decimal values

The patch set implements the workaround for FMan erratum A050385:

FMAN DMA read or writes under heavy traffic load may cause FMAN
internal resource leak; thus stopping further packet processing.
To reproduce this issue when the workaround is not applied, one
needs to ensure the FMan DMA transaction queue is already full
when a transaction split occurs so the system must be under high
traffic load (i.e. multiple ports at line rate). After the errata
occurs, the traffic stops. The only SoC impacted by this is the
LS1043A, the other ARM DPAA 1 SoC or the PPC DPAA 1 SoCs do not
have this erratum.

The FMAN internal queue can overflow when FMAN splits single
read or write transactions into multiple smaller transactions
such that more than 17 AXI transactions are in flight from FMAN
to interconnect. When the FMAN internal queue overflows, it can
stall further packet processing. The issue can occur with any one
of the following three conditions:

  1. FMAN AXI transaction crosses 4K address boundary (Errata
         A010022)
  2. FMAN DMA address for an AXI transaction is not 16 byte
         aligned, i.e. the last 4 bits of an address are non-zero
  3. Scatter Gather (SG) frames have more than one SG buffer in
         the SG list and any one of the buffers, except the last
         buffer in the SG list has data size that is not a multiple
         of 16 bytes, i.e., other than 16, 32, 48, 64, etc.

With any one of the above three conditions present, there is
likelihood of stalled FMAN packet processing, especially under
stress with multiple ports injecting line-rate traffic.

To avoid situations that stall FMAN packet processing, all of the
above three conditions must be avoided; therefore, configure the
system with the following rules:

  1. Frame buffers must not span a 4KB address boundary, unless
         the frame start address is 256 byte aligned
  2. All FMAN DMA start addresses (for example, BMAN buffer
         address, FD[address] + FD[offset]) are 16B aligned
  3. SG table and buffer addresses are 16B aligned and the size
         of SG buffers are multiple of 16 bytes, except for the last
         SG buffer that can be of any size.

Additional workaround notes:
- Address alignment of 64 bytes is recommended for maximally
efficient system bus transactions (although 16 byte alignment is
sufficient to avoid the stall condition)
- To support frame sizes that are larger than 4K bytes, there are
two options:
  1. Large single buffer frames that span a 4KB page boundary can
         be converted into SG frames to avoid transaction splits at
         the 4KB boundary,
  2. Align the large single buffer to 256B address boundaries,
         ensure that the frame address plus offset is 256B aligned.
- If software generated SG frames have buffers that are unaligned
and with random non-multiple of 16 byte lengths, before
transmitting such frames via FMAN, frames will need to be copied
into a new single buffer or multiple buffer SG frame that is
compliant with the three rules listed above.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Align buffers, data start, SG fragment length to avoid DMA splits.
These changes prevent the A050385 erratum to manifest itself:

FMAN DMA read or writes under heavy traffic load may cause FMAN
internal resource leak; thus stopping further packet processing.

The FMAN internal queue can overflow when FMAN splits single
read or write transactions into multiple smaller transactions
such that more than 17 AXI transactions are in flight from FMAN
to interconnect. When the FMAN internal queue overflows, it can
stall further packet processing. The issue can occur with any one
of the following three conditions:

  1. FMAN AXI transaction crosses 4K address boundary (Errata
	 A010022)
  2. FMAN DMA address for an AXI transaction is not 16 byte
	 aligned, i.e. the last 4 bits of an address are non-zero
  3. Scatter Gather (SG) frames have more than one SG buffer in
	 the SG list and any one of the buffers, except the last
	 buffer in the SG list has data size that is not a multiple
	 of 16 bytes, i.e., other than 16, 32, 48, 64, etc.

With any one of the above three conditions present, there is
likelihood of stalled FMAN packet processing, especially under
stress with multiple ports injecting line-rate traffic.

To avoid situations that stall FMAN packet processing, all of the
above three conditions must be avoided; therefore, configure the
system with the following rules:

  1. Frame buffers must not span a 4KB address boundary, unless
	 the frame start address is 256 byte aligned
  2. All FMAN DMA start addresses (for example, BMAN buffer
	 address, FD[address] + FD[offset]) are 16B aligned
  3. SG table and buffer addresses are 16B aligned and the size
	 of SG buffers are multiple of 16 bytes, except for the last
	 SG buffer that can be of any size.

Additional workaround notes:
- Address alignment of 64 bytes is recommended for maximally
efficient system bus transactions (although 16 byte alignment is
sufficient to avoid the stall condition)
- To support frame sizes that are larger than 4K bytes, there are
two options:
  1. Large single buffer frames that span a 4KB page boundary can
	 be converted into SG frames to avoid transaction splits at
	 the 4KB boundary,
  2. Align the large single buffer to 256B address boundaries,
	 ensure that the frame address plus offset is 256B aligned.
- If software generated SG frames have buffers that are unaligned
and with random non-multiple of 16 byte lengths, before
transmitting such frames via FMAN, frames will need to be copied
into a new single buffer or multiple buffer SG frame that is
compliant with the three rules listed above.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Detect the presence of the A050385 erratum.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The LS1043A SoC is affected by the A050385 erratum stating that
FMAN DMA read or writes under heavy traffic load may cause FMAN
internal resource leak thus stopping further packet processing.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

FMAN DMA read or writes under heavy traffic load may cause FMAN
internal resource leak; thus stopping further packet processing.

The FMAN internal queue can overflow when FMAN splits single
read or write transactions into multiple smaller transactions
such that more than 17 AXI transactions are in flight from FMAN
to interconnect. When the FMAN internal queue overflows, it can
stall further packet processing. The issue can occur with any one
of the following three conditions:

  1. FMAN AXI transaction crosses 4K address boundary (Errata
     A010022)
  2. FMAN DMA address for an AXI transaction is not 16 byte
     aligned, i.e. the last 4 bits of an address are non-zero
  3. Scatter Gather (SG) frames have more than one SG buffer in
     the SG list and any one of the buffers, except the last
     buffer in the SG list has data size that is not a multiple
     of 16 bytes, i.e., other than 16, 32, 48, 64, etc.

With any one of the above three conditions present, there is
likelihood of stalled FMAN packet processing, especially under
stress with multiple ports injecting line-rate traffic.

To avoid situations that stall FMAN packet processing, all of the
above three conditions must be avoided; therefore, configure the
system with the following rules:

  1. Frame buffers must not span a 4KB address boundary, unless
     the frame start address is 256 byte aligned
  2. All FMAN DMA start addresses (for example, BMAN buffer
     address, FD[address] + FD[offset]) are 16B aligned
  3. SG table and buffer addresses are 16B aligned and the size
     of SG buffers are multiple of 16 bytes, except for the last
     SG buffer that can be of any size.

Additional workaround notes:
- Address alignment of 64 bytes is recommended for maximally
efficient system bus transactions (although 16 byte alignment is
sufficient to avoid the stall condition)
- To support frame sizes that are larger than 4K bytes, there are
two options:
  1. Large single buffer frames that span a 4KB page boundary can
     be converted into SG frames to avoid transaction splits at
     the 4KB boundary,
  2. Align the large single buffer to 256B address boundaries,
     ensure that the frame address plus offset is 256B aligned.
- If software generated SG frames have buffers that are unaligned
and with random non-multiple of 16 byte lengths, before
transmitting such frames via FMAN, frames will need to be copied
into a new single buffer or multiple buffer SG frame that is
compliant with the three rules listed above.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
Netfilter fixes for net

The following patchset contains Netfilter fixes for net:

1) Patches to bump position index from sysctl seq_next,
   from Vasilin Averin.

2) Release flowtable hook from error path, from Florian Westphal.

3) Patches to add missing netlink attribute validation,
   from Jakub Kicinski.

4) Missing NFTA_CHAIN_FLAGS in nf_tables_fill_chain_info().

5) Infinite loop in module autoload if extension is not available,
   from Florian Westphal.

6) Missing module ownership in inet/nat chain type definition.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Set owner to THIS_MODULE, otherwise the nft_chain_nat module might be
removed while there are still inet/nat chains in place.

[  117.942096] BUG: unable to handle page fault for address: ffffffffa0d5e040
[  117.942101] #PF: supervisor read access in kernel mode
[  117.942103] #PF: error_code(0x0000) - not-present page
[  117.942106] PGD 200c067 P4D 200c067 PUD 200d063 PMD 3dc909067 PTE 0
[  117.942113] Oops: 0000 [#1] PREEMPT SMP PTI
[  117.942118] CPU: 3 PID: 27 Comm: kworker/3:0 Not tainted 5.6.0-rc3+ #348
[  117.942133] Workqueue: events nf_tables_trans_destroy_work [nf_tables]
[  117.942145] RIP: 0010:nf_tables_chain_destroy.isra.0+0x94/0x15a [nf_tables]
[  117.942149] Code: f6 45 54 01 0f 84 d1 00 00 00 80 3b 05 74 44 48 8b 75 e8 48 c7 c7 72 be de a0 e8 56 e6 2d e0 48 8b 45 e8 48 c7 c7 7f be de a0 <48> 8b 30 e8 43 e6 2d e0 48 8b 45 e8 48 8b 40 10 48 85 c0 74 5b 8b
[  117.942152] RSP: 0018:ffffc9000015be10 EFLAGS: 00010292
[  117.942155] RAX: ffffffffa0d5e040 RBX: ffff88840be87fc2 RCX: 0000000000000007
[  117.942158] RDX: 0000000000000007 RSI: 0000000000000086 RDI: ffffffffa0debe7f
[  117.942160] RBP: ffff888403b54b50 R08: 0000000000001482 R09: 0000000000000004
[  117.942162] R10: 0000000000000000 R11: 0000000000000001 R12: ffff8883eda7e540
[  117.942164] R13: dead000000000122 R14: dead000000000100 R15: ffff888403b3db80
[  117.942167] FS:  0000000000000000(0000) GS:ffff88840e4c0000(0000) knlGS:0000000000000000
[  117.942169] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[  117.942172] CR2: ffffffffa0d5e040 CR3: 00000003e4c52002 CR4: 00000000001606e0
[  117.942174] Call Trace:
[  117.942188]  nf_tables_trans_destroy_work.cold+0xd/0x12 [nf_tables]
[  117.942196]  process_one_work+0x1d6/0x3b0
[  117.942200]  worker_thread+0x45/0x3c0
[  117.942203]  ? process_one_work+0x3b0/0x3b0
[  117.942210]  kthread+0x112/0x130
[  117.942214]  ? kthread_create_worker_on_cpu+0x40/0x40
[  117.942221]  ret_from_fork+0x35/0x40

nf_tables_chain_destroy() crashes on module_put() because the module is
gone.

Fixes: d164385e ("netfilter: nat: add inet family nat support")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Currently passive MPTCP socket can skip including the DACK
option - if the peer sends data before accept() completes.

The above happens because the msk 'can_ack' flag is set
only after the accept() call.

Such missing DACK option may cause - as per RFC spec -
unwanted fallback to TCP.

This change addresses the issue using the key material
available in the current subflow, if any, to create a suitable
dack option when msk ack seq is not yet available.

v1 -> v2:
 - adavance the generated ack after the initial MPC packet

Fixes: d22f4988 ("mptcp: process MP_CAPABLE data option")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is similar to commit 674d9de0 ("NFC: Fix possible memory
corruption when handling SHDLC I-Frame commands") and commit d7ee81ad
("NFC: nci: Add some bounds checking in nci_hci_cmd_received()") which
added range checks on "pipe".

The "pipe" variable comes skb->data[0] in nfc_hci_msg_rx_work().
It's in the 0-255 range.  We're using it as the array index into the
hdev->pipes[] array which has NFC_HCI_MAX_PIPES (128) members.

Fixes: 118278f2 ("NFC: hci: Add pipes table to reference them with a tuple {gate, host}")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When local NET_RX backlog is full due to traffic overrun,
peer veth tx_dropped counter increases. At that time, list
local veth stats, rx_dropped has double value of peer
tx_dropped, even bigger than transmit packets by peer.

In NET_RX softirq process, if any packet drop case happens,
it increases dev's rx_dropped counter and returns NET_RX_DROP.

At veth tx side, it records any error returned from peer netif_rx
into local dev tx_dropped counter.

In veth get stats process, it puts local dev rx_dropped and
peer dev tx_dropped into together as local rx_drpped value.
So that it shows double value of real dropped packets number in
this case.

This patch ignores peer tx_dropped when counting local rx_dropped,
since peer tx_dropped is duplicated to local rx_dropped at most cases.
Signed-off-by: Jiang Lidong <jianglidong3@jd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'wireless-drivers-2020-03-05' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers

Kalle Valo says:

====================
wireless-drivers fixes for v5.6

Second set of fixes for v5.6. Only two small fixes this time.

iwlwifi

* fix another initialisation regression with 3168 devices

mt76

* fix memory corruption with too many rx fragments
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

We now ignore the "completion" event when using tx queue timestamping,
and only pay attention to the two (high and low) timestamp events. The
NIC will send a pair of timestamp events for every packet transmitted.
The current firmware may merge the completion events, and it is possible
that future versions may reorder the completion and timestamp events.
As such the completion event is not useful.

Without this patch in place a merged completion event on a queue with
timestamping will cause a "spurious TX completion" error. This affects
SFN8000-series adapters.
Signed-off-by: Tom Zhao <tzhao@solarflare.com>
Acked-by: Martin Habets <mhabets@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When fibre port supports auto-negotiation, the IMP(Intelligent
Management Process) processes the speed of auto-negotiation
and the  user's speed separately.
For below case, the port will get a not link up problem.
step 1: disables auto-negotiation and sets speed to A, then
the driver's MAC speed will be updated to A.
step 2: enables auto-negotiation and MAC gets negotiated
speed B, then the driver's MAC speed will be updated to B
through querying in periodical task.
step 3: MAC gets new negotiated speed A.
step 4: disables auto-negotiation and sets speed to B before
periodical task query new MAC speed A, the driver will  ignore
the speed configuration.

This patch fixes it by skipping speed and duplex checking when
fibre port supports auto-negotiation.

Fixes: 22f48e24 ("net: hns3: add autoneg and change speed support for fibre port")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Before accessing various fields in IPV4 network header
and TCP header, make sure the packet :

- Has IP version 4 (ip->version == 4)
- Has not a silly network length (ip->ihl >= 5)
- Is big enough to hold network and transport headers
- Has not a silly TCP header size (th->doff >= sizeof(struct tcphdr) / 4)

syzbot reported :

BUG: KMSAN: uninit-value in slhc_compress+0x5b9/0x2e60 drivers/net/slip/slhc.c:270
CPU: 0 PID: 11728 Comm: syz-executor231 Not tainted 5.6.0-rc2-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
 __dump_stack lib/dump_stack.c:77 [inline]
 dump_stack+0x1c9/0x220 lib/dump_stack.c:118
 kmsan_report+0xf7/0x1e0 mm/kmsan/kmsan_report.c:118
 __msan_warning+0x58/0xa0 mm/kmsan/kmsan_instr.c:215
 slhc_compress+0x5b9/0x2e60 drivers/net/slip/slhc.c:270
 ppp_send_frame drivers/net/ppp/ppp_generic.c:1637 [inline]
 __ppp_xmit_process+0x1902/0x2970 drivers/net/ppp/ppp_generic.c:1495
 ppp_xmit_process+0x147/0x2f0 drivers/net/ppp/ppp_generic.c:1516
 ppp_write+0x6bb/0x790 drivers/net/ppp/ppp_generic.c:512
 do_loop_readv_writev fs/read_write.c:717 [inline]
 do_iter_write+0x812/0xdc0 fs/read_write.c:1000
 compat_writev+0x2df/0x5a0 fs/read_write.c:1351
 do_compat_pwritev64 fs/read_write.c:1400 [inline]
 __do_compat_sys_pwritev fs/read_write.c:1420 [inline]
 __se_compat_sys_pwritev fs/read_write.c:1414 [inline]
 __ia32_compat_sys_pwritev+0x349/0x3f0 fs/read_write.c:1414
 do_syscall_32_irqs_on arch/x86/entry/common.c:339 [inline]
 do_fast_syscall_32+0x3c7/0x6e0 arch/x86/entry/common.c:410
 entry_SYSENTER_compat+0x68/0x77 arch/x86/entry/entry_64_compat.S:139
RIP: 0023:0xf7f7cd99
Code: 90 e8 0b 00 00 00 f3 90 0f ae e8 eb f9 8d 74 26 00 89 3c 24 c3 90 90 90 90 90 90 90 90 90 90 90 90 51 52 55 89 e5 0f 34 cd 80 <5d> 5a 59 c3 90 90 90 90 eb 0d 90 90 90 90 90 90 90 90 90 90 90 90
RSP: 002b:00000000ffdb84ac EFLAGS: 00000217 ORIG_RAX: 000000000000014e
RAX: ffffffffffffffda RBX: 0000000000000003 RCX: 00000000200001c0
RDX: 0000000000000001 RSI: 0000000000000000 RDI: 0000000000000003
RBP: 0000000040047459 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000000 R12: 0000000000000000
R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000000

Uninit was created at:
 kmsan_save_stack_with_flags mm/kmsan/kmsan.c:144 [inline]
 kmsan_internal_poison_shadow+0x66/0xd0 mm/kmsan/kmsan.c:127
 kmsan_slab_alloc+0x8a/0xe0 mm/kmsan/kmsan_hooks.c:82
 slab_alloc_node mm/slub.c:2793 [inline]
 __kmalloc_node_track_caller+0xb40/0x1200 mm/slub.c:4401
 __kmalloc_reserve net/core/skbuff.c:142 [inline]
 __alloc_skb+0x2fd/0xac0 net/core/skbuff.c:210
 alloc_skb include/linux/skbuff.h:1051 [inline]
 ppp_write+0x115/0x790 drivers/net/ppp/ppp_generic.c:500
 do_loop_readv_writev fs/read_write.c:717 [inline]
 do_iter_write+0x812/0xdc0 fs/read_write.c:1000
 compat_writev+0x2df/0x5a0 fs/read_write.c:1351
 do_compat_pwritev64 fs/read_write.c:1400 [inline]
 __do_compat_sys_pwritev fs/read_write.c:1420 [inline]
 __se_compat_sys_pwritev fs/read_write.c:1414 [inline]
 __ia32_compat_sys_pwritev+0x349/0x3f0 fs/read_write.c:1414
 do_syscall_32_irqs_on arch/x86/entry/common.c:339 [inline]
 do_fast_syscall_32+0x3c7/0x6e0 arch/x86/entry/common.c:410
 entry_SYSENTER_compat+0x68/0x77 arch/x86/entry/entry_64_compat.S:139

Fixes: b5451d78 ("slip: Move the SLIP drivers")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

nft will loop forever if the kernel doesn't support an expression:

1. nft_expr_type_get() appends the family specific name to the module list.
2. -EAGAIN is returned to nfnetlink, nfnetlink calls abort path.
3. abort path sets ->done to true and calls request_module for the
   expression.
4. nfnetlink replays the batch, we end up in nft_expr_type_get() again.
5. nft_expr_type_get attempts to append family-specific name. This
   one already exists on the list, so we continue
6. nft_expr_type_get adds the generic expression name to the module
   list. -EAGAIN is returned, nfnetlink calls abort path.
7. abort path encounters the family-specific expression which
   has 'done' set, so it gets removed.
8. abort path requests the generic expression name, sets done to true.
9. batch is replayed.

If the expression could not be loaded, then we will end up back at 1),
because the family-specific name got removed and the cycle starts again.

Note that userspace can SIGKILL the nft process to stop the cycle, but
the desired behaviour is to return an error after the generic expr name
fails to load the expression.

Fixes: eb014de4 ("netfilter: nf_tables: autoload modules from the abort path")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Missing NFTA_CHAIN_FLAGS netlink attribute when dumping basechain
definitions.

Fixes: c9626a2c ("netfilter: nf_tables: add hardware offload support")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

When registers a phy_device successful, should terminate the loop
or the phy_device would be registered in other addr. If there are
multiple PHYs without reg properties, it will go wrong.
Signed-off-by: Dajun Jin <adajunjin@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Hardware can support more than 8 queues currently limited by
netif_get_num_default_rss_queues(). So, rework and fix checks for max
number of queues to allocate. The checks should be based on how many are
actually supported by hardware, OR the number of online cpus; whichever
is lower.

Fixes: 5952dde7 ("cxgb4: set maximal number of default RSS queues")
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>"
Signed-off-by: David S. Miller <davem@davemloft.net>

This should improve the error message when the PHY validate in the MAC
driver failed. I ran into this problem multiple times that I put wrong
interface values into the device tree and was searching why it is
failing with -22 (-EINVAL). This should make it easier to spot the
problem.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

719655a1 ("net: phy: Replace phy driver features u32 with link_mode
bitmap") was a bit over-eager and also removed the second phy driver's
name, resulting in a nasty OOPS on registration:

[    1.319854] CPU 0 Unable to handle kernel paging request at virtual address 00000000, epc == 804dd50c, ra == 804dd4f0
[    1.330859] Oops[#1]:
[    1.333138] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.4.22 #0
[    1.339217] $ 0   : 00000000 00000001 87ca7f00 805c1874
[    1.344590] $ 4   : 00000000 00000047 00585000 8701f800
[    1.349965] $ 8   : 8701f800 804f4a5c 00000003 64726976
[    1.355341] $12   : 00000001 00000000 00000000 00000114
[    1.360718] $16   : 87ca7f80 00000000 00000000 80639fe4
[    1.366093] $20   : 00000002 00000000 806441d0 80b90000
[    1.371470] $24   : 00000000 00000000
[    1.376847] $28   : 87c1e000 87c1fda0 80b90000 804dd4f0
[    1.382224] Hi    : d1c8f8da
[    1.385180] Lo    : 5518a480
[    1.388182] epc   : 804dd50c kset_find_obj+0x3c/0x114
[    1.393345] ra    : 804dd4f0 kset_find_obj+0x20/0x114
[    1.398530] Status: 10008703 KERNEL EXL IE
[    1.402833] Cause : 00800008 (ExcCode 02)
[    1.406952] BadVA : 00000000
[    1.409913] PrId  : 0002a075 (Broadcom BMIPS4350)
[    1.414745] Modules linked in:
[    1.417895] Process swapper/0 (pid: 1, threadinfo=(ptrval), task=(ptrval), tls=00000000)
[    1.426214] Stack : 87cec000 80630000 80639370 80640658 80640000 80049af4 80639fe4 8063a0d8
[    1.434816]         8063a0d8 802ef078 00000002 00000000 806441d0 80b90000 8063a0d8 802ef114
[    1.443417]         87cea0de 87c1fde0 00000000 804de488 87cea000 8063a0d8 8063a0d8 80334e48
[    1.452018]         80640000 8063984c 80639bf4 00000000 8065de48 00000001 8063a0d8 80334ed0
[    1.460620]         806441d0 80b90000 80b90000 802ef164 8065dd70 80620000 80b90000 8065de58
[    1.469222]         ...
[    1.471734] Call Trace:
[    1.474255] [<804dd50c>] kset_find_obj+0x3c/0x114
[    1.479141] [<802ef078>] driver_find+0x1c/0x44
[    1.483665] [<802ef114>] driver_register+0x74/0x148
[    1.488719] [<80334e48>] phy_driver_register+0x9c/0xd0
[    1.493968] [<80334ed0>] phy_drivers_register+0x54/0xe8
[    1.499345] [<8001061c>] do_one_initcall+0x7c/0x1f4
[    1.504374] [<80644ed8>] kernel_init_freeable+0x1d4/0x2b4
[    1.509940] [<804f4e24>] kernel_init+0x10/0xf8
[    1.514502] [<80018e68>] ret_from_kernel_thread+0x14/0x1c
[    1.520040] Code: 1060000c  02202025  90650000 <90810000> 24630001  14250004  24840001  14a0fffb  90650000
[    1.530061]
[    1.531698] ---[ end trace d52f1717cd29bdc8 ]---

Fix it by readding the name.

Fixes: 719655a1 ("net: phy: Replace phy driver features u32 with link_mode bitmap")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The devlink trigger command does not exist. While rewriting the
documentation for devlink into the reStructuredText format,
documentation for the trigger command was accidentally merged in. This
occurred because the author was also working on a potential extension to
devlink regions which included this trigger command, and accidentally
squashed the documentation incorrectly.

Further review eventually settled on using the previously unused "new"
command instead of creating a new trigger command.

Fix this by removing mention of the trigger command from the
documentation.

Fixes: 0b0f945f ("devlink: add a file documenting devlink regions", 2020-01-10)
Noticed-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add missing attribute validation for tunnel source and
destination ports to the netlink policy.

Fixes: af308b94 ("netfilter: nf_tables: add tunnel support")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Add missing attribute validation for NFTA_PAYLOAD_CSUM_FLAGS
to the netlink policy.

Fixes: 18140969 ("netfilter: nft_payload: layer 4 checksum adjustment for pseudoheader fields")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Add missing attribute validation for cthelper
to the netlink policy.

Fixes: 12f7a505 ("netfilter: add user-space connection tracking helper infrastructure")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

If hook registration fails, the hooks allocated via nft_netdev_hook_alloc
need to be freed.

We can't change the goto label to 'goto 5' -- while it does fix the memleak
it does cause a warning splat from the netfilter core (the hooks were not
registered).

Fixes: 3f0465a9 ("netfilter: nf_tables: dynamically allocate hooks per net_device in flowtables")
Reported-by: syzbot+a2ff6fa45162a5ed4dd3@syzkaller.appspotmail.com
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

If .next function does not change position index,
following .show function will repeat output related
to current position index.

Without patch:
 # dd if=/proc/net/ip_tables_matches  # original file output
 conntrack
 conntrack
 conntrack
 recent
 recent
 icmp
 udplite
 udp
 tcp
 0+1 records in
 0+1 records out
 65 bytes copied, 5.4074e-05 s, 1.2 MB/s

 # dd if=/proc/net/ip_tables_matches bs=62 skip=1
 dd: /proc/net/ip_tables_matches: cannot skip to specified offset
 cp   <<< end of  last line
 tcp  <<< and then unexpected whole last line once again
 0+1 records in
 0+1 records out
 7 bytes copied, 0.000102447 s, 68.3 kB/s

Cc: stable@vger.kernel.org
Fixes: 1f4aace6 ("fs/seq_file.c: simplify seq_file iteration code ...")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=206283Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

If .next function does not change position index,
following .show function will repeat output related
to current position index.

Without the patch:
 # dd if=/proc/net/xt_recent/SSH # original file outpt
 src=127.0.0.4 ttl: 0 last_seen: 6275444819 oldest_pkt: 1 6275444819
 src=127.0.0.2 ttl: 0 last_seen: 6275438906 oldest_pkt: 1 6275438906
 src=127.0.0.3 ttl: 0 last_seen: 6275441953 oldest_pkt: 1 6275441953
 0+1 records in
 0+1 records out
 204 bytes copied, 6.1332e-05 s, 3.3 MB/s

Read after lseek into middle of last line (offset 140 in example below)
generates expected end of last line and then unexpected whole last line
once again

 # dd if=/proc/net/xt_recent/SSH bs=140 skip=1
 dd: /proc/net/xt_recent/SSH: cannot skip to specified offset
 127.0.0.3 ttl: 0 last_seen: 6275441953 oldest_pkt: 1 6275441953
 src=127.0.0.3 ttl: 0 last_seen: 6275441953 oldest_pkt: 1 6275441953
 0+1 records in
 0+1 records out
 132 bytes copied, 6.2487e-05 s, 2.1 MB/s

Cc: stable@vger.kernel.org
Fixes: 1f4aace6 ("fs/seq_file.c: simplify seq_file iteration code ...")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=206283Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

If .next function does not change position index,
following .show function will repeat output related
to current position index.

Cc: stable@vger.kernel.org
Fixes: 1f4aace6 ("fs/seq_file.c: simplify seq_file iteration code ...")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=206283Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

If .next function does not change position index,
following .show function will repeat output related
to current position index.

Cc: stable@vger.kernel.org
Fixes: 1f4aace6 ("fs/seq_file.c: simplify seq_file iteration code ...")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=206283Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Place phylink_start()/phylink_stop() inside dsa_port_enable() and
dsa_port_disable(), which ensures that we call phylink_stop() before
tearing down phylink - which is a documented requirement.  Failure
to do so can cause use-after-free bugs.

Fixes: 0e279218 ("net: dsa: Use PHYLINK for the CPU/DSA ports")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Hangbin Liu says:

====================
Fix IPv6 peer route update

Currently we have two issues for peer route update on IPv6.
1. When update peer route metric, we only updated the local one.
2. If peer address changed, we didn't remove the old one and add new one.

The first two patches fixed these issues and the third patch add new
tests to cover it.

With the fixes and updated test:
]# ./fib_tests.sh
IPv6 prefix route tests
    TEST: Default metric                                                [ OK ]
    TEST: User specified metric on first device                         [ OK ]
    TEST: User specified metric on second device                        [ OK ]
    TEST: Delete of address on first device                             [ OK ]
    TEST: Modify metric of address                                      [ OK ]
    TEST: Prefix route removed on link down                             [ OK ]
    TEST: Prefix route with metric on link up                           [ OK ]
    TEST: Set metric with peer route on local side                      [ OK ]
    TEST: User specified metric on local address                        [ OK ]
    TEST: Set metric with peer route on peer side                       [ OK ]
    TEST: Modify metric with peer route on local side                   [ OK ]
    TEST: Modify metric with peer route on peer side                    [ OK ]

IPv4 prefix route tests
    TEST: Default metric                                                [ OK ]
    TEST: User specified metric on first device                         [ OK ]
    TEST: User specified metric on second device                        [ OK ]
    TEST: Delete of address on first device                             [ OK ]
    TEST: Modify metric of address                                      [ OK ]
    TEST: Prefix route removed on link down                             [ OK ]
    TEST: Prefix route with metric on link up                           [ OK ]
    TEST: Modify metric of .0/24 address                                [ OK ]
    TEST: Set metric of address with peer route                         [ OK ]
    TEST: Modify metric of address with peer route                      [ OK ]

Tests passed:  22
Tests failed:   0
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch update {ipv4, ipv6}_addr_metric_test with
1. Set metric of address with peer route and see if the route added
correctly.
2. Modify metric and peer address for peer route and see if the route
changed correctly.
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When we modify the peer route and changed it to a new one, we should
remove the old route first. Before the fix:

+ ip addr add dev dummy1 2001:db8::1 peer 2001:db8::2
+ ip -6 route show dev dummy1
2001:db8::1 proto kernel metric 256 pref medium
2001:db8::2 proto kernel metric 256 pref medium
+ ip addr change dev dummy1 2001:db8::1 peer 2001:db8::3
+ ip -6 route show dev dummy1
2001:db8::1 proto kernel metric 256 pref medium
2001:db8::2 proto kernel metric 256 pref medium

After the fix:
+ ip addr change dev dummy1 2001:db8::1 peer 2001:db8::3
+ ip -6 route show dev dummy1
2001:db8::1 proto kernel metric 256 pref medium
2001:db8::3 proto kernel metric 256 pref medium

This patch depend on the previous patch "net/ipv6: need update peer route
when modify metric" to update new peer route after delete old one.
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When we modify the route metric, the peer address's route need also
be updated. Before the fix:

+ ip addr add dev dummy1 2001:db8::1 peer 2001:db8::2 metric 60
+ ip -6 route show dev dummy1
2001:db8::1 proto kernel metric 60 pref medium
2001:db8::2 proto kernel metric 60 pref medium
+ ip addr change dev dummy1 2001:db8::1 peer 2001:db8::2 metric 61
+ ip -6 route show dev dummy1
2001:db8::1 proto kernel metric 61 pref medium
2001:db8::2 proto kernel metric 60 pref medium

After the fix:
+ ip addr change dev dummy1 2001:db8::1 peer 2001:db8::2 metric 61
+ ip -6 route show dev dummy1
2001:db8::1 proto kernel metric 61 pref medium
2001:db8::2 proto kernel metric 61 pref medium

Fixes: 8308f3ff ("net/ipv6: Add support for specifying metric of connected routes")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>